diff options
Diffstat (limited to 'arch/i386/kernel/acpi/wakeup.S')
| -rw-r--r-- | arch/i386/kernel/acpi/wakeup.S | 318 |
1 files changed, 318 insertions, 0 deletions
diff --git a/arch/i386/kernel/acpi/wakeup.S b/arch/i386/kernel/acpi/wakeup.S new file mode 100644 index 000000000000..39d32484f6f5 --- /dev/null +++ b/arch/i386/kernel/acpi/wakeup.S @@ -0,0 +1,318 @@ +.text +#include <linux/linkage.h> +#include <asm/segment.h> +#include <asm/page.h> + +# +# wakeup_code runs in real mode, and at unknown address (determined at run-time). +# Therefore it must only use relative jumps/calls. +# +# Do we need to deal with A20? It is okay: ACPI specs says A20 must be enabled +# +# If physical address of wakeup_code is 0x12345, BIOS should call us with +# cs = 0x1234, eip = 0x05 +# + +ALIGN + .align 4096 +ENTRY(wakeup_start) +wakeup_code: + wakeup_code_start = . + .code16 + + movw $0xb800, %ax + movw %ax,%fs + movw $0x0e00 + 'L', %fs:(0x10) + + cli + cld + + # setup data segment + movw %cs, %ax + movw %ax, %ds # Make ds:0 point to wakeup_start + movw %ax, %ss + mov $(wakeup_stack - wakeup_code), %sp # Private stack is needed for ASUS board + movw $0x0e00 + 'S', %fs:(0x12) + + pushl $0 # Kill any dangerous flags + popfl + + movl real_magic - wakeup_code, %eax + cmpl $0x12345678, %eax + jne bogus_real_magic + + testl $1, video_flags - wakeup_code + jz 1f + lcall $0xc000,$3 + movw %cs, %ax + movw %ax, %ds # Bios might have played with that + movw %ax, %ss +1: + + testl $2, video_flags - wakeup_code + jz 1f + mov video_mode - wakeup_code, %ax + call mode_set +1: + + # set up page table + movl $swapper_pg_dir-__PAGE_OFFSET, %eax + movl %eax, %cr3 + + testl $1, real_efer_save_restore - wakeup_code + jz 4f + # restore efer setting + movl real_save_efer_edx - wakeup_code, %edx + movl real_save_efer_eax - wakeup_code, %eax + mov $0xc0000080, %ecx + wrmsr +4: + # make sure %cr4 is set correctly (features, etc) + movl real_save_cr4 - wakeup_code, %eax + movl %eax, %cr4 + movw $0xb800, %ax + movw %ax,%fs + movw $0x0e00 + 'i', %fs:(0x12) + + # need a gdt + lgdt real_save_gdt - wakeup_code + + movl real_save_cr0 - wakeup_code, %eax + movl %eax, %cr0 + jmp 1f +1: + movw $0x0e00 + 'n', %fs:(0x14) + + movl real_magic - wakeup_code, %eax + cmpl $0x12345678, %eax + jne bogus_real_magic + + ljmpl $__KERNEL_CS,$wakeup_pmode_return + +real_save_gdt: .word 0 + .long 0 +real_save_cr0: .long 0 +real_save_cr3: .long 0 +real_save_cr4: .long 0 +real_magic: .long 0 +video_mode: .long 0 +video_flags: .long 0 +real_efer_save_restore: .long 0 +real_save_efer_edx: .long 0 +real_save_efer_eax: .long 0 + +bogus_real_magic: + movw $0x0e00 + 'B', %fs:(0x12) + jmp bogus_real_magic + +/* This code uses an extended set of video mode numbers. These include: + * Aliases for standard modes + * NORMAL_VGA (-1) + * EXTENDED_VGA (-2) + * ASK_VGA (-3) + * Video modes numbered by menu position -- NOT RECOMMENDED because of lack + * of compatibility when extending the table. These are between 0x00 and 0xff. + */ +#define VIDEO_FIRST_MENU 0x0000 + +/* Standard BIOS video modes (BIOS number + 0x0100) */ +#define VIDEO_FIRST_BIOS 0x0100 + +/* VESA BIOS video modes (VESA number + 0x0200) */ +#define VIDEO_FIRST_VESA 0x0200 + +/* Video7 special modes (BIOS number + 0x0900) */ +#define VIDEO_FIRST_V7 0x0900 + +# Setting of user mode (AX=mode ID) => CF=success +mode_set: + movw %ax, %bx +#if 0 + cmpb $0xff, %ah + jz setalias + + testb $VIDEO_RECALC>>8, %ah + jnz _setrec + + cmpb $VIDEO_FIRST_RESOLUTION>>8, %ah + jnc setres + + cmpb $VIDEO_FIRST_SPECIAL>>8, %ah + jz setspc + + cmpb $VIDEO_FIRST_V7>>8, %ah + jz setv7 +#endif + + cmpb $VIDEO_FIRST_VESA>>8, %ah + jnc check_vesa +#if 0 + orb %ah, %ah + jz setmenu +#endif + + decb %ah +# jz setbios Add bios modes later + +setbad: clc + ret + +check_vesa: + subb $VIDEO_FIRST_VESA>>8, %bh + orw $0x4000, %bx # Use linear frame buffer + movw $0x4f02, %ax # VESA BIOS mode set call + int $0x10 + cmpw $0x004f, %ax # AL=4f if implemented + jnz _setbad # AH=0 if OK + + stc + ret + +_setbad: jmp setbad + + .code32 + ALIGN + +.org 0x800 +wakeup_stack_begin: # Stack grows down + +.org 0xff0 # Just below end of page +wakeup_stack: +ENTRY(wakeup_end) + +.org 0x1000 + +wakeup_pmode_return: + movw $__KERNEL_DS, %ax + movw %ax, %ss + movw %ax, %ds + movw %ax, %es + movw %ax, %fs + movw %ax, %gs + movw $0x0e00 + 'u', 0xb8016 + + # reload the gdt, as we need the full 32 bit address + lgdt saved_gdt + lidt saved_idt + lldt saved_ldt + ljmp $(__KERNEL_CS),$1f +1: + movl %cr3, %eax + movl %eax, %cr3 + wbinvd + + # and restore the stack ... but you need gdt for this to work + movl saved_context_esp, %esp + + movl %cs:saved_magic, %eax + cmpl $0x12345678, %eax + jne bogus_magic + + # jump to place where we left off + movl saved_eip,%eax + jmp *%eax + +bogus_magic: + movw $0x0e00 + 'B', 0xb8018 + jmp bogus_magic + + +## +# acpi_copy_wakeup_routine +# +# Copy the above routine to low memory. +# +# Parameters: +# %eax: place to copy wakeup routine to +# +# Returned address is location of code in low memory (past data and stack) +# +ENTRY(acpi_copy_wakeup_routine) + + sgdt saved_gdt + sidt saved_idt + sldt saved_ldt + str saved_tss + + movl nx_enabled, %edx + movl %edx, real_efer_save_restore - wakeup_start (%eax) + testl $1, real_efer_save_restore - wakeup_start (%eax) + jz 2f + # save efer setting + pushl %eax + movl %eax, %ebx + mov $0xc0000080, %ecx + rdmsr + movl %edx, real_save_efer_edx - wakeup_start (%ebx) + movl %eax, real_save_efer_eax - wakeup_start (%ebx) + popl %eax +2: + + movl %cr3, %edx + movl %edx, real_save_cr3 - wakeup_start (%eax) + movl %cr4, %edx + movl %edx, real_save_cr4 - wakeup_start (%eax) + movl %cr0, %edx + movl %edx, real_save_cr0 - wakeup_start (%eax) + sgdt real_save_gdt - wakeup_start (%eax) + + movl saved_videomode, %edx + movl %edx, video_mode - wakeup_start (%eax) + movl acpi_video_flags, %edx + movl %edx, video_flags - wakeup_start (%eax) + movl $0x12345678, real_magic - wakeup_start (%eax) + movl $0x12345678, saved_magic + ret + +.data +ALIGN +ENTRY(saved_magic) .long 0 +ENTRY(saved_eip) .long 0 + +save_registers: + leal 4(%esp), %eax + movl %eax, saved_context_esp + movl %ebx, saved_context_ebx + movl %ebp, saved_context_ebp + movl %esi, saved_context_esi + movl %edi, saved_context_edi + pushfl ; popl saved_context_eflags + + movl $ret_point, saved_eip + ret + + +restore_registers: + movl saved_context_ebp, %ebp + movl saved_context_ebx, %ebx + movl saved_context_esi, %esi + movl saved_context_edi, %edi + pushl saved_context_eflags ; popfl + ret + +ENTRY(do_suspend_lowlevel) + call save_processor_state + call save_registers + pushl $3 + call acpi_enter_sleep_state + addl $4, %esp + ret + .p2align 4,,7 +ret_point: + call restore_registers + call restore_processor_state + ret + +ENTRY(do_suspend_lowlevel_s4bios) + call save_processor_state + call save_registers + call acpi_enter_sleep_state_s4bios + ret + +ALIGN +# saved registers +saved_gdt: .long 0,0 +saved_idt: .long 0,0 +saved_ldt: .long 0 +saved_tss: .long 0 + |
