diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/gpio/led.txt | 6 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/vendor-prefixes.txt | 1 | ||||
| -rw-r--r-- | Documentation/hwmon/jc42 | 26 | ||||
| -rw-r--r-- | Documentation/hwmon/w83627ehf | 9 | ||||
| -rw-r--r-- | Documentation/hwmon/zl6100 | 14 | ||||
| -rw-r--r-- | Documentation/input/alps.txt | 3 | ||||
| -rw-r--r-- | Documentation/kernel-parameters.txt | 6 |
7 files changed, 45 insertions, 20 deletions
diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt index 141087cf3107..fd2bd56e7195 100644 --- a/Documentation/devicetree/bindings/gpio/led.txt +++ b/Documentation/devicetree/bindings/gpio/led.txt @@ -7,9 +7,9 @@ Each LED is represented as a sub-node of the gpio-leds device. Each node's name represents the name of the corresponding LED. LED sub-node properties: -- gpios : Should specify the LED's GPIO, see "Specifying GPIO information - for devices" in Documentation/devicetree/booting-without-of.txt. Active - low LEDs should be indicated using flags in the GPIO specifier. +- gpios : Should specify the LED's GPIO, see "gpios property" in + Documentation/devicetree/gpio.txt. Active low LEDs should be + indicated using flags in the GPIO specifier. - label : (optional) The label for this LED. If omitted, the label is taken from the node name (excluding the unit address). - linux,default-trigger : (optional) This parameter, if present, is a diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index ecc6a6cd26c1..a20008ab319a 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -30,6 +30,7 @@ national National Semiconductor nintendo Nintendo nvidia NVIDIA nxp NXP Semiconductors +picochip Picochip Ltd powervr Imagination Technologies qcom Qualcomm, Inc. ramtron Ramtron International diff --git a/Documentation/hwmon/jc42 b/Documentation/hwmon/jc42 index a22ecf48f255..52729a756c1b 100644 --- a/Documentation/hwmon/jc42 +++ b/Documentation/hwmon/jc42 @@ -7,21 +7,29 @@ Supported chips: Addresses scanned: I2C 0x18 - 0x1f Datasheets: http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf - * IDT TSE2002B3, TS3000B3 - Prefix: 'tse2002b3', 'ts3000b3' + * Atmel AT30TS00 + Prefix: 'at30ts00' Addresses scanned: I2C 0x18 - 0x1f Datasheets: - http://www.idt.com/products/getdoc.cfm?docid=18715691 - http://www.idt.com/products/getdoc.cfm?docid=18715692 + http://www.atmel.com/Images/doc8585.pdf + * IDT TSE2002B3, TSE2002GB2, TS3000B3, TS3000GB2 + Prefix: 'tse2002', 'ts3000' + Addresses scanned: I2C 0x18 - 0x1f + Datasheets: + http://www.idt.com/sites/default/files/documents/IDT_TSE2002B3C_DST_20100512_120303152056.pdf + http://www.idt.com/sites/default/files/documents/IDT_TSE2002GB2A1_DST_20111107_120303145914.pdf + http://www.idt.com/sites/default/files/documents/IDT_TS3000B3A_DST_20101129_120303152013.pdf + http://www.idt.com/sites/default/files/documents/IDT_TS3000GB2A1_DST_20111104_120303151012.pdf * Maxim MAX6604 Prefix: 'max6604' Addresses scanned: I2C 0x18 - 0x1f Datasheets: http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf - * Microchip MCP9805, MCP98242, MCP98243, MCP9843 - Prefixes: 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843' + * Microchip MCP9804, MCP9805, MCP98242, MCP98243, MCP9843 + Prefixes: 'mcp9804', 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843' Addresses scanned: I2C 0x18 - 0x1f Datasheets: + http://ww1.microchip.com/downloads/en/DeviceDoc/22203C.pdf http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf @@ -48,6 +56,12 @@ Supported chips: Datasheets: http://www.st.com/stonline/products/literature/ds/13447/stts424.pdf http://www.st.com/stonline/products/literature/ds/13448/stts424e02.pdf + * ST Microelectronics STTS2002, STTS3000 + Prefix: 'stts2002', 'stts3000' + Addresses scanned: I2C 0x18 - 0x1f + Datasheets: + http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00225278.pdf + http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATA_BRIEF/CD00270920.pdf * JEDEC JC 42.4 compliant temperature sensor chips Prefix: 'jc42' Addresses scanned: I2C 0x18 - 0x1f diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf index 3f44dbdfda70..ceaf6f652b00 100644 --- a/Documentation/hwmon/w83627ehf +++ b/Documentation/hwmon/w83627ehf @@ -50,7 +50,7 @@ W83627DHG, W83627DHG-P, W83627UHG, W83667HG, W83667HG-B, W83667HG-I (NCT6775F), and NCT6776F super I/O chips. We will refer to them collectively as Winbond chips. -The chips implement 2 to 4 temperature sensors (9 for NCT6775F and NCT6776F), +The chips implement 3 to 4 temperature sensors (9 for NCT6775F and NCT6776F), 2 to 5 fan rotation speed sensors, 8 to 10 analog voltage sensors, one VID (except for 627UHG), alarms with beep warnings (control unimplemented), and some automatic fan regulation strategies (plus manual fan control mode). @@ -143,8 +143,13 @@ pwm[1-4]_min_output - minimum fan speed (range 1 - 255), when the temperature pwm[1-4]_stop_time - how many milliseconds [ms] must elapse to switch corresponding fan off. (when the temperature was below defined range). +pwm[1-4]_start_output-minimum fan speed (range 1 - 255) when spinning up +pwm[1-4]_step_output- rate of fan speed change (1 - 255) +pwm[1-4]_stop_output- minimum fan speed (range 1 - 255) when spinning down +pwm[1-4]_max_output - maximum fan speed (range 1 - 255), when the temperature + is above defined range. -Note: last two functions are influenced by other control bits, not yet exported +Note: last six functions are influenced by other control bits, not yet exported by the driver, so a change might not have any effect. Implementation Details diff --git a/Documentation/hwmon/zl6100 b/Documentation/hwmon/zl6100 index 51f76a189fee..a4e8d90f59f6 100644 --- a/Documentation/hwmon/zl6100 +++ b/Documentation/hwmon/zl6100 @@ -88,14 +88,12 @@ Module parameters delay ----- -Some Intersil/Zilker Labs DC-DC controllers require a minimum interval between -I2C bus accesses. According to Intersil, the minimum interval is 2 ms, though -1 ms appears to be sufficient and has not caused any problems in testing. -The problem is known to affect ZL6100, ZL2105, and ZL2008. It is known not to -affect ZL2004 and ZL6105. The driver automatically sets the interval to 1 ms -except for ZL2004 and ZL6105. To enable manual override, the driver provides a -writeable module parameter, 'delay', which can be used to set the interval to -a value between 0 and 65,535 microseconds. +Intersil/Zilker Labs DC-DC controllers require a minimum interval between I2C +bus accesses. According to Intersil, the minimum interval is 2 ms, though 1 ms +appears to be sufficient and has not caused any problems in testing. The problem +is known to affect all currently supported chips. For manual override, the +driver provides a writeable module parameter, 'delay', which can be used to set +the interval to a value between 0 and 65,535 microseconds. Sysfs entries diff --git a/Documentation/input/alps.txt b/Documentation/input/alps.txt index f274c28b5103..2f95308251d4 100644 --- a/Documentation/input/alps.txt +++ b/Documentation/input/alps.txt @@ -13,7 +13,8 @@ Detection All ALPS touchpads should respond to the "E6 report" command sequence: E8-E6-E6-E6-E9. An ALPS touchpad should respond with either 00-00-0A or -00-00-64. +00-00-64 if no buttons are pressed. The bits 0-2 of the first byte will be 1s +if some buttons are pressed. If the E6 report is successful, the touchpad model is identified using the "E7 report" sequence: E8-E7-E7-E7-E9. The response is the model signature and is diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 033d4e69b43b..d99fd9c0ec0e 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -2211,6 +2211,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted. default: off. + printk.always_kmsg_dump= + Trigger kmsg_dump for cases other than kernel oops or + panics + Format: <bool> (1/Y/y=enable, 0/N/n=disable) + default: disabled + printk.time= Show timing data prefixed to each printk message line Format: <bool> (1/Y/y=enable, 0/N/n=disable) |
