diff options
Diffstat (limited to 'Documentation/devicetree')
33 files changed, 1024 insertions, 17 deletions
diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt index 49fc7ada929a..3545ea704b50 100644 --- a/Documentation/devicetree/bindings/arm/davinci/nand.txt +++ b/Documentation/devicetree/bindings/arm/davinci/nand.txt @@ -23,6 +23,9 @@ Recommended properties : - ti,davinci-nand-buswidth: buswidth 8 or 16 - ti,davinci-nand-use-bbt: use flash based bad block table support. +nand device bindings may contain additional sub-nodes describing +partitions of the address space. See partition.txt for more detail. + Example(da850 EVM ): nand_cs3@62000000 { compatible = "ti,davinci-nand"; @@ -35,4 +38,9 @@ nand_cs3@62000000 { ti,davinci-ecc-mode = "hw"; ti,davinci-ecc-bits = <4>; ti,davinci-nand-use-bbt; + + partition@180000 { + label = "ubifs"; + reg = <0x180000 0x7e80000>; + }; }; diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt index bd7ce120bc13..fc9ce6f1688c 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt @@ -54,7 +54,8 @@ PROPERTIES - compatible Usage: required Value type: <string> - Definition: Must include "fsl,sec-v4.0" + Definition: Must include "fsl,sec-v4.0". Also includes SEC + ERA versions (optional) with which the device is compatible. - #address-cells Usage: required @@ -106,7 +107,7 @@ PROPERTIES EXAMPLE crypto@300000 { - compatible = "fsl,sec-v4.0"; + compatible = "fsl,sec-v4.0", "fsl,sec-era-v2.0"; #address-cells = <1>; #size-cells = <1>; reg = <0x300000 0x10000>; diff --git a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt new file mode 100644 index 000000000000..b4fa934ae3a2 --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt @@ -0,0 +1,191 @@ +NVIDIA Tegra host1x + +Required properties: +- compatible: "nvidia,tegra<chip>-host1x" +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt outputs from the controller. +- #address-cells: The number of cells used to represent physical base addresses + in the host1x address space. Should be 1. +- #size-cells: The number of cells used to represent the size of an address + range in the host1x address space. Should be 1. +- ranges: The mapping of the host1x address space to the CPU address space. + +The host1x top-level node defines a number of children, each representing one +of the following host1x client modules: + +- mpe: video encoder + + Required properties: + - compatible: "nvidia,tegra<chip>-mpe" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + +- vi: video input + + Required properties: + - compatible: "nvidia,tegra<chip>-vi" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + +- epp: encoder pre-processor + + Required properties: + - compatible: "nvidia,tegra<chip>-epp" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + +- isp: image signal processor + + Required properties: + - compatible: "nvidia,tegra<chip>-isp" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + +- gr2d: 2D graphics engine + + Required properties: + - compatible: "nvidia,tegra<chip>-gr2d" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + +- gr3d: 3D graphics engine + + Required properties: + - compatible: "nvidia,tegra<chip>-gr3d" + - reg: Physical base address and length of the controller's registers. + +- dc: display controller + + Required properties: + - compatible: "nvidia,tegra<chip>-dc" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + + Each display controller node has a child node, named "rgb", that represents + the RGB output associated with the controller. It can take the following + optional properties: + - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection + - nvidia,edid: supplies a binary EDID blob + +- hdmi: High Definition Multimedia Interface + + Required properties: + - compatible: "nvidia,tegra<chip>-hdmi" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + - vdd-supply: regulator for supply voltage + - pll-supply: regulator for PLL + + Optional properties: + - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection + - nvidia,edid: supplies a binary EDID blob + +- tvo: TV encoder output + + Required properties: + - compatible: "nvidia,tegra<chip>-tvo" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + +- dsi: display serial interface + + Required properties: + - compatible: "nvidia,tegra<chip>-dsi" + - reg: Physical base address and length of the controller's registers. + +Example: + +/ { + ... + + host1x { + compatible = "nvidia,tegra20-host1x", "simple-bus"; + reg = <0x50000000 0x00024000>; + interrupts = <0 65 0x04 /* mpcore syncpt */ + 0 67 0x04>; /* mpcore general */ + + #address-cells = <1>; + #size-cells = <1>; + + ranges = <0x54000000 0x54000000 0x04000000>; + + mpe { + compatible = "nvidia,tegra20-mpe"; + reg = <0x54040000 0x00040000>; + interrupts = <0 68 0x04>; + }; + + vi { + compatible = "nvidia,tegra20-vi"; + reg = <0x54080000 0x00040000>; + interrupts = <0 69 0x04>; + }; + + epp { + compatible = "nvidia,tegra20-epp"; + reg = <0x540c0000 0x00040000>; + interrupts = <0 70 0x04>; + }; + + isp { + compatible = "nvidia,tegra20-isp"; + reg = <0x54100000 0x00040000>; + interrupts = <0 71 0x04>; + }; + + gr2d { + compatible = "nvidia,tegra20-gr2d"; + reg = <0x54140000 0x00040000>; + interrupts = <0 72 0x04>; + }; + + gr3d { + compatible = "nvidia,tegra20-gr3d"; + reg = <0x54180000 0x00040000>; + }; + + dc@54200000 { + compatible = "nvidia,tegra20-dc"; + reg = <0x54200000 0x00040000>; + interrupts = <0 73 0x04>; + + rgb { + status = "disabled"; + }; + }; + + dc@54240000 { + compatible = "nvidia,tegra20-dc"; + reg = <0x54240000 0x00040000>; + interrupts = <0 74 0x04>; + + rgb { + status = "disabled"; + }; + }; + + hdmi { + compatible = "nvidia,tegra20-hdmi"; + reg = <0x54280000 0x00040000>; + interrupts = <0 75 0x04>; + status = "disabled"; + }; + + tvo { + compatible = "nvidia,tegra20-tvo"; + reg = <0x542c0000 0x00040000>; + interrupts = <0 76 0x04>; + status = "disabled"; + }; + + dsi { + compatible = "nvidia,tegra20-dsi"; + reg = <0x54300000 0x00040000>; + status = "disabled"; + }; + }; + + ... +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt new file mode 100644 index 000000000000..8ce9cd2855b5 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt @@ -0,0 +1,27 @@ +Device tree bindings for i2c-cbus-gpio driver + +Required properties: + - compatible = "i2c-cbus-gpio"; + - gpios: clk, dat, sel + - #address-cells = <1>; + - #size-cells = <0>; + +Optional properties: + - child nodes conforming to i2c bus binding + +Example: + +i2c@0 { + compatible = "i2c-cbus-gpio"; + gpios = <&gpio 66 0 /* clk */ + &gpio 65 0 /* dat */ + &gpio 64 0 /* sel */ + >; + #address-cells = <1>; + #size-cells = <0>; + + retu-mfd: retu@1 { + compatible = "retu-mfd"; + reg = <0x1>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt new file mode 100644 index 000000000000..66709a825541 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt @@ -0,0 +1,81 @@ +GPIO-based I2C Bus Mux + +This binding describes an I2C bus multiplexer that uses GPIOs to +route the I2C signals. + + +-----+ +-----+ + | dev | | dev | + +------------+ +-----+ +-----+ + | SoC | | | + | | /--------+--------+ + | +------+ | +------+ child bus A, on GPIO value set to 0 + | | I2C |-|--| Mux | + | +------+ | +--+---+ child bus B, on GPIO value set to 1 + | | | \----------+--------+--------+ + | +------+ | | | | | + | | GPIO |-|-----+ +-----+ +-----+ +-----+ + | +------+ | | dev | | dev | | dev | + +------------+ +-----+ +-----+ +-----+ + +Required properties: +- compatible: i2c-mux-gpio +- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side + port is connected to. +- mux-gpios: list of gpios used to control the muxer +* Standard I2C mux properties. See mux.txt in this directory. +* I2C child bus nodes. See mux.txt in this directory. + +Optional properties: +- idle-state: value to set the muxer to when idle. When no value is + given, it defaults to the last value used. + +For each i2c child node, an I2C child bus will be created. They will +be numbered based on their order in the device tree. + +Whenever an access is made to a device on a child bus, the value set +in the revelant node's reg property will be output using the list of +GPIOs, the first in the list holding the least-significant value. + +If an idle state is defined, using the idle-state (optional) property, +whenever an access is not being made to a device on a child bus, the +GPIOs will be set according to the idle value. + +If an idle state is not defined, the most recently used value will be +left programmed into hardware whenever no access is being made to a +device on a child bus. + +Example: + i2cmux { + compatible = "i2c-mux-gpio"; + #address-cells = <1>; + #size-cells = <0>; + mux-gpios = <&gpio1 22 0 &gpio1 23 0>; + i2c-parent = <&i2c1>; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + ssd1307: oled@3c { + compatible = "solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7 1>; + reset-active-low; + }; + }; + + i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + pca9555: pca9555@20 { + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt index c15781f4dc8c..1637c298a1b3 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt @@ -1,7 +1,7 @@ Device tree configuration for i2c-ocores Required properties: -- compatible : "opencores,i2c-ocores" +- compatible : "opencores,i2c-ocores" or "aeroflexgaisler,i2cmst" - reg : bus address start and address range size of device - interrupts : interrupt number - clock-frequency : frequency of bus clock in Hz diff --git a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt index b6cb5a12c672..e9611ace8792 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt @@ -13,11 +13,17 @@ Required properties: - interrupts: interrupt number to the cpu. - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges. +Required for all cases except "samsung,s3c2440-hdmiphy-i2c": + - Samsung GPIO variant (deprecated): + - gpios: The order of the gpios should be the following: <SDA, SCL>. + The gpio specifier depends on the gpio controller. Required in all + cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output + lines are permanently wired to the respective clienta + - Pinctrl variant (preferred, if available): + - pinctrl-0: Pin control group to be used for this controller. + - pinctrl-names: Should contain only one value - "default". + Optional properties: - - gpios: The order of the gpios should be the following: <SDA, SCL>. - The gpio specifier depends on the gpio controller. Required in all - cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output - lines are permanently wired to the respective client - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not specified, default value is 0. - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not @@ -31,8 +37,14 @@ Example: interrupts = <345>; samsung,i2c-sda-delay = <100>; samsung,i2c-max-bus-freq = <100000>; + /* Samsung GPIO variant begins here */ gpios = <&gpd1 2 0 /* SDA */ &gpd1 3 0 /* SCL */>; + /* Samsung GPIO variant ends here */ + /* Pinctrl variant begins here */ + pinctrl-0 = <&i2c3_bus>; + pinctrl-names = "default"; + /* Pinctrl variant ends here */ #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt b/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt new file mode 100644 index 000000000000..ead641c65e0a --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt @@ -0,0 +1,46 @@ +* GPIO driven matrix keypad device tree bindings + +GPIO driven matrix keypad is used to interface a SoC with a matrix keypad. +The matrix keypad supports multiple row and column lines, a key can be +placed at each intersection of a unique row and a unique column. The matrix +keypad can sense a key-press and key-release by means of GPIO lines and +report the event using GPIO interrupts to the cpu. + +Required Properties: +- compatible: Should be "gpio-matrix-keypad" +- row-gpios: List of gpios used as row lines. The gpio specifier + for this property depends on the gpio controller to + which these row lines are connected. +- col-gpios: List of gpios used as column lines. The gpio specifier + for this property depends on the gpio controller to + which these column lines are connected. +- linux,keymap: The definition can be found at + bindings/input/matrix-keymap.txt + +Optional Properties: +- linux,no-autorepeat: do no enable autorepeat feature. +- linux,wakeup: use any event on keypad as wakeup event. +- debounce-delay-ms: debounce interval in milliseconds +- col-scan-delay-us: delay, measured in microseconds, that is needed + before we can scan keypad after activating column gpio + +Example: + matrix-keypad { + compatible = "gpio-matrix-keypad"; + debounce-delay-ms = <5>; + col-scan-delay-us = <2>; + + row-gpios = <&gpio2 25 0 + &gpio2 26 0 + &gpio2 27 0>; + + col-gpios = <&gpio2 21 0 + &gpio2 22 0>; + + linux,keymap = <0x0000008B + 0x0100009E + 0x02000069 + 0x0001006A + 0x0101001C + 0x0201006C>; + }; diff --git a/Documentation/devicetree/bindings/input/pwm-beeper.txt b/Documentation/devicetree/bindings/input/pwm-beeper.txt new file mode 100644 index 000000000000..be332ae4f2d6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/pwm-beeper.txt @@ -0,0 +1,7 @@ +* PWM beeper device tree bindings + +Registers a PWM device as beeper. + +Required properties: +- compatible: should be "pwm-beeper" +- pwms: phandle to the physical PWM device diff --git a/Documentation/devicetree/bindings/input/stmpe-keypad.txt b/Documentation/devicetree/bindings/input/stmpe-keypad.txt new file mode 100644 index 000000000000..1b97222e8a0b --- /dev/null +++ b/Documentation/devicetree/bindings/input/stmpe-keypad.txt @@ -0,0 +1,39 @@ +* STMPE Keypad + +Required properties: + - compatible : "st,stmpe-keypad" + - linux,keymap : See ./matrix-keymap.txt + +Optional properties: + - debounce-interval : Debouncing interval time in milliseconds + - st,scan-count : Scanning cycles elapsed before key data is updated + - st,no-autorepeat : If specified device will not autorepeat + +Example: + + stmpe_keypad { + compatible = "st,stmpe-keypad"; + + debounce-interval = <64>; + st,scan-count = <8>; + st,no-autorepeat; + + linux,keymap = <0x205006b + 0x4010074 + 0x3050072 + 0x1030004 + 0x502006a + 0x500000a + 0x5008b + 0x706001c + 0x405000b + 0x6070003 + 0x3040067 + 0x303006c + 0x60400e7 + 0x602009e + 0x4020073 + 0x5050002 + 0x4030069 + 0x3020008>; + }; diff --git a/Documentation/devicetree/bindings/input/tca8418_keypad.txt b/Documentation/devicetree/bindings/input/tca8418_keypad.txt new file mode 100644 index 000000000000..2a1538f0053f --- /dev/null +++ b/Documentation/devicetree/bindings/input/tca8418_keypad.txt @@ -0,0 +1,8 @@ + +Required properties: +- compatible: "ti,tca8418" +- reg: the I2C address +- interrupts: IRQ line number, should trigger on falling edge +- keypad,num-rows: The number of rows +- keypad,num-columns: The number of columns +- linux,keymap: Keys definitions, see keypad-matrix. diff --git a/Documentation/devicetree/bindings/input/touchscreen/mms114.txt b/Documentation/devicetree/bindings/input/touchscreen/mms114.txt new file mode 100644 index 000000000000..89d4c56c5671 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/mms114.txt @@ -0,0 +1,34 @@ +* MELFAS MMS114 touchscreen controller + +Required properties: +- compatible: must be "melfas,mms114" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Optional properties: +- contact-threshold: +- moving-threshold: +- x-invert: invert X axis +- y-invert: invert Y axis + +Example: + + i2c@00000000 { + /* ... */ + + touchscreen@48 { + compatible = "melfas,mms114"; + reg = <0x48>; + interrupts = <39 0>; + x-size = <720>; + y-size = <1280>; + contact-threshold = <10>; + moving-threshold = <10>; + x-invert; + y-invert; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt new file mode 100644 index 000000000000..127baa31a77a --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt @@ -0,0 +1,43 @@ +STMPE Touchscreen +---------------- + +Required properties: + - compatible: "st,stmpe-ts" + +Optional properties: +- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 -> + 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6 + -> 144 clocks), recommended is 4. +- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC) +- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external + reference) +- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz) +- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 + samples, 3 -> 8 samples) +- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 -> + 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended + is 3 +- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 + -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2 +- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of + the fractional part) recommended is 7 +- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35 + mA max, 1 -> 50 mA typical 80 mA max) + +Node name must be stmpe_touchscreen and should be child node of stmpe node to +which it belongs. + +Example: + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + st,sample-time = <4>; + st,mod-12b = <1>; + st,ref-sel = <0>; + st,adc-freq = <1>; + st,ave-ctrl = <1>; + st,touch-det-delay = <2>; + st,settling = <2>; + st,fraction-z = <7>; + st,i-drive = <1>; + }; diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt new file mode 100644 index 000000000000..56edb5520685 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -0,0 +1,28 @@ +* ST Microelectronics STMPE Multi-Functional Device + +STMPE is an MFD device which may expose the following inbuilt devices: gpio, +keypad, touchscreen, adc, pwm, rotator. + +Required properties: + - compatible : "st,stmpe[610|801|811|1601|2401|2403]" + - reg : I2C/SPI address of the device + +Optional properties: + - interrupts : The interrupt outputs from the controller + - interrupt-controller : Marks the device node as an interrupt controller + - interrupt-parent : Specifies which IRQ controller we're connected to + - wakeup-source : Marks the input device as wakable + - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 + +Example: + + stmpe1601: stmpe1601@40 { + compatible = "st,stmpe1601"; + reg = <0x40>; + interrupts = <26 0x4>; + interrupt-parent = <&gpio6>; + interrupt-controller; + + wakeup-source; + st,autosleep-timeout = <1024>; + }; diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt new file mode 100644 index 000000000000..b04d03a1d499 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt @@ -0,0 +1,23 @@ +* Denali NAND controller + +Required properties: + - compatible : should be "denali,denali-nand-dt" + - reg : should contain registers location and length for data and reg. + - reg-names: Should contain the reg names "nand_data" and "denali_reg" + - interrupts : The interrupt number. + - dm-mask : DMA bit mask + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Examples: + +nand: nand@ff900000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "denali,denali-nand-dt"; + reg = <0xff900000 0x100000>, <0xffb80000 0x10000>; + reg-names = "nand_data", "denali_reg"; + interrupts = <0 144 4>; + dma-mask = <0xffffffff>; +}; diff --git a/Documentation/devicetree/bindings/mtd/flctl-nand.txt b/Documentation/devicetree/bindings/mtd/flctl-nand.txt new file mode 100644 index 000000000000..427f46dc60ad --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/flctl-nand.txt @@ -0,0 +1,49 @@ +FLCTL NAND controller + +Required properties: +- compatible : "renesas,shmobile-flctl-sh7372" +- reg : Address range of the FLCTL +- interrupts : flste IRQ number +- nand-bus-width : bus width to NAND chip + +Optional properties: +- dmas: DMA specifier(s) +- dma-names: name for each DMA specifier. Valid names are + "data_tx", "data_rx", "ecc_tx", "ecc_rx" + +The DMA fields are not used yet in the driver but are listed here for +completing the bindings. + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Example: + + flctl@e6a30000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "renesas,shmobile-flctl-sh7372"; + reg = <0xe6a30000 0x100>; + interrupts = <0x0d80>; + + nand-bus-width = <16>; + + dmas = <&dmac 1 /* data_tx */ + &dmac 2;> /* data_rx */ + dma-names = "data_tx", "data_rx"; + + system@0 { + label = "system"; + reg = <0x0 0x8000000>; + }; + + userdata@8000000 { + label = "userdata"; + reg = <0x8000000 0x10000000>; + }; + + cache@18000000 { + label = "cache"; + reg = <0x18000000 0x8000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt index e2c663b354d2..e3ea32e7de3e 100644 --- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt @@ -3,9 +3,7 @@ Required properties: - compatible : "st,spear600-fsmc-nand" - reg : Address range of the mtd chip -- reg-names: Should contain the reg names "fsmc_regs" and "nand_data" -- st,ale-off : Chip specific offset to ALE -- st,cle-off : Chip specific offset to CLE +- reg-names: Should contain the reg names "fsmc_regs", "nand_data", "nand_addr" and "nand_cmd" Optional properties: - bank-width : Width (in bytes) of the device. If not present, the width @@ -19,10 +17,10 @@ Example: #address-cells = <1>; #size-cells = <1>; reg = <0xd1800000 0x1000 /* FSMC Register */ - 0xd2000000 0x4000>; /* NAND Base */ - reg-names = "fsmc_regs", "nand_data"; - st,ale-off = <0x20000>; - st,cle-off = <0x10000>; + 0xd2000000 0x0010 /* NAND Base DATA */ + 0xd2020000 0x0010 /* NAND Base ADDR */ + 0xd2010000 0x0010>; /* NAND Base CMD */ + reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd"; bank-width = <1>; nand-skip-bbtscan; diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/m25p80.txt new file mode 100644 index 000000000000..6d3d57609470 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/m25p80.txt @@ -0,0 +1,29 @@ +* MTD SPI driver for ST M25Pxx (and similar) serial flash chips + +Required properties: +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. +- compatible : Should be the manufacturer and the name of the chip. Bear in mind + the DT binding is not Linux-only, but in case of Linux, see the + "m25p_ids" table in drivers/mtd/devices/m25p80.c for the list of + supported chips. +- reg : Chip-Select number +- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at + +Optional properties: +- m25p,fast-read : Use the "fast read" opcode to read data from the chip instead + of the usual "read" opcode. This opcode is not supported by + all chips and support for it can not be detected at runtime. + Refer to your chips' datasheet to check if this is supported + by your chip. + +Example: + + flash: m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,m25p80"; + reg = <0>; + spi-max-frequency = <40000000>; + m25p,fast-read; + }; diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index 94de19b8f16b..dab7847fc800 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -23,6 +23,9 @@ file systems on embedded devices. unaligned accesses as implemented in the JFFS2 code via memcpy(). By defining "no-unaligned-direct-access", the flash will not be exposed directly to the MTD users (e.g. JFFS2) any more. + - linux,mtd-name: allow to specify the mtd name for retro capability with + physmap-flash drivers as boot loader pass the mtd partition via the old + device name physmap-flash. For JEDEC compatible devices, the following additional properties are defined: diff --git a/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt b/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt new file mode 100644 index 000000000000..4ad29b9ac2ac --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt @@ -0,0 +1,81 @@ +* Freescale 85xx RAID Engine nodes + +RAID Engine nodes are defined to describe on-chip RAID accelerators. Each RAID +Engine should have a separate node. + +Supported chips: +P5020, P5040 + +Required properties: + +- compatible: Should contain "fsl,raideng-v1.0" as the value + This identifies RAID Engine block. 1 in 1.0 represents + major number whereas 0 represents minor number. The + version matches the hardware IP version. +- reg: offset and length of the register set for the device +- ranges: standard ranges property specifying the translation + between child address space and parent address space + +Example: + /* P5020 */ + raideng: raideng@320000 { + compatible = "fsl,raideng-v1.0"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x320000 0x10000>; + ranges = <0 0x320000 0x10000>; + }; + + +There must be a sub-node for each job queue present in RAID Engine +This node must be a sub-node of the main RAID Engine node + +- compatible: Should contain "fsl,raideng-v1.0-job-queue" as the value + This identifies the job queue interface +- reg: offset and length of the register set for job queue +- ranges: standard ranges property specifying the translation + between child address space and parent address space + +Example: + /* P5020 */ + raideng_jq0@1000 { + compatible = "fsl,raideng-v1.0-job-queue"; + reg = <0x1000 0x1000>; + ranges = <0x0 0x1000 0x1000>; + }; + + +There must be a sub-node for each job ring present in RAID Engine +This node must be a sub-node of job queue node + +- compatible: Must contain "fsl,raideng-v1.0-job-ring" as the value + This identifies job ring. Should contain either + "fsl,raideng-v1.0-hp-ring" or "fsl,raideng-v1.0-lp-ring" + depending upon whether ring has high or low priority +- reg: offset and length of the register set for job ring +- interrupts: interrupt mapping for job ring IRQ + +Optional property: + +- fsl,liodn: Specifies the LIODN to be used for Job Ring. This + property is normally set by firmware. Value + is of 12-bits which is the LIODN number for this JR. + This property is used by the IOMMU (PAMU) to distinquish + transactions from this JR and than be able to do address + translation & protection accordingly. + +Example: + /* P5020 */ + raideng_jq0@1000 { + compatible = "fsl,raideng-v1.0-job-queue"; + reg = <0x1000 0x1000>; + ranges = <0x0 0x1000 0x1000>; + + raideng_jr0: jr@0 { + compatible = "fsl,raideng-v1.0-job-ring", "fsl,raideng-v1.0-hp-ring"; + reg = <0x0 0x400>; + interrupts = <139 2 0 0>; + interrupt-parent = <&mpic>; + fsl,liodn = <0x41>; + }; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt new file mode 100644 index 000000000000..131e8c11d26f --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt @@ -0,0 +1,23 @@ +TI SOC ECAP based APWM controller + +Required properties: +- compatible: Must be "ti,am33xx-ecap" +- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. + First cell specifies the per-chip index of the PWM to use, the second + cell is the period in nanoseconds and bit 0 in the third cell is used to + encode the polarity of PWM output. Set bit 0 of the third in PWM specifier + to 1 for inverse polarity & set to 0 for normal polarity. +- reg: physical base address and size of the registers map. + +Optional properties: +- ti,hwmods: Name of the hwmod associated to the ECAP: + "ecap<x>", <x> being the 0-based instance number from the HW spec + +Example: + +ecap0: ecap@0 { + compatible = "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x48300100 0x80>; + ti,hwmods = "ecap0"; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt new file mode 100644 index 000000000000..4fc7079d822e --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt @@ -0,0 +1,23 @@ +TI SOC EHRPWM based PWM controller + +Required properties: +- compatible : Must be "ti,am33xx-ehrpwm" +- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. + First cell specifies the per-chip index of the PWM to use, the second + cell is the period in nanoseconds and bit 0 in the third cell is used to + encode the polarity of PWM output. Set bit 0 of the third in PWM specifier + to 1 for inverse polarity & set to 0 for normal polarity. +- reg: physical base address and size of the registers map. + +Optional properties: +- ti,hwmods: Name of the hwmod associated to the EHRPWM: + "ehrpwm<x>", <x> being the 0-based instance number from the HW spec + +Example: + +ehrpwm0: ehrpwm@0 { + compatible = "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x48300200 0x100>; + ti,hwmods = "ehrpwm0"; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt new file mode 100644 index 000000000000..f7eae77f8354 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt @@ -0,0 +1,31 @@ +TI SOC based PWM Subsystem + +Required properties: +- compatible: Must be "ti,am33xx-pwmss"; +- reg: physical base address and size of the registers map. +- address-cells: Specify the number of u32 entries needed in child nodes. + Should set to 1. +- size-cells: specify number of u32 entries needed to specify child nodes size + in reg property. Should set to 1. +- ranges: describes the address mapping of a memory-mapped bus. Should set to + physical address map of child's base address, physical address within + parent's address space and length of the address map. For am33xx, + 3 set of child register maps present, ECAP register space, EQEP + register space, EHRPWM register space. + +Also child nodes should also populated under PWMSS DT node. + +Example: +pwmss0: pwmss@48300000 { + compatible = "ti,am33xx-pwmss"; + reg = <0x48300000 0x10>; + ti,hwmods = "epwmss0"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + ranges = <0x48300100 0x48300100 0x80 /* ECAP */ + 0x48300180 0x48300180 0x80 /* EQEP */ + 0x48300200 0x48300200 0x80>; /* EHRPWM */ + + /* child nodes go here */ +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm.txt b/Documentation/devicetree/bindings/pwm/pwm.txt index 73ec962bfe8c..06e67247859a 100644 --- a/Documentation/devicetree/bindings/pwm/pwm.txt +++ b/Documentation/devicetree/bindings/pwm/pwm.txt @@ -37,10 +37,21 @@ device: pwm-names = "backlight"; }; +Note that in the example above, specifying the "pwm-names" is redundant +because the name "backlight" would be used as fallback anyway. + pwm-specifier typically encodes the chip-relative PWM number and the PWM -period in nanoseconds. Note that in the example above, specifying the -"pwm-names" is redundant because the name "backlight" would be used as -fallback anyway. +period in nanoseconds. + +Optionally, the pwm-specifier can encode a number of flags in a third cell: +- bit 0: PWM signal polarity (0: normal polarity, 1: inverse polarity) + +Example with optional PWM specifier for inverse polarity + + bl: backlight { + pwms = <&pwm 0 5000000 1>; + pwm-names = "backlight"; + }; 2) PWM controller nodes ----------------------- diff --git a/Documentation/devicetree/bindings/pwm/spear-pwm.txt b/Documentation/devicetree/bindings/pwm/spear-pwm.txt new file mode 100644 index 000000000000..3ac779d83386 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/spear-pwm.txt @@ -0,0 +1,18 @@ +== ST SPEAr SoC PWM controller == + +Required properties: +- compatible: should be one of: + - "st,spear320-pwm" + - "st,spear1340-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: number of cells used to specify PWM which is fixed to 2 on + SPEAr. The first cell specifies the per-chip index of the PWM to use and + the second cell is the period in nanoseconds. + +Example: + + pwm: pwm@a8000000 { + compatible ="st,spear320-pwm"; + reg = <0xa8000000 0x1000>; + #pwm-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt new file mode 100644 index 000000000000..2943ee5fce00 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt @@ -0,0 +1,17 @@ +Texas Instruments TWL series PWM drivers + +Supported PWMs: +On TWL4030 series: PWM1 and PWM2 +On TWL6030 series: PWM0 and PWM1 + +Required properties: +- compatible: "ti,twl4030-pwm" or "ti,twl6030-pwm" +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. + +Example: + +twl_pwm: pwm { + compatible = "ti,twl6030-pwm"; + #pwm-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt new file mode 100644 index 000000000000..cb64f3acc10f --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt @@ -0,0 +1,17 @@ +Texas Instruments TWL series PWM drivers connected to LED terminals + +Supported PWMs: +On TWL4030 series: PWMA and PWMB (connected to LEDA and LEDB terminals) +On TWL6030 series: LED PWM (mainly used as charging indicator LED) + +Required properties: +- compatible: "ti,twl4030-pwmled" or "ti,twl6030-pwmled" +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. + +Example: + +twl_pwmled: pwmled { + compatible = "ti,twl6030-pwmled"; + #pwm-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt new file mode 100644 index 000000000000..bcc63678a9a5 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt @@ -0,0 +1,17 @@ +VIA/Wondermedia VT8500/WM8xxx series SoC PWM controller + +Required properties: +- compatible: should be "via,vt8500-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. +- clocks: phandle to the PWM source clock + +Example: + +pwm1: pwm@d8220000 { + #pwm-cells = <2>; + compatible = "via,vt8500-pwm"; + reg = <0xd8220000 0x1000>; + clocks = <&clkpwm>; +}; diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt index d316fb895daf..4f05d208c95c 100644 --- a/Documentation/devicetree/bindings/regulator/tps65217.txt +++ b/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -11,6 +11,9 @@ Required properties: using the standard binding for regulators found at Documentation/devicetree/bindings/regulator/regulator.txt. +Optional properties: +- ti,pmic-shutdown-controller: Telling the PMIC to shutdown on PWR_EN toggle. + The valid names for regulators are: tps65217: dcdc1, dcdc2, dcdc3, ldo1, ldo2, ldo3 and ldo4 @@ -20,6 +23,7 @@ Example: tps: tps@24 { compatible = "ti,tps65217"; + ti,pmic-shutdown-controller; regulators { dcdc1_reg: dcdc1 { diff --git a/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt b/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt new file mode 100644 index 000000000000..c9d80d7da141 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt @@ -0,0 +1,17 @@ +* i.MX25 Real Time Clock controller + +This binding supports the following chips: i.MX25, i.MX53 + +Required properties: +- compatible: should be: "fsl,imx25-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: rtc alarm interrupt + +Example: + +rtc@80056000 { + compatible = "fsl,imx53-rtc", "fsl,imx25-rtc"; + reg = <0x80056000 2000>; + interrupts = <29>; +}; diff --git a/Documentation/devicetree/bindings/rtc/rtc-omap.txt b/Documentation/devicetree/bindings/rtc/rtc-omap.txt new file mode 100644 index 000000000000..b47aa415c820 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-omap.txt @@ -0,0 +1,17 @@ +TI Real Time Clock + +Required properties: +- compatible: "ti,da830-rtc" +- reg: Address range of rtc register set +- interrupts: rtc timer, alarm interrupts in order +- interrupt-parent: phandle for the interrupt controller + +Example: + +rtc@1c23000 { + compatible = "ti,da830-rtc"; + reg = <0x23000 0x1000>; + interrupts = <19 + 19>; + interrupt-parent = <&intc>; +}; diff --git a/Documentation/devicetree/bindings/video/exynos_dp.txt b/Documentation/devicetree/bindings/video/exynos_dp.txt new file mode 100644 index 000000000000..c60da67a5d76 --- /dev/null +++ b/Documentation/devicetree/bindings/video/exynos_dp.txt @@ -0,0 +1,80 @@ +The Exynos display port interface should be configured based on +the type of panel connected to it. + +We use two nodes: + -dp-controller node + -dptx-phy node(defined inside dp-controller node) + +For the DP-PHY initialization, we use the dptx-phy node. +Required properties for dptx-phy: + -reg: + Base address of DP PHY register. + -samsung,enable-mask: + The bit-mask used to enable/disable DP PHY. + +For the Panel initialization, we read data from dp-controller node. +Required properties for dp-controller: + -compatible: + should be "samsung,exynos5-dp". + -reg: + physical base address of the controller and length + of memory mapped region. + -interrupts: + interrupt combiner values. + -interrupt-parent: + phandle to Interrupt combiner node. + -samsung,color-space: + input video data format. + COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2 + -samsung,dynamic-range: + dynamic range for input video data. + VESA = 0, CEA = 1 + -samsung,ycbcr-coeff: + YCbCr co-efficients for input video. + COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1 + -samsung,color-depth: + number of bits per colour component. + COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3 + -samsung,link-rate: + link rate supported by the panel. + LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A + -samsung,lane-count: + number of lanes supported by the panel. + LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4 + +Optional properties for dp-controller: + -interlaced: + interlace scan mode. + Progressive if defined, Interlaced if not defined + -vsync-active-high: + VSYNC polarity configuration. + High if defined, Low if not defined + -hsync-active-high: + HSYNC polarity configuration. + High if defined, Low if not defined + +Example: + +SOC specific portion: + dp-controller { + compatible = "samsung,exynos5-dp"; + reg = <0x145b0000 0x10000>; + interrupts = <10 3>; + interrupt-parent = <&combiner>; + + dptx-phy { + reg = <0x10040720>; + samsung,enable-mask = <1>; + }; + + }; + +Board Specific portion: + dp-controller { + samsung,color-space = <0>; + samsung,dynamic-range = <0>; + samsung,ycbcr-coeff = <0>; + samsung,color-depth = <1>; + samsung,link-rate = <0x0a>; + samsung,lane-count = <4>; + }; diff --git a/Documentation/devicetree/bindings/video/ssd1307fb.txt b/Documentation/devicetree/bindings/video/ssd1307fb.txt new file mode 100644 index 000000000000..3d0060cff062 --- /dev/null +++ b/Documentation/devicetree/bindings/video/ssd1307fb.txt @@ -0,0 +1,24 @@ +* Solomon SSD1307 Framebuffer Driver + +Required properties: + - compatible: Should be "solomon,ssd1307fb-<bus>". The only supported bus for + now is i2c. + - reg: Should contain address of the controller on the I2C bus. Most likely + 0x3c or 0x3d + - pwm: Should contain the pwm to use according to the OF device tree PWM + specification [0] + - reset-gpios: Should contain the GPIO used to reset the OLED display + +Optional properties: + - reset-active-low: Is the reset gpio is active on physical low? + +[0]: Documentation/devicetree/bindings/pwm/pwm.txt + +Examples: +ssd1307: oled@3c { + compatible = "solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7>; + reset-active-low; +}; |
