diff options
Diffstat (limited to 'drivers/mmc/host')
| -rw-r--r-- | drivers/mmc/host/Kconfig | 30 | ||||
| -rw-r--r-- | drivers/mmc/host/Makefile | 2 | ||||
| -rw-r--r-- | drivers/mmc/host/at91_mci.c | 25 | ||||
| -rw-r--r-- | drivers/mmc/host/au1xmmc.c | 58 | ||||
| -rw-r--r-- | drivers/mmc/host/imxmmc.c | 32 | ||||
| -rw-r--r-- | drivers/mmc/host/mmc_spi.c | 1408 | ||||
| -rw-r--r-- | drivers/mmc/host/mmci.c | 21 | ||||
| -rw-r--r-- | drivers/mmc/host/omap.c | 12 | ||||
| -rw-r--r-- | drivers/mmc/host/pxamci.c | 71 | ||||
| -rw-r--r-- | drivers/mmc/host/pxamci.h | 2 | ||||
| -rw-r--r-- | drivers/mmc/host/ricoh_mmc.c | 151 | ||||
| -rw-r--r-- | drivers/mmc/host/sdhci.c | 127 | ||||
| -rw-r--r-- | drivers/mmc/host/sdhci.h | 2 | ||||
| -rw-r--r-- | drivers/mmc/host/tifm_sd.c | 32 | ||||
| -rw-r--r-- | drivers/mmc/host/wbsd.c | 43 |
15 files changed, 1860 insertions, 156 deletions
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index e23082fe88d0..5fef6783c716 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -35,6 +35,23 @@ config MMC_SDHCI If unsure, say N. +config MMC_RICOH_MMC + tristate "Ricoh MMC Controller Disabler (EXPERIMENTAL)" + depends on PCI && EXPERIMENTAL && MMC_SDHCI + help + This selects the disabler for the Ricoh MMC Controller. This + proprietary controller is unnecessary because the SDHCI driver + supports MMC cards on the SD controller, but if it is not + disabled, it will steal the MMC cards away - rendering them + useless. It is safe to select this driver even if you don't + have a Ricoh based card reader. + + + To compile this driver as a module, choose M here: + the module will be called ricoh_mmc. + + If unsure, say Y. + config MMC_OMAP tristate "TI OMAP Multimedia Card Interface support" depends on ARCH_OMAP @@ -100,3 +117,16 @@ config MMC_TIFM_SD To compile this driver as a module, choose M here: the module will be called tifm_sd. +config MMC_SPI + tristate "MMC/SD over SPI (EXPERIMENTAL)" + depends on MMC && SPI_MASTER && !HIGHMEM && EXPERIMENTAL + select CRC7 + select CRC_ITU_T + help + Some systems accss MMC/SD cards using a SPI controller instead of + using a "native" MMC/SD controller. This has a disadvantage of + being relatively high overhead, but a compensating advantage of + working on many systems without dedicated MMC/SD controllers. + + If unsure, or if your system has no SPI master driver, say N. + diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile index 6685f64345b4..3877c87e6da2 100644 --- a/drivers/mmc/host/Makefile +++ b/drivers/mmc/host/Makefile @@ -10,9 +10,11 @@ obj-$(CONFIG_MMC_ARMMMCI) += mmci.o obj-$(CONFIG_MMC_PXA) += pxamci.o obj-$(CONFIG_MMC_IMX) += imxmmc.o obj-$(CONFIG_MMC_SDHCI) += sdhci.o +obj-$(CONFIG_MMC_RICOH_MMC) += ricoh_mmc.o obj-$(CONFIG_MMC_WBSD) += wbsd.o obj-$(CONFIG_MMC_AU1X) += au1xmmc.o obj-$(CONFIG_MMC_OMAP) += omap.o obj-$(CONFIG_MMC_AT91) += at91_mci.o obj-$(CONFIG_MMC_TIFM_SD) += tifm_sd.o +obj-$(CONFIG_MMC_SPI) += mmc_spi.o diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index 955ea60583b5..6ba98a49612d 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -328,7 +328,7 @@ static void at91_mci_handle_transmitted(struct at91mci_host *host) data = cmd->data; if (!data) return; - if (cmd->data->flags & MMC_DATA_MULTI) { + if (cmd->data->blocks > 1) { pr_debug("multiple write : wait for BLKE...\n"); at91_mci_write(host, AT91_MCI_IER, AT91_MCI_BLKE); } else @@ -428,6 +428,14 @@ static void at91_mci_send_command(struct at91mci_host *host, struct mmc_command } if (data) { + + if ( data->blksz & 0x3 ) { + pr_debug("Unsupported block size\n"); + cmd->error = -EINVAL; + mmc_request_done(host->mmc, host->request); + return; + } + block_length = data->blksz; blocks = data->blocks; @@ -439,7 +447,7 @@ static void at91_mci_send_command(struct at91mci_host *host, struct mmc_command if (data->flags & MMC_DATA_STREAM) cmdr |= AT91_MCI_TRTYP_STREAM; - if (data->flags & MMC_DATA_MULTI) + if (data->blocks > 1) cmdr |= AT91_MCI_TRTYP_MULTIPLE; } else { @@ -577,24 +585,22 @@ static void at91_mci_completed_command(struct at91mci_host *host) AT91_MCI_RENDE | AT91_MCI_RTOE | AT91_MCI_DCRCE | AT91_MCI_DTOE | AT91_MCI_OVRE | AT91_MCI_UNRE)) { if ((status & AT91_MCI_RCRCE) && !(mmc_resp_type(cmd) & MMC_RSP_CRC)) { - cmd->error = MMC_ERR_NONE; + cmd->error = 0; } else { if (status & (AT91_MCI_RTOE | AT91_MCI_DTOE)) - cmd->error = MMC_ERR_TIMEOUT; + cmd->error = -ETIMEDOUT; else if (status & (AT91_MCI_RCRCE | AT91_MCI_DCRCE)) - cmd->error = MMC_ERR_BADCRC; - else if (status & (AT91_MCI_OVRE | AT91_MCI_UNRE)) - cmd->error = MMC_ERR_FIFO; + cmd->error = -EILSEQ; else - cmd->error = MMC_ERR_FAILED; + cmd->error = -EIO; pr_debug("Error detected and set to %d (cmd = %d, retries = %d)\n", cmd->error, cmd->opcode, cmd->retries); } } else - cmd->error = MMC_ERR_NONE; + cmd->error = 0; at91_mci_process_next(host); } @@ -836,7 +842,6 @@ static int __init at91_mci_probe(struct platform_device *pdev) mmc->f_min = 375000; mmc->f_max = 25000000; mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; - mmc->caps = MMC_CAP_BYTEBLOCK; mmc->max_blk_size = 4095; mmc->max_blk_count = mmc->max_req_size; diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c index 34c99d4ea041..92c4d0dfee43 100644 --- a/drivers/mmc/host/au1xmmc.c +++ b/drivers/mmc/host/au1xmmc.c @@ -186,7 +186,7 @@ static void au1xmmc_tasklet_finish(unsigned long param) } static int au1xmmc_send_command(struct au1xmmc_host *host, int wait, - struct mmc_command *cmd, unsigned int flags) + struct mmc_command *cmd, struct mmc_data *data) { u32 mmccmd = (cmd->opcode << SD_CMD_CI_SHIFT); @@ -208,19 +208,21 @@ static int au1xmmc_send_command(struct au1xmmc_host *host, int wait, default: printk(KERN_INFO "au1xmmc: unhandled response type %02x\n", mmc_resp_type(cmd)); - return MMC_ERR_INVALID; + return -EINVAL; } - if (flags & MMC_DATA_READ) { - if (flags & MMC_DATA_MULTI) - mmccmd |= SD_CMD_CT_4; - else - mmccmd |= SD_CMD_CT_2; - } else if (flags & MMC_DATA_WRITE) { - if (flags & MMC_DATA_MULTI) - mmccmd |= SD_CMD_CT_3; - else - mmccmd |= SD_CMD_CT_1; + if (data) { + if (flags & MMC_DATA_READ) { + if (data->blocks > 1) + mmccmd |= SD_CMD_CT_4; + else + mmccmd |= SD_CMD_CT_2; + } else if (flags & MMC_DATA_WRITE) { + if (data->blocks > 1) + mmccmd |= SD_CMD_CT_3; + else + mmccmd |= SD_CMD_CT_1; + } } au_writel(cmd->arg, HOST_CMDARG(host)); @@ -253,7 +255,7 @@ static int au1xmmc_send_command(struct au1xmmc_host *host, int wait, IRQ_ON(host, SD_CONFIG_CR); } - return MMC_ERR_NONE; + return 0; } static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status) @@ -278,7 +280,7 @@ static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status) while((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB)) status = au_readl(HOST_STATUS(host)); - data->error = MMC_ERR_NONE; + data->error = 0; dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, host->dma.dir); /* Process any errors */ @@ -288,14 +290,14 @@ static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status) crc |= ((status & 0x07) == 0x02) ? 0 : 1; if (crc) - data->error = MMC_ERR_BADCRC; + data->error = -EILSEQ; /* Clear the CRC bits */ au_writel(SD_STATUS_WC | SD_STATUS_RC, HOST_STATUS(host)); data->bytes_xfered = 0; - if (data->error == MMC_ERR_NONE) { + if (!data->error) { if (host->flags & HOST_F_DMA) { u32 chan = DMA_CHANNEL(host); @@ -475,7 +477,7 @@ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) return; cmd = mrq->cmd; - cmd->error = MMC_ERR_NONE; + cmd->error = 0; if (cmd->flags & MMC_RSP_PRESENT) { if (cmd->flags & MMC_RSP_136) { @@ -512,11 +514,11 @@ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) /* Figure out errors */ if (status & (SD_STATUS_SC | SD_STATUS_WC | SD_STATUS_RC)) - cmd->error = MMC_ERR_BADCRC; + cmd->error = -EILSEQ; trans = host->flags & (HOST_F_XMIT | HOST_F_RECV); - if (!trans || cmd->error != MMC_ERR_NONE) { + if (!trans || cmd->error) { IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA|SD_CONFIG_RF); tasklet_schedule(&host->finish_task); @@ -589,7 +591,7 @@ au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) data->sg_len, host->dma.dir); if (host->dma.len == 0) - return MMC_ERR_TIMEOUT; + return -ETIMEDOUT; au_writel(data->blksz - 1, HOST_BLKSIZE(host)); @@ -640,11 +642,11 @@ au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) //IRQ_ON(host, SD_CONFIG_RA|SD_CONFIG_RF); } - return MMC_ERR_NONE; + return 0; dataerr: dma_unmap_sg(mmc_dev(host->mmc),data->sg,data->sg_len,host->dma.dir); - return MMC_ERR_TIMEOUT; + return -ETIMEDOUT; } /* static void au1xmmc_request @@ -656,7 +658,7 @@ static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq) struct au1xmmc_host *host = mmc_priv(mmc); unsigned int flags = 0; - int ret = MMC_ERR_NONE; + int ret = 0; WARN_ON(irqs_disabled()); WARN_ON(host->status != HOST_S_IDLE); @@ -672,10 +674,10 @@ static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq) ret = au1xmmc_prepare_data(host, mrq->data); } - if (ret == MMC_ERR_NONE) - ret = au1xmmc_send_command(host, 0, mrq->cmd, flags); + if (!ret) + ret = au1xmmc_send_command(host, 0, mrq->cmd, mrq->data); - if (ret != MMC_ERR_NONE) { + if (ret) { mrq->cmd->error = ret; au1xmmc_finish_request(host); } @@ -764,10 +766,10 @@ static irqreturn_t au1xmmc_irq(int irq, void *dev_id) if (host->mrq && (status & STATUS_TIMEOUT)) { if (status & SD_STATUS_RAT) - host->mrq->cmd->error = MMC_ERR_TIMEOUT; + host->mrq->cmd->error = -ETIMEDOUT; else if (status & SD_STATUS_DT) - host->mrq->data->error = MMC_ERR_TIMEOUT; + host->mrq->data->error = -ETIMEDOUT; /* In PIO mode, interrupts might still be enabled */ IRQ_OFF(host, SD_CONFIG_NE | SD_CONFIG_TH); diff --git a/drivers/mmc/host/imxmmc.c b/drivers/mmc/host/imxmmc.c index 54bfc9f25596..6ebc41e7592c 100644 --- a/drivers/mmc/host/imxmmc.c +++ b/drivers/mmc/host/imxmmc.c @@ -428,11 +428,11 @@ static int imxmci_finish_data(struct imxmci_host *host, unsigned int stat) if ( stat & STATUS_ERR_MASK ) { dev_dbg(mmc_dev(host->mmc), "request failed. status: 0x%08x\n",stat); if(stat & (STATUS_CRC_READ_ERR | STATUS_CRC_WRITE_ERR)) - data->error = MMC_ERR_BADCRC; + data->error = -EILSEQ; else if(stat & STATUS_TIME_OUT_READ) - data->error = MMC_ERR_TIMEOUT; + data->error = -ETIMEDOUT; else - data->error = MMC_ERR_FAILED; + data->error = -EIO; } else { data->bytes_xfered = host->dma_size; } @@ -458,10 +458,10 @@ static int imxmci_cmd_done(struct imxmci_host *host, unsigned int stat) if (stat & STATUS_TIME_OUT_RESP) { dev_dbg(mmc_dev(host->mmc), "CMD TIMEOUT\n"); - cmd->error = MMC_ERR_TIMEOUT; + cmd->error = -ETIMEDOUT; } else if (stat & STATUS_RESP_CRC_ERR && cmd->flags & MMC_RSP_CRC) { dev_dbg(mmc_dev(host->mmc), "cmd crc error\n"); - cmd->error = MMC_ERR_BADCRC; + cmd->error = -EILSEQ; } if(cmd->flags & MMC_RSP_PRESENT) { @@ -482,7 +482,7 @@ static int imxmci_cmd_done(struct imxmci_host *host, unsigned int stat) dev_dbg(mmc_dev(host->mmc), "RESP 0x%08x, 0x%08x, 0x%08x, 0x%08x, error %d\n", cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3], cmd->error); - if (data && (cmd->error == MMC_ERR_NONE) && !(stat & STATUS_ERR_MASK)) { + if (data && !cmd->error && !(stat & STATUS_ERR_MASK)) { if (host->req->data->flags & MMC_DATA_WRITE) { /* Wait for FIFO to be empty before starting DMA write */ @@ -491,7 +491,7 @@ static int imxmci_cmd_done(struct imxmci_host *host, unsigned int stat) if(imxmci_busy_wait_for_status(host, &stat, STATUS_APPL_BUFF_FE, 40, "imxmci_cmd_done DMA WR") < 0) { - cmd->error = MMC_ERR_FIFO; + cmd->error = -EIO; imxmci_finish_data(host, stat); if(host->req) imxmci_finish_request(host, host->req); @@ -884,9 +884,21 @@ static void imxmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) } } +static int imxmci_get_ro(struct mmc_host *mmc) +{ + struct imxmci_host *host = mmc_priv(mmc); + + if (host->pdata && host->pdata->get_ro) + return host->pdata->get_ro(mmc_dev(mmc)); + /* Host doesn't support read only detection so assume writeable */ + return 0; +} + + static const struct mmc_host_ops imxmci_ops = { .request = imxmci_request, .set_ios = imxmci_set_ios, + .get_ro = imxmci_get_ro, }; static struct resource *platform_device_resource(struct platform_device *dev, unsigned int mask, int nr) @@ -913,7 +925,7 @@ static void imxmci_check_status(unsigned long data) { struct imxmci_host *host = (struct imxmci_host *)data; - if( host->pdata->card_present() != host->present ) { + if( host->pdata->card_present(mmc_dev(host->mmc)) != host->present ) { host->present ^= 1; dev_info(mmc_dev(host->mmc), "card %s\n", host->present ? "inserted" : "removed"); @@ -963,7 +975,7 @@ static int imxmci_probe(struct platform_device *pdev) mmc->f_min = 150000; mmc->f_max = CLK_RATE/2; mmc->ocr_avail = MMC_VDD_32_33; - mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_BYTEBLOCK; + mmc->caps = MMC_CAP_4_BIT_DATA; /* MMC core transfer sizes tunable parameters */ mmc->max_hw_segs = 64; @@ -1022,7 +1034,7 @@ static int imxmci_probe(struct platform_device *pdev) if (ret) goto out; - host->present = host->pdata->card_present(); + host->present = host->pdata->card_present(mmc_dev(mmc)); init_timer(&host->timer); host->timer.data = (unsigned long)host; host->timer.function = imxmci_check_status; diff --git a/drivers/mmc/host/mmc_spi.c b/drivers/mmc/host/mmc_spi.c new file mode 100644 index 000000000000..f30327bba6f6 --- /dev/null +++ b/drivers/mmc/host/mmc_spi.c @@ -0,0 +1,1408 @@ +/* + * mmc_spi.c - Access SD/MMC cards through SPI master controllers + * + * (C) Copyright 2005, Intec Automation, + * Mike Lavender (mike@steroidmicros) + * (C) Copyright 2006-2007, David Brownell + * (C) Copyright 2007, Axis Communications, + * Hans-Peter Nilsson (hp@axis.com) + * (C) Copyright 2007, ATRON electronic GmbH, + * Jan Nikitenko <jan.nikitenko@gmail.com> + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#include <linux/hrtimer.h> +#include <linux/delay.h> +#include <linux/blkdev.h> +#include <linux/dma-mapping.h> +#include <linux/crc7.h> +#include <linux/crc-itu-t.h> + +#include <linux/mmc/host.h> +#include <linux/mmc/mmc.h> /* for R1_SPI_* bit values */ + +#include <linux/spi/spi.h> +#include <linux/spi/mmc_spi.h> + +#include <asm/unaligned.h> + + +/* NOTES: + * + * - For now, we won't try to interoperate with a real mmc/sd/sdio + * controller, although some of them do have hardware support for + * SPI protocol. The main reason for such configs would be mmc-ish + * cards like DataFlash, which don't support that "native" protocol. + * + * We don't have a "DataFlash/MMC/SD/SDIO card slot" abstraction to + * switch between driver stacks, and in any case if "native" mode + * is available, it will be faster and hence preferable. + * + * - MMC depends on a different chipselect management policy than the + * SPI interface currently supports for shared bus segments: it needs + * to issue multiple spi_message requests with the chipselect active, + * using the results of one message to decide the next one to issue. + * + * Pending updates to the programming interface, this driver expects + * that it not share the bus with other drivers (precluding conflicts). + * + * - We tell the controller to keep the chipselect active from the + * beginning of an mmc_host_ops.request until the end. So beware + * of SPI controller drivers that mis-handle the cs_change flag! + * + * However, many cards seem OK with chipselect flapping up/down + * during that time ... at least on unshared bus segments. + */ + + +/* + * Local protocol constants, internal to data block protocols. + */ + +/* Response tokens used to ack each block written: */ +#define SPI_MMC_RESPONSE_CODE(x) ((x) & 0x1f) +#define SPI_RESPONSE_ACCEPTED ((2 << 1)|1) +#define SPI_RESPONSE_CRC_ERR ((5 << 1)|1) +#define SPI_RESPONSE_WRITE_ERR ((6 << 1)|1) + +/* Read and write blocks start with these tokens and end with crc; + * on error, read tokens act like a subset of R2_SPI_* values. + */ +#define SPI_TOKEN_SINGLE 0xfe /* single block r/w, multiblock read */ +#define SPI_TOKEN_MULTI_WRITE 0xfc /* multiblock write */ +#define SPI_TOKEN_STOP_TRAN 0xfd /* terminate multiblock write */ + +#define MMC_SPI_BLOCKSIZE 512 + + +/* These fixed timeouts come from the latest SD specs, which say to ignore + * the CSD values. The R1B value is for card erase (e.g. the "I forgot the + * card's password" scenario); it's mostly applied to STOP_TRANSMISSION after + * reads which takes nowhere near that long. Older cards may be able to use + * shorter timeouts ... but why bother? + */ +#define readblock_timeout ktime_set(0, 100 * 1000 * 1000) +#define writeblock_timeout ktime_set(0, 250 * 1000 * 1000) +#define r1b_timeout ktime_set(3, 0) + + +/****************************************************************************/ + +/* + * Local Data Structures + */ + +/* "scratch" is per-{command,block} data exchanged with the card */ +struct scratch { + u8 status[29]; + u8 data_token; + __be16 crc_val; +}; + +struct mmc_spi_host { + struct mmc_host *mmc; + struct spi_device *spi; + + unsigned char power_mode; + u16 powerup_msecs; + + struct mmc_spi_platform_data *pdata; + + /* for bulk data transfers */ + struct spi_transfer token, t, crc, early_status; + struct spi_message m; + + /* for status readback */ + struct spi_transfer status; + struct spi_message readback; + + /* underlying DMA-aware controller, or null */ + struct device *dma_dev; + + /* buffer used for commands and for message "overhead" */ + struct scratch *data; + dma_addr_t data_dma; + + /* Specs say to write ones most of the time, even when the card + * has no need to read its input data; and many cards won't care. + * This is our source of those ones. + */ + void *ones; + dma_addr_t ones_dma; +}; + + +/****************************************************************************/ + +/* + * MMC-over-SPI protocol glue, used by the MMC stack interface + */ + +static inline int mmc_cs_off(struct mmc_spi_host *host) +{ + /* chipselect will always be inactive after setup() */ + return spi_setup(host->spi); +} + +static int +mmc_spi_readbytes(struct mmc_spi_host *host, unsigned len) +{ + int status; + + if (len > sizeof(*host->data)) { + WARN_ON(1); + return -EIO; + } + + host->status.len = len; + + if (host->dma_dev) + dma_sync_single_for_device(host->dma_dev, + host->data_dma, sizeof(*host->data), + DMA_FROM_DEVICE); + + status = spi_sync(host->spi, &host->readback); + if (status == 0) + status = host->readback.status; + + if (host->dma_dev) + dma_sync_single_for_cpu(host->dma_dev, + host->data_dma, sizeof(*host->data), + DMA_FROM_DEVICE); + + return status; +} + +static int +mmc_spi_skip(struct mmc_spi_host *host, ktime_t timeout, unsigned n, u8 byte) +{ + u8 *cp = host->data->status; + + timeout = ktime_add(timeout, ktime_get()); + + while (1) { + int status; + unsigned i; + + status = mmc_spi_readbytes(host, n); + if (status < 0) + return status; + + for (i = 0; i < n; i++) { + if (cp[i] != byte) + return cp[i]; + } + + /* REVISIT investigate msleep() to avoid busy-wait I/O + * in at least some cases. + */ + if (ktime_to_ns(ktime_sub(ktime_get(), timeout)) > 0) + break; + } + return -ETIMEDOUT; +} + +static inline int +mmc_spi_wait_unbusy(struct mmc_spi_host *host, ktime_t timeout) +{ + return mmc_spi_skip(host, timeout, sizeof(host->data->status), 0); +} + +static int mmc_spi_readtoken(struct mmc_spi_host *host) +{ + return mmc_spi_skip(host, readblock_timeout, 1, 0xff); +} + + +/* + * Note that for SPI, cmd->resp[0] is not the same data as "native" protocol + * hosts return! The low byte holds R1_SPI bits. The next byte may hold + * R2_SPI bits ... for SEND_STATUS, or after data read errors. + * + * cmd->resp[1] holds any four-byte response, for R3 (READ_OCR) and on + * newer cards R7 (IF_COND). + */ + +static char *maptype(struct mmc_command *cmd) +{ + switch (mmc_spi_resp_type(cmd)) { + case MMC_RSP_SPI_R1: return "R1"; + case MMC_RSP_SPI_R1B: return "R1B"; + case MMC_RSP_SPI_R2: return "R2/R5"; + case MMC_RSP_SPI_R3: return "R3/R4/R7"; + default: return "?"; + } +} + +/* return zero, else negative errno after setting cmd->error */ +static int mmc_spi_response_get(struct mmc_spi_host *host, + struct mmc_command *cmd, int cs_on) +{ + u8 *cp = host->data->status; + u8 *end = cp + host->t.len; + int value = 0; + char tag[32]; + + snprintf(tag, sizeof(tag), " ... CMD%d response SPI_%s", + cmd->opcode, maptype(cmd)); + + /* Except for data block reads, the whole response will already + * be stored in the scratch buffer. It's somewhere after the + * command and the first byte we read after it. We ignore that + * first byte. After STOP_TRANSMISSION command it may include + * two data bits, but otherwise it's all ones. + */ + cp += 8; + while (cp < end && *cp == 0xff) + cp++; + + /* Data block reads (R1 response types) may need more data... */ + if (cp == end) { + unsigned i; + + cp = host->data->status; + + /* Card sends N(CR) (== 1..8) bytes of all-ones then one + * status byte ... and we already scanned 2 bytes. + * + * REVISIT block read paths use nasty byte-at-a-time I/O + * so it can always DMA directly into the target buffer. + * It'd probably be better to memcpy() the first chunk and + * avoid extra i/o calls... + */ + for (i = 2; i < 9; i++) { + value = mmc_spi_readbytes(host, 1); + if (value < 0) + goto done; + if (*cp != 0xff) + goto checkstatus; + } + value = -ETIMEDOUT; + goto done; + } + +checkstatus: + if (*cp & 0x80) { + dev_dbg(&host->spi->dev, "%s: INVALID RESPONSE, %02x\n", + tag, *cp); + value = -EBADR; + goto done; + } + + cmd->resp[0] = *cp++; + cmd->error = 0; + + /* Status byte: the entire seven-bit R1 response. */ + if (cmd->resp[0] != 0) { + if ((R1_SPI_PARAMETER | R1_SPI_ADDRESS + | R1_SPI_ILLEGAL_COMMAND) + & cmd->resp[0]) + value = -EINVAL; + else if (R1_SPI_COM_CRC & cmd->resp[0]) + value = -EILSEQ; + else if ((R1_SPI_ERASE_SEQ | R1_SPI_ERASE_RESET) + & cmd->resp[0]) + value = -EIO; + /* else R1_SPI_IDLE, "it's resetting" */ + } + + switch (mmc_spi_resp_type(cmd)) { + + /* SPI R1B == R1 + busy; STOP_TRANSMISSION (for multiblock reads) + * and less-common stuff like various erase operations. + */ + case MMC_RSP_SPI_R1B: + /* maybe we read all the busy tokens already */ + while (cp < end && *cp == 0) + cp++; + if (cp == end) + mmc_spi_wait_unbusy(host, r1b_timeout); + break; + + /* SPI R2 == R1 + second status byte; SEND_STATUS + * SPI R5 == R1 + data byte; IO_RW_DIRECT + */ + case MMC_RSP_SPI_R2: + cmd->resp[0] |= *cp << 8; + break; + + /* SPI R3, R4, or R7 == R1 + 4 bytes */ + case MMC_RSP_SPI_R3: + cmd->resp[1] = be32_to_cpu(get_unaligned((u32 *)cp)); + break; + + /* SPI R1 == just one status byte */ + case MMC_RSP_SPI_R1: + break; + + default: + dev_dbg(&host->spi->dev, "bad response type %04x\n", + mmc_spi_resp_type(cmd)); + if (value >= 0) + value = -EINVAL; + goto done; + } + + if (value < 0) + dev_dbg(&host->spi->dev, "%s: resp %04x %08x\n", + tag, cmd->resp[0], cmd->resp[1]); + + /* disable chipselect on errors and some success cases */ + if (value >= 0 && cs_on) + return value; +done: + if (value < 0) + cmd->error = value; + mmc_cs_off(host); + return value; +} + +/* Issue command and read its response. + * Returns zero on success, negative for error. + * + * On error, caller must cope with mmc core retry mechanism. That + * means immediate low-level resubmit, which affects the bus lock... + */ +static int +mmc_spi_command_send(struct mmc_spi_host *host, + struct mmc_request *mrq, + struct mmc_command *cmd, int cs_on) +{ + struct scratch *data = host->data; + u8 *cp = data->status; + u32 arg = cmd->arg; + int status; + struct spi_transfer *t; + + /* We can handle most commands (except block reads) in one full + * duplex I/O operation before either starting the next transfer + * (data block or command) or else deselecting the card. + * + * First, write 7 bytes: + * - an all-ones byte to ensure the card is ready + * - opcode byte (plus start and transmission bits) + * - four bytes of big-endian argument + * - crc7 (plus end bit) ... always computed, it's cheap + * + * We init the whole buffer to all-ones, which is what we need + * to write while we're reading (later) response data. + */ + memset(cp++, 0xff, sizeof(data->status)); + + *cp++ = 0x40 | cmd->opcode; + *cp++ = (u8)(arg >> 24); + *cp++ = (u8)(arg >> 16); + *cp++ = (u8)(arg >> 8); + *cp++ = (u8)arg; + *cp++ = (crc7(0, &data->status[1], 5) << 1) | 0x01; + + /* Then, read up to 13 bytes (while writing all-ones): + * - N(CR) (== 1..8) bytes of all-ones + * - status byte (for all response types) + * - the rest of the response, either: + * + nothing, for R1 or R1B responses + * + second status byte, for R2 responses + * + four data bytes, for R3 and R7 responses + * + * Finally, read some more bytes ... in the nice cases we know in + * advance how many, and reading 1 more is always OK: + * - N(EC) (== 0..N) bytes of all-ones, before deselect/finish + * - N(RC) (== 1..N) bytes of all-ones, before next command + * - N(WR) (== 1..N) bytes of all-ones, before data write + * + * So in those cases one full duplex I/O of at most 21 bytes will + * handle the whole command, leaving the card ready to receive a + * data block or new command. We do that whenever we can, shaving + * CPU and IRQ costs (especially when using DMA or FIFOs). + * + * There are two other cases, where it's not generally practical + * to rely on a single I/O: + * + * - R1B responses need at least N(EC) bytes of all-zeroes. + * + * In this case we can *try* to fit it into one I/O, then + * maybe read more data later. + * + * - Data block reads are more troublesome, since a variable + * number of padding bytes precede the token and data. + * + N(CX) (== 0..8) bytes of all-ones, before CSD or CID + * + N(AC) (== 1..many) bytes of all-ones + * + * In this case we currently only have minimal speedups here: + * when N(CR) == 1 we can avoid I/O in response_get(). + */ + if (cs_on && (mrq->data->flags & MMC_DATA_READ)) { + cp += 2; /* min(N(CR)) + status */ + /* R1 */ + } else { + cp += 10; /* max(N(CR)) + status + min(N(RC),N(WR)) */ + if (cmd->flags & MMC_RSP_SPI_S2) /* R2/R5 */ + cp++; + else if (cmd->flags & MMC_RSP_SPI_B4) /* R3/R4/R7 */ + cp += 4; + else if (cmd->flags & MMC_RSP_BUSY) /* R1B */ + cp = data->status + sizeof(data->status); + /* else: R1 (most commands) */ + } + + dev_dbg(&host->spi->dev, " mmc_spi: CMD%d, resp %s\n", + cmd->opcode, maptype(cmd)); + + /* send command, leaving chipselect active */ + spi_message_init(&host->m); + + t = &host->t; + memset(t, 0, sizeof(*t)); + t->tx_buf = t->rx_buf = data->status; + t->tx_dma = t->rx_dma = host->data_dma; + t->len = cp - data->status; + t->cs_change = 1; + spi_message_add_tail(t, &host->m); + + if (host->dma_dev) { + host->m.is_dma_mapped = 1; + dma_sync_single_for_device(host->dma_dev, + host->data_dma, sizeof(*host->data), + DMA_BIDIRECTIONAL); + } + status = spi_sync(host->spi, &host->m); + if (status == 0) + status = host->m.status; + + if (host->dma_dev) + dma_sync_single_for_cpu(host->dma_dev, + host->data_dma, sizeof(*host->data), + DMA_BIDIRECTIONAL); + if (status < 0) { + dev_dbg(&host->spi->dev, " ... write returned %d\n", status); + cmd->error = status; + return status; + } + + /* after no-data commands and STOP_TRANSMISSION, chipselect off */ + return mmc_spi_response_get(host, cmd, cs_on); +} + +/* Build data message with up to four separate transfers. For TX, we + * start by writing the data token. And in most cases, we finish with + * a status transfer. + * + * We always provide TX data for data and CRC. The MMC/SD protocol + * requires us to write ones; but Linux defaults to writing zeroes; + * so we explicitly initialize it to all ones on RX paths. + * + * We also handle DMA mapping, so the underlying SPI controller does + * not need to (re)do it for each message. + */ +static void +mmc_spi_setup_data_message( + struct mmc_spi_host *host, + int multiple, + enum dma_data_direction direction) +{ + struct spi_transfer *t; + struct scratch *scratch = host->data; + dma_addr_t dma = host->data_dma; + + spi_message_init(&host->m); + if (dma) + host->m.is_dma_mapped = 1; + + /* for reads, readblock() skips 0xff bytes before finding + * the token; for writes, this transfer issues that token. + */ + if (direction == DMA_TO_DEVICE) { + t = &host->token; + memset(t, 0, sizeof(*t)); + t->len = 1; + if (multiple) + scratch->data_token = SPI_TOKEN_MULTI_WRITE; + else + scratch->data_token = SPI_TOKEN_SINGLE; + t->tx_buf = &scratch->data_token; + if (dma) + t->tx_dma = dma + offsetof(struct scratch, data_token); + spi_message_add_tail(t, &host->m); + } + + /* Body of transfer is buffer, then CRC ... + * either TX-only, or RX with TX-ones. + */ + t = &host->t; + memset(t, 0, sizeof(*t)); + t->tx_buf = host->ones; + t->tx_dma = host->ones_dma; + /* length and actual buffer info are written later */ + spi_message_add_tail(t, &host->m); + + t = &host->crc; + memset(t, 0, sizeof(*t)); + t->len = 2; + if (direction == DMA_TO_DEVICE) { + /* the actual CRC may get written later */ + t->tx_buf = &scratch->crc_val; + if (dma) + t->tx_dma = dma + offsetof(struct scratch, crc_val); + } else { + t->tx_buf = host->ones; + t->tx_dma = host->ones_dma; + t->rx_buf = &scratch->crc_val; + if (dma) + t->rx_dma = dma + offsetof(struct scratch, crc_val); + } + spi_message_add_tail(t, &host->m); + + /* + * A single block read is followed by N(EC) [0+] all-ones bytes + * before deselect ... don't bother. + * + * Multiblock reads are followed by N(AC) [1+] all-ones bytes before + * the next block is read, or a STOP_TRANSMISSION is issued. We'll + * collect that single byte, so readblock() doesn't need to. + * + * For a write, the one-byte data response follows immediately, then + * come zero or more busy bytes, then N(WR) [1+] all-ones bytes. + * Then single block reads may deselect, and multiblock ones issue + * the next token (next data block, or STOP_TRAN). We can try to + * minimize I/O ops by using a single read to collect end-of-busy. + */ + if (multiple || direction == DMA_TO_DEVICE) { + t = &host->early_status; + memset(t, 0, sizeof(*t)); + t->len = (direction == DMA_TO_DEVICE) + ? sizeof(scratch->status) + : 1; + t->tx_buf = host->ones; + t->tx_dma = host->ones_dma; + t->rx_buf = scratch->status; + if (dma) + t->rx_dma = dma + offsetof(struct scratch, status); + t->cs_change = 1; + spi_message_add_tail(t, &host->m); + } +} + +/* + * Write one block: + * - caller handled preceding N(WR) [1+] all-ones bytes + * - data block + * + token + * + data bytes + * + crc16 + * - an all-ones byte ... card writes a data-response byte + * - followed by N(EC) [0+] all-ones bytes, card writes zero/'busy' + * + * Return negative errno, else success. + */ +static int +mmc_spi_writeblock(struct mmc_spi_host *host, struct spi_transfer *t) +{ + struct spi_device *spi = host->spi; + int status, i; + struct scratch *scratch = host->data; + + if (host->mmc->use_spi_crc) + scratch->crc_val = cpu_to_be16( + crc_itu_t(0, t->tx_buf, t->len)); + if (host->dma_dev) + dma_sync_single_for_device(host->dma_dev, + host->data_dma, sizeof(*scratch), + DMA_BIDIRECTIONAL); + + status = spi_sync(spi, &host->m); + if (status == 0) + status = host->m.status; + + if (status != 0) { + dev_dbg(&spi->dev, "write error (%d)\n", status); + return status; + } + + if (host->dma_dev) + dma_sync_single_for_cpu(host->dma_dev, + host->data_dma, sizeof(*scratch), + DMA_BIDIRECTIONAL); + + /* + * Get the transmission data-response reply. It must follow + * immediately after the data block we transferred. This reply + * doesn't necessarily tell whether the write operation succeeded; + * it just says if the transmission was ok and whether *earlier* + * writes succeeded; see the standard. + */ + switch (SPI_MMC_RESPONSE_CODE(scratch->status[0])) { + case SPI_RESPONSE_ACCEPTED: + status = 0; + break; + case SPI_RESPONSE_CRC_ERR: + /* host shall then issue MMC_STOP_TRANSMISSION */ + status = -EILSEQ; + break; + case SPI_RESPONSE_WRITE_ERR: + /* host shall then issue MMC_STOP_TRANSMISSION, + * and should MMC_SEND_STATUS to sort it out + */ + status = -EIO; + break; + default: + status = -EPROTO; + break; + } + if (status != 0) { + dev_dbg(&spi->dev, "write error %02x (%d)\n", + scratch->status[0], status); + return status; + } + + t->tx_buf += t->len; + if (host->dma_dev) + t->tx_dma += t->len; + + /* Return when not busy. If we didn't collect that status yet, + * we'll need some more I/O. + */ + for (i = 1; i < sizeof(scratch->status); i++) { + if (scratch->status[i] != 0) + return 0; + } + return mmc_spi_wait_unbusy(host, writeblock_timeout); +} + +/* + * Read one block: + * - skip leading all-ones bytes ... either + * + N(AC) [1..f(clock,CSD)] usually, else + * + N(CX) [0..8] when reading CSD or CID + * - data block + * + token ... if error token, no data or crc + * + data bytes + * + crc16 + * + * After single block reads, we're done; N(EC) [0+] all-ones bytes follow + * before dropping chipselect. + * + * For multiblock reads, caller either reads the next block or issues a + * STOP_TRANSMISSION command. + */ +static int +mmc_spi_readblock(struct mmc_spi_host *host, struct spi_transfer *t) +{ + struct spi_device *spi = host->spi; + int status; + struct scratch *scratch = host->data; + + /* At least one SD card sends an all-zeroes byte when N(CX) + * applies, before the all-ones bytes ... just cope with that. + */ + status = mmc_spi_readbytes(host, 1); + if (status < 0) + return status; + status = scratch->status[0]; + if (status == 0xff || status == 0) + status = mmc_spi_readtoken(host); + + if (status == SPI_TOKEN_SINGLE) { + if (host->dma_dev) { + dma_sync_single_for_device(host->dma_dev, + host->data_dma, sizeof(*scratch), + DMA_BIDIRECTIONAL); + dma_sync_single_for_device(host->dma_dev, + t->rx_dma, t->len, + DMA_FROM_DEVICE); + } + + status = spi_sync(spi, &host->m); + if (status == 0) + status = host->m.status; + + if (host->dma_dev) { + dma_sync_single_for_cpu(host->dma_dev, + host->data_dma, sizeof(*scratch), + DMA_BIDIRECTIONAL); + dma_sync_single_for_cpu(host->dma_dev, + t->rx_dma, t->len, + DMA_FROM_DEVICE); + } + + } else { + dev_dbg(&spi->dev, "read error %02x (%d)\n", status, status); + + /* we've read extra garbage, timed out, etc */ + if (status < 0) + return status; + + /* low four bits are an R2 subset, fifth seems to be + * vendor specific ... map them all to generic error.. + */ + return -EIO; + } + + if (host->mmc->use_spi_crc) { + u16 crc = crc_itu_t(0, t->rx_buf, t->len); + + be16_to_cpus(&scratch->crc_val); + if (scratch->crc_val != crc) { + dev_dbg(&spi->dev, "read - crc error: crc_val=0x%04x, " + "computed=0x%04x len=%d\n", + scratch->crc_val, crc, t->len); + return -EILSEQ; + } + } + + t->rx_buf += t->len; + if (host->dma_dev) + t->rx_dma += t->len; + + return 0; +} + +/* + * An MMC/SD data stage includes one or more blocks, optional CRCs, + * and inline handshaking. That handhaking makes it unlike most + * other SPI protocol stacks. + */ +static void +mmc_spi_data_do(struct mmc_spi_host *host, struct mmc_command *cmd, + struct mmc_data *data, u32 blk_size) +{ + struct spi_device *spi = host->spi; + struct device *dma_dev = host->dma_dev; + struct spi_transfer *t; + enum dma_data_direction direction; + struct scatterlist *sg; + unsigned n_sg; + int multiple = (data->blocks > 1); + + if (data->flags & MMC_DATA_READ) + direction = DMA_FROM_DEVICE; + else + direction = DMA_TO_DEVICE; + mmc_spi_setup_data_message(host, multiple, direction); + t = &host->t; + + /* Handle scatterlist segments one at a time, with synch for + * each 512-byte block + */ + for (sg = data->sg, n_sg = data->sg_len; n_sg; n_sg--, sg++) { + int status = 0; + dma_addr_t dma_addr = 0; + void *kmap_addr; + unsigned length = sg->length; + enum dma_data_direction dir = direction; + + /* set up dma mapping for controller drivers that might + * use DMA ... though they may fall back to PIO + */ + if (dma_dev) { + /* never invalidate whole *shared* pages ... */ + if ((sg->offset != 0 || length != PAGE_SIZE) + && dir == DMA_FROM_DEVICE) + dir = DMA_BIDIRECTIONAL; + + dma_addr = dma_map_page(dma_dev, sg->page, 0, + PAGE_SIZE, dir); + if (direction == DMA_TO_DEVICE) + t->tx_dma = dma_addr + sg->offset; + else + t->rx_dma = dma_addr + sg->offset; + } + + /* allow pio too; we don't allow highmem */ + kmap_addr = kmap(sg->page); + if (direction == DMA_TO_DEVICE) + t->tx_buf = kmap_addr + sg->offset; + else + t->rx_buf = kmap_addr + sg->offset; + + /* transfer each block, and update request status */ + while (length) { + t->len = min(length, blk_size); + + dev_dbg(&host->spi->dev, + " mmc_spi: %s block, %d bytes\n", + (direction == DMA_TO_DEVICE) + ? "write" + : "read", + t->len); + + if (direction == DMA_TO_DEVICE) + status = mmc_spi_writeblock(host, t); + else + status = mmc_spi_readblock(host, t); + if (status < 0) + break; + + data->bytes_xfered += t->len; + length -= t->len; + + if (!multiple) + break; + } + + /* discard mappings */ + if (direction == DMA_FROM_DEVICE) + flush_kernel_dcache_page(sg->page); + kunmap(sg->page); + if (dma_dev) + dma_unmap_page(dma_dev, dma_addr, PAGE_SIZE, dir); + + if (status < 0) { + data->error = status; + dev_dbg(&spi->dev, "%s status %d\n", + (direction == DMA_TO_DEVICE) + ? "write" : "read", + status); + break; + } + } + + /* NOTE some docs describe an MMC-only SET_BLOCK_COUNT (CMD23) that + * can be issued before multiblock writes. Unlike its more widely + * documented analogue for SD cards (SET_WR_BLK_ERASE_COUNT, ACMD23), + * that can affect the STOP_TRAN logic. Complete (and current) + * MMC specs should sort that out before Linux starts using CMD23. + */ + if (direction == DMA_TO_DEVICE && multiple) { + struct scratch *scratch = host->data; + int tmp; + const unsigned statlen = sizeof(scratch->status); + + dev_dbg(&spi->dev, " mmc_spi: STOP_TRAN\n"); + + /* Tweak the per-block message we set up earlier by morphing + * it to hold single buffer with the token followed by some + * all-ones bytes ... skip N(BR) (0..1), scan the rest for + * "not busy any longer" status, and leave chip selected. + */ + INIT_LIST_HEAD(&host->m.transfers); + list_add(&host->early_status.transfer_list, + &host->m.transfers); + + memset(scratch->status, 0xff, statlen); + scratch->status[0] = SPI_TOKEN_STOP_TRAN; + + host->early_status.tx_buf = host->early_status.rx_buf; + host->early_status.tx_dma = host->early_status.rx_dma; + host->early_status.len = statlen; + + if (host->dma_dev) + dma_sync_single_for_device(host->dma_dev, + host->data_dma, sizeof(*scratch), + DMA_BIDIRECTIONAL); + + tmp = spi_sync(spi, &host->m); + if (tmp == 0) + tmp = host->m.status; + + if (host->dma_dev) + dma_sync_single_for_cpu(host->dma_dev, + host->data_dma, sizeof(*scratch), + DMA_BIDIRECTIONAL); + + if (tmp < 0) { + if (!data->error) + data->error = tmp; + return; + } + + /* Ideally we collected "not busy" status with one I/O, + * avoiding wasteful byte-at-a-time scanning... but more + * I/O is often needed. + */ + for (tmp = 2; tmp < statlen; tmp++) { + if (scratch->status[tmp] != 0) + return; + } + tmp = mmc_spi_wait_unbusy(host, writeblock_timeout); + if (tmp < 0 && !data->error) + data->error = tmp; + } +} + +/****************************************************************************/ + +/* + * MMC driver implementation -- the interface to the MMC stack + */ + +static void mmc_spi_request(struct mmc_host *mmc, struct mmc_request *mrq) +{ + struct mmc_spi_host *host = mmc_priv(mmc); + int status = -EINVAL; + +#ifdef DEBUG + /* MMC core and layered drivers *MUST* issue SPI-aware commands */ + { + struct mmc_command *cmd; + int invalid = 0; + + cmd = mrq->cmd; + if (!mmc_spi_resp_type(cmd)) { + dev_dbg(&host->spi->dev, "bogus command\n"); + cmd->error = -EINVAL; + invalid = 1; + } + + cmd = mrq->stop; + if (cmd && !mmc_spi_resp_type(cmd)) { + dev_dbg(&host->spi->dev, "bogus STOP command\n"); + cmd->error = -EINVAL; + invalid = 1; + } + + if (invalid) { + dump_stack(); + mmc_request_done(host->mmc, mrq); + return; + } + } +#endif + + /* issue command; then optionally data and stop */ + status = mmc_spi_command_send(host, mrq, mrq->cmd, mrq->data != NULL); + if (status == 0 && mrq->data) { + mmc_spi_data_do(host, mrq->cmd, mrq->data, mrq->data->blksz); + if (mrq->stop) + status = mmc_spi_command_send(host, mrq, mrq->stop, 0); + else + mmc_cs_off(host); + } + + mmc_request_done(host->mmc, mrq); +} + +/* See Section 6.4.1, in SD "Simplified Physical Layer Specification 2.0" + * + * NOTE that here we can't know that the card has just been powered up; + * not all MMC/SD sockets support power switching. + * + * FIXME when the card is still in SPI mode, e.g. from a previous kernel, + * this doesn't seem to do the right thing at all... + */ +static void mmc_spi_initsequence(struct mmc_spi_host *host) +{ + /* Try to be very sure any previous command has completed; + * wait till not-busy, skip debris from any old commands. + */ + mmc_spi_wait_unbusy(host, r1b_timeout); + mmc_spi_readbytes(host, 10); + + /* + * Do a burst with chipselect active-high. We need to do this to + * meet the requirement of 74 clock cycles with both chipselect + * and CMD (MOSI) high before CMD0 ... after the card has been + * powered up to Vdd(min), and so is ready to take commands. + * + * Some cards are particularly needy of this (e.g. Viking "SD256") + * while most others don't seem to care. + * + * Note that this is one of the places MMC/SD plays games with the + * SPI protocol. Another is that when chipselect is released while + * the card returns BUSY status, the clock must issue several cycles + * with chipselect high before the card will stop driving its output. + */ + host->spi->mode |= SPI_CS_HIGH; + if (spi_setup(host->spi) != 0) { + /* Just warn; most cards work without it. */ + dev_warn(&host->spi->dev, + "can't change chip-select polarity\n"); + host->spi->mode &= ~SPI_CS_HIGH; + } else { + mmc_spi_readbytes(host, 18); + + host->spi->mode &= ~SPI_CS_HIGH; + if (spi_setup(host->spi) != 0) { + /* Wot, we can't get the same setup we had before? */ + dev_err(&host->spi->dev, + "can't restore chip-select polarity\n"); + } + } +} + +static char *mmc_powerstring(u8 power_mode) +{ + switch (power_mode) { + case MMC_POWER_OFF: return "off"; + case MMC_POWER_UP: return "up"; + case MMC_POWER_ON: return "on"; + } + return "?"; +} + +static void mmc_spi_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) +{ + struct mmc_spi_host *host = mmc_priv(mmc); + + if (host->power_mode != ios->power_mode) { + int canpower; + + canpower = host->pdata && host->pdata->setpower; + + dev_dbg(&host->spi->dev, "mmc_spi: power %s (%d)%s\n", + mmc_powerstring(ios->power_mode), + ios->vdd, + canpower ? ", can switch" : ""); + + /* switch power on/off if possible, accounting for + * max 250msec powerup time if needed. + */ + if (canpower) { + switch (ios->power_mode) { + case MMC_POWER_OFF: + case MMC_POWER_UP: + host->pdata->setpower(&host->spi->dev, + ios->vdd); + if (ios->power_mode == MMC_POWER_UP) + msleep(host->powerup_msecs); + } + } + + /* See 6.4.1 in the simplified SD card physical spec 2.0 */ + if (ios->power_mode == MMC_POWER_ON) + mmc_spi_initsequence(host); + + /* If powering down, ground all card inputs to avoid power + * delivery from data lines! On a shared SPI bus, this + * will probably be temporary; 6.4.2 of the simplified SD + * spec says this must last at least 1msec. + * + * - Clock low means CPOL 0, e.g. mode 0 + * - MOSI low comes from writing zero + * - Chipselect is usually active low... + */ + if (canpower && ios->power_mode == MMC_POWER_OFF) { + int mres; + + host->spi->mode &= ~(SPI_CPOL|SPI_CPHA); + mres = spi_setup(host->spi); + if (mres < 0) + dev_dbg(&host->spi->dev, + "switch to SPI mode 0 failed\n"); + + if (spi_w8r8(host->spi, 0x00) < 0) + dev_dbg(&host->spi->dev, + "put spi signals to low failed\n"); + + /* + * Now clock should be low due to spi mode 0; + * MOSI should be low because of written 0x00; + * chipselect should be low (it is active low) + * power supply is off, so now MMC is off too! + * + * FIXME no, chipselect can be high since the + * device is inactive and SPI_CS_HIGH is clear... + */ + msleep(10); + if (mres == 0) { + host->spi->mode |= (SPI_CPOL|SPI_CPHA); + mres = spi_setup(host->spi); + if (mres < 0) + dev_dbg(&host->spi->dev, + "switch back to SPI mode 3" + " failed\n"); + } + } + + host->power_mode = ios->power_mode; + } + + if (host->spi->max_speed_hz != ios->clock && ios->clock != 0) { + int status; + + host->spi->max_speed_hz = ios->clock; + status = spi_setup(host->spi); + dev_dbg(&host->spi->dev, + "mmc_spi: clock to %d Hz, %d\n", + host->spi->max_speed_hz, status); + } +} + +static int mmc_spi_get_ro(struct mmc_host *mmc) +{ + struct mmc_spi_host *host = mmc_priv(mmc); + + if (host->pdata && host->pdata->get_ro) + return host->pdata->get_ro(mmc->parent); + /* board doesn't support read only detection; assume writeable */ + return 0; +} + + +static const struct mmc_host_ops mmc_spi_ops = { + .request = mmc_spi_request, + .set_ios = mmc_spi_set_ios, + .get_ro = mmc_spi_get_ro, +}; + + +/****************************************************************************/ + +/* + * SPI driver implementation + */ + +static irqreturn_t +mmc_spi_detect_irq(int irq, void *mmc) +{ + struct mmc_spi_host *host = mmc_priv(mmc); + u16 delay_msec = max(host->pdata->detect_delay, (u16)100); + + mmc_detect_change(mmc, msecs_to_jiffies(delay_msec)); + return IRQ_HANDLED; +} + +static int mmc_spi_probe(struct spi_device *spi) +{ + void *ones; + struct mmc_host *mmc; + struct mmc_spi_host *host; + int status; + + /* MMC and SD specs only seem to care that sampling is on the + * rising edge ... meaning SPI modes 0 or 3. So either SPI mode + * should be legit. We'll use mode 0 since it seems to be a + * bit less troublesome on some hardware ... unclear why. + */ + spi->mode = SPI_MODE_0; + spi->bits_per_word = 8; + + status = spi_setup(spi); + if (status < 0) { + dev_dbg(&spi->dev, "needs SPI mode %02x, %d KHz; %d\n", + spi->mode, spi->max_speed_hz / 1000, + status); + return status; + } + + /* We can use the bus safely iff nobody else will interfere with + * us. That is, either we have the experimental exclusive access + * primitives ... or else there's nobody to share it with. + */ + if (spi->master->num_chipselect > 1) { + struct device *parent = spi->dev.parent; + + /* If there are multiple devices on this bus, we + * can't proceed. + */ + spin_lock(&parent->klist_children.k_lock); + if (parent->klist_children.k_list.next + != parent->klist_children.k_list.prev) + status = -EMLINK; + else + status = 0; + spin_unlock(&parent->klist_children.k_lock); + if (status < 0) { + dev_err(&spi->dev, "can't share SPI bus\n"); + return status; + } + + /* REVISIT we can't guarantee another device won't + * be added later. It's uncommon though ... for now, + * work as if this is safe. + */ + dev_warn(&spi->dev, "ASSUMING unshared SPI bus!\n"); + } + + /* We need a supply of ones to transmit. This is the only time + * the CPU touches these, so cache coherency isn't a concern. + * + * NOTE if many systems use more than one MMC-over-SPI connector + * it'd save some memory to share this. That's evidently rare. + */ + status = -ENOMEM; + ones = kmalloc(MMC_SPI_BLOCKSIZE, GFP_KERNEL); + if (!ones) + goto nomem; + memset(ones, 0xff, MMC_SPI_BLOCKSIZE); + + mmc = mmc_alloc_host(sizeof(*host), &spi->dev); + if (!mmc) + goto nomem; + + mmc->ops = &mmc_spi_ops; + mmc->max_blk_size = MMC_SPI_BLOCKSIZE; + + /* As long as we keep track of the number of successfully + * transmitted blocks, we're good for multiwrite. + */ + mmc->caps = MMC_CAP_SPI | MMC_CAP_MULTIWRITE; + + /* SPI doesn't need the lowspeed device identification thing for + * MMC or SD cards, since it never comes up in open drain mode. + * That's good; some SPI masters can't handle very low speeds! + * + * However, low speed SDIO cards need not handle over 400 KHz; + * that's the only reason not to use a few MHz for f_min (until + * the upper layer reads the target frequency from the CSD). + */ + mmc->f_min = 400000; + mmc->f_max = spi->max_speed_hz; + + host = mmc_priv(mmc); + host->mmc = mmc; + host->spi = spi; + + host->ones = ones; + + /* Platform data is used to hook up things like card sensing + * and power switching gpios. + */ + host->pdata = spi->dev.platform_data; + if (host->pdata) + mmc->ocr_avail = host->pdata->ocr_mask; + if (!mmc->ocr_avail) { + dev_warn(&spi->dev, "ASSUMING 3.2-3.4 V slot power\n"); + mmc->ocr_avail = MMC_VDD_32_33|MMC_VDD_33_34; + } + if (host->pdata && host->pdata->setpower) { + host->powerup_msecs = host->pdata->powerup_msecs; + if (!host->powerup_msecs || host->powerup_msecs > 250) + host->powerup_msecs = 250; + } + + dev_set_drvdata(&spi->dev, mmc); + + /* preallocate dma buffers */ + host->data = kmalloc(sizeof(*host->data), GFP_KERNEL); + if (!host->data) + goto fail_nobuf1; + + if (spi->master->cdev.dev->dma_mask) { + struct device *dev = spi->master->cdev.dev; + + host->dma_dev = dev; + host->ones_dma = dma_map_single(dev, ones, + MMC_SPI_BLOCKSIZE, DMA_TO_DEVICE); + host->data_dma = dma_map_single(dev, host->data, + sizeof(*host->data), DMA_BIDIRECTIONAL); + + /* REVISIT in theory those map operations can fail... */ + + dma_sync_single_for_cpu(host->dma_dev, + host->data_dma, sizeof(*host->data), + DMA_BIDIRECTIONAL); + } + + /* setup message for status/busy readback */ + spi_message_init(&host->readback); + host->readback.is_dma_mapped = (host->dma_dev != NULL); + + spi_message_add_tail(&host->status, &host->readback); + host->status.tx_buf = host->ones; + host->status.tx_dma = host->ones_dma; + host->status.rx_buf = &host->data->status; + host->status.rx_dma = host->data_dma + offsetof(struct scratch, status); + host->status.cs_change = 1; + + /* register card detect irq */ + if (host->pdata && host->pdata->init) { + status = host->pdata->init(&spi->dev, mmc_spi_detect_irq, mmc); + if (status != 0) + goto fail_glue_init; + } + + status = mmc_add_host(mmc); + if (status != 0) + goto fail_add_host; + + dev_info(&spi->dev, "SD/MMC host %s%s%s%s\n", + mmc->class_dev.bus_id, + host->dma_dev ? "" : ", no DMA", + (host->pdata && host->pdata->get_ro) + ? "" : ", no WP", + (host->pdata && host->pdata->setpower) + ? "" : ", no poweroff"); + return 0; + +fail_add_host: + mmc_remove_host (mmc); +fail_glue_init: + if (host->dma_dev) + dma_unmap_single(host->dma_dev, host->data_dma, + sizeof(*host->data), DMA_BIDIRECTIONAL); + kfree(host->data); + +fail_nobuf1: + mmc_free_host(mmc); + dev_set_drvdata(&spi->dev, NULL); + +nomem: + kfree(ones); + return status; +} + + +static int __devexit mmc_spi_remove(struct spi_device *spi) +{ + struct mmc_host *mmc = dev_get_drvdata(&spi->dev); + struct mmc_spi_host *host; + + if (mmc) { + host = mmc_priv(mmc); + + /* prevent new mmc_detect_change() calls */ + if (host->pdata && host->pdata->exit) + host->pdata->exit(&spi->dev, mmc); + + mmc_remove_host(mmc); + + if (host->dma_dev) { + dma_unmap_single(host->dma_dev, host->ones_dma, + MMC_SPI_BLOCKSIZE, DMA_TO_DEVICE); + dma_unmap_single(host->dma_dev, host->data_dma, + sizeof(*host->data), DMA_BIDIRECTIONAL); + } + + kfree(host->data); + kfree(host->ones); + + spi->max_speed_hz = mmc->f_max; + mmc_free_host(mmc); + dev_set_drvdata(&spi->dev, NULL); + } + return 0; +} + + +static struct spi_driver mmc_spi_driver = { + .driver = { + .name = "mmc_spi", + .bus = &spi_bus_type, + .owner = THIS_MODULE, + }, + .probe = mmc_spi_probe, + .remove = __devexit_p(mmc_spi_remove), +}; + + +static int __init mmc_spi_init(void) +{ + return spi_register_driver(&mmc_spi_driver); +} +module_init(mmc_spi_init); + + +static void __exit mmc_spi_exit(void) +{ + spi_unregister_driver(&mmc_spi_driver); +} +module_exit(mmc_spi_exit); + + +MODULE_AUTHOR("Mike Lavender, David Brownell, " + "Hans-Peter Nilsson, Jan Nikitenko"); +MODULE_DESCRIPTION("SPI SD/MMC host driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c index be730c0a0352..d0eb0a2abf4d 100644 --- a/drivers/mmc/host/mmci.c +++ b/drivers/mmc/host/mmci.c @@ -16,6 +16,7 @@ #include <linux/delay.h> #include <linux/err.h> #include <linux/highmem.h> +#include <linux/log2.h> #include <linux/mmc/host.h> #include <linux/amba/bus.h> #include <linux/clk.h> @@ -154,11 +155,11 @@ mmci_data_irq(struct mmci_host *host, struct mmc_data *data, } if (status & (MCI_DATACRCFAIL|MCI_DATATIMEOUT|MCI_TXUNDERRUN|MCI_RXOVERRUN)) { if (status & MCI_DATACRCFAIL) - data->error = MMC_ERR_BADCRC; + data->error = -EILSEQ; else if (status & MCI_DATATIMEOUT) - data->error = MMC_ERR_TIMEOUT; + data->error = -ETIMEDOUT; else if (status & (MCI_TXUNDERRUN|MCI_RXOVERRUN)) - data->error = MMC_ERR_FIFO; + data->error = -EIO; status |= MCI_DATAEND; /* @@ -193,12 +194,12 @@ mmci_cmd_irq(struct mmci_host *host, struct mmc_command *cmd, cmd->resp[3] = readl(base + MMCIRESPONSE3); if (status & MCI_CMDTIMEOUT) { - cmd->error = MMC_ERR_TIMEOUT; + cmd->error = -ETIMEDOUT; } else if (status & MCI_CMDCRCFAIL && cmd->flags & MMC_RSP_CRC) { - cmd->error = MMC_ERR_BADCRC; + cmd->error = -EILSEQ; } - if (!cmd->data || cmd->error != MMC_ERR_NONE) { + if (!cmd->data || cmd->error) { if (host->data) mmci_stop_data(host); mmci_request_end(host, cmd->mrq); @@ -391,6 +392,14 @@ static void mmci_request(struct mmc_host *mmc, struct mmc_request *mrq) WARN_ON(host->mrq != NULL); + if (mrq->data && !is_power_of_2(mrq->data->blksz)) { + printk(KERN_ERR "%s: Unsupported block size (%d bytes)\n", + mmc_hostname(mmc), mrq->data->blksz); + mrq->cmd->error = -EINVAL; + mmc_request_done(mmc, mrq); + return; + } + spin_lock_irq(&host->lock); host->mrq = mrq; diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c index 0cf97edc5f58..60a67dfcda6a 100644 --- a/drivers/mmc/host/omap.c +++ b/drivers/mmc/host/omap.c @@ -263,7 +263,7 @@ mmc_omap_xfer_done(struct mmc_omap_host *host, struct mmc_data *data) enum dma_data_direction dma_data_dir; BUG_ON(host->dma_ch < 0); - if (data->error != MMC_ERR_NONE) + if (data->error) omap_stop_dma(host->dma_ch); /* Release DMA channel lazily */ mod_timer(&host->dma_timer, jiffies + HZ); @@ -368,7 +368,7 @@ mmc_omap_cmd_done(struct mmc_omap_host *host, struct mmc_command *cmd) } } - if (host->data == NULL || cmd->error != MMC_ERR_NONE) { + if (host->data == NULL || cmd->error) { host->mrq = NULL; clk_disable(host->fclk); mmc_request_done(host->mmc, cmd->mrq); @@ -475,14 +475,14 @@ static irqreturn_t mmc_omap_irq(int irq, void *dev_id) if (status & OMAP_MMC_STAT_DATA_TOUT) { dev_dbg(mmc_dev(host->mmc), "data timeout\n"); if (host->data) { - host->data->error |= MMC_ERR_TIMEOUT; + host->data->error = -ETIMEDOUT; transfer_error = 1; } } if (status & OMAP_MMC_STAT_DATA_CRC) { if (host->data) { - host->data->error |= MMC_ERR_BADCRC; + host->data->error = -EILSEQ; dev_dbg(mmc_dev(host->mmc), "data CRC error, bytes left %d\n", host->total_bytes_left); @@ -504,7 +504,7 @@ static irqreturn_t mmc_omap_irq(int irq, void *dev_id) dev_err(mmc_dev(host->mmc), "command timeout, CMD %d\n", host->cmd->opcode); - host->cmd->error = MMC_ERR_TIMEOUT; + host->cmd->error = -ETIMEDOUT; end_command = 1; } } @@ -514,7 +514,7 @@ static irqreturn_t mmc_omap_irq(int irq, void *dev_id) dev_err(mmc_dev(host->mmc), "command CRC error (CMD%d, arg 0x%08x)\n", host->cmd->opcode, host->cmd->arg); - host->cmd->error = MMC_ERR_BADCRC; + host->cmd->error = -EILSEQ; end_command = 1; } else dev_err(mmc_dev(host->mmc), diff --git a/drivers/mmc/host/pxamci.c b/drivers/mmc/host/pxamci.c index ff960334b337..657901eecfce 100644 --- a/drivers/mmc/host/pxamci.c +++ b/drivers/mmc/host/pxamci.c @@ -142,6 +142,10 @@ static void pxamci_setup_data(struct pxamci_host *host, struct mmc_data *data) host->dma_dir); for (i = 0; i < host->dma_len; i++) { + unsigned int length = sg_dma_len(&data->sg[i]); + host->sg_cpu[i].dcmd = dcmd | length; + if (length & 31 && !(data->flags & MMC_DATA_READ)) + host->sg_cpu[i].dcmd |= DCMD_ENDIRQEN; if (data->flags & MMC_DATA_READ) { host->sg_cpu[i].dsadr = host->res->start + MMC_RXFIFO; host->sg_cpu[i].dtadr = sg_dma_address(&data->sg[i]); @@ -149,7 +153,6 @@ static void pxamci_setup_data(struct pxamci_host *host, struct mmc_data *data) host->sg_cpu[i].dsadr = sg_dma_address(&data->sg[i]); host->sg_cpu[i].dtadr = host->res->start + MMC_TXFIFO; } - host->sg_cpu[i].dcmd = dcmd | sg_dma_len(&data->sg[i]); host->sg_cpu[i].ddadr = host->sg_dma + (i + 1) * sizeof(struct pxa_dma_desc); } @@ -226,7 +229,7 @@ static int pxamci_cmd_done(struct pxamci_host *host, unsigned int stat) } if (stat & STAT_TIME_OUT_RESPONSE) { - cmd->error = MMC_ERR_TIMEOUT; + cmd->error = -ETIMEDOUT; } else if (stat & STAT_RES_CRC_ERR && cmd->flags & MMC_RSP_CRC) { #ifdef CONFIG_PXA27x /* @@ -239,11 +242,11 @@ static int pxamci_cmd_done(struct pxamci_host *host, unsigned int stat) pr_debug("ignoring CRC from command %d - *risky*\n", cmd->opcode); } else #endif - cmd->error = MMC_ERR_BADCRC; + cmd->error = -EILSEQ; } pxamci_disable_irq(host, END_CMD_RES); - if (host->data && cmd->error == MMC_ERR_NONE) { + if (host->data && !cmd->error) { pxamci_enable_irq(host, DATA_TRAN_DONE); } else { pxamci_finish_request(host, host->mrq); @@ -264,9 +267,9 @@ static int pxamci_data_done(struct pxamci_host *host, unsigned int stat) host->dma_dir); if (stat & STAT_READ_TIME_OUT) - data->error = MMC_ERR_TIMEOUT; + data->error = -ETIMEDOUT; else if (stat & (STAT_CRC_READ_ERROR|STAT_CRC_WRITE_ERROR)) - data->error = MMC_ERR_BADCRC; + data->error = -EILSEQ; /* * There appears to be a hardware design bug here. There seems to @@ -274,7 +277,7 @@ static int pxamci_data_done(struct pxamci_host *host, unsigned int stat) * This means that if there was an error on any block, we mark all * data blocks as being in error. */ - if (data->error == MMC_ERR_NONE) + if (!data->error) data->bytes_xfered = data->blocks * data->blksz; else data->bytes_xfered = 0; @@ -284,7 +287,7 @@ static int pxamci_data_done(struct pxamci_host *host, unsigned int stat) host->data = NULL; if (host->mrq->stop) { pxamci_stop_clock(host); - pxamci_start_cmd(host, host->mrq->stop, 0); + pxamci_start_cmd(host, host->mrq->stop, host->cmdat); } else { pxamci_finish_request(host, host->mrq); } @@ -298,7 +301,7 @@ static irqreturn_t pxamci_irq(int irq, void *devid) unsigned int ireg; int handled = 0; - ireg = readl(host->base + MMC_I_REG); + ireg = readl(host->base + MMC_I_REG) & ~readl(host->base + MMC_I_MASK); if (ireg) { unsigned stat = readl(host->base + MMC_STAT); @@ -309,6 +312,10 @@ static irqreturn_t pxamci_irq(int irq, void *devid) handled |= pxamci_cmd_done(host, stat); if (ireg & DATA_TRAN_DONE) handled |= pxamci_data_done(host, stat); + if (ireg & SDIO_INT) { + mmc_signal_sdio_irq(host->mmc); + handled = 1; + } } return IRQ_RETVAL(handled); @@ -382,20 +389,46 @@ static void pxamci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) host->cmdat |= CMDAT_INIT; } + if (ios->bus_width == MMC_BUS_WIDTH_4) + host->cmdat |= CMDAT_SD_4DAT; + else + host->cmdat &= ~CMDAT_SD_4DAT; + pr_debug("PXAMCI: clkrt = %x cmdat = %x\n", host->clkrt, host->cmdat); } +static void pxamci_enable_sdio_irq(struct mmc_host *host, int enable) +{ + struct pxamci_host *pxa_host = mmc_priv(host); + + if (enable) + pxamci_enable_irq(pxa_host, SDIO_INT); + else + pxamci_disable_irq(pxa_host, SDIO_INT); +} + static const struct mmc_host_ops pxamci_ops = { - .request = pxamci_request, - .get_ro = pxamci_get_ro, - .set_ios = pxamci_set_ios, + .request = pxamci_request, + .get_ro = pxamci_get_ro, + .set_ios = pxamci_set_ios, + .enable_sdio_irq = pxamci_enable_sdio_irq, }; static void pxamci_dma_irq(int dma, void *devid) { - printk(KERN_ERR "DMA%d: IRQ???\n", dma); - DCSR(dma) = DCSR_STARTINTR|DCSR_ENDINTR|DCSR_BUSERR; + struct pxamci_host *host = devid; + int dcsr = DCSR(dma); + DCSR(dma) = dcsr & ~DCSR_STOPIRQEN; + + if (dcsr & DCSR_ENDINTR) { + writel(BUF_PART_FULL, host->base + MMC_PRTBUF); + } else { + printk(KERN_ERR "%s: DMA error on channel %d (DCSR=%#x)\n", + mmc_hostname(host->mmc), dma, dcsr); + host->data->error = -EIO; + pxamci_data_done(host, 0); + } } static irqreturn_t pxamci_detect_irq(int irq, void *devid) @@ -444,9 +477,9 @@ static int pxamci_probe(struct platform_device *pdev) mmc->max_seg_size = PAGE_SIZE; /* - * Block length register is 10 bits. + * Block length register is only 10 bits before PXA27x. */ - mmc->max_blk_size = 1023; + mmc->max_blk_size = (cpu_is_pxa21x() || cpu_is_pxa25x()) ? 1023 : 2048; /* * Block count register is 16 bits. @@ -460,6 +493,12 @@ static int pxamci_probe(struct platform_device *pdev) mmc->ocr_avail = host->pdata ? host->pdata->ocr_mask : MMC_VDD_32_33|MMC_VDD_33_34; + mmc->caps = 0; + host->cmdat = 0; + if (!cpu_is_pxa21x() && !cpu_is_pxa25x()) { + mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ; + host->cmdat |= CMDAT_SDIO_INT_EN; + } host->sg_cpu = dma_alloc_coherent(&pdev->dev, PAGE_SIZE, &host->sg_dma, GFP_KERNEL); if (!host->sg_cpu) { diff --git a/drivers/mmc/host/pxamci.h b/drivers/mmc/host/pxamci.h index df17c281278a..3153e779d46a 100644 --- a/drivers/mmc/host/pxamci.h +++ b/drivers/mmc/host/pxamci.h @@ -25,6 +25,8 @@ #define SPI_EN (1 << 0) #define MMC_CMDAT 0x0010 +#define CMDAT_SDIO_INT_EN (1 << 11) +#define CMDAT_SD_4DAT (1 << 8) #define CMDAT_DMAEN (1 << 7) #define CMDAT_INIT (1 << 6) #define CMDAT_BUSY (1 << 5) diff --git a/drivers/mmc/host/ricoh_mmc.c b/drivers/mmc/host/ricoh_mmc.c new file mode 100644 index 000000000000..1e8704533bc5 --- /dev/null +++ b/drivers/mmc/host/ricoh_mmc.c @@ -0,0 +1,151 @@ +/* + * ricoh_mmc.c - Dummy driver to disable the Rioch MMC controller. + * + * Copyright (C) 2007 Philip Langdale, All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or (at + * your option) any later version. + */ + +/* + * This is a conceptually ridiculous driver, but it is required by the way + * the Ricoh multi-function R5C832 works. This chip implements firewire + * and four different memory card controllers. Two of those controllers are + * an SDHCI controller and a proprietary MMC controller. The linux SDHCI + * driver supports MMC cards but the chip detects MMC cards in hardware + * and directs them to the MMC controller - so the SDHCI driver never sees + * them. To get around this, we must disable the useless MMC controller. + * At that point, the SDHCI controller will start seeing them. As a bonus, + * a detection event occurs immediately, even if the MMC card is already + * in the reader. + * + * The relevant registers live on the firewire function, so this is unavoidably + * ugly. Such is life. + */ + +#include <linux/pci.h> + +#define DRIVER_NAME "ricoh-mmc" + +static const struct pci_device_id pci_ids[] __devinitdata = { + { + .vendor = PCI_VENDOR_ID_RICOH, + .device = PCI_DEVICE_ID_RICOH_R5C843, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + }, + { /* end: all zeroes */ }, +}; + +MODULE_DEVICE_TABLE(pci, pci_ids); + +static int __devinit ricoh_mmc_probe(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + u8 rev; + + struct pci_dev *fw_dev = NULL; + + BUG_ON(pdev == NULL); + BUG_ON(ent == NULL); + + pci_read_config_byte(pdev, PCI_CLASS_REVISION, &rev); + + printk(KERN_INFO DRIVER_NAME + ": Ricoh MMC controller found at %s [%04x:%04x] (rev %x)\n", + pci_name(pdev), (int)pdev->vendor, (int)pdev->device, + (int)rev); + + while ((fw_dev = pci_get_device(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, fw_dev))) { + if (PCI_SLOT(pdev->devfn) == PCI_SLOT(fw_dev->devfn) && + pdev->bus == fw_dev->bus) { + u8 write_enable; + u8 disable; + + pci_read_config_byte(fw_dev, 0xCB, &disable); + if (disable & 0x02) { + printk(KERN_INFO DRIVER_NAME + ": Controller already disabled. Nothing to do.\n"); + return -ENODEV; + } + + pci_read_config_byte(fw_dev, 0xCA, &write_enable); + pci_write_config_byte(fw_dev, 0xCA, 0x57); + pci_write_config_byte(fw_dev, 0xCB, disable | 0x02); + pci_write_config_byte(fw_dev, 0xCA, write_enable); + + pci_set_drvdata(pdev, fw_dev); + + printk(KERN_INFO DRIVER_NAME + ": Controller is now disabled.\n"); + + break; + } + } + + if (pci_get_drvdata(pdev) == NULL) { + printk(KERN_WARNING DRIVER_NAME + ": Main firewire function not found. Cannot disable controller.\n"); + return -ENODEV; + } + + return 0; +} + +static void __devexit ricoh_mmc_remove(struct pci_dev *pdev) +{ + u8 write_enable; + u8 disable; + struct pci_dev *fw_dev = NULL; + + fw_dev = pci_get_drvdata(pdev); + BUG_ON(fw_dev == NULL); + + pci_read_config_byte(fw_dev, 0xCA, &write_enable); + pci_read_config_byte(fw_dev, 0xCB, &disable); + pci_write_config_byte(fw_dev, 0xCA, 0x57); + pci_write_config_byte(fw_dev, 0xCB, disable & ~0x02); + pci_write_config_byte(fw_dev, 0xCA, write_enable); + + printk(KERN_INFO DRIVER_NAME + ": Controller is now re-enabled.\n"); + + pci_set_drvdata(pdev, NULL); +} + +static struct pci_driver ricoh_mmc_driver = { + .name = DRIVER_NAME, + .id_table = pci_ids, + .probe = ricoh_mmc_probe, + .remove = __devexit_p(ricoh_mmc_remove), +}; + +/*****************************************************************************\ + * * + * Driver init/exit * + * * +\*****************************************************************************/ + +static int __init ricoh_mmc_drv_init(void) +{ + printk(KERN_INFO DRIVER_NAME + ": Ricoh MMC Controller disabling driver\n"); + printk(KERN_INFO DRIVER_NAME ": Copyright(c) Philip Langdale\n"); + + return pci_register_driver(&ricoh_mmc_driver); +} + +static void __exit ricoh_mmc_drv_exit(void) +{ + pci_unregister_driver(&ricoh_mmc_driver); +} + +module_init(ricoh_mmc_drv_init); +module_exit(ricoh_mmc_drv_exit); + +MODULE_AUTHOR("Philip Langdale <philipl@alumni.utexas.net>"); +MODULE_DESCRIPTION("Ricoh MMC Controller disabling driver"); +MODULE_LICENSE("GPL"); + diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index 20a7d89e01ba..b397121b947d 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -25,8 +25,6 @@ #define DBG(f, x...) \ pr_debug(DRIVER_NAME " [%s()]: " f, __func__,## x) -static unsigned int debug_nodma = 0; -static unsigned int debug_forcedma = 0; static unsigned int debug_quirks = 0; #define SDHCI_QUIRK_CLOCK_BEFORE_RESET (1<<0) @@ -35,6 +33,7 @@ static unsigned int debug_quirks = 0; #define SDHCI_QUIRK_NO_CARD_NO_RESET (1<<2) #define SDHCI_QUIRK_SINGLE_POWER_WRITE (1<<3) #define SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS (1<<4) +#define SDHCI_QUIRK_BROKEN_DMA (1<<5) static const struct pci_device_id pci_ids[] __devinitdata = { { @@ -68,7 +67,8 @@ static const struct pci_device_id pci_ids[] __devinitdata = { .device = PCI_DEVICE_ID_ENE_CB712_SD, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE, + .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE | + SDHCI_QUIRK_BROKEN_DMA, }, { @@ -76,7 +76,8 @@ static const struct pci_device_id pci_ids[] __devinitdata = { .device = PCI_DEVICE_ID_ENE_CB712_SD_2, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE, + .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE | + SDHCI_QUIRK_BROKEN_DMA, }, { @@ -132,7 +133,7 @@ static void sdhci_dumpregs(struct sdhci_host *host) readb(host->ioaddr + SDHCI_POWER_CONTROL), readb(host->ioaddr + SDHCI_BLOCK_GAP_CONTROL)); printk(KERN_DEBUG DRIVER_NAME ": Wake-up: 0x%08x | Clock: 0x%08x\n", - readb(host->ioaddr + SDHCI_WALK_UP_CONTROL), + readb(host->ioaddr + SDHCI_WAKE_UP_CONTROL), readw(host->ioaddr + SDHCI_CLOCK_CONTROL)); printk(KERN_DEBUG DRIVER_NAME ": Timeout: 0x%08x | Int stat: 0x%08x\n", readb(host->ioaddr + SDHCI_TIMEOUT_CONTROL), @@ -481,16 +482,16 @@ static void sdhci_finish_data(struct sdhci_host *host) * Controller doesn't count down when in single block mode. */ if (data->blocks == 1) - blocks = (data->error == MMC_ERR_NONE) ? 0 : 1; + blocks = (data->error == 0) ? 0 : 1; else blocks = readw(host->ioaddr + SDHCI_BLOCK_COUNT); data->bytes_xfered = data->blksz * (data->blocks - blocks); - if ((data->error == MMC_ERR_NONE) && blocks) { + if (!data->error && blocks) { printk(KERN_ERR "%s: Controller signalled completion even " "though there were blocks left.\n", mmc_hostname(host->mmc)); - data->error = MMC_ERR_FAILED; + data->error = -EIO; } if (data->stop) { @@ -498,7 +499,7 @@ static void sdhci_finish_data(struct sdhci_host *host) * The controller needs a reset of internal state machines * upon error conditions. */ - if (data->error != MMC_ERR_NONE) { + if (data->error) { sdhci_reset(host, SDHCI_RESET_CMD); sdhci_reset(host, SDHCI_RESET_DATA); } @@ -533,7 +534,7 @@ static void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd) printk(KERN_ERR "%s: Controller never released " "inhibit bit(s).\n", mmc_hostname(host->mmc)); sdhci_dumpregs(host); - cmd->error = MMC_ERR_FAILED; + cmd->error = -EIO; tasklet_schedule(&host->finish_tasklet); return; } @@ -554,7 +555,7 @@ static void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd) if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) { printk(KERN_ERR "%s: Unsupported response type!\n", mmc_hostname(host->mmc)); - cmd->error = MMC_ERR_INVALID; + cmd->error = -EINVAL; tasklet_schedule(&host->finish_tasklet); return; } @@ -601,7 +602,7 @@ static void sdhci_finish_command(struct sdhci_host *host) } } - host->cmd->error = MMC_ERR_NONE; + host->cmd->error = 0; if (host->data && host->data_early) sdhci_finish_data(host); @@ -722,7 +723,7 @@ static void sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq) host->mrq = mrq; if (!(readl(host->ioaddr + SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT)) { - host->mrq->cmd->error = MMC_ERR_TIMEOUT; + host->mrq->cmd->error = -ENOMEDIUM; tasklet_schedule(&host->finish_tasklet); } else sdhci_send_command(host, mrq->cmd); @@ -800,10 +801,35 @@ static int sdhci_get_ro(struct mmc_host *mmc) return !(present & SDHCI_WRITE_PROTECT); } +static void sdhci_enable_sdio_irq(struct mmc_host *mmc, int enable) +{ + struct sdhci_host *host; + unsigned long flags; + u32 ier; + + host = mmc_priv(mmc); + + spin_lock_irqsave(&host->lock, flags); + + ier = readl(host->ioaddr + SDHCI_INT_ENABLE); + + ier &= ~SDHCI_INT_CARD_INT; + if (enable) + ier |= SDHCI_INT_CARD_INT; + + writel(ier, host->ioaddr + SDHCI_INT_ENABLE); + writel(ier, host->ioaddr + SDHCI_SIGNAL_ENABLE); + + mmiowb(); + + spin_unlock_irqrestore(&host->lock, flags); +} + static const struct mmc_host_ops sdhci_ops = { .request = sdhci_request, .set_ios = sdhci_set_ios, .get_ro = sdhci_get_ro, + .enable_sdio_irq = sdhci_enable_sdio_irq, }; /*****************************************************************************\ @@ -831,7 +857,7 @@ static void sdhci_tasklet_card(unsigned long param) sdhci_reset(host, SDHCI_RESET_CMD); sdhci_reset(host, SDHCI_RESET_DATA); - host->mrq->cmd->error = MMC_ERR_FAILED; + host->mrq->cmd->error = -ENOMEDIUM; tasklet_schedule(&host->finish_tasklet); } } @@ -859,9 +885,9 @@ static void sdhci_tasklet_finish(unsigned long param) * The controller needs a reset of internal state machines * upon error conditions. */ - if ((mrq->cmd->error != MMC_ERR_NONE) || - (mrq->data && ((mrq->data->error != MMC_ERR_NONE) || - (mrq->data->stop && (mrq->data->stop->error != MMC_ERR_NONE))))) { + if (mrq->cmd->error || + (mrq->data && (mrq->data->error || + (mrq->data->stop && mrq->data->stop->error)))) { /* Some controllers need this kick or reset won't work here */ if (host->chip->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET) { @@ -906,13 +932,13 @@ static void sdhci_timeout_timer(unsigned long data) sdhci_dumpregs(host); if (host->data) { - host->data->error = MMC_ERR_TIMEOUT; + host->data->error = -ETIMEDOUT; sdhci_finish_data(host); } else { if (host->cmd) - host->cmd->error = MMC_ERR_TIMEOUT; + host->cmd->error = -ETIMEDOUT; else - host->mrq->cmd->error = MMC_ERR_TIMEOUT; + host->mrq->cmd->error = -ETIMEDOUT; tasklet_schedule(&host->finish_tasklet); } @@ -941,13 +967,12 @@ static void sdhci_cmd_irq(struct sdhci_host *host, u32 intmask) } if (intmask & SDHCI_INT_TIMEOUT) - host->cmd->error = MMC_ERR_TIMEOUT; - else if (intmask & SDHCI_INT_CRC) - host->cmd->error = MMC_ERR_BADCRC; - else if (intmask & (SDHCI_INT_END_BIT | SDHCI_INT_INDEX)) - host->cmd->error = MMC_ERR_FAILED; + host->cmd->error = -ETIMEDOUT; + else if (intmask & (SDHCI_INT_CRC | SDHCI_INT_END_BIT | + SDHCI_INT_INDEX)) + host->cmd->error = -EILSEQ; - if (host->cmd->error != MMC_ERR_NONE) + if (host->cmd->error) tasklet_schedule(&host->finish_tasklet); else if (intmask & SDHCI_INT_RESPONSE) sdhci_finish_command(host); @@ -974,13 +999,11 @@ static void sdhci_data_irq(struct sdhci_host *host, u32 intmask) } if (intmask & SDHCI_INT_DATA_TIMEOUT) - host->data->error = MMC_ERR_TIMEOUT; - else if (intmask & SDHCI_INT_DATA_CRC) - host->data->error = MMC_ERR_BADCRC; - else if (intmask & SDHCI_INT_DATA_END_BIT) - host->data->error = MMC_ERR_FAILED; + host->data->error = -ETIMEDOUT; + else if (intmask & (SDHCI_INT_DATA_CRC | SDHCI_INT_DATA_END_BIT)) + host->data->error = -EILSEQ; - if (host->data->error != MMC_ERR_NONE) + if (host->data->error) sdhci_finish_data(host); else { if (intmask & (SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL)) @@ -1015,6 +1038,7 @@ static irqreturn_t sdhci_irq(int irq, void *dev_id) irqreturn_t result; struct sdhci_host* host = dev_id; u32 intmask; + int cardint = 0; spin_lock(&host->lock); @@ -1059,6 +1083,11 @@ static irqreturn_t sdhci_irq(int irq, void *dev_id) intmask &= ~SDHCI_INT_BUS_POWER; + if (intmask & SDHCI_INT_CARD_INT) + cardint = 1; + + intmask &= ~SDHCI_INT_CARD_INT; + if (intmask) { printk(KERN_ERR "%s: Unexpected interrupt 0x%08x.\n", mmc_hostname(host->mmc), intmask); @@ -1073,6 +1102,12 @@ static irqreturn_t sdhci_irq(int irq, void *dev_id) out: spin_unlock(&host->lock); + /* + * We have to delay this as it calls back into the driver. + */ + if (cardint) + mmc_signal_sdio_irq(host->mmc); + return result; } @@ -1258,20 +1293,26 @@ static int __devinit sdhci_probe_slot(struct pci_dev *pdev, int slot) caps = readl(host->ioaddr + SDHCI_CAPABILITIES); - if (debug_nodma) - DBG("DMA forced off\n"); - else if (debug_forcedma) { - DBG("DMA forced on\n"); - host->flags |= SDHCI_USE_DMA; - } else if (chip->quirks & SDHCI_QUIRK_FORCE_DMA) + if (chip->quirks & SDHCI_QUIRK_FORCE_DMA) host->flags |= SDHCI_USE_DMA; - else if ((pdev->class & 0x0000FF) != PCI_SDHCI_IFDMA) - DBG("Controller doesn't have DMA interface\n"); else if (!(caps & SDHCI_CAN_DO_DMA)) DBG("Controller doesn't have DMA capability\n"); else host->flags |= SDHCI_USE_DMA; + if ((chip->quirks & SDHCI_QUIRK_BROKEN_DMA) && + (host->flags & SDHCI_USE_DMA)) { + DBG("Disabling DMA as it is marked broken"); + host->flags &= ~SDHCI_USE_DMA; + } + + if (((pdev->class & 0x0000FF) != PCI_SDHCI_IFDMA) && + (host->flags & SDHCI_USE_DMA)) { + printk(KERN_WARNING "%s: Will use DMA " + "mode even though HW doesn't fully " + "claim to support it.\n", host->slot_descr); + } + if (host->flags & SDHCI_USE_DMA) { if (pci_set_dma_mask(pdev, DMA_32BIT_MASK)) { printk(KERN_WARNING "%s: No suitable DMA available. " @@ -1312,7 +1353,7 @@ static int __devinit sdhci_probe_slot(struct pci_dev *pdev, int slot) mmc->ops = &sdhci_ops; mmc->f_min = host->max_clk / 256; mmc->f_max = host->max_clk; - mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_MULTIWRITE | MMC_CAP_BYTEBLOCK; + mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_MULTIWRITE | MMC_CAP_SDIO_IRQ; if (caps & SDHCI_CAN_DO_HISPD) mmc->caps |= MMC_CAP_SD_HIGHSPEED; @@ -1565,14 +1606,10 @@ static void __exit sdhci_drv_exit(void) module_init(sdhci_drv_init); module_exit(sdhci_drv_exit); -module_param(debug_nodma, uint, 0444); -module_param(debug_forcedma, uint, 0444); module_param(debug_quirks, uint, 0444); MODULE_AUTHOR("Pierre Ossman <drzeus@drzeus.cx>"); MODULE_DESCRIPTION("Secure Digital Host Controller Interface driver"); MODULE_LICENSE("GPL"); -MODULE_PARM_DESC(debug_nodma, "Forcefully disable DMA transfers. (default 0)"); -MODULE_PARM_DESC(debug_forcedma, "Forcefully enable DMA transfers. (default 0)"); MODULE_PARM_DESC(debug_quirks, "Force certain quirks."); diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h index e28987d6d2eb..05195ea900f4 100644 --- a/drivers/mmc/host/sdhci.h +++ b/drivers/mmc/host/sdhci.h @@ -81,7 +81,7 @@ #define SDHCI_BLOCK_GAP_CONTROL 0x2A -#define SDHCI_WALK_UP_CONTROL 0x2B +#define SDHCI_WAKE_UP_CONTROL 0x2B #define SDHCI_CLOCK_CONTROL 0x2C #define SDHCI_DIVIDER_SHIFT 8 diff --git a/drivers/mmc/host/tifm_sd.c b/drivers/mmc/host/tifm_sd.c index 8b736e968447..9b904795eb77 100644 --- a/drivers/mmc/host/tifm_sd.c +++ b/drivers/mmc/host/tifm_sd.c @@ -16,6 +16,7 @@ #include <linux/mmc/host.h> #include <linux/highmem.h> #include <linux/scatterlist.h> +#include <linux/log2.h> #include <asm/io.h> #define DRIVER_NAME "tifm_sd" @@ -404,14 +405,14 @@ static void tifm_sd_check_status(struct tifm_sd *host) struct tifm_dev *sock = host->dev; struct mmc_command *cmd = host->req->cmd; - if (cmd->error != MMC_ERR_NONE) + if (cmd->error) goto finish_request; if (!(host->cmd_flags & CMD_READY)) return; if (cmd->data) { - if (cmd->data->error != MMC_ERR_NONE) { + if (cmd->data->error) { if ((host->cmd_flags & SCMD_ACTIVE) && !(host->cmd_flags & SCMD_READY)) return; @@ -504,7 +505,7 @@ static void tifm_sd_card_event(struct tifm_dev *sock) { struct tifm_sd *host; unsigned int host_status = 0; - int cmd_error = MMC_ERR_NONE; + int cmd_error = 0; struct mmc_command *cmd = NULL; unsigned long flags; @@ -521,15 +522,15 @@ static void tifm_sd_card_event(struct tifm_dev *sock) writel(host_status & TIFM_MMCSD_ERRMASK, sock->addr + SOCK_MMCSD_STATUS); if (host_status & TIFM_MMCSD_CTO) - cmd_error = MMC_ERR_TIMEOUT; + cmd_error = -ETIMEDOUT; else if (host_status & TIFM_MMCSD_CCRC) - cmd_error = MMC_ERR_BADCRC; + cmd_error = -EILSEQ; if (cmd->data) { if (host_status & TIFM_MMCSD_DTO) - cmd->data->error = MMC_ERR_TIMEOUT; + cmd->data->error = -ETIMEDOUT; else if (host_status & TIFM_MMCSD_DCRC) - cmd->data->error = MMC_ERR_BADCRC; + cmd->data->error = -EILSEQ; } writel(TIFM_FIFO_INT_SETALL, @@ -626,14 +627,21 @@ static void tifm_sd_request(struct mmc_host *mmc, struct mmc_request *mrq) spin_lock_irqsave(&sock->lock, flags); if (host->eject) { - spin_unlock_irqrestore(&sock->lock, flags); + mrq->cmd->error = -ENOMEDIUM; goto err_out; } if (host->req) { printk(KERN_ERR "%s : unfinished request detected\n", sock->dev.bus_id); - spin_unlock_irqrestore(&sock->lock, flags); + mrq->cmd->error = -ETIMEDOUT; + goto err_out; + } + + if (mrq->data && !is_power_of_2(mrq->data->blksz)) { + printk(KERN_ERR "%s: Unsupported block size (%d bytes)\n", + sock->dev.bus_id, mrq->data->blksz); + mrq->cmd->error = -EINVAL; goto err_out; } @@ -722,7 +730,7 @@ static void tifm_sd_request(struct mmc_host *mmc, struct mmc_request *mrq) return; err_out: - mrq->cmd->error = MMC_ERR_TIMEOUT; + spin_unlock_irqrestore(&sock->lock, flags); mmc_request_done(mmc, mrq); } @@ -1012,9 +1020,9 @@ static void tifm_sd_remove(struct tifm_dev *sock) writel(TIFM_FIFO_INT_SETALL, sock->addr + SOCK_DMA_FIFO_INT_ENABLE_CLEAR); writel(0, sock->addr + SOCK_DMA_FIFO_INT_ENABLE_SET); - host->req->cmd->error = MMC_ERR_TIMEOUT; + host->req->cmd->error = -ENOMEDIUM; if (host->req->stop) - host->req->stop->error = MMC_ERR_TIMEOUT; + host->req->stop->error = -ENOMEDIUM; tasklet_schedule(&host->finish_tasklet); } spin_unlock_irqrestore(&sock->lock, flags); diff --git a/drivers/mmc/host/wbsd.c b/drivers/mmc/host/wbsd.c index 9bf2a877113b..80db11c05f2a 100644 --- a/drivers/mmc/host/wbsd.c +++ b/drivers/mmc/host/wbsd.c @@ -317,7 +317,7 @@ static inline void wbsd_get_short_reply(struct wbsd_host *host, * Correct response type? */ if (wbsd_read_index(host, WBSD_IDX_RSPLEN) != WBSD_RSP_SHORT) { - cmd->error = MMC_ERR_INVALID; + cmd->error = -EILSEQ; return; } @@ -337,7 +337,7 @@ static inline void wbsd_get_long_reply(struct wbsd_host *host, * Correct response type? */ if (wbsd_read_index(host, WBSD_IDX_RSPLEN) != WBSD_RSP_LONG) { - cmd->error = MMC_ERR_INVALID; + cmd->error = -EILSEQ; return; } @@ -372,7 +372,7 @@ static void wbsd_send_command(struct wbsd_host *host, struct mmc_command *cmd) for (i = 3; i >= 0; i--) outb((cmd->arg >> (i * 8)) & 0xff, host->base + WBSD_CMDR); - cmd->error = MMC_ERR_NONE; + cmd->error = 0; /* * Wait for the request to complete. @@ -392,13 +392,13 @@ static void wbsd_send_command(struct wbsd_host *host, struct mmc_command *cmd) /* Card removed? */ if (isr & WBSD_INT_CARD) - cmd->error = MMC_ERR_TIMEOUT; + cmd->error = -ENOMEDIUM; /* Timeout? */ else if (isr & WBSD_INT_TIMEOUT) - cmd->error = MMC_ERR_TIMEOUT; + cmd->error = -ETIMEDOUT; /* CRC? */ else if ((cmd->flags & MMC_RSP_CRC) && (isr & WBSD_INT_CRC)) - cmd->error = MMC_ERR_BADCRC; + cmd->error = -EILSEQ; /* All ok */ else { if (cmd->flags & MMC_RSP_136) @@ -585,7 +585,7 @@ static void wbsd_prepare_data(struct wbsd_host *host, struct mmc_data *data) ((blksize >> 4) & 0xF0) | WBSD_DATA_WIDTH); wbsd_write_index(host, WBSD_IDX_PBSLSB, blksize & 0xFF); } else { - data->error = MMC_ERR_INVALID; + data->error = -EINVAL; return; } @@ -607,7 +607,7 @@ static void wbsd_prepare_data(struct wbsd_host *host, struct mmc_data *data) */ BUG_ON(size > 0x10000); if (size > 0x10000) { - data->error = MMC_ERR_INVALID; + data->error = -EINVAL; return; } @@ -669,7 +669,7 @@ static void wbsd_prepare_data(struct wbsd_host *host, struct mmc_data *data) } } - data->error = MMC_ERR_NONE; + data->error = 0; } static void wbsd_finish_data(struct wbsd_host *host, struct mmc_data *data) @@ -724,8 +724,8 @@ static void wbsd_finish_data(struct wbsd_host *host, struct mmc_data *data) "%d bytes left.\n", mmc_hostname(host->mmc), count); - if (data->error == MMC_ERR_NONE) - data->error = MMC_ERR_FAILED; + if (!data->error) + data->error = -EIO; } else { /* * Transfer data from DMA buffer to @@ -735,7 +735,7 @@ static void wbsd_finish_data(struct wbsd_host *host, struct mmc_data *data) wbsd_dma_to_sg(host, data); } - if (data->error != MMC_ERR_NONE) { + if (data->error) { if (data->bytes_xfered) data->bytes_xfered -= data->blksz; } @@ -767,11 +767,10 @@ static void wbsd_request(struct mmc_host *mmc, struct mmc_request *mrq) host->mrq = mrq; /* - * If there is no card in the slot then - * timeout immediatly. + * Check that there is actually a card in the slot. */ if (!(host->flags & WBSD_FCARD_PRESENT)) { - cmd->error = MMC_ERR_TIMEOUT; + cmd->error = -ENOMEDIUM; goto done; } @@ -807,7 +806,7 @@ static void wbsd_request(struct mmc_host *mmc, struct mmc_request *mrq) "supported by this controller.\n", mmc_hostname(host->mmc), cmd->opcode); #endif - cmd->error = MMC_ERR_INVALID; + cmd->error = -EINVAL; goto done; }; @@ -819,7 +818,7 @@ static void wbsd_request(struct mmc_host *mmc, struct mmc_request *mrq) if (cmd->data) { wbsd_prepare_data(host, cmd->data); - if (cmd->data->error != MMC_ERR_NONE) + if (cmd->data->error) goto done; } @@ -830,7 +829,7 @@ static void wbsd_request(struct mmc_host *mmc, struct mmc_request *mrq) * will be finished after the data has * transfered. */ - if (cmd->data && (cmd->error == MMC_ERR_NONE)) { + if (cmd->data && !cmd->error) { /* * Dirty fix for hardware bug. */ @@ -1033,7 +1032,7 @@ static void wbsd_tasklet_card(unsigned long param) mmc_hostname(host->mmc)); wbsd_reset(host); - host->mrq->cmd->error = MMC_ERR_FAILED; + host->mrq->cmd->error = -ENOMEDIUM; tasklet_schedule(&host->finish_tasklet); } @@ -1097,7 +1096,7 @@ static void wbsd_tasklet_crc(unsigned long param) DBGF("CRC error\n"); - data->error = MMC_ERR_BADCRC; + data->error = -EILSEQ; tasklet_schedule(&host->finish_tasklet); @@ -1121,7 +1120,7 @@ static void wbsd_tasklet_timeout(unsigned long param) DBGF("Timeout\n"); - data->error = MMC_ERR_TIMEOUT; + data->error = -ETIMEDOUT; tasklet_schedule(&host->finish_tasklet); @@ -1220,7 +1219,7 @@ static int __devinit wbsd_alloc_mmc(struct device *dev) mmc->f_min = 375000; mmc->f_max = 24000000; mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; - mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_MULTIWRITE | MMC_CAP_BYTEBLOCK; + mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_MULTIWRITE; spin_lock_init(&host->lock); |
