diff options
Diffstat (limited to 'drivers/mtd/nand')
| -rw-r--r-- | drivers/mtd/nand/cafe_nand.c | 2 | ||||
| -rw-r--r-- | drivers/mtd/nand/mxc_nand.c | 92 | ||||
| -rw-r--r-- | drivers/mtd/nand/omap2.c | 2 |
3 files changed, 85 insertions, 11 deletions
diff --git a/drivers/mtd/nand/cafe_nand.c b/drivers/mtd/nand/cafe_nand.c index db1dfc5a1b11..e06c8983978e 100644 --- a/drivers/mtd/nand/cafe_nand.c +++ b/drivers/mtd/nand/cafe_nand.c @@ -2,7 +2,7 @@ * Driver for One Laptop Per Child ‘CAFÉ’ controller, aka Marvell 88ALP01 * * The data sheet for this device can be found at: - * http://www.marvell.com/products/pcconn/88ALP01.jsp + * http://wiki.laptop.org/go/Datasheets * * Copyright © 2006 Red Hat, Inc. * Copyright © 2006 David Woodhouse <dwmw2@infradead.org> diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/mxc_nand.c index b2828e84d243..214b03afdd48 100644 --- a/drivers/mtd/nand/mxc_nand.c +++ b/drivers/mtd/nand/mxc_nand.c @@ -30,6 +30,8 @@ #include <linux/clk.h> #include <linux/err.h> #include <linux/io.h> +#include <linux/irq.h> +#include <linux/completion.h> #include <asm/mach/flash.h> #include <mach/mxc_nand.h> @@ -151,7 +153,7 @@ struct mxc_nand_host { int irq; int eccsize; - wait_queue_head_t irq_waitq; + struct completion op_completion; uint8_t *data_buf; unsigned int buf_start; @@ -164,6 +166,7 @@ struct mxc_nand_host { void (*send_read_id)(struct mxc_nand_host *); uint16_t (*get_dev_status)(struct mxc_nand_host *); int (*check_int)(struct mxc_nand_host *); + void (*irq_control)(struct mxc_nand_host *, int); }; /* OOB placement block for use with hardware ecc generation */ @@ -216,9 +219,12 @@ static irqreturn_t mxc_nfc_irq(int irq, void *dev_id) { struct mxc_nand_host *host = dev_id; - disable_irq_nosync(irq); + if (!host->check_int(host)) + return IRQ_NONE; - wake_up(&host->irq_waitq); + host->irq_control(host, 0); + + complete(&host->op_completion); return IRQ_HANDLED; } @@ -245,11 +251,54 @@ static int check_int_v1_v2(struct mxc_nand_host *host) if (!(tmp & NFC_V1_V2_CONFIG2_INT)) return 0; - writew(tmp & ~NFC_V1_V2_CONFIG2_INT, NFC_V1_V2_CONFIG2); + if (!cpu_is_mx21()) + writew(tmp & ~NFC_V1_V2_CONFIG2_INT, NFC_V1_V2_CONFIG2); return 1; } +/* + * It has been observed that the i.MX21 cannot read the CONFIG2:INT bit + * if interrupts are masked (CONFIG1:INT_MSK is set). To handle this, the + * driver can enable/disable the irq line rather than simply masking the + * interrupts. + */ +static void irq_control_mx21(struct mxc_nand_host *host, int activate) +{ + if (activate) + enable_irq(host->irq); + else + disable_irq_nosync(host->irq); +} + +static void irq_control_v1_v2(struct mxc_nand_host *host, int activate) +{ + uint16_t tmp; + + tmp = readw(NFC_V1_V2_CONFIG1); + + if (activate) + tmp &= ~NFC_V1_V2_CONFIG1_INT_MSK; + else + tmp |= NFC_V1_V2_CONFIG1_INT_MSK; + + writew(tmp, NFC_V1_V2_CONFIG1); +} + +static void irq_control_v3(struct mxc_nand_host *host, int activate) +{ + uint32_t tmp; + + tmp = readl(NFC_V3_CONFIG2); + + if (activate) + tmp &= ~NFC_V3_CONFIG2_INT_MSK; + else + tmp |= NFC_V3_CONFIG2_INT_MSK; + + writel(tmp, NFC_V3_CONFIG2); +} + /* This function polls the NANDFC to wait for the basic operation to * complete by checking the INT bit of config2 register. */ @@ -259,10 +308,9 @@ static void wait_op_done(struct mxc_nand_host *host, int useirq) if (useirq) { if (!host->check_int(host)) { - - enable_irq(host->irq); - - wait_event(host->irq_waitq, host->check_int(host)); + INIT_COMPLETION(host->op_completion); + host->irq_control(host, 1); + wait_for_completion(&host->op_completion); } } else { while (max_retries-- > 0) { @@ -799,6 +847,7 @@ static void preset_v3(struct mtd_info *mtd) NFC_V3_CONFIG2_2CMD_PHASES | NFC_V3_CONFIG2_SPAS(mtd->oobsize >> 1) | NFC_V3_CONFIG2_ST_CMD(0x70) | + NFC_V3_CONFIG2_INT_MSK | NFC_V3_CONFIG2_NUM_ADDR_PHASE0; if (chip->ecc.mode == NAND_ECC_HW) @@ -1024,6 +1073,10 @@ static int __init mxcnd_probe(struct platform_device *pdev) host->send_read_id = send_read_id_v1_v2; host->get_dev_status = get_dev_status_v1_v2; host->check_int = check_int_v1_v2; + if (cpu_is_mx21()) + host->irq_control = irq_control_mx21; + else + host->irq_control = irq_control_v1_v2; } if (nfc_is_v21()) { @@ -1062,6 +1115,7 @@ static int __init mxcnd_probe(struct platform_device *pdev) host->send_read_id = send_read_id_v3; host->check_int = check_int_v3; host->get_dev_status = get_dev_status_v3; + host->irq_control = irq_control_v3; oob_smallpage = &nandv2_hw_eccoob_smallpage; oob_largepage = &nandv2_hw_eccoob_largepage; } else @@ -1093,14 +1147,34 @@ static int __init mxcnd_probe(struct platform_device *pdev) this->options |= NAND_USE_FLASH_BBT; } - init_waitqueue_head(&host->irq_waitq); + init_completion(&host->op_completion); host->irq = platform_get_irq(pdev, 0); + /* + * mask the interrupt. For i.MX21 explicitely call + * irq_control_v1_v2 to use the mask bit. We can't call + * disable_irq_nosync() for an interrupt we do not own yet. + */ + if (cpu_is_mx21()) + irq_control_v1_v2(host, 0); + else + host->irq_control(host, 0); + err = request_irq(host->irq, mxc_nfc_irq, IRQF_DISABLED, DRIVER_NAME, host); if (err) goto eirq; + host->irq_control(host, 0); + + /* + * Now that the interrupt is disabled make sure the interrupt + * mask bit is cleared on i.MX21. Otherwise we can't read + * the interrupt status bit on this machine. + */ + if (cpu_is_mx21()) + irq_control_v1_v2(host, 1); + /* first scan to find the device and get the page size */ if (nand_scan_ident(mtd, 1, NULL)) { err = -ENXIO; diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index 439e80d78edd..cd41c58b5bbd 100644 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -413,7 +413,7 @@ static inline int omap_nand_dma_transfer(struct mtd_info *mtd, void *addr, prefetch_status = gpmc_read_status(GPMC_PREFETCH_COUNT); } while (prefetch_status); /* disable and stop the PFPW engine */ - gpmc_prefetch_reset(); + gpmc_prefetch_reset(info->gpmc_cs); dma_unmap_single(&info->pdev->dev, dma_addr, len, dir); return 0; |
