diff options
Diffstat (limited to 'arch/arm/mach-at91/board-cap9adk.c')
| -rw-r--r-- | arch/arm/mach-at91/board-cap9adk.c | 396 |
1 files changed, 0 insertions, 396 deletions
diff --git a/arch/arm/mach-at91/board-cap9adk.c b/arch/arm/mach-at91/board-cap9adk.c deleted file mode 100644 index ac3de4f7c31d..000000000000 --- a/arch/arm/mach-at91/board-cap9adk.c +++ /dev/null @@ -1,396 +0,0 @@ -/* - * linux/arch/arm/mach-at91/board-cap9adk.c - * - * Copyright (C) 2007 Stelian Pop <stelian.pop@leadtechdesign.com> - * Copyright (C) 2007 Lead Tech Design <www.leadtechdesign.com> - * Copyright (C) 2005 SAN People - * Copyright (C) 2007 Atmel Corporation. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include <linux/types.h> -#include <linux/gpio.h> -#include <linux/init.h> -#include <linux/mm.h> -#include <linux/module.h> -#include <linux/platform_device.h> -#include <linux/spi/spi.h> -#include <linux/spi/ads7846.h> -#include <linux/fb.h> -#include <linux/mtd/physmap.h> - -#include <video/atmel_lcdc.h> - -#include <mach/hardware.h> -#include <asm/setup.h> -#include <asm/mach-types.h> - -#include <asm/mach/arch.h> -#include <asm/mach/map.h> - -#include <mach/board.h> -#include <mach/at91cap9_matrix.h> -#include <mach/at91sam9_smc.h> -#include <mach/system_rev.h> - -#include "sam9_smc.h" -#include "generic.h" - - -static void __init cap9adk_init_early(void) -{ - /* Initialize processor: 12 MHz crystal */ - at91_initialize(12000000); - - /* Setup the LEDs: USER1 and USER2 LED for cpu/timer... */ - at91_init_leds(AT91_PIN_PA10, AT91_PIN_PA11); - /* ... POWER LED always on */ - at91_set_gpio_output(AT91_PIN_PC29, 1); - - /* Setup the serial ports and console */ - at91_register_uart(0, 0, 0); /* DBGU = ttyS0 */ - at91_set_serial_console(0); -} - -/* - * USB Host port - */ -static struct at91_usbh_data __initdata cap9adk_usbh_data = { - .ports = 2, - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -/* - * USB HS Device port - */ -static struct usba_platform_data __initdata cap9adk_usba_udc_data = { - .vbus_pin = AT91_PIN_PB31, -}; - -/* - * ADS7846 Touchscreen - */ -#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) -static int ads7843_pendown_state(void) -{ - return !at91_get_gpio_value(AT91_PIN_PC4); /* Touchscreen PENIRQ */ -} - -static struct ads7846_platform_data ads_info = { - .model = 7843, - .x_min = 150, - .x_max = 3830, - .y_min = 190, - .y_max = 3830, - .vref_delay_usecs = 100, - .x_plate_ohms = 450, - .y_plate_ohms = 250, - .pressure_max = 15000, - .debounce_max = 1, - .debounce_rep = 0, - .debounce_tol = (~0), - .get_pendown_state = ads7843_pendown_state, -}; - -static void __init cap9adk_add_device_ts(void) -{ - at91_set_gpio_input(AT91_PIN_PC4, 1); /* Touchscreen PENIRQ */ - at91_set_gpio_input(AT91_PIN_PC5, 1); /* Touchscreen BUSY */ -} -#else -static void __init cap9adk_add_device_ts(void) {} -#endif - - -/* - * SPI devices. - */ -static struct spi_board_info cap9adk_spi_devices[] = { -#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) - { /* DataFlash card */ - .modalias = "mtd_dataflash", - .chip_select = 0, - .max_speed_hz = 15 * 1000 * 1000, - .bus_num = 0, - }, -#endif -#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) - { - .modalias = "ads7846", - .chip_select = 3, /* can be 2 or 3, depending on J2 jumper */ - .max_speed_hz = 125000 * 26, /* (max sample rate @ 3V) * (cmd + data + overhead) */ - .bus_num = 0, - .platform_data = &ads_info, - .irq = AT91_PIN_PC4, - }, -#endif -}; - - -/* - * MCI (SD/MMC) - */ -static struct at91_mmc_data __initdata cap9adk_mmc_data = { - .wire4 = 1, - .det_pin = -EINVAL, - .wp_pin = -EINVAL, - .vcc_pin = -EINVAL, -}; - - -/* - * MACB Ethernet device - */ -static struct macb_platform_data __initdata cap9adk_macb_data = { - .phy_irq_pin = -EINVAL, - .is_rmii = 1, -}; - - -/* - * NAND flash - */ -static struct mtd_partition __initdata cap9adk_nand_partitions[] = { - { - .name = "NAND partition", - .offset = 0, - .size = MTDPART_SIZ_FULL, - }, -}; - -static struct atmel_nand_data __initdata cap9adk_nand_data = { - .ale = 21, - .cle = 22, - .det_pin = -EINVAL, - .rdy_pin = -EINVAL, - .enable_pin = AT91_PIN_PD15, - .parts = cap9adk_nand_partitions, - .num_parts = ARRAY_SIZE(cap9adk_nand_partitions), -}; - -static struct sam9_smc_config __initdata cap9adk_nand_smc_config = { - .ncs_read_setup = 1, - .nrd_setup = 2, - .ncs_write_setup = 1, - .nwe_setup = 2, - - .ncs_read_pulse = 6, - .nrd_pulse = 4, - .ncs_write_pulse = 6, - .nwe_pulse = 4, - - .read_cycle = 8, - .write_cycle = 8, - - .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE, - .tdf_cycles = 1, -}; - -static void __init cap9adk_add_device_nand(void) -{ - unsigned long csa; - - csa = at91_sys_read(AT91_MATRIX_EBICSA); - at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_VDDIOMSEL_3_3V); - - cap9adk_nand_data.bus_width_16 = board_have_nand_16bit(); - /* setup bus-width (8 or 16) */ - if (cap9adk_nand_data.bus_width_16) - cap9adk_nand_smc_config.mode |= AT91_SMC_DBW_16; - else - cap9adk_nand_smc_config.mode |= AT91_SMC_DBW_8; - - /* configure chip-select 3 (NAND) */ - sam9_smc_configure(0, 3, &cap9adk_nand_smc_config); - - at91_add_device_nand(&cap9adk_nand_data); -} - - -/* - * NOR flash - */ -static struct mtd_partition cap9adk_nor_partitions[] = { - { - .name = "NOR partition", - .offset = 0, - .size = MTDPART_SIZ_FULL, - }, -}; - -static struct physmap_flash_data cap9adk_nor_data = { - .width = 2, - .parts = cap9adk_nor_partitions, - .nr_parts = ARRAY_SIZE(cap9adk_nor_partitions), -}; - -#define NOR_BASE AT91_CHIPSELECT_0 -#define NOR_SIZE SZ_8M - -static struct resource nor_flash_resources[] = { - { - .start = NOR_BASE, - .end = NOR_BASE + NOR_SIZE - 1, - .flags = IORESOURCE_MEM, - } -}; - -static struct platform_device cap9adk_nor_flash = { - .name = "physmap-flash", - .id = 0, - .dev = { - .platform_data = &cap9adk_nor_data, - }, - .resource = nor_flash_resources, - .num_resources = ARRAY_SIZE(nor_flash_resources), -}; - -static struct sam9_smc_config __initdata cap9adk_nor_smc_config = { - .ncs_read_setup = 2, - .nrd_setup = 4, - .ncs_write_setup = 2, - .nwe_setup = 4, - - .ncs_read_pulse = 10, - .nrd_pulse = 8, - .ncs_write_pulse = 10, - .nwe_pulse = 8, - - .read_cycle = 16, - .write_cycle = 16, - - .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16, - .tdf_cycles = 1, -}; - -static __init void cap9adk_add_device_nor(void) -{ - unsigned long csa; - - csa = at91_sys_read(AT91_MATRIX_EBICSA); - at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_VDDIOMSEL_3_3V); - - /* configure chip-select 0 (NOR) */ - sam9_smc_configure(0, 0, &cap9adk_nor_smc_config); - - platform_device_register(&cap9adk_nor_flash); -} - - -/* - * LCD Controller - */ -#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE) -static struct fb_videomode at91_tft_vga_modes[] = { - { - .name = "TX09D50VM1CCA @ 60", - .refresh = 60, - .xres = 240, .yres = 320, - .pixclock = KHZ2PICOS(4965), - - .left_margin = 1, .right_margin = 33, - .upper_margin = 1, .lower_margin = 0, - .hsync_len = 5, .vsync_len = 1, - - .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, - .vmode = FB_VMODE_NONINTERLACED, - }, -}; - -static struct fb_monspecs at91fb_default_monspecs = { - .manufacturer = "HIT", - .monitor = "TX09D70VM1CCA", - - .modedb = at91_tft_vga_modes, - .modedb_len = ARRAY_SIZE(at91_tft_vga_modes), - .hfmin = 15000, - .hfmax = 64000, - .vfmin = 50, - .vfmax = 150, -}; - -#define AT91CAP9_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \ - | ATMEL_LCDC_DISTYPE_TFT \ - | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE) - -static void at91_lcdc_power_control(int on) -{ - if (on) - at91_set_gpio_value(AT91_PIN_PC0, 0); /* power up */ - else - at91_set_gpio_value(AT91_PIN_PC0, 1); /* power down */ -} - -/* Driver datas */ -static struct atmel_lcdfb_info __initdata cap9adk_lcdc_data = { - .default_bpp = 16, - .default_dmacon = ATMEL_LCDC_DMAEN, - .default_lcdcon2 = AT91CAP9_DEFAULT_LCDCON2, - .default_monspecs = &at91fb_default_monspecs, - .atmel_lcdfb_power_control = at91_lcdc_power_control, - .guard_time = 1, -}; - -#else -static struct atmel_lcdfb_info __initdata cap9adk_lcdc_data; -#endif - - -/* - * AC97 - */ -static struct ac97c_platform_data cap9adk_ac97_data = { - .reset_pin = -EINVAL, -}; - - -static void __init cap9adk_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* USB Host */ - at91_add_device_usbh(&cap9adk_usbh_data); - /* USB HS */ - at91_add_device_usba(&cap9adk_usba_udc_data); - /* SPI */ - at91_add_device_spi(cap9adk_spi_devices, ARRAY_SIZE(cap9adk_spi_devices)); - /* Touchscreen */ - cap9adk_add_device_ts(); - /* MMC */ - at91_add_device_mmc(1, &cap9adk_mmc_data); - /* Ethernet */ - at91_add_device_eth(&cap9adk_macb_data); - /* NAND */ - cap9adk_add_device_nand(); - /* NOR Flash */ - cap9adk_add_device_nor(); - /* I2C */ - at91_add_device_i2c(NULL, 0); - /* LCD Controller */ - at91_add_device_lcdc(&cap9adk_lcdc_data); - /* AC97 */ - at91_add_device_ac97(&cap9adk_ac97_data); -} - -MACHINE_START(AT91CAP9ADK, "Atmel AT91CAP9A-DK") - /* Maintainer: Stelian Pop <stelian.pop@leadtechdesign.com> */ - .timer = &at91sam926x_timer, - .map_io = at91_map_io, - .init_early = cap9adk_init_early, - .init_irq = at91_init_irq_default, - .init_machine = cap9adk_board_init, -MACHINE_END |
