diff options
Diffstat (limited to 'arch/arm/mach-sa1100/assabet.c')
| -rw-r--r-- | arch/arm/mach-sa1100/assabet.c | 54 |
1 files changed, 27 insertions, 27 deletions
diff --git a/arch/arm/mach-sa1100/assabet.c b/arch/arm/mach-sa1100/assabet.c index 65b0a9a3fb9c..c3f5064df4bf 100644 --- a/arch/arm/mach-sa1100/assabet.c +++ b/arch/arm/mach-sa1100/assabet.c @@ -42,13 +42,13 @@ #include "generic.h" #define ASSABET_BCR_DB1110 \ - (ASSABET_BCR_SPK_OFF | ASSABET_BCR_QMUTE | \ + (ASSABET_BCR_SPK_OFF | \ ASSABET_BCR_LED_GREEN | ASSABET_BCR_LED_RED | \ ASSABET_BCR_RS232EN | ASSABET_BCR_LCD_12RGB | \ ASSABET_BCR_IRDA_MD0) #define ASSABET_BCR_DB1111 \ - (ASSABET_BCR_SPK_OFF | ASSABET_BCR_QMUTE | \ + (ASSABET_BCR_SPK_OFF | \ ASSABET_BCR_LED_GREEN | ASSABET_BCR_LED_RED | \ ASSABET_BCR_RS232EN | ASSABET_BCR_LCD_12RGB | \ ASSABET_BCR_CF_BUS_OFF | ASSABET_BCR_STEREO_LB | \ @@ -127,15 +127,8 @@ static struct flash_platform_data assabet_flash_data = { }; static struct resource assabet_flash_resources[] = { - { - .start = SA1100_CS0_PHYS, - .end = SA1100_CS0_PHYS + SZ_32M - 1, - .flags = IORESOURCE_MEM, - }, { - .start = SA1100_CS1_PHYS, - .end = SA1100_CS1_PHYS + SZ_32M - 1, - .flags = IORESOURCE_MEM, - } + DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_32M), + DEFINE_RES_MEM(SA1100_CS1_PHYS, SZ_32M), }; @@ -272,13 +265,22 @@ static struct sa1100fb_mach_info pal_info = { }; #endif +#ifdef CONFIG_ASSABET_NEPONSET +static struct resource neponset_resources[] = { + DEFINE_RES_MEM(0x10000000, 0x08000000), + DEFINE_RES_MEM(0x18000000, 0x04000000), + DEFINE_RES_MEM(0x40000000, SZ_8K), + DEFINE_RES_IRQ(IRQ_GPIO25), +}; +#endif + static void __init assabet_init(void) { /* * Ensure that the power supply is in "high power" mode. */ - GPDR |= GPIO_GPIO16; GPSR = GPIO_GPIO16; + GPDR |= GPIO_GPIO16; /* * Ensure that these pins are set as outputs and are driving @@ -286,8 +288,16 @@ static void __init assabet_init(void) * the WS latch in the CPLD, and we don't float causing * excessive power drain. --rmk */ - GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM; GPCR = GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM; + GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM; + + /* + * Also set GPIO27 as an output; this is used to clock UART3 + * via the FPGA and as otherwise has no pullups or pulldowns, + * so stop it floating. + */ + GPCR = GPIO_GPIO27; + GPDR |= GPIO_GPIO27; /* * Set up registers for sleep mode. @@ -311,6 +321,9 @@ static void __init assabet_init(void) #ifndef CONFIG_ASSABET_NEPONSET printk( "Warning: Neponset detected but full support " "hasn't been configured in the kernel\n" ); +#else + platform_device_register_simple("neponset", 0, + neponset_resources, ARRAY_SIZE(neponset_resources)); #endif } @@ -482,21 +495,8 @@ static void __init assabet_map_io(void) */ Ser1SDCR0 |= SDCR0_SUS; - if (machine_has_neponset()) { -#ifdef CONFIG_ASSABET_NEPONSET - extern void neponset_map_io(void); - - /* - * We map Neponset registers even if it isn't present since - * many drivers will try to probe their stuff (and fail). - * This is still more friendly than a kernel paging request - * crash. - */ - neponset_map_io(); -#endif - } else { + if (!machine_has_neponset()) sa1100_register_uart_fns(&assabet_port_fns); - } /* * When Neponset is attached, the first UART should be |
