diff options
Diffstat (limited to 'drivers/input/misc')
| -rw-r--r-- | drivers/input/misc/Kconfig | 40 | ||||
| -rw-r--r-- | drivers/input/misc/Makefile | 4 | ||||
| -rw-r--r-- | drivers/input/misc/ad714x-i2c.c | 140 | ||||
| -rw-r--r-- | drivers/input/misc/ad714x-spi.c | 103 | ||||
| -rw-r--r-- | drivers/input/misc/ad714x.c | 1347 | ||||
| -rw-r--r-- | drivers/input/misc/ad714x.h | 26 | ||||
| -rw-r--r-- | drivers/input/misc/pcf8574_keypad.c | 227 |
7 files changed, 1887 insertions, 0 deletions
diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig index 23140a3bb8e0..48cdabec372a 100644 --- a/drivers/input/misc/Kconfig +++ b/drivers/input/misc/Kconfig @@ -22,6 +22,36 @@ config INPUT_88PM860X_ONKEY To compile this driver as a module, choose M here: the module will be called 88pm860x_onkey. +config INPUT_AD714X + tristate "Analog Devices AD714x Capacitance Touch Sensor" + help + Say Y here if you want to support an AD7142/3/7/8/7A touch sensor. + + You should select a bus connection too. + + To compile this driver as a module, choose M here: the + module will be called ad714x. + +config INPUT_AD714X_I2C + tristate "support I2C bus connection" + depends on INPUT_AD714X && I2C + default y + help + Say Y here if you have AD7142/AD7147 hooked to an I2C bus. + + To compile this driver as a module, choose M here: the + module will be called ad714x-i2c. + +config INPUT_AD714X_SPI + tristate "support SPI bus connection" + depends on INPUT_AD714X && SPI + default y + help + Say Y here if you have AD7142/AD7147 hooked to a SPI bus. + + To compile this driver as a module, choose M here: the + module will be called ad714x-spi. + config INPUT_PCSPKR tristate "PC Speaker support" depends on PCSPKR_PLATFORM @@ -277,6 +307,16 @@ config INPUT_PCF50633_PMU Say Y to include support for delivering PMU events via input layer on NXP PCF50633. +config INPUT_PCF8574 + tristate "PCF8574 Keypad input device" + depends on I2C && EXPERIMENTAL + help + Say Y here if you want to support a keypad connetced via I2C + with a PCF8574. + + To compile this driver as a module, choose M here: the + module will be called pcf8574_keypad. + config INPUT_GPIO_ROTARY_ENCODER tristate "Rotary encoders connected to GPIO pins" depends on GPIOLIB && GENERIC_GPIO diff --git a/drivers/input/misc/Makefile b/drivers/input/misc/Makefile index 7e95a5d474dc..f9f577031e06 100644 --- a/drivers/input/misc/Makefile +++ b/drivers/input/misc/Makefile @@ -5,6 +5,9 @@ # Each configuration option enables a list of files. obj-$(CONFIG_INPUT_88PM860X_ONKEY) += 88pm860x_onkey.o +obj-$(CONFIG_INPUT_AD714X) += ad714x.o +obj-$(CONFIG_INPUT_AD714X_I2C) += ad714x-i2c.o +obj-$(CONFIG_INPUT_AD714X_SPI) += ad714x-spi.o obj-$(CONFIG_INPUT_APANEL) += apanel.o obj-$(CONFIG_INPUT_ATI_REMOTE) += ati_remote.o obj-$(CONFIG_INPUT_ATI_REMOTE2) += ati_remote2.o @@ -19,6 +22,7 @@ obj-$(CONFIG_INPUT_KEYSPAN_REMOTE) += keyspan_remote.o obj-$(CONFIG_INPUT_M68K_BEEP) += m68kspkr.o obj-$(CONFIG_INPUT_PCAP) += pcap_keys.o obj-$(CONFIG_INPUT_PCF50633_PMU) += pcf50633-input.o +obj-$(CONFIG_INPUT_PCF8574) += pcf8574_keypad.o obj-$(CONFIG_INPUT_PCSPKR) += pcspkr.o obj-$(CONFIG_INPUT_POWERMATE) += powermate.o obj-$(CONFIG_INPUT_RB532_BUTTON) += rb532_button.o diff --git a/drivers/input/misc/ad714x-i2c.c b/drivers/input/misc/ad714x-i2c.c new file mode 100644 index 000000000000..e9adbe49f6a4 --- /dev/null +++ b/drivers/input/misc/ad714x-i2c.c @@ -0,0 +1,140 @@ +/* + * AD714X CapTouch Programmable Controller driver (I2C bus) + * + * Copyright 2009 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include <linux/input.h> /* BUS_I2C */ +#include <linux/i2c.h> +#include <linux/module.h> +#include <linux/types.h> +#include "ad714x.h" + +#ifdef CONFIG_PM +static int ad714x_i2c_suspend(struct i2c_client *client, pm_message_t message) +{ + return ad714x_disable(i2c_get_clientdata(client)); +} + +static int ad714x_i2c_resume(struct i2c_client *client) +{ + return ad714x_enable(i2c_get_clientdata(client)); +} +#else +# define ad714x_i2c_suspend NULL +# define ad714x_i2c_resume NULL +#endif + +static int ad714x_i2c_write(struct device *dev, unsigned short reg, + unsigned short data) +{ + struct i2c_client *client = to_i2c_client(dev); + int ret = 0; + u8 *_reg = (u8 *)® + u8 *_data = (u8 *)&data; + + u8 tx[4] = { + _reg[1], + _reg[0], + _data[1], + _data[0] + }; + + ret = i2c_master_send(client, tx, 4); + if (ret < 0) + dev_err(&client->dev, "I2C write error\n"); + + return ret; +} + +static int ad714x_i2c_read(struct device *dev, unsigned short reg, + unsigned short *data) +{ + struct i2c_client *client = to_i2c_client(dev); + int ret = 0; + u8 *_reg = (u8 *)® + u8 *_data = (u8 *)data; + + u8 tx[2] = { + _reg[1], + _reg[0] + }; + u8 rx[2]; + + ret = i2c_master_send(client, tx, 2); + if (ret >= 0) + ret = i2c_master_recv(client, rx, 2); + + if (unlikely(ret < 0)) { + dev_err(&client->dev, "I2C read error\n"); + } else { + _data[0] = rx[1]; + _data[1] = rx[0]; + } + + return ret; +} + +static int __devinit ad714x_i2c_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct ad714x_chip *chip; + + chip = ad714x_probe(&client->dev, BUS_I2C, client->irq, + ad714x_i2c_read, ad714x_i2c_write); + if (IS_ERR(chip)) + return PTR_ERR(chip); + + i2c_set_clientdata(client, chip); + + return 0; +} + +static int __devexit ad714x_i2c_remove(struct i2c_client *client) +{ + struct ad714x_chip *chip = i2c_get_clientdata(client); + + ad714x_remove(chip); + i2c_set_clientdata(client, NULL); + + return 0; +} + +static const struct i2c_device_id ad714x_id[] = { + { "ad7142_captouch", 0 }, + { "ad7143_captouch", 0 }, + { "ad7147_captouch", 0 }, + { "ad7147a_captouch", 0 }, + { "ad7148_captouch", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, ad714x_id); + +static struct i2c_driver ad714x_i2c_driver = { + .driver = { + .name = "ad714x_captouch", + }, + .probe = ad714x_i2c_probe, + .remove = __devexit_p(ad714x_i2c_remove), + .suspend = ad714x_i2c_suspend, + .resume = ad714x_i2c_resume, + .id_table = ad714x_id, +}; + +static __init int ad714x_i2c_init(void) +{ + return i2c_add_driver(&ad714x_i2c_driver); +} +module_init(ad714x_i2c_init); + +static __exit void ad714x_i2c_exit(void) +{ + i2c_del_driver(&ad714x_i2c_driver); +} +module_exit(ad714x_i2c_exit); + +MODULE_DESCRIPTION("Analog Devices AD714X Capacitance Touch Sensor I2C Bus Driver"); +MODULE_AUTHOR("Barry Song <21cnbao@gmail.com>"); +MODULE_LICENSE("GPL"); diff --git a/drivers/input/misc/ad714x-spi.c b/drivers/input/misc/ad714x-spi.c new file mode 100644 index 000000000000..7f8dedfd1bfe --- /dev/null +++ b/drivers/input/misc/ad714x-spi.c @@ -0,0 +1,103 @@ +/* + * AD714X CapTouch Programmable Controller driver (SPI bus) + * + * Copyright 2009 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include <linux/input.h> /* BUS_I2C */ +#include <linux/module.h> +#include <linux/spi/spi.h> +#include <linux/types.h> +#include "ad714x.h" + +#define AD714x_SPI_CMD_PREFIX 0xE000 /* bits 15:11 */ +#define AD714x_SPI_READ BIT(10) + +#ifdef CONFIG_PM +static int ad714x_spi_suspend(struct spi_device *spi, pm_message_t message) +{ + return ad714x_disable(spi_get_drvdata(spi)); +} + +static int ad714x_spi_resume(struct spi_device *spi) +{ + return ad714x_enable(spi_get_drvdata(spi)); +} +#else +# define ad714x_spi_suspend NULL +# define ad714x_spi_resume NULL +#endif + +static int ad714x_spi_read(struct device *dev, unsigned short reg, + unsigned short *data) +{ + struct spi_device *spi = to_spi_device(dev); + unsigned short tx = AD714x_SPI_CMD_PREFIX | AD714x_SPI_READ | reg; + + return spi_write_then_read(spi, (u8 *)&tx, 2, (u8 *)data, 2); +} + +static int ad714x_spi_write(struct device *dev, unsigned short reg, + unsigned short data) +{ + struct spi_device *spi = to_spi_device(dev); + unsigned short tx[2] = { + AD714x_SPI_CMD_PREFIX | reg, + data + }; + + return spi_write(spi, (u8 *)tx, 4); +} + +static int __devinit ad714x_spi_probe(struct spi_device *spi) +{ + struct ad714x_chip *chip; + + chip = ad714x_probe(&spi->dev, BUS_SPI, spi->irq, + ad714x_spi_read, ad714x_spi_write); + if (IS_ERR(chip)) + return PTR_ERR(chip); + + spi_set_drvdata(spi, chip); + + return 0; +} + +static int __devexit ad714x_spi_remove(struct spi_device *spi) +{ + struct ad714x_chip *chip = spi_get_drvdata(spi); + + ad714x_remove(chip); + spi_set_drvdata(spi, NULL); + + return 0; +} + +static struct spi_driver ad714x_spi_driver = { + .driver = { + .name = "ad714x_captouch", + .owner = THIS_MODULE, + }, + .probe = ad714x_spi_probe, + .remove = __devexit_p(ad714x_spi_remove), + .suspend = ad714x_spi_suspend, + .resume = ad714x_spi_resume, +}; + +static __init int ad714x_spi_init(void) +{ + return spi_register_driver(&ad714x_spi_driver); +} +module_init(ad714x_spi_init); + +static __exit void ad714x_spi_exit(void) +{ + spi_unregister_driver(&ad714x_spi_driver); +} +module_exit(ad714x_spi_exit); + +MODULE_DESCRIPTION("Analog Devices AD714X Capacitance Touch Sensor SPI Bus Driver"); +MODULE_AUTHOR("Barry Song <21cnbao@gmail.com>"); +MODULE_LICENSE("GPL"); diff --git a/drivers/input/misc/ad714x.c b/drivers/input/misc/ad714x.c new file mode 100644 index 000000000000..0fe27baf5e72 --- /dev/null +++ b/drivers/input/misc/ad714x.c @@ -0,0 +1,1347 @@ +/* + * AD714X CapTouch Programmable Controller driver supporting AD7142/3/7/8/7A + * + * Copyright 2009 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include <linux/device.h> +#include <linux/init.h> +#include <linux/input.h> +#include <linux/interrupt.h> +#include <linux/slab.h> +#include <linux/input/ad714x.h> +#include "ad714x.h" + +#define AD714X_PWR_CTRL 0x0 +#define AD714X_STG_CAL_EN_REG 0x1 +#define AD714X_AMB_COMP_CTRL0_REG 0x2 +#define AD714X_PARTID_REG 0x17 +#define AD7142_PARTID 0xE620 +#define AD7143_PARTID 0xE630 +#define AD7147_PARTID 0x1470 +#define AD7148_PARTID 0x1480 +#define AD714X_STAGECFG_REG 0x80 +#define AD714X_SYSCFG_REG 0x0 + +#define STG_LOW_INT_EN_REG 0x5 +#define STG_HIGH_INT_EN_REG 0x6 +#define STG_COM_INT_EN_REG 0x7 +#define STG_LOW_INT_STA_REG 0x8 +#define STG_HIGH_INT_STA_REG 0x9 +#define STG_COM_INT_STA_REG 0xA + +#define CDC_RESULT_S0 0xB +#define CDC_RESULT_S1 0xC +#define CDC_RESULT_S2 0xD +#define CDC_RESULT_S3 0xE +#define CDC_RESULT_S4 0xF +#define CDC_RESULT_S5 0x10 +#define CDC_RESULT_S6 0x11 +#define CDC_RESULT_S7 0x12 +#define CDC_RESULT_S8 0x13 +#define CDC_RESULT_S9 0x14 +#define CDC_RESULT_S10 0x15 +#define CDC_RESULT_S11 0x16 + +#define STAGE0_AMBIENT 0xF1 +#define STAGE1_AMBIENT 0x115 +#define STAGE2_AMBIENT 0x139 +#define STAGE3_AMBIENT 0x15D +#define STAGE4_AMBIENT 0x181 +#define STAGE5_AMBIENT 0x1A5 +#define STAGE6_AMBIENT 0x1C9 +#define STAGE7_AMBIENT 0x1ED +#define STAGE8_AMBIENT 0x211 +#define STAGE9_AMBIENT 0x234 +#define STAGE10_AMBIENT 0x259 +#define STAGE11_AMBIENT 0x27D + +#define PER_STAGE_REG_NUM 36 +#define STAGE_NUM 12 +#define STAGE_CFGREG_NUM 8 +#define SYS_CFGREG_NUM 8 + +/* + * driver information which will be used to maintain the software flow + */ +enum ad714x_device_state { IDLE, JITTER, ACTIVE, SPACE }; + +struct ad714x_slider_drv { + int highest_stage; + int abs_pos; + int flt_pos; + enum ad714x_device_state state; + struct input_dev *input; +}; + +struct ad714x_wheel_drv { + int abs_pos; + int flt_pos; + int pre_mean_value; + int pre_highest_stage; + int pre_mean_value_no_offset; + int mean_value; + int mean_value_no_offset; + int pos_offset; + int pos_ratio; + int highest_stage; + enum ad714x_device_state state; + struct input_dev *input; +}; + +struct ad714x_touchpad_drv { + int x_highest_stage; + int x_flt_pos; + int x_abs_pos; + int y_highest_stage; + int y_flt_pos; + int y_abs_pos; + int left_ep; + int left_ep_val; + int right_ep; + int right_ep_val; + int top_ep; + int top_ep_val; + int bottom_ep; + int bottom_ep_val; + enum ad714x_device_state state; + struct input_dev *input; +}; + +struct ad714x_button_drv { + enum ad714x_device_state state; + /* + * Unlike slider/wheel/touchpad, all buttons point to + * same input_dev instance + */ + struct input_dev *input; +}; + +struct ad714x_driver_data { + struct ad714x_slider_drv *slider; + struct ad714x_wheel_drv *wheel; + struct ad714x_touchpad_drv *touchpad; + struct ad714x_button_drv *button; +}; + +/* + * information to integrate all things which will be private data + * of spi/i2c device + */ +struct ad714x_chip { + unsigned short h_state; + unsigned short l_state; + unsigned short c_state; + unsigned short adc_reg[STAGE_NUM]; + unsigned short amb_reg[STAGE_NUM]; + unsigned short sensor_val[STAGE_NUM]; + + struct ad714x_platform_data *hw; + struct ad714x_driver_data *sw; + + int irq; + struct device *dev; + ad714x_read_t read; + ad714x_write_t write; + + struct mutex mutex; + + unsigned product; + unsigned version; +}; + +static void ad714x_use_com_int(struct ad714x_chip *ad714x, + int start_stage, int end_stage) +{ + unsigned short data; + unsigned short mask; + + mask = ((1 << (end_stage + 1)) - 1) - (1 << start_stage); + + ad714x->read(ad714x->dev, STG_COM_INT_EN_REG, &data); + data |= 1 << start_stage; + ad714x->write(ad714x->dev, STG_COM_INT_EN_REG, data); + + ad714x->read(ad714x->dev, STG_HIGH_INT_EN_REG, &data); + data &= ~mask; + ad714x->write(ad714x->dev, STG_HIGH_INT_EN_REG, data); +} + +static void ad714x_use_thr_int(struct ad714x_chip *ad714x, + int start_stage, int end_stage) +{ + unsigned short data; + unsigned short mask; + + mask = ((1 << (end_stage + 1)) - 1) - (1 << start_stage); + + ad714x->read(ad714x->dev, STG_COM_INT_EN_REG, &data); + data &= ~(1 << start_stage); + ad714x->write(ad714x->dev, STG_COM_INT_EN_REG, data); + + ad714x->read(ad714x->dev, STG_HIGH_INT_EN_REG, &data); + data |= mask; + ad714x->write(ad714x->dev, STG_HIGH_INT_EN_REG, data); +} + +static int ad714x_cal_highest_stage(struct ad714x_chip *ad714x, + int start_stage, int end_stage) +{ + int max_res = 0; + int max_idx = 0; + int i; + + for (i = start_stage; i <= end_stage; i++) { + if (ad714x->sensor_val[i] > max_res) { + max_res = ad714x->sensor_val[i]; + max_idx = i; + } + } + + return max_idx; +} + +static int ad714x_cal_abs_pos(struct ad714x_chip *ad714x, + int start_stage, int end_stage, + int highest_stage, int max_coord) +{ + int a_param, b_param; + + if (highest_stage == start_stage) { + a_param = ad714x->sensor_val[start_stage + 1]; + b_param = ad714x->sensor_val[start_stage] + + ad714x->sensor_val[start_stage + 1]; + } else if (highest_stage == end_stage) { + a_param = ad714x->sensor_val[end_stage] * + (end_stage - start_stage) + + ad714x->sensor_val[end_stage - 1] * + (end_stage - start_stage - 1); + b_param = ad714x->sensor_val[end_stage] + + ad714x->sensor_val[end_stage - 1]; + } else { + a_param = ad714x->sensor_val[highest_stage] * + (highest_stage - start_stage) + + ad714x->sensor_val[highest_stage - 1] * + (highest_stage - start_stage - 1) + + ad714x->sensor_val[highest_stage + 1] * + (highest_stage - start_stage + 1); + b_param = ad714x->sensor_val[highest_stage] + + ad714x->sensor_val[highest_stage - 1] + + ad714x->sensor_val[highest_stage + 1]; + } + + return (max_coord / (end_stage - start_stage)) * a_param / b_param; +} + +/* + * One button can connect to multi positive and negative of CDCs + * Multi-buttons can connect to same positive/negative of one CDC + */ +static void ad714x_button_state_machine(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_button_plat *hw = &ad714x->hw->button[idx]; + struct ad714x_button_drv *sw = &ad714x->sw->button[idx]; + + switch (sw->state) { + case IDLE: + if (((ad714x->h_state & hw->h_mask) == hw->h_mask) && + ((ad714x->l_state & hw->l_mask) == hw->l_mask)) { + dev_dbg(ad714x->dev, "button %d touched\n", idx); + input_report_key(sw->input, hw->keycode, 1); + input_sync(sw->input); + sw->state = ACTIVE; + } + break; + + case ACTIVE: + if (((ad714x->h_state & hw->h_mask) != hw->h_mask) || + ((ad714x->l_state & hw->l_mask) != hw->l_mask)) { + dev_dbg(ad714x->dev, "button %d released\n", idx); + input_report_key(sw->input, hw->keycode, 0); + input_sync(sw->input); + sw->state = IDLE; + } + break; + + default: + break; + } +} + +/* + * The response of a sensor is defined by the absolute number of codes + * between the current CDC value and the ambient value. + */ +static void ad714x_slider_cal_sensor_val(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_slider_plat *hw = &ad714x->hw->slider[idx]; + int i; + + for (i = hw->start_stage; i <= hw->end_stage; i++) { + ad714x->read(ad714x->dev, CDC_RESULT_S0 + i, + &ad714x->adc_reg[i]); + ad714x->read(ad714x->dev, + STAGE0_AMBIENT + i * PER_STAGE_REG_NUM, + &ad714x->amb_reg[i]); + + ad714x->sensor_val[i] = abs(ad714x->adc_reg[i] - + ad714x->amb_reg[i]); + } +} + +static void ad714x_slider_cal_highest_stage(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_slider_plat *hw = &ad714x->hw->slider[idx]; + struct ad714x_slider_drv *sw = &ad714x->sw->slider[idx]; + + sw->highest_stage = ad714x_cal_highest_stage(ad714x, hw->start_stage, + hw->end_stage); + + dev_dbg(ad714x->dev, "slider %d highest_stage:%d\n", idx, + sw->highest_stage); +} + +/* + * The formulae are very straight forward. It uses the sensor with the + * highest response and the 2 adjacent ones. + * When Sensor 0 has the highest response, only sensor 0 and sensor 1 + * are used in the calculations. Similarly when the last sensor has the + * highest response, only the last sensor and the second last sensors + * are used in the calculations. + * + * For i= idx_of_peak_Sensor-1 to i= idx_of_peak_Sensor+1 + * v += Sensor response(i)*i + * w += Sensor response(i) + * POS=(Number_of_Positions_Wanted/(Number_of_Sensors_Used-1)) *(v/w) + */ +static void ad714x_slider_cal_abs_pos(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_slider_plat *hw = &ad714x->hw->slider[idx]; + struct ad714x_slider_drv *sw = &ad714x->sw->slider[idx]; + + sw->abs_pos = ad714x_cal_abs_pos(ad714x, hw->start_stage, hw->end_stage, + sw->highest_stage, hw->max_coord); + + dev_dbg(ad714x->dev, "slider %d absolute position:%d\n", idx, + sw->abs_pos); +} + +/* + * To minimise the Impact of the noise on the algorithm, ADI developed a + * routine that filters the CDC results after they have been read by the + * host processor. + * The filter used is an Infinite Input Response(IIR) filter implemented + * in firmware and attenuates the noise on the CDC results after they've + * been read by the host processor. + * Filtered_CDC_result = (Filtered_CDC_result * (10 - Coefficient) + + * Latest_CDC_result * Coefficient)/10 + */ +static void ad714x_slider_cal_flt_pos(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_slider_drv *sw = &ad714x->sw->slider[idx]; + + sw->flt_pos = (sw->flt_pos * (10 - 4) + + sw->abs_pos * 4)/10; + + dev_dbg(ad714x->dev, "slider %d filter position:%d\n", idx, + sw->flt_pos); +} + +static void ad714x_slider_use_com_int(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_slider_plat *hw = &ad714x->hw->slider[idx]; + + ad714x_use_com_int(ad714x, hw->start_stage, hw->end_stage); +} + +static void ad714x_slider_use_thr_int(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_slider_plat *hw = &ad714x->hw->slider[idx]; + + ad714x_use_thr_int(ad714x, hw->start_stage, hw->end_stage); +} + +static void ad714x_slider_state_machine(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_slider_plat *hw = &ad714x->hw->slider[idx]; + struct ad714x_slider_drv *sw = &ad714x->sw->slider[idx]; + unsigned short h_state, c_state; + unsigned short mask; + + mask = ((1 << (hw->end_stage + 1)) - 1) - ((1 << hw->start_stage) - 1); + + h_state = ad714x->h_state & mask; + c_state = ad714x->c_state & mask; + + switch (sw->state) { + case IDLE: + if (h_state) { + sw->state = JITTER; + /* In End of Conversion interrupt mode, the AD714X + * continuously generates hardware interrupts. + */ + ad714x_slider_use_com_int(ad714x, idx); + dev_dbg(ad714x->dev, "slider %d touched\n", idx); + } + break; + + case JITTER: + if (c_state == mask) { + ad714x_slider_cal_sensor_val(ad714x, idx); + ad714x_slider_cal_highest_stage(ad714x, idx); + ad714x_slider_cal_abs_pos(ad714x, idx); + sw->flt_pos = sw->abs_pos; + sw->state = ACTIVE; + } + break; + + case ACTIVE: + if (c_state == mask) { + if (h_state) { + ad714x_slider_cal_sensor_val(ad714x, idx); + ad714x_slider_cal_highest_stage(ad714x, idx); + ad714x_slider_cal_abs_pos(ad714x, idx); + ad714x_slider_cal_flt_pos(ad714x, idx); + + input_report_abs(sw->input, ABS_X, sw->flt_pos); + input_report_key(sw->input, BTN_TOUCH, 1); + } else { + /* When the user lifts off the sensor, configure + * the AD714X back to threshold interrupt mode. + */ + ad714x_slider_use_thr_int(ad714x, idx); + sw->state = IDLE; + input_report_key(sw->input, BTN_TOUCH, 0); + dev_dbg(ad714x->dev, "slider %d released\n", + idx); + } + input_sync(sw->input); + } + break; + + default: + break; + } +} + +/* + * When the scroll wheel is activated, we compute the absolute position based + * on the sensor values. To calculate the position, we first determine the + * sensor that has the greatest response among the 8 sensors that constitutes + * the scrollwheel. Then we determined the 2 sensors on either sides of the + * sensor with the highest response and we apply weights to these sensors. + */ +static void ad714x_wheel_cal_highest_stage(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_wheel_plat *hw = &ad714x->hw->wheel[idx]; + struct ad714x_wheel_drv *sw = &ad714x->sw->wheel[idx]; + + sw->pre_highest_stage = sw->highest_stage; + sw->highest_stage = ad714x_cal_highest_stage(ad714x, hw->start_stage, + hw->end_stage); + + dev_dbg(ad714x->dev, "wheel %d highest_stage:%d\n", idx, + sw->highest_stage); +} + +static void ad714x_wheel_cal_sensor_val(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_wheel_plat *hw = &ad714x->hw->wheel[idx]; + int i; + + for (i = hw->start_stage; i <= hw->end_stage; i++) { + ad714x->read(ad714x->dev, CDC_RESULT_S0 + i, + &ad714x->adc_reg[i]); + ad714x->read(ad714x->dev, + STAGE0_AMBIENT + i * PER_STAGE_REG_NUM, + &ad714x->amb_reg[i]); + if (ad714x->adc_reg[i] > ad714x->amb_reg[i]) + ad714x->sensor_val[i] = ad714x->adc_reg[i] - + ad714x->amb_reg[i]; + else + ad714x->sensor_val[i] = 0; + } +} + +/* + * When the scroll wheel is activated, we compute the absolute position based + * on the sensor values. To calculate the position, we first determine the + * sensor that has the greatest response among the 8 sensors that constitutes + * the scrollwheel. Then we determined the 2 sensors on either sides of the + * sensor with the highest response and we apply weights to these sensors. The + * result of this computation gives us the mean value which defined by the + * following formula: + * For i= second_before_highest_stage to i= second_after_highest_stage + * v += Sensor response(i)*WEIGHT*(i+3) + * w += Sensor response(i) + * Mean_Value=v/w + * pos_on_scrollwheel = (Mean_Value - position_offset) / position_ratio + */ + +#define WEIGHT_FACTOR 30 +/* This constant prevents the "PositionOffset" from reaching a big value */ +#define OFFSET_POSITION_CLAMP 120 +static void ad714x_wheel_cal_abs_pos(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_wheel_plat *hw = &ad714x->hw->wheel[idx]; + struct ad714x_wheel_drv *sw = &ad714x->sw->wheel[idx]; + int stage_num = hw->end_stage - hw->start_stage + 1; + int second_before, first_before, highest, first_after, second_after; + int a_param, b_param; + + /* Calculate Mean value */ + + second_before = (sw->highest_stage + stage_num - 2) % stage_num; + first_before = (sw->highest_stage + stage_num - 1) % stage_num; + highest = sw->highest_stage; + first_after = (sw->highest_stage + stage_num + 1) % stage_num; + second_after = (sw->highest_stage + stage_num + 2) % stage_num; + + if (((sw->highest_stage - hw->start_stage) > 1) && + ((hw->end_stage - sw->highest_stage) > 1)) { + a_param = ad714x->sensor_val[second_before] * + (second_before - hw->start_stage + 3) + + ad714x->sensor_val[first_before] * + (second_before - hw->start_stage + 3) + + ad714x->sensor_val[highest] * + (second_before - hw->start_stage + 3) + + ad714x->sensor_val[first_after] * + (first_after - hw->start_stage + 3) + + ad714x->sensor_val[second_after] * + (second_after - hw->start_stage + 3); + } else { + a_param = ad714x->sensor_val[second_before] * + (second_before - hw->start_stage + 1) + + ad714x->sensor_val[first_before] * + (second_before - hw->start_stage + 2) + + ad714x->sensor_val[highest] * + (second_before - hw->start_stage + 3) + + ad714x->sensor_val[first_after] * + (first_after - hw->start_stage + 4) + + ad714x->sensor_val[second_after] * + (second_after - hw->start_stage + 5); + } + a_param *= WEIGHT_FACTOR; + + b_param = ad714x->sensor_val[second_before] + + ad714x->sensor_val[first_before] + + ad714x->sensor_val[highest] + + ad714x->sensor_val[first_after] + + ad714x->sensor_val[second_after]; + + sw->pre_mean_value = sw->mean_value; + sw->mean_value = a_param / b_param; + + /* Calculate the offset */ + + if ((sw->pre_highest_stage == hw->end_stage) && + (sw->highest_stage == hw->start_stage)) + sw->pos_offset = sw->mean_value; + else if ((sw->pre_highest_stage == hw->start_stage) && + (sw->highest_stage == hw->end_stage)) + sw->pos_offset = sw->pre_mean_value; + + if (sw->pos_offset > OFFSET_POSITION_CLAMP) + sw->pos_offset = OFFSET_POSITION_CLAMP; + + /* Calculate the mean value without the offset */ + + sw->pre_mean_value_no_offset = sw->mean_value_no_offset; + sw->mean_value_no_offset = sw->mean_value - sw->pos_offset; + if (sw->mean_value_no_offset < 0) + sw->mean_value_no_offset = 0; + + /* Calculate ratio to scale down to NUMBER_OF_WANTED_POSITIONS */ + + if ((sw->pre_highest_stage == hw->end_stage) && + (sw->highest_stage == hw->start_stage)) + sw->pos_ratio = (sw->pre_mean_value_no_offset * 100) / + hw->max_coord; + else if ((sw->pre_highest_stage == hw->start_stage) && + (sw->highest_stage == hw->end_stage)) + sw->pos_ratio = (sw->mean_value_no_offset * 100) / + hw->max_coord; + sw->abs_pos = (sw->mean_value_no_offset * 100) / sw->pos_ratio; + if (sw->abs_pos > hw->max_coord) + sw->abs_pos = hw->max_coord; +} + +static void ad714x_wheel_cal_flt_pos(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_wheel_plat *hw = &ad714x->hw->wheel[idx]; + struct ad714x_wheel_drv *sw = &ad714x->sw->wheel[idx]; + if (((sw->pre_highest_stage == hw->end_stage) && + (sw->highest_stage == hw->start_stage)) || + ((sw->pre_highest_stage == hw->start_stage) && + (sw->highest_stage == hw->end_stage))) + sw->flt_pos = sw->abs_pos; + else + sw->flt_pos = ((sw->flt_pos * 30) + (sw->abs_pos * 71)) / 100; + + if (sw->flt_pos > hw->max_coord) + sw->flt_pos = hw->max_coord; +} + +static void ad714x_wheel_use_com_int(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_wheel_plat *hw = &ad714x->hw->wheel[idx]; + + ad714x_use_com_int(ad714x, hw->start_stage, hw->end_stage); +} + +static void ad714x_wheel_use_thr_int(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_wheel_plat *hw = &ad714x->hw->wheel[idx]; + + ad714x_use_thr_int(ad714x, hw->start_stage, hw->end_stage); +} + +static void ad714x_wheel_state_machine(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_wheel_plat *hw = &ad714x->hw->wheel[idx]; + struct ad714x_wheel_drv *sw = &ad714x->sw->wheel[idx]; + unsigned short h_state, c_state; + unsigned short mask; + + mask = ((1 << (hw->end_stage + 1)) - 1) - ((1 << hw->start_stage) - 1); + + h_state = ad714x->h_state & mask; + c_state = ad714x->c_state & mask; + + switch (sw->state) { + case IDLE: + if (h_state) { + sw->state = JITTER; + /* In End of Conversion interrupt mode, the AD714X + * continuously generates hardware interrupts. + */ + ad714x_wheel_use_com_int(ad714x, idx); + dev_dbg(ad714x->dev, "wheel %d touched\n", idx); + } + break; + + case JITTER: + if (c_state == mask) { + ad714x_wheel_cal_sensor_val(ad714x, idx); + ad714x_wheel_cal_highest_stage(ad714x, idx); + ad714x_wheel_cal_abs_pos(ad714x, idx); + sw->flt_pos = sw->abs_pos; + sw->state = ACTIVE; + } + break; + + case ACTIVE: + if (c_state == mask) { + if (h_state) { + ad714x_wheel_cal_sensor_val(ad714x, idx); + ad714x_wheel_cal_highest_stage(ad714x, idx); + ad714x_wheel_cal_abs_pos(ad714x, idx); + ad714x_wheel_cal_flt_pos(ad714x, idx); + + input_report_abs(sw->input, ABS_WHEEL, + sw->abs_pos); + input_report_key(sw->input, BTN_TOUCH, 1); + } else { + /* When the user lifts off the sensor, configure + * the AD714X back to threshold interrupt mode. + */ + ad714x_wheel_use_thr_int(ad714x, idx); + sw->state = IDLE; + input_report_key(sw->input, BTN_TOUCH, 0); + + dev_dbg(ad714x->dev, "wheel %d released\n", + idx); + } + input_sync(sw->input); + } + break; + + default: + break; + } +} + +static void touchpad_cal_sensor_val(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_touchpad_plat *hw = &ad714x->hw->touchpad[idx]; + int i; + + for (i = hw->x_start_stage; i <= hw->x_end_stage; i++) { + ad714x->read(ad714x->dev, CDC_RESULT_S0 + i, + &ad714x->adc_reg[i]); + ad714x->read(ad714x->dev, + STAGE0_AMBIENT + i * PER_STAGE_REG_NUM, + &ad714x->amb_reg[i]); + if (ad714x->adc_reg[i] > ad714x->amb_reg[i]) + ad714x->sensor_val[i] = ad714x->adc_reg[i] - + ad714x->amb_reg[i]; + else + ad714x->sensor_val[i] = 0; + } +} + +static void touchpad_cal_highest_stage(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_touchpad_plat *hw = &ad714x->hw->touchpad[idx]; + struct ad714x_touchpad_drv *sw = &ad714x->sw->touchpad[idx]; + + sw->x_highest_stage = ad714x_cal_highest_stage(ad714x, + hw->x_start_stage, hw->x_end_stage); + sw->y_highest_stage = ad714x_cal_highest_stage(ad714x, + hw->y_start_stage, hw->y_end_stage); + + dev_dbg(ad714x->dev, + "touchpad %d x_highest_stage:%d, y_highest_stage:%d\n", + idx, sw->x_highest_stage, sw->y_highest_stage); +} + +/* + * If 2 fingers are touching the sensor then 2 peaks can be observed in the + * distribution. + * The arithmetic doesn't support to get absolute coordinates for multi-touch + * yet. + */ +static int touchpad_check_second_peak(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_touchpad_plat *hw = &ad714x->hw->touchpad[idx]; + struct ad714x_touchpad_drv *sw = &ad714x->sw->touchpad[idx]; + int i; + + for (i = hw->x_start_stage; i < sw->x_highest_stage; i++) { + if ((ad714x->sensor_val[i] - ad714x->sensor_val[i + 1]) + > (ad714x->sensor_val[i + 1] / 10)) + return 1; + } + + for (i = sw->x_highest_stage; i < hw->x_end_stage; i++) { + if ((ad714x->sensor_val[i + 1] - ad714x->sensor_val[i]) + > (ad714x->sensor_val[i] / 10)) + return 1; + } + + for (i = hw->y_start_stage; i < sw->y_highest_stage; i++) { + if ((ad714x->sensor_val[i] - ad714x->sensor_val[i + 1]) + > (ad714x->sensor_val[i + 1] / 10)) + return 1; + } + + for (i = sw->y_highest_stage; i < hw->y_end_stage; i++) { + if ((ad714x->sensor_val[i + 1] - ad714x->sensor_val[i]) + > (ad714x->sensor_val[i] / 10)) + return 1; + } + + return 0; +} + +/* + * If only one finger is used to activate the touch pad then only 1 peak will be + * registered in the distribution. This peak and the 2 adjacent sensors will be + * used in the calculation of the absolute position. This will prevent hand + * shadows to affect the absolute position calculation. + */ +static void touchpad_cal_abs_pos(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_touchpad_plat *hw = &ad714x->hw->touchpad[idx]; + struct ad714x_touchpad_drv *sw = &ad714x->sw->touchpad[idx]; + + sw->x_abs_pos = ad714x_cal_abs_pos(ad714x, hw->x_start_stage, + hw->x_end_stage, sw->x_highest_stage, hw->x_max_coord); + sw->y_abs_pos = ad714x_cal_abs_pos(ad714x, hw->y_start_stage, + hw->y_end_stage, sw->y_highest_stage, hw->y_max_coord); + + dev_dbg(ad714x->dev, "touchpad %d absolute position:(%d, %d)\n", idx, + sw->x_abs_pos, sw->y_abs_pos); +} + +static void touchpad_cal_flt_pos(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_touchpad_drv *sw = &ad714x->sw->touchpad[idx]; + + sw->x_flt_pos = (sw->x_flt_pos * (10 - 4) + + sw->x_abs_pos * 4)/10; + sw->y_flt_pos = (sw->y_flt_pos * (10 - 4) + + sw->y_abs_pos * 4)/10; + + dev_dbg(ad714x->dev, "touchpad %d filter position:(%d, %d)\n", + idx, sw->x_flt_pos, sw->y_flt_pos); +} + +/* + * To prevent distortion from showing in the absolute position, it is + * necessary to detect the end points. When endpoints are detected, the + * driver stops updating the status variables with absolute positions. + * End points are detected on the 4 edges of the touchpad sensor. The + * method to detect them is the same for all 4. + * To detect the end points, the firmware computes the difference in + * percent between the sensor on the edge and the adjacent one. The + * difference is calculated in percent in order to make the end point + * detection independent of the pressure. + */ + +#define LEFT_END_POINT_DETECTION_LEVEL 550 +#define RIGHT_END_POINT_DETECTION_LEVEL 750 +#define LEFT_RIGHT_END_POINT_DEAVTIVALION_LEVEL 850 +#define TOP_END_POINT_DETECTION_LEVEL 550 +#define BOTTOM_END_POINT_DETECTION_LEVEL 950 +#define TOP_BOTTOM_END_POINT_DEAVTIVALION_LEVEL 700 +static int touchpad_check_endpoint(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_touchpad_plat *hw = &ad714x->hw->touchpad[idx]; + struct ad714x_touchpad_drv *sw = &ad714x->sw->touchpad[idx]; + int percent_sensor_diff; + + /* left endpoint detect */ + percent_sensor_diff = (ad714x->sensor_val[hw->x_start_stage] - + ad714x->sensor_val[hw->x_start_stage + 1]) * 100 / + ad714x->sensor_val[hw->x_start_stage + 1]; + if (!sw->left_ep) { + if (percent_sensor_diff >= LEFT_END_POINT_DETECTION_LEVEL) { + sw->left_ep = 1; + sw->left_ep_val = + ad714x->sensor_val[hw->x_start_stage + 1]; + } + } else { + if ((percent_sensor_diff < LEFT_END_POINT_DETECTION_LEVEL) && + (ad714x->sensor_val[hw->x_start_stage + 1] > + LEFT_RIGHT_END_POINT_DEAVTIVALION_LEVEL + sw->left_ep_val)) + sw->left_ep = 0; + } + + /* right endpoint detect */ + percent_sensor_diff = (ad714x->sensor_val[hw->x_end_stage] - + ad714x->sensor_val[hw->x_end_stage - 1]) * 100 / + ad714x->sensor_val[hw->x_end_stage - 1]; + if (!sw->right_ep) { + if (percent_sensor_diff >= RIGHT_END_POINT_DETECTION_LEVEL) { + sw->right_ep = 1; + sw->right_ep_val = + ad714x->sensor_val[hw->x_end_stage - 1]; + } + } else { + if ((percent_sensor_diff < RIGHT_END_POINT_DETECTION_LEVEL) && + (ad714x->sensor_val[hw->x_end_stage - 1] > + LEFT_RIGHT_END_POINT_DEAVTIVALION_LEVEL + sw->right_ep_val)) + sw->right_ep = 0; + } + + /* top endpoint detect */ + percent_sensor_diff = (ad714x->sensor_val[hw->y_start_stage] - + ad714x->sensor_val[hw->y_start_stage + 1]) * 100 / + ad714x->sensor_val[hw->y_start_stage + 1]; + if (!sw->top_ep) { + if (percent_sensor_diff >= TOP_END_POINT_DETECTION_LEVEL) { + sw->top_ep = 1; + sw->top_ep_val = + ad714x->sensor_val[hw->y_start_stage + 1]; + } + } else { + if ((percent_sensor_diff < TOP_END_POINT_DETECTION_LEVEL) && + (ad714x->sensor_val[hw->y_start_stage + 1] > + TOP_BOTTOM_END_POINT_DEAVTIVALION_LEVEL + sw->top_ep_val)) + sw->top_ep = 0; + } + + /* bottom endpoint detect */ + percent_sensor_diff = (ad714x->sensor_val[hw->y_end_stage] - + ad714x->sensor_val[hw->y_end_stage - 1]) * 100 / + ad714x->sensor_val[hw->y_end_stage - 1]; + if (!sw->bottom_ep) { + if (percent_sensor_diff >= BOTTOM_END_POINT_DETECTION_LEVEL) { + sw->bottom_ep = 1; + sw->bottom_ep_val = + ad714x->sensor_val[hw->y_end_stage - 1]; + } + } else { + if ((percent_sensor_diff < BOTTOM_END_POINT_DETECTION_LEVEL) && + (ad714x->sensor_val[hw->y_end_stage - 1] > + TOP_BOTTOM_END_POINT_DEAVTIVALION_LEVEL + sw->bottom_ep_val)) + sw->bottom_ep = 0; + } + + return sw->left_ep || sw->right_ep || sw->top_ep || sw->bottom_ep; +} + +static void touchpad_use_com_int(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_touchpad_plat *hw = &ad714x->hw->touchpad[idx]; + + ad714x_use_com_int(ad714x, hw->x_start_stage, hw->x_end_stage); +} + +static void touchpad_use_thr_int(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_touchpad_plat *hw = &ad714x->hw->touchpad[idx]; + + ad714x_use_thr_int(ad714x, hw->x_start_stage, hw->x_end_stage); + ad714x_use_thr_int(ad714x, hw->y_start_stage, hw->y_end_stage); +} + +static void ad714x_touchpad_state_machine(struct ad714x_chip *ad714x, int idx) +{ + struct ad714x_touchpad_plat *hw = &ad714x->hw->touchpad[idx]; + struct ad714x_touchpad_drv *sw = &ad714x->sw->touchpad[idx]; + unsigned short h_state, c_state; + unsigned short mask; + + mask = (((1 << (hw->x_end_stage + 1)) - 1) - + ((1 << hw->x_start_stage) - 1)) + + (((1 << (hw->y_end_stage + 1)) - 1) - + ((1 << hw->y_start_stage) - 1)); + + h_state = ad714x->h_state & mask; + c_state = ad714x->c_state & mask; + + switch (sw->state) { + case IDLE: + if (h_state) { + sw->state = JITTER; + /* In End of Conversion interrupt mode, the AD714X + * continuously generates hardware interrupts. + */ + touchpad_use_com_int(ad714x, idx); + dev_dbg(ad714x->dev, "touchpad %d touched\n", idx); + } + break; + + case JITTER: + if (c_state == mask) { + touchpad_cal_sensor_val(ad714x, idx); + touchpad_cal_highest_stage(ad714x, idx); + if ((!touchpad_check_second_peak(ad714x, idx)) && + (!touchpad_check_endpoint(ad714x, idx))) { + dev_dbg(ad714x->dev, + "touchpad%d, 2 fingers or endpoint\n", + idx); + touchpad_cal_abs_pos(ad714x, idx); + sw->x_flt_pos = sw->x_abs_pos; + sw->y_flt_pos = sw->y_abs_pos; + sw->state = ACTIVE; + } + } + break; + + case ACTIVE: + if (c_state == mask) { + if (h_state) { + touchpad_cal_sensor_val(ad714x, idx); + touchpad_cal_highest_stage(ad714x, idx); + if ((!touchpad_check_second_peak(ad714x, idx)) + && (!touchpad_check_endpoint(ad714x, idx))) { + touchpad_cal_abs_pos(ad714x, idx); + touchpad_cal_flt_pos(ad714x, idx); + input_report_abs(sw->input, ABS_X, + sw->x_flt_pos); + input_report_abs(sw->input, ABS_Y, + sw->y_flt_pos); + input_report_key(sw->input, BTN_TOUCH, + 1); + } + } else { + /* When the user lifts off the sensor, configure + * the AD714X back to threshold interrupt mode. + */ + touchpad_use_thr_int(ad714x, idx); + sw->state = IDLE; + input_report_key(sw->input, BTN_TOUCH, 0); + dev_dbg(ad714x->dev, "touchpad %d released\n", + idx); + } + input_sync(sw->input); + } + break; + + default: + break; + } +} + +static int ad714x_hw_detect(struct ad714x_chip *ad714x) +{ + unsigned short data; + + ad714x->read(ad714x->dev, AD714X_PARTID_REG, &data); + switch (data & 0xFFF0) { + case AD7142_PARTID: + ad714x->product = 0x7142; + ad714x->version = data & 0xF; + dev_info(ad714x->dev, "found AD7142 captouch, rev:%d\n", + ad714x->version); + return 0; + + case AD7143_PARTID: + ad714x->product = 0x7143; + ad714x->version = data & 0xF; + dev_info(ad714x->dev, "found AD7143 captouch, rev:%d\n", + ad714x->version); + return 0; + + case AD7147_PARTID: + ad714x->product = 0x7147; + ad714x->version = data & 0xF; + dev_info(ad714x->dev, "found AD7147(A) captouch, rev:%d\n", + ad714x->version); + return 0; + + case AD7148_PARTID: + ad714x->product = 0x7148; + ad714x->version = data & 0xF; + dev_info(ad714x->dev, "found AD7148 captouch, rev:%d\n", + ad714x->version); + return 0; + + default: + dev_err(ad714x->dev, + "fail to detect AD714X captouch, read ID is %04x\n", + data); + return -ENODEV; + } +} + +static void ad714x_hw_init(struct ad714x_chip *ad714x) +{ + int i, j; + unsigned short reg_base; + unsigned short data; + + /* configuration CDC and interrupts */ + + for (i = 0; i < STAGE_NUM; i++) { + reg_base = AD714X_STAGECFG_REG + i * STAGE_CFGREG_NUM; + for (j = 0; j < STAGE_CFGREG_NUM; j++) + ad714x->write(ad714x->dev, reg_base + j, + ad714x->hw->stage_cfg_reg[i][j]); + } + + for (i = 0; i < SYS_CFGREG_NUM; i++) + ad714x->write(ad714x->dev, AD714X_SYSCFG_REG + i, + ad714x->hw->sys_cfg_reg[i]); + for (i = 0; i < SYS_CFGREG_NUM; i++) + ad714x->read(ad714x->dev, AD714X_SYSCFG_REG + i, + &data); + + ad714x->write(ad714x->dev, AD714X_STG_CAL_EN_REG, 0xFFF); + + /* clear all interrupts */ + ad714x->read(ad714x->dev, STG_LOW_INT_STA_REG, &data); + ad714x->read(ad714x->dev, STG_HIGH_INT_STA_REG, &data); + ad714x->read(ad714x->dev, STG_COM_INT_STA_REG, &data); +} + +static irqreturn_t ad714x_interrupt_thread(int irq, void *data) +{ + struct ad714x_chip *ad714x = data; + int i; + + mutex_lock(&ad714x->mutex); + + ad714x->read(ad714x->dev, STG_LOW_INT_STA_REG, &ad714x->l_state); + ad714x->read(ad714x->dev, STG_HIGH_INT_STA_REG, &ad714x->h_state); + ad714x->read(ad714x->dev, STG_COM_INT_STA_REG, &ad714x->c_state); + + for (i = 0; i < ad714x->hw->button_num; i++) + ad714x_button_state_machine(ad714x, i); + for (i = 0; i < ad714x->hw->slider_num; i++) + ad714x_slider_state_machine(ad714x, i); + for (i = 0; i < ad714x->hw->wheel_num; i++) + ad714x_wheel_state_machine(ad714x, i); + for (i = 0; i < ad714x->hw->touchpad_num; i++) + ad714x_touchpad_state_machine(ad714x, i); + + mutex_unlock(&ad714x->mutex); + + return IRQ_HANDLED; +} + +#define MAX_DEVICE_NUM 8 +struct ad714x_chip *ad714x_probe(struct device *dev, u16 bus_type, int irq, + ad714x_read_t read, ad714x_write_t write) +{ + int i, alloc_idx; + int error; + struct input_dev *input[MAX_DEVICE_NUM]; + + struct ad714x_platform_data *plat_data = dev->platform_data; + struct ad714x_chip *ad714x; + void *drv_mem; + + struct ad714x_button_drv *bt_drv; + struct ad714x_slider_drv *sd_drv; + struct ad714x_wheel_drv *wl_drv; + struct ad714x_touchpad_drv *tp_drv; + + + if (irq <= 0) { + dev_err(dev, "IRQ not configured!\n"); + error = -EINVAL; + goto err_out; + } + + if (dev->platform_data == NULL) { + dev_err(dev, "platform data for ad714x doesn't exist\n"); + error = -EINVAL; + goto err_out; + } + + ad714x = kzalloc(sizeof(*ad714x) + sizeof(*ad714x->sw) + + sizeof(*sd_drv) * plat_data->slider_num + + sizeof(*wl_drv) * plat_data->wheel_num + + sizeof(*tp_drv) * plat_data->touchpad_num + + sizeof(*bt_drv) * plat_data->button_num, GFP_KERNEL); + if (!ad714x) { + error = -ENOMEM; + goto err_out; + } + + ad714x->hw = plat_data; + + drv_mem = ad714x + 1; + ad714x->sw = drv_mem; + drv_mem += sizeof(*ad714x->sw); + ad714x->sw->slider = sd_drv = drv_mem; + drv_mem += sizeof(*sd_drv) * ad714x->hw->slider_num; + ad714x->sw->wheel = wl_drv = drv_mem; + drv_mem += sizeof(*wl_drv) * ad714x->hw->wheel_num; + ad714x->sw->touchpad = tp_drv = drv_mem; + drv_mem += sizeof(*tp_drv) * ad714x->hw->touchpad_num; + ad714x->sw->button = bt_drv = drv_mem; + drv_mem += sizeof(*bt_drv) * ad714x->hw->button_num; + + ad714x->read = read; + ad714x->write = write; + ad714x->irq = irq; + ad714x->dev = dev; + + error = ad714x_hw_detect(ad714x); + if (error) + goto err_free_mem; + + /* initilize and request sw/hw resources */ + + ad714x_hw_init(ad714x); + mutex_init(&ad714x->mutex); + + /* + * Allocate and register AD714X input device + */ + alloc_idx = 0; + + /* a slider uses one input_dev instance */ + if (ad714x->hw->slider_num > 0) { + struct ad714x_slider_plat *sd_plat = ad714x->hw->slider; + + for (i = 0; i < ad714x->hw->slider_num; i++) { + sd_drv[i].input = input[alloc_idx] = input_allocate_device(); + if (!input[alloc_idx]) { + error = -ENOMEM; + goto err_free_dev; + } + + __set_bit(EV_ABS, input[alloc_idx]->evbit); + __set_bit(EV_KEY, input[alloc_idx]->evbit); + __set_bit(ABS_X, input[alloc_idx]->absbit); + __set_bit(BTN_TOUCH, input[alloc_idx]->keybit); + input_set_abs_params(input[alloc_idx], + ABS_X, 0, sd_plat->max_coord, 0, 0); + + input[alloc_idx]->id.bustype = bus_type; + input[alloc_idx]->id.product = ad714x->product; + input[alloc_idx]->id.version = ad714x->version; + + error = input_register_device(input[alloc_idx]); + if (error) + goto err_free_dev; + + alloc_idx++; + } + } + + /* a wheel uses one input_dev instance */ + if (ad714x->hw->wheel_num > 0) { + struct ad714x_wheel_plat *wl_plat = ad714x->hw->wheel; + + for (i = 0; i < ad714x->hw->wheel_num; i++) { + wl_drv[i].input = input[alloc_idx] = input_allocate_device(); + if (!input[alloc_idx]) { + error = -ENOMEM; + goto err_free_dev; + } + + __set_bit(EV_KEY, input[alloc_idx]->evbit); + __set_bit(EV_ABS, input[alloc_idx]->evbit); + __set_bit(ABS_WHEEL, input[alloc_idx]->absbit); + __set_bit(BTN_TOUCH, input[alloc_idx]->keybit); + input_set_abs_params(input[alloc_idx], + ABS_WHEEL, 0, wl_plat->max_coord, 0, 0); + + input[alloc_idx]->id.bustype = bus_type; + input[alloc_idx]->id.product = ad714x->product; + input[alloc_idx]->id.version = ad714x->version; + + error = input_register_device(input[alloc_idx]); + if (error) + goto err_free_dev; + + alloc_idx++; + } + } + + /* a touchpad uses one input_dev instance */ + if (ad714x->hw->touchpad_num > 0) { + struct ad714x_touchpad_plat *tp_plat = ad714x->hw->touchpad; + + for (i = 0; i < ad714x->hw->touchpad_num; i++) { + tp_drv[i].input = input[alloc_idx] = input_allocate_device(); + if (!input[alloc_idx]) { + error = -ENOMEM; + goto err_free_dev; + } + + __set_bit(EV_ABS, input[alloc_idx]->evbit); + __set_bit(EV_KEY, input[alloc_idx]->evbit); + __set_bit(ABS_X, input[alloc_idx]->absbit); + __set_bit(ABS_Y, input[alloc_idx]->absbit); + __set_bit(BTN_TOUCH, input[alloc_idx]->keybit); + input_set_abs_params(input[alloc_idx], + ABS_X, 0, tp_plat->x_max_coord, 0, 0); + input_set_abs_params(input[alloc_idx], + ABS_Y, 0, tp_plat->y_max_coord, 0, 0); + + input[alloc_idx]->id.bustype = bus_type; + input[alloc_idx]->id.product = ad714x->product; + input[alloc_idx]->id.version = ad714x->version; + + error = input_register_device(input[alloc_idx]); + if (error) + goto err_free_dev; + + alloc_idx++; + } + } + + /* all buttons use one input node */ + if (ad714x->hw->button_num > 0) { + struct ad714x_button_plat *bt_plat = ad714x->hw->button; + + input[alloc_idx] = input_allocate_device(); + if (!input[alloc_idx]) { + error = -ENOMEM; + goto err_free_dev; + } + + __set_bit(EV_KEY, input[alloc_idx]->evbit); + for (i = 0; i < ad714x->hw->button_num; i++) { + bt_drv[i].input = input[alloc_idx]; + __set_bit(bt_plat[i].keycode, input[alloc_idx]->keybit); + } + + input[alloc_idx]->id.bustype = bus_type; + input[alloc_idx]->id.product = ad714x->product; + input[alloc_idx]->id.version = ad714x->version; + + error = input_register_device(input[alloc_idx]); + if (error) + goto err_free_dev; + + alloc_idx++; + } + + error = request_threaded_irq(ad714x->irq, NULL, ad714x_interrupt_thread, + IRQF_TRIGGER_FALLING, "ad714x_captouch", ad714x); + if (error) { + dev_err(dev, "can't allocate irq %d\n", ad714x->irq); + goto err_unreg_dev; + } + + return ad714x; + + err_free_dev: + dev_err(dev, "failed to setup AD714x input device %i\n", alloc_idx); + input_free_device(input[alloc_idx]); + err_unreg_dev: + while (--alloc_idx >= 0) + input_unregister_device(input[alloc_idx]); + err_free_mem: + kfree(ad714x); + err_out: + return ERR_PTR(error); +} +EXPORT_SYMBOL(ad714x_probe); + +void ad714x_remove(struct ad714x_chip *ad714x) +{ + struct ad714x_platform_data *hw = ad714x->hw; + struct ad714x_driver_data *sw = ad714x->sw; + int i; + + free_irq(ad714x->irq, ad714x); + + /* unregister and free all input devices */ + + for (i = 0; i < hw->slider_num; i++) + input_unregister_device(sw->slider[i].input); + + for (i = 0; i < hw->wheel_num; i++) + input_unregister_device(sw->wheel[i].input); + + for (i = 0; i < hw->touchpad_num; i++) + input_unregister_device(sw->touchpad[i].input); + + if (hw->button_num) + input_unregister_device(sw->button[0].input); + + kfree(ad714x); +} +EXPORT_SYMBOL(ad714x_remove); + +#ifdef CONFIG_PM +int ad714x_disable(struct ad714x_chip *ad714x) +{ + unsigned short data; + + dev_dbg(ad714x->dev, "%s enter\n", __func__); + + mutex_lock(&ad714x->mutex); + + data = ad714x->hw->sys_cfg_reg[AD714X_PWR_CTRL] | 0x3; + ad714x->write(ad714x->dev, AD714X_PWR_CTRL, data); + + mutex_unlock(&ad714x->mutex); + + return 0; +} +EXPORT_SYMBOL(ad714x_disable); + +int ad714x_enable(struct ad714x_chip *ad714x) +{ + unsigned short data; + + dev_dbg(ad714x->dev, "%s enter\n", __func__); + + mutex_lock(&ad714x->mutex); + + /* resume to non-shutdown mode */ + + ad714x->write(ad714x->dev, AD714X_PWR_CTRL, + ad714x->hw->sys_cfg_reg[AD714X_PWR_CTRL]); + + /* make sure the interrupt output line is not low level after resume, + * otherwise we will get no chance to enter falling-edge irq again + */ + + ad714x->read(ad714x->dev, STG_LOW_INT_STA_REG, &data); + ad714x->read(ad714x->dev, STG_HIGH_INT_STA_REG, &data); + ad714x->read(ad714x->dev, STG_COM_INT_STA_REG, &data); + + mutex_unlock(&ad714x->mutex); + + return 0; +} +EXPORT_SYMBOL(ad714x_enable); +#endif + +MODULE_DESCRIPTION("Analog Devices AD714X Capacitance Touch Sensor Driver"); +MODULE_AUTHOR("Barry Song <21cnbao@gmail.com>"); +MODULE_LICENSE("GPL"); diff --git a/drivers/input/misc/ad714x.h b/drivers/input/misc/ad714x.h new file mode 100644 index 000000000000..45c54fb13f07 --- /dev/null +++ b/drivers/input/misc/ad714x.h @@ -0,0 +1,26 @@ +/* + * AD714X CapTouch Programmable Controller driver (bus interfaces) + * + * Copyright 2009 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#ifndef _AD714X_H_ +#define _AD714X_H_ + +#include <linux/types.h> + +struct device; +struct ad714x_chip; + +typedef int (*ad714x_read_t)(struct device *, unsigned short, unsigned short *); +typedef int (*ad714x_write_t)(struct device *, unsigned short, unsigned short); + +int ad714x_disable(struct ad714x_chip *ad714x); +int ad714x_enable(struct ad714x_chip *ad714x); +struct ad714x_chip *ad714x_probe(struct device *dev, u16 bus_type, int irq, + ad714x_read_t read, ad714x_write_t write); +void ad714x_remove(struct ad714x_chip *ad714x); + +#endif diff --git a/drivers/input/misc/pcf8574_keypad.c b/drivers/input/misc/pcf8574_keypad.c new file mode 100644 index 000000000000..5c3ac4e0b055 --- /dev/null +++ b/drivers/input/misc/pcf8574_keypad.c @@ -0,0 +1,227 @@ +/* + * Driver for a keypad w/16 buttons connected to a PCF8574 I2C I/O expander + * + * Copyright 2005-2008 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/input.h> +#include <linux/interrupt.h> +#include <linux/i2c.h> +#include <linux/slab.h> +#include <linux/workqueue.h> + +#define DRV_NAME "pcf8574_keypad" + +static const unsigned char pcf8574_kp_btncode[] = { + [0] = KEY_RESERVED, + [1] = KEY_ENTER, + [2] = KEY_BACKSLASH, + [3] = KEY_0, + [4] = KEY_RIGHTBRACE, + [5] = KEY_C, + [6] = KEY_9, + [7] = KEY_8, + [8] = KEY_7, + [9] = KEY_B, + [10] = KEY_6, + [11] = KEY_5, + [12] = KEY_4, + [13] = KEY_A, + [14] = KEY_3, + [15] = KEY_2, + [16] = KEY_1 +}; + +struct kp_data { + unsigned short btncode[ARRAY_SIZE(pcf8574_kp_btncode)]; + struct input_dev *idev; + struct i2c_client *client; + char name[64]; + char phys[32]; + unsigned char laststate; +}; + +static short read_state(struct kp_data *lp) +{ + unsigned char x, y, a, b; + + i2c_smbus_write_byte(lp->client, 240); + x = 0xF & (~(i2c_smbus_read_byte(lp->client) >> 4)); + + i2c_smbus_write_byte(lp->client, 15); + y = 0xF & (~i2c_smbus_read_byte(lp->client)); + + for (a = 0; x > 0; a++) + x = x >> 1; + for (b = 0; y > 0; b++) + y = y >> 1; + + return ((a - 1) * 4) + b; +} + +static irqreturn_t pcf8574_kp_irq_handler(int irq, void *dev_id) +{ + struct kp_data *lp = dev_id; + unsigned char nextstate = read_state(lp); + + if (lp->laststate != nextstate) { + int key_down = nextstate <= ARRAY_SIZE(lp->btncode); + unsigned short keycode = key_down ? + lp->btncode[nextstate] : lp->btncode[lp->laststate]; + + input_report_key(lp->idev, keycode, key_down); + input_sync(lp->idev); + + lp->laststate = nextstate; + } + + return IRQ_HANDLED; +} + +static int __devinit pcf8574_kp_probe(struct i2c_client *client, const struct i2c_device_id *id) +{ + int i, ret; + struct input_dev *idev; + struct kp_data *lp; + + if (i2c_smbus_write_byte(client, 240) < 0) { + dev_err(&client->dev, "probe: write fail\n"); + return -ENODEV; + } + + lp = kzalloc(sizeof(*lp), GFP_KERNEL); + if (!lp) + return -ENOMEM; + + idev = input_allocate_device(); + if (!idev) { + dev_err(&client->dev, "Can't allocate input device\n"); + ret = -ENOMEM; + goto fail_allocate; + } + + lp->idev = idev; + lp->client = client; + + idev->evbit[0] = BIT_MASK(EV_KEY); + idev->keycode = lp->btncode; + idev->keycodesize = sizeof(lp->btncode[0]); + idev->keycodemax = ARRAY_SIZE(lp->btncode); + + for (i = 0; i < ARRAY_SIZE(pcf8574_kp_btncode); i++) { + lp->btncode[i] = pcf8574_kp_btncode[i]; + __set_bit(lp->btncode[i] & KEY_MAX, idev->keybit); + } + + sprintf(lp->name, DRV_NAME); + sprintf(lp->phys, "kp_data/input0"); + + idev->name = lp->name; + idev->phys = lp->phys; + idev->id.bustype = BUS_I2C; + idev->id.vendor = 0x0001; + idev->id.product = 0x0001; + idev->id.version = 0x0100; + + input_set_drvdata(idev, lp); + + ret = input_register_device(idev); + if (ret) { + dev_err(&client->dev, "input_register_device() failed\n"); + goto fail_register; + } + + lp->laststate = read_state(lp); + + ret = request_threaded_irq(client->irq, NULL, pcf8574_kp_irq_handler, + IRQF_TRIGGER_LOW | IRQF_ONESHOT, + DRV_NAME, lp); + if (ret) { + dev_err(&client->dev, "IRQ %d is not free\n", client->irq); + goto fail_irq; + } + + i2c_set_clientdata(client, lp); + return 0; + + fail_irq: + input_unregister_device(idev); + fail_register: + input_set_drvdata(idev, NULL); + input_free_device(idev); + fail_allocate: + kfree(lp); + + return ret; +} + +static int __devexit pcf8574_kp_remove(struct i2c_client *client) +{ + struct kp_data *lp = i2c_get_clientdata(client); + + free_irq(client->irq, lp); + + input_unregister_device(lp->idev); + kfree(lp); + + i2c_set_clientdata(client, NULL); + + return 0; +} + +#ifdef CONFIG_PM +static int pcf8574_kp_resume(struct i2c_client *client) +{ + enable_irq(client->irq); + + return 0; +} + +static int pcf8574_kp_suspend(struct i2c_client *client, pm_message_t mesg) +{ + disable_irq(client->irq); + + return 0; +} +#else +# define pcf8574_kp_resume NULL +# define pcf8574_kp_suspend NULL +#endif + +static const struct i2c_device_id pcf8574_kp_id[] = { + { DRV_NAME, 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, pcf8574_kp_id); + +static struct i2c_driver pcf8574_kp_driver = { + .driver = { + .name = DRV_NAME, + .owner = THIS_MODULE, + }, + .probe = pcf8574_kp_probe, + .remove = __devexit_p(pcf8574_kp_remove), + .suspend = pcf8574_kp_suspend, + .resume = pcf8574_kp_resume, + .id_table = pcf8574_kp_id, +}; + +static int __init pcf8574_kp_init(void) +{ + return i2c_add_driver(&pcf8574_kp_driver); +} +module_init(pcf8574_kp_init); + +static void __exit pcf8574_kp_exit(void) +{ + i2c_del_driver(&pcf8574_kp_driver); +} +module_exit(pcf8574_kp_exit); + +MODULE_AUTHOR("Michael Hennerich"); +MODULE_DESCRIPTION("Keypad input driver for 16 keys connected to PCF8574"); +MODULE_LICENSE("GPL"); |
