diff options
Diffstat (limited to 'Documentation')
20 files changed, 364 insertions, 24 deletions
diff --git a/Documentation/IPMI.txt b/Documentation/IPMI.txt index 31d1d658827f..c0d8788e75d3 100644 --- a/Documentation/IPMI.txt +++ b/Documentation/IPMI.txt @@ -587,7 +587,7 @@ used to control it: modprobe ipmi_watchdog timeout=<t> pretimeout=<t> action=<action type> preaction=<preaction type> preop=<preop type> start_now=x - nowayout=x ifnum_to_use=n + nowayout=x ifnum_to_use=n panic_wdt_timeout=<t> ifnum_to_use specifies which interface the watchdog timer should use. The default is -1, which means to pick the first one registered. @@ -597,7 +597,9 @@ is the amount of seconds before the reset that the pre-timeout panic will occur (if pretimeout is zero, then pretimeout will not be enabled). Note that the pretimeout is the time before the final timeout. So if the timeout is 50 seconds and the pretimeout is 10 seconds, then the pretimeout -will occur in 40 second (10 seconds before the timeout). +will occur in 40 second (10 seconds before the timeout). The panic_wdt_timeout +is the value of timeout which is set on kernel panic, in order to let actions +such as kdump to occur during panic. The action may be "reset", "power_cycle", or "power_off", and specifies what to do when the timer times out, and defaults to @@ -634,6 +636,7 @@ for configuring the watchdog: ipmi_watchdog.preop=<preop type> ipmi_watchdog.start_now=x ipmi_watchdog.nowayout=x + ipmi_watchdog.panic_wdt_timeout=<t> The options are the same as the module parameter options. diff --git a/Documentation/arm/keystone/Overview.txt b/Documentation/arm/keystone/Overview.txt index f17bc4c9dff9..400c0c270d2e 100644 --- a/Documentation/arm/keystone/Overview.txt +++ b/Documentation/arm/keystone/Overview.txt @@ -49,24 +49,6 @@ specified through DTS. Following are the DTS used:- The device tree documentation for the keystone machines are located at Documentation/devicetree/bindings/arm/keystone/keystone.txt -Known issues & workaround -------------------------- - -Some of the device drivers used on keystone are re-used from that from -DaVinci and other TI SoCs. These device drivers may use clock APIs directly. -Some of the keystone specific drivers such as netcp uses run time power -management API instead to enable clock. As this API has limitations on -keystone, following workaround is needed to boot Linux. - - Add 'clk_ignore_unused' to the bootargs env variable in u-boot. Otherwise - clock frameworks will try to disable clocks that are unused and disable - the hardware. This is because netcp related power domain and clock - domains are enabled in u-boot as run time power management API currently - doesn't enable clocks for netcp due to a limitation. This workaround is - expected to be removed in the future when proper API support becomes - available. Until then, this work around is needed. - - Document Author --------------- Murali Karicheri <m-karicheri2@ti.com> diff --git a/Documentation/block/null_blk.txt b/Documentation/block/null_blk.txt index 2f6c6ff7161d..d8880ca30af4 100644 --- a/Documentation/block/null_blk.txt +++ b/Documentation/block/null_blk.txt @@ -70,3 +70,6 @@ use_per_node_hctx=[0/1]: Default: 0 parameter. 1: The multi-queue block layer is instantiated with a hardware dispatch queue for each CPU node in the system. + +use_lightnvm=[0/1]: Default: 0 + Register device with LightNVM. Requires blk-mq to be used. diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt index 6b0f49f6f499..8608a776caa7 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt @@ -5,4 +5,11 @@ Boards with the BCM4708 SoC shall have the following properties: Required root node property: +bcm4708 compatible = "brcm,bcm4708"; + +bcm4709 +compatible = "brcm,bcm4709"; + +bcm53012 +compatible = "brcm,bcm53012"; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,nsp-cpu-method.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,nsp-cpu-method.txt new file mode 100644 index 000000000000..677ef9d9f445 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,nsp-cpu-method.txt @@ -0,0 +1,39 @@ +Broadcom Northstar Plus SoC CPU Enable Method +--------------------------------------------- +This binding defines the enable method used for starting secondary +CPU in the following Broadcom SoCs: + BCM58522, BCM58525, BCM58535, BCM58622, BCM58623, BCM58625, BCM88312 + +The enable method is specified by defining the following required +properties in the corresponding secondary "cpu" device tree node: + - enable-method = "brcm,bcm-nsp-smp"; + - secondary-boot-reg = <...>; + +The secondary-boot-reg property is a u32 value that specifies the +physical address of the register which should hold the common +entry point for a secondary CPU. This entry is cpu node specific +and should be added per cpu. E.g., in case of NSP (BCM58625) which +is a dual core CPU SoC, this entry should be added to cpu1 node. + + +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + next-level-cache = <&L2>; + reg = <0>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + next-level-cache = <&L2>; + enable-method = "brcm,bcm-nsp-smp"; + secondary-boot-reg = <0xffff042c>; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/compulab-boards.txt b/Documentation/devicetree/bindings/arm/compulab-boards.txt new file mode 100644 index 000000000000..71172d56875c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/compulab-boards.txt @@ -0,0 +1,5 @@ +CompuLab SB-SOM is a multi-module baseboard capable of carrying CM-T43, CM-T54, +and CM-QS600 modules with minor modifications to the SB-SOM assembly. + +Required root node properties: + - compatible = should be "compulab,sb-som" diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 3a07a87fef20..d1915549e009 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -190,6 +190,7 @@ nodes to be present and contain the properties described below. "allwinner,sun6i-a31" "allwinner,sun8i-a23" "arm,psci" + "brcm,bcm-nsp-smp" "brcm,brahma-b15" "marvell,armada-375-smp" "marvell,armada-380-smp" diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 9f4e5136e568..0b2c946a0289 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -138,9 +138,18 @@ Boards: - AM335X phyBOARD-WEGA: Single Board Computer dev kit compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx" +- AM335X CM-T335 : System On Module, built around the Sitara AM3352/4 + compatible = "compulab,cm-t335", "ti,am33xx" + - OMAP5 EVM : Evaluation Module compatible = "ti,omap5-evm", "ti,omap5" +- AM437x CM-T43 + compatible = "compulab,am437x-cm-t43", "ti,am4372", "ti,am43" + +- AM437x SBC-T43 + compatible = "compulab,am437x-sbc-t43", "compulab,am437x-cm-t43", "ti,am4372", "ti,am43" + - AM43x EPOS EVM compatible = "ti,am43x-epos-evm", "ti,am4372", "ti,am43" @@ -150,6 +159,12 @@ Boards: - AM437x SK EVM: AM437x StarterKit Evaluation Module compatible = "ti,am437x-sk-evm", "ti,am4372", "ti,am43" +- AM57XX CL-SOM-AM57x + compatible = "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" + +- AM57XX SBC-AM57x + compatible = "compulab,sbc-am57x", "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" + - DRA742 EVM: Software Development Board for DRA742 compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7" diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 8e985dd2f181..2fa0a213a0c1 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -35,6 +35,11 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "netxeon,r89", "rockchip,rk3288"; +- Google Brain (dev-board): + Required root node properties: + - compatible = "google,veyron-brain-rev0", "google,veyron-brain", + "google,veyron", "rockchip,rk3288"; + - Google Jaq (Haier Chromebook 11 and more): Required root node properties: - compatible = "google,veyron-jaq-rev5", "google,veyron-jaq-rev4", @@ -49,6 +54,15 @@ Rockchip platforms device tree bindings "google,veyron-jerry-rev3", "google,veyron-jerry", "google,veyron", "rockchip,rk3288"; +- Google Mickey (Asus Chromebit CS10): + Required root node properties: + - compatible = "google,veyron-mickey-rev8", "google,veyron-mickey-rev7", + "google,veyron-mickey-rev6", "google,veyron-mickey-rev5", + "google,veyron-mickey-rev4", "google,veyron-mickey-rev3", + "google,veyron-mickey-rev2", "google,veyron-mickey-rev1", + "google,veyron-mickey-rev0", "google,veyron-mickey", + "google,veyron", "rockchip,rk3288"; + - Google Minnie (Asus Chromebook Flip C100P): Required root node properties: - compatible = "google,veyron-minnie-rev4", "google,veyron-minnie-rev3", diff --git a/Documentation/devicetree/bindings/arm/scu.txt b/Documentation/devicetree/bindings/arm/scu.txt index c447680519bb..08a587875996 100644 --- a/Documentation/devicetree/bindings/arm/scu.txt +++ b/Documentation/devicetree/bindings/arm/scu.txt @@ -10,10 +10,13 @@ References: Revision r2p0 - Cortex-A5: see DDI0434B Cortex-A5 MPCore Technical Reference Manual Revision r0p1 +- ARM11 MPCore: see DDI0360F ARM 11 MPCore Processor Technical Reference + Manial Revision r2p0 - compatible : Should be: "arm,cortex-a9-scu" "arm,cortex-a5-scu" + "arm,arm11mp-scu" - reg : Specify the base address and the size of the SCU register window. diff --git a/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt b/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt new file mode 100644 index 000000000000..8b7177cecb36 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt @@ -0,0 +1,40 @@ +ARM System Controller ICST clocks + +The ICS525 and ICS307 oscillators are produced by Integrated Devices +Technology (IDT). ARM integrated these oscillators deeply into their +reference designs by adding special control registers that manage such +oscillators to their system controllers. + +The ARM system controller contains logic to serialize and initialize +an ICST clock request after a write to the 32 bit register at an offset +into the system controller. Furthermore, to even be able to alter one of +these frequencies, the system controller must first be unlocked by +writing a special token to another offset in the system controller. + +The ICST oscillator must be provided inside a system controller node. + +Required properties: +- lock-offset: the offset address into the system controller where the + unlocking register is located +- vco-offset: the offset address into the system controller where the + ICST control register is located (even 32 bit address) +- compatible: must be one of "arm,syscon-icst525" or "arm,syscon-icst307" +- #clock-cells: must be <0> +- clocks: parent clock, since the ICST needs a parent clock to derive its + frequency from, this attribute is compulsory. + +Example: + +syscon: syscon@10000000 { + compatible = "syscon"; + reg = <0x10000000 0x1000>; + + oscclk0: osc0@0c { + compatible = "arm,syscon-icst307"; + #clock-cells = <0>; + lock-offset = <0x20>; + vco-offset = <0x0c>; + clocks = <&xtal24mhz>; + }; + (...) +}; diff --git a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt index ede65a55e21b..0b35e71b39e8 100644 --- a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt +++ b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt @@ -208,3 +208,8 @@ These clock IDs are defined in: ch3_unused lcpll_ports 4 BCM_NS2_LCPLL_PORTS_CH3_UNUSED ch4_unused lcpll_ports 5 BCM_NS2_LCPLL_PORTS_CH4_UNUSED ch5_unused lcpll_ports 6 BCM_NS2_LCPLL_PORTS_CH5_UNUSED + +BCM63138 +-------- +PLL and leaf clock compatible strings for BCM63138 are: + "brcm,bcm63138-armpll" diff --git a/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.txt b/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.txt new file mode 100644 index 000000000000..70cd8d18d841 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.txt @@ -0,0 +1,4 @@ +Startek Electronic Technology Co. KD050C 5.0" WVGA TFT LCD panel + +Required properties: +- compatible: should be "startek,startek-kd050c" diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt index 4f05d208c95c..d18109657da6 100644 --- a/Documentation/devicetree/bindings/regulator/tps65217.txt +++ b/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -26,7 +26,11 @@ Example: ti,pmic-shutdown-controller; regulators { + #address-cells = <1>; + #size-cells = <0>; + dcdc1_reg: dcdc1 { + reg = <0>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <1800000>; regulator-boot-on; @@ -34,6 +38,7 @@ Example: }; dcdc2_reg: dcdc2 { + reg = <1>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -41,6 +46,7 @@ Example: }; dcdc3_reg: dcc3 { + reg = <2>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <1500000>; regulator-boot-on; @@ -48,6 +54,7 @@ Example: }; ldo1_reg: ldo1 { + reg = <3>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -55,6 +62,7 @@ Example: }; ldo2_reg: ldo2 { + reg = <4>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -62,6 +70,7 @@ Example: }; ldo3_reg: ldo3 { + reg = <5>; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -69,6 +78,7 @@ Example: }; ldo4_reg: ldo4 { + reg = <6>; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt new file mode 100644 index 000000000000..5cc82b8353d8 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt @@ -0,0 +1,104 @@ +Qualcomm Shared Memory Point 2 Point binding + +The Shared Memory Point to Point (SMP2P) protocol facilitates communication of +a single 32-bit value between two processors. Each value has a single writer +(the local side) and a single reader (the remote side). Values are uniquely +identified in the system by the directed edge (local processor ID to remote +processor ID) and a string identifier. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,smp2p" + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: one entry specifying the smp2p notification interrupt + +- qcom,ipc: + Usage: required + Value type: <prop-encoded-array> + Definition: three entries specifying the outgoing ipc bit used for + signaling the remote end of the smp2p edge: + - phandle to a syscon node representing the apcs registers + - u32 representing offset to the register within the syscon + - u32 representing the ipc bit within the register + +- qcom,smem: + Usage: required + Value type: <u32 array> + Definition: two identifiers of the inbound and outbound smem items used + for this edge + +- qcom,local-pid: + Usage: required + Value type: <u32> + Definition: specifies the identfier of the local endpoint of this edge + +- qcom,remote-pid: + Usage: required + Value type: <u32> + Definition: specifies the identfier of the remote endpoint of this edge + += SUBNODES +Each SMP2P pair contain a set of inbound and outbound entries, these are +described in subnodes of the smp2p device node. The node names are not +important. + +- qcom,entry-name: + Usage: required + Value type: <string> + Definition: specifies the name of this entry, for inbound entries this + will be used to match against the remotely allocated entry + and for outbound entries this name is used for allocating + entries + +- interrupt-controller: + Usage: required for incoming entries + Value type: <empty> + Definition: marks the entry as inbound; the node should be specified + as a two cell interrupt-controller as defined in + "../interrupt-controller/interrupts.txt" + If not specified this node will denote the outgoing entry + +- #interrupt-cells: + Usage: required for incoming entries + Value type: <u32> + Definition: must be 2 - denoting the bit in the entry and IRQ flags + +- #qcom,state-cells: + Usage: required for outgoing entries + Value type: <u32> + Definition: must be 1 - denoting the bit in the entry + += EXAMPLE +The following example shows the SMP2P setup with the wireless processor, +defined from the 8974 apps processor's point-of-view. It encompasses one +inbound and one outbound entry: + +wcnss-smp2p { + compatible = "qcom,smp2p"; + qcom,smem = <431>, <451>; + + interrupts = <0 143 1>; + + qcom,ipc = <&apcs 8 18>; + + qcom,local-pid = <0>; + qcom,remote-pid = <4>; + + wcnss_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + + #qcom,state-cells = <1>; + }; + + wcnss_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt new file mode 100644 index 000000000000..a6634c70850d --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt @@ -0,0 +1,104 @@ +Qualcomm Shared Memory State Machine + +The Shared Memory State Machine facilitates broadcasting of single bit state +information between the processors in a Qualcomm SoC. Each processor is +assigned 32 bits of state that can be modified. A processor can through a +matrix of bitmaps signal subscription of notifications upon changes to a +certain bit owned by a certain remote processor. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,smsm" + +- qcom,ipc-N: + Usage: required + Value type: <prop-encoded-array> + Definition: three entries specifying the outgoing ipc bit used for + signaling the N:th remote processor + - phandle to a syscon node representing the apcs registers + - u32 representing offset to the register within the syscon + - u32 representing the ipc bit within the register + +- qcom,local-host: + Usage: optional + Value type: <u32> + Definition: identifier of the local processor in the list of hosts, or + in other words specifier of the column in the subscription + matrix representing the local processor + defaults to host 0 + +- #address-cells: + Usage: required + Value type: <u32> + Definition: must be 1 + +- #size-cells: + Usage: required + Value type: <u32> + Definition: must be 0 + += SUBNODES +Each processor's state bits are described by a subnode of the smsm device node. +Nodes can either be flagged as an interrupt-controller to denote a remote +processor's state bits or the local processors bits. The node names are not +important. + +- reg: + Usage: required + Value type: <u32> + Definition: specifies the offset, in words, of the first bit for this + entry + +- #qcom,state-cells: + Usage: required for local entry + Value type: <u32> + Definition: must be 1 - denotes bit number + +- interrupt-controller: + Usage: required for remote entries + Value type: <empty> + Definition: marks the entry as a interrupt-controller and the state bits + to belong to a remote processor + +- #interrupt-cells: + Usage: required for remote entries + Value type: <u32> + Definition: must be 2 - denotes bit number and IRQ flags + +- interrupts: + Usage: required for remote entries + Value type: <prop-encoded-array> + Definition: one entry specifying remote IRQ used by the remote processor + to signal changes of its state bits + + += EXAMPLE +The following example shows the SMEM setup for controlling properties of the +wireless processor, defined from the 8974 apps processor's point-of-view. It +encompasses one outbound entry and the outgoing interrupt for the wireless +processor. + +smsm { + compatible = "qcom,smsm"; + + #address-cells = <1>; + #size-cells = <0>; + + qcom,ipc-3 = <&apcs 8 19>; + + apps_smsm: apps@0 { + reg = <0>; + + #qcom,state-cells = <1>; + }; + + wcnss_smsm: wcnss@7 { + reg = <7>; + interrupts = <0 144 1>; + + interrupt-controller; + #interrupt-cells = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt index b38200d2583a..0dfa60d88dd3 100644 --- a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt @@ -1,7 +1,9 @@ * Temperature Sensor ADC (TSADC) on rockchip SoCs Required properties: -- compatible : "rockchip,rk3288-tsadc" +- compatible : should be "rockchip,<name>-tsadc" + "rockchip,rk3288-tsadc": found on RK3288 SoCs + "rockchip,rk3368-tsadc": found on RK3368 SoCs - reg : physical base address of the controller and length of memory mapped region. - interrupts : The interrupt number to the cpu. The interrupt specifier format diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 55df1d444e9f..409b134b7f88 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -218,6 +218,7 @@ sony Sony Corporation spansion Spansion Inc. sprd Spreadtrum Communications Inc. st STMicroelectronics +startek Startek ste ST-Ericsson stericsson ST-Ericsson synology Synology, Inc. diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801 index 6a4b1af724f8..1bba38dd2637 100644 --- a/Documentation/i2c/busses/i2c-i801 +++ b/Documentation/i2c/busses/i2c-i801 @@ -32,6 +32,7 @@ Supported adapters: * Intel Sunrise Point-LP (PCH) * Intel DNV (SOC) * Intel Broxton (SOC) + * Intel Lewisburg (PCH) Datasheets: Publicly available at the Intel website On Intel Patsburg and later chipsets, both the normal host SMBus controller diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index f8aae632f02f..742f69d18fc8 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1583,9 +1583,6 @@ bytes respectively. Such letter suffixes can also be entirely omitted. hwp_only Only load intel_pstate on systems which support hardware P state control (HWP) if available. - no_acpi - Don't use ACPI processor performance control objects - _PSS and _PPC specified limits. intremap= [X86-64, Intel-IOMMU] on enable Interrupt Remapping (default) |
