diff options
Diffstat (limited to 'arch/blackfin/mach-bf533')
| -rw-r--r-- | arch/blackfin/mach-bf533/Kconfig | 92 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf533/Makefile | 9 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf533/boards/Makefile | 8 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf533/boards/cm_bf533.c | 267 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf533/boards/ezkit.c | 224 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf533/boards/generic_board.c | 95 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf533/boards/stamp.c | 321 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf533/cpu.c | 161 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf533/head.S | 774 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf533/ints-priority.c | 65 |
10 files changed, 2016 insertions, 0 deletions
diff --git a/arch/blackfin/mach-bf533/Kconfig b/arch/blackfin/mach-bf533/Kconfig new file mode 100644 index 000000000000..14297b3ed5c3 --- /dev/null +++ b/arch/blackfin/mach-bf533/Kconfig @@ -0,0 +1,92 @@ +if (BF533 || BF532 || BF531) + +menu "BF533/2/1 Specific Configuration" + +comment "Interrupt Priority Assignment" +menu "Priority" + +config UART_ERROR + int "UART ERROR" + default 7 +config SPORT0_ERROR + int "SPORT0 ERROR" + default 7 +config SPI_ERROR + int "SPI ERROR" + default 7 +config SPORT1_ERROR + int "SPORT1 ERROR" + default 7 +config PPI_ERROR + int "PPI ERROR" + default 7 +config DMA_ERROR + int "DMA ERROR" + default 7 +config PLLWAKE_ERROR + int "PLL WAKEUP ERROR" + default 7 + +config RTC_ERROR + int "RTC ERROR" + default 8 +config DMA0_PPI + int "DMA0 PPI" + default 8 + +config DMA1_SPORT0RX + int "DMA1 (SPORT0 RX)" + default 9 +config DMA2_SPORT0TX + int "DMA2 (SPORT0 TX)" + default 9 +config DMA3_SPORT1RX + int "DMA3 (SPORT1 RX)" + default 9 +config DMA4_SPORT1TX + int "DMA4 (SPORT1 TX)" + default 9 +config DMA5_SPI + int "DMA5 (SPI)" + default 10 +config DMA6_UARTRX + int "DMA6 (UART0 RX)" + default 10 +config DMA7_UARTTX + int "DMA7 (UART0 TX)" + default 10 +config TIMER0 + int "TIMER0" + default 11 +config TIMER1 + int "TIMER1" + default 11 +config TIMER2 + int "TIMER2" + default 11 +config PFA + int "PF Interrupt A" + default 12 +config PFB + int "PF Interrupt B" + default 12 +config MEMDMA0 + int "MEMORY DMA0" + default 13 +config MEMDMA1 + int "MEMORY DMA1" + default 13 +config WDTIMER + int "WATCH DOG TIMER" + default 13 + + help + Enter the priority numbers between 7-13 ONLY. Others are Reserved. + This applies to all the above. It is not recommended to assign the + highest priority number 7 to UART or any other device. + +endmenu + +endmenu + +endif diff --git a/arch/blackfin/mach-bf533/Makefile b/arch/blackfin/mach-bf533/Makefile new file mode 100644 index 000000000000..76d2c2b8579a --- /dev/null +++ b/arch/blackfin/mach-bf533/Makefile @@ -0,0 +1,9 @@ +# +# arch/blackfin/mach-bf533/Makefile +# + +extra-y := head.o + +obj-y := ints-priority.o + +obj-$(CONFIG_CPU_FREQ_BF533) += cpu.o diff --git a/arch/blackfin/mach-bf533/boards/Makefile b/arch/blackfin/mach-bf533/boards/Makefile new file mode 100644 index 000000000000..12a631ab389d --- /dev/null +++ b/arch/blackfin/mach-bf533/boards/Makefile @@ -0,0 +1,8 @@ +# +# arch/blackfin/mach-bf533/boards/Makefile +# + +obj-$(CONFIG_GENERIC_BOARD) += generic_board.o +obj-$(CONFIG_BFIN533_STAMP) += stamp.o +obj-$(CONFIG_BFIN533_EZKIT) += ezkit.o +obj-$(CONFIG_BFIN533_BLUETECHNIX_CM) += cm_bf533.o diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c new file mode 100644 index 000000000000..23a7f607df3f --- /dev/null +++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c @@ -0,0 +1,267 @@ +/* + * File: arch/blackfin/mach-bf533/boards/cm_bf533.c + * Based on: arch/blackfin/mach-bf533/boards/ezkit.c + * Author: Aidan Williams <aidan@nicta.com.au> Copright 2005 + * + * Created: 2005 + * Description: Board description file + * + * Modified: + * Copyright 2004-2006 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/spi/spi.h> +#include <linux/spi/flash.h> +#include <linux/usb_isp1362.h> +#include <asm/irq.h> +#include <asm/bfin5xx_spi.h> + +/* + * Name the Board for the /proc/cpuinfo + */ +char *bfin_board_name = "Bluetechnix CM BF533"; + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +/* all SPI peripherals info goes here */ + +static struct mtd_partition bfin_spi_flash_partitions[] = { + { + .name = "bootloader", + .size = 0x00020000, + .offset = 0, + .mask_flags = MTD_CAP_ROM + },{ + .name = "kernel", + .size = 0xe0000, + .offset = 0x20000 + },{ + .name = "file system", + .size = 0x700000, + .offset = 0x00100000, + } +}; + +static struct flash_platform_data bfin_spi_flash_data = { + .name = "m25p80", + .parts = bfin_spi_flash_partitions, + .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), + .type = "m25p64", +}; + +/* SPI flash chip (m25p64) */ +static struct bfin5xx_spi_chip spi_flash_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ + .bits_per_word = 8, +}; + +/* SPI ADC chip */ +static struct bfin5xx_spi_chip spi_adc_chip_info = { + .enable_dma = 1, /* use dma transfer with this chip*/ + .bits_per_word = 16, +}; + +#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) +static struct bfin5xx_spi_chip ad1836_spi_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; +#endif + +static struct spi_board_info bfin_spi_board_info[] __initdata = { + { + /* the modalias must be the same as spi device driver name */ + .modalias = "m25p80", /* Name of spi_driver for this device */ + .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, /* Framework bus number */ + .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/ + .platform_data = &bfin_spi_flash_data, + .controller_data = &spi_flash_chip_info, + .mode = SPI_MODE_3, + },{ + .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */ + .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, /* Framework bus number */ + .chip_select = 2, /* Framework chip select. */ + .platform_data = NULL, /* No spi_driver specific config */ + .controller_data = &spi_adc_chip_info, + }, +#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) + { + .modalias = "ad1836-spi", + .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, + .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, + .controller_data = &ad1836_spi_chip_info, + }, +#endif +}; + +/* SPI controller data */ +static struct bfin5xx_spi_master spi_bfin_master_info = { + .num_chipselect = 8, + .enable_dma = 1, /* master has the ability to do dma transfer */ +}; + +static struct platform_device spi_bfin_master_device = { + .name = "bfin-spi-master", + .id = 1, /* Bus number */ + .dev = { + .platform_data = &spi_bfin_master_info, /* Passed to driver */ + }, +}; +#endif /* spi master and devices */ + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +static struct platform_device rtc_device = { + .name = "rtc-bfin", + .id = -1, +}; +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +static struct resource smc91x_resources[] = { + { + .start = 0x20200300, + .end = 0x20200300 + 16, + .flags = IORESOURCE_MEM, + },{ + .start = IRQ_PF0, + .end = IRQ_PF0, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = 0, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) +static struct resource bfin_uart_resources[] = { + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device bfin_uart_device = { + .name = "bfin-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_uart_resources), + .resource = bfin_uart_resources, +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) +static struct platform_device bfin_sport0_uart_device = { + .name = "bfin-sport-uart", + .id = 0, +}; + +static struct platform_device bfin_sport1_uart_device = { + .name = "bfin-sport-uart", + .id = 1, +}; +#endif + +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +static struct resource isp1362_hcd_resources[] = { + { + .start = 0x20308000, + .end = 0x20308000, + .flags = IORESOURCE_MEM, + },{ + .start = 0x20308004, + .end = 0x20308004, + .flags = IORESOURCE_MEM, + },{ + .start = IRQ_PF4, + .end = IRQ_PF4, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct isp1362_platform_data isp1362_priv = { + .sel15Kres = 1, + .clknotstop = 0, + .oc_enable = 0, + .int_act_high = 0, + .int_edge_triggered = 0, + .remote_wakeup_connected = 0, + .no_power_switching = 1, + .power_switching_mode = 0, +}; + +static struct platform_device isp1362_hcd_device = { + .name = "isp1362-hcd", + .id = 0, + .dev = { + .platform_data = &isp1362_priv, + }, + .num_resources = ARRAY_SIZE(isp1362_hcd_resources), + .resource = isp1362_hcd_resources, +}; +#endif + +static struct platform_device *cm_bf533_devices[] __initdata = { +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) + &bfin_uart_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) + &bfin_sport0_uart_device, + &bfin_sport1_uart_device, +#endif + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) + &rtc_device, +#endif + +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) + &isp1362_hcd_device, +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) + &smc91x_device, +#endif + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + &spi_bfin_master_device, +#endif +}; + +static int __init cm_bf533_init(void) +{ + printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__); + platform_add_devices(cm_bf533_devices, ARRAY_SIZE(cm_bf533_devices)); +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); +#endif + return 0; +} + +arch_initcall(cm_bf533_init); diff --git a/arch/blackfin/mach-bf533/boards/ezkit.c b/arch/blackfin/mach-bf533/boards/ezkit.c new file mode 100644 index 000000000000..747298ea907b --- /dev/null +++ b/arch/blackfin/mach-bf533/boards/ezkit.c @@ -0,0 +1,224 @@ +/* + * File: arch/blackfin/mach-bf533/ezkit.c + * Based on: Orginal Work + * Author: Aidan Williams <aidan@nicta.com.au> + * + * Created: 2005 + * Description: + * + * Modified: Robin Getz <rgetz@blackfin.uclinux.org> - Named the boards + * Copyright 2005 National ICT Australia (NICTA) + * Copyright 2004-2006 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/spi/spi.h> +#include <linux/spi/flash.h> +#include <linux/usb_isp1362.h> +#include <asm/irq.h> +#include <asm/bfin5xx_spi.h> + +/* + * Name the Board for the /proc/cpuinfo + */ +char *bfin_board_name = "ADDS-BF533-EZKIT"; + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +static struct platform_device rtc_device = { + .name = "rtc-bfin", + .id = -1, +}; +#endif + +/* + * USB-LAN EzExtender board + * Driver needs to know address, irq and flag pin. + */ +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +static struct resource smc91x_resources[] = { + { + .name = "smc91x-regs", + .start = 0x20310300, + .end = 0x20310300 + 16, + .flags = IORESOURCE_MEM, + },{ + .start = IRQ_PF9, + .end = IRQ_PF9, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = 0, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, +}; +#endif + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +/* all SPI peripherals info goes here */ + +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) +static struct mtd_partition bfin_spi_flash_partitions[] = { + { + .name = "bootloader", + .size = 0x00020000, + .offset = 0, + .mask_flags = MTD_CAP_ROM + },{ + .name = "kernel", + .size = 0xe0000, + .offset = 0x20000 + },{ + .name = "file system", + .size = 0x700000, + .offset = 0x00100000, + } +}; + +static struct flash_platform_data bfin_spi_flash_data = { + .name = "m25p80", + .parts = bfin_spi_flash_partitions, + .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), + .type = "m25p64", +}; + +/* SPI flash chip (m25p64) */ +static struct bfin5xx_spi_chip spi_flash_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE) +/* SPI ADC chip */ +static struct bfin5xx_spi_chip spi_adc_chip_info = { + .enable_dma = 1, /* use dma transfer with this chip*/ + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) +static struct bfin5xx_spi_chip ad1836_spi_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; +#endif + +static struct spi_board_info bfin_spi_board_info[] __initdata = { +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) + { + /* the modalias must be the same as spi device driver name */ + .modalias = "m25p80", /* Name of spi_driver for this device */ + .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, /* Framework bus number */ + .chip_select = 2, /* Framework chip select. On STAMP537 it is SPISSEL2*/ + .platform_data = &bfin_spi_flash_data, + .controller_data = &spi_flash_chip_info, + .mode = SPI_MODE_3, + }, +#endif + +#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE) + { + .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */ + .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, /* Framework bus number */ + .chip_select = 1, /* Framework chip select. */ + .platform_data = NULL, /* No spi_driver specific config */ + .controller_data = &spi_adc_chip_info, + }, +#endif + +#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) + { + .modalias = "ad1836-spi", + .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, + .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, + .controller_data = &ad1836_spi_chip_info, + }, +#endif +}; + +/* SPI controller data */ +static struct bfin5xx_spi_master spi_bfin_master_info = { + .num_chipselect = 8, + .enable_dma = 1, /* master has the ability to do dma transfer */ +}; + +static struct platform_device spi_bfin_master_device = { + .name = "bfin-spi-master", + .id = 1, /* Bus number */ + .dev = { + .platform_data = &spi_bfin_master_info, /* Passed to driver */ + }, +}; +#endif /* spi master and devices */ + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) +static struct resource bfin_uart_resources[] = { + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device bfin_uart_device = { + .name = "bfin-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_uart_resources), + .resource = bfin_uart_resources, +}; +#endif + +static struct platform_device *ezkit_devices[] __initdata = { +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) + &smc91x_device, +#endif + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + &spi_bfin_master_device, +#endif + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) + &rtc_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) + &bfin_uart_device, +#endif +}; + +static int __init ezkit_init(void) +{ + printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__); + platform_add_devices(ezkit_devices, ARRAY_SIZE(ezkit_devices)); +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); +#endif + return 0; +} + +arch_initcall(ezkit_init); diff --git a/arch/blackfin/mach-bf533/boards/generic_board.c b/arch/blackfin/mach-bf533/boards/generic_board.c new file mode 100644 index 000000000000..c0f43ccfbfb5 --- /dev/null +++ b/arch/blackfin/mach-bf533/boards/generic_board.c @@ -0,0 +1,95 @@ +/* + * File: arch/blackfin/mach-bf533/generic_board.c + * Based on: arch/blackfin/mach-bf533/ezkit.c + * Author: Aidan Williams <aidan@nicta.com.au> + * + * Created: 2005 + * Description: + * + * Modified: + * Copyright 2005 National ICT Australia (NICTA) + * Copyright 2004-2006 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <linux/device.h> +#include <linux/platform_device.h> +#include <asm/irq.h> + +/* + * Name the Board for the /proc/cpuinfo + */ +char *bfin_board_name = "UNKNOWN BOARD"; + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +static struct platform_device rtc_device = { + .name = "rtc-bfin", + .id = -1, +}; +#endif + +/* + * Driver needs to know address, irq and flag pin. + */ +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +static struct resource smc91x_resources[] = { + { + .start = 0x20300300, + .end = 0x20300300 + 16, + .flags = IORESOURCE_MEM, + },{ + .start = IRQ_PROG_INTB, + .end = IRQ_PROG_INTB, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + },{ + /* + * denotes the flag pin and is used directly if + * CONFIG_IRQCHIP_DEMUX_GPIO is defined. + */ + .start = IRQ_PF7, + .end = IRQ_PF7, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = 0, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, +}; +#endif + +static struct platform_device *generic_board_devices[] __initdata = { +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) + &rtc_device, +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) + &smc91x_device, +#endif +}; + +static int __init generic_board_init(void) +{ + printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__); + return platform_add_devices(generic_board_devices, ARRAY_SIZE(generic_board_devices)); +} + +arch_initcall(generic_board_init); diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c new file mode 100644 index 000000000000..d7b3a5d74e8c --- /dev/null +++ b/arch/blackfin/mach-bf533/boards/stamp.c @@ -0,0 +1,321 @@ +/* + * File: arch/blackfin/mach-bf533/stamp.c + * Based on: arch/blackfin/mach-bf533/ezkit.c + * Author: Aidan Williams <aidan@nicta.com.au> + * + * Created: 2005 + * Description: Board Info File for the BF533-STAMP + * + * Modified: + * Copyright 2005 National ICT Australia (NICTA) + * Copyright 2004-2006 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/spi/spi.h> +#include <linux/spi/flash.h> +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +#include <linux/usb_isp1362.h> +#endif +#include <asm/irq.h> +#include <asm/bfin5xx_spi.h> + +/* + * Name the Board for the /proc/cpuinfo + */ +char *bfin_board_name = "ADDS-BF533-STAMP"; + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +static struct platform_device rtc_device = { + .name = "rtc-bfin", + .id = -1, +}; +#endif + +/* + * Driver needs to know address, irq and flag pin. + */ +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +static struct resource smc91x_resources[] = { + { + .name = "smc91x-regs", + .start = 0x20300300, + .end = 0x20300300 + 16, + .flags = IORESOURCE_MEM, + },{ + .start = IRQ_PF7, + .end = IRQ_PF7, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = 0, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, +}; +#endif + +#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) +static struct resource net2272_bfin_resources[] = { + { + .start = 0x20300000, + .end = 0x20300000 + 0x100, + .flags = IORESOURCE_MEM, + },{ + .start = IRQ_PF10, + .end = IRQ_PF10, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct platform_device net2272_bfin_device = { + .name = "net2272", + .id = -1, + .num_resources = ARRAY_SIZE(net2272_bfin_resources), + .resource = net2272_bfin_resources, +}; +#endif + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +/* all SPI peripherals info goes here */ + +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) +static struct mtd_partition bfin_spi_flash_partitions[] = { + { + .name = "bootloader", + .size = 0x00020000, + .offset = 0, + .mask_flags = MTD_CAP_ROM + },{ + .name = "kernel", + .size = 0xe0000, + .offset = 0x20000 + },{ + .name = "file system", + .size = 0x700000, + .offset = 0x00100000, + } +}; + +static struct flash_platform_data bfin_spi_flash_data = { + .name = "m25p80", + .parts = bfin_spi_flash_partitions, + .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), + .type = "m25p64", +}; + +/* SPI flash chip (m25p64) */ +static struct bfin5xx_spi_chip spi_flash_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE) +/* SPI ADC chip */ +static struct bfin5xx_spi_chip spi_adc_chip_info = { + .enable_dma = 1, /* use dma transfer with this chip*/ + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) +static struct bfin5xx_spi_chip ad1836_spi_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_PBX) +static struct bfin5xx_spi_chip spi_si3xxx_chip_info = { + .ctl_reg = 0x4, /* send zero */ + .enable_dma = 0, + .bits_per_word = 8, + .cs_change_per_word = 1, +}; +#endif + +#if defined(CONFIG_AD5304) || defined(CONFIG_AD5304_MODULE) +static struct bfin5xx_spi_chip ad5304_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; +#endif + +static struct spi_board_info bfin_spi_board_info[] __initdata = { +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) + { + /* the modalias must be the same as spi device driver name */ + .modalias = "m25p80", /* Name of spi_driver for this device */ + .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, /* Framework bus number */ + .chip_select = 2, /* Framework chip select. On STAMP537 it is SPISSEL2*/ + .platform_data = &bfin_spi_flash_data, + .controller_data = &spi_flash_chip_info, + .mode = SPI_MODE_3, + }, +#endif + +#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE) + { + .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */ + .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, /* Framework bus number */ + .chip_select = 1, /* Framework chip select. */ + .platform_data = NULL, /* No spi_driver specific config */ + .controller_data = &spi_adc_chip_info, + }, +#endif + +#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) + { + .modalias = "ad1836-spi", + .max_speed_hz = 31250000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, + .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, + .controller_data = &ad1836_spi_chip_info, + }, +#endif + +#if defined(CONFIG_PBX) + { + .modalias = "fxs-spi", + .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, + .chip_select = 3, + .controller_data= &spi_si3xxx_chip_info, + .mode = SPI_MODE_3, + }, + { + .modalias = "fxo-spi", + .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, + .chip_select = 2, + .controller_data= &spi_si3xxx_chip_info, + .mode = SPI_MODE_3, + }, +#endif + +#if defined(CONFIG_AD5304) || defined(CONFIG_AD5304_MODULE) + { + .modalias = "ad5304_spi", + .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, + .chip_select = 2, + .platform_data = NULL, + .controller_data = &ad5304_chip_info, + .mode = SPI_MODE_2, + }, +#endif +}; + +/* SPI controller data */ +static struct bfin5xx_spi_master spi_bfin_master_info = { + .num_chipselect = 8, + .enable_dma = 1, /* master has the ability to do dma transfer */ +}; + +static struct platform_device spi_bfin_master_device = { + .name = "bfin-spi-master", + .id = 1, /* Bus number */ + .dev = { + .platform_data = &spi_bfin_master_info, /* Passed to driver */ + }, +}; +#endif /* spi master and devices */ + +#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE) +static struct platform_device bfin_fb_device = { + .name = "bf537-fb", +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) +static struct resource bfin_uart_resources[] = { + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device bfin_uart_device = { + .name = "bfin-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_uart_resources), + .resource = bfin_uart_resources, +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) +static struct platform_device bfin_sport0_uart_device = { + .name = "bfin-sport-uart", + .id = 0, +}; + +static struct platform_device bfin_sport1_uart_device = { + .name = "bfin-sport-uart", + .id = 1, +}; +#endif + +static struct platform_device *stamp_devices[] __initdata = { +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) + &rtc_device, +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) + &smc91x_device, +#endif + +#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) + &net2272_bfin_device, +#endif + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + &spi_bfin_master_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) + &bfin_uart_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) + &bfin_sport0_uart_device, + &bfin_sport1_uart_device, +#endif +}; + +static int __init stamp_init(void) +{ + printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__); + platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices)); +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); +#endif + return 0; +} + +arch_initcall(stamp_init); diff --git a/arch/blackfin/mach-bf533/cpu.c b/arch/blackfin/mach-bf533/cpu.c new file mode 100644 index 000000000000..99547c4c290e --- /dev/null +++ b/arch/blackfin/mach-bf533/cpu.c @@ -0,0 +1,161 @@ +/* + * File: arch/blackfin/mach-bf533/cpu.c + * Based on: + * Author: michael.kang@analog.com + * + * Created: + * Description: clock scaling for the bf533 + * + * Modified: + * Copyright 2004-2006 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/init.h> +#include <linux/cpufreq.h> +#include <asm/dpmc.h> +#include <linux/fs.h> +#include <asm/bfin-global.h> + +/* CONFIG_CLKIN_HZ=11059200 */ +#define VCO5 (CONFIG_CLKIN_HZ*45) /*497664000 */ +#define VCO4 (CONFIG_CLKIN_HZ*36) /*398131200 */ +#define VCO3 (CONFIG_CLKIN_HZ*27) /*298598400 */ +#define VCO2 (CONFIG_CLKIN_HZ*18) /*199065600 */ +#define VCO1 (CONFIG_CLKIN_HZ*9) /*99532800 */ +#define VCO(x) VCO##x + +#define FREQ(x) {VCO(x),VCO(x)/4},{VCO(x),VCO(x)/2},{VCO(x),VCO(x)} +/* frequency */ +static struct cpufreq_frequency_table bf533_freq_table[] = { + FREQ(1), + FREQ(3), + {VCO4, VCO4 / 2}, {VCO4, VCO4}, + FREQ(5), + {0, CPUFREQ_TABLE_END}, +}; + +/* + * dpmc_fops->ioctl() + * static int dpmc_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg) + */ +static int bf533_getfreq(unsigned int cpu) +{ + unsigned long cclk_mhz, vco_mhz; + + /* The driver only support single cpu */ + if (cpu == 0) + dpmc_fops.ioctl(NULL, NULL, IOCTL_GET_CORECLOCK, &cclk_mhz); + else + cclk_mhz = -1; + return cclk_mhz; +} + +static int bf533_target(struct cpufreq_policy *policy, + unsigned int target_freq, unsigned int relation) +{ + unsigned long cclk_mhz; + unsigned long vco_mhz; + unsigned long flags; + unsigned int index, vco_index; + int i; + + struct cpufreq_freqs freqs; + if (cpufreq_frequency_table_target + (policy, bf533_freq_table, target_freq, relation, &index)) + return -EINVAL; + cclk_mhz = bf533_freq_table[index].frequency; + vco_mhz = bf533_freq_table[index].index; + + dpmc_fops.ioctl(NULL, NULL, IOCTL_CHANGE_FREQUENCY, &vco_mhz); + freqs.old = bf533_getfreq(0); + freqs.new = cclk_mhz; + freqs.cpu = 0; + + pr_debug("cclk begin change to cclk %d,vco=%d,index=%d,target=%d,oldfreq=%d\n", + cclk_mhz, vco_mhz, index, target_freq, freqs.old); + + cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); + local_irq_save(flags); + dpmc_fops.ioctl(NULL, NULL, IOCTL_SET_CCLK, &cclk_mhz); + local_irq_restore(flags); + cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); + + vco_mhz = get_vco(); + cclk_mhz = get_cclk(); + return 0; +} + +/* make sure that only the "userspace" governor is run -- anything else wouldn't make sense on + * this platform, anyway. + */ +static int bf533_verify_speed(struct cpufreq_policy *policy) +{ + return cpufreq_frequency_table_verify(policy, &bf533_freq_table); +} + +static int __init __bf533_cpu_init(struct cpufreq_policy *policy) +{ + int result; + + if (policy->cpu != 0) + return -EINVAL; + + policy->governor = CPUFREQ_DEFAULT_GOVERNOR; + + policy->cpuinfo.transition_latency = CPUFREQ_ETERNAL; + /*Now ,only support one cpu */ + policy->cur = bf533_getfreq(0); + cpufreq_frequency_table_get_attr(bf533_freq_table, policy->cpu); + return cpufreq_frequency_table_cpuinfo(policy, bf533_freq_table); +} + +static struct freq_attr *bf533_freq_attr[] = { + &cpufreq_freq_attr_scaling_available_freqs, + NULL, +}; + +static struct cpufreq_driver bf533_driver = { + .verify = bf533_verify_speed, + .target = bf533_target, + .get = bf533_getfreq, + .init = __bf533_cpu_init, + .name = "bf533", + .owner = THIS_MODULE, + .attr = bf533_freq_attr, +}; + +static int __init bf533_cpu_init(void) +{ + return cpufreq_register_driver(&bf533_driver); +} + +static void __exit bf533_cpu_exit(void) +{ + cpufreq_unregister_driver(&bf533_driver); +} + +MODULE_AUTHOR("Mickael Kang"); +MODULE_DESCRIPTION("cpufreq driver for BF533 CPU"); +MODULE_LICENSE("GPL"); + +module_init(bf533_cpu_init); +module_exit(bf533_cpu_exit); diff --git a/arch/blackfin/mach-bf533/head.S b/arch/blackfin/mach-bf533/head.S new file mode 100644 index 000000000000..4808edb0680f --- /dev/null +++ b/arch/blackfin/mach-bf533/head.S @@ -0,0 +1,774 @@ +/* + * File: arch/blackfin/mach-bf533/head.S + * Based on: + * Author: Jeff Dionne <jeff@uclinux.org> COPYRIGHT 1998 D. Jeff Dionne + * + * Created: 1998 + * Description: bf533 startup file + * + * Modified: + * Copyright 2004-2006 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <linux/linkage.h> +#include <asm/blackfin.h> +#if CONFIG_BFIN_KERNEL_CLOCK +#include <asm/mach/mem_init.h> +#endif +#if CONFIG_DEBUG_KERNEL_START +#include <asm/mach-common/def_LPBlackfin.h> +#endif + +.global __rambase +.global __ramstart +.global __ramend +.extern ___bss_stop +.extern ___bss_start +.extern _bf53x_relocate_l1_mem + +#define INITIAL_STACK 0xFFB01000 + +.text + +ENTRY(__start) +ENTRY(__stext) + /* R0: argument of command line string, passed from uboot, save it */ + R7 = R0; + /* Set the SYSCFG register */ + R0 = 0x36; + /*Enable Cycle Counter and Nesting Of Interrupts(3rd Bit)*/ + SYSCFG = R0; + R0 = 0; + + /*Clear Out All the data and pointer Registers*/ + R1 = R0; + R2 = R0; + R3 = R0; + R4 = R0; + R5 = R0; + R6 = R0; + + P0 = R0; + P1 = R0; + P2 = R0; + P3 = R0; + P4 = R0; + P5 = R0; + + LC0 = r0; + LC1 = r0; + L0 = r0; + L1 = r0; + L2 = r0; + L3 = r0; + + /* Clear Out All the DAG Registers*/ + B0 = r0; + B1 = r0; + B2 = r0; + B3 = r0; + + I0 = r0; + I1 = r0; + I2 = r0; + I3 = r0; + + M0 = r0; + M1 = r0; + M2 = r0; + M3 = r0; + +#if CONFIG_DEBUG_KERNEL_START + +/* + * Set up a temporary Event Vector Table, so if something bad happens before + * the kernel is fully started, it doesn't vector off into the bootloaders + * table + */ + P0.l = lo(EVT2); + P0.h = hi(EVT2); + P1.l = lo(EVT15); + P1.h = hi(EVT15); + P2.l = debug_kernel_start_trap; + P2.h = debug_kernel_start_trap; + + RTS = P2; + RTI = P2; + RTX = P2; + RTN = P2; + RTE = P2; + +.Lfill_temp_vector_table: + [P0++] = P2; /* Core Event Vector Table */ + CC = P0 == P1; + if !CC JUMP .Lfill_temp_vector_table + P0 = r0; + P1 = r0; + P2 = r0; + +#endif + + p0.h = hi(FIO_MASKA_C); + p0.l = lo(FIO_MASKA_C); + r0 = 0xFFFF(Z); + w[p0] = r0.L; /* Disable all interrupts */ + ssync; + + p0.h = hi(FIO_MASKB_C); + p0.l = lo(FIO_MASKB_C); + r0 = 0xFFFF(Z); + w[p0] = r0.L; /* Disable all interrupts */ + ssync; + + /* Turn off the icache */ + p0.l = (IMEM_CONTROL & 0xFFFF); + p0.h = (IMEM_CONTROL >> 16); + R1 = [p0]; + R0 = ~ENICPLB; + R0 = R0 & R1; + + /* Anomaly 05000125 */ +#ifdef ANOMALY_05000125 + CLI R2; + SSYNC; +#endif + [p0] = R0; + SSYNC; +#ifdef ANOMALY_05000125 + STI R2; +#endif + + /* Turn off the dcache */ + p0.l = (DMEM_CONTROL & 0xFFFF); + p0.h = (DMEM_CONTROL >> 16); + R1 = [p0]; + R0 = ~ENDCPLB; + R0 = R0 & R1; + + /* Anomaly 05000125 */ +#ifdef ANOMALY_05000125 + CLI R2; + SSYNC; +#endif + [p0] = R0; + SSYNC; +#ifdef ANOMALY_05000125 + STI R2; +#endif + + /* Initialise UART */ + p0.h = hi(UART_LCR); + p0.l = lo(UART_LCR); + r0 = 0x0(Z); + w[p0] = r0.L; /* To enable DLL writes */ + ssync; + + p0.h = hi(UART_DLL); + p0.l = lo(UART_DLL); + r0 = 0x0(Z); + w[p0] = r0.L; + ssync; + + p0.h = hi(UART_DLH); + p0.l = lo(UART_DLH); + r0 = 0x00(Z); + w[p0] = r0.L; + ssync; + + p0.h = hi(UART_GCTL); + p0.l = lo(UART_GCTL); + r0 = 0x0(Z); + w[p0] = r0.L; /* To enable UART clock */ + ssync; + + /* Initialize stack pointer */ + sp.l = lo(INITIAL_STACK); + sp.h = hi(INITIAL_STACK); + fp = sp; + usp = sp; + + /* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */ + call _bf53x_relocate_l1_mem; +#if CONFIG_BFIN_KERNEL_CLOCK + call _start_dma_code; +#endif + + /* Code for initializing Async memory banks */ + + p2.h = hi(EBIU_AMBCTL1); + p2.l = lo(EBIU_AMBCTL1); + r0.h = hi(AMBCTL1VAL); + r0.l = lo(AMBCTL1VAL); + [p2] = r0; + ssync; + + p2.h = hi(EBIU_AMBCTL0); + p2.l = lo(EBIU_AMBCTL0); + r0.h = hi(AMBCTL0VAL); + r0.l = lo(AMBCTL0VAL); + [p2] = r0; + ssync; + + p2.h = hi(EBIU_AMGCTL); + p2.l = lo(EBIU_AMGCTL); + r0 = AMGCTLVAL; + w[p2] = r0; + ssync; + + /* This section keeps the processor in supervisor mode + * during kernel boot. Switches to user mode at end of boot. + * See page 3-9 of Hardware Reference manual for documentation. + */ + + /* EVT15 = _real_start */ + + p0.l = lo(EVT15); + p0.h = hi(EVT15); + p1.l = _real_start; + p1.h = _real_start; + [p0] = p1; + csync; + + p0.l = lo(IMASK); + p0.h = hi(IMASK); + p1.l = IMASK_IVG15; + p1.h = 0x0; + [p0] = p1; + csync; + + raise 15; + p0.l = .LWAIT_HERE; + p0.h = .LWAIT_HERE; + reti = p0; +#if defined(ANOMALY_05000281) + nop; nop; nop; +#endif + rti; + +.LWAIT_HERE: + jump .LWAIT_HERE; + +ENTRY(_real_start) + [ -- sp ] = reti; + p0.l = lo(WDOG_CTL); + p0.h = hi(WDOG_CTL); + r0 = 0xAD6(z); + w[p0] = r0; /* watchdog off for now */ + ssync; + + /* Code update for BSS size == 0 + * Zero out the bss region. + */ + + p1.l = ___bss_start; + p1.h = ___bss_start; + p2.l = ___bss_stop; + p2.h = ___bss_stop; + r0 = 0; + p2 -= p1; + lsetup (.L_clear_bss, .L_clear_bss) lc0 = p2; +.L_clear_bss: + B[p1++] = r0; + + /* In case there is a NULL pointer reference + * Zero out region before stext + */ + + p1.l = 0x0; + p1.h = 0x0; + r0.l = __stext; + r0.h = __stext; + r0 = r0 >> 1; + p2 = r0; + r0 = 0; + lsetup (.L_clear_zero, .L_clear_zero) lc0 = p2; +.L_clear_zero: + W[p1++] = r0; + +/* pass the uboot arguments to the global value command line */ + R0 = R7; + call _cmdline_init; + + p1.l = __rambase; + p1.h = __rambase; + r0.l = __sdata; + r0.h = __sdata; + [p1] = r0; + + p1.l = __ramstart; + p1.h = __ramstart; + p3.l = ___bss_stop; + p3.h = ___bss_stop; + + r1 = p3; + [p1] = r1; + + /* + * load the current thread pointer and stack + */ + r1.l = _init_thread_union; + r1.h = _init_thread_union; + + r2.l = 0x2000; + r2.h = 0x0000; + r1 = r1 + r2; + sp = r1; + usp = sp; + fp = sp; + call _start_kernel; +.L_exit: + jump.s .L_exit; + +.section .l1.text +#if CONFIG_BFIN_KERNEL_CLOCK +ENTRY(_start_dma_code) + p0.h = hi(SIC_IWR); + p0.l = lo(SIC_IWR); + r0.l = 0x1; + r0.h = 0x0; + [p0] = r0; + SSYNC; + + /* + * Set PLL_CTL + * - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors + * - [8] = BYPASS : BYPASS the PLL, run CLKIN into CCLK/SCLK + * - [7] = output delay (add 200ps of delay to mem signals) + * - [6] = input delay (add 200ps of input delay to mem signals) + * - [5] = PDWN : 1=All Clocks off + * - [3] = STOPCK : 1=Core Clock off + * - [1] = PLL_OFF : 1=Disable Power to PLL + * - [0] = DF : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL + * all other bits set to zero + */ + + p0.h = hi(PLL_LOCKCNT); + p0.l = lo(PLL_LOCKCNT); + r0 = 0x300(Z); + w[p0] = r0.l; + ssync; + + P2.H = hi(EBIU_SDGCTL); + P2.L = lo(EBIU_SDGCTL); + R0 = [P2]; + BITSET (R0, 24); + [P2] = R0; + SSYNC; + + r0 = CONFIG_VCO_MULT & 63; /* Load the VCO multiplier */ + r0 = r0 << 9; /* Shift it over, */ + r1 = CLKIN_HALF; /* Do we need to divide CLKIN by 2?*/ + r0 = r1 | r0; + r1 = PLL_BYPASS; /* Bypass the PLL? */ + r1 = r1 << 8; /* Shift it over */ + r0 = r1 | r0; /* add them all together */ + + p0.h = hi(PLL_CTL); + p0.l = lo(PLL_CTL); /* Load the address */ + cli r2; /* Disable interrupts */ + ssync; + w[p0] = r0.l; /* Set the value */ + idle; /* Wait for the PLL to stablize */ + sti r2; /* Enable interrupts */ + +.Lcheck_again: + p0.h = hi(PLL_STAT); + p0.l = lo(PLL_STAT); + R0 = W[P0](Z); + CC = BITTST(R0,5); + if ! CC jump .Lcheck_again; + + /* Configure SCLK & CCLK Dividers */ + r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV); + p0.h = hi(PLL_DIV); + p0.l = lo(PLL_DIV); + w[p0] = r0.l; + ssync; + + p0.l = lo(EBIU_SDRRC); + p0.h = hi(EBIU_SDRRC); + r0 = mem_SDRRC; + w[p0] = r0.l; + ssync; + + p0.l = (EBIU_SDBCTL & 0xFFFF); + p0.h = (EBIU_SDBCTL >> 16); /* SDRAM Memory Bank Control Register */ + r0 = mem_SDBCTL; + w[p0] = r0.l; + ssync; + + P2.H = hi(EBIU_SDGCTL); + P2.L = lo(EBIU_SDGCTL); + R0 = [P2]; + BITCLR (R0, 24); + p0.h = hi(EBIU_SDSTAT); + p0.l = lo(EBIU_SDSTAT); + r2.l = w[p0]; + cc = bittst(r2,3); + if !cc jump .Lskip; + NOP; + BITSET (R0, 23); +.Lskip: + [P2] = R0; + SSYNC; + + R0.L = lo(mem_SDGCTL); + R0.H = hi(mem_SDGCTL); + R1 = [p2]; + R1 = R1 | R0; + [P2] = R1; + SSYNC; + + p0.h = hi(SIC_IWR); + p0.l = lo(SIC_IWR); + r0.l = lo(IWR_ENABLE_ALL) + r0.h = hi(IWR_ENABLE_ALL) + [p0] = r0; + SSYNC; + + RTS; +#endif /* CONFIG_BFIN_KERNEL_CLOCK */ + +ENTRY(_bfin_reset) + /* No more interrupts to be handled*/ + CLI R6; + SSYNC; + +#if defined(CONFIG_BFIN_SHARED_FLASH_ENET) + p0.h = hi(FIO_INEN); + p0.l = lo(FIO_INEN); + r0.l = ~(1 << CONFIG_ENET_FLASH_PIN); + w[p0] = r0.l; + + p0.h = hi(FIO_DIR); + p0.l = lo(FIO_DIR); + r0.l = (1 << CONFIG_ENET_FLASH_PIN); + w[p0] = r0.l; + + p0.h = hi(FIO_FLAG_C); + p0.l = lo(FIO_FLAG_C); + r0.l = (1 << CONFIG_ENET_FLASH_PIN); + w[p0] = r0.l; +#endif + + /* Clear the bits 13-15 in SWRST if they werent cleared */ + p0.h = hi(SWRST); + p0.l = lo(SWRST); + csync; + r0.l = w[p0]; + + /* Clear the IMASK register */ + p0.h = hi(IMASK); + p0.l = lo(IMASK); + r0 = 0x0; + [p0] = r0; + + /* Clear the ILAT register */ + p0.h = hi(ILAT); + p0.l = lo(ILAT); + r0 = [p0]; + [p0] = r0; + SSYNC; + + /* Disable the WDOG TIMER */ + p0.h = hi(WDOG_CTL); + p0.l = lo(WDOG_CTL); + r0.l = 0xAD6; + w[p0] = r0.l; + SSYNC; + + /* Clear the sticky bit incase it is already set */ + p0.h = hi(WDOG_CTL); + p0.l = lo(WDOG_CTL); + r0.l = 0x8AD6; + w[p0] = r0.l; + SSYNC; + + /* Program the count value */ + R0.l = 0x100; + R0.h = 0x0; + P0.h = hi(WDOG_CNT); + P0.l = lo(WDOG_CNT); + [P0] = R0; + SSYNC; + + /* Program WDOG_STAT if necessary */ + P0.h = hi(WDOG_CTL); + P0.l = lo(WDOG_CTL); + R0 = W[P0](Z); + CC = BITTST(R0,1); + if !CC JUMP .LWRITESTAT; + CC = BITTST(R0,2); + if !CC JUMP .LWRITESTAT; + JUMP .LSKIP_WRITE; + +.LWRITESTAT: + /* When watch dog timer is enabled, a write to STAT will load the contents of CNT to STAT */ + R0 = 0x0000(z); + P0.h = hi(WDOG_STAT); + P0.l = lo(WDOG_STAT) + [P0] = R0; + SSYNC; + +.LSKIP_WRITE: + /* Enable the reset event */ + P0.h = hi(WDOG_CTL); + P0.l = lo(WDOG_CTL); + R0 = W[P0](Z); + BITCLR(R0,1); + BITCLR(R0,2); + W[P0] = R0.L; + SSYNC; + NOP; + + /* Enable the wdog counter */ + R0 = W[P0](Z); + BITCLR(R0,4); + W[P0] = R0.L; + SSYNC; + + IDLE; + + RTS; + +#if CONFIG_DEBUG_KERNEL_START +debug_kernel_start_trap: + /* Set up a temp stack in L1 - SDRAM might not be working */ + P0.L = lo(L1_DATA_A_START + 0x100); + P0.H = hi(L1_DATA_A_START + 0x100); + SP = P0; + + /* Make sure the Clocks are the way I think they should be */ + r0 = CONFIG_VCO_MULT & 63; /* Load the VCO multiplier */ + r0 = r0 << 9; /* Shift it over, */ + r1 = CLKIN_HALF; /* Do we need to divide CLKIN by 2?*/ + r0 = r1 | r0; + r1 = PLL_BYPASS; /* Bypass the PLL? */ + r1 = r1 << 8; /* Shift it over */ + r0 = r1 | r0; /* add them all together */ + + p0.h = hi(PLL_CTL); + p0.l = lo(PLL_CTL); /* Load the address */ + cli r2; /* Disable interrupts */ + ssync; + w[p0] = r0.l; /* Set the value */ + idle; /* Wait for the PLL to stablize */ + sti r2; /* Enable interrupts */ + +.Lcheck_again1: + p0.h = hi(PLL_STAT); + p0.l = lo(PLL_STAT); + R0 = W[P0](Z); + CC = BITTST(R0,5); + if ! CC jump .Lcheck_again1; + + /* Configure SCLK & CCLK Dividers */ + r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV); + p0.h = hi(PLL_DIV); + p0.l = lo(PLL_DIV); + w[p0] = r0.l; + ssync; + + /* Make sure UART is enabled - you can never be sure */ + +/* + * Setup for console. Argument comes from the menuconfig + */ + +#ifdef CONFIG_BAUD_9600 +#define CONSOLE_BAUD_RATE 9600 +#elif CONFIG_BAUD_19200 +#define CONSOLE_BAUD_RATE 19200 +#elif CONFIG_BAUD_38400 +#define CONSOLE_BAUD_RATE 38400 +#elif CONFIG_BAUD_57600 +#define CONSOLE_BAUD_RATE 57600 +#elif CONFIG_BAUD_115200 +#define CONSOLE_BAUD_RATE 115200 +#endif + + p0.h = hi(UART_GCTL); + p0.l = lo(UART_GCTL); + r0 = 0x00(Z); + w[p0] = r0.L; /* To Turn off UART clocks */ + ssync; + + p0.h = hi(UART_LCR); + p0.l = lo(UART_LCR); + r0 = 0x83(Z); + w[p0] = r0.L; /* To enable DLL writes */ + ssync; + + R1 = (((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT) / CONFIG_SCLK_DIV) / (CONSOLE_BAUD_RATE * 16)); + + p0.h = hi(UART_DLL); + p0.l = lo(UART_DLL); + r0 = 0xFF(Z); + r0 = R1 & R0; + w[p0] = r0.L; + ssync; + + p0.h = hi(UART_DLH); + p0.l = lo(UART_DLH); + r1 >>= 8 ; + w[p0] = r1.L; + ssync; + + p0.h = hi(UART_GCTL); + p0.l = lo(UART_GCTL); + r0 = 0x0(Z); + w[p0] = r0.L; /* To enable UART clock */ + ssync; + + p0.h = hi(UART_LCR); + p0.l = lo(UART_LCR); + r0 = 0x03(Z); + w[p0] = r0.L; /* To Turn on UART */ + ssync; + + p0.h = hi(UART_GCTL); + p0.l = lo(UART_GCTL); + r0 = 0x01(Z); + w[p0] = r0.L; /* To Turn on UART Clocks */ + ssync; + + P0.h = hi(UART_THR); + P0.l = lo(UART_THR); + P1.h = hi(UART_LSR); + P1.l = lo(UART_LSR); + + R0.L = 'K'; + call .Lwait_char; + R0.L='e'; + call .Lwait_char; + R0.L='r'; + call .Lwait_char; + R0.L='n' + call .Lwait_char; + R0.L='e' + call .Lwait_char; + R0.L='l'; + call .Lwait_char; + R0.L=' '; + call .Lwait_char; + R0.L='c'; + call .Lwait_char; + R0.L='r'; + call .Lwait_char; + R0.L='a'; + call .Lwait_char; + R0.L='s'; + call .Lwait_char; + R0.L='h'; + call .Lwait_char; + R0.L='\r'; + call .Lwait_char; + R0.L='\n'; + call .Lwait_char; + + R0.L='S'; + call .Lwait_char; + R0.L='E'; + call .Lwait_char; + R0.L='Q' + call .Lwait_char; + R0.L='S' + call .Lwait_char; + R0.L='T'; + call .Lwait_char; + R0.L='A'; + call .Lwait_char; + R0.L='T'; + call .Lwait_char; + R0.L='='; + call .Lwait_char; + R2 = SEQSTAT; + call .Ldump_reg; + + R0.L=' '; + call .Lwait_char; + R0.L='R'; + call .Lwait_char; + R0.L='E' + call .Lwait_char; + R0.L='T' + call .Lwait_char; + R0.L='X'; + call .Lwait_char; + R0.L='='; + call .Lwait_char; + R2 = RETX; + call .Ldump_reg; + + R0.L='\r'; + call .Lwait_char; + R0.L='\n'; + call .Lwait_char; + +.Ldebug_kernel_start_trap_done: + JUMP .Ldebug_kernel_start_trap_done; +.Ldump_reg: + R3 = 32; + R4 = 0x0F; + R5 = ':'; /* one past 9 */ + +.Ldump_reg2: + R0 = R2; + R3 += -4; + R0 >>>= R3; + R0 = R0 & R4; + R0 += 0x30; + CC = R0 <= R5; + if CC JUMP .Ldump_reg1; + R0 += 7; + +.Ldump_reg1: + R1.l = W[P1]; + CC = BITTST(R1, 5); + if !CC JUMP .Ldump_reg1; + W[P0] = r0; + + CC = R3 == 0; + if !CC JUMP .Ldump_reg2 + RTS; + +.Lwait_char: + R1.l = W[P1]; + CC = BITTST(R1, 5); + if !CC JUMP .Lwait_char; + W[P0] = r0; + RTS; + +#endif /* CONFIG_DEBUG_KERNEL_START */ + +.data + +/* + * Set up the usable of RAM stuff. Size of RAM is determined then + * an initial stack set up at the end. + */ + +.align 4 +__rambase: +.long 0 +__ramstart: +.long 0 +__ramend: +.long 0 diff --git a/arch/blackfin/mach-bf533/ints-priority.c b/arch/blackfin/mach-bf533/ints-priority.c new file mode 100644 index 000000000000..36a693345204 --- /dev/null +++ b/arch/blackfin/mach-bf533/ints-priority.c @@ -0,0 +1,65 @@ +/* + * File: arch/blackfin/mach-bf533/ints-priority.c + * Based on: + * Author: Michael Hennerich + * + * Created: ? + * Description: Set up the interupt priorities + * + * Modified: + * Copyright 2004-2006 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <linux/module.h> +#include <asm/blackfin.h> +#include <asm/irq.h> + +void program_IAR(void) +{ + /* Program the IAR0 Register with the configured priority */ + bfin_write_SIC_IAR0(((CONFIG_PLLWAKE_ERROR - 7) << PLLWAKE_ERROR_POS) | + ((CONFIG_DMA_ERROR - 7) << DMA_ERROR_POS) | + ((CONFIG_PPI_ERROR - 7) << PPI_ERROR_POS) | + ((CONFIG_SPORT0_ERROR - 7) << SPORT0_ERROR_POS) | + ((CONFIG_SPI_ERROR - 7) << SPI_ERROR_POS) | + ((CONFIG_SPORT1_ERROR - 7) << SPORT1_ERROR_POS) | + ((CONFIG_UART_ERROR - 7) << UART_ERROR_POS) | + ((CONFIG_RTC_ERROR - 7) << RTC_ERROR_POS)); + + bfin_write_SIC_IAR1(((CONFIG_DMA0_PPI - 7) << DMA0_PPI_POS) | + ((CONFIG_DMA1_SPORT0RX - 7) << DMA1_SPORT0RX_POS) | + ((CONFIG_DMA2_SPORT0TX - 7) << DMA2_SPORT0TX_POS) | + ((CONFIG_DMA3_SPORT1RX - 7) << DMA3_SPORT1RX_POS) | + ((CONFIG_DMA4_SPORT1TX - 7) << DMA4_SPORT1TX_POS) | + ((CONFIG_DMA5_SPI - 7) << DMA5_SPI_POS) | + ((CONFIG_DMA6_UARTRX - 7) << DMA6_UARTRX_POS) | + ((CONFIG_DMA7_UARTTX - 7) << DMA7_UARTTX_POS)); + + bfin_write_SIC_IAR2(((CONFIG_TIMER0 - 7) << TIMER0_POS) | + ((CONFIG_TIMER1 - 7) << TIMER1_POS) | + ((CONFIG_TIMER2 - 7) << TIMER2_POS) | + ((CONFIG_PFA - 7) << PFA_POS) | + ((CONFIG_PFB - 7) << PFB_POS) | + ((CONFIG_MEMDMA0 - 7) << MEMDMA0_POS) | + ((CONFIG_MEMDMA1 - 7) << MEMDMA1_POS) | + ((CONFIG_WDTIMER - 7) << WDTIMER_POS)); + + SSYNC(); +} |
