diff options
Diffstat (limited to 'arch/arm/mach-at91/board-rsi-ews.c')
| -rw-r--r-- | arch/arm/mach-at91/board-rsi-ews.c | 232 |
1 files changed, 0 insertions, 232 deletions
diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c deleted file mode 100644 index f28e8b74df4b..000000000000 --- a/arch/arm/mach-at91/board-rsi-ews.c +++ /dev/null @@ -1,232 +0,0 @@ -/* - * board-rsi-ews.c - * - * Copyright (C) - * 2005 SAN People, - * 2008-2011 R-S-I Elektrotechnik GmbH & Co. KG - * - * Licensed under GPLv2 or later. - */ - -#include <linux/types.h> -#include <linux/init.h> -#include <linux/mm.h> -#include <linux/module.h> -#include <linux/platform_device.h> -#include <linux/spi/spi.h> -#include <linux/mtd/physmap.h> - -#include <asm/setup.h> -#include <asm/mach-types.h> -#include <asm/irq.h> - -#include <asm/mach/arch.h> -#include <asm/mach/map.h> -#include <asm/mach/irq.h> - -#include <mach/hardware.h> - -#include <linux/gpio.h> - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - -static void __init rsi_ews_init_early(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91_initialize(18432000); -} - -/* - * Ethernet - */ -static struct macb_platform_data rsi_ews_eth_data __initdata = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 1, -}; - -/* - * USB Host - */ -static struct at91_usbh_data rsi_ews_usbh_data __initdata = { - .ports = 1, - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -/* - * SD/MC - */ -static struct mci_platform_data __initdata rsi_ews_mci0_data = { - .slot[0] = { - .bus_width = 4, - .detect_pin = AT91_PIN_PB27, - .wp_pin = AT91_PIN_PB29, - }, -}; - -/* - * I2C - */ -static struct i2c_board_info rsi_ews_i2c_devices[] __initdata = { - { - I2C_BOARD_INFO("ds1337", 0x68), - }, - { - I2C_BOARD_INFO("24c01", 0x50), - } -}; - -/* - * LEDs - */ -static struct gpio_led rsi_ews_leds[] = { - { - .name = "led0", - .gpio = AT91_PIN_PB6, - .active_low = 0, - }, - { - .name = "led1", - .gpio = AT91_PIN_PB7, - .active_low = 0, - }, - { - .name = "led2", - .gpio = AT91_PIN_PB8, - .active_low = 0, - }, - { - .name = "led3", - .gpio = AT91_PIN_PB9, - .active_low = 0, - }, -}; - -/* - * DataFlash - */ -static struct spi_board_info rsi_ews_spi_devices[] = { - { /* DataFlash chip 1*/ - .modalias = "mtd_dataflash", - .chip_select = 0, - .max_speed_hz = 5 * 1000 * 1000, - }, - { /* DataFlash chip 2*/ - .modalias = "mtd_dataflash", - .chip_select = 1, - .max_speed_hz = 5 * 1000 * 1000, - }, -}; - -/* - * NOR flash - */ -static struct mtd_partition rsiews_nor_partitions[] = { - { - .name = "boot", - .offset = 0, - .size = 3 * SZ_128K, - .mask_flags = MTD_WRITEABLE - }, - { - .name = "kernel", - .offset = MTDPART_OFS_NXTBLK, - .size = SZ_2M - (3 * SZ_128K) - }, - { - .name = "root", - .offset = MTDPART_OFS_NXTBLK, - .size = SZ_8M - }, - { - .name = "kernelupd", - .offset = MTDPART_OFS_NXTBLK, - .size = 3 * SZ_512K, - .mask_flags = MTD_WRITEABLE - }, - { - .name = "rootupd", - .offset = MTDPART_OFS_NXTBLK, - .size = 9 * SZ_512K, - .mask_flags = MTD_WRITEABLE - }, -}; - -static struct physmap_flash_data rsiews_nor_data = { - .width = 2, - .parts = rsiews_nor_partitions, - .nr_parts = ARRAY_SIZE(rsiews_nor_partitions), -}; - -#define NOR_BASE AT91_CHIPSELECT_0 -#define NOR_SIZE SZ_16M - -static struct resource nor_flash_resources[] = { - { - .start = NOR_BASE, - .end = NOR_BASE + NOR_SIZE - 1, - .flags = IORESOURCE_MEM, - } -}; - -static struct platform_device rsiews_nor_flash = { - .name = "physmap-flash", - .id = 0, - .dev = { - .platform_data = &rsiews_nor_data, - }, - .resource = nor_flash_resources, - .num_resources = ARRAY_SIZE(nor_flash_resources), -}; - -/* - * Init Func - */ -static void __init rsi_ews_board_init(void) -{ - /* Serial */ - /* DBGU on ttyS0. (Rx & Tx only) */ - /* This one is for debugging */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - /* Dialin/-out modem interface */ - at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART3 on ttyS4. (Rx, Tx, RTS) */ - /* RS485 communication */ - at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS); - at91_add_device_serial(); - at91_set_gpio_output(AT91_PIN_PA21, 0); - /* Ethernet */ - at91_add_device_eth(&rsi_ews_eth_data); - /* USB Host */ - at91_add_device_usbh(&rsi_ews_usbh_data); - /* I2C */ - at91_add_device_i2c(rsi_ews_i2c_devices, - ARRAY_SIZE(rsi_ews_i2c_devices)); - /* SPI */ - at91_add_device_spi(rsi_ews_spi_devices, - ARRAY_SIZE(rsi_ews_spi_devices)); - /* MMC */ - at91_add_device_mci(0, &rsi_ews_mci0_data); - /* NOR Flash */ - platform_device_register(&rsiews_nor_flash); - /* LEDs */ - at91_gpio_leds(rsi_ews_leds, ARRAY_SIZE(rsi_ews_leds)); -} - -MACHINE_START(RSI_EWS, "RSI EWS") - /* Maintainer: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de> */ - .init_time = at91rm9200_timer_init, - .map_io = at91_map_io, - .handle_irq = at91_aic_handle_irq, - .init_early = rsi_ews_init_early, - .init_irq = at91_init_irq_default, - .init_machine = rsi_ews_board_init, -MACHINE_END |
