diff options
Diffstat (limited to 'arch/cris/arch-v10/Kconfig')
| -rw-r--r-- | arch/cris/arch-v10/Kconfig | 399 |
1 files changed, 0 insertions, 399 deletions
diff --git a/arch/cris/arch-v10/Kconfig b/arch/cris/arch-v10/Kconfig deleted file mode 100644 index d4015a931374..000000000000 --- a/arch/cris/arch-v10/Kconfig +++ /dev/null @@ -1,399 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -if ETRAX_ARCH_V10 - -menu "CRIS v10 options" - -# ETRAX 100LX v1 has a MMU "feature" requiring a low mapping -config CRIS_LOW_MAP - bool - depends on ETRAX_ARCH_V10 && ETRAX100LX - default y - -config ETRAX_DRAM_VIRTUAL_BASE - hex - depends on ETRAX_ARCH_V10 - default "c0000000" if !ETRAX100LX - default "60000000" if ETRAX100LX - -choice - prompt "Product LED port" - depends on ETRAX_ARCH_V10 - default ETRAX_PA_LEDS - -config ETRAX_PA_LEDS - bool "Port-PA-LEDs" - help - The ETRAX network driver is responsible for flashing LED's when - packets arrive and are sent. It uses macros defined in - <file:arch/cris/include/asm/io.h>, and those macros are defined after - what YOU choose in this option. The actual bits used are configured - separately. Select this if the LEDs are on port PA. Some products - put the leds on PB or a memory-mapped latch (CSP0) instead. - -config ETRAX_PB_LEDS - bool "Port-PB-LEDs" - help - The ETRAX network driver is responsible for flashing LED's when - packets arrive and are sent. It uses macros defined in - <file:arch/cris/include/asm/io.h>, and those macros are defined after - what YOU choose in this option. The actual bits used are configured - separately. Select this if the LEDs are on port PB. Some products - put the leds on PA or a memory-mapped latch (CSP0) instead. - -config ETRAX_CSP0_LEDS - bool "Port-CSP0-LEDs" - help - The ETRAX network driver is responsible for flashing LED's when - packets arrive and are sent. It uses macros defined in - <file:arch/cris/include/asm/io.h>, and those macros are defined after - what YOU choose in this option. The actual bits used are configured - separately. Select this if the LEDs are on a memory-mapped latch - using chip select CSP0, this is mapped at 0x90000000. - Some products put the leds on PA or PB instead. - -config ETRAX_NO_LEDS - bool "None" - help - Select this option if you don't have any LED at all. - -endchoice - -config ETRAX_LED1G - int "First green LED bit" - depends on ETRAX_ARCH_V10 && !ETRAX_NO_LEDS - default "2" - help - Bit to use for the first green LED. - Most Axis products use bit 2 here. - -config ETRAX_LED1R - int "First red LED bit" - depends on ETRAX_ARCH_V10 && !ETRAX_NO_LEDS - default "3" - help - Bit to use for the first red LED. - Most Axis products use bit 3 here. - For products with only one controllable LED, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED2G - int "Second green LED bit" - depends on ETRAX_ARCH_V10 && !ETRAX_NO_LEDS - default "4" - help - Bit to use for the second green LED. The "Active" LED. - Most Axis products use bit 4 here. - For products with only one controllable LED, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED2R - int "Second red LED bit" - depends on ETRAX_ARCH_V10 && !ETRAX_NO_LEDS - default "5" - help - Bit to use for the second red LED. - Most Axis products use bit 5 here. - For products with only one controllable LED, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED3G - int "Third green LED bit" - depends on ETRAX_ARCH_V10 && !ETRAX_NO_LEDS - default "2" - help - Bit to use for the third green LED. The "Drive" LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED3R - int "Third red LED bit" - depends on ETRAX_ARCH_V10 && !ETRAX_NO_LEDS - default "2" - help - Bit to use for the third red LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED4R - int "Fourth red LED bit" - depends on ETRAX_CSP0_LEDS - default "2" - help - Bit to use for the fourth red LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED4G - int "Fourth green LED bit" - depends on ETRAX_CSP0_LEDS - default "2" - help - Bit to use for the fourth green LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED5R - int "Fifth red LED bit" - depends on ETRAX_CSP0_LEDS - default "2" - help - Bit to use for the fifth red LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED5G - int "Fifth green LED bit" - depends on ETRAX_CSP0_LEDS - default "2" - help - Bit to use for the fifth green LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED6R - int "Sixth red LED bit" - depends on ETRAX_CSP0_LEDS - default "2" - help - Bit to use for the sixth red LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED6G - int "Sixth green LED bit" - depends on ETRAX_CSP0_LEDS - default "2" - help - Bit to use for the sixth green LED. The "Drive" LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED7R - int "Seventh red LED bit" - depends on ETRAX_CSP0_LEDS - default "2" - help - Bit to use for the seventh red LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED7G - int "Seventh green LED bit" - depends on ETRAX_CSP0_LEDS - default "2" - help - Bit to use for the seventh green LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED8Y - int "Eighth yellow LED bit" - depends on ETRAX_CSP0_LEDS - default "2" - help - Bit to use for the eighth yellow LED. The "Drive" LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED9Y - int "Ninth yellow LED bit" - depends on ETRAX_CSP0_LEDS - default "2" - help - Bit to use for the ninth yellow LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED10Y - int "Tenth yellow LED bit" - depends on ETRAX_CSP0_LEDS - default "2" - help - Bit to use for the tenth yellow LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED11Y - int "Eleventh yellow LED bit" - depends on ETRAX_CSP0_LEDS - default "2" - help - Bit to use for the eleventh yellow LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - -config ETRAX_LED12R - int "Twelfth red LED bit" - depends on ETRAX_CSP0_LEDS - default "2" - help - Bit to use for the twelfth red LED. - For products with only one or two controllable LEDs, - set this to same as CONFIG_ETRAX_LED1G (normally 2). - - -choice - prompt "Product rescue-port" - depends on ETRAX_ARCH_V10 - default ETRAX_RESCUE_SER0 - -config ETRAX_RESCUE_SER0 - bool "Serial-0" - help - Select one of the four serial ports as a rescue port. The default - is port 0. - -config ETRAX_RESCUE_SER1 - bool "Serial-1" - help - Use serial port 1 as the rescue port. - -config ETRAX_RESCUE_SER2 - bool "Serial-2" - help - Use serial port 2 as the rescue port. - -config ETRAX_RESCUE_SER3 - bool "Serial-3" - help - Use serial port 3 as the rescue port. - -endchoice - -config ETRAX_DEF_R_WAITSTATES - hex "R_WAITSTATES" - depends on ETRAX_ARCH_V10 - default "95a6" - help - Waitstates for SRAM, Flash and peripherals (not DRAM). 95f8 is a - good choice for most Axis products... - -config ETRAX_DEF_R_BUS_CONFIG - hex "R_BUS_CONFIG" - depends on ETRAX_ARCH_V10 - default "104" - help - Assorted bits controlling write mode, DMA burst length etc. 104 is - a good choice for most Axis products... - -config ETRAX_SDRAM - bool "SDRAM support" - depends on ETRAX_ARCH_V10 - help - Enable this if you use SDRAM chips and configure - R_SDRAM_CONFIG and R_SDRAM_TIMING as well. - -config ETRAX_DEF_R_DRAM_CONFIG - hex "R_DRAM_CONFIG" - depends on ETRAX_ARCH_V10 && !ETRAX_SDRAM - default "1a200040" - help - The R_DRAM_CONFIG register specifies everything on how the DRAM - chips in the system are connected to the ETRAX CPU. This is - different depending on the manufacturer, chip type and number of - chips. So this value often needs to be different for each Axis - product. - -config ETRAX_DEF_R_DRAM_TIMING - hex "R_DRAM_TIMING" - depends on ETRAX_ARCH_V10 && !ETRAX_SDRAM - default "5611" - help - Different DRAM chips have different speeds. Current Axis products - use 50ns DRAM chips which can use the timing: 5611. - -config ETRAX_DEF_R_SDRAM_CONFIG - hex "R_SDRAM_CONFIG" - depends on ETRAX_ARCH_V10 && ETRAX_SDRAM - default "d2fa7878" - help - The R_SDRAM_CONFIG register specifies everything on how the SDRAM - chips in the system are connected to the ETRAX CPU. This is - different depending on the manufacturer, chip type and number of - chips. So this value often needs to be different for each Axis - product. - -config ETRAX_DEF_R_SDRAM_TIMING - hex "R_SDRAM_TIMING" - depends on ETRAX_ARCH_V10 && ETRAX_SDRAM - default "80004801" - help - Different SDRAM chips have different timing. - -config ETRAX_DEF_R_PORT_PA_DIR - hex "R_PORT_PA_DIR" - depends on ETRAX_ARCH_V10 - default "1c" - help - Configures the direction of general port A bits. 1 is out, 0 is in. - This is often totally different depending on the product used. - There are some guidelines though - if you know that only LED's are - connected to port PA, then they are usually connected to bits 2-4 - and you can therefore use 1c. On other boards which don't have the - LED's at the general ports, these bits are used for all kinds of - stuff. If you don't know what to use, it is always safe to put all - as inputs, although floating inputs isn't good. - -config ETRAX_DEF_R_PORT_PA_DATA - hex "R_PORT_PA_DATA" - depends on ETRAX_ARCH_V10 - default "00" - help - Configures the initial data for the general port A bits. Most - products should use 00 here. - -config ETRAX_DEF_R_PORT_PB_CONFIG - hex "R_PORT_PB_CONFIG" - depends on ETRAX_ARCH_V10 - default "00" - help - Configures the type of the general port B bits. 1 is chip select, - 0 is port. Most products should use 00 here. - -config ETRAX_DEF_R_PORT_PB_DIR - hex "R_PORT_PB_DIR" - depends on ETRAX_ARCH_V10 - default "00" - help - Configures the direction of general port B bits. 1 is out, 0 is in. - This is often totally different depending on the product used. Bits - 0 and 1 on port PB are usually used for I2C communication, but the - kernel I2C driver sets the appropriate directions itself so you - don't need to take that into consideration when setting this option. - If you don't know what to use, it is always safe to put all as - inputs. - -config ETRAX_DEF_R_PORT_PB_DATA - hex "R_PORT_PB_DATA" - depends on ETRAX_ARCH_V10 - default "ff" - help - Configures the initial data for the general port A bits. Most - products should use FF here. - -config ETRAX_SOFT_SHUTDOWN - bool "Software Shutdown Support" - depends on ETRAX_ARCH_V10 - help - Enable this if ETRAX is used with a power-supply that can be turned - off and on with PS_ON signal. Gives the possibility to detect - powerbutton and then do a power off after unmounting disks. - -config ETRAX_SHUTDOWN_BIT - int "Shutdown bit on port CSP0" - depends on ETRAX_SOFT_SHUTDOWN - default "12" - help - Configure what pin on CSPO-port that is used for controlling power - supply. - -config ETRAX_POWERBUTTON_BIT - int "Power button bit on port G" - depends on ETRAX_SOFT_SHUTDOWN - default "25" - help - Configure where power button is connected. - -endmenu - -endif |
