diff options
Diffstat (limited to 'Documentation/devicetree')
6 files changed, 235 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/interrupt-controller/microchip,pic32-evic.txt b/Documentation/devicetree/bindings/interrupt-controller/microchip,pic32-evic.txt new file mode 100644 index 000000000000..c3a1b37c4c35 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/microchip,pic32-evic.txt @@ -0,0 +1,67 @@ +Microchip PIC32 Interrupt Controller +==================================== + +The Microchip PIC32 contains an Enhanced Vectored Interrupt Controller (EVIC). +It handles all internal and external interrupts. This controller exists outside +of the CPU and is the arbitrator of all interrupts (including interrupts from +the CPU itself) before they are presented to the CPU. + +External interrupts have a software configurable edge polarity. Non external +interrupts have a type and polarity that is determined by the source of the +interrupt. + +Required properties +------------------- + +- compatible: Should be "microchip,pic32mzda-evic" +- reg: Specifies physical base address and size of register range. +- interrupt-controller: Identifies the node as an interrupt controller. +- #interrupt cells: Specifies the number of cells used to encode an interrupt + source connected to this controller. The value shall be 2 and interrupt + descriptor shall have the following format: + + <hw_irq irq_type> + + hw_irq - represents the hardware interrupt number as in the data sheet. + irq_type - is used to describe the type and polarity of an interrupt. For + internal interrupts use IRQ_TYPE_EDGE_RISING for non persistent interrupts and + IRQ_TYPE_LEVEL_HIGH for persistent interrupts. For external interrupts use + IRQ_TYPE_EDGE_RISING or IRQ_TYPE_EDGE_FALLING to select the desired polarity. + +Optional properties +------------------- +- microchip,external-irqs: u32 array of external interrupts with software + polarity configuration. This array corresponds to the bits in the INTCON + SFR. + +Example +------- + +evic: interrupt-controller@1f810000 { + compatible = "microchip,pic32mzda-evic"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x1f810000 0x1000>; + microchip,external-irqs = <3 8 13 18 23>; +}; + +Each device/peripheral must request its interrupt line with the associated type +and polarity. + +Internal interrupt DTS snippet +------------------------------ + +device@1f800000 { + ... + interrupts = <113 IRQ_TYPE_LEVEL_HIGH>; + ... +}; + +External interrupt DTS snippet +------------------------------ + +device@1f800000 { + ... + interrupts = <3 IRQ_TYPE_EDGE_RISING>; + ... +}; diff --git a/Documentation/devicetree/bindings/mips/pic32/microchip,pic32mzda.txt b/Documentation/devicetree/bindings/mips/pic32/microchip,pic32mzda.txt new file mode 100644 index 000000000000..1c8dbc45feec --- /dev/null +++ b/Documentation/devicetree/bindings/mips/pic32/microchip,pic32mzda.txt @@ -0,0 +1,31 @@ +* Microchip PIC32MZDA Platforms + +PIC32MZDA Starter Kit +Required root node properties: + - compatible = "microchip,pic32mzda-sk", "microchip,pic32mzda" + +CPU nodes: +---------- +A "cpus" node is required. Required properties: + - #address-cells: Must be 1. + - #size-cells: Must be 0. +A CPU sub-node is also required. Required properties: + - device_type: Must be "cpu". + - compatible: Must be "mti,mips14KEc". +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "mti,mips14KEc"; + }; + }; + +Boot protocol +-------------- +In accordance with Unified Hosting Interface Reference Manual (MD01069), the +bootloader must pass the following arguments to the kernel: + - $a0: -2. + - $a1: KSEG0 address of the flattened device-tree blob. diff --git a/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt b/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt new file mode 100644 index 000000000000..aa6313024176 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt @@ -0,0 +1,26 @@ +Mediatek Gigabit Switch +======================= + +The mediatek gigabit switch can be found on Mediatek SoCs (mt7620, mt7621). + +Required properties: +- compatible: Should be "mediatek,mt7620-gsw" or "mediatek,mt7621-gsw" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the gigabit switches interrupt +- resets: Should contain the gigabit switches resets +- reset-names: Should contain the reset names "gsw" + +Example: + +gsw@10110000 { + compatible = "ralink,mt7620-gsw"; + reg = <0x10110000 8000>; + + resets = <&rstctrl 23>; + reset-names = "gsw"; + + interrupt-parent = <&intc>; + interrupts = <17>; +}; diff --git a/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt b/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt new file mode 100644 index 000000000000..88b095d1f13b --- /dev/null +++ b/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt @@ -0,0 +1,61 @@ +Ralink Frame Engine Ethernet controller +======================================= + +The Ralink frame engine ethernet controller can be found on Ralink and +Mediatek SoCs (RT288x, RT3x5x, RT366x, RT388x, rt5350, mt7620, mt7621, mt76x8). + +Depending on the SoC, there is a number of ports connected to the CPU port +directly and/or via a (gigabit-)switch. + +* Ethernet controller node + +Required properties: +- compatible: Should be one of "ralink,rt2880-eth", "ralink,rt3050-eth", + "ralink,rt3050-eth", "ralink,rt3883-eth", "ralink,rt5350-eth", + "mediatek,mt7620-eth", "mediatek,mt7621-eth" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the frame engines interrupt +- resets: Should contain the frame engines resets +- reset-names: Should contain the reset names "fe". If a switch is present + "esw" is also required. + + +* Ethernet port node + +Required properties: +- compatible: Should be "ralink,eth-port" +- reg: The number of the physical port +- phy-handle: reference to the node describing the phy + +Example: + +mdio-bus { + ... + phy0: ethernet-phy@0 { + phy-mode = "mii"; + reg = <0>; + }; +}; + +ethernet@400000 { + compatible = "ralink,rt2880-eth"; + reg = <0x00400000 10000>; + + #address-cells = <1>; + #size-cells = <0>; + + resets = <&rstctrl 18>; + reset-names = "fe"; + + interrupt-parent = <&cpuintc>; + interrupts = <5>; + + port@0 { + compatible = "ralink,eth-port"; + reg = <0>; + phy-handle = <&phy0>; + }; + +}; diff --git a/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt b/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt new file mode 100644 index 000000000000..2e79bd376c56 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt @@ -0,0 +1,32 @@ +Ralink Fast Ethernet Embedded Switch +==================================== + +The ralink fast ethernet embedded switch can be found on Ralink and Mediatek +SoCs (RT3x5x, RT5350, MT76x8). + +Required properties: +- compatible: Should be "ralink,rt3050-esw" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the embedded switches interrupt +- resets: Should contain the embedded switches resets +- reset-names: Should contain the reset names "esw" + +Optional properties: +- ralink,portmap: can be used to choose if the default switch setup is + llllw or wllll +- ralink,led_polarity: override the active high/low settings of the leds + +Example: + +esw@10110000 { + compatible = "ralink,rt3050-esw"; + reg = <0x10110000 8000>; + + resets = <&rstctrl 23>; + reset-names = "esw"; + + interrupt-parent = <&intc>; + interrupts = <17>; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-ath79-usb.txt b/Documentation/devicetree/bindings/phy/phy-ath79-usb.txt new file mode 100644 index 000000000000..cafe2197dad9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-ath79-usb.txt @@ -0,0 +1,18 @@ +* Atheros AR71XX/9XXX USB PHY + +Required properties: +- compatible: "qca,ar7100-usb-phy" +- #phys-cells: should be 0 +- reset-names: "usb-phy"[, "usb-suspend-override"] +- resets: references to the reset controllers + +Example: + + usb-phy { + compatible = "qca,ar7100-usb-phy"; + + reset-names = "usb-phy", "usb-suspend-override"; + resets = <&rst 4>, <&rst 3>; + + #phy-cells = <0>; + }; |
