diff options
Diffstat (limited to 'arch/arm/mach-at91rm9200/board-sam9261ek.c')
| -rw-r--r-- | arch/arm/mach-at91rm9200/board-sam9261ek.c | 259 |
1 files changed, 259 insertions, 0 deletions
diff --git a/arch/arm/mach-at91rm9200/board-sam9261ek.c b/arch/arm/mach-at91rm9200/board-sam9261ek.c new file mode 100644 index 000000000000..30b490d8886b --- /dev/null +++ b/arch/arm/mach-at91rm9200/board-sam9261ek.c @@ -0,0 +1,259 @@ +/* + * linux/arch/arm/mach-at91rm9200/board-ek.c + * + * Copyright (C) 2005 SAN People + * Copyright (C) 2006 Atmel + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/mm.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/spi/spi.h> +#include <linux/dm9000.h> + +#include <asm/hardware.h> +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/irq.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/arch/board.h> +#include <asm/arch/gpio.h> +#include <asm/arch/at91sam926x_mc.h> + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 2 = USART0 .. USART2 + * 3 = DBGU + */ +static struct at91_uart_config __initdata ek_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 1, + .tty_map = { 3, -1, -1, -1 } /* ttyS0, ..., ttyS3 */ +}; + +static void __init ek_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91sam9261_initialize(18432000); + + /* Setup the serial ports and console */ + at91_init_serial(&ek_uart_config); +} + +static void __init ek_init_irq(void) +{ + at91sam9261_init_interrupts(NULL); +} + + +/* + * DM9000 ethernet device + */ +#if defined(CONFIG_DM9000) +static struct resource at91sam9261_dm9000_resource[] = { + [0] = { + .start = AT91_CHIPSELECT_2, + .end = AT91_CHIPSELECT_2 + 3, + .flags = IORESOURCE_MEM + }, + [1] = { + .start = AT91_CHIPSELECT_2 + 0x44, + .end = AT91_CHIPSELECT_2 + 0xFF, + .flags = IORESOURCE_MEM + }, + [2] = { + .start = AT91_PIN_PC11, + .end = AT91_PIN_PC11, + .flags = IORESOURCE_IRQ + } +}; + +static struct dm9000_plat_data dm9000_platdata = { + .flags = DM9000_PLATF_16BITONLY, +}; + +static struct platform_device at91sam9261_dm9000_device = { + .name = "dm9000", + .id = 0, + .num_resources = ARRAY_SIZE(at91sam9261_dm9000_resource), + .resource = at91sam9261_dm9000_resource, + .dev = { + .platform_data = &dm9000_platdata, + } +}; + +static void __init ek_add_device_dm9000(void) +{ + /* + * Configure Chip-Select 2 on SMC for the DM9000. + * Note: These timings were calculated for MASTER_CLOCK = 100000000 + * according to the DM9000 timings. + */ + at91_sys_write(AT91_SMC_SETUP(2), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0)); + at91_sys_write(AT91_SMC_PULSE(2), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(8) | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(8)); + at91_sys_write(AT91_SMC_CYCLE(2), AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16)); + at91_sys_write(AT91_SMC_MODE(2), AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 | AT91_SMC_TDF_(1)); + + /* Configure Reset signal as output */ + at91_set_gpio_output(AT91_PIN_PC10, 0); + + /* Configure Interrupt pin as input, no pull-up */ + at91_set_gpio_input(AT91_PIN_PC11, 0); + + platform_device_register(&at91sam9261_dm9000_device); +} +#else +static void __init ek_add_device_dm9000(void) {} +#endif /* CONFIG_DM9000 */ + + +/* + * USB Host Port + */ +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, +}; + + +/* + * USB Device Port + */ +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PB29, + .pullup_pin = 0, /* pull-up driven by UDC */ +}; + + +/* + * MCI (SD/MMC) + */ +static struct at91_mmc_data __initdata ek_mmc_data = { + .wire4 = 1, +// .det_pin = ... not connected +// .wp_pin = ... not connected +// .vcc_pin = ... not connected +}; + + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Partition 1", + .offset = 0, + .size = 256 * 1024, + }, + { + .name = "Partition 2", + .offset = 256 * 1024 , + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct mtd_partition *nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(ek_nand_partition); + return ek_nand_partition; +} + +static struct at91_nand_data __initdata ek_nand_data = { + .ale = 22, + .cle = 21, +// .det_pin = ... not connected + .rdy_pin = AT91_PIN_PC15, + .enable_pin = AT91_PIN_PC14, + .partition_info = nand_partitions, +#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) + .bus_width_16 = 1, +#else + .bus_width_16 = 0, +#endif +}; + +/* + * SPI devices + */ +static struct spi_board_info ek_spi_devices[] = { + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) + { /* DataFlash card - jumper (J12) configurable to CS3 or CS0 */ + .modalias = "mtd_dataflash", + .chip_select = 3, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#elif defined(CONFIG_SND_AT73C213) + { /* AT73C213 DAC */ + .modalias = "snd_at73c213", + .chip_select = 3, + .max_speed_hz = 10 * 1000 * 1000, + .bus_num = 0, + }, +#endif +}; + + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + /* I2C */ + at91_add_device_i2c(); + /* NAND */ + at91_add_device_nand(&ek_nand_data); + /* DM9000 ethernet */ + ek_add_device_dm9000(); + + /* spi0 and mmc/sd share the same PIO pins */ +#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); +#else + /* MMC */ + at91_add_device_mmc(&ek_mmc_data); +#endif +} + +MACHINE_START(AT91SAM9261EK, "Atmel AT91SAM9261-EK") + /* Maintainer: Atmel */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END |
