diff options
Diffstat (limited to 'drivers/mtd/nand/tx4938ndfmc.c')
| -rw-r--r-- | drivers/mtd/nand/tx4938ndfmc.c | 406 |
1 files changed, 0 insertions, 406 deletions
diff --git a/drivers/mtd/nand/tx4938ndfmc.c b/drivers/mtd/nand/tx4938ndfmc.c deleted file mode 100644 index df26e58820b3..000000000000 --- a/drivers/mtd/nand/tx4938ndfmc.c +++ /dev/null @@ -1,406 +0,0 @@ -/* - * drivers/mtd/nand/tx4938ndfmc.c - * - * Overview: - * This is a device driver for the NAND flash device connected to - * TX4938 internal NAND Memory Controller. - * TX4938 NDFMC is almost same as TX4925 NDFMC, but register size are 64 bit. - * - * Author: source@mvista.com - * - * Based on spia.c by Steven J. Hill - * - * $Id: tx4938ndfmc.c,v 1.4 2004/10/05 13:50:20 gleixner Exp $ - * - * Copyright (C) 2000-2001 Toshiba Corporation - * - * 2003 (c) MontaVista Software, Inc. This file is licensed under the - * terms of the GNU General Public License version 2. This program is - * licensed "as is" without any warranty of any kind, whether express - * or implied. - */ -#include <linux/config.h> -#include <linux/slab.h> -#include <linux/init.h> -#include <linux/module.h> -#include <linux/mtd/mtd.h> -#include <linux/mtd/nand.h> -#include <linux/mtd/nand_ecc.h> -#include <linux/mtd/partitions.h> -#include <asm/io.h> -#include <asm/bootinfo.h> -#include <linux/delay.h> -#include <asm/tx4938/rbtx4938.h> - -extern struct nand_oobinfo jffs2_oobinfo; - -/* - * MTD structure for TX4938 NDFMC - */ -static struct mtd_info *tx4938ndfmc_mtd; - -/* - * Define partitions for flash device - */ -#define flush_wb() (void)tx4938_ndfmcptr->mcr; - -#define NUM_PARTITIONS 3 -#define NUMBER_OF_CIS_BLOCKS 24 -#define SIZE_OF_BLOCK 0x00004000 -#define NUMBER_OF_BLOCK_PER_ZONE 1024 -#define SIZE_OF_ZONE (NUMBER_OF_BLOCK_PER_ZONE * SIZE_OF_BLOCK) -#ifndef CONFIG_MTD_CMDLINE_PARTS -/* - * You can use the following sample of MTD partitions - * on the NAND Flash Memory 32MB or more. - * - * The following figure shows the image of the sample partition on - * the 32MB NAND Flash Memory. - * - * Block No. - * 0 +-----------------------------+ ------ - * | CIS | ^ - * 24 +-----------------------------+ | - * | kernel image | | Zone 0 - * | | | - * +-----------------------------+ | - * 1023 | unused area | v - * +-----------------------------+ ------ - * 1024 | JFFS2 | ^ - * | | | - * | | | Zone 1 - * | | | - * | | | - * | | v - * 2047 +-----------------------------+ ------ - * - */ -static struct mtd_partition partition_info[NUM_PARTITIONS] = { - { - .name = "RBTX4938 CIS Area", - .offset = 0, - .size = (NUMBER_OF_CIS_BLOCKS * SIZE_OF_BLOCK), - .mask_flags = MTD_WRITEABLE /* This partition is NOT writable */ - }, - { - .name = "RBTX4938 kernel image", - .offset = MTDPART_OFS_APPEND, - .size = 8 * 0x00100000, /* 8MB (Depends on size of kernel image) */ - .mask_flags = MTD_WRITEABLE /* This partition is NOT writable */ - }, - { - .name = "Root FS (JFFS2)", - .offset = (0 + SIZE_OF_ZONE), /* start address of next zone */ - .size = MTDPART_SIZ_FULL - }, -}; -#endif - -static void tx4938ndfmc_hwcontrol(struct mtd_info *mtd, int cmd) -{ - switch (cmd) { - case NAND_CTL_SETCLE: - tx4938_ndfmcptr->mcr |= TX4938_NDFMCR_CLE; - break; - case NAND_CTL_CLRCLE: - tx4938_ndfmcptr->mcr &= ~TX4938_NDFMCR_CLE; - break; - case NAND_CTL_SETALE: - tx4938_ndfmcptr->mcr |= TX4938_NDFMCR_ALE; - break; - case NAND_CTL_CLRALE: - tx4938_ndfmcptr->mcr &= ~TX4938_NDFMCR_ALE; - break; - /* TX4938_NDFMCR_CE bit is 0:high 1:low */ - case NAND_CTL_SETNCE: - tx4938_ndfmcptr->mcr |= TX4938_NDFMCR_CE; - break; - case NAND_CTL_CLRNCE: - tx4938_ndfmcptr->mcr &= ~TX4938_NDFMCR_CE; - break; - case NAND_CTL_SETWP: - tx4938_ndfmcptr->mcr |= TX4938_NDFMCR_WE; - break; - case NAND_CTL_CLRWP: - tx4938_ndfmcptr->mcr &= ~TX4938_NDFMCR_WE; - break; - } -} -static int tx4938ndfmc_dev_ready(struct mtd_info *mtd) -{ - flush_wb(); - return !(tx4938_ndfmcptr->sr & TX4938_NDFSR_BUSY); -} -static void tx4938ndfmc_calculate_ecc(struct mtd_info *mtd, const u_char *dat, u_char *ecc_code) -{ - u32 mcr = tx4938_ndfmcptr->mcr; - mcr &= ~TX4938_NDFMCR_ECC_ALL; - tx4938_ndfmcptr->mcr = mcr | TX4938_NDFMCR_ECC_OFF; - tx4938_ndfmcptr->mcr = mcr | TX4938_NDFMCR_ECC_READ; - ecc_code[1] = tx4938_ndfmcptr->dtr; - ecc_code[0] = tx4938_ndfmcptr->dtr; - ecc_code[2] = tx4938_ndfmcptr->dtr; - tx4938_ndfmcptr->mcr = mcr | TX4938_NDFMCR_ECC_OFF; -} -static void tx4938ndfmc_enable_hwecc(struct mtd_info *mtd, int mode) -{ - u32 mcr = tx4938_ndfmcptr->mcr; - mcr &= ~TX4938_NDFMCR_ECC_ALL; - tx4938_ndfmcptr->mcr = mcr | TX4938_NDFMCR_ECC_RESET; - tx4938_ndfmcptr->mcr = mcr | TX4938_NDFMCR_ECC_OFF; - tx4938_ndfmcptr->mcr = mcr | TX4938_NDFMCR_ECC_ON; -} - -static u_char tx4938ndfmc_nand_read_byte(struct mtd_info *mtd) -{ - struct nand_chip *this = mtd->priv; - return tx4938_read_nfmc(this->IO_ADDR_R); -} - -static void tx4938ndfmc_nand_write_byte(struct mtd_info *mtd, u_char byte) -{ - struct nand_chip *this = mtd->priv; - tx4938_write_nfmc(byte, this->IO_ADDR_W); -} - -static void tx4938ndfmc_nand_write_buf(struct mtd_info *mtd, const u_char *buf, int len) -{ - int i; - struct nand_chip *this = mtd->priv; - - for (i=0; i<len; i++) - tx4938_write_nfmc(buf[i], this->IO_ADDR_W); -} - -static void tx4938ndfmc_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len) -{ - int i; - struct nand_chip *this = mtd->priv; - - for (i=0; i<len; i++) - buf[i] = tx4938_read_nfmc(this->IO_ADDR_R); -} - -static int tx4938ndfmc_nand_verify_buf(struct mtd_info *mtd, const u_char *buf, int len) -{ - int i; - struct nand_chip *this = mtd->priv; - - for (i=0; i<len; i++) - if (buf[i] != tx4938_read_nfmc(this->IO_ADDR_R)) - return -EFAULT; - - return 0; -} - -/* - * Send command to NAND device - */ -static void tx4938ndfmc_nand_command (struct mtd_info *mtd, unsigned command, int column, int page_addr) -{ - register struct nand_chip *this = mtd->priv; - - /* Begin command latch cycle */ - this->hwcontrol(mtd, NAND_CTL_SETCLE); - /* - * Write out the command to the device. - */ - if (command == NAND_CMD_SEQIN) { - int readcmd; - - if (column >= mtd->oobblock) { - /* OOB area */ - column -= mtd->oobblock; - readcmd = NAND_CMD_READOOB; - } else if (column < 256) { - /* First 256 bytes --> READ0 */ - readcmd = NAND_CMD_READ0; - } else { - column -= 256; - readcmd = NAND_CMD_READ1; - } - this->write_byte(mtd, readcmd); - } - this->write_byte(mtd, command); - - /* Set ALE and clear CLE to start address cycle */ - this->hwcontrol(mtd, NAND_CTL_CLRCLE); - - if (column != -1 || page_addr != -1) { - this->hwcontrol(mtd, NAND_CTL_SETALE); - - /* Serially input address */ - if (column != -1) - this->write_byte(mtd, column); - if (page_addr != -1) { - this->write_byte(mtd, (unsigned char) (page_addr & 0xff)); - this->write_byte(mtd, (unsigned char) ((page_addr >> 8) & 0xff)); - /* One more address cycle for higher density devices */ - if (mtd->size & 0x0c000000) - this->write_byte(mtd, (unsigned char) ((page_addr >> 16) & 0x0f)); - } - /* Latch in address */ - this->hwcontrol(mtd, NAND_CTL_CLRALE); - } - - /* - * program and erase have their own busy handlers - * status and sequential in needs no delay - */ - switch (command) { - - case NAND_CMD_PAGEPROG: - /* Turn off WE */ - this->hwcontrol (mtd, NAND_CTL_CLRWP); - return; - - case NAND_CMD_SEQIN: - /* Turn on WE */ - this->hwcontrol (mtd, NAND_CTL_SETWP); - return; - - case NAND_CMD_ERASE1: - case NAND_CMD_ERASE2: - case NAND_CMD_STATUS: - return; - - case NAND_CMD_RESET: - if (this->dev_ready) - break; - this->hwcontrol(mtd, NAND_CTL_SETCLE); - this->write_byte(mtd, NAND_CMD_STATUS); - this->hwcontrol(mtd, NAND_CTL_CLRCLE); - while ( !(this->read_byte(mtd) & 0x40)); - return; - - /* This applies to read commands */ - default: - /* - * If we don't have access to the busy pin, we apply the given - * command delay - */ - if (!this->dev_ready) { - udelay (this->chip_delay); - return; - } - } - - /* wait until command is processed */ - while (!this->dev_ready(mtd)); -} - -#ifdef CONFIG_MTD_CMDLINE_PARTS -extern int parse_cmdline_partitions(struct mtd_info *master, struct mtd_partition **pparts, char *); -#endif -/* - * Main initialization routine - */ -int __init tx4938ndfmc_init (void) -{ - struct nand_chip *this; - int bsprt = 0, hold = 0xf, spw = 0xf; - int protected = 0; - - if ((*rbtx4938_piosel_ptr & 0x0c) != 0x08) { - printk("TX4938 NDFMC: disabled by IOC PIOSEL\n"); - return -ENODEV; - } - bsprt = 1; - hold = 2; - spw = 9 - 1; /* 8 GBUSCLK = 80ns (@ GBUSCLK 100MHz) */ - - if ((tx4938_ccfgptr->pcfg & - (TX4938_PCFG_ATA_SEL|TX4938_PCFG_ISA_SEL|TX4938_PCFG_NDF_SEL)) - != TX4938_PCFG_NDF_SEL) { - printk("TX4938 NDFMC: disabled by PCFG.\n"); - return -ENODEV; - } - - /* reset NDFMC */ - tx4938_ndfmcptr->rstr |= TX4938_NDFRSTR_RST; - while (tx4938_ndfmcptr->rstr & TX4938_NDFRSTR_RST) - ; - /* setup BusSeparete, Hold Time, Strobe Pulse Width */ - tx4938_ndfmcptr->mcr = bsprt ? TX4938_NDFMCR_BSPRT : 0; - tx4938_ndfmcptr->spr = hold << 4 | spw; - - /* Allocate memory for MTD device structure and private data */ - tx4938ndfmc_mtd = kmalloc (sizeof(struct mtd_info) + sizeof (struct nand_chip), - GFP_KERNEL); - if (!tx4938ndfmc_mtd) { - printk ("Unable to allocate TX4938 NDFMC MTD device structure.\n"); - return -ENOMEM; - } - - /* Get pointer to private data */ - this = (struct nand_chip *) (&tx4938ndfmc_mtd[1]); - - /* Initialize structures */ - memset((char *) tx4938ndfmc_mtd, 0, sizeof(struct mtd_info)); - memset((char *) this, 0, sizeof(struct nand_chip)); - - /* Link the private data with the MTD structure */ - tx4938ndfmc_mtd->priv = this; - - /* Set address of NAND IO lines */ - this->IO_ADDR_R = (unsigned long)&tx4938_ndfmcptr->dtr; - this->IO_ADDR_W = (unsigned long)&tx4938_ndfmcptr->dtr; - this->hwcontrol = tx4938ndfmc_hwcontrol; - this->dev_ready = tx4938ndfmc_dev_ready; - this->calculate_ecc = tx4938ndfmc_calculate_ecc; - this->correct_data = nand_correct_data; - this->enable_hwecc = tx4938ndfmc_enable_hwecc; - this->eccmode = NAND_ECC_HW3_256; - this->chip_delay = 100; - this->read_byte = tx4938ndfmc_nand_read_byte; - this->write_byte = tx4938ndfmc_nand_write_byte; - this->cmdfunc = tx4938ndfmc_nand_command; - this->write_buf = tx4938ndfmc_nand_write_buf; - this->read_buf = tx4938ndfmc_nand_read_buf; - this->verify_buf = tx4938ndfmc_nand_verify_buf; - - /* Scan to find existance of the device */ - if (nand_scan (tx4938ndfmc_mtd, 1)) { - kfree (tx4938ndfmc_mtd); - return -ENXIO; - } - - if (protected) { - printk(KERN_INFO "TX4938 NDFMC: write protected.\n"); - tx4938ndfmc_mtd->flags &= ~(MTD_WRITEABLE | MTD_ERASEABLE); - } - -#ifdef CONFIG_MTD_CMDLINE_PARTS - { - int mtd_parts_nb = 0; - struct mtd_partition *mtd_parts = 0; - mtd_parts_nb = parse_cmdline_partitions(tx4938ndfmc_mtd, &mtd_parts, "tx4938ndfmc"); - if (mtd_parts_nb > 0) - add_mtd_partitions(tx4938ndfmc_mtd, mtd_parts, mtd_parts_nb); - else - add_mtd_device(tx4938ndfmc_mtd); - } -#else - add_mtd_partitions(tx4938ndfmc_mtd, partition_info, NUM_PARTITIONS ); -#endif - - return 0; -} -module_init(tx4938ndfmc_init); - -/* - * Clean up routine - */ -static void __exit tx4938ndfmc_cleanup (void) -{ - /* Release resources, unregister device */ - nand_release (tx4938ndfmc_mtd); - - /* Free the MTD device structure */ - kfree (tx4938ndfmc_mtd); -} -module_exit(tx4938ndfmc_cleanup); - -MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Alice Hennessy <ahennessy@mvista.com>"); -MODULE_DESCRIPTION("Board-specific glue layer for NAND flash on TX4938 NDFMC"); |
