1 files changed, 0 insertions, 117 deletions
diff --git a/arch/cris/arch-v32/mach-fs/dram_init.S b/arch/cris/arch-v32/mach-fs/dram_init.S
deleted file mode 100644
index e1a01fa4c272..000000000000
--- a/arch/cris/arch-v32/mach-fs/dram_init.S
+++ /dev/null
@@ -1,117 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * DRAM/SDRAM initialization - alter with care
- * This file is intended to be included from other assembler files
- *
- * Note: This file may not modify r8 or r9 because they are used to
- * carry information from the decompressor to the kernel
- *
- * Copyright (C) 2000-2007 Axis Communications AB
- *
- * Authors:  Mikael Starvik <starvik@axis.com>
- */
-
-/* Just to be certain the config file is included, we include it here
- * explicitly instead of depending on it being included in the file that
- * uses this code.
- */
-
-#include <hwregs/asm/reg_map_asm.h>
-#include <hwregs/asm/bif_core_defs_asm.h>
-
-	;; WARNING! The registers r8 and r9 are used as parameters carrying
-	;; information from the decompressor (if the kernel was compressed).
-	;; They should not be used in the code below.
-
-	; Refer to BIF MDS for a description of SDRAM initialization
-
-	; Bank configuration
-	move.d   REG_ADDR(bif_core, regi_bif_core, rw_sdram_cfg_grp0), $r0
-	move.d   CONFIG_ETRAX_SDRAM_GRP0_CONFIG, $r1
-	move.d   $r1, [$r0]
-	move.d   REG_ADDR(bif_core, regi_bif_core, rw_sdram_cfg_grp1), $r0
-	move.d   CONFIG_ETRAX_SDRAM_GRP1_CONFIG, $r1
-	move.d   $r1, [$r0]
-
-	; Calculate value of mrs_data
-	; CAS latency = 2 && bus_width = 32 => 0x40
-	; CAS latency = 3 && bus_width = 32 => 0x60
-	; CAS latency = 2 && bus_width = 16 => 0x20
-	; CAS latency = 3 && bus_width = 16 => 0x30
-
-	; Check if value is already supplied in kernel config
-	move.d   CONFIG_ETRAX_SDRAM_COMMAND, $r2
-	bne	 _set_timing
-	nop
-
-	move.d   0x40, $r4       ; Assume 32 bits and CAS latency = 2
-	move.d   CONFIG_ETRAX_SDRAM_TIMING, $r1
-	and.d    0x07, $r1       ; Get CAS latency
-	cmpq	 2, $r1		 ; CL = 2 ?
-	beq	 _bw_check
-	nop
-	move.d   0x60, $r4
-
-_bw_check:
-	; Assume that group 0 width is equal to group 1. This assumption
-	; is wrong for a group 1 only hardware (such as the grand old
-	; StorPoint+).
-	move.d   CONFIG_ETRAX_SDRAM_GRP0_CONFIG, $r1
-	and.d    0x200, $r1	; DRAM width is bit 9
-	beq      _set_timing
-	lslq	 2, $r4		;  mrs_data starts at bit 2
-	lsrq     1, $r4		;  16 bits. Shift down value.
-
-	; Set timing parameters (refresh off to avoid Guinness TR 83)
-_set_timing:
-	move.d   CONFIG_ETRAX_SDRAM_TIMING, $r1
-	and.d    ~(3 << reg_bif_core_rw_sdram_timing___ref___lsb), $r1
-	move.d   REG_ADDR(bif_core, regi_bif_core, rw_sdram_timing), $r0
-	move.d   $r1, [$r0]
-
-	; Issue NOP command
-	move.d REG_ADDR(bif_core, regi_bif_core, rw_sdram_cmd), $r5
-	moveq regk_bif_core_nop, $r1
-	move.d $r1, [$r5]
-
-	; Wait 200us
-	move.d   10000, $r2
-1:	bne      1b
-	subq     1, $r2
-
-	; Issue initialization command sequence
-	lapc     _sdram_commands_start, $r2
-	lapc     _sdram_commands_end,  $r3
-1:	clear.d  $r6
-	move.b   [$r2+], $r6	; Load command
-	or.d     $r4, $r6	; Add calculated mrs
-	move.d   $r6, [$r5]	; Write rw_sdram_cmd
-	; Wait 80 ns between each command
-	move.d	 4000, $r7
-2:	bne	 2b
-	subq	 1, $r7
-	cmp.d    $r2, $r3	; Last command?
-	bne      1b
-	nop
-
-	; Start refresh
-	move.d   CONFIG_ETRAX_SDRAM_TIMING, $r1
-	move.d   REG_ADDR(bif_core, regi_bif_core, rw_sdram_timing), $r0
-	move.d   $r1, [$r0]
-
-	; Initialization finished
-	ba       _sdram_commands_end
-	nop
-
-_sdram_commands_start:
-	.byte   regk_bif_core_pre ; Precharge
-	.byte   regk_bif_core_ref ; refresh
-	.byte   regk_bif_core_ref ; refresh
-	.byte   regk_bif_core_ref ; refresh
-	.byte   regk_bif_core_ref ; refresh
-	.byte   regk_bif_core_ref ; refresh
-	.byte   regk_bif_core_ref ; refresh
-	.byte   regk_bif_core_ref ; refresh
-	.byte   regk_bif_core_ref ; refresh
-	.byte   regk_bif_core_mrs ; mrs
-_sdram_commands_end: