diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 78 |
1 files changed, 71 insertions, 7 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index abeff96e9d46..bcecfaa1e770 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -284,6 +284,11 @@ and is between 256 and 4096 characters. It is defined in the file isolate - enable device isolation (each device, as far as possible, will get its own protection domain) + fullflush - enable flushing of IO/TLB entries when + they are unmapped. Otherwise they are + flushed before they will be reused, which + is a lot of faster + amd_iommu_size= [HW,X86-64] Define the size of the aperture for the AMD IOMMU driver. Possible values are: @@ -463,12 +468,6 @@ and is between 256 and 4096 characters. It is defined in the file Range: 0 - 8192 Default: 64 - disable_8254_timer - enable_8254_timer - [IA32/X86_64] Disable/Enable interrupt 0 timer routing - over the 8254 in addition to over the IO-APIC. The - kernel tries to set a sensible default. - hpet= [X86-32,HPET] option to control HPET usage Format: { enable (default) | disable | force } disable: disable HPET and use PIT instead @@ -659,11 +658,12 @@ and is between 256 and 4096 characters. It is defined in the file earlyprintk= [X86-32,X86-64,SH,BLACKFIN] earlyprintk=vga earlyprintk=serial[,ttySn[,baudrate]] + earlyprintk=dbgp Append ",keep" to not disable it when the real console takes over. - Only vga or serial at a time, not both. + Only vga or serial or usb debug port at a time. Currently only ttyS0 and ttyS1 are supported. @@ -798,6 +798,7 @@ and is between 256 and 4096 characters. It is defined in the file hlt [BUGS=ARM,SH] + i8042.debug [HW] Toggle i8042 debug mode i8042.direct [HW] Put keyboard port into non-translated mode i8042.dumbkbd [HW] Pretend that controller can only read data from keyboard and cannot control its state @@ -1022,6 +1023,10 @@ and is between 256 and 4096 characters. It is defined in the file (only serial suported for now) Format: <serial_device>[,baud] + kmac= [MIPS] korina ethernet MAC address. + Configure the RouterBoard 532 series on-chip + Ethernet adapter MAC address. + l2cr= [PPC] l3cr= [PPC] @@ -1234,6 +1239,29 @@ and is between 256 and 4096 characters. It is defined in the file or memmap=0x10000$0x18690000 + memory_corruption_check=0/1 [X86] + Some BIOSes seem to corrupt the first 64k of + memory when doing things like suspend/resume. + Setting this option will scan the memory + looking for corruption. Enabling this will + both detect corruption and prevent the kernel + from using the memory being corrupted. + However, its intended as a diagnostic tool; if + repeatable BIOS-originated corruption always + affects the same memory, you can use memmap= + to prevent the kernel from using that memory. + + memory_corruption_check_size=size [X86] + By default it checks for corruption in the low + 64k, making this memory unavailable for normal + use. Use this parameter to scan for + corruption in more or less memory. + + memory_corruption_check_period=seconds [X86] + By default it checks for corruption every 60 + seconds. Use this parameter to check at some + other rate. 0 disables periodic checking. + memtest= [KNL,X86] Enable memtest Format: <integer> range: 0,4 : pattern number @@ -1435,6 +1463,12 @@ and is between 256 and 4096 characters. It is defined in the file nolapic_timer [X86-32,APIC] Do not use the local APIC timer. + nox2apic [X86-64,APIC] Do not enable x2APIC mode. + + x2apic_phys [X86-64,APIC] Use x2apic physical mode instead of + default x2apic cluster mode on platforms + supporting x2apic. + noltlbs [PPC] Do not use large page/tlb entries for kernel lowmem mapping on PPC40x. @@ -1690,6 +1724,11 @@ and is between 256 and 4096 characters. It is defined in the file autoconfiguration. Ranges are in pairs (memory base and size). + dynamic_printk + Enables pr_debug()/dev_dbg() calls if + CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled. These can also + be switched on/off via <debugfs>/dynamic_printk/modules + print-fatal-signals= [KNL] debug: print fatal signals print-fatal-signals=1: print segfault info to @@ -1892,6 +1931,12 @@ and is between 256 and 4096 characters. It is defined in the file shapers= [NET] Maximal number of shapers. + show_msr= [x86] show boot-time MSR settings + Format: { <integer> } + Show boot-time (BIOS-initialized) MSR settings. + The parameter means the number of CPUs to show, + for example 1 means boot CPU only. + sim710= [SCSI,HW] See header of drivers/scsi/sim710.c. @@ -2218,6 +2263,25 @@ and is between 256 and 4096 characters. It is defined in the file autosuspended. Devices for which the delay is set to a negative value won't be autosuspended at all. + usbcore.usbfs_snoop= + [USB] Set to log all usbfs traffic (default 0 = off). + + usbcore.blinkenlights= + [USB] Set to cycle leds on hubs (default 0 = off). + + usbcore.old_scheme_first= + [USB] Start with the old device initialization + scheme (default 0 = off). + + usbcore.use_both_schemes= + [USB] Try the other device initialization scheme + if the first one fails (default 1 = enabled). + + usbcore.initial_descriptor_timeout= + [USB] Specifies timeout for the initial 64-byte + USB_REQ_GET_DESCRIPTOR request in milliseconds + (default 5000 = 5.0 seconds). + usbhid.mousepoll= [USBHID] The interval which mice are to be polled at. |
