diff options
Diffstat (limited to 'arch/arm/boot/dts/omap5-uevm.dts')
| -rw-r--r-- | arch/arm/boot/dts/omap5-uevm.dts | 485 |
1 files changed, 485 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts new file mode 100644 index 000000000000..08b72678abff --- /dev/null +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -0,0 +1,485 @@ +/* + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "omap5.dtsi" +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> + +/ { + model = "TI OMAP5 uEVM board"; + compatible = "ti,omap5-uevm", "ti,omap5"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x7F000000>; /* 2032 MB */ + }; + + vmmcsd_fixed: fixedregulator-mmcsd { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + /* HS USB Port 2 RESET */ + hsusb2_reset: hsusb2_reset_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb2_reset"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 HUB_NRESET */ + startup-delay-us = <70000>; + enable-active-high; + }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-supply = <&hsusb2_reset>; + /** + * FIXME + * Put the right clock phandle here when available + * clocks = <&auxclk1>; + * clock-names = "main_clk"; + */ + clock-frequency = <19200000>; + }; + + /* HS USB Port 3 RESET */ + hsusb3_reset: hsusb3_reset_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb3_reset"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>; /* gpio3_79 ETH_NRESET */ + startup-delay-us = <70000>; + enable-active-high; + }; + + /* HS USB Host PHY on PORT 3 */ + hsusb3_phy: hsusb3_phy { + compatible = "usb-nop-xceiv"; + reset-supply = <&hsusb3_reset>; + }; + + leds { + compatible = "gpio-leds"; + led@1 { + label = "omap5:blue:usr1"; + gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */ + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + }; +}; + +&omap5_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &twl6040_pins + &mcpdm_pins + &dmic_pins + &mcbsp1_pins + &mcbsp2_pins + &usbhost_pins + &led_gpio_pins + >; + + twl6040_pins: pinmux_twl6040_pins { + pinctrl-single,pins = < + 0x18a (PIN_OUTPUT | MUX_MODE6) /* perslimbus2_clock.gpio5_145 */ + >; + }; + + mcpdm_pins: pinmux_mcpdm_pins { + pinctrl-single,pins = < + 0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ + 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */ + 0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */ + 0x160 (PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */ + 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */ + >; + }; + + dmic_pins: pinmux_dmic_pins { + pinctrl-single,pins = < + 0x144 (PIN_INPUT | MUX_MODE0) /* abedmic_din1.abedmic_din1 */ + 0x146 (PIN_INPUT | MUX_MODE0) /* abedmic_din2.abedmic_din2 */ + 0x148 (PIN_INPUT | MUX_MODE0) /* abedmic_din3.abedmic_din3 */ + 0x14a (PIN_OUTPUT | MUX_MODE0) /* abedmic_clk1.abedmic_clk1 */ + >; + }; + + mcbsp1_pins: pinmux_mcbsp1_pins { + pinctrl-single,pins = < + 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ + 0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */ + 0x150 (PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */ + 0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */ + >; + }; + + mcbsp2_pins: pinmux_mcbsp2_pins { + pinctrl-single,pins = < + 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */ + 0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */ + 0x158 (PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */ + 0x15a (PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ + 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ + >; + }; + + i2c5_pins: pinmux_i2c5_pins { + pinctrl-single,pins = < + 0x184 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */ + 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */ + >; + }; + + mcspi2_pins: pinmux_mcspi2_pins { + pinctrl-single,pins = < + 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ + 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ + 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ + 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs */ + >; + }; + + mcspi3_pins: pinmux_mcspi3_pins { + pinctrl-single,pins = < + 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */ + 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */ + 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */ + 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */ + >; + }; + + mcspi4_pins: pinmux_mcspi4_pins { + pinctrl-single,pins = < + 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */ + 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */ + 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */ + 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */ + >; + }; + + usbhost_pins: pinmux_usbhost_pins { + pinctrl-single,pins = < + 0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ + 0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */ + + 0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */ + 0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */ + + 0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */ + 0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */ + >; + }; + + led_gpio_pins: pinmux_led_gpio_pins { + pinctrl-single,pins = < + 0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */ + >; + }; + + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + 0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */ + 0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */ + 0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */ + 0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + 0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */ + 0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */ + >; + }; + + uart5_pins: pinmux_uart5_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */ + 0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */ + 0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */ + 0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */ + >; + }; + +}; + +&omap5_pmx_wkup { + pinctrl-names = "default"; + pinctrl-0 = < + &usbhost_wkup_pins + >; + + usbhost_wkup_pins: pinmux_usbhost_wkup_pins { + pinctrl-single,pins = < + 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */ + >; + }; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <4>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <8>; + ti,non-removable; +}; + +&mmc3 { + bus-width = <4>; + ti,non-removable; +}; + +&mmc4 { + status = "disabled"; +}; + +&mmc5 { + status = "disabled"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + + clock-frequency = <400000>; + + palmas: palmas@48 { + compatible = "ti,palmas"; + interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */ + interrupt-parent = <&gic>; + reg = <0x48>; + interrupt-controller; + #interrupt-cells = <2>; + + palmas_pmic { + compatible = "ti,palmas-pmic"; + interrupt-parent = <&palmas>; + interrupts = <14 IRQ_TYPE_NONE>; + interrupt-name = "short-irq"; + + ti,ldo6-vibrator; + + regulators { + smps123_reg: smps123 { + regulator-name = "smps123"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + smps45_reg: smps45 { + regulator-name = "smps45"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1310000>; + regulator-always-on; + regulator-boot-on; + }; + + smps6_reg: smps6 { + regulator-name = "smps6"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + smps7_reg: smps7 { + regulator-name = "smps7"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + smps8_reg: smps8 { + regulator-name = "smps8"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1310000>; + regulator-always-on; + regulator-boot-on; + }; + + smps9_reg: smps9 { + regulator-name = "smps9"; + regulator-min-microvolt = <2100000>; + regulator-max-microvolt = <2100000>; + regulator-always-on; + regulator-boot-on; + ti,smps-range = <0x80>; + }; + + smps10_reg: smps10 { + regulator-name = "smps10"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo1_reg: ldo1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo2_reg: ldo2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo3_reg: ldo3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo4_reg: ldo4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo5_reg: ldo5 { + regulator-name = "ldo5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo6_reg: ldo6 { + regulator-name = "ldo6"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo7_reg: ldo7 { + regulator-name = "ldo7"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo8_reg: ldo8 { + regulator-name = "ldo8"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo9_reg: ldo9 { + regulator-name = "ldo9"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + ldoln_reg: ldoln { + regulator-name = "ldoln"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldousb_reg: ldousb { + regulator-name = "ldousb"; + regulator-min-microvolt = <3250000>; + regulator-max-microvolt = <3250000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; + }; +}; + +&i2c5 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c5_pins>; + + clock-frequency = <400000>; +}; + +&mcbsp3 { + status = "disabled"; +}; + +&usbhshost { + port2-mode = "ehci-hsic"; + port3-mode = "ehci-hsic"; +}; + +&usbhsehci { + phys = <0 &hsusb2_phy &hsusb3_phy>; +}; + +&mcspi1 { + +}; + +&mcspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi2_pins>; +}; + +&mcspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi3_pins>; +}; + +&mcspi4 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi4_pins>; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&uart5_pins>; +}; |
