summaryrefslogtreecommitdiffstats
path: root/drivers/net/dsa/mv88e6060.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/dsa/mv88e6060.c')
-rw-r--r--drivers/net/dsa/mv88e6060.c54
1 files changed, 23 insertions, 31 deletions
diff --git a/drivers/net/dsa/mv88e6060.c b/drivers/net/dsa/mv88e6060.c
index 325391d19bad..7a54ec04b418 100644
--- a/drivers/net/dsa/mv88e6060.c
+++ b/drivers/net/dsa/mv88e6060.c
@@ -8,6 +8,8 @@
* (at your option) any later version.
*/
+#include <linux/delay.h>
+#include <linux/jiffies.h>
#include <linux/list.h>
#include <linux/module.h>
#include <linux/netdevice.h>
@@ -66,36 +68,30 @@ static int mv88e6060_switch_reset(struct dsa_switch *ds)
{
int i;
int ret;
+ unsigned long timeout;
- /*
- * Set all ports to the disabled state.
- */
+ /* Set all ports to the disabled state. */
for (i = 0; i < 6; i++) {
ret = REG_READ(REG_PORT(i), 0x04);
REG_WRITE(REG_PORT(i), 0x04, ret & 0xfffc);
}
- /*
- * Wait for transmit queues to drain.
- */
- msleep(2);
+ /* Wait for transmit queues to drain. */
+ usleep_range(2000, 4000);
- /*
- * Reset the switch.
- */
+ /* Reset the switch. */
REG_WRITE(REG_GLOBAL, 0x0a, 0xa130);
- /*
- * Wait up to one second for reset to complete.
- */
- for (i = 0; i < 1000; i++) {
+ /* Wait up to one second for reset to complete. */
+ timeout = jiffies + 1 * HZ;
+ while (time_before(jiffies, timeout)) {
ret = REG_READ(REG_GLOBAL, 0x00);
if ((ret & 0x8000) == 0x0000)
break;
- msleep(1);
+ usleep_range(1000, 2000);
}
- if (i == 1000)
+ if (time_after(jiffies, timeout))
return -ETIMEDOUT;
return 0;
@@ -103,15 +99,13 @@ static int mv88e6060_switch_reset(struct dsa_switch *ds)
static int mv88e6060_setup_global(struct dsa_switch *ds)
{
- /*
- * Disable discarding of frames with excessive collisions,
+ /* Disable discarding of frames with excessive collisions,
* set the maximum frame size to 1536 bytes, and mask all
* interrupt sources.
*/
REG_WRITE(REG_GLOBAL, 0x04, 0x0800);
- /*
- * Enable automatic address learning, set the address
+ /* Enable automatic address learning, set the address
* database size to 1024 entries, and set the default aging
* time to 5 minutes.
*/
@@ -124,16 +118,14 @@ static int mv88e6060_setup_port(struct dsa_switch *ds, int p)
{
int addr = REG_PORT(p);
- /*
- * Do not force flow control, disable Ingress and Egress
+ /* Do not force flow control, disable Ingress and Egress
* Header tagging, disable VLAN tunneling, and set the port
* state to Forwarding. Additionally, if this is the CPU
* port, enable Ingress and Egress Trailer tagging mode.
*/
REG_WRITE(addr, 0x04, dsa_is_cpu_port(ds, p) ? 0x4103 : 0x0003);
- /*
- * Port based VLAN map: give each port its own address
+ /* Port based VLAN map: give each port its own address
* database, allow the CPU port to talk to each of the 'real'
* ports, and allow each of the 'real' ports to only talk to
* the CPU port.
@@ -144,8 +136,7 @@ static int mv88e6060_setup_port(struct dsa_switch *ds, int p)
ds->phys_port_mask :
(1 << ds->dst->cpu_port)));
- /*
- * Port Association Vector: when learning source addresses
+ /* Port Association Vector: when learning source addresses
* of packets, add the address to the address database using
* a port bitmap that has only the bit for this port set and
* the other bits clear.
@@ -245,7 +236,7 @@ static void mv88e6060_poll_link(struct dsa_switch *ds)
if (!link) {
if (netif_carrier_ok(dev)) {
- printk(KERN_INFO "%s: link down\n", dev->name);
+ netdev_info(dev, "link down\n");
netif_carrier_off(dev);
}
continue;
@@ -256,10 +247,11 @@ static void mv88e6060_poll_link(struct dsa_switch *ds)
fc = ((port_status & 0xc000) == 0xc000) ? 1 : 0;
if (!netif_carrier_ok(dev)) {
- printk(KERN_INFO "%s: link up, %d Mb/s, %s duplex, "
- "flow control %sabled\n", dev->name,
- speed, duplex ? "full" : "half",
- fc ? "en" : "dis");
+ netdev_info(dev,
+ "link up, %d Mb/s, %s duplex, flow control %sabled\n",
+ speed,
+ duplex ? "full" : "half",
+ fc ? "en" : "dis");
netif_carrier_on(dev);
}
}
OpenPOWER on IntegriCloud