diff options
Diffstat (limited to 'arch/arm/mach-orion/ts209-setup.c')
-rw-r--r-- | arch/arm/mach-orion/ts209-setup.c | 305 |
1 files changed, 305 insertions, 0 deletions
diff --git a/arch/arm/mach-orion/ts209-setup.c b/arch/arm/mach-orion/ts209-setup.c new file mode 100644 index 000000000000..34f88ac24ac8 --- /dev/null +++ b/arch/arm/mach-orion/ts209-setup.c @@ -0,0 +1,305 @@ +/* + * QNAP TS-109/TS-209 Board Setup + * + * Maintainer: Byron Bradley <byron.bbradley@gmail.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/pci.h> +#include <linux/irq.h> +#include <linux/mtd/physmap.h> +#include <linux/mtd/nand.h> +#include <linux/mv643xx_eth.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> +#include <linux/i2c.h> +#include <asm/mach-types.h> +#include <asm/gpio.h> +#include <asm/mach/arch.h> +#include <asm/mach/pci.h> +#include <asm/arch/orion.h> +#include <asm/arch/platform.h> +#include "common.h" + +#define QNAP_TS209_NOR_BOOT_BASE 0xf4000000 +#define QNAP_TS209_NOR_BOOT_SIZE SZ_8M + +/**************************************************************************** + * 8MiB NOR flash. The struct mtd_partition is not in the same order as the + * partitions on the device because we want to keep compatability with + * existing QNAP firmware. + * + * Layout as used by QNAP: + * [2] 0x00000000-0x00200000 : "Kernel" + * [3] 0x00200000-0x00600000 : "RootFS1" + * [4] 0x00600000-0x00700000 : "RootFS2" + * [6] 0x00700000-0x00760000 : "NAS Config" (read-only) + * [5] 0x00760000-0x00780000 : "U-Boot Config" + * [1] 0x00780000-0x00800000 : "U-Boot" (read-only) + ***************************************************************************/ +static struct mtd_partition qnap_ts209_partitions[] = { + { + .name = "U-Boot", + .size = 0x00080000, + .offset = 0x00780000, + .mask_flags = MTD_WRITEABLE, + }, { + .name = "Kernel", + .size = 0x00200000, + .offset = 0, + }, { + .name = "RootFS1", + .size = 0x00400000, + .offset = 0x00200000, + }, { + .name = "RootFS2", + .size = 0x00100000, + .offset = 0x00600000, + }, { + .name = "U-Boot Config", + .size = 0x00020000, + .offset = 0x00760000, + }, { + .name = "NAS Config", + .size = 0x00060000, + .offset = 0x00700000, + .mask_flags = MTD_WRITEABLE, + } +}; + +static struct physmap_flash_data qnap_ts209_nor_flash_data = { + .width = 1, + .parts = qnap_ts209_partitions, + .nr_parts = ARRAY_SIZE(qnap_ts209_partitions) +}; + +static struct resource qnap_ts209_nor_flash_resource = { + .flags = IORESOURCE_MEM, + .start = QNAP_TS209_NOR_BOOT_BASE, + .end = QNAP_TS209_NOR_BOOT_BASE + QNAP_TS209_NOR_BOOT_SIZE - 1, +}; + +static struct platform_device qnap_ts209_nor_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { .platform_data = &qnap_ts209_nor_flash_data, }, + .resource = &qnap_ts209_nor_flash_resource, + .num_resources = 1, +}; + +/***************************************************************************** + * PCI + ****************************************************************************/ + +#define QNAP_TS209_PCI_SLOT0_OFFS 7 +#define QNAP_TS209_PCI_SLOT0_IRQ_PIN 6 +#define QNAP_TS209_PCI_SLOT1_IRQ_PIN 7 + +void __init qnap_ts209_pci_preinit(void) +{ + int pin; + + /* + * Configure PCI GPIO IRQ pins + */ + pin = QNAP_TS209_PCI_SLOT0_IRQ_PIN; + if (gpio_request(pin, "PCI Int1") == 0) { + if (gpio_direction_input(pin) == 0) { + set_irq_type(gpio_to_irq(pin), IRQT_LOW); + } else { + printk(KERN_ERR "qnap_ts209_pci_preinit failed to " + "set_irq_type pin %d\n", pin); + gpio_free(pin); + } + } else { + printk(KERN_ERR "qnap_ts209_pci_preinit failed to gpio_request " + "%d\n", pin); + } + + pin = QNAP_TS209_PCI_SLOT1_IRQ_PIN; + if (gpio_request(pin, "PCI Int2") == 0) { + if (gpio_direction_input(pin) == 0) { + set_irq_type(gpio_to_irq(pin), IRQT_LOW); + } else { + printk(KERN_ERR "qnap_ts209_pci_preinit failed " + "to set_irq_type pin %d\n", pin); + gpio_free(pin); + } + } else { + printk(KERN_ERR "qnap_ts209_pci_preinit failed to gpio_request " + "%d\n", pin); + } +} + +static int __init qnap_ts209_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + /* + * PCIE IRQ is connected internally (not GPIO) + */ + if (dev->bus->number == orion_pcie_local_bus_nr()) + return IRQ_ORION_PCIE0_INT; + + /* + * PCI IRQs are connected via GPIOs + */ + switch (slot - QNAP_TS209_PCI_SLOT0_OFFS) { + case 0: + return gpio_to_irq(QNAP_TS209_PCI_SLOT0_IRQ_PIN); + case 1: + return gpio_to_irq(QNAP_TS209_PCI_SLOT1_IRQ_PIN); + default: + return -1; + } +} + +static struct hw_pci qnap_ts209_pci __initdata = { + .nr_controllers = 2, + .preinit = qnap_ts209_pci_preinit, + .swizzle = pci_std_swizzle, + .setup = orion_pci_sys_setup, + .scan = orion_pci_sys_scan_bus, + .map_irq = qnap_ts209_pci_map_irq, +}; + +static int __init qnap_ts209_pci_init(void) +{ + if (machine_is_ts_x09()) + pci_common_init(&qnap_ts209_pci); + + return 0; +} + +subsys_initcall(qnap_ts209_pci_init); + +/***************************************************************************** + * Ethernet + ****************************************************************************/ + +static struct mv643xx_eth_platform_data qnap_ts209_eth_data = { + .phy_addr = 8, + .force_phy_addr = 1, +}; + +/***************************************************************************** + * RTC S35390A on I2C bus + ****************************************************************************/ +static struct i2c_board_info __initdata qnap_ts209_i2c_rtc = { + .driver_name = "rtc-s35390a", + .addr = 0x30, +}; + +/**************************************************************************** + * GPIO Attached Keys + * Power button is attached to the PIC microcontroller + ****************************************************************************/ + +#define QNAP_TS209_GPIO_KEY_MEDIA 1 +#define QNAP_TS209_GPIO_KEY_RESET 2 + +static struct gpio_keys_button qnap_ts209_buttons[] = { + { + .code = KEY_RESTART, + .gpio = QNAP_TS209_GPIO_KEY_MEDIA, + .desc = "USB Copy Button", + .active_low = 1, + }, + { + .code = KEY_POWER, + .gpio = QNAP_TS209_GPIO_KEY_RESET, + .desc = "Reset Button", + .active_low = 1, + } +}; + +static struct gpio_keys_platform_data qnap_ts209_button_data = { + .buttons = qnap_ts209_buttons, + .nbuttons = ARRAY_SIZE(qnap_ts209_buttons), +}; + +static struct platform_device qnap_ts209_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { .platform_data = &qnap_ts209_button_data, }, +}; + +/***************************************************************************** + * General Setup + ****************************************************************************/ + +static struct platform_device *qnap_ts209_devices[] __initdata = { + &qnap_ts209_nor_flash, + &qnap_ts209_button_device, +}; + +static void __init qnap_ts209_init(void) +{ + /* + * Setup basic Orion functions. Need to be called early. + */ + orion_init(); + + /* + * Setup flash mapping + */ + orion_setup_cpu_win(ORION_DEV_BOOT, QNAP_TS209_NOR_BOOT_BASE, + QNAP_TS209_NOR_BOOT_SIZE, -1); + + /* + * Open a special address decode windows for the PCIE WA. + */ + orion_write(ORION_REGS_BASE | 0x20074, ORION_PCIE_WA_BASE); + orion_write(ORION_REGS_BASE | 0x20070, (0x7941 | + (((ORION_PCIE_WA_SIZE >> 16) - 1)) << 16)); + + /* + * Setup Multiplexing Pins -- + * MPP[0] Reserved + * MPP[1] USB copy button (0 active) + * MPP[2] Load defaults button (0 active) + * MPP[3] GPIO RTC + * MPP[4-5] Reserved + * MPP[6] PCI Int A + * MPP[7] PCI Int B + * MPP[8-11] Reserved + * MPP[12] SATA 0 presence + * MPP[13] SATA 1 presence + * MPP[14] SATA 0 active + * MPP[15] SATA 1 active + * MPP[16] UART1 RXD + * MPP[17] UART1 TXD + * MPP[18] SW_RST (0 active) + * MPP[19] Reserved + * MPP[20] PCI clock 0 + * MPP[21] PCI clock 1 + * MPP[22] USB 0 over current + * MPP[23-25] Reserved + */ + orion_write(MPP_0_7_CTRL, 0x3); + orion_write(MPP_8_15_CTRL, 0x55550000); + orion_write(MPP_16_19_CTRL, 0x5500); + orion_gpio_set_valid_pins(0x3cc0fff); + + platform_add_devices(qnap_ts209_devices, + ARRAY_SIZE(qnap_ts209_devices)); + i2c_register_board_info(0, &qnap_ts209_i2c_rtc, 1); + orion_eth_init(&qnap_ts209_eth_data); +} + +MACHINE_START(TS209, "QNAP TS-109/TS-209") + /* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */ + .phys_io = ORION_REGS_BASE, + .io_pg_offst = ((ORION_REGS_BASE) >> 18) & 0xFFFC, + .boot_params = 0x00000100, + .init_machine = qnap_ts209_init, + .map_io = orion_map_io, + .init_irq = orion_init_irq, + .timer = &orion_timer, +MACHINE_END |