diff options
Diffstat (limited to 'Documentation/powerpc/dts-bindings')
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/can.txt | 53 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/dma.txt | 8 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/i2c.txt | 30 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/mpc5121-psc.txt | 70 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/mpc5200.txt | 9 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/spi.txt | 7 |
6 files changed, 161 insertions, 16 deletions
diff --git a/Documentation/powerpc/dts-bindings/fsl/can.txt b/Documentation/powerpc/dts-bindings/fsl/can.txt new file mode 100644 index 000000000000..2fa4fcd38fd6 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/can.txt @@ -0,0 +1,53 @@ +CAN Device Tree Bindings +------------------------ + +(c) 2006-2009 Secret Lab Technologies Ltd +Grant Likely <grant.likely@secretlab.ca> + +fsl,mpc5200-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock (XTAL) + "ref" is default in case this property is not + present. + +fsl,mpc5121-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source and divider shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock + "sys" for system clock + If this property is not present, an optimal CAN + clock source and frequency based on the system + clock will be selected. If this is not possible, + the reference clock will be used. + +- fsl,mscan-clock-divider: for the reference and system clock, an additional + clock divider can be specified. By default, a + value of 1 is used. + +Note that the MPC5121 Rev. 1 processor is not supported. + +Examples: + can@1300 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <12 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1300 0x80>; + }; + + can@1380 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <13 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1380 0x80>; + fsl,mscan-clock-source = "ref"; + fsl,mscan-clock-divider = <3>; + }; diff --git a/Documentation/powerpc/dts-bindings/fsl/dma.txt b/Documentation/powerpc/dts-bindings/fsl/dma.txt index 0732cdd05ba1..2a4b4bce6110 100644 --- a/Documentation/powerpc/dts-bindings/fsl/dma.txt +++ b/Documentation/powerpc/dts-bindings/fsl/dma.txt @@ -44,21 +44,29 @@ Example: compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; cell-index = <0>; reg = <0 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; cell-index = <1>; reg = <0x80 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; cell-index = <2>; reg = <0x100 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; cell-index = <3>; reg = <0x180 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; }; }; diff --git a/Documentation/powerpc/dts-bindings/fsl/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/i2c.txt index b6d2e21474f9..50da20310585 100644 --- a/Documentation/powerpc/dts-bindings/fsl/i2c.txt +++ b/Documentation/powerpc/dts-bindings/fsl/i2c.txt @@ -2,15 +2,14 @@ Required properties : - - device_type : Should be "i2c" - reg : Offset and length of the register set for the device + - compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a + compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121, + mpc5200 or mpc5200b. For the mpc5121, an additional node + "fsl,mpc5121-i2c-ctrl" is required as shown in the example below. Recommended properties : - - compatible : compatibility list with 2 entries, the first should - be "fsl,CHIP-i2c" where CHIP is the name of a compatible processor, - e.g. mpc8313, mpc8543, mpc8544, mpc5200 or mpc5200b. The second one - should be "fsl-i2c". - interrupts : <a b> where a is the interrupt number and b is a field that represents an encoding of the sense and level information for the interrupt. This should be encoded based on @@ -24,25 +23,40 @@ Recommended properties : Examples : + /* MPC5121 based board */ + i2c@1740 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5121-i2c", "fsl-i2c"; + reg = <0x1740 0x20>; + interrupts = <11 0x8>; + interrupt-parent = <&ipic>; + clock-frequency = <100000>; + }; + + i2ccontrol@1760 { + compatible = "fsl,mpc5121-i2c-ctrl"; + reg = <0x1760 0x8>; + }; + + /* MPC5200B based board */ i2c@3d00 { #address-cells = <1>; #size-cells = <0>; compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - cell-index = <0>; reg = <0x3d00 0x40>; interrupts = <2 15 0>; interrupt-parent = <&mpc5200_pic>; fsl,preserve-clocking; }; + /* MPC8544 base board */ i2c@3100 { #address-cells = <1>; #size-cells = <0>; - cell-index = <1>; compatible = "fsl,mpc8544-i2c", "fsl-i2c"; reg = <0x3100 0x100>; interrupts = <43 2>; interrupt-parent = <&mpic>; clock-frequency = <400000>; }; - diff --git a/Documentation/powerpc/dts-bindings/fsl/mpc5121-psc.txt b/Documentation/powerpc/dts-bindings/fsl/mpc5121-psc.txt new file mode 100644 index 000000000000..8832e8798912 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/mpc5121-psc.txt @@ -0,0 +1,70 @@ +MPC5121 PSC Device Tree Bindings + +PSC in UART mode +---------------- + +For PSC in UART mode the needed PSC serial devices +are specified by fsl,mpc5121-psc-uart nodes in the +fsl,mpc5121-immr SoC node. Additionally the PSC FIFO +Controller node fsl,mpc5121-psc-fifo is requered there: + +fsl,mpc5121-psc-uart nodes +-------------------------- + +Required properties : + - compatible : Should contain "fsl,mpc5121-psc-uart" and "fsl,mpc5121-psc" + - cell-index : Index of the PSC in hardware + - reg : Offset and length of the register set for the PSC device + - interrupts : <a b> where a is the interrupt number of the + PSC FIFO Controller and b is a field that represents an + encoding of the sense and level information for the interrupt. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Recommended properties : + - fsl,rx-fifo-size : the size of the RX fifo slice (a multiple of 4) + - fsl,tx-fifo-size : the size of the TX fifo slice (a multiple of 4) + + +fsl,mpc5121-psc-fifo node +------------------------- + +Required properties : + - compatible : Should be "fsl,mpc5121-psc-fifo" + - reg : Offset and length of the register set for the PSC + FIFO Controller + - interrupts : <a b> where a is the interrupt number of the + PSC FIFO Controller and b is a field that represents an + encoding of the sense and level information for the interrupt. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + + +Example for a board using PSC0 and PSC1 devices in serial mode: + +serial@11000 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <0>; + reg = <0x11000 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; +}; + +serial@11100 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <1>; + reg = <0x11100 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; +}; + +pscfifo@11f00 { + compatible = "fsl,mpc5121-psc-fifo"; + reg = <0x11f00 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; +}; diff --git a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt index 5c6602dbfdc2..4ccb2cd5df94 100644 --- a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt +++ b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt @@ -195,11 +195,4 @@ External interrupts: fsl,mpc5200-mscan nodes ----------------------- -In addition to the required compatible-, reg- and interrupt-properites, you can -also specify which clock source shall be used for the controller: - -- fsl,mscan-clock-source- a string describing the clock source. Valid values - are: "ip" for ip bus clock - "ref" for reference clock (XTAL) - "ref" is default in case this property is not - present. +See file can.txt in this directory. diff --git a/Documentation/powerpc/dts-bindings/fsl/spi.txt b/Documentation/powerpc/dts-bindings/fsl/spi.txt index e7d9a344c4f4..80510c018eea 100644 --- a/Documentation/powerpc/dts-bindings/fsl/spi.txt +++ b/Documentation/powerpc/dts-bindings/fsl/spi.txt @@ -13,6 +13,11 @@ Required properties: - interrupt-parent : the phandle for the interrupt controller that services interrupts for this device. +Optional properties: +- gpios : specifies the gpio pins to be used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child nodes. + If unspecified, a single SPI device without a chip select can be used. + Example: spi@4c0 { cell-index = <0>; @@ -21,4 +26,6 @@ Example: interrupts = <82 0>; interrupt-parent = <700>; mode = "cpu"; + gpios = <&gpio 18 1 // device reg=<0> + &gpio 19 1>; // device reg=<1> }; |
