diff options
Diffstat (limited to 'arch/arm/boot')
35 files changed, 1434 insertions, 155 deletions
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index bbe7a45b0b8e..fcce17c14bc2 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -199,6 +199,10 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \ omap2420-n810-wimax.dtb \ omap3430-sdp.dtb \ omap3-beagle.dtb \ + omap3-cm-t3517.dtb \ + omap3-sbc-t3517.dtb \ + omap3-cm-t3530.dtb \ + omap3-sbc-t3530.dtb \ omap3-cm-t3730.dtb \ omap3-sbc-t3730.dtb \ omap3-devkit8000.dtb \ @@ -213,6 +217,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \ omap3-gta04.dtb \ omap3-igep0020.dtb \ omap3-igep0030.dtb \ + omap3-lilly-dbb056.dtb \ omap3-zoom3.dtb \ omap4-panda.dtb \ omap4-panda-a4.dtb \ diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts index 7e6c64ed966d..07d61bb8d481 100644 --- a/arch/arm/boot/dts/am335x-evm.dts +++ b/arch/arm/boot/dts/am335x-evm.dts @@ -434,9 +434,9 @@ ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ nand@0,0 { reg = <0 0 0>; /* CS0, offset 0 */ - nand-bus-width = <8>; ti,nand-ecc-opt = "bch8"; - gpmc,device-nand = "true"; + ti,elm-id = <&elm>; + nand-bus-width = <8>; gpmc,device-width = <1>; gpmc,sync-clk-ps = <0>; gpmc,cs-on-ns = <0>; @@ -460,50 +460,51 @@ gpmc,wait-monitoring-ns = <0>; gpmc,wr-access-ns = <40>; gpmc,wr-data-mux-bus-ns = <0>; - + /* MTD partition table */ + /* All SPL-* partitions are sized to minimal length + * which can be independently programmable. For + * NAND flash this is equal to size of erase-block */ #address-cells = <1>; #size-cells = <1>; - elm_id = <&elm>; - - /* MTD partition table */ partition@0 { - label = "SPL1"; + label = "NAND.SPL"; reg = <0x00000000 0x000020000>; }; - partition@1 { - label = "SPL2"; + label = "NAND.SPL.backup1"; reg = <0x00020000 0x00020000>; }; - partition@2 { - label = "SPL3"; + label = "NAND.SPL.backup2"; reg = <0x00040000 0x00020000>; }; - partition@3 { - label = "SPL4"; + label = "NAND.SPL.backup3"; reg = <0x00060000 0x00020000>; }; - partition@4 { - label = "U-boot"; - reg = <0x00080000 0x001e0000>; + label = "NAND.u-boot-spl"; + reg = <0x00080000 0x00040000>; }; - partition@5 { - label = "environment"; - reg = <0x00260000 0x00020000>; + label = "NAND.u-boot"; + reg = <0x000C0000 0x00100000>; }; - partition@6 { - label = "Kernel"; - reg = <0x00280000 0x00500000>; + label = "NAND.u-boot-env"; + reg = <0x001C0000 0x00020000>; }; - partition@7 { - label = "File-System"; - reg = <0x00780000 0x0F880000>; + label = "NAND.u-boot-env.backup1"; + reg = <0x001E0000 0x00020000>; + }; + partition@8 { + label = "NAND.kernel"; + reg = <0x00200000 0x00800000>; + }; + partition@9 { + label = "NAND.file-system"; + reg = <0x00A00000 0x0F600000>; }; }; }; diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts index 4718ec4a4dbf..413e5e133b3e 100644 --- a/arch/arm/boot/dts/am335x-evmsk.dts +++ b/arch/arm/boot/dts/am335x-evmsk.dts @@ -121,7 +121,7 @@ ti,model = "AM335x-EVMSK"; ti,audio-codec = <&tlv320aic3106>; ti,mcasp-controller = <&mcasp1>; - ti,codec-clock-rate = <24576000>; + ti,codec-clock-rate = <24000000>; ti,audio-routing = "Headphone Jack", "HPLOUT", "Headphone Jack", "HPROUT"; @@ -336,9 +336,18 @@ status = "okay"; }; + usb-phy@47401b00 { + status = "okay"; + }; + usb@47401000 { status = "okay"; }; + + usb@47401800 { + status = "okay"; + dr_mode = "host"; + }; }; &epwmss2 { diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index 6d95d3df33c7..707342914a6f 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -58,6 +58,10 @@ 275000 1125000 >; voltage-tolerance = <2>; /* 2 percentage */ + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + clock-latency = <300000>; /* From omap-cpufreq driver */ }; }; @@ -318,6 +322,7 @@ compatible = "ti,omap4-hwspinlock"; reg = <0x480ca000 0x1000>; ti,hwmods = "spinlock"; + #hwlock-cells = <1>; }; wdt2: wdt@44e35000 { @@ -399,7 +404,7 @@ ti,timer-pwm; }; - rtc@44e3e000 { + rtc: rtc@44e3e000 { compatible = "ti,da830-rtc"; reg = <0x44e3e000 0x1000>; interrupts = <75 @@ -582,6 +587,8 @@ compatible = "ti,am33xx-ecap"; #pwm-cells = <3>; reg = <0x48300100 0x80>; + interrupts = <31>; + interrupt-names = "ecap0"; ti,hwmods = "ecap0"; status = "disabled"; }; @@ -610,6 +617,8 @@ compatible = "ti,am33xx-ecap"; #pwm-cells = <3>; reg = <0x48302100 0x80>; + interrupts = <47>; + interrupt-names = "ecap1"; ti,hwmods = "ecap1"; status = "disabled"; }; @@ -638,6 +647,8 @@ compatible = "ti,am33xx-ecap"; #pwm-cells = <3>; reg = <0x48304100 0x80>; + interrupts = <61>; + interrupt-names = "ecap2"; ti,hwmods = "ecap2"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index 5a7cc38157b0..b687869b8298 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -33,6 +33,11 @@ compatible = "arm,cortex-a9"; device_type = "cpu"; reg = <0>; + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ }; }; @@ -351,6 +356,13 @@ status = "disabled"; }; + hwspinlock: spinlock@480ca000 { + compatible = "ti,omap4-hwspinlock"; + reg = <0x480ca000 0x1000>; + ti,hwmods = "spinlock"; + #hwlock-cells = <1>; + }; + i2c0: i2c@44e0b000 { compatible = "ti,am4372-i2c","ti,omap4-i2c"; reg = <0x44e0b000 0x1000>; @@ -698,6 +710,30 @@ <&edma 11>; dma-names = "tx", "rx"; }; + + elm: elm@48080000 { + compatible = "ti,am3352-elm"; + reg = <0x48080000 0x2000>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "elm"; + clocks = <&l4ls_gclk>; + clock-names = "fck"; + status = "disabled"; + }; + + gpmc: gpmc@50000000 { + compatible = "ti,am3352-gpmc"; + ti,hwmods = "gpmc"; + clocks = <&l3s_gclk>; + clock-names = "fck"; + reg = <0x50000000 0x2000>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + gpmc,num-cs = <7>; + gpmc,num-waitpins = <2>; + #address-cells = <2>; + #size-cells = <1>; + status = "disabled"; + }; }; }; diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts index a7d0db10a4f4..a3a53ce84f16 100644 --- a/arch/arm/boot/dts/am43x-epos-evm.dts +++ b/arch/arm/boot/dts/am43x-epos-evm.dts @@ -81,6 +81,27 @@ >; }; + nand_flash_x8: nand_flash_x8 { + pinctrl-single,pins = < + 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a0.SELQSPIorNAND/GPIO */ + 0x0 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x4 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0xc (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpmc_wpn */ + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + >; + }; + ecap0_pins: backlight_pins { pinctrl-single,pins = < 0x164 MUX_MODE0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ @@ -230,6 +251,92 @@ status = "okay"; }; +&elm { + status = "okay"; +}; + +&gpmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nand_flash_x8>; + ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ + nand@0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + ti,nand-ecc-opt = "bch8"; + ti,elm-id = <&elm>; + nand-bus-width = <8>; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <40>; /* tCEA + tCHZ + 1 */ + gpmc,cs-wr-off-ns = <40>; + gpmc,adv-on-ns = <0>; /* cs-on-ns */ + gpmc,adv-rd-off-ns = <25>; /* min( tALH + tALS + 1) */ + gpmc,adv-wr-off-ns = <25>; /* min( tALH + tALS + 1) */ + gpmc,we-on-ns = <0>; /* cs-on-ns */ + gpmc,we-off-ns = <20>; /* we-on-time + tWP + 2 */ + gpmc,oe-on-ns = <3>; /* cs-on-ns + tRR + 2 */ + gpmc,oe-off-ns = <30>; /* oe-on-ns + tRP + 2 */ + gpmc,access-ns = <30>; /* tCEA + 4*/ + gpmc,rd-cycle-ns = <40>; + gpmc,wr-cycle-ns = <40>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + /* MTD partition table */ + /* All SPL-* partitions are sized to minimal length + * which can be independently programmable. For + * NAND flash this is equal to size of erase-block */ + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "NAND.SPL"; + reg = <0x00000000 0x00040000>; + }; + partition@1 { + label = "NAND.SPL.backup1"; + reg = <0x00040000 0x00040000>; + }; + partition@2 { + label = "NAND.SPL.backup2"; + reg = <0x00080000 0x00040000>; + }; + partition@3 { + label = "NAND.SPL.backup3"; + reg = <0x000C0000 0x00040000>; + }; + partition@4 { + label = "NAND.u-boot-spl-os"; + reg = <0x00100000 0x00080000>; + }; + partition@5 { + label = "NAND.u-boot"; + reg = <0x00180000 0x00100000>; + }; + partition@6 { + label = "NAND.u-boot-env"; + reg = <0x00280000 0x00040000>; + }; + partition@7 { + label = "NAND.u-boot-env.backup1"; + reg = <0x002C0000 0x00040000>; + }; + partition@8 { + label = "NAND.kernel"; + reg = <0x00300000 0x00700000>; + }; + partition@9 { + label = "NAND.file-system"; + reg = <0x00800000 0x1F600000>; + }; + }; +}; + &epwmss0 { status = "okay"; }; diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index 6e89630f8022..499974a50e27 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -47,6 +47,11 @@ 1000000 1060000 1176000 1160000 >; + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ }; cpu@1 { device_type = "cpu"; @@ -464,6 +469,13 @@ ti,hwmods = "wd_timer2"; }; + hwspinlock: spinlock@4a0f6000 { + compatible = "ti,omap4-hwspinlock"; + reg = <0x4a0f6000 0x1000>; + ti,hwmods = "spinlock"; + #hwlock-cells = <1>; + }; + dmm@4e000000 { compatible = "ti,omap5-dmm"; reg = <0x4e000000 0x800>; diff --git a/arch/arm/boot/dts/omap2420.dtsi b/arch/arm/boot/dts/omap2420.dtsi index 60c605de22dd..85b1fb014c43 100644 --- a/arch/arm/boot/dts/omap2420.dtsi +++ b/arch/arm/boot/dts/omap2420.dtsi @@ -99,6 +99,7 @@ dmas = <&sdma 31>, <&sdma 32>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp2: mcbsp@48076000 { @@ -112,6 +113,7 @@ dmas = <&sdma 33>, <&sdma 34>; dma-names = "tx", "rx"; + status = "disabled"; }; msdi1: mmc@4809c000 { diff --git a/arch/arm/boot/dts/omap2430.dtsi b/arch/arm/boot/dts/omap2430.dtsi index d624345666f5..9d2f028fd687 100644 --- a/arch/arm/boot/dts/omap2430.dtsi +++ b/arch/arm/boot/dts/omap2430.dtsi @@ -113,6 +113,7 @@ dmas = <&sdma 31>, <&sdma 32>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp2: mcbsp@48076000 { @@ -128,6 +129,7 @@ dmas = <&sdma 33>, <&sdma 34>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp3: mcbsp@4808c000 { @@ -143,6 +145,7 @@ dmas = <&sdma 17>, <&sdma 18>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp4: mcbsp@4808e000 { @@ -158,6 +161,7 @@ dmas = <&sdma 19>, <&sdma 20>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp5: mcbsp@48096000 { @@ -173,6 +177,7 @@ dmas = <&sdma 21>, <&sdma 22>; dma-names = "tx", "rx"; + status = "disabled"; }; mmc1: mmc@4809c000 { diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index 447e714d435b..cba357023878 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -234,3 +234,7 @@ regulator-max-microvolt = <1800000>; regulator-always-on; }; + +&mcbsp2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index 5053766d369b..d01e9a76c5da 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -211,3 +211,7 @@ regulator-max-microvolt = <1800000>; regulator-always-on; }; + +&mcbsp2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/omap3-cm-t3517.dts b/arch/arm/boot/dts/omap3-cm-t3517.dts new file mode 100644 index 000000000000..d00502f4fd9b --- /dev/null +++ b/arch/arm/boot/dts/omap3-cm-t3517.dts @@ -0,0 +1,136 @@ +/* + * Support for CompuLab CM-T3517 + */ +/dts-v1/; + +#include "am3517.dtsi" +#include "omap3-cm-t3x.dtsi" + +/ { + model = "CompuLab CM-T3517"; + compatible = "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3"; + + vmmc: regulator-vmmc { + compatible = "regulator-fixed"; + regulator-name = "vmmc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + wl12xx_vmmc2: wl12xx_vmmc2 { + compatible = "regulator-fixed"; + regulator-name = "vw1271"; + pinctrl-names = "default"; + pinctrl-0 = < + &wl12xx_wkup_pins + &wl12xx_core_pins + >; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio1 6 GPIO_ACTIVE_HIGH >; /* gpio6 */ + startup-delay-us = <20000>; + enable-active-high; + }; + + wl12xx_vaux2: wl12xx_vaux2 { + compatible = "regulator-fixed"; + regulator-name = "vwl1271_vaux2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; +}; + +&omap3_pmx_wkup { + + wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */ + OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE4) /* sys_boot4.gpio_6 */ + >; + }; +}; + +&omap3_pmx_core { + + phy1_reset_pins: pinmux_hsusb1_phy_reset_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE4) /* uart2_tx.gpio_146 */ + >; + }; + + phy2_reset_pins: pinmux_hsusb2_phy_reset_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x217a, PIN_OUTPUT | MUX_MODE4) /* uart2_rx.gpio_147 */ + >; + }; + + otg_drv_vbus: pinmux_otg_drv_vbus { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50Mhz_clk.usb0_drvvbus */ + >; + }; + + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + >; + }; + + wl12xx_core_pins: pinmux_wl12xx_core_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs5.gpio_56 */ + OMAP3_CORE1_IOPAD(0x2176, PIN_INPUT_PULLUP | MUX_MODE4) /* uart2_rts.gpio_145 */ + >; + }; + + usb_hub_pins: pinmux_usb_hub_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2184, PIN_OUTPUT | MUX_MODE4) /* mcbsp4_clkx.gpio_152 - USB HUB RST */ + >; + }; +}; + +&hsusb1_phy { + pinctrl-names = "default"; + pinctrl-0 = <&phy1_reset_pins>; + reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>; +}; + +&hsusb2_phy { + pinctrl-names = "default"; + pinctrl-0 = <&phy2_reset_pins>; + reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; +}; + +&davinci_emac { + status = "okay"; +}; + +&davinci_mdio { + status = "okay"; +}; + +&am35x_otg_hs { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&otg_drv_vbus>; +}; + +&mmc1 { + vmmc-supply = <&vmmc>; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <&wl12xx_vmmc2>; + vmmc_aux-supply = <&wl12xx_vaux2>; + non-removable; + bus-width = <4>; + cap-power-off-card; +}; diff --git a/arch/arm/boot/dts/omap3-cm-t3530.dts b/arch/arm/boot/dts/omap3-cm-t3530.dts new file mode 100644 index 000000000000..9faf1cd1dcaa --- /dev/null +++ b/arch/arm/boot/dts/omap3-cm-t3530.dts @@ -0,0 +1,12 @@ +/* + * Support for CompuLab CM-T3530 + */ +/dts-v1/; + +#include "omap34xx.dtsi" +#include "omap3-cm-t3x30.dtsi" + +/ { + model = "CompuLab CM-T3530"; + compatible = "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3"; +}; diff --git a/arch/arm/boot/dts/omap3-cm-t3730.dts b/arch/arm/boot/dts/omap3-cm-t3730.dts index 486f4d6c4219..b3f9a50b3bc8 100644 --- a/arch/arm/boot/dts/omap3-cm-t3730.dts +++ b/arch/arm/boot/dts/omap3-cm-t3730.dts @@ -32,57 +32,26 @@ }; &omap3_pmx_core { - mmc1_pins: pinmux_mmc1_pins { - pinctrl-single,pins = < - 0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ - 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ - 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ - 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ - 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ - 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ - >; - }; mmc2_pins: pinmux_mmc2_pins { pinctrl-single,pins = < - 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ - 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ - 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ - 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ - 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ - 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ - >; - }; - - smsc1_pins: pinmux_smsc1_pins { - pinctrl-single,pins = < - 0x88 (PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs5.gpmc_ncs5 */ - 0x16a (PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 */ - >; - }; - - uart3_pins: pinmux_uart3_pins { - pinctrl-single,pins = < - 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ - 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ >; }; wl12xx_gpio: pinmux_wl12xx_gpio { pinctrl-single,pins = < - 0xb2 (PIN_OUTPUT | MUX_MODE4) /* dss_data3.gpio_73 */ - 0x134 (PIN_INPUT | MUX_MODE4) /* sdmmc2_dat4.gpio_136 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4) /* dss_data3.gpio_73 */ + OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT | MUX_MODE4) /* sdmmc2_dat4.gpio_136 */ >; }; }; -&mmc1 { - vmmc-supply = <&vmmc1>; - bus-width = <4>; - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins>; -}; - &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_pins>; @@ -92,13 +61,3 @@ bus-width = <4>; cap-power-off-card; }; - -&smsc1 { - pinctrl-names = "default"; - pinctrl-0 = <&smsc1_pins>; -}; - -&uart3 { - pinctrl-names = "default"; - pinctrl-0 = <&uart3_pins>; -}; diff --git a/arch/arm/boot/dts/omap3-cm-t3x.dtsi b/arch/arm/boot/dts/omap3-cm-t3x.dtsi new file mode 100644 index 000000000000..c671a2299ea8 --- /dev/null +++ b/arch/arm/boot/dts/omap3-cm-t3x.dtsi @@ -0,0 +1,110 @@ +/* + * Common support for CompuLab CM-T3x CoMs + */ + +/ { + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&green_led_pins>; + ledb { + label = "cm-t3x:green"; + gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>; /* gpio186 */ + linux,default-trigger = "heartbeat"; + }; + }; + + /* HS USB Port 1 Power */ + hsusb1_power: hsusb1_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb1_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <70000>; + }; + + /* HS USB Port 2 Power */ + hsusb2_power: hsusb2_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb2_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <70000>; + }; + + /* HS USB Host PHY on PORT 1 */ + hsusb1_phy: hsusb1_phy { + compatible = "usb-nop-xceiv"; + vcc-supply = <&hsusb1_power>; + }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + vcc-supply = <&hsusb2_power>; + }; +}; + +&omap3_pmx_core { + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + >; + }; + + green_led_pins: pinmux_green_led_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21e2, PIN_OUTPUT | MUX_MODE4) /* sys_clkout2.gpio_186 */ + >; + }; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + bus-width = <4>; +}; + +&mmc3 { + status = "disabled"; +}; + +&i2c1 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <400000>; +}; +&usbhshost { + port1-mode = "ehci-phy"; + port2-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <&hsusb1_phy &hsusb2_phy>; +}; diff --git a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi index 3a9f004d8924..d00055809e31 100644 --- a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi +++ b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi @@ -1,28 +1,16 @@ /* - * Common support for CompuLab CM-T3530 and CM-T3730 + * Common support for CompuLab CM-T3x30 CoMs */ -/ { - memory { - device_type = "memory"; - reg = <0x80000000 0x10000000>; /* 256 MB */ - }; +#include "omap3-cm-t3x.dtsi" +/ { cpus { cpu@0 { cpu0-supply = <&vcc>; }; }; - leds { - compatible = "gpio-leds"; - ledb { - label = "cm-t35:green"; - gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>; /* gpio186 */ - linux,default-trigger = "heartbeat"; - }; - }; - vddvario: regulator-vddvario { compatible = "regulator-fixed"; regulator-name = "vddvario"; @@ -36,11 +24,40 @@ }; }; +&omap3_pmx_core { + + smsc1_pins: pinmux_smsc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs5.gpmc_ncs5 */ + OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 */ + >; + }; + + hsusb0_pins: pinmux_hsusb0_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */ + OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */ + OMAP3_CORE1_IOPAD(0x21a4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */ + OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */ + OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data0.hsusb2_data0 */ + OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */ + OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */ + OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data3 */ + OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data4 */ + OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data5 */ + OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data6 */ + OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */ + >; + }; +}; + &gpmc { ranges = <5 0 0x2c000000 0x01000000>; smsc1: ethernet@5,0 { compatible = "smsc,lan9221", "smsc,lan9115"; + pinctrl-names = "default"; + pinctrl-0 = <&smsc1_pins>; interrupt-parent = <&gpio6>; interrupts = <3 IRQ_TYPE_LEVEL_LOW>; reg = <5 0 0xff>; @@ -74,8 +91,6 @@ }; &i2c1 { - clock-frequency = <400000>; - twl: twl@48 { reg = <0x48>; interrupts = <7>; /* SYS_NIRQ cascaded to intc */ @@ -86,10 +101,31 @@ #include "twl4030.dtsi" #include "twl4030_omap3.dtsi" -&i2c3 { - clock-frequency = <400000>; +&mmc1 { + vmmc-supply = <&vmmc1>; }; &twl_gpio { ti,use-leds; + /* pullups: BIT(0) */ + ti,pullups = <0x000001>; +}; + +&hsusb1_phy { + reset-gpios = <&twl_gpio 6 GPIO_ACTIVE_LOW>; +}; + +&hsusb2_phy { + reset-gpios = <&twl_gpio 7 GPIO_ACTIVE_LOW>; +}; + +&usb_otg_hs { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb0_pins>; + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; }; diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts b/arch/arm/boot/dts/omap3-devkit8000.dts index 4665421bb7bc..bf5a515a3247 100644 --- a/arch/arm/boot/dts/omap3-devkit8000.dts +++ b/arch/arm/boot/dts/omap3-devkit8000.dts @@ -101,20 +101,8 @@ status = "disabled"; }; -&mcbsp1 { - status = "disabled"; -}; - -&mcbsp3 { - status = "disabled"; -}; - -&mcbsp4 { - status = "disabled"; -}; - -&mcbsp5 { - status = "disabled"; +&mcbsp2 { + status = "okay"; }; &gpmc { diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts index b9b55c95a566..3ad9fddf2eb6 100644 --- a/arch/arm/boot/dts/omap3-gta04.dts +++ b/arch/arm/boot/dts/omap3-gta04.dts @@ -36,6 +36,14 @@ gpio-key,wakeup; }; }; + + sound { + compatible = "ti,omap-twl4030"; + ti,model = "gta04"; + + ti,mcbsp = <&mcbsp2>; + ti,codec = <&twl_audio>; + }; }; &omap3_pmx_core { @@ -80,6 +88,12 @@ interrupts = <7>; /* SYS_NIRQ cascaded to intc */ interrupt-parent = <&intc>; }; + + twl_audio: audio { + compatible = "ti,twl4030-audio"; + codec { + }; + }; }; #include "twl4030.dtsi" @@ -94,6 +108,14 @@ reg = <0x77>; }; + /* accelerometer */ + bma180@41 { + compatible = "bosch,bma180"; + reg = <0x41>; + interrupt-parent = <&gpio3>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + }; + /* leds */ tca6507@45 { compatible = "ti,tca6507"; @@ -122,6 +144,22 @@ reg = <0x4>; }; }; + + /* compass aka magnetometer */ + hmc5843@1e { + compatible = "honeywell,hmc5843"; + reg = <0x1e>; + }; + + /* touchscreen */ + tsc2007@48 { + compatible = "ti,tsc2007"; + reg = <0x48>; + interrupt-parent = <&gpio6>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + gpios = <&gpio6 0 GPIO_ACTIVE_LOW>; + ti,x-plate-ohms = <600>; + }; }; &i2c3 { @@ -146,7 +184,9 @@ }; &mmc2 { - status = "disabled"; + vmmc-supply = <&vaux4>; + bus-width = <4>; + ti,non-removable; }; &mmc3 { @@ -168,3 +208,12 @@ pinctrl-0 = <&uart3_pins>; }; +&charger { + bb_uvolt = <3200000>; + bb_uamp = <150>; +}; + +&vaux4 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3150000>; +}; diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index c17009323520..b97736d98a64 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -170,6 +170,7 @@ &mcbsp2 { pinctrl-names = "default"; pinctrl-0 = <&mcbsp2_pins>; + status = "okay"; }; &mmc1 { diff --git a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi new file mode 100644 index 000000000000..6369d9f43ca2 --- /dev/null +++ b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi @@ -0,0 +1,459 @@ +/* + * Copyright (C) 2014 Christoph Fritz <chf.fritzc@googlemail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include "omap36xx.dtsi" + +/ { + model = "INCOstartec LILLY-A83X module (DM3730)"; + compatible = "incostartec,omap3-lilly-a83x", "ti,omap36xx", "ti,omap3"; + + chosen { + bootargs = "console=ttyO0,115200n8 vt.global_cursor_default=0 consoleblank=0"; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x8000000>; /* 128 MB */ + }; + + leds { + compatible = "gpio-leds"; + + led1 { + label = "lilly-a83x::led1"; + gpios = <&gpio1 29 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-on"; + }; + + }; + + sound { + compatible = "ti,omap-twl4030"; + ti,model = "lilly-a83x"; + + ti,mcbsp = <&mcbsp2>; + ti,codec = <&twl_audio>; + }; + + reg_vcc3: vcc3 { + compatible = "regulator-fixed"; + regulator-name = "VCC3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + hsusb1_phy: hsusb1_phy { + compatible = "usb-nop-xceiv"; + vcc-supply = <®_vcc3>; + }; +}; + +&omap3_pmx_wkup { + pinctrl-names = "default"; + + lan9221_pins: pinmux_lan9221_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a5a, PIN_INPUT | MUX_MODE4) /* reserved.gpio_129 */ + >; + }; + + tsc2048_pins: pinmux_tsc2048_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a16, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot6.gpio_8 */ + >; + }; + + mmc1cd_pins: pinmux_mmc1cd_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a56, PIN_INPUT | MUX_MODE4) /* reserved.gpio_126 */ + >; + }; +}; + +&omap3_pmx_core { + pinctrl-names = "default"; + + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_tx */ + OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE0) /* uart1_rts.uart1_rts */ + OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT | MUX_MODE0) /* uart1_cts.uart1_cts */ + OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */ + >; + }; + + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2170, PIN_OUTPUT | MUX_MODE1) /* mcbsp3_clkx.uart2_tx */ + OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE1) /* mcbsp3_fsx.uart2_rx */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21ba ,PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl.i2c1_scl */ + OMAP3_CORE1_IOPAD(0x21bc ,PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda.i2c1_sda */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl.i2c2_scl */ + OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda.i2c2_sda */ + >; + }; + + i2c3_pins: pinmux_i2c3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl.i2c3_scl */ + OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda.i2c3_sda */ + >; + }; + + hsusb1_pins: pinmux_hsusb1_pins { + pinctrl-single,pins = < + + /* GPIO 182 controls USB-Hub reset. But USB-Phy its + * reset can't be controlled. So we clamp this GPIO to + * high (PIN_OFF_OUTPUT_HIGH) to always enable USB-Hub. + */ + + OMAP3_CORE1_IOPAD(0x21de, PIN_OUTPUT_PULLUP | PIN_OFF_OUTPUT_HIGH | MUX_MODE4) /* mcspi2_cs1.gpio_182 */ + >; + }; + + hsusb_otg_pins: pinmux_hsusb_otg_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */ + OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */ + OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */ + OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */ + OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */ + OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */ + OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */ + OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */ + OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */ + OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */ + OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */ + OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + >; + }; + + spi2_pins: pinmux_spi2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcspi2_clk.mcspi2_clk */ + OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcspi2_simo.mcspi2_simo */ + OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcspi2_somi.mcspi2_somi */ + OMAP3_CORE1_IOPAD(0x21dc, PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0.mcspi2_cs0 */ + >; + }; +}; + +&omap3_pmx_core2 { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusb1_2_pins + >; + + hsusb1_2_pins: pinmux_hsusb1_2_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE3) /* etk_clk.hsusb1_stp */ + OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT | MUX_MODE3) /* etk_ctl.hsusb1_clk */ + OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE3) /* etk_d0.hsusb1_data0 */ + OMAP3630_CORE2_IOPAD(0x25de, PIN_INPUT | MUX_MODE3) /* etk_d1.hsusb1_data1 */ + OMAP3630_CORE2_IOPAD(0x25e0, PIN_INPUT | MUX_MODE3) /* etk_d2.hsusb1_data2 */ + OMAP3630_CORE2_IOPAD(0x25e2, PIN_INPUT | MUX_MODE3) /* etk_d3.hsusb1_data7 */ + OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT | MUX_MODE3) /* etk_d4.hsusb1_data4 */ + OMAP3630_CORE2_IOPAD(0x25e6, PIN_INPUT | MUX_MODE3) /* etk_d5.hsusb1_data5 */ + OMAP3630_CORE2_IOPAD(0x25e8, PIN_INPUT | MUX_MODE3) /* etk_d6.hsusb1_data6 */ + OMAP3630_CORE2_IOPAD(0x25ea, PIN_INPUT | MUX_MODE3) /* etk_d7.hsusb1_data3 */ + OMAP3630_CORE2_IOPAD(0x25ec, PIN_INPUT | MUX_MODE3) /* etk_d8.hsusb1_dir */ + OMAP3630_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE3) /* etk_d9.hsusb1_nxt */ + >; + }; + + gpio1_pins: pinmux_gpio1_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25fa, PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* etk_d15.gpio_29 */ + >; + }; + +}; + +&gpio1 { + pinctrl-names = "default"; + pinctrl-0 = <&gpio1_pins>; +}; + +&gpio6 { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb1_pins>; +}; + +&i2c1 { + clock-frequency = <2600000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + twl_audio: audio { + compatible = "ti,twl4030-audio"; + codec { + }; + }; + }; +}; + +#include "twl4030.dtsi" +#include "twl4030_omap3.dtsi" + +&twl { + vmmc1: regulator-vmmc1 { + regulator-always-on; + }; + + vdd1: regulator-vdd1 { + regulator-always-on; + }; + + vdd2: regulator-vdd2 { + regulator-always-on; + }; +}; + +&i2c2 { + clock-frequency = <2600000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; +}; + +&i2c3 { + clock-frequency = <2600000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; + gpiom1: gpio@20 { + compatible = "mcp,mcp23017"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; +}; + +&uart4 { + status = "disabled"; +}; + +&mmc1 { + cd-gpios = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>; + cd-inverted; + vmmc-supply = <&vmmc1>; + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins &mmc1cd_pins>; + cap-sdio-irq; + cap-sd-highspeed; + cap-mmc-highspeed; +}; + +&mmc2 { + status = "disabled"; +}; + +&mmc3 { + status = "disabled"; +}; + +&mcspi2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins>; + + tsc2046@0 { + reg = <0>; /* CS0 */ + compatible = "ti,tsc2046"; + interrupt-parent = <&gpio1>; + interrupts = <8 0>; /* boot6 / gpio_8 */ + spi-max-frequency = <1000000>; + pendown-gpio = <&gpio1 8 0>; + vcc-supply = <®_vcc3>; + pinctrl-names = "default"; + pinctrl-0 = <&tsc2048_pins>; + + ti,x-min = <300>; + ti,x-max = <3000>; + ti,y-min = <600>; + ti,y-max = <3600>; + ti,x-plate-ohms = <80>; + ti,pressure-max = <255>; + ti,swap-xy; + + linux,wakeup; + }; +}; + +&usbhsehci { + phys = <&hsusb1_phy>; +}; + +&usbhshost { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb1_2_pins>; + num-ports = <2>; + port1-mode = "ehci-phy"; +}; + +&usb_otg_hs { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb_otg_pins>; + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x1000000>, + <7 0 0x15000000 0x01000000>; + + nand@0,0 { + reg = <0 0 0x1000000>; + nand-bus-width = <16>; + ti,nand-ecc-opt = "bch8"; + /* no elm on omap3 */ + + gpmc,mux-add-data = <0>; + gpmc,device-nand; + gpmc,device-width = <2>; + gpmc,wait-pin = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,burst-length= <4>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <100>; + gpmc,cs-wr-off-ns = <100>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <100>; + gpmc,adv-wr-off-ns = <100>; + gpmc,oe-on-ns = <5>; + gpmc,oe-off-ns = <75>; + gpmc,we-on-ns = <5>; + gpmc,we-off-ns = <75>; + gpmc,rd-cycle-ns = <100>; + gpmc,wr-cycle-ns = <100>; + gpmc,access-ns = <60>; + gpmc,page-burst-access-ns = <5>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-delay-ns = <50>; + gpmc,wr-data-mux-bus-ns = <75>; + gpmc,wr-access-ns = <155>; + + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "MLO"; + reg = <0 0x80000>; + }; + + partition@0x80000 { + label = "u-boot"; + reg = <0x80000 0x1e0000>; + }; + + partition@0x260000 { + label = "u-boot-environment"; + reg = <0x260000 0x20000>; + }; + + partition@0x280000 { + label = "kernel"; + reg = <0x280000 0x500000>; + }; + + partition@0x780000 { + label = "filesystem"; + reg = <0x780000 0xf880000>; + }; + }; + + ethernet@7,0 { + compatible = "smsc,lan9221", "smsc,lan9115"; + bank-width = <2>; + gpmc,mux-add-data = <2>; + gpmc,cs-on-ns = <10>; + gpmc,cs-rd-off-ns = <60>; + gpmc,cs-wr-off-ns = <60>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <10>; + gpmc,adv-wr-off-ns = <10>; + gpmc,oe-on-ns = <10>; + gpmc,oe-off-ns = <60>; + gpmc,we-on-ns = <10>; + gpmc,we-off-ns = <60>; + gpmc,rd-cycle-ns = <100>; + gpmc,wr-cycle-ns = <100>; + gpmc,access-ns = <50>; + gpmc,page-burst-access-ns = <5>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <75>; + gpmc,wr-data-mux-bus-ns = <15>; + gpmc,wr-access-ns = <75>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-diffcsen; + vddvario-supply = <®_vcc3>; + vdd33a-supply = <®_vcc3>; + reg-io-width = <4>; + interrupt-parent = <&gpio5>; + interrupts = <1 0x2>; + reg = <7 0 0xff>; + pinctrl-names = "default"; + pinctrl-0 = <&lan9221_pins>; + phy-mode = "mii"; + }; +}; diff --git a/arch/arm/boot/dts/omap3-lilly-dbb056.dts b/arch/arm/boot/dts/omap3-lilly-dbb056.dts new file mode 100644 index 000000000000..834f7c65f62d --- /dev/null +++ b/arch/arm/boot/dts/omap3-lilly-dbb056.dts @@ -0,0 +1,170 @@ +/* + * Copyright (C) 2014 Christoph Fritz <chf.fritzc@googlemail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ +/dts-v1/; + +#include "omap3-lilly-a83x.dtsi" + +/ { + model = "INCOstartec LILLY-DBB056 (DM3730)"; + compatible = "incostartec,omap3-lilly-dbb056", "incostartec,omap3-lilly-a83x", "ti,omap36xx", "ti,omap3"; +}; + +&twl { + vaux2: regulator-vaux2 { + compatible = "ti,twl4030-vaux2"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; +}; + +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pins>; + + lan9117_pins: pinmux_lan9117_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT | MUX_MODE4) /* cam_fld.gpio_98 */ + >; + }; + + gpio4_pins: pinmux_gpio4_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT | MUX_MODE4) /* cam_xclkb.gpio_111 -> sja1000 IRQ */ + >; + }; + + gpio5_pins: pinmux_gpio5_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x218c, PIN_OUTPUT | PIN_OFF_OUTPUT_HIGH | MUX_MODE4) /* mcbsp1_clk.gpio_156 -> enable DSS */ + >; + }; + + lcd_pins: pinmux_lcd_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ + OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ + >; + }; + + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dir_dat0 */ + OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dir_dat1 */ + OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dir_cmd */ + OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */ + OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 -> wp */ + OMAP3_CORE1_IOPAD(0x219c, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_rts_sd.gpio_164 -> cd */ + >; + }; + + spi1_pins: pinmux_spi1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ + OMAP3_CORE1_IOPAD(0x21ca, PIN_INPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ + OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ + OMAP3_CORE1_IOPAD(0x21ce, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ + >; + }; +}; + +&gpio4 { + pinctrl-names = "default"; + pinctrl-0 = <&gpio4_pins>; +}; + +&gpio5 { + pinctrl-names = "default"; + pinctrl-0 = <&gpio5_pins>; +}; + +&mmc2 { + status = "okay"; + bus-width = <4>; + vmmc-supply = <&vmmc1>; + cd-gpios = <&gpio6 4 0>; /* gpio_164 */ + wp-gpios = <&gpio6 3 0>; /* gpio_163 */ + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + ti,dual-volt; +}; + +&mcspi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins>; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x1000000>, /* nand assigned by COM a83x */ + <4 0 0x20000000 0x01000000>, + <7 0 0x15000000 0x01000000>; /* eth assigend by COM a83x */ + + ethernet@4,0 { + compatible = "smsc,lan9117", "smsc,lan9115"; + bank-width = <2>; + gpmc,mux-add-data = <2>; + gpmc,cs-on-ns = <10>; + gpmc,cs-rd-off-ns = <65>; + gpmc,cs-wr-off-ns = <65>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <10>; + gpmc,adv-wr-off-ns = <10>; + gpmc,oe-on-ns = <10>; + gpmc,oe-off-ns = <65>; + gpmc,we-on-ns = <10>; + gpmc,we-off-ns = <65>; + gpmc,rd-cycle-ns = <100>; + gpmc,wr-cycle-ns = <100>; + gpmc,access-ns = <60>; + gpmc,page-burst-access-ns = <5>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <75>; + gpmc,wr-data-mux-bus-ns = <15>; + gpmc,wr-access-ns = <75>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-diffcsen; + vddvario-supply = <®_vcc3>; + vdd33a-supply = <®_vcc3>; + reg-io-width = <4>; + interrupt-parent = <&gpio4>; + interrupts = <2 0x2>; + reg = <4 0 0xff>; + pinctrl-names = "default"; + pinctrl-0 = <&lan9117_pins>; + phy-mode = "mii"; + smsc,force-internal-phy; + }; +}; diff --git a/arch/arm/boot/dts/omap3-overo.dtsi b/arch/arm/boot/dts/omap3-overo.dtsi index a461d2fd1fb0..b08142f755fd 100644 --- a/arch/arm/boot/dts/omap3-overo.dtsi +++ b/arch/arm/boot/dts/omap3-overo.dtsi @@ -95,3 +95,7 @@ pinctrl-names = "default"; pinctrl-0 = <&uart3_pins>; }; + +&mcbsp2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/omap3-sb-t35.dtsi b/arch/arm/boot/dts/omap3-sb-t35.dtsi index b9a2fedce7ee..7909c51b05a5 100644 --- a/arch/arm/boot/dts/omap3-sb-t35.dtsi +++ b/arch/arm/boot/dts/omap3-sb-t35.dtsi @@ -2,11 +2,36 @@ * Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730 */ +/ { + vddvario_sb_t35: regulator-vddvario-sb-t35 { + compatible = "regulator-fixed"; + regulator-name = "vddvario"; + regulator-always-on; + }; + + vdd33a_sb_t35: regulator-vdd33a-sb-t35 { + compatible = "regulator-fixed"; + regulator-name = "vdd33a"; + regulator-always-on; + }; +}; + +&omap3_pmx_core { + smsc2_pins: pinmux_smsc2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20b6, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs4.gpmc_ncs4 */ + OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_wait3.gpio_65 */ + >; + }; +}; + &gpmc { ranges = <4 0 0x2d000000 0x01000000>; smsc2: ethernet@4,0 { compatible = "smsc,lan9221", "smsc,lan9115"; + pinctrl-names = "default"; + pinctrl-0 = <&smsc2_pins>; interrupt-parent = <&gpio3>; interrupts = <1 IRQ_TYPE_LEVEL_LOW>; reg = <4 0 0xff>; @@ -32,8 +57,8 @@ gpmc,wr-access-ns = <186>; gpmc,cycle2cycle-samecsen; gpmc,cycle2cycle-diffcsen; - vddvario-supply = <&vddvario>; - vdd33a-supply = <&vdd33a>; + vddvario-supply = <&vddvario_sb_t35>; + vdd33a-supply = <&vdd33a_sb_t35>; reg-io-width = <4>; smsc,save-mac-address; }; diff --git a/arch/arm/boot/dts/omap3-sbc-t3517.dts b/arch/arm/boot/dts/omap3-sbc-t3517.dts new file mode 100644 index 000000000000..024c9c6c682d --- /dev/null +++ b/arch/arm/boot/dts/omap3-sbc-t3517.dts @@ -0,0 +1,43 @@ +/* + * Suppport for CompuLab SBC-T3517 with CM-T3517 + */ + +#include "omap3-cm-t3517.dts" +#include "omap3-sb-t35.dtsi" + +/ { + model = "CompuLab SBC-T3517 with CM-T3517"; + compatible = "compulab,omap3-sbc-t3517", "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3"; +}; + +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &sb_t35_usb_hub_pins + &usb_hub_pins + >; + + mmc1_aux_pins: pinmux_mmc1_aux_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20c0, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_clk.gpio_59 */ + OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE4) /* uart2_cts.gpio_144 */ + >; + }; + + sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21ec, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_98 - SB-T35 USB HUB RST */ + >; + }; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = < + &mmc1_pins + &mmc1_aux_pins + >; + + wp-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>; /* gpio_59 */ + cd-gpios = <&gpio5 16 GPIO_ACTIVE_HIGH>; /* gpio_144 */ +}; diff --git a/arch/arm/boot/dts/omap3-sbc-t3530.dts b/arch/arm/boot/dts/omap3-sbc-t3530.dts new file mode 100644 index 000000000000..bbbeea6b1988 --- /dev/null +++ b/arch/arm/boot/dts/omap3-sbc-t3530.dts @@ -0,0 +1,36 @@ +/* + * Suppport for CompuLab SBC-T3530 with CM-T3530 + */ + +#include "omap3-cm-t3530.dts" +#include "omap3-sb-t35.dtsi" + +/ { + model = "CompuLab SBC-T3530 with CM-T3530"; + compatible = "compulab,omap3-sbc-t3530", "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3"; +}; + +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = <&sb_t35_usb_hub_pins>; + + sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35 USB HUB RST */ + >; + }; +}; + +/* + * The following ranges correspond to SMSC9x eth chips on CM-T3530 CoM and + * SB-T35 baseboard respectively. + * This setting includes both chips in SBC-T3530 board device tree. + */ +&gpmc { + ranges = <5 0 0x2c000000 0x01000000>, + <4 0 0x2d000000 0x01000000>; +}; + +&mmc1 { + cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_HIGH>; +}; diff --git a/arch/arm/boot/dts/omap3-sbc-t3730.dts b/arch/arm/boot/dts/omap3-sbc-t3730.dts index c119bd545053..08e4a7086f22 100644 --- a/arch/arm/boot/dts/omap3-sbc-t3730.dts +++ b/arch/arm/boot/dts/omap3-sbc-t3730.dts @@ -10,21 +10,18 @@ compatible = "compulab,omap3-sbc-t3730", "compulab,omap3-cm-t3730", "ti,omap36xx", "ti,omap3"; }; -&gpmc { - ranges = <5 0 0x2c000000 0x01000000>, - <4 0 0x2d000000 0x01000000>; -}; - -&smsc2 { +&omap3_pmx_core { pinctrl-names = "default"; - pinctrl-0 = <&smsc2_pins>; -}; + pinctrl-0 = <&sb_t35_usb_hub_pins>; -&omap3_pmx_core { - smsc2_pins: pinmux_smsc2_pins { + sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins { pinctrl-single,pins = < - 0x86 (PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs4.gpmc_ncs4 */ - 0xa2 (PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_wait3.gpio_65 */ + OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35 USB HUB RST */ >; }; -};
\ No newline at end of file +}; + +&gpmc { + ranges = <5 0 0x2c000000 0x01000000>, + <4 0 0x2d000000 0x01000000>; +}; diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index a5fc83b9c835..d3924198e5fd 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -35,6 +35,11 @@ compatible = "arm,cortex-a8"; device_type = "cpu"; reg = <0x0>; + + clocks = <&dpll1_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ }; }; @@ -436,6 +441,7 @@ dmas = <&sdma 31>, <&sdma 32>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp2: mcbsp@49022000 { @@ -453,6 +459,7 @@ dmas = <&sdma 33>, <&sdma 34>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp3: mcbsp@49024000 { @@ -470,6 +477,7 @@ dmas = <&sdma 17>, <&sdma 18>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp4: mcbsp@49026000 { @@ -485,6 +493,7 @@ dmas = <&sdma 19>, <&sdma 20>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp5: mcbsp@48096000 { @@ -500,6 +509,7 @@ dmas = <&sdma 21>, <&sdma 22>; dma-names = "tx", "rx"; + status = "disabled"; }; sham: sham@480c3000 { diff --git a/arch/arm/boot/dts/omap3430-sdp.dts b/arch/arm/boot/dts/omap3430-sdp.dts index cd3d0474acc9..02f69f4a8fd3 100644 --- a/arch/arm/boot/dts/omap3430-sdp.dts +++ b/arch/arm/boot/dts/omap3430-sdp.dts @@ -107,9 +107,8 @@ #address-cells = <1>; #size-cells = <1>; reg = <1 0 0x08000000>; + ti,nand-ecc-opt = "ham1"; nand-bus-width = <8>; - - ti,nand-ecc-opt = "sw"; gpmc,cs-on-ns = <0>; gpmc,cs-rd-off-ns = <36>; gpmc,cs-wr-off-ns = <36>; diff --git a/arch/arm/boot/dts/omap3430es1-clocks.dtsi b/arch/arm/boot/dts/omap3430es1-clocks.dtsi index 02f6c7fabbec..6f31954636a1 100644 --- a/arch/arm/boot/dts/omap3430es1-clocks.dtsi +++ b/arch/arm/boot/dts/omap3430es1-clocks.dtsi @@ -82,16 +82,16 @@ ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>; }; - ssi_ssr_fck_3430es1: ssi_ssr_fck_3430es1 { + ssi_ssr_fck: ssi_ssr_fck_3430es1 { #clock-cells = <0>; compatible = "ti,composite-clock"; clocks = <&ssi_ssr_gate_fck_3430es1>, <&ssi_ssr_div_fck_3430es1>; }; - ssi_sst_fck_3430es1: ssi_sst_fck_3430es1 { + ssi_sst_fck: ssi_sst_fck_3430es1 { #clock-cells = <0>; compatible = "fixed-factor-clock"; - clocks = <&ssi_ssr_fck_3430es1>; + clocks = <&ssi_ssr_fck>; clock-mult = <1>; clock-div = <2>; }; @@ -120,7 +120,7 @@ clock-div = <1>; }; - ssi_ick_3430es1: ssi_ick_3430es1 { + ssi_ick: ssi_ick_3430es1 { #clock-cells = <0>; compatible = "ti,omap3-no-wait-interface-clock"; clocks = <&ssi_l4_ick>; @@ -203,6 +203,6 @@ <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>, <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>, <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>, - <&fshostusb_fck>, <&fac_ick>, <&ssi_ick_3430es1>; + <&fshostusb_fck>, <&fac_ick>, <&ssi_ick>; }; }; diff --git a/arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi b/arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi index 8ed475dd63c9..877318c28364 100644 --- a/arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi +++ b/arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi @@ -25,16 +25,16 @@ ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>; }; - ssi_ssr_fck_3430es2: ssi_ssr_fck_3430es2 { + ssi_ssr_fck: ssi_ssr_fck_3430es2 { #clock-cells = <0>; compatible = "ti,composite-clock"; clocks = <&ssi_ssr_gate_fck_3430es2>, <&ssi_ssr_div_fck_3430es2>; }; - ssi_sst_fck_3430es2: ssi_sst_fck_3430es2 { + ssi_sst_fck: ssi_sst_fck_3430es2 { #clock-cells = <0>; compatible = "fixed-factor-clock"; - clocks = <&ssi_ssr_fck_3430es2>; + clocks = <&ssi_ssr_fck>; clock-mult = <1>; clock-div = <2>; }; @@ -55,7 +55,7 @@ clock-div = <1>; }; - ssi_ick_3430es2: ssi_ick_3430es2 { + ssi_ick: ssi_ick_3430es2 { #clock-cells = <0>; compatible = "ti,omap3-ssi-interface-clock"; clocks = <&ssi_l4_ick>; @@ -193,6 +193,6 @@ <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>, <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>, <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>, - <&ssi_ick_3430es2>; + <&ssi_ick>; }; }; diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 88c6a05cab41..f83dd4c365c7 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -109,9 +109,6 @@ &omap4_pmx_core { pinctrl-names = "default"; pinctrl-0 = < - &twl6040_pins - &mcpdm_pins - &mcbsp1_pins &dss_dpi_pins &tfp410_pins &dss_hdmi_pins @@ -300,6 +297,10 @@ twl6040: twl@4b { compatible = "ti,twl6040"; reg = <0x4b>; + + pinctrl-names = "default"; + pinctrl-0 = <&twl6040_pins>; + /* IRQ# = 119 */ interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */ interrupt-parent = <&gic>; @@ -380,16 +381,16 @@ device-handle = <&elpida_ECB240ABACN>; }; -&mcbsp2 { - status = "disabled"; -}; - -&mcbsp3 { - status = "disabled"; +&mcbsp1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp1_pins>; + status = "okay"; }; -&dmic { - status = "disabled"; +&mcpdm { + pinctrl-names = "default"; + pinctrl-0 = <&mcpdm_pins>; + status = "okay"; }; &twl_usb_comparator { diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index dbc81fb6ef03..9bbbbec1d63d 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -158,11 +158,6 @@ &omap4_pmx_core { pinctrl-names = "default"; pinctrl-0 = < - &twl6040_pins - &mcpdm_pins - &dmic_pins - &mcbsp1_pins - &mcbsp2_pins &dss_hdmi_pins &tpd12s015_pins >; @@ -326,6 +321,10 @@ twl6040: twl@4b { compatible = "ti,twl6040"; reg = <0x4b>; + + pinctrl-names = "default"; + pinctrl-0 = <&twl6040_pins>; + /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */ interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */ interrupt-parent = <&gic>; @@ -537,8 +536,28 @@ pinctrl-0 = <&uart4_pins>; }; -&mcbsp3 { - status = "disabled"; +&mcbsp1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp1_pins>; + status = "okay"; +}; + +&mcbsp2 { + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp2_pins>; + status = "okay"; +}; + +&dmic { + pinctrl-names = "default"; + pinctrl-0 = <&dmic_pins>; + status = "okay"; +}; + +&mcpdm { + pinctrl-names = "default"; + pinctrl-0 = <&mcpdm_pins>; + status = "okay"; }; &twl_usb_comparator { diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 1b4f59bed0f5..afa23bcf6f44 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -36,6 +36,11 @@ device_type = "cpu"; next-level-cache = <&L2>; reg = <0x0>; + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ }; cpu@1 { compatible = "arm,cortex-a9"; @@ -313,6 +318,7 @@ compatible = "ti,omap4-hwspinlock"; reg = <0x4a0f6000 0x1000>; ti,hwmods = "spinlock"; + #hwlock-cells = <1>; }; i2c1: i2c@48070000 { @@ -478,6 +484,7 @@ dmas = <&sdma 65>, <&sdma 66>; dma-names = "up_link", "dn_link"; + status = "disabled"; }; dmic: dmic@4012e000 { @@ -489,6 +496,7 @@ ti,hwmods = "dmic"; dmas = <&sdma 67>; dma-names = "up_link"; + status = "disabled"; }; mcbsp1: mcbsp@40122000 { @@ -503,6 +511,7 @@ dmas = <&sdma 33>, <&sdma 34>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp2: mcbsp@40124000 { @@ -517,6 +526,7 @@ dmas = <&sdma 17>, <&sdma 18>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp3: mcbsp@40126000 { @@ -531,6 +541,7 @@ dmas = <&sdma 19>, <&sdma 20>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp4: mcbsp@48096000 { @@ -544,6 +555,7 @@ dmas = <&sdma 31>, <&sdma 32>; dma-names = "tx", "rx"; + status = "disabled"; }; keypad: keypad@4a31c000 { diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index 4c3e9f125475..7fe682562dad 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -49,6 +49,12 @@ 1000000 1060000 1500000 1250000 >; + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ + /* cooling options */ cooling-min-level = <0>; cooling-max-level = <2>; @@ -353,6 +359,7 @@ compatible = "ti,omap4-hwspinlock"; reg = <0x4a0f6000 0x1000>; ti,hwmods = "spinlock"; + #hwlock-cells = <1>; }; mcspi1: spi@48098000 { @@ -529,6 +536,7 @@ dmas = <&sdma 65>, <&sdma 66>; dma-names = "up_link", "dn_link"; + status = "disabled"; }; dmic: dmic@4012e000 { @@ -540,6 +548,7 @@ ti,hwmods = "dmic"; dmas = <&sdma 67>; dma-names = "up_link"; + status = "disabled"; }; mcbsp1: mcbsp@40122000 { @@ -554,6 +563,7 @@ dmas = <&sdma 33>, <&sdma 34>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp2: mcbsp@40124000 { @@ -568,6 +578,7 @@ dmas = <&sdma 17>, <&sdma 18>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp3: mcbsp@40126000 { @@ -582,6 +593,7 @@ dmas = <&sdma 19>, <&sdma 20>; dma-names = "tx", "rx"; + status = "disabled"; }; timer1: timer@4ae18000 { diff --git a/arch/arm/boot/dts/tps65910.dtsi b/arch/arm/boot/dts/tps65910.dtsi index 92693a89160e..b0ac6657a170 100644 --- a/arch/arm/boot/dts/tps65910.dtsi +++ b/arch/arm/boot/dts/tps65910.dtsi @@ -82,5 +82,10 @@ reg = <12>; regulator-compatible = "vmmc"; }; + + vbb_reg: regulator@13 { + reg = <13>; + regulator-compatible = "vbb"; + }; }; }; |
