diff options
Diffstat (limited to 'arch/x86/kernel/apic.c')
| -rw-r--r-- | arch/x86/kernel/apic.c | 213 |
1 files changed, 129 insertions, 84 deletions
diff --git a/arch/x86/kernel/apic.c b/arch/x86/kernel/apic.c index 115449f869ee..a894eea9d51a 100644 --- a/arch/x86/kernel/apic.c +++ b/arch/x86/kernel/apic.c @@ -1,7 +1,7 @@ /* * Local APIC handling, local APIC timers * - * (c) 1999, 2000 Ingo Molnar <mingo@redhat.com> + * (c) 1999, 2000, 2009 Ingo Molnar <mingo@redhat.com> * * Fixes * Maciej W. Rozycki : Bits for genuine 82489DX APICs; @@ -14,51 +14,71 @@ * Mikael Pettersson : PM converted to driver model. */ -#include <linux/init.h> - -#include <linux/mm.h> -#include <linux/delay.h> -#include <linux/bootmem.h> -#include <linux/interrupt.h> -#include <linux/mc146818rtc.h> #include <linux/kernel_stat.h> -#include <linux/sysdev.h> -#include <linux/ioport.h> -#include <linux/cpu.h> -#include <linux/clockchips.h> +#include <linux/mc146818rtc.h> #include <linux/acpi_pmtmr.h> +#include <linux/clockchips.h> +#include <linux/interrupt.h> +#include <linux/bootmem.h> +#include <linux/ftrace.h> +#include <linux/ioport.h> #include <linux/module.h> -#include <linux/dmi.h> +#include <linux/sysdev.h> +#include <linux/delay.h> +#include <linux/timex.h> #include <linux/dmar.h> -#include <linux/ftrace.h> -#include <linux/smp.h> +#include <linux/init.h> +#include <linux/cpu.h> +#include <linux/dmi.h> #include <linux/nmi.h> -#include <linux/timex.h> +#include <linux/smp.h> +#include <linux/mm.h> -#include <asm/atomic.h> -#include <asm/mtrr.h> -#include <asm/mpspec.h> -#include <asm/desc.h> #include <asm/arch_hooks.h> -#include <asm/hpet.h> #include <asm/pgalloc.h> +#include <asm/genapic.h> +#include <asm/atomic.h> +#include <asm/mpspec.h> #include <asm/i8253.h> -#include <asm/idle.h> +#include <asm/i8259.h> #include <asm/proto.h> #include <asm/apic.h> -#include <asm/i8259.h> +#include <asm/desc.h> +#include <asm/hpet.h> +#include <asm/idle.h> +#include <asm/mtrr.h> #include <asm/smp.h> -#include <mach_apic.h> -#include <mach_apicdef.h> -#include <mach_ipi.h> +unsigned int num_processors; + +unsigned disabled_cpus __cpuinitdata; + +/* Processor that is doing the boot up */ +unsigned int boot_cpu_physical_apicid = -1U; /* - * Sanity check + * The highest APIC ID seen during enumeration. + * + * This determines the messaging protocol we can use: if all APIC IDs + * are in the 0 ... 7 range, then we can use logical addressing which + * has some performance advantages (better broadcasting). + * + * If there's an APIC ID above 8, we use physical addressing. */ -#if ((SPURIOUS_APIC_VECTOR & 0x0F) != 0x0F) -# error SPURIOUS_APIC_VECTOR definition error -#endif +unsigned int max_physical_apicid; + +/* + * Bitmask of physically existing CPUs: + */ +physid_mask_t phys_cpu_present_map; + +/* + * Map cpu index to physical APIC ID + */ +DEFINE_EARLY_PER_CPU(u16, x86_cpu_to_apicid, BAD_APICID); +DEFINE_EARLY_PER_CPU(u16, x86_bios_cpu_apicid, BAD_APICID); +EXPORT_EARLY_PER_CPU_SYMBOL(x86_cpu_to_apicid); +EXPORT_EARLY_PER_CPU_SYMBOL(x86_bios_cpu_apicid); #ifdef CONFIG_X86_32 /* @@ -457,7 +477,7 @@ static void lapic_timer_setup(enum clock_event_mode mode, static void lapic_timer_broadcast(const struct cpumask *mask) { #ifdef CONFIG_SMP - send_IPI_mask(mask, LOCAL_TIMER_VECTOR); + apic->send_IPI_mask(mask, LOCAL_TIMER_VECTOR); #endif } @@ -535,7 +555,8 @@ static void __init lapic_cal_handler(struct clock_event_device *dev) } } -static int __init calibrate_by_pmtimer(long deltapm, long *delta) +static int __init +calibrate_by_pmtimer(long deltapm, long *delta, long *deltatsc) { const long pm_100ms = PMTMR_TICKS_PER_SEC / 10; const long pm_thresh = pm_100ms / 100; @@ -546,7 +567,7 @@ static int __init calibrate_by_pmtimer(long deltapm, long *delta) return -1; #endif - apic_printk(APIC_VERBOSE, "... PM timer delta = %ld\n", deltapm); + apic_printk(APIC_VERBOSE, "... PM-Timer delta = %ld\n", deltapm); /* Check, if the PM timer is available */ if (!deltapm) @@ -556,19 +577,30 @@ static int __init calibrate_by_pmtimer(long deltapm, long *delta) if (deltapm > (pm_100ms - pm_thresh) && deltapm < (pm_100ms + pm_thresh)) { - apic_printk(APIC_VERBOSE, "... PM timer result ok\n"); - } else { - res = (((u64)deltapm) * mult) >> 22; - do_div(res, 1000000); - pr_warning("APIC calibration not consistent " - "with PM Timer: %ldms instead of 100ms\n", - (long)res); - /* Correct the lapic counter value */ - res = (((u64)(*delta)) * pm_100ms); + apic_printk(APIC_VERBOSE, "... PM-Timer result ok\n"); + return 0; + } + + res = (((u64)deltapm) * mult) >> 22; + do_div(res, 1000000); + pr_warning("APIC calibration not consistent " + "with PM-Timer: %ldms instead of 100ms\n",(long)res); + + /* Correct the lapic counter value */ + res = (((u64)(*delta)) * pm_100ms); + do_div(res, deltapm); + pr_info("APIC delta adjusted to PM-Timer: " + "%lu (%ld)\n", (unsigned long)res, *delta); + *delta = (long)res; + + /* Correct the tsc counter value */ + if (cpu_has_tsc) { + res = (((u64)(*deltatsc)) * pm_100ms); do_div(res, deltapm); - pr_info("APIC delta adjusted to PM-Timer: " - "%lu (%ld)\n", (unsigned long)res, *delta); - *delta = (long)res; + apic_printk(APIC_VERBOSE, "TSC delta adjusted to " + "PM-Timer: %lu (%ld) \n", + (unsigned long)res, *deltatsc); + *deltatsc = (long)res; } return 0; @@ -579,7 +611,7 @@ static int __init calibrate_APIC_clock(void) struct clock_event_device *levt = &__get_cpu_var(lapic_events); void (*real_handler)(struct clock_event_device *dev); unsigned long deltaj; - long delta; + long delta, deltatsc; int pm_referenced = 0; local_irq_disable(); @@ -609,9 +641,11 @@ static int __init calibrate_APIC_clock(void) delta = lapic_cal_t1 - lapic_cal_t2; apic_printk(APIC_VERBOSE, "... lapic delta = %ld\n", delta); + deltatsc = (long)(lapic_cal_tsc2 - lapic_cal_tsc1); + /* we trust the PM based calibration if possible */ pm_referenced = !calibrate_by_pmtimer(lapic_cal_pm2 - lapic_cal_pm1, - &delta); + &delta, &deltatsc); /* Calculate the scaled math multiplication factor */ lapic_clockevent.mult = div_sc(delta, TICK_NSEC * LAPIC_CAL_LOOPS, @@ -629,11 +663,10 @@ static int __init calibrate_APIC_clock(void) calibration_result); if (cpu_has_tsc) { - delta = (long)(lapic_cal_tsc2 - lapic_cal_tsc1); apic_printk(APIC_VERBOSE, "..... CPU clock speed is " "%ld.%04ld MHz.\n", - (delta / LAPIC_CAL_LOOPS) / (1000000 / HZ), - (delta / LAPIC_CAL_LOOPS) % (1000000 / HZ)); + (deltatsc / LAPIC_CAL_LOOPS) / (1000000 / HZ), + (deltatsc / LAPIC_CAL_LOOPS) % (1000000 / HZ)); } apic_printk(APIC_VERBOSE, "..... host bus clock speed is " @@ -991,11 +1024,11 @@ int __init verify_local_APIC(void) */ reg0 = apic_read(APIC_ID); apic_printk(APIC_DEBUG, "Getting ID: %x\n", reg0); - apic_write(APIC_ID, reg0 ^ APIC_ID_MASK); + apic_write(APIC_ID, reg0 ^ apic->apic_id_mask); reg1 = apic_read(APIC_ID); apic_printk(APIC_DEBUG, "Getting ID: %x\n", reg1); apic_write(APIC_ID, reg0); - if (reg1 != (reg0 ^ APIC_ID_MASK)) + if (reg1 != (reg0 ^ apic->apic_id_mask)) return 0; /* @@ -1089,7 +1122,7 @@ static void __cpuinit lapic_setup_esr(void) return; } - if (esr_disable) { + if (apic->disable_esr) { /* * Something untraceable is creating bad interrupts on * secondary quads ... for the moment, just leave the @@ -1130,9 +1163,14 @@ void __cpuinit setup_local_APIC(void) unsigned int value; int i, j; + if (disable_apic) { + arch_disable_smp_support(); + return; + } + #ifdef CONFIG_X86_32 /* Pound the ESR really hard over the head with a big hammer - mbligh */ - if (lapic_is_integrated() && esr_disable) { + if (lapic_is_integrated() && apic->disable_esr) { apic_write(APIC_ESR, 0); apic_write(APIC_ESR, 0); apic_write(APIC_ESR, 0); @@ -1146,7 +1184,7 @@ void __cpuinit setup_local_APIC(void) * Double-check whether this APIC is really registered. * This is meaningless in clustered apic mode, so we skip it. */ - if (!apic_id_registered()) + if (!apic->apic_id_registered()) BUG(); /* @@ -1154,7 +1192,7 @@ void __cpuinit setup_local_APIC(void) * an APIC. See e.g. "AP-388 82489DX User's Manual" (Intel * document number 292116). So here it goes... */ - init_apic_ldr(); + apic->init_apic_ldr(); /* * Set Task Priority to 'accept all'. We never change this @@ -1570,11 +1608,11 @@ int apic_version[MAX_APICS]; int __init APIC_init_uniprocessor(void) { -#ifdef CONFIG_X86_64 if (disable_apic) { pr_info("Apic disabled\n"); return -1; } +#ifdef CONFIG_X86_64 if (!cpu_has_apic) { disable_apic = 1; pr_info("Apic disabled by BIOS\n"); @@ -1600,7 +1638,7 @@ int __init APIC_init_uniprocessor(void) enable_IR_x2apic(); #endif #ifdef CONFIG_X86_64 - setup_apic_routing(); + default_setup_apic_routing(); #endif verify_local_APIC(); @@ -1621,35 +1659,31 @@ int __init APIC_init_uniprocessor(void) physid_set_mask_of_physid(boot_cpu_physical_apicid, &phys_cpu_present_map); setup_local_APIC(); -#ifdef CONFIG_X86_64 +#ifdef CONFIG_X86_IO_APIC /* * Now enable IO-APICs, actually call clear_IO_APIC - * We need clear_IO_APIC before enabling vector on BP + * We need clear_IO_APIC before enabling error vector */ if (!skip_ioapic_setup && nr_ioapics) enable_IO_APIC(); #endif -#ifdef CONFIG_X86_IO_APIC - if (!smp_found_config || skip_ioapic_setup || !nr_ioapics) -#endif - localise_nmi_watchdog(); end_local_APIC_setup(); #ifdef CONFIG_X86_IO_APIC if (smp_found_config && !skip_ioapic_setup && nr_ioapics) setup_IO_APIC(); -# ifdef CONFIG_X86_64 - else + else { nr_ioapics = 0; -# endif + localise_nmi_watchdog(); + } +#else + localise_nmi_watchdog(); #endif + setup_boot_clock(); #ifdef CONFIG_X86_64 - setup_boot_APIC_clock(); check_nmi_watchdog(); -#else - setup_boot_clock(); #endif return 0; @@ -1738,7 +1772,8 @@ void __init connect_bsp_APIC(void) outb(0x01, 0x23); } #endif - enable_apic_mode(); + if (apic->enable_apic_mode) + apic->enable_apic_mode(); } /** @@ -1876,29 +1911,39 @@ void __cpuinit generic_processor_info(int apicid, int version) } #endif -#if defined(CONFIG_X86_SMP) || defined(CONFIG_X86_64) - /* are we being called early in kernel startup? */ - if (early_per_cpu_ptr(x86_cpu_to_apicid)) { - u16 *cpu_to_apicid = early_per_cpu_ptr(x86_cpu_to_apicid); - u16 *bios_cpu_apicid = early_per_cpu_ptr(x86_bios_cpu_apicid); - - cpu_to_apicid[cpu] = apicid; - bios_cpu_apicid[cpu] = apicid; - } else { - per_cpu(x86_cpu_to_apicid, cpu) = apicid; - per_cpu(x86_bios_cpu_apicid, cpu) = apicid; - } +#if defined(CONFIG_SMP) || defined(CONFIG_X86_64) + early_per_cpu(x86_cpu_to_apicid, cpu) = apicid; + early_per_cpu(x86_bios_cpu_apicid, cpu) = apicid; #endif set_cpu_possible(cpu, true); set_cpu_present(cpu, true); } -#ifdef CONFIG_X86_64 int hard_smp_processor_id(void) { return read_apic_id(); } + +void default_init_apic_ldr(void) +{ + unsigned long val; + + apic_write(APIC_DFR, APIC_DFR_VALUE); + val = apic_read(APIC_LDR) & ~APIC_LDR_MASK; + val |= SET_APIC_LOGICAL_ID(1UL << smp_processor_id()); + apic_write(APIC_LDR, val); +} + +#ifdef CONFIG_X86_32 +int default_apicid_to_node(int logical_apicid) +{ +#ifdef CONFIG_SMP + return apicid_2_node[hard_smp_processor_id()]; +#else + return 0; +#endif +} #endif /* |
