summaryrefslogtreecommitdiffstats
path: root/Documentation/networking
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/networking')
-rw-r--r--Documentation/networking/netconsole.txt68
1 files changed, 68 insertions, 0 deletions
diff --git a/Documentation/networking/netconsole.txt b/Documentation/networking/netconsole.txt
index 1aaa7383e41d..3c2f2b328638 100644
--- a/Documentation/networking/netconsole.txt
+++ b/Documentation/networking/netconsole.txt
@@ -3,6 +3,10 @@ started by Ingo Molnar <mingo@redhat.com>, 2001.09.17
2.6 port and netpoll api by Matt Mackall <mpm@selenic.com>, Sep 9 2003
Please send bug reports to Matt Mackall <mpm@selenic.com>
+and Satyam Sharma <satyam.sharma@gmail.com>
+
+Introduction:
+=============
This module logs kernel printk messages over UDP allowing debugging of
problem where disk logging fails and serial consoles are impractical.
@@ -13,6 +17,9 @@ the specified interface as soon as possible. While this doesn't allow
capture of early kernel panics, it does capture most of the boot
process.
+Sender and receiver configuration:
+==================================
+
It takes a string configuration parameter "netconsole" in the
following format:
@@ -46,6 +53,67 @@ address.
The remote host can run either 'netcat -u -l -p <port>' or syslogd.
+Dynamic reconfiguration:
+========================
+
+Dynamic reconfigurability is a useful addition to netconsole that enables
+remote logging targets to be dynamically added, removed, or have their
+parameters reconfigured at runtime from a configfs-based userspace interface.
+[ Note that the parameters of netconsole targets that were specified/created
+from the boot/module option are not exposed via this interface, and hence
+cannot be modified dynamically. ]
+
+To include this feature, select CONFIG_NETCONSOLE_DYNAMIC when building the
+netconsole module (or kernel, if netconsole is built-in).
+
+Some examples follow (where configfs is mounted at the /sys/kernel/config
+mountpoint).
+
+To add a remote logging target (target names can be arbitrary):
+
+ cd /sys/kernel/config/netconsole/
+ mkdir target1
+
+Note that newly created targets have default parameter values (as mentioned
+above) and are disabled by default -- they must first be enabled by writing
+"1" to the "enabled" attribute (usually after setting parameters accordingly)
+as described below.
+
+To remove a target:
+
+ rmdir /sys/kernel/config/netconsole/othertarget/
+
+The interface exposes these parameters of a netconsole target to userspace:
+
+ enabled Is this target currently enabled? (read-write)
+ dev_name Local network interface name (read-write)
+ local_port Source UDP port to use (read-write)
+ remote_port Remote agent's UDP port (read-write)
+ local_ip Source IP address to use (read-write)
+ remote_ip Remote agent's IP address (read-write)
+ local_mac Local interface's MAC address (read-only)
+ remote_mac Remote agent's MAC address (read-write)
+
+The "enabled" attribute is also used to control whether the parameters of
+a target can be updated or not -- you can modify the parameters of only
+disabled targets (i.e. if "enabled" is 0).
+
+To update a target's parameters:
+
+ cat enabled # check if enabled is 1
+ echo 0 > enabled # disable the target (if required)
+ echo eth2 > dev_name # set local interface
+ echo 10.0.0.4 > remote_ip # update some parameter
+ echo cb:a9:87:65:43:21 > remote_mac # update more parameters
+ echo 1 > enabled # enable target again
+
+You can also update the local interface dynamically. This is especially
+useful if you want to use interfaces that have newly come up (and may not
+have existed when netconsole was loaded / initialized).
+
+Miscellaneous notes:
+====================
+
WARNING: the default target ethernet setting uses the broadcast
ethernet address to send packets, which can cause increased load on
other systems on the same ethernet segment.
OpenPOWER on IntegriCloud