1 files changed, 0 insertions, 107 deletions
diff --git a/arch/v850/kernel/rte_ma1_cb.c b/arch/v850/kernel/rte_ma1_cb.c
deleted file mode 100644
index 08abf3d5f8df..000000000000
--- a/arch/v850/kernel/rte_ma1_cb.c
+++ /dev/null
@@ -1,107 +0,0 @@
-/*
- * arch/v850/kernel/rte_ma1_cb.c -- Midas labs RTE-V850E/MA1-CB board
- *
- *  Copyright (C) 2001,02,03  NEC Electronics Corporation
- *  Copyright (C) 2001,02,03  Miles Bader <miles@gnu.org>
- *
- * This file is subject to the terms and conditions of the GNU General
- * Public License.  See the file COPYING in the main directory of this
- * archive for more details.
- *
- * Written by Miles Bader <miles@gnu.org>
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/bootmem.h>
-
-#include <asm/atomic.h>
-#include <asm/page.h>
-#include <asm/ma1.h>
-#include <asm/rte_ma1_cb.h>
-#include <asm/v850e_timer_c.h>
-
-#include "mach.h"
-
-
-/* SRAM and SDRAM are almost contiguous (with a small hole in between;
-   see mach_reserve_bootmem for details), so just use both as one big area.  */
-#define RAM_START 	SRAM_ADDR
-#define RAM_END		(SDRAM_ADDR + SDRAM_SIZE)
-
-
-void __init mach_early_init (void)
-{
-	rte_cb_early_init ();
-}
-
-void __init mach_get_physical_ram (unsigned long *ram_start,
-				   unsigned long *ram_len)
-{
-	*ram_start = RAM_START;
-	*ram_len = RAM_END - RAM_START;
-}
-
-void __init mach_reserve_bootmem ()
-{
-#ifdef CONFIG_RTE_CB_MULTI
-	/* Prevent the kernel from touching the monitor's scratch RAM.  */
-	reserve_bootmem(MON_SCRATCH_ADDR, MON_SCRATCH_SIZE,
-			BOOTMEM_DEFAULT);
-#endif
-
-	/* The space between SRAM and SDRAM is filled with duplicate
-	   images of SRAM.  Prevent the kernel from using them.  */
-	reserve_bootmem (SRAM_ADDR + SRAM_SIZE,
-			 SDRAM_ADDR - (SRAM_ADDR + SRAM_SIZE),
-			 BOOTMEM_DEFAULT);
-}
-
-void mach_gettimeofday (struct timespec *tv)
-{
-	tv->tv_sec = 0;
-	tv->tv_nsec = 0;
-}
-
-/* Called before configuring an on-chip UART.  */
-void rte_ma1_cb_uart_pre_configure (unsigned chan,
-				    unsigned cflags, unsigned baud)
-{
-	/* The RTE-MA1-CB connects some general-purpose I/O pins on the
-	   CPU to the RTS/CTS lines of UART 0's serial connection.
-	   I/O pins P42 and P43 are RTS and CTS respectively.  */
-	if (chan == 0) {
-		/* Put P42 & P43 in I/O port mode.  */
-		MA_PORT4_PMC &= ~0xC;
-		/* Make P42 an output, and P43 an input.  */
-		MA_PORT4_PM = (MA_PORT4_PM & ~0xC) | 0x8;
-	}
-
-	/* Do pre-configuration for the actual UART.  */
-	ma_uart_pre_configure (chan, cflags, baud);
-}
-
-void __init mach_init_irqs (void)
-{
-	unsigned tc;
-
-	/* Initialize interrupts.  */
-	ma_init_irqs ();
-	rte_cb_init_irqs ();
-
-	/* Use falling-edge-sensitivity for interrupts .  */
-	V850E_TIMER_C_SESC (0) &= ~0xC;
-	V850E_TIMER_C_SESC (1) &= ~0xF;
-
-	/* INTP000-INTP011 are shared with `Timer C', so we have to set
-	   up Timer C to pass them through as raw interrupts.  */
-	for (tc = 0; tc < 2; tc++)
-		/* Turn on the timer.  */
-		V850E_TIMER_C_TMCC0 (tc) |= V850E_TIMER_C_TMCC0_CAE;
-
-	/* Make sure the relevant port0/port1 pins are assigned
-	   interrupt duty.  We used INTP001-INTP011 (don't screw with
-	   INTP000 because the monitor uses it).  */
-	MA_PORT0_PMC |= 0x4;	/* P02 (INTP001) in IRQ mode.  */
-	MA_PORT1_PMC |= 0x6;	/* P11 (INTP010) & P12 (INTP011) in IRQ mode.*/
-}