diff options
Diffstat (limited to 'arch/mips/alchemy/devboards/pb1500.c')
| -rw-r--r-- | arch/mips/alchemy/devboards/pb1500.c | 198 |
1 files changed, 198 insertions, 0 deletions
diff --git a/arch/mips/alchemy/devboards/pb1500.c b/arch/mips/alchemy/devboards/pb1500.c new file mode 100644 index 000000000000..e7b807b3ec51 --- /dev/null +++ b/arch/mips/alchemy/devboards/pb1500.c @@ -0,0 +1,198 @@ +/* + * Pb1500 board support. + * + * Copyright (C) 2009 Manuel Lauss + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <linux/delay.h> +#include <linux/dma-mapping.h> +#include <linux/gpio.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> +#include <asm/mach-au1x00/au1000.h> +#include <asm/mach-db1x00/bcsr.h> +#include <prom.h> +#include "platform.h" + +const char *get_system_type(void) +{ + return "PB1500"; +} + +void __init board_setup(void) +{ + u32 pin_func; + u32 sys_freqctrl, sys_clksrc; + + bcsr_init(DB1000_BCSR_PHYS_ADDR, + DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS); + + sys_clksrc = sys_freqctrl = pin_func = 0; + /* Set AUX clock to 12 MHz * 8 = 96 MHz */ + au_writel(8, SYS_AUXPLL); + alchemy_gpio1_input_enable(); + udelay(100); + + /* GPIO201 is input for PCMCIA card detect */ + /* GPIO203 is input for PCMCIA interrupt request */ + alchemy_gpio_direction_input(201); + alchemy_gpio_direction_input(203); + +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) + + /* Zero and disable FREQ2 */ + sys_freqctrl = au_readl(SYS_FREQCTRL0); + sys_freqctrl &= ~0xFFF00000; + au_writel(sys_freqctrl, SYS_FREQCTRL0); + + /* zero and disable USBH/USBD clocks */ + sys_clksrc = au_readl(SYS_CLKSRC); + sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK | + SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK); + au_writel(sys_clksrc, SYS_CLKSRC); + + sys_freqctrl = au_readl(SYS_FREQCTRL0); + sys_freqctrl &= ~0xFFF00000; + + sys_clksrc = au_readl(SYS_CLKSRC); + sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK | + SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK); + + /* FREQ2 = aux/2 = 48 MHz */ + sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2 | SYS_FC_FS2; + au_writel(sys_freqctrl, SYS_FREQCTRL0); + + /* + * Route 48MHz FREQ2 into USB Host and/or Device + */ + sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT; + au_writel(sys_clksrc, SYS_CLKSRC); + + pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB; + /* 2nd USB port is USB host */ + pin_func |= SYS_PF_USB; + au_writel(pin_func, SYS_PINFUNC); +#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */ + +#ifdef CONFIG_PCI + { + void __iomem *base = + (void __iomem *)KSEG1ADDR(AU1500_PCI_PHYS_ADDR); + /* Setup PCI bus controller */ + __raw_writel(0x00003fff, base + PCI_REG_CMEM); + __raw_writel(0xf0000000, base + PCI_REG_MWMASK_DEV); + __raw_writel(0, base + PCI_REG_MWBASE_REV_CCL); + __raw_writel(0x02a00356, base + PCI_REG_STATCMD); + __raw_writel(0x00003c04, base + PCI_REG_PARAM); + __raw_writel(0x00000008, base + PCI_REG_MBAR); + wmb(); + } +#endif + + /* Enable sys bus clock divider when IDLE state or no bus activity. */ + au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL); + + /* Enable the RTC if not already enabled */ + if (!(au_readl(0xac000028) & 0x20)) { + printk(KERN_INFO "enabling clock ...\n"); + au_writel((au_readl(0xac000028) | 0x20), 0xac000028); + } + /* Put the clock in BCD mode */ + if (au_readl(0xac00002c) & 0x4) { /* reg B */ + au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c); + au_sync(); + } +} + +/******************************************************************************/ + +static int pb1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin) +{ + if ((slot < 12) || (slot > 13) || pin == 0) + return -1; + if (slot == 12) + return (pin == 1) ? AU1500_PCI_INTA : 0xff; + if (slot == 13) { + switch (pin) { + case 1: return AU1500_PCI_INTA; + case 2: return AU1500_PCI_INTB; + case 3: return AU1500_PCI_INTC; + case 4: return AU1500_PCI_INTD; + } + } + return -1; +} + +static struct resource alchemy_pci_host_res[] = { + [0] = { + .start = AU1500_PCI_PHYS_ADDR, + .end = AU1500_PCI_PHYS_ADDR + 0xfff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct alchemy_pci_platdata pb1500_pci_pd = { + .board_map_irq = pb1500_map_pci_irq, + .pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H | + PCI_CONFIG_CH | +#if defined(__MIPSEB__) + PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM, +#else + 0, +#endif +}; + +static struct platform_device pb1500_pci_host = { + .dev.platform_data = &pb1500_pci_pd, + .name = "alchemy-pci", + .id = 0, + .num_resources = ARRAY_SIZE(alchemy_pci_host_res), + .resource = alchemy_pci_host_res, +}; + +static int __init pb1500_dev_init(void) +{ + int swapped; + + irq_set_irq_type(AU1500_GPIO9_INT, IRQF_TRIGGER_LOW); /* CD0# */ + irq_set_irq_type(AU1500_GPIO10_INT, IRQF_TRIGGER_LOW); /* CARD0 */ + irq_set_irq_type(AU1500_GPIO11_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */ + irq_set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH); + irq_set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW); + irq_set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW); + irq_set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW); + irq_set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW); + + /* PCMCIA. single socket, identical to Pb1100 */ + db1x_register_pcmcia_socket( + AU1000_PCMCIA_ATTR_PHYS_ADDR, + AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1, + AU1000_PCMCIA_MEM_PHYS_ADDR, + AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1, + AU1000_PCMCIA_IO_PHYS_ADDR, + AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1, + AU1500_GPIO11_INT, AU1500_GPIO9_INT, /* card / insert */ + /*AU1500_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */ + + swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT; + db1x_register_norflash(64 * 1024 * 1024, 4, swapped); + platform_device_register(&pb1500_pci_host); + + return 0; +} +arch_initcall(pb1500_dev_init); |
