diff options
Diffstat (limited to 'drivers/i2c/chips/Kconfig')
| -rw-r--r-- | drivers/i2c/chips/Kconfig | 43 |
1 files changed, 38 insertions, 5 deletions
diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig index 2da2edfa68ec..50e0a4653741 100644 --- a/drivers/i2c/chips/Kconfig +++ b/drivers/i2c/chips/Kconfig @@ -14,6 +14,32 @@ config DS1682 This driver can also be built as a module. If so, the module will be called ds1682. +config AT24 + tristate "EEPROMs from most vendors" + depends on SYSFS && EXPERIMENTAL + help + Enable this driver to get read/write support to most I2C EEPROMs, + after you configure the driver to know about each EEPROM on + your target board. Use these generic chip names, instead of + vendor-specific ones like at24c64 or 24lc02: + + 24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08, + 24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024 + + Unless you like data loss puzzles, always be sure that any chip + you configure as a 24c32 (32 kbit) or larger is NOT really a + 24c16 (16 kbit) or smaller, and vice versa. Marking the chip + as read-only won't help recover from this. Also, if your chip + has any software write-protect mechanism you may want to review the + code to make sure this driver won't turn it on by accident. + + If you use this with an SMBus adapter instead of an I2C adapter, + full functionality is not available. Only smaller devices are + supported (24c16 and below, max 4 kByte). + + This driver can also be built as a module. If so, the module + will be called at24. + config SENSORS_EEPROM tristate "EEPROM reader" depends on EXPERIMENTAL @@ -26,8 +52,8 @@ config SENSORS_EEPROM will be called eeprom. config SENSORS_PCF8574 - tristate "Philips PCF8574 and PCF8574A" - depends on EXPERIMENTAL + tristate "Philips PCF8574 and PCF8574A (DEPRECATED)" + depends on EXPERIMENTAL && GPIO_PCF857X = "n" default n help If you say yes here you get support for Philips PCF8574 and @@ -36,12 +62,16 @@ config SENSORS_PCF8574 This driver can also be built as a module. If so, the module will be called pcf8574. + This driver is deprecated and will be dropped soon. Use + drivers/gpio/pcf857x.c instead. + These devices are hard to detect and rarely found on mainstream hardware. If unsure, say N. config PCF8575 - tristate "Philips PCF8575" + tristate "Philips PCF8575 (DEPRECATED)" default n + depends on GPIO_PCF857X = "n" help If you say yes here you get support for Philips PCF8575 chip. This chip is a 16-bit I/O expander for the I2C bus. Several other @@ -50,12 +80,15 @@ config PCF8575 This driver can also be built as a module. If so, the module will be called pcf8575. + This driver is deprecated and will be dropped soon. Use + drivers/gpio/pcf857x.c instead. + This device is hard to detect and is rarely found on mainstream hardware. If unsure, say N. config SENSORS_PCA9539 tristate "Philips PCA9539 16-bit I/O port (DEPRECATED)" - depends on EXPERIMENTAL && GPIO_PCA9539 = "n" + depends on EXPERIMENTAL && GPIO_PCA953X = "n" help If you say yes here you get support for the Philips PCA9539 16-bit I/O port. @@ -64,7 +97,7 @@ config SENSORS_PCA9539 will be called pca9539. This driver is deprecated and will be dropped soon. Use - drivers/gpio/pca9539.c instead. + drivers/gpio/pca953x.c instead. config SENSORS_PCF8591 tristate "Philips PCF8591" |
