diff options
Diffstat (limited to 'Documentation/devicetree')
112 files changed, 2793 insertions, 300 deletions
diff --git a/Documentation/devicetree/00-INDEX b/Documentation/devicetree/00-INDEX deleted file mode 100644 index 8c4102c6a5e7..000000000000 --- a/Documentation/devicetree/00-INDEX +++ /dev/null @@ -1,12 +0,0 @@ -Documentation for device trees, a data structure by which bootloaders pass -hardware layout to Linux in a device-independent manner, simplifying hardware -probing. This subsystem is maintained by Grant Likely -<grant.likely@secretlab.ca> and has a mailing list at -https://lists.ozlabs.org/listinfo/devicetree-discuss - -00-INDEX - - this file -booting-without-of.txt - - Booting Linux without Open Firmware, describes history and format of device trees. -usage-model.txt - - How Linux uses DT and what DT aims to solve.
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index 5d5bd456d9d9..e30fd106df4f 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -10,6 +10,7 @@ PHYs. Required properties: - compatible : compatible string, one of: - "allwinner,sun4i-a10-ahci" + - "allwinner,sun8i-r40-ahci" - "brcm,iproc-ahci" - "hisilicon,hisi-ahci" - "cavium,octeon-7130-ahci" @@ -31,8 +32,10 @@ Optional properties: - clocks : a list of phandle + clock specifier pairs - resets : a list of phandle + reset specifier pairs - target-supply : regulator for SATA target power +- phy-supply : regulator for PHY power - phys : reference to the SATA PHY node - phy-names : must be "sata-phy" +- ahci-supply : regulator for AHCI controller - ports-implemented : Mask that indicates which ports that the HBA supports are available for software to use. Useful if PORTS_IMPL is not programmed by the BIOS, which is true with @@ -42,12 +45,13 @@ Required properties when using sub-nodes: - #address-cells : number of cells to encode an address - #size-cells : number of cells representing the size of an address +For allwinner,sun8i-r40-ahci, the reset propertie must be present. Sub-nodes required properties: - reg : the port number And at least one of the following properties: - phys : reference to the SATA PHY node -- target-supply : regulator for SATA target power +- target-supply : regulator for SATA target power Examples: sata@ffe08000 { diff --git a/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt index 0a5b3b47f217..7713a413c6a7 100644 --- a/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt +++ b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt @@ -9,6 +9,7 @@ Required properties: "brcm,bcm7445-ahci" "brcm,bcm-nsp-ahci" "brcm,sata3-ahci" + "brcm,bcm63138-ahci" - reg : register mappings for AHCI and SATA_TOP_CTRL - reg-names : "ahci" and "top-ctrl" - interrupts : interrupt mapping for SATA IRQ diff --git a/Documentation/devicetree/bindings/connector/usb-connector.txt b/Documentation/devicetree/bindings/connector/usb-connector.txt index 8855bfcfd778..d90e17e2428b 100644 --- a/Documentation/devicetree/bindings/connector/usb-connector.txt +++ b/Documentation/devicetree/bindings/connector/usb-connector.txt @@ -29,15 +29,15 @@ Required properties for usb-c-connector with power delivery support: in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.2 Source_Capabilities Message, the order of each entry(PDO) should follow the PD spec chapter 6.4.1. Required for power source and power dual role. - User can specify the source PDO array via PDO_FIXED/BATT/VAR() defined in - dt-bindings/usb/pd.h. + User can specify the source PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() + defined in dt-bindings/usb/pd.h. - sink-pdos: An array of u32 with each entry providing supported power sink data object(PDO), the detailed bit definitions of PDO can be found in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.3 Sink Capabilities Message, the order of each entry(PDO) should follow the PD spec chapter 6.4.1. Required for power sink and power dual role. - User can specify the sink PDO array via PDO_FIXED/BATT/VAR() defined in - dt-bindings/usb/pd.h. + User can specify the sink PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() defined + in dt-bindings/usb/pd.h. - op-sink-microwatt: Sink required operating power in microwatt, if source can't offer the power, Capability Mismatch is set. Required for power sink and power dual role. diff --git a/Documentation/devicetree/bindings/dma/jz4780-dma.txt b/Documentation/devicetree/bindings/dma/jz4780-dma.txt index 03e9cf7b42e0..636fcb26b164 100644 --- a/Documentation/devicetree/bindings/dma/jz4780-dma.txt +++ b/Documentation/devicetree/bindings/dma/jz4780-dma.txt @@ -2,8 +2,13 @@ Required properties: -- compatible: Should be "ingenic,jz4780-dma" -- reg: Should contain the DMA controller registers location and length. +- compatible: Should be one of: + * ingenic,jz4740-dma + * ingenic,jz4725b-dma + * ingenic,jz4770-dma + * ingenic,jz4780-dma +- reg: Should contain the DMA channel registers location and length, followed + by the DMA controller registers location and length. - interrupts: Should contain the interrupt specifier of the DMA controller. - clocks: Should contain a clock specifier for the JZ4780 PDMA clock. - #dma-cells: Must be <2>. Number of integer cells in the dmas property of @@ -19,9 +24,10 @@ Optional properties: Example: -dma: dma@13420000 { +dma: dma-controller@13420000 { compatible = "ingenic,jz4780-dma"; - reg = <0x13420000 0x10000>; + reg = <0x13420000 0x400 + 0x13421000 0x40>; interrupt-parent = <&intc>; interrupts = <10>; diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt index 946229c48657..a5a7c3f5a1e3 100644 --- a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt @@ -17,6 +17,7 @@ Required Properties: - compatible: "renesas,dmac-<soctype>", "renesas,rcar-dmac" as fallback. Examples with soctypes are: - "renesas,dmac-r8a7743" (RZ/G1M) + - "renesas,dmac-r8a7744" (RZ/G1N) - "renesas,dmac-r8a7745" (RZ/G1E) - "renesas,dmac-r8a77470" (RZ/G1C) - "renesas,dmac-r8a7790" (R-Car H2) diff --git a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt index 482e54362d3e..1743017bd948 100644 --- a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt @@ -4,6 +4,7 @@ Required Properties: -compatible: "renesas,<soctype>-usb-dmac", "renesas,usb-dmac" as fallback. Examples with soctypes are: - "renesas,r8a7743-usb-dmac" (RZ/G1M) + - "renesas,r8a7744-usb-dmac" (RZ/G1N) - "renesas,r8a7745-usb-dmac" (RZ/G1E) - "renesas,r8a7790-usb-dmac" (R-Car H2) - "renesas,r8a7791-usb-dmac" (R-Car M2-W) diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index a7c31de29362..f0ba154b5723 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -1,18 +1,9 @@ Specifying GPIO information for devices -============================================ +======================================= 1) gpios property ----------------- -Nodes that makes use of GPIOs should specify them using one or more -properties, each containing a 'gpio-list': - - gpio-list ::= <single-gpio> [gpio-list] - single-gpio ::= <gpio-phandle> <gpio-specifier> - gpio-phandle : phandle to gpio controller node - gpio-specifier : Array of #gpio-cells specifying specific gpio - (controller specific) - GPIO properties should be named "[<name>-]gpios", with <name> being the purpose of this GPIO for the device. While a non-existent <name> is considered valid for compatibility reasons (resolving to the "gpios" property), it is not allowed @@ -33,33 +24,27 @@ The following example could be used to describe GPIO pins used as device enable and bit-banged data signals: gpio1: gpio1 { - gpio-controller - #gpio-cells = <2>; - }; - gpio2: gpio2 { - gpio-controller - #gpio-cells = <1>; + gpio-controller; + #gpio-cells = <2>; }; [...] - enable-gpios = <&gpio2 2>; data-gpios = <&gpio1 12 0>, <&gpio1 13 0>, <&gpio1 14 0>, <&gpio1 15 0>; -Note that gpio-specifier length is controller dependent. In the -above example, &gpio1 uses 2 cells to specify a gpio, while &gpio2 -only uses one. +In the above example, &gpio1 uses 2 cells to specify a gpio. The first cell is +a local offset to the GPIO line and the second cell represent consumer flags, +such as if the consumer desire the line to be active low (inverted) or open +drain. This is the recommended practice. -gpio-specifier may encode: bank, pin position inside the bank, -whether pin is open-drain and whether pin is logically inverted. +The exact meaning of each specifier cell is controller specific, and must be +documented in the device tree binding for the device, but it is strongly +recommended to use the two-cell approach. -Exact meaning of each specifier cell is controller specific, and must -be documented in the device tree binding for the device. - -Most controllers are however specifying a generic flag bitfield -in the last cell, so for these, use the macros defined in +Most controllers are specifying a generic flag bitfield in the last cell, so +for these, use the macros defined in include/dt-bindings/gpio/gpio.h whenever possible: Example of a node using GPIOs: @@ -236,46 +221,40 @@ Example of two SOC GPIO banks defined as gpio-controller nodes: Some or all of the GPIOs provided by a GPIO controller may be routed to pins on the package via a pin controller. This allows muxing those pins between -GPIO and other functions. +GPIO and other functions. It is a fairly common practice among silicon +engineers. + +2.2) Ordinary (numerical) GPIO ranges +------------------------------------- It is useful to represent which GPIOs correspond to which pins on which pin -controllers. The gpio-ranges property described below represents this, and -contains information structures as follows: - - gpio-range-list ::= <single-gpio-range> [gpio-range-list] - single-gpio-range ::= <numeric-gpio-range> | <named-gpio-range> - numeric-gpio-range ::= - <pinctrl-phandle> <gpio-base> <pinctrl-base> <count> - named-gpio-range ::= <pinctrl-phandle> <gpio-base> '<0 0>' - pinctrl-phandle : phandle to pin controller node - gpio-base : Base GPIO ID in the GPIO controller - pinctrl-base : Base pinctrl pin ID in the pin controller - count : The number of GPIOs/pins in this range - -The "pin controller node" mentioned above must conform to the bindings -described in ../pinctrl/pinctrl-bindings.txt. - -In case named gpio ranges are used (ranges with both <pinctrl-base> and -<count> set to 0), the property gpio-ranges-group-names contains one string -for every single-gpio-range in gpio-ranges: - gpiorange-names-list ::= <gpiorange-name> [gpiorange-names-list] - gpiorange-name : Name of the pingroup associated to the GPIO range in - the respective pin controller. - -Elements of gpiorange-names-list corresponding to numeric ranges contain -the empty string. Elements of gpiorange-names-list corresponding to named -ranges contain the name of a pin group defined in the respective pin -controller. The number of pins/GPIOs in the range is the number of pins in -that pin group. +controllers. The gpio-ranges property described below represents this with +a discrete set of ranges mapping pins from the pin controller local number space +to pins in the GPIO controller local number space. -Previous versions of this binding required all pin controller nodes that -were referenced by any gpio-ranges property to contain a property named -#gpio-range-cells with value <3>. This requirement is now deprecated. -However, that property may still exist in older device trees for -compatibility reasons, and would still be required even in new device -trees that need to be compatible with older software. +The format is: <[pin controller phandle], [GPIO controller offset], + [pin controller offset], [number of pins]>; + +The GPIO controller offset pertains to the GPIO controller node containing the +range definition. + +The pin controller node referenced by the phandle must conform to the bindings +described in pinctrl/pinctrl-bindings.txt. + +Each offset runs from 0 to N. It is perfectly fine to pile any number of +ranges with just one pin-to-GPIO line mapping if the ranges are concocted, but +in practice these ranges are often lumped in discrete sets. + +Example: + + gpio-ranges = <&foo 0 20 10>, <&bar 10 50 20>; -Example 1: +This means: +- pins 20..29 on pin controller "foo" is mapped to GPIO line 0..9 and +- pins 50..69 on pin controller "bar" is mapped to GPIO line 10..29 + + +Verbose example: qe_pio_e: gpio-controller@1460 { #gpio-cells = <2>; @@ -289,7 +268,28 @@ Here, a single GPIO controller has GPIOs 0..9 routed to pin controller pinctrl1's pins 20..29, and GPIOs 10..29 routed to pin controller pinctrl2's pins 50..69. -Example 2: + +2.3) GPIO ranges from named pin groups +-------------------------------------- + +It is also possible to use pin groups for gpio ranges when pin groups are the +easiest and most convenient mapping. + +Both both <pinctrl-base> and <count> must set to 0 when using named pin groups +names. + +The property gpio-ranges-group-names must contain exactly one string for each +range. + +Elements of gpio-ranges-group-names must contain the name of a pin group +defined in the respective pin controller. The number of pins/GPIO lines in the +range is the number of pins in that pin group. The number of pins of that +group is defined int the implementation and not in the device tree. + +If numerical and named pin groups are mixed, the string corresponding to a +numerical pin range in gpio-ranges-group-names must be empty. + +Example: gpio_pio_i: gpio-controller@14b0 { #gpio-cells = <2>; @@ -306,6 +306,14 @@ Example 2: "bar"; }; -Here, three GPIO ranges are defined wrt. two pin controllers. pinctrl1 GPIO -ranges are defined using pin numbers whereas the GPIO ranges wrt. pinctrl2 -are named "foo" and "bar". +Here, three GPIO ranges are defined referring to two pin controllers. + +pinctrl1 GPIO ranges are defined using pin numbers whereas the GPIO ranges +in pinctrl2 are defined using the pin groups named "foo" and "bar". + +Previous versions of this binding required all pin controller nodes that +were referenced by any gpio-ranges property to contain a property named +#gpio-range-cells with value <3>. This requirement is now deprecated. +However, that property may still exist in older device trees for +compatibility reasons, and would still be required even in new device +trees that need to be compatible with older software. diff --git a/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt b/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt deleted file mode 100644 index 7988aeb725f4..000000000000 --- a/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt +++ /dev/null @@ -1,46 +0,0 @@ -Ingenic jz47xx GPIO controller - -That the Ingenic GPIO driver node must be a sub-node of the Ingenic pinctrl -driver node. - -Required properties: --------------------- - - - compatible: Must contain one of: - - "ingenic,jz4740-gpio" - - "ingenic,jz4770-gpio" - - "ingenic,jz4780-gpio" - - reg: The GPIO bank number. - - interrupt-controller: Marks the device node as an interrupt controller. - - interrupts: Interrupt specifier for the controllers interrupt. - - #interrupt-cells: Should be 2. Refer to - ../interrupt-controller/interrupts.txt for more details. - - gpio-controller: Marks the device node as a GPIO controller. - - #gpio-cells: Should be 2. The first cell is the GPIO number and the second - cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the - GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. - - gpio-ranges: Range of pins managed by the GPIO controller. Refer to - 'gpio.txt' in this directory for more details. - -Example: --------- - -&pinctrl { - #address-cells = <1>; - #size-cells = <0>; - - gpa: gpio@0 { - compatible = "ingenic,jz4740-gpio"; - reg = <0>; - - gpio-controller; - gpio-ranges = <&pinctrl 0 0 32>; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - - interrupt-parent = <&intc>; - interrupts = <28>; - }; -}; diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index 4018ee57a6af..2889bbcd7416 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -4,8 +4,10 @@ Required Properties: - compatible: should contain one or more of the following: - "renesas,gpio-r8a7743": for R8A7743 (RZ/G1M) compatible GPIO controller. + - "renesas,gpio-r8a7744": for R8A7744 (RZ/G1N) compatible GPIO controller. - "renesas,gpio-r8a7745": for R8A7745 (RZ/G1E) compatible GPIO controller. - "renesas,gpio-r8a77470": for R8A77470 (RZ/G1C) compatible GPIO controller. + - "renesas,gpio-r8a774a1": for R8A774A1 (RZ/G2M) compatible GPIO controller. - "renesas,gpio-r8a7778": for R8A7778 (R-Car M1) compatible GPIO controller. - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller. - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller. @@ -22,7 +24,7 @@ Required Properties: - "renesas,gpio-r8a77995": for R8A77995 (R-Car D3) compatible GPIO controller. - "renesas,rcar-gen1-gpio": for a generic R-Car Gen1 GPIO controller. - "renesas,rcar-gen2-gpio": for a generic R-Car Gen2 or RZ/G1 GPIO controller. - - "renesas,rcar-gen3-gpio": for a generic R-Car Gen3 GPIO controller. + - "renesas,rcar-gen3-gpio": for a generic R-Car Gen3 or RZ/G2 GPIO controller. - "renesas,gpio-rcar": deprecated. When compatible with the generic version nodes must list the @@ -38,7 +40,7 @@ Required Properties: - #gpio-cells: Should be 2. The first cell is the GPIO number and the second cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. - - gpio-ranges: Range of pins managed by the GPIO controller. + - gpio-ranges: See gpio.txt. Optional properties: @@ -46,35 +48,44 @@ Optional properties: mandatory if the hardware implements a controllable functional clock for the GPIO instance. -Please refer to gpio.txt in this directory for details of gpio-ranges property -and the common GPIO bindings used by client devices. + - gpio-reserved-ranges: See gpio.txt. + +Please refer to gpio.txt in this directory for the common GPIO bindings used by +client devices. The GPIO controller also acts as an interrupt controller. It uses the default two cells specifier as described in Documentation/devicetree/bindings/ interrupt-controller/interrupts.txt. -Example: R8A7779 (R-Car H1) GPIO controller nodes +Example: R8A77470 (RZ/G1C) GPIO controller nodes - gpio0: gpio@ffc40000 { - compatible = "renesas,gpio-r8a7779", "renesas,rcar-gen1-gpio"; - reg = <0xffc40000 0x2c>; - interrupt-parent = <&gic>; - interrupts = <0 141 0x4>; - #gpio-cells = <2>; - gpio-controller; - gpio-ranges = <&pfc 0 0 32>; - interrupt-controller; - #interrupt-cells = <2>; - }; + gpio0: gpio@e6050000 { + compatible = "renesas,gpio-r8a77470", + "renesas,rcar-gen2-gpio"; + reg = <0 0xe6050000 0 0x50>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 0 23>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&cpg CPG_MOD 912>; + power-domains = <&sysc R8A77470_PD_ALWAYS_ON>; + resets = <&cpg 912>; + }; ... - gpio6: gpio@ffc46000 { - compatible = "renesas,gpio-r8a7779", "renesas,rcar-gen1-gpio"; - reg = <0xffc46000 0x2c>; - interrupt-parent = <&gic>; - interrupts = <0 147 0x4>; - #gpio-cells = <2>; - gpio-controller; - gpio-ranges = <&pfc 0 192 9>; - interrupt-controller; - #interrupt-cells = <2>; - }; + gpio3: gpio@e6053000 { + compatible = "renesas,gpio-r8a77470", + "renesas,rcar-gen2-gpio"; + reg = <0 0xe6053000 0 0x50>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 96 30>; + gpio-reserved-ranges = <17 10>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&cpg CPG_MOD 909>; + power-domains = <&sysc R8A77470_PD_ALWAYS_ON>; + resets = <&cpg 909>; + }; diff --git a/Documentation/devicetree/bindings/gpio/snps,creg-gpio.txt b/Documentation/devicetree/bindings/gpio/snps,creg-gpio.txt new file mode 100644 index 000000000000..1b30812b015b --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/snps,creg-gpio.txt @@ -0,0 +1,21 @@ +Synopsys GPIO via CREG (Control REGisters) driver + +Required properties: +- compatible : "snps,creg-gpio-hsdk" or "snps,creg-gpio-axs10x". +- reg : Exactly one register range with length 0x4. +- #gpio-cells : Since the generic GPIO binding is used, the + amount of cells must be specified as 2. The first cell is the + pin number, the second cell is used to specify optional parameters: + See "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt. +- gpio-controller : Marks the device node as a GPIO controller. +- ngpios: Number of GPIO pins. + +Example: + +gpio: gpio@f00014b0 { + compatible = "snps,creg-gpio-hsdk"; + reg = <0xf00014b0 0x4>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <2>; +}; diff --git a/Documentation/devicetree/bindings/hwmon/ina3221.txt b/Documentation/devicetree/bindings/hwmon/ina3221.txt new file mode 100644 index 000000000000..a7b25caa2b8e --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ina3221.txt @@ -0,0 +1,44 @@ +Texas Instruments INA3221 Device Tree Bindings + +1) ina3221 node + Required properties: + - compatible: Must be "ti,ina3221" + - reg: I2C address + + Optional properties: + = The node contains optional child nodes for three channels = + = Each child node describes the information of input source = + + - #address-cells: Required only if a child node is present. Must be 1. + - #size-cells: Required only if a child node is present. Must be 0. + +2) child nodes + Required properties: + - reg: Must be 0, 1 or 2, corresponding to IN1, IN2 or IN3 port of INA3221 + + Optional properties: + - label: Name of the input source + - shunt-resistor-micro-ohms: Shunt resistor value in micro-Ohm + +Example: + +ina3221@40 { + compatible = "ti,ina3221"; + reg = <0x40>; + #address-cells = <1>; + #size-cells = <0>; + + input@0 { + reg = <0x0>; + status = "disabled"; + }; + input@1 { + reg = <0x1>; + shunt-resistor-micro-ohms = <5000>; + }; + input@2 { + reg = <0x2>; + label = "VDD_5V"; + shunt-resistor-micro-ohms = <5000>; + }; +}; diff --git a/Documentation/devicetree/bindings/hwmon/ltc2978.txt b/Documentation/devicetree/bindings/hwmon/ltc2978.txt index bf2a47bbdc58..b428a70a7cc0 100644 --- a/Documentation/devicetree/bindings/hwmon/ltc2978.txt +++ b/Documentation/devicetree/bindings/hwmon/ltc2978.txt @@ -15,6 +15,7 @@ Required properties: * "lltc,ltm2987" * "lltc,ltm4675" * "lltc,ltm4676" + * "lltc,ltm4686" - reg: I2C slave address Optional properties: @@ -30,6 +31,7 @@ Valid names of regulators depend on number of supplies supported per device: * ltc3880, ltc3882, ltc3886 : vout0 - vout1 * ltc3883 : vout0 * ltm4676 : vout0 - vout1 + * ltm4686 : vout0 - vout1 Example: ltc2978@5e { diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt index aa8bf2ec8905..1c94a57a661e 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt @@ -5,6 +5,8 @@ The Marvell ICU (Interrupt Consolidation Unit) controller is responsible for collecting all wired-interrupt sources in the CP and communicating them to the GIC in the AP, the unit translates interrupt requests on input wires to MSG memory mapped transactions to the GIC. +These messages will access a different GIC memory area depending on +their type (NSR, SR, SEI, REI, etc). Required properties: @@ -12,20 +14,23 @@ Required properties: - reg: Should contain ICU registers location and length. -- #interrupt-cells: Specifies the number of cells needed to encode an - interrupt source. The value shall be 3. +Subnodes: Each group of interrupt is declared as a subnode of the ICU, +with their own compatible. + +Required properties for the icu_nsr/icu_sei subnodes: - The 1st cell is the group type of the ICU interrupt. Possible group - types are: +- compatible: Should be one of: + * "marvell,cp110-icu-nsr" + * "marvell,cp110-icu-sr" + * "marvell,cp110-icu-sei" + * "marvell,cp110-icu-rei" - ICU_GRP_NSR (0x0) : Shared peripheral interrupt, non-secure - ICU_GRP_SR (0x1) : Shared peripheral interrupt, secure - ICU_GRP_SEI (0x4) : System error interrupt - ICU_GRP_REI (0x5) : RAM error interrupt +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. The value shall be 2. - The 2nd cell is the index of the interrupt in the ICU unit. + The 1st cell is the index of the interrupt in the ICU unit. - The 3rd cell is the type of the interrupt. See arm,gic.txt for + The 2nd cell is the type of the interrupt. See arm,gic.txt for details. - interrupt-controller: Identifies the node as an interrupt @@ -35,17 +40,73 @@ Required properties: that allows to trigger interrupts using MSG memory mapped transactions. +Note: each 'interrupts' property referring to any 'icu_xxx' node shall + have a different number within [0:206]. + Example: icu: interrupt-controller@1e0000 { compatible = "marvell,cp110-icu"; - reg = <0x1e0000 0x10>; + reg = <0x1e0000 0x440>; + + CP110_LABEL(icu_nsr): interrupt-controller@10 { + compatible = "marvell,cp110-icu-nsr"; + reg = <0x10 0x20>; + #interrupt-cells = <2>; + interrupt-controller; + msi-parent = <&gicp>; + }; + + CP110_LABEL(icu_sei): interrupt-controller@50 { + compatible = "marvell,cp110-icu-sei"; + reg = <0x50 0x10>; + #interrupt-cells = <2>; + interrupt-controller; + msi-parent = <&sei>; + }; +}; + +node1 { + interrupt-parent = <&icu_nsr>; + interrupts = <106 IRQ_TYPE_LEVEL_HIGH>; +}; + +node2 { + interrupt-parent = <&icu_sei>; + interrupts = <107 IRQ_TYPE_LEVEL_HIGH>; +}; + +/* Would not work with the above nodes */ +node3 { + interrupt-parent = <&icu_nsr>; + interrupts = <107 IRQ_TYPE_LEVEL_HIGH>; +}; + +The legacy bindings were different in this way: + +- #interrupt-cells: The value was 3. + The 1st cell was the group type of the ICU interrupt. Possible + group types were: + ICU_GRP_NSR (0x0) : Shared peripheral interrupt, non-secure + ICU_GRP_SR (0x1) : Shared peripheral interrupt, secure + ICU_GRP_SEI (0x4) : System error interrupt + ICU_GRP_REI (0x5) : RAM error interrupt + The 2nd cell was the index of the interrupt in the ICU unit. + The 3rd cell was the type of the interrupt. See arm,gic.txt for + details. + +Example: + +icu: interrupt-controller@1e0000 { + compatible = "marvell,cp110-icu"; + reg = <0x1e0000 0x440>; + #interrupt-cells = <3>; interrupt-controller; msi-parent = <&gicp>; }; -usb3h0: usb3@500000 { +node1 { interrupt-parent = <&icu>; interrupts = <ICU_GRP_NSR 106 IRQ_TYPE_LEVEL_HIGH>; }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,sei.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,sei.txt new file mode 100644 index 000000000000..0beafed502f5 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,sei.txt @@ -0,0 +1,36 @@ +Marvell SEI (System Error Interrupt) Controller +----------------------------------------------- + +Marvell SEI (System Error Interrupt) controller is an interrupt +aggregator. It receives interrupts from several sources and aggregates +them to a single interrupt line (an SPI) on the parent interrupt +controller. + +This interrupt controller can handle up to 64 SEIs, a set comes from the +AP and is wired while a second set comes from the CPs by the mean of +MSIs. + +Required properties: + +- compatible: should be one of: + * "marvell,ap806-sei" +- reg: SEI registers location and length. +- interrupts: identifies the parent IRQ that will be triggered. +- #interrupt-cells: number of cells to define an SEI wired interrupt + coming from the AP, should be 1. The cell is the IRQ + number. +- interrupt-controller: identifies the node as an interrupt controller + for AP interrupts. +- msi-controller: identifies the node as an MSI controller for the CPs + interrupts. + +Example: + + sei: interrupt-controller@3f0200 { + compatible = "marvell,ap806-sei"; + reg = <0x3f0200 0x40>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; + #interrupt-cells = <1>; + interrupt-controller; + msi-controller; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt index a046ed374d80..8de96a4fb2d5 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt @@ -2,10 +2,12 @@ DT bindings for the R-Mobile/R-Car/RZ/G interrupt controller Required properties: -- compatible: has to be "renesas,irqc-<soctype>", "renesas,irqc" as fallback. +- compatible: must be "renesas,irqc-<soctype>" or "renesas,intc-ex-<soctype>", + and "renesas,irqc" as fallback. Examples with soctypes are: - "renesas,irqc-r8a73a4" (R-Mobile APE6) - "renesas,irqc-r8a7743" (RZ/G1M) + - "renesas,irqc-r8a7744" (RZ/G1N) - "renesas,irqc-r8a7745" (RZ/G1E) - "renesas,irqc-r8a77470" (RZ/G1C) - "renesas,irqc-r8a7790" (R-Car H2) @@ -19,6 +21,7 @@ Required properties: - "renesas,intc-ex-r8a77965" (R-Car M3-N) - "renesas,intc-ex-r8a77970" (R-Car V3M) - "renesas,intc-ex-r8a77980" (R-Car V3H) + - "renesas,intc-ex-r8a77990" (R-Car E3) - "renesas,intc-ex-r8a77995" (R-Car D3) - #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in interrupts.txt in this directory diff --git a/Documentation/devicetree/bindings/leds/leds-an30259a.txt b/Documentation/devicetree/bindings/leds/leds-an30259a.txt new file mode 100644 index 000000000000..6ffb861083c0 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-an30259a.txt @@ -0,0 +1,43 @@ +* Panasonic AN30259A 3-channel LED driver + +The AN30259A is a LED controller capable of driving three LEDs independently. It supports +constant current output and sloping current output modes. The chip is connected over I2C. + +Required properties: + - compatible: Must be "panasonic,an30259a". + - reg: I2C slave address. + - #address-cells: Must be 1. + - #size-cells: Must be 0. + +Each LED is represented as a sub-node of the panasonic,an30259a node. + +Required sub-node properties: + - reg: Pin that the LED is connected to. Must be 1, 2, or 3. + +Optional sub-node properties: + - label: see Documentation/devicetree/bindings/leds/common.txt + - linux,default-trigger: see Documentation/devicetree/bindings/leds/common.txt + +Example: +led-controller@30 { + compatible = "panasonic,an30259a"; + reg = <0x30>; + #address-cells = <1>; + #size-cells = <0>; + + led@1 { + reg = <1>; + linux,default-trigger = "heartbeat"; + label = "red:indicator"; + }; + + led@2 { + reg = <2>; + label = "green:indicator"; + }; + + led@3 { + reg = <3>; + label = "blue:indicator"; + }; +}; diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/mfd/atmel-usart.txt index 7c0d6b2f53e4..7f0cd72f47d2 100644 --- a/Documentation/devicetree/bindings/serial/atmel-usart.txt +++ b/Documentation/devicetree/bindings/mfd/atmel-usart.txt @@ -1,6 +1,6 @@ * Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART) -Required properties: +Required properties for USART: - compatible: Should be "atmel,<chip>-usart" or "atmel,<chip>-dbgu" The compatible <chip> indicated will be the first SoC to support an additional mode or an USART new feature. @@ -11,7 +11,13 @@ Required properties: Required elements: "usart" - clocks: phandles to input clocks. -Optional properties: +Required properties for USART in SPI mode: +- #size-cells : Must be <0> +- #address-cells : Must be <1> +- cs-gpios: chipselects (internal cs not supported) +- atmel,usart-mode : Must be <AT91_USART_MODE_SPI> (found in dt-bindings/mfd/at91-usart.h) + +Optional properties in serial mode: - atmel,use-dma-rx: use of PDC or DMA for receiving data - atmel,use-dma-tx: use of PDC or DMA for transmitting data - {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively. @@ -62,3 +68,18 @@ Example: dma-names = "tx", "rx"; atmel,fifo-size = <32>; }; + +- SPI mode: + #include <dt-bindings/mfd/at91-usart.h> + + spi0: spi@f001c000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-usart", "atmel,at91sam9260-usart"; + atmel,usart-mode = <AT91_USART_MODE_SPI>; + reg = <0xf001c000 0x100>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>; + clocks = <&usart0_clk>; + clock-names = "usart"; + cs-gpios = <&pioB 3 0>; + }; diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt index 3ca56fdb5ffe..a4b056761eaa 100644 --- a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt @@ -1,16 +1,17 @@ -* ROHM BD71837 Power Management Integrated Circuit bindings +* ROHM BD71837 and BD71847 Power Management Integrated Circuit bindings -BD71837MWV is a programmable Power Management IC for powering single-core, -dual-core, and quad-core SoCs such as NXP-i.MX 8M. It is optimized for -low BOM cost and compact solution footprint. It integrates 8 Buck -egulators and 7 LDOs to provide all the power rails required by the SoC and -the commonly used peripherals. +BD71837MWV and BD71847MWV are programmable Power Management ICs for powering +single-core, dual-core, and quad-core SoCs such as NXP-i.MX 8M. They are +optimized for low BOM cost and compact solution footprint. BD71837MWV +integrates 8 Buck regulators and 7 LDOs. BD71847MWV contains 6 Buck regulators +and 6 LDOs. -Datasheet for PMIC is available at: +Datasheet for BD71837 is available at: https://www.rohm.com/datasheet/BD71837MWV/bd71837mwv-e Required properties: - - compatible : Should be "rohm,bd71837". + - compatible : Should be "rohm,bd71837" for bd71837 + "rohm,bd71847" for bd71847. - reg : I2C slave address. - interrupt-parent : Phandle to the parent interrupt controller. - interrupts : The interrupt line the device is connected to. diff --git a/Documentation/devicetree/bindings/mips/mscc.txt b/Documentation/devicetree/bindings/mips/mscc.txt index ae15ec333542..bc817e984628 100644 --- a/Documentation/devicetree/bindings/mips/mscc.txt +++ b/Documentation/devicetree/bindings/mips/mscc.txt @@ -41,3 +41,19 @@ Example: compatible = "mscc,ocelot-cpu-syscon", "syscon"; reg = <0x70000000 0x2c>; }; + +o HSIO regs: + +The SoC has a few registers (HSIO) handling miscellaneous functionalities: +configuration and status of PLL5, RCOMP, SyncE, SerDes configurations and +status, SerDes muxing and a thermal sensor. + +Required properties: +- compatible: Should be "mscc,ocelot-hsio", "syscon", "simple-mfd" +- reg : Should contain registers location and length + +Example: + syscon@10d0000 { + compatible = "mscc,ocelot-hsio", "syscon", "simple-mfd"; + reg = <0x10d0000 0x10000>; + }; diff --git a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt index f6ddba31cb73..e2effe17f05e 100644 --- a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt @@ -15,6 +15,7 @@ Required Properties: - "arasan,sdhci-5.1": generic Arasan SDHCI 5.1 PHY - "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1": rk3399 eMMC PHY For this device it is strongly suggested to include arasan,soc-ctl-syscon. + - "ti,am654-sdhci-5.1", "arasan,sdhci-5.1": TI AM654 MMC PHY - reg: From mmc bindings: Register location and length. - clocks: From clock bindings: Handles to clock inputs. - clock-names: From clock bindings: Tuple including "clk_xin" and "clk_ahb" diff --git a/Documentation/devicetree/bindings/mmc/jz4740.txt b/Documentation/devicetree/bindings/mmc/jz4740.txt index 7cd8c432d7c8..8a6f87f13114 100644 --- a/Documentation/devicetree/bindings/mmc/jz4740.txt +++ b/Documentation/devicetree/bindings/mmc/jz4740.txt @@ -7,6 +7,7 @@ described in mmc.txt. Required properties: - compatible: Should be one of the following: - "ingenic,jz4740-mmc" for the JZ4740 + - "ingenic,jz4725b-mmc" for the JZ4725B - "ingenic,jz4780-mmc" for the JZ4780 - reg: Should contain the MMC controller registers location and length. - interrupts: Should contain the interrupt specifier of the MMC controller. diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt index 03796cf2d3e7..6d3c626e017d 100644 --- a/Documentation/devicetree/bindings/mmc/mmci.txt +++ b/Documentation/devicetree/bindings/mmc/mmci.txt @@ -15,8 +15,11 @@ Required properties: Optional properties: - arm,primecell-periphid : contains the PrimeCell Peripheral ID, it overrides the ID provided by the HW +- resets : phandle to internal reset line. + Should be defined for sdmmc variant. - vqmmc-supply : phandle to the regulator device tree node, mentioned as the VCCQ/VDD_IO supply in the eMMC/SD specs. +specific for ux500 variant: - st,sig-dir-dat0 : bus signal direction pin used for DAT[0]. - st,sig-dir-dat2 : bus signal direction pin used for DAT[2]. - st,sig-dir-dat31 : bus signal direction pin used for DAT[3] and DAT[1]. @@ -24,6 +27,14 @@ Optional properties: - st,sig-dir-cmd : cmd signal direction pin used for CMD. - st,sig-pin-fbclk : feedback clock signal pin used. +specific for sdmmc variant: +- st,sig-dir : signal direction polarity used for cmd, dat0 dat123. +- st,neg-edge : data & command phase relation, generated on + sd clock falling edge. +- st,use-ckin : use ckin pin from an external driver to sample + the receive data (example: with voltage + switch transceiver). + Deprecated properties: - mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable. - mmc-cap-sd-highspeed : indicates whether SD is high speed capable. diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt index f33467a54a05..f5bcda3980cc 100644 --- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt @@ -10,6 +10,7 @@ Required properties: - compatible: value should be either of the following. "mediatek,mt8135-mmc": for mmc host ip compatible with mt8135 "mediatek,mt8173-mmc": for mmc host ip compatible with mt8173 + "mediatek,mt8183-mmc": for mmc host ip compatible with mt8183 "mediatek,mt2701-mmc": for mmc host ip compatible with mt2701 "mediatek,mt2712-mmc": for mmc host ip compatible with mt2712 "mediatek,mt7622-mmc": for MT7622 SoC @@ -22,6 +23,7 @@ Required properties: "source" - source clock (required) "hclk" - HCLK which used for host (required) "source_cg" - independent source clock gate (required for MT2712) + "bus_clk" - bus clock used for internal register access (required for MT2712 MSDC0/3) - pinctrl-names: should be "default", "state_uhs" - pinctrl-0: should contain default/high speed pin ctrl - pinctrl-1: should contain uhs mode pin ctrl diff --git a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt index 9bce57862ed6..32b4b4e41923 100644 --- a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt @@ -38,3 +38,75 @@ sdhci@c8000200 { power-gpios = <&gpio 155 0>; /* gpio PT3 */ bus-width = <8>; }; + +Optional properties for Tegra210 and Tegra186: +- pinctrl-names, pinctrl-0, pinctrl-1 : Specify pad voltage + configurations. Valid pinctrl-names are "sdmmc-3v3" and "sdmmc-1v8" + for controllers supporting multiple voltage levels. The order of names + should correspond to the pin configuration states in pinctrl-0 and + pinctrl-1. +- nvidia,only-1-8-v : The presence of this property indicates that the + controller operates at a 1.8 V fixed I/O voltage. +- nvidia,pad-autocal-pull-up-offset-3v3, + nvidia,pad-autocal-pull-down-offset-3v3 : Specify drive strength + calibration offsets for 3.3 V signaling modes. +- nvidia,pad-autocal-pull-up-offset-1v8, + nvidia,pad-autocal-pull-down-offset-1v8 : Specify drive strength + calibration offsets for 1.8 V signaling modes. +- nvidia,pad-autocal-pull-up-offset-3v3-timeout, + nvidia,pad-autocal-pull-down-offset-3v3-timeout : Specify drive + strength used as a fallback in case the automatic calibration times + out on a 3.3 V signaling mode. +- nvidia,pad-autocal-pull-up-offset-1v8-timeout, + nvidia,pad-autocal-pull-down-offset-1v8-timeout : Specify drive + strength used as a fallback in case the automatic calibration times + out on a 1.8 V signaling mode. +- nvidia,pad-autocal-pull-up-offset-sdr104, + nvidia,pad-autocal-pull-down-offset-sdr104 : Specify drive strength + calibration offsets for SDR104 mode. +- nvidia,pad-autocal-pull-up-offset-hs400, + nvidia,pad-autocal-pull-down-offset-hs400 : Specify drive strength + calibration offsets for HS400 mode. +- nvidia,default-tap : Specify the default inbound sampling clock + trimmer value for non-tunable modes. +- nvidia,default-trim : Specify the default outbound clock trimmer + value. +- nvidia,dqs-trim : Specify DQS trim value for HS400 timing + + Notes on the pad calibration pull up and pulldown offset values: + - The property values are drive codes which are programmed into the + PD_OFFSET and PU_OFFSET sections of the + SDHCI_TEGRA_AUTO_CAL_CONFIG register. + - A higher value corresponds to higher drive strength. Please refer + to the reference manual of the SoC for correct values. + - The SDR104 and HS400 timing specific values are used in + corresponding modes if specified. + + Notes on tap and trim values: + - The values are used for compensating trace length differences + by adjusting the sampling point. + - The values are programmed to the Vendor Clock Control Register. + Please refer to the reference manual of the SoC for correct + values. + - The DQS trim values are only used on controllers which support + HS400 timing. Only SDMMC4 on Tegra210 and Tegra 186 supports + HS400. + +Example: +sdhci@700b0000 { + compatible = "nvidia,tegra210-sdhci", "nvidia,tegra124-sdhci"; + reg = <0x0 0x700b0000 0x0 0x200>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA210_CLK_SDMMC1>; + clock-names = "sdhci"; + resets = <&tegra_car 14>; + reset-names = "sdhci"; + pinctrl-names = "sdmmc-3v3", "sdmmc-1v8"; + pinctrl-0 = <&sdmmc1_3v3>; + pinctrl-1 = <&sdmmc1_1v8>; + nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>; + nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>; + nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>; + nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt index 5ff1e12c655a..c064af5838aa 100644 --- a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt @@ -12,6 +12,7 @@ Required properties: - "renesas,mmcif-r8a73a4" for the MMCIF found in r8a73a4 SoCs - "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs - "renesas,mmcif-r8a7743" for the MMCIF found in r8a7743 SoCs + - "renesas,mmcif-r8a7744" for the MMCIF found in r8a7744 SoCs - "renesas,mmcif-r8a7745" for the MMCIF found in r8a7745 SoCs - "renesas,mmcif-r8a7778" for the MMCIF found in r8a7778 SoCs - "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs @@ -23,7 +24,8 @@ Required properties: - interrupts: Some SoCs have only 1 shared interrupt, while others have either 2 or 3 individual interrupts (error, int, card detect). Below is the number of interrupts for each SoC: - 1: r8a73a4, r8a7743, r8a7745, r8a7778, r8a7790, r8a7791, r8a7793, r8a7794 + 1: r8a73a4, r8a7743, r8a7744, r8a7745, r8a7778, r8a7790, r8a7791, r8a7793, + r8a7794 2: r8a7740, sh73a0 3: r7s72100 diff --git a/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt b/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt new file mode 100644 index 000000000000..45c9978aad7b --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt @@ -0,0 +1,41 @@ +* Spreadtrum SDHCI controller (sdhci-sprd) + +The Secure Digital (SD) Host controller on Spreadtrum SoCs provides an interface +for MMC, SD and SDIO types of cards. + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-sprd driver. + +Required properties: +- compatible: Should contain "sprd,sdhci-r11". +- reg: physical base address of the controller and length. +- interrupts: Interrupts used by the SDHCI controller. +- clocks: Should contain phandle for the clock feeding the SDHCI controller +- clock-names: Should contain the following: + "sdio" - SDIO source clock (required) + "enable" - gate clock which used for enabling/disabling the device (required) + +Optional properties: +- assigned-clocks: the same with "sdio" clock +- assigned-clock-parents: the default parent of "sdio" clock + +Examples: + +sdio0: sdio@20600000 { + compatible = "sprd,sdhci-r11"; + reg = <0 0x20600000 0 0x1000>; + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; + + clock-names = "sdio", "enable"; + clocks = <&ap_clk CLK_EMMC_2X>, + <&apahb_gate CLK_EMMC_EB>; + assigned-clocks = <&ap_clk CLK_EMMC_2X>; + assigned-clock-parents = <&rpll CLK_RPLL_390M>; + + bus-width = <8>; + non-removable; + no-sdio; + no-sd; + cap-mmc-hw-reset; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index c434200d19d5..27f2eab2981d 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -16,7 +16,11 @@ Required properties: "renesas,sdhi-r8a73a4" - SDHI IP on R8A73A4 SoC "renesas,sdhi-r8a7740" - SDHI IP on R8A7740 SoC "renesas,sdhi-r8a7743" - SDHI IP on R8A7743 SoC + "renesas,sdhi-r8a7744" - SDHI IP on R8A7744 SoC "renesas,sdhi-r8a7745" - SDHI IP on R8A7745 SoC + "renesas,sdhi-r8a774a1" - SDHI IP on R8A774A1 SoC + "renesas,sdhi-r8a77470" - SDHI IP on R8A77470 SoC + "renesas,sdhi-mmc-r8a77470" - SDHI/MMC IP on R8A77470 SoC "renesas,sdhi-r8a7778" - SDHI IP on R8A7778 SoC "renesas,sdhi-r8a7779" - SDHI IP on R8A7779 SoC "renesas,sdhi-r8a7790" - SDHI IP on R8A7790 SoC @@ -27,14 +31,16 @@ Required properties: "renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC "renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC "renesas,sdhi-r8a77965" - SDHI IP on R8A77965 SoC + "renesas,sdhi-r8a77970" - SDHI IP on R8A77970 SoC "renesas,sdhi-r8a77980" - SDHI IP on R8A77980 SoC "renesas,sdhi-r8a77990" - SDHI IP on R8A77990 SoC "renesas,sdhi-r8a77995" - SDHI IP on R8A77995 SoC "renesas,sdhi-shmobile" - a generic sh-mobile SDHI controller "renesas,rcar-gen1-sdhi" - a generic R-Car Gen1 SDHI controller - "renesas,rcar-gen2-sdhi" - a generic R-Car Gen2 or RZ/G1 + "renesas,rcar-gen2-sdhi" - a generic R-Car Gen2 and RZ/G1 SDHI + (not SDHI/MMC) controller + "renesas,rcar-gen3-sdhi" - a generic R-Car Gen3 or RZ/G2 SDHI controller - "renesas,rcar-gen3-sdhi" - a generic R-Car Gen3 SDHI controller When compatible with the generic version, nodes must list diff --git a/Documentation/devicetree/bindings/mmc/uniphier-sd.txt b/Documentation/devicetree/bindings/mmc/uniphier-sd.txt new file mode 100644 index 000000000000..e1d658755722 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/uniphier-sd.txt @@ -0,0 +1,55 @@ +UniPhier SD/eMMC controller + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-sd-v2.91" - IP version 2.91 + "socionext,uniphier-sd-v3.1" - IP version 3.1 + "socionext,uniphier-sd-v3.1.1" - IP version 3.1.1 +- reg: offset and length of the register set for the device. +- interrupts: a single interrupt specifier. +- clocks: a single clock specifier of the controller clock. +- reset-names: should contain the following: + "host" - mandatory for all versions + "bridge" - should exist only for "socionext,uniphier-sd-v2.91" + "hw" - should exist if eMMC hw reset line is available +- resets: a list of reset specifiers, corresponding to the reset-names + +Optional properties: +- pinctrl-names: if present, should contain the following: + "default" - should exist for all instances + "uhs" - should exist for SD instance with UHS support +- pinctrl-0: pin control state for the default mode +- pinctrl-1: pin control state for the UHS mode +- dma-names: should be "rx-tx" if present. + This property can exist only for "socionext,uniphier-sd-v2.91". +- dmas: a single DMA channel specifier + This property can exist only for "socionext,uniphier-sd-v2.91". +- bus-width: see mmc.txt +- cap-sd-highspeed: see mmc.txt +- cap-mmc-highspeed: see mmc.txt +- sd-uhs-sdr12: see mmc.txt +- sd-uhs-sdr25: see mmc.txt +- sd-uhs-sdr50: see mmc.txt +- cap-mmc-hw-reset: should exist if reset-names contains "hw". see mmc.txt +- non-removable: see mmc.txt + +Example: + + sd: sdhc@5a400000 { + compatible = "socionext,uniphier-sd-v2.91"; + reg = <0x5a400000 0x200>; + interrupts = <0 76 4>; + pinctrl-names = "default", "uhs"; + pinctrl-0 = <&pinctrl_sd>; + pinctrl-1 = <&pinctrl_sd_uhs>; + clocks = <&mio_clk 0>; + reset-names = "host", "bridge"; + resets = <&mio_rst 0>, <&mio_rst 3>; + dma-names = "rx-tx"; + dmas = <&dmac 4>; + bus-width = <4>; + cap-sd-highspeed; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + }; diff --git a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt index 4648948f7c3b..e15589f47787 100644 --- a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt +++ b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt @@ -19,6 +19,9 @@ Optional properties: - interrupt-names: must be "mdio_done_error" when there is a share interrupt fed to this hardware block, or must be "mdio_done" for the first interrupt and "mdio_error" for the second when there are separate interrupts +- clocks: A reference to the clock supplying the MDIO bus controller +- clock-frequency: the MDIO bus clock that must be output by the MDIO bus + hardware, if absent, the default hardware values are used Child nodes of this MDIO bus controller node are standard Ethernet PHY device nodes as described in Documentation/devicetree/bindings/net/phy.txt diff --git a/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt new file mode 100644 index 000000000000..886cbe8ffb38 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt @@ -0,0 +1,143 @@ +Lantiq GSWIP Ethernet switches +================================== + +Required properties for GSWIP core: + +- compatible : "lantiq,xrx200-gswip" for the embedded GSWIP in the + xRX200 SoC +- reg : memory range of the GSWIP core registers + : memory range of the GSWIP MDIO registers + : memory range of the GSWIP MII registers + +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of +additional required and optional properties. + + +Required properties for MDIO bus: +- compatible : "lantiq,xrx200-mdio" for the MDIO bus inside the GSWIP + core of the xRX200 SoC and the PHYs connected to it. + +See Documentation/devicetree/bindings/net/mdio.txt for a list of additional +required and optional properties. + + +Required properties for GPHY firmware loading: +- compatible : "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw" + "lantiq,xrx300-gphy-fw", "lantiq,gphy-fw" + "lantiq,xrx330-gphy-fw", "lantiq,gphy-fw" + for the loading of the firmware into the embedded + GPHY core of the SoC. +- lantiq,rcu : reference to the rcu syscon + +The GPHY firmware loader has a list of GPHY entries, one for each +embedded GPHY + +- reg : Offset of the GPHY firmware register in the RCU + register range +- resets : list of resets of the embedded GPHY +- reset-names : list of names of the resets + +Example: + +Ethernet switch on the VRX200 SoC: + +switch@e108000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-gswip"; + reg = < 0xe108000 0x3100 /* switch */ + 0xe10b100 0xd8 /* mdio */ + 0xe10b1d8 0x130 /* mii */ + >; + dsa,member = <0 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan3"; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + }; + + port@1 { + reg = <1>; + label = "lan4"; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-mode = "internal"; + phy-handle = <&phy11>; + }; + + port@4 { + reg = <4>; + label = "lan1"; + phy-mode = "internal"; + phy-handle = <&phy13>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + + port@6 { + reg = <0x6>; + label = "cpu"; + ethernet = <ð0>; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x0>; + }; + phy1: ethernet-phy@1 { + reg = <0x1>; + }; + phy5: ethernet-phy@5 { + reg = <0x5>; + }; + phy11: ethernet-phy@11 { + reg = <0x11>; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + }; + }; + + gphy-fw { + compatible = "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw"; + lantiq,rcu = <&rcu0>; + #address-cells = <1>; + #size-cells = <0>; + + gphy@20 { + reg = <0x20>; + + resets = <&reset0 31 30>; + reset-names = "gphy"; + }; + + gphy@68 { + reg = <0x68>; + + resets = <&reset0 29 28>; + reset-names = "gphy"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/lantiq,xrx200-net.txt b/Documentation/devicetree/bindings/net/lantiq,xrx200-net.txt new file mode 100644 index 000000000000..5ff5e68bbbb6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/lantiq,xrx200-net.txt @@ -0,0 +1,21 @@ +Lantiq xRX200 GSWIP PMAC Ethernet driver +================================== + +Required properties: + +- compatible : "lantiq,xrx200-net" for the PMAC of the embedded + : GSWIP in the xXR200 +- reg : memory range of the PMAC core inside of the GSWIP core +- interrupts : TX and RX DMA interrupts. Use interrupt-names "tx" for + : the TX interrupt and "rx" for the RX interrupt. + +Example: + +ethernet@e10b308 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-net"; + reg = <0xe10b308 0xcf8>; + interrupts = <73>, <72>; + interrupt-names = "tx", "rx"; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt index fc019df0d863..b78397669320 100644 --- a/Documentation/devicetree/bindings/net/marvell-pp2.txt +++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt @@ -31,7 +31,7 @@ required. Required properties (port): -- interrupts: interrupt for the port +- interrupts: interrupt(s) for the port - port-id: ID of the port from the MAC point of view - gop-port-id: only for marvell,armada-7k-pp2, ID of the port from the GOP (Group Of Ports) point of view. This ID is used to index the @@ -43,10 +43,12 @@ Optional properties (port): - marvell,loopback: port is loopback mode - phy: a phandle to a phy node defining the PHY address (as the reg property, a single integer). -- interrupt-names: if more than a single interrupt for rx is given, must - be the name associated to the interrupts listed. Valid - names are: "tx-cpu0", "tx-cpu1", "tx-cpu2", "tx-cpu3", - "rx-shared", "link". +- interrupt-names: if more than a single interrupt for is given, must be the + name associated to the interrupts listed. Valid names are: + "hifX", with X in [0..8], and "link". The names "tx-cpu0", + "tx-cpu1", "tx-cpu2", "tx-cpu3" and "rx-shared" are supported + for backward compatibility but shouldn't be used for new + additions. - marvell,system-controller: a phandle to the system controller. Example for marvell,armada-375-pp2: @@ -89,9 +91,14 @@ cpm_ethernet: ethernet@0 { <ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared"; + <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 59 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 63 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 67 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 71 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 129 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; port-id = <0>; gop-port-id = <0>; }; @@ -101,9 +108,14 @@ cpm_ethernet: ethernet@0 { <ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared"; + <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 60 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 64 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 68 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 72 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 128 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; port-id = <1>; gop-port-id = <2>; }; @@ -113,9 +125,14 @@ cpm_ethernet: ethernet@0 { <ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared"; + <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 61 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 65 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 69 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 73 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 127 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; port-id = <2>; gop-port-id = <3>; }; diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt index e22d8cfea687..5100358177c9 100644 --- a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -1,4 +1,4 @@ -Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY +Micrel KSZ9021/KSZ9031/KSZ9131 Gigabit Ethernet PHY Some boards require special tuning values, particularly when it comes to clock delays. You can specify clock delay values in the PHY OF @@ -64,6 +64,32 @@ KSZ9031: Attention: The link partner must be configurable as slave otherwise no link will be established. +KSZ9131: + + All skew control options are specified in picoseconds. The increment + step is 100ps. Unlike KSZ9031, the values represent picoseccond delays. + A negative value can be assigned as rxc-skew-psec = <(-100)>;. + + Optional properties: + + Range of the value -700 to 2400, default value 0: + + - rxc-skew-psec : Skew control of RX clock pad + - txc-skew-psec : Skew control of TX clock pad + + Range of the value -700 to 800, default value 0: + + - rxdv-skew-psec : Skew control of RX CTL pad + - txen-skew-psec : Skew control of TX CTL pad + - rxd0-skew-psec : Skew control of RX data 0 pad + - rxd1-skew-psec : Skew control of RX data 1 pad + - rxd2-skew-psec : Skew control of RX data 2 pad + - rxd3-skew-psec : Skew control of RX data 3 pad + - txd0-skew-psec : Skew control of TX data 0 pad + - txd1-skew-psec : Skew control of TX data 1 pad + - txd2-skew-psec : Skew control of TX data 2 pad + - txd3-skew-psec : Skew control of TX data 3 pad + Examples: mdio { diff --git a/Documentation/devicetree/bindings/net/mscc-ocelot.txt b/Documentation/devicetree/bindings/net/mscc-ocelot.txt index 0a84711abece..9e5c17d426ce 100644 --- a/Documentation/devicetree/bindings/net/mscc-ocelot.txt +++ b/Documentation/devicetree/bindings/net/mscc-ocelot.txt @@ -12,7 +12,6 @@ Required properties: - "sys" - "rew" - "qs" - - "hsio" - "qsys" - "ana" - "portX" with X from 0 to the number of last port index available on that @@ -45,7 +44,6 @@ Example: reg = <0x1010000 0x10000>, <0x1030000 0x10000>, <0x1080000 0x100>, - <0x10d0000 0x10000>, <0x11e0000 0x100>, <0x11f0000 0x100>, <0x1200000 0x100>, @@ -59,10 +57,9 @@ Example: <0x1280000 0x100>, <0x1800000 0x80000>, <0x1880000 0x10000>; - reg-names = "sys", "rew", "qs", "hsio", "port0", - "port1", "port2", "port3", "port4", "port5", - "port6", "port7", "port8", "port9", "port10", - "qsys", "ana"; + reg-names = "sys", "rew", "qs", "port0", "port1", "port2", + "port3", "port4", "port5", "port6", "port7", + "port8", "port9", "port10", "qsys", "ana"; interrupts = <21 22>; interrupt-names = "xtr", "inj"; diff --git a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt index 0eedabe22cc3..5ff37c68c941 100644 --- a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt +++ b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt @@ -1,10 +1,5 @@ * Microsemi - vsc8531 Giga bit ethernet phy -Required properties: -- compatible : Should contain phy id as "ethernet-phy-idAAAA.BBBB" - The PHY device uses the binding described in - Documentation/devicetree/bindings/net/phy.txt - Optional properties: - vsc8531,vddmac : The vddmac in mV. Allowed values is listed in the first row of Table 1 (below). @@ -27,14 +22,16 @@ Optional properties: 'vddmac'. Default value is 0%. Ref: Table:1 - Edge rate change (below). -- vsc8531,led-0-mode : LED mode. Specify how the LED[0] should behave. - Allowed values are define in - "include/dt-bindings/net/mscc-phy-vsc8531.h". - Default value is VSC8531_LINK_1000_ACTIVITY (1). -- vsc8531,led-1-mode : LED mode. Specify how the LED[1] should behave. - Allowed values are define in +- vsc8531,led-[N]-mode : LED mode. Specify how the LED[N] should behave. + N depends on the number of LEDs supported by a + PHY. + Allowed values are defined in "include/dt-bindings/net/mscc-phy-vsc8531.h". - Default value is VSC8531_LINK_100_ACTIVITY (2). + Default values are VSC8531_LINK_1000_ACTIVITY (1), + VSC8531_LINK_100_ACTIVITY (2), + VSC8531_LINK_ACTIVITY (0) and + VSC8531_DUPLEX_COLLISION (8). + Table: 1 - Edge rate change ----------------------------------------------------------------| diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index da249b7c406c..3530256a879c 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -6,6 +6,7 @@ interface contains. Required properties: - compatible: Must contain one or more of the following: - "renesas,etheravb-r8a7743" for the R8A7743 SoC. + - "renesas,etheravb-r8a7744" for the R8A7744 SoC. - "renesas,etheravb-r8a7745" for the R8A7745 SoC. - "renesas,etheravb-r8a77470" for the R8A77470 SoC. - "renesas,etheravb-r8a7790" for the R8A7790 SoC. diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index 7fd4e8ce4149..2196d1ab3c8c 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -56,6 +56,11 @@ Optional properties: the length can vary between hw versions. - <supply-name>-supply: handle to the regulator device tree node optional "supply-name" is "vdd-0.8-cx-mx". +- memory-region: + Usage: optional + Value type: <phandle> + Definition: reference to the reserved-memory for the msa region + used by the wifi firmware running in Q6. Example (to supply the calibration data alone): @@ -149,4 +154,5 @@ wifi@18000000 { <0 140 0 /* CE10 */ >, <0 141 0 /* CE11 */ >; vdd-0.8-cx-mx-supply = <&pm8998_l5>; + memory-region = <&wifi_msa_mem>; }; diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index cb33421184a0..f37494d5a7be 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -50,6 +50,7 @@ Additional required properties for imx7d-pcie: - reset-names: Must contain the following entires: - "pciephy" - "apps" + - "turnoff" Example: diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt index 4dd17de549a7..2030ee0dc4f9 100644 --- a/Documentation/devicetree/bindings/pci/pci-keystone.txt +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -19,6 +19,9 @@ pcie_msi_intc : Interrupt controller device node for MSI IRQ chip interrupt-cells: should be set to 1 interrupts: GIC interrupt lines connected to PCI MSI interrupt lines +ti,syscon-pcie-id : phandle to the device control module required to set device + id and vendor id. + Example: pcie_msi_intc: msi-interrupt-controller { interrupt-controller; diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt index 9fe7e12a7bf3..b94078f58d8e 100644 --- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -7,6 +7,7 @@ OHCI and EHCI controllers. Required properties: - compatible: "renesas,pci-r8a7743" for the R8A7743 SoC; + "renesas,pci-r8a7744" for the R8A7744 SoC; "renesas,pci-r8a7745" for the R8A7745 SoC; "renesas,pci-r8a7790" for the R8A7790 SoC; "renesas,pci-r8a7791" for the R8A7791 SoC; diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index a5f7fc62d10e..976ef7bfff93 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -2,6 +2,7 @@ Required properties: compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; + "renesas,pcie-r8a7744" for the R8A7744 SoC; "renesas,pcie-r8a7779" for the R8A7779 SoC; "renesas,pcie-r8a7790" for the R8A7790 SoC; "renesas,pcie-r8a7791" for the R8A7791 SoC; @@ -9,6 +10,7 @@ compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; "renesas,pcie-r8a7795" for the R8A7795 SoC; "renesas,pcie-r8a7796" for the R8A7796 SoC; "renesas,pcie-r8a77980" for the R8A77980 SoC; + "renesas,pcie-r8a77990" for the R8A77990 SoC; "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 or RZ/G1 compatible device. "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 compatible device. diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt index 7f7af3044016..452fe48c4fdd 100644 --- a/Documentation/devicetree/bindings/pci/ti-pci.txt +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt @@ -26,6 +26,11 @@ HOST MODE ranges, interrupt-map-mask, interrupt-map : as specified in ../designware-pcie.txt + - ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument + should contain the register offset within syscon + and the 2nd argument should contain the bit field + for setting the bit to enable unaligned + access. DEVICE MODE =========== diff --git a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt index 0aced97d8092..b640845fec67 100644 --- a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt +++ b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt @@ -8,6 +8,7 @@ Required properties: "brcm,iproc-nsp-sata-phy" "brcm,phy-sata3" "brcm,iproc-sr-sata-phy" + "brcm,bcm63138-sata-phy" - address-cells: should be 1 - size-cells: should be 0 - reg: register ranges for the PHY PCB interface diff --git a/Documentation/devicetree/bindings/phy/phy-cadence-dp.txt b/Documentation/devicetree/bindings/phy/phy-cadence-dp.txt new file mode 100644 index 000000000000..7f49fd54ebc1 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-cadence-dp.txt @@ -0,0 +1,30 @@ +Cadence MHDP DisplayPort SD0801 PHY binding +=========================================== + +This binding describes the Cadence SD0801 PHY hardware included with +the Cadence MHDP DisplayPort controller. + +------------------------------------------------------------------------------- +Required properties (controller (parent) node): +- compatible : Should be "cdns,dp-phy" +- reg : Defines the following sets of registers in the parent + mhdp device: + - Offset of the DPTX PHY configuration registers + - Offset of the SD0801 PHY configuration registers +- #phy-cells : from the generic PHY bindings, must be 0. + +Optional properties: +- num_lanes : Number of DisplayPort lanes to use (1, 2 or 4) +- max_bit_rate : Maximum DisplayPort link bit rate to use, in Mbps (2160, + 2430, 2700, 3240, 4320, 5400 or 8100) +------------------------------------------------------------------------------- + +Example: + dp_phy: phy@f0fb030a00 { + compatible = "cdns,dp-phy"; + reg = <0xf0 0xfb030a00 0x0 0x00000040>, + <0xf0 0xfb500000 0x0 0x00100000>; + num_lanes = <4>; + max_bit_rate = <8100>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-ocelot-serdes.txt b/Documentation/devicetree/bindings/phy/phy-ocelot-serdes.txt new file mode 100644 index 000000000000..332219860187 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-ocelot-serdes.txt @@ -0,0 +1,43 @@ +Microsemi Ocelot SerDes muxing driver +------------------------------------- + +On Microsemi Ocelot, there is a handful of registers in HSIO address +space for setting up the SerDes to switch port muxing. + +A SerDes X can be "muxed" to work with switch port Y or Z for example. +One specific SerDes can also be used as a PCIe interface. + +Hence, a SerDes represents an interface, be it an Ethernet or a PCIe one. + +There are two kinds of SerDes: SERDES1G supports 10/100Mbps in +half/full-duplex and 1000Mbps in full-duplex mode while SERDES6G supports +10/100Mbps in half/full-duplex and 1000/2500Mbps in full-duplex mode. + +Also, SERDES6G number (aka "macro") 0 is the only interface supporting +QSGMII. + +This is a child of the HSIO syscon ("mscc,ocelot-hsio", see +Documentation/devicetree/bindings/mips/mscc.txt) on the Microsemi Ocelot. + +Required properties: + +- compatible: should be "mscc,vsc7514-serdes" +- #phy-cells : from the generic phy bindings, must be 2. + The first number defines the input port to use for a given + SerDes macro. The second defines the macro to use. They are + defined in dt-bindings/phy/phy-ocelot-serdes.h + +Example: + + serdes: serdes { + compatible = "mscc,vsc7514-serdes"; + #phy-cells = <2>; + }; + + ethernet { + port1 { + phy-handle = <&phy_foo>; + /* Link SERDES1G_5 to port1 */ + phys = <&serdes 1 SERDES1G_5>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-hdmi.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-hdmi.txt new file mode 100644 index 000000000000..710cccd5ee56 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-hdmi.txt @@ -0,0 +1,43 @@ +ROCKCHIP HDMI PHY WITH INNO IP BLOCK + +Required properties: + - compatible : should be one of the listed compatibles: + * "rockchip,rk3228-hdmi-phy", + * "rockchip,rk3328-hdmi-phy"; + - reg : Address and length of the hdmi phy control register set + - clocks : phandle + clock specifier for the phy clocks + - clock-names : string, clock name, must contain "sysclk" for system + control and register configuration, "refoclk" for crystal- + oscillator reference PLL clock input and "refpclk" for pclk- + based refeference PLL clock input. + - #clock-cells: should be 0. + - clock-output-names : shall be the name for the output clock. + - interrupts : phandle + interrupt specified for the hdmiphy interrupt + - #phy-cells : must be 0. See ./phy-bindings.txt for details. + +Optional properties for rk3328-hdmi-phy: + - nvmem-cells = phandle + nvmem specifier for the cpu-version efuse + - nvmem-cell-names : "cpu-version" to read the chip version, required + for adjustment to some frequency settings + +Example: + hdmi_phy: hdmi-phy@12030000 { + compatible = "rockchip,rk3228-hdmi-phy"; + reg = <0x12030000 0x10000>; + #phy-cells = <0>; + clocks = <&cru PCLK_HDMI_PHY>, <&xin24m>, <&cru DCLK_HDMIPHY>; + clock-names = "sysclk", "refoclk", "refpclk"; + #clock-cells = <0>; + clock-output-names = "hdmi_phy"; + status = "disabled"; + }; + +Then the PHY can be used in other nodes such as: + + hdmi: hdmi@200a0000 { + compatible = "rockchip,rk3228-dw-hdmi"; + ... + phys = <&hdmi_phy>; + phy-names = "hdmi"; + ... + }; diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt index 0c7629e88bf3..adf20b2bdf71 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt @@ -10,16 +10,20 @@ Required properties: "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996, "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996, "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845, - "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845. + "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845, + "qcom,sdm845-qmp-ufs-phy" for UFS QMP phy on sdm845. - - reg: - - For "qcom,sdm845-qmp-usb3-phy": - - index 0: address and length of register set for PHY's common serdes - block. - - named register "dp_com" (using reg-names): address and length of the - DP_COM control block. - - For all others: - - offset and length of register set for PHY's common serdes block. +- reg: + - index 0: address and length of register set for PHY's common + serdes block. + - index 1: address and length of the DP_COM control block (for + "qcom,sdm845-qmp-usb3-phy" only). + +- reg-names: + - For "qcom,sdm845-qmp-usb3-phy": + - Should be: "reg-base", "dp_com" + - For all others: + - The reg-names property shouldn't be defined. - #clock-cells: must be 1 - Phy pll outputs a bunch of clocks for Tx, Rx and Pipe @@ -35,6 +39,7 @@ Required properties: "aux" for phy aux clock, "ref" for 19.2 MHz ref clk, "com_aux" for phy common block aux clock, + "ref_aux" for phy reference aux clock, For "qcom,msm8996-qmp-pcie-phy" must contain: "aux", "cfg_ahb", "ref". For "qcom,msm8996-qmp-usb3-phy" must contain: diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt index fb4a204da2bf..de7b5393c163 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt @@ -1,10 +1,12 @@ * Renesas R-Car generation 3 USB 2.0 PHY This file provides information on what the device node for the R-Car generation -3 USB 2.0 PHY contains. +3 and RZ/G2 USB 2.0 PHY contain. Required properties: -- compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 +- compatible: "renesas,usb2-phy-r8a774a1" if the device is a part of an R8A774A1 + SoC. + "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 SoC. "renesas,usb2-phy-r8a7796" if the device is a part of an R8A7796 SoC. @@ -14,7 +16,8 @@ Required properties: R8A77990 SoC. "renesas,usb2-phy-r8a77995" if the device is a part of an R8A77995 SoC. - "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 compatible device. + "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 or RZ/G2 + compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first @@ -31,6 +34,8 @@ channel as USB OTG: - interrupts: interrupt specifier for the PHY. - vbus-supply: Phandle to a regulator that provides power to the VBUS. This regulator will be managed during the PHY power on/off sequence. +- renesas,no-otg-pins: boolean, specify when a board does not provide proper + otg pins. Example (R-Car H3): diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt index 47dd296ecead..9d9826609c2f 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt @@ -1,20 +1,22 @@ * Renesas R-Car generation 3 USB 3.0 PHY This file provides information on what the device node for the R-Car generation -3 USB 3.0 PHY contains. +3 and RZ/G2 USB 3.0 PHY contain. If you want to enable spread spectrum clock (ssc), you should use USB_EXTAL instead of USB3_CLK. However, if you don't want to these features, you don't need this driver. Required properties: -- compatible: "renesas,r8a7795-usb3-phy" if the device is a part of an R8A7795 +- compatible: "renesas,r8a774a1-usb3-phy" if the device is a part of an R8A774A1 + SoC. + "renesas,r8a7795-usb3-phy" if the device is a part of an R8A7795 SoC. "renesas,r8a7796-usb3-phy" if the device is a part of an R8A7796 SoC. "renesas,r8a77965-usb3-phy" if the device is a part of an R8A77965 SoC. - "renesas,rcar-gen3-usb3-phy" for a generic R-Car Gen3 compatible - device. + "renesas,rcar-gen3-usb3-phy" for a generic R-Car Gen3 or RZ/G2 + compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first diff --git a/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt b/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt new file mode 100644 index 000000000000..1889d3b89d68 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt @@ -0,0 +1,31 @@ +Socionext UniPhier PCIe PHY bindings + +This describes the devicetree bindings for PHY interface built into +PCIe controller implemented on Socionext UniPhier SoCs. + +Required properties: +- compatible: Should contain one of the following: + "socionext,uniphier-ld20-pcie-phy" - for LD20 PHY + "socionext,uniphier-pxs3-pcie-phy" - for PXs3 PHY +- reg: Specifies offset and length of the register set for the device. +- #phy-cells: Must be zero. +- clocks: A phandle to the clock gate for PCIe glue layer including + this phy. +- resets: A phandle to the reset line for PCIe glue layer including + this phy. + +Optional properties: +- socionext,syscon: A phandle to system control to set configurations + for phy. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + pcie_phy: phy@66038000 { + compatible = "socionext,uniphier-ld20-pcie-phy"; + reg = <0x66038000 0x4000>; + #phy-cells = <0>; + clocks = <&sys_clk 24>; + resets = <&sys_rst 24>; + socionext,syscon = <&soc_glue>; + }; diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb2-phy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb2-phy.txt new file mode 100644 index 000000000000..b43b28250cc0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/uniphier-usb2-phy.txt @@ -0,0 +1,45 @@ +Socionext UniPhier USB2 PHY + +This describes the devicetree bindings for PHY interface built into +USB2 controller implemented on Socionext UniPhier SoCs. + +Pro4 SoC has both USB2 and USB3 host controllers, however, this USB3 +controller doesn't include its own High-Speed PHY. This needs to specify +USB2 PHY instead of USB3 HS-PHY. + +Required properties: +- compatible: Should contain one of the following: + "socionext,uniphier-pro4-usb2-phy" - for Pro4 SoC + "socionext,uniphier-ld11-usb2-phy" - for LD11 SoC + +Sub-nodes: +Each PHY should be represented as a sub-node. + +Sub-nodes required properties: +- #phy-cells: Should be 0. +- reg: The number of the PHY. + +Sub-nodes optional properties: +- vbus-supply: A phandle to the regulator for USB VBUS. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + soc-glue@5f800000 { + ... + usb-phy { + compatible = "socionext,uniphier-ld11-usb2-phy"; + usb_phy0: phy@0 { + reg = <0>; + #phy-cells = <0>; + }; + ... + }; + }; + + usb@5a800100 { + compatible = "socionext,uniphier-ehci", "generic-ehci"; + ... + phy-names = "usb"; + phys = <&usb_phy0>; + }; diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt new file mode 100644 index 000000000000..e8d8086a7ae9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt @@ -0,0 +1,69 @@ +Socionext UniPhier USB3 High-Speed (HS) PHY + +This describes the devicetree bindings for PHY interfaces built into +USB3 controller implemented on Socionext UniPhier SoCs. +Although the controller includes High-Speed PHY and Super-Speed PHY, +this describes about High-Speed PHY. + +Required properties: +- compatible: Should contain one of the following: + "socionext,uniphier-pro4-usb3-hsphy" - for Pro4 SoC + "socionext,uniphier-pxs2-usb3-hsphy" - for PXs2 SoC + "socionext,uniphier-ld20-usb3-hsphy" - for LD20 SoC + "socionext,uniphier-pxs3-usb3-hsphy" - for PXs3 SoC +- reg: Specifies offset and length of the register set for the device. +- #phy-cells: Should be 0. +- clocks: A list of phandles to the clock gate for USB3 glue layer. + According to the clock-names, appropriate clocks are required. +- clock-names: Should contain the following: + "gio", "link" - for Pro4 SoC + "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional. + "phy", "link" - for others +- resets: A list of phandles to the reset control for USB3 glue layer. + According to the reset-names, appropriate resets are required. +- reset-names: Should contain the following: + "gio", "link" - for Pro4 SoC + "phy", "link" - for others + +Optional properties: +- vbus-supply: A phandle to the regulator for USB VBUS. +- nvmem-cells: Phandles to nvmem cell that contains the trimming data. + Available only for HS-PHY implemented on LD20 and PXs3, and + if unspecified, default value is used. +- nvmem-cell-names: Should be the following names, which correspond to + each nvmem-cells. + All of the 3 parameters associated with the following names are + required for each port, if any one is omitted, the trimming data + of the port will not be set at all. + "rterm", "sel_t", "hs_i" - Each cell name for phy parameters + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + + usb-glue@65b00000 { + compatible = "socionext,uniphier-ld20-dwc3-glue", + "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x65b00000 0x400>; + + usb_vbus0: regulator { + ... + }; + + usb_hsphy0: hs-phy@200 { + compatible = "socionext,uniphier-ld20-usb3-hsphy"; + reg = <0x200 0x10>; + #phy-cells = <0>; + clock-names = "link", "phy"; + clocks = <&sys_clk 14>, <&sys_clk 16>; + reset-names = "link", "phy"; + resets = <&sys_rst 14>, <&sys_rst 16>; + vbus-supply = <&usb_vbus0>; + nvmem-cell-names = "rterm", "sel_t", "hs_i"; + nvmem-cells = <&usb_rterm0>, <&usb_sel_t0>, + <&usb_hs_i0>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt new file mode 100644 index 000000000000..490b815445e8 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt @@ -0,0 +1,57 @@ +Socionext UniPhier USB3 Super-Speed (SS) PHY + +This describes the devicetree bindings for PHY interfaces built into +USB3 controller implemented on Socionext UniPhier SoCs. +Although the controller includes High-Speed PHY and Super-Speed PHY, +this describes about Super-Speed PHY. + +Required properties: +- compatible: Should contain one of the following: + "socionext,uniphier-pro4-usb3-ssphy" - for Pro4 SoC + "socionext,uniphier-pxs2-usb3-ssphy" - for PXs2 SoC + "socionext,uniphier-ld20-usb3-ssphy" - for LD20 SoC + "socionext,uniphier-pxs3-usb3-ssphy" - for PXs3 SoC +- reg: Specifies offset and length of the register set for the device. +- #phy-cells: Should be 0. +- clocks: A list of phandles to the clock gate for USB3 glue layer. + According to the clock-names, appropriate clocks are required. +- clock-names: + "gio", "link" - for Pro4 SoC + "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional. + "phy", "link" - for others +- resets: A list of phandles to the reset control for USB3 glue layer. + According to the reset-names, appropriate resets are required. +- reset-names: + "gio", "link" - for Pro4 SoC + "phy", "link" - for others + +Optional properties: +- vbus-supply: A phandle to the regulator for USB VBUS. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + + usb-glue@65b00000 { + compatible = "socionext,uniphier-ld20-dwc3-glue", + "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x65b00000 0x400>; + + usb_vbus0: regulator { + ... + }; + + usb_ssphy0: ss-phy@300 { + compatible = "socionext,uniphier-ld20-usb3-ssphy"; + reg = <0x300 0x10>; + #phy-cells = <0>; + clock-names = "link", "phy"; + clocks = <&sys_clk 14>, <&sys_clk 16>; + reset-names = "link", "phy"; + resets = <&sys_rst 14>, <&sys_rst 16>; + vbus-supply = <&usb_vbus0>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm4708-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm4708-pinmux.txt new file mode 100644 index 000000000000..4fa9539070cb --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm4708-pinmux.txt @@ -0,0 +1,57 @@ +Broadcom Northstar pins mux controller + +Some of Northstar SoCs's pins can be used for various purposes thanks to the mux +controller. This binding allows describing mux controller and listing available +functions. They can be referenced later by other bindings to let system +configure controller correctly. + +A list of pins varies across chipsets so few bindings are available. + +Required properties: +- compatible: must be one of: + "brcm,bcm4708-pinmux" + "brcm,bcm4709-pinmux" + "brcm,bcm53012-pinmux" +- reg: iomem address range of CRU (Central Resource Unit) pin registers +- reg-names: "cru_gpio_control" - the only needed & supported reg right now + +Functions and their groups available for all chipsets: +- "spi": "spi_grp" +- "i2c": "i2c_grp" +- "pwm": "pwm0_grp", "pwm1_grp", "pwm2_grp", "pwm3_grp" +- "uart1": "uart1_grp" + +Additionally available on BCM4709 and BCM53012: +- "mdio": "mdio_grp" +- "uart2": "uart2_grp" +- "sdio": "sdio_pwr_grp", "sdio_1p8v_grp" + +For documentation of subnodes see: +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Example: + dmu@1800c000 { + compatible = "simple-bus"; + ranges = <0 0x1800c000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + cru@100 { + compatible = "simple-bus"; + reg = <0x100 0x1a4>; + ranges; + #address-cells = <1>; + #size-cells = <1>; + + pin-controller@1c0 { + compatible = "brcm,bcm4708-pinmux"; + reg = <0x1c0 0x24>; + reg-names = "cru_gpio_control"; + + spi-pins { + function = "spi"; + groups = "spi_grp"; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt index ca313a7aeaff..af20b0ec715c 100644 --- a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt @@ -20,16 +20,30 @@ Required properties: - compatible: One of: - "ingenic,jz4740-pinctrl" + - "ingenic,jz4725b-pinctrl" - "ingenic,jz4770-pinctrl" - "ingenic,jz4780-pinctrl" - reg: Address range of the pinctrl registers. -GPIO sub-nodes --------------- +Required properties for sub-nodes (GPIO chips): +----------------------------------------------- -The pinctrl node can have optional sub-nodes for the Ingenic GPIO driver; -please refer to ../gpio/ingenic,gpio.txt. + - compatible: Must contain one of: + - "ingenic,jz4740-gpio" + - "ingenic,jz4770-gpio" + - "ingenic,jz4780-gpio" + - reg: The GPIO bank number. + - interrupt-controller: Marks the device node as an interrupt controller. + - interrupts: Interrupt specifier for the controllers interrupt. + - #interrupt-cells: Should be 2. Refer to + ../interrupt-controller/interrupts.txt for more details. + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the + GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. + - gpio-ranges: Range of pins managed by the GPIO controller. Refer to + ../gpio/gpio.txt for more details. Example: @@ -38,4 +52,21 @@ Example: pinctrl: pin-controller@10010000 { compatible = "ingenic,jz4740-pinctrl"; reg = <0x10010000 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + gpa: gpio@0 { + compatible = "ingenic,jz4740-gpio"; + reg = <0>; + + gpio-controller; + gpio-ranges = <&pinctrl 0 0 32>; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + + interrupt-parent = <&intc>; + interrupts = <28>; + }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index 54ecb8ab7788..82ead40311f6 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -13,6 +13,8 @@ Required properties for the root node: "amlogic,meson-gxl-aobus-pinctrl" "amlogic,meson-axg-periphs-pinctrl" "amlogic,meson-axg-aobus-pinctrl" + "amlogic,meson-g12a-periphs-pinctrl" + "amlogic,meson-g12a-aobus-pinctrl" - reg: address and size of registers controlling irq functionality === GPIO sub-nodes === diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm7xx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm7xx-pinctrl.txt new file mode 100644 index 000000000000..83f4bbac94bb --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm7xx-pinctrl.txt @@ -0,0 +1,216 @@ +Nuvoton NPCM7XX Pin Controllers + +The Nuvoton BMC NPCM7XX Pin Controller multi-function routed through +the multiplexing block, Each pin supports GPIO functionality (GPIOx) +and multiple functions that directly connect the pin to different +hardware blocks. + +Required properties: +- #address-cells : should be 1. +- #size-cells : should be 1. +- compatible : "nuvoton,npcm750-pinctrl" for Poleg NPCM7XX. +- ranges : defines mapping ranges between pin controller node (parent) + to GPIO bank node (children). + +=== GPIO Bank Subnode === + +The NPCM7XX has 8 GPIO Banks each GPIO bank supports 32 GPIO. + +Required GPIO Bank subnode-properties: +- reg : specifies physical base address and size of the GPIO + bank registers. +- gpio-controller : Marks the device node as a GPIO controller. +- #gpio-cells : Must be <2>. The first cell is the gpio pin number + and the second cell is used for optional parameters. +- interrupts : contain the GPIO bank interrupt with flags for falling edge. +- gpio-ranges : defines the range of pins managed by the GPIO bank controller. + +For example, GPIO bank subnodes like the following: + gpio0: gpio@f0010000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x80>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 0 32>; + }; + +=== Pin Mux Subnode === + +- pin: A string containing the name of the pin + An array of strings, each string containing the name of a pin. + These pin are used for selecting pin configuration. + +The following are the list of pins available: + "GPIO0/IOX1DI", "GPIO1/IOX1LD", "GPIO2/IOX1CK", "GPIO3/IOX1D0", + "GPIO4/IOX2DI/SMB1DSDA", "GPIO5/IOX2LD/SMB1DSCL", "GPIO6/IOX2CK/SMB2DSDA", + "GPIO7/IOX2D0/SMB2DSCL", "GPIO8/LKGPO1", "GPIO9/LKGPO2", "GPIO10/IOXHLD", + "GPIO11/IOXHCK", "GPIO12/GSPICK/SMB5BSCL", "GPIO13/GSPIDO/SMB5BSDA", + "GPIO14/GSPIDI/SMB5CSCL", "GPIO15/GSPICS/SMB5CSDA", "GPIO16/LKGPO0", + "GPIO17/PSPI2DI/SMB4DEN","GPIO18/PSPI2D0/SMB4BSDA", "GPIO19/PSPI2CK/SMB4BSCL", + "GPIO20/SMB4CSDA/SMB15SDA", "GPIO21/SMB4CSCL/SMB15SCL", "GPIO22/SMB4DSDA/SMB14SDA", + "GPIO23/SMB4DSCL/SMB14SCL", "GPIO24/IOXHDO", "GPIO25/IOXHDI", "GPIO26/SMB5SDA", + "GPIO27/SMB5SCL", "GPIO28/SMB4SDA", "GPIO29/SMB4SCL", "GPIO30/SMB3SDA", + "GPIO31/SMB3SCL", "GPIO32/nSPI0CS1","SPI0D2", "SPI0D3", "GPIO37/SMB3CSDA", + "GPIO38/SMB3CSCL", "GPIO39/SMB3BSDA", "GPIO40/SMB3BSCL", "GPIO41/BSPRXD", + "GPO42/BSPTXD/STRAP11", "GPIO43/RXD1/JTMS2/BU1RXD", "GPIO44/nCTS1/JTDI2/BU1CTS", + "GPIO45/nDCD1/JTDO2", "GPIO46/nDSR1/JTCK2", "GPIO47/nRI1/JCP_RDY2", + "GPIO48/TXD2/BSPTXD", "GPIO49/RXD2/BSPRXD", "GPIO50/nCTS2", "GPO51/nRTS2/STRAP2", + "GPIO52/nDCD2", "GPO53/nDTR2_BOUT2/STRAP1", "GPIO54/nDSR2", "GPIO55/nRI2", + "GPIO56/R1RXERR", "GPIO57/R1MDC", "GPIO58/R1MDIO", "GPIO59/SMB3DSDA", + "GPIO60/SMB3DSCL", "GPO61/nDTR1_BOUT1/STRAP6", "GPO62/nRTST1/STRAP5", + "GPO63/TXD1/STRAP4", "GPIO64/FANIN0", "GPIO65/FANIN1", "GPIO66/FANIN2", + "GPIO67/FANIN3", "GPIO68/FANIN4", "GPIO69/FANIN5", "GPIO70/FANIN6", "GPIO71/FANIN7", + "GPIO72/FANIN8", "GPIO73/FANIN9", "GPIO74/FANIN10", "GPIO75/FANIN11", + "GPIO76/FANIN12", "GPIO77/FANIN13","GPIO78/FANIN14", "GPIO79/FANIN15", + "GPIO80/PWM0", "GPIO81/PWM1", "GPIO82/PWM2", "GPIO83/PWM3", "GPIO84/R2TXD0", + "GPIO85/R2TXD1", "GPIO86/R2TXEN", "GPIO87/R2RXD0", "GPIO88/R2RXD1", "GPIO89/R2CRSDV", + "GPIO90/R2RXERR", "GPIO91/R2MDC", "GPIO92/R2MDIO", "GPIO93/GA20/SMB5DSCL", + "GPIO94/nKBRST/SMB5DSDA", "GPIO95/nLRESET/nESPIRST", "GPIO96/RG1TXD0", + "GPIO97/RG1TXD1", "GPIO98/RG1TXD2", "GPIO99/RG1TXD3","GPIO100/RG1TXC", + "GPIO101/RG1TXCTL", "GPIO102/RG1RXD0", "GPIO103/RG1RXD1", "GPIO104/RG1RXD2", + "GPIO105/RG1RXD3", "GPIO106/RG1RXC", "GPIO107/RG1RXCTL", "GPIO108/RG1MDC", + "GPIO109/RG1MDIO", "GPIO110/RG2TXD0/DDRV0", "GPIO111/RG2TXD1/DDRV1", + "GPIO112/RG2TXD2/DDRV2", "GPIO113/RG2TXD3/DDRV3", "GPIO114/SMB0SCL", + "GPIO115/SMB0SDA", "GPIO116/SMB1SCL", "GPIO117/SMB1SDA", "GPIO118/SMB2SCL", + "GPIO119/SMB2SDA", "GPIO120/SMB2CSDA", "GPIO121/SMB2CSCL", "GPIO122/SMB2BSDA", + "GPIO123/SMB2BSCL", "GPIO124/SMB1CSDA", "GPIO125/SMB1CSCL","GPIO126/SMB1BSDA", + "GPIO127/SMB1BSCL", "GPIO128/SMB8SCL", "GPIO129/SMB8SDA", "GPIO130/SMB9SCL", + "GPIO131/SMB9SDA", "GPIO132/SMB10SCL", "GPIO133/SMB10SDA","GPIO134/SMB11SCL", + "GPIO135/SMB11SDA", "GPIO136/SD1DT0", "GPIO137/SD1DT1", "GPIO138/SD1DT2", + "GPIO139/SD1DT3", "GPIO140/SD1CLK", "GPIO141/SD1WP", "GPIO142/SD1CMD", + "GPIO143/SD1CD/SD1PWR", "GPIO144/PWM4", "GPIO145/PWM5", "GPIO146/PWM6", + "GPIO147/PWM7", "GPIO148/MMCDT4", "GPIO149/MMCDT5", "GPIO150/MMCDT6", + "GPIO151/MMCDT7", "GPIO152/MMCCLK", "GPIO153/MMCWP", "GPIO154/MMCCMD", + "GPIO155/nMMCCD/nMMCRST", "GPIO156/MMCDT0", "GPIO157/MMCDT1", "GPIO158/MMCDT2", + "GPIO159/MMCDT3", "GPIO160/CLKOUT/RNGOSCOUT", "GPIO161/nLFRAME/nESPICS", + "GPIO162/SERIRQ", "GPIO163/LCLK/ESPICLK", "GPIO164/LAD0/ESPI_IO0", + "GPIO165/LAD1/ESPI_IO1", "GPIO166/LAD2/ESPI_IO2", "GPIO167/LAD3/ESPI_IO3", + "GPIO168/nCLKRUN/nESPIALERT", "GPIO169/nSCIPME", "GPIO170/nSMI", "GPIO171/SMB6SCL", + "GPIO172/SMB6SDA", "GPIO173/SMB7SCL", "GPIO174/SMB7SDA", "GPIO175/PSPI1CK/FANIN19", + "GPIO176/PSPI1DO/FANIN18", "GPIO177/PSPI1DI/FANIN17", "GPIO178/R1TXD0", + "GPIO179/R1TXD1", "GPIO180/R1TXEN", "GPIO181/R1RXD0", "GPIO182/R1RXD1", + "GPIO183/SPI3CK", "GPO184/SPI3D0/STRAP9", "GPO185/SPI3D1/STRAP10", + "GPIO186/nSPI3CS0", "GPIO187/nSPI3CS1", "GPIO188/SPI3D2/nSPI3CS2", + "GPIO189/SPI3D3/nSPI3CS3", "GPIO190/nPRD_SMI", "GPIO191", "GPIO192", "GPIO193/R1CRSDV", + "GPIO194/SMB0BSCL", "GPIO195/SMB0BSDA", "GPIO196/SMB0CSCL", "GPIO197/SMB0DEN", + "GPIO198/SMB0DSDA", "GPIO199/SMB0DSCL", "GPIO200/R2CK", "GPIO201/R1CK", + "GPIO202/SMB0CSDA", "GPIO203/FANIN16", "GPIO204/DDC2SCL", "GPIO205/DDC2SDA", + "GPIO206/HSYNC2", "GPIO207/VSYNC2", "GPIO208/RG2TXC/DVCK", "GPIO209/RG2TXCTL/DDRV4", + "GPIO210/RG2RXD0/DDRV5", "GPIO211/RG2RXD1/DDRV6", "GPIO212/RG2RXD2/DDRV7", + "GPIO213/RG2RXD3/DDRV8", "GPIO214/RG2RXC/DDRV9", "GPIO215/RG2RXCTL/DDRV10", + "GPIO216/RG2MDC/DDRV11", "GPIO217/RG2MDIO/DVHSYNC", "GPIO218/nWDO1", + "GPIO219/nWDO2", "GPIO220/SMB12SCL", "GPIO221/SMB12SDA", "GPIO222/SMB13SCL", + "GPIO223/SMB13SDA", "GPIO224/SPIXCK", "GPO225/SPIXD0/STRAP12", "GPO226/SPIXD1/STRAP13", + "GPIO227/nSPIXCS0", "GPIO228/nSPIXCS1", "GPO229/SPIXD2/STRAP3", "GPIO230/SPIXD3", + "GPIO231/nCLKREQ", "GPI255/DACOSEL" + +Optional Properties: + bias-disable, bias-pull-down, bias-pull-up, input-enable, + input-disable, output-high, output-low, drive-push-pull, + drive-open-drain, input-debounce, slew-rate, drive-strength + + slew-rate valid arguments are: + <0> - slow + <1> - fast + drive-strength valid arguments are: + <2> - 2mA + <4> - 4mA + <8> - 8mA + <12> - 12mA + <16> - 16mA + <24> - 24mA + +For example, pinctrl might have pinmux subnodes like the following: + + gpio0_iox1d1_pin: gpio0-iox1d1-pin { + pins = "GPIO0/IOX1DI"; + output-high; + }; + gpio0_iox1ck_pin: gpio0-iox1ck-pin { + pins = "GPIO2/IOX1CK"; + output_high; + }; + +=== Pin Group Subnode === + +Required pin group subnode-properties: +- groups : A string containing the name of the group to mux. +- function: A string containing the name of the function to mux to the + group. + +The following are the list of the available groups and functions : + smb0, smb0b, smb0c, smb0d, smb0den, smb1, smb1b, smb1c, smb1d, + smb2, smb2b, smb2c, smb2d, smb3, smb3b, smb3c, smb3d, smb4, smb4b, + smb4c, smb4d, smb4den, smb5, smb5b, smb5c, smb5d, ga20kbc, smb6, + smb7, smb8, smb9, smb10, smb11, smb12, smb13, smb14, smb15, fanin0, + fanin1, fanin2, fanin3, fanin4, fanin5, fanin6, fanin7, fanin8, + fanin9, fanin10, fanin11 fanin12 fanin13, fanin14, fanin15, faninx, + pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, pwm6, pwm7, rg1, rg1mdio, rg2, + rg2mdio, ddr, uart1, uart2, bmcuart0a, bmcuart0b, bmcuart1, iox1, + iox2, ioxh, gspi, mmc, mmcwp, mmccd, mmcrst, mmc8, r1, r1err, r1md, + r2, r2err, r2md, sd1, sd1pwr, wdog1, wdog2, scipme, sci, serirq, + jtag2, spix, spixcs1, pspi1, pspi2, ddc, clkreq, clkout, spi3, spi3cs1, + spi3quad, spi3cs2, spi3cs3, spi0cs1, lpc, lpcclk, espi, lkgpo0, lkgpo1, + lkgpo2, nprd_smi + +For example, pinctrl might have group subnodes like the following: + r1err_pins: r1err-pins { + groups = "r1err"; + function = "r1err"; + }; + r1md_pins: r1md-pins { + groups = "r1md"; + function = "r1md"; + }; + r1_pins: r1-pins { + groups = "r1"; + function = "r1"; + }; + +Examples +======== +pinctrl: pinctrl@f0800000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "nuvoton,npcm750-pinctrl"; + ranges = <0 0xf0010000 0x8000>; + + gpio0: gpio@f0010000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x80>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 0 32>; + }; + + .... + + gpio7: gpio@f0017000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x7000 0x80>; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 224 32>; + }; + + gpio0_iox1d1_pin: gpio0-iox1d1-pin { + pins = "GPIO0/IOX1DI"; + output-high; + }; + + iox1_pins: iox1-pins { + groups = "iox1"; + function = "iox1"; + }; + iox2_pins: iox2-pins { + groups = "iox2"; + function = "iox2"; + }; + + .... + + clkreq_pins: clkreq-pins { + groups = "clkreq"; + function = "clkreq"; + }; +};
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt index ffd4345415f3..ab4000eab07d 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt @@ -19,6 +19,7 @@ PMIC's from Qualcomm. "qcom,pm8998-gpio" "qcom,pma8084-gpio" "qcom,pmi8994-gpio" + "qcom,pms405-gpio" And must contain either "qcom,spmi-gpio" or "qcom,ssbi-gpio" if the device is on an spmi bus or an ssbi bus respectively @@ -91,6 +92,7 @@ to specify in a pin configuration subnode: gpio1-gpio26 for pm8998 gpio1-gpio22 for pma8084 gpio1-gpio10 for pmi8994 + gpio1-gpio11 for pms405 - function: Usage: required diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt new file mode 100644 index 000000000000..2b8f77762edc --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt @@ -0,0 +1,199 @@ +Qualcomm QCS404 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +QCS404 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,qcs404-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the north, south and east TLMM + tiles. + +- reg-names: + Usage: required + Value type: <stringlist> + Defintiion: names for the cells of reg, must contain "north", "south" + and "east". + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +- gpio-ranges: + Usage: required + Definition: see ../gpio/gpio.txt + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. + + Valid pins are: + gpio0-gpio119 + Supports mux, bias and drive-strength + + sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, + sdc2_data + Supports bias and drive-strength + + ufs_reset + Supports bias and drive-strength + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + + gpio, hdmi_tx, hdmi_ddc, blsp_uart_tx_a2, blsp_spi2, m_voc, + qdss_cti_trig_in_a0, blsp_uart_rx_a2, qdss_tracectl_a, + blsp_uart2, aud_cdc, blsp_i2c_sda_a2, qdss_tracedata_a, + blsp_i2c_scl_a2, qdss_tracectl_b, qdss_cti_trig_in_b0, + blsp_uart1, blsp_spi_mosi_a1, blsp_spi_miso_a1, + qdss_tracedata_b, blsp_i2c1, blsp_spi_cs_n_a1, gcc_plltest, + blsp_spi_clk_a1, rgb_data0, blsp_uart5, blsp_spi5, + adsp_ext, rgb_data1, prng_rosc, rgb_data2, blsp_i2c5, + gcc_gp1_clk_b, rgb_data3, gcc_gp2_clk_b, blsp_spi0, + blsp_uart0, gcc_gp3_clk_b, blsp_i2c0, qdss_traceclk_b, + pcie_clk, nfc_irq, blsp_spi4, nfc_dwl, audio_ts, rgb_data4, + spi_lcd, blsp_uart_tx_b2, gcc_gp3_clk_a, rgb_data5, + blsp_uart_rx_b2, blsp_i2c_sda_b2, blsp_i2c_scl_b2, + pwm_led11, i2s_3_data0_a, ebi2_lcd, i2s_3_data1_a, + i2s_3_data2_a, atest_char, pwm_led3, i2s_3_data3_a, + pwm_led4, i2s_4, ebi2_a, dsd_clk_b, pwm_led5, pwm_led6, + pwm_led7, pwm_led8, pwm_led24, spkr_dac0, blsp_i2c4, + pwm_led9, pwm_led10, spdifrx_opt, pwm_led12, pwm_led13, + pwm_led14, wlan1_adc1, rgb_data_b0, pwm_led15, + blsp_spi_mosi_b1, wlan1_adc0, rgb_data_b1, pwm_led16, + blsp_spi_miso_b1, qdss_cti_trig_out_b0, wlan2_adc1, + rgb_data_b2, pwm_led17, blsp_spi_cs_n_b1, wlan2_adc0, + rgb_data_b3, pwm_led18, blsp_spi_clk_b1, rgb_data_b4, + pwm_led19, ext_mclk1_b, qdss_traceclk_a, rgb_data_b5, + pwm_led20, atest_char3, i2s_3_sck_b, ldo_update, bimc_dte0, + rgb_hsync, pwm_led21, i2s_3_ws_b, dbg_out, rgb_vsync, + i2s_3_data0_b, ldo_en, hdmi_dtest, rgb_de, i2s_3_data1_b, + hdmi_lbk9, rgb_clk, atest_char1, i2s_3_data2_b, ebi_cdc, + hdmi_lbk8, rgb_mdp, atest_char0, i2s_3_data3_b, hdmi_lbk7, + rgb_data_b6, rgb_data_b7, hdmi_lbk6, rgmii_int, cri_trng1, + rgmii_wol, cri_trng0, gcc_tlmm, rgmii_ck, rgmii_tx, + hdmi_lbk5, hdmi_pixel, hdmi_rcv, hdmi_lbk4, rgmii_ctl, + ext_lpass, rgmii_rx, cri_trng, hdmi_lbk3, hdmi_lbk2, + qdss_cti_trig_out_b1, rgmii_mdio, hdmi_lbk1, rgmii_mdc, + hdmi_lbk0, ir_in, wsa_en, rgb_data6, rgb_data7, + atest_char2, ebi_ch0, blsp_uart3, blsp_spi3, sd_write, + blsp_i2c3, gcc_gp1_clk_a, qdss_cti_trig_in_b1, + gcc_gp2_clk_a, ext_mclk0, mclk_in1, i2s_1, dsd_clk_a, + qdss_cti_trig_in_a1, rgmi_dll1, pwm_led22, pwm_led23, + qdss_cti_trig_out_a0, rgmi_dll2, pwm_led1, + qdss_cti_trig_out_a1, pwm_led2, i2s_2, pll_bist, + ext_mclk1_a, mclk_in2, bimc_dte1, i2s_3_sck_a, i2s_3_ws_a + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@1000000 { + compatible = "qcom,qcs404-pinctrl"; + reg = <0x01000000 0x200000>, + <0x01300000 0x200000>, + <0x07b00000 0x200000>; + reg-names = "south", "north", "east"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 120>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt new file mode 100644 index 000000000000..769ca83bb40d --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt @@ -0,0 +1,191 @@ +Qualcomm Technologies, Inc. SDM660 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +SDM660 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,sdm660-pinctrl" or + "qcom,sdm630-pinctrl". + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the north, center and south + TLMM tiles. + +- reg-names: + Usage: required + Value type: <stringlist> + Definition: names for the cells of reg, must contain "north", "center" + and "south". + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- gpio-ranges: + Usage: required + Value type: <prop-encoded-array> + Definition: Specifies the mapping between gpio controller and + pin-controller pins. + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. Valid pins are: + gpio0-gpio113, + Supports mux, bias and drive-strength + sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd, sdc2_data sdc1_rclk, + Supports bias and drive-strength + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + adsp_ext, agera_pll, atest_char, atest_char0, atest_char1, + atest_char2, atest_char3, atest_gpsadc0, atest_gpsadc1, + atest_tsens, atest_tsens2, atest_usb1, atest_usb10, + atest_usb11, atest_usb12, atest_usb13, atest_usb2, + atest_usb20, atest_usb21, atest_usb22, atest_usb23, + audio_ref, bimc_dte0, bimc_dte1, blsp_i2c1, blsp_i2c2, + blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, + blsp_i2c8_a, blsp_i2c8_b, blsp_spi1, blsp_spi2, blsp_spi3, + blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi4, blsp_spi5, + blsp_spi6, blsp_spi7, blsp_spi8_a, blsp_spi8_b, + blsp_spi8_cs1, blsp_spi8_cs2, blsp_uart1, blsp_uart2, + blsp_uart5, blsp_uart6_a, blsp_uart6_b, blsp_uim1, + blsp_uim2, blsp_uim5, blsp_uim6, cam_mclk, cci_async, + cci_i2c, cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist, + gcc_gp1, gcc_gp2, gcc_gp3, gpio, gps_tx_a, gps_tx_b, gps_tx_c, + isense_dbg, jitter_bist, ldo_en, ldo_update, m_voc, mdp_vsync, + mdss_vsync0, mdss_vsync1, mdss_vsync2, mdss_vsync3, mss_lte, + nav_pps_a, nav_pps_b, nav_pps_c, pa_indicator, phase_flag0, + phase_flag1, phase_flag10, phase_flag11, phase_flag12, + phase_flag13, phase_flag14, phase_flag15, phase_flag16, + phase_flag17, phase_flag18, phase_flag19, phase_flag2, + phase_flag20, phase_flag21, phase_flag22, phase_flag23, + phase_flag24, phase_flag25, phase_flag26, phase_flag27, + phase_flag28, phase_flag29, phase_flag3, phase_flag30, + phase_flag31, phase_flag4, phase_flag5, phase_flag6, + phase_flag7, phase_flag8, phase_flag9, pll_bypassnl, + pll_reset, pri_mi2s, pri_mi2s_ws, prng_rosc, pwr_crypto, + pwr_modem, pwr_nav, qdss_cti0_a, qdss_cti0_b, qdss_cti1_a, + qdss_cti1_b, qdss_gpio, qdss_gpio0, qdss_gpio1, qdss_gpio10, + qdss_gpio11, qdss_gpio12, qdss_gpio13, qdss_gpio14, qdss_gpio15, + qdss_gpio2, qdss_gpio3, qdss_gpio4, qdss_gpio5, qdss_gpio6, + qdss_gpio7, qdss_gpio8, qdss_gpio9, qlink_enable, qlink_request, + qspi_clk, qspi_cs, qspi_data0, qspi_data1, qspi_data2, + qspi_data3, qspi_resetn, sec_mi2s, sndwire_clk, sndwire_data, + sp_cmu, ssc_irq, tgu_ch0, tgu_ch1, tsense_pwm1, tsense_pwm2, + uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk, + uim2_data, uim2_present, uim2_reset, uim_batt, vfr_1, + vsense_clkout, vsense_data0, vsense_data1, vsense_mode, + wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1 + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@3100000 { + compatible = "qcom,sdm660-pinctrl"; + reg = <0x3100000 0x200000>, + <0x3500000 0x200000>, + <0x3900000 0x200000>; + reg-names = "south", "center", "north"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + gpio-ranges = <&tlmm 0 0 114>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index abd8fbcf1e62..3902efa18fd0 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -14,8 +14,11 @@ Required Properties: - "renesas,pfc-r8a73a4": for R8A73A4 (R-Mobile APE6) compatible pin-controller. - "renesas,pfc-r8a7740": for R8A7740 (R-Mobile A1) compatible pin-controller. - "renesas,pfc-r8a7743": for R8A7743 (RZ/G1M) compatible pin-controller. + - "renesas,pfc-r8a7744": for R8A7744 (RZ/G1N) compatible pin-controller. - "renesas,pfc-r8a7745": for R8A7745 (RZ/G1E) compatible pin-controller. - "renesas,pfc-r8a77470": for R8A77470 (RZ/G1C) compatible pin-controller. + - "renesas,pfc-r8a774a1": for R8A774A1 (RZ/G2M) compatible pin-controller. + - "renesas,pfc-r8a774c0": for R8A774C0 (RZ/G2E) compatible pin-controller. - "renesas,pfc-r8a7778": for R8A7778 (R-Car M1) compatible pin-controller. - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller. - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller. diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.txt new file mode 100644 index 000000000000..25e53acd523e --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.txt @@ -0,0 +1,153 @@ +Renesas RZ/N1 SoC Pinctrl node description. + +Pin controller node +------------------- +Required properties: +- compatible: SoC-specific compatible string "renesas,<soc-specific>-pinctrl" + followed by "renesas,rzn1-pinctrl" as fallback. The SoC-specific compatible + strings must be one of: + "renesas,r9a06g032-pinctrl" for RZ/N1D + "renesas,r9a06g033-pinctrl" for RZ/N1S +- reg: Address base and length of the memory area where the pin controller + hardware is mapped to. +- clocks: phandle for the clock, see the description of clock-names below. +- clock-names: Contains the name of the clock: + "bus", the bus clock, sometimes described as pclk, for register accesses. + +Example: + pinctrl: pin-controller@40067000 { + compatible = "renesas,r9a06g032-pinctrl", "renesas,rzn1-pinctrl"; + reg = <0x40067000 0x1000>, <0x51000000 0x480>; + clocks = <&sysctrl R9A06G032_HCLK_PINCONFIG>; + clock-names = "bus"; + }; + +Sub-nodes +--------- + +The child nodes of the pin controller node describe a pin multiplexing +function. + +- Pin multiplexing sub-nodes: + A pin multiplexing sub-node describes how to configure a set of + (or a single) pin in some desired alternate function mode. + A single sub-node may define several pin configurations. + Please refer to pinctrl-bindings.txt to get to know more on generic + pin properties usage. + + The allowed generic formats for a pin multiplexing sub-node are the + following ones: + + node-1 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + + node-2 { + sub-node-1 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + + sub-node-2 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + + ... + + sub-node-n { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + }; + + node-3 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + + sub-node-1 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + + ... + + sub-node-n { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + }; + + Use the latter two formats when pins part of the same logical group need to + have different generic pin configuration flags applied. Note that the generic + pinconfig in node-3 does not apply to the sub-nodes. + + Client sub-nodes shall refer to pin multiplexing sub-nodes using the phandle + of the most external one. + + Eg. + + client-1 { + ... + pinctrl-0 = <&node-1>; + ... + }; + + client-2 { + ... + pinctrl-0 = <&node-2>; + ... + }; + + Required properties: + - pinmux: + integer array representing pin number and pin multiplexing configuration. + When a pin has to be configured in alternate function mode, use this + property to identify the pin by its global index, and provide its + alternate function configuration number along with it. + When multiple pins are required to be configured as part of the same + alternate function they shall be specified as members of the same + argument list of a single "pinmux" property. + Integers values in the "pinmux" argument list are assembled as: + (PIN | MUX_FUNC << 8) + where PIN directly corresponds to the pl_gpio pin number and MUX_FUNC is + one of the alternate function identifiers defined in: + <include/dt-bindings/pinctrl/rzn1-pinctrl.h> + These identifiers collapse the IO Multiplex Configuration Level 1 and + Level 2 numbers that are detailed in the hardware reference manual into a + single number. The identifiers for Level 2 are simply offset by 10. + Additional identifiers are provided to specify the MDIO source peripheral. + + Optional generic pinconf properties: + - bias-disable - disable any pin bias + - bias-pull-up - pull up the pin with 50 KOhm + - bias-pull-down - pull down the pin with 50 KOhm + - bias-high-impedance - high impedance mode + - drive-strength - sink or source at most 4, 6, 8 or 12 mA + + Example: + A serial communication interface with a TX output pin and an RX input pin. + + &pinctrl { + pins_uart0: pins_uart0 { + pinmux = < + RZN1_PINMUX(103, RZN1_FUNC_UART0_I) /* UART0_TXD */ + RZN1_PINMUX(104, RZN1_FUNC_UART0_I) /* UART0_RXD */ + >; + }; + }; + + Example 2: + Here we set the pull up on the RXD pin of the UART. + + &pinctrl { + pins_uart0: pins_uart0 { + pinmux = <RZN1_PINMUX(103, RZN1_FUNC_UART0_I)>; /* TXD */ + + pins_uart6_rx { + pinmux = <RZN1_PINMUX(104, RZN1_FUNC_UART0_I)>; /* RXD */ + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/power/reset/qcom,pon.txt b/Documentation/devicetree/bindings/power/reset/qcom,pon.txt index 651491bb63b7..5705f575862d 100644 --- a/Documentation/devicetree/bindings/power/reset/qcom,pon.txt +++ b/Documentation/devicetree/bindings/power/reset/qcom,pon.txt @@ -6,7 +6,10 @@ and resin along with the Android reboot-mode. This DT node has pwrkey and resin as sub nodes. Required Properties: --compatible: "qcom,pm8916-pon" +-compatible: Must be one of: + "qcom,pm8916-pon" + "qcom,pms405-pon" + -reg: Specifies the physical address of the pon register Optional subnode: diff --git a/Documentation/devicetree/bindings/power/supply/bq25890.txt b/Documentation/devicetree/bindings/power/supply/bq25890.txt index c9dd17d142ad..dc0568933359 100644 --- a/Documentation/devicetree/bindings/power/supply/bq25890.txt +++ b/Documentation/devicetree/bindings/power/supply/bq25890.txt @@ -1,5 +1,8 @@ Binding for TI bq25890 Li-Ion Charger +This driver will support the bq25896 and the bq25890. There are other ICs +in the same family but those have not been tested. + Required properties: - compatible: Should contain one of the following: * "ti,bq25890" diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt index 37994fdb18ca..4fa8e08df2b6 100644 --- a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt +++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt @@ -23,6 +23,7 @@ Required properties: * "ti,bq27546" - BQ27546 * "ti,bq27742" - BQ27742 * "ti,bq27545" - BQ27545 + * "ti,bq27411" - BQ27411 * "ti,bq27421" - BQ27421 * "ti,bq27425" - BQ27425 * "ti,bq27426" - BQ27426 diff --git a/Documentation/devicetree/bindings/power/supply/sc2731_charger.txt b/Documentation/devicetree/bindings/power/supply/sc2731_charger.txt new file mode 100644 index 000000000000..5266fab16575 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sc2731_charger.txt @@ -0,0 +1,40 @@ +Spreadtrum SC2731 PMIC battery charger binding + +Required properties: + - compatible: Should be "sprd,sc2731-charger". + - reg: Address offset of charger register. + - phys: Contains a phandle to the USB phy. + +Optional Properties: +- monitored-battery: phandle of battery characteristics devicetree node. + The charger uses the following battery properties: +- charge-term-current-microamp: current for charge termination phase. +- constant-charge-voltage-max-microvolt: maximum constant input voltage. + See Documentation/devicetree/bindings/power/supply/battery.txt + +Example: + + bat: battery { + compatible = "simple-battery"; + charge-term-current-microamp = <120000>; + constant-charge-voltage-max-microvolt = <4350000>; + ...... + }; + + sc2731_pmic: pmic@0 { + compatible = "sprd,sc2731"; + reg = <0>; + spi-max-frequency = <26000000>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + + charger@0 { + compatible = "sprd,sc2731-charger"; + reg = <0x0>; + phys = <&ssphy>; + monitored-battery = <&bat>; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt index c7610718adff..f9be1acf891c 100644 --- a/Documentation/devicetree/bindings/regulator/pfuze100.txt +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -12,6 +12,11 @@ Optional properties: disabled. This binding is a workaround to keep backward compatibility with old dtb's which rely on the fact that the switched regulators are always on and don't mark them explicit as "regulator-always-on". +- fsl,pmic-stby-poweroff: if present, configure the PMIC to shutdown all + power rails when PMIC_STBY_REQ line is asserted during the power off sequence. + Use this option if the SoC should be powered off by external power + management IC (PMIC) on PMIC_STBY_REQ signal. + As opposite to PMIC_STBY_REQ boards can implement PMIC_ON_REQ signal. Required child node: - regulators: This is the list of child nodes that specify the regulator diff --git a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt index 58a1d97972f5..45025b5b67f6 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt @@ -26,6 +26,7 @@ Regulator nodes are identified by their compatible: "qcom,rpm-pm8998-regulators" "qcom,rpm-pma8084-regulators" "qcom,rpm-pmi8998-regulators" + "qcom,rpm-pms405-regulators" - vdd_s1-supply: - vdd_s2-supply: @@ -188,6 +189,24 @@ Regulator nodes are identified by their compatible: Definition: reference to regulator supplying the input pin, as described in the data sheet +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_l1_l2-supply: +- vdd_l3_l8-supply: +- vdd_l4-supply: +- vdd_l5_l6-supply: +- vdd_l7-supply: +- vdd_l3_l8-supply: +- vdd_l9-supply: +- vdd_l10_l11_l12_l13-supply: + Usage: optional (pms405 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each of the pmics below. @@ -222,6 +241,10 @@ pma8084: pmi8998: bob +pms405: + s1, s2, s3, s4, s5, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, + l13 + The content of each sub-node is defined by the standard binding for regulators - see regulator.txt. diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt index 76ead07072b1..4b98ca26e61a 100644 --- a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt @@ -1,7 +1,9 @@ -ROHM BD71837 Power Management Integrated Circuit (PMIC) regulator bindings +ROHM BD71837 and BD71847 Power Management Integrated Circuit regulator bindings Required properties: - - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7" + - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7" for + BD71837. For BD71847 names should be "buck1", ..., "buck6" + and "ldo1", ..., "ldo6" List of regulators provided by this controller. BD71837 regulators node should be sub node of the BD71837 MFD node. See BD71837 MFD bindings at @@ -16,10 +18,14 @@ disabled by driver at startup. LDO5 and LDO6 are supplied by those and if they are disabled at startup the voltage monitoring for LDO5/LDO6 will cause PMIC to reset. -The valid names for regulator nodes are: +The valid names for BD71837 regulator nodes are: BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, BUCK7, BUCK8 LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7 +The valid names for BD71847 regulator nodes are: +BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6 +LDO1, LDO2, LDO3, LDO4, LDO5, LDO6 + Optional properties: - Any optional property defined in bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt new file mode 100644 index 000000000000..a3f476240565 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt @@ -0,0 +1,68 @@ +STMicroelectronics STPMIC1 Voltage regulators + +Regulator Nodes are optional depending on needs. + +Available Regulators in STPMIC1 device are: + - buck1 for Buck BUCK1 + - buck2 for Buck BUCK2 + - buck3 for Buck BUCK3 + - buck4 for Buck BUCK4 + - ldo1 for LDO LDO1 + - ldo2 for LDO LDO2 + - ldo3 for LDO LDO3 + - ldo4 for LDO LDO4 + - ldo5 for LDO LDO5 + - ldo6 for LDO LDO6 + - vref_ddr for LDO Vref DDR + - boost for Buck BOOST + - pwr_sw1 for VBUS_OTG switch + - pwr_sw2 for SW_OUT switch + +Switches are fixed voltage regulators with only enable/disable capability. + +Optional properties: +- st,mask-reset: mask reset for this regulator: the regulator configuration + is maintained during pmic reset. +- regulator-pull-down: enable high pull down + if not specified light pull down is used +- regulator-over-current-protection: + if set, all regulators are switched off in case of over-current detection + on this regulator, + if not set, the driver only sends an over-current event. +- interrupt-parent: phandle to the parent interrupt controller +- interrupts: index of current limit detection interrupt +- <regulator>-supply: phandle to the parent supply/regulator node + each regulator supply can be described except vref_ddr. + +Example: +regulators { + compatible = "st,stpmic1-regulators"; + + ldo6-supply = <&v3v3>; + + vdd_core: buck1 { + regulator-name = "vdd_core"; + interrupts = <IT_CURLIM_BUCK1 0>; + interrupt-parent = <&pmic>; + st,mask-reset; + regulator-pull-down; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1200000>; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + interrupts = <IT_CURLIM_BUCK4 0>; + interrupt-parent = <&mypmic>; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + v1v8: ldo6 { + regulator-name = "v1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-over-current-protection; + }; +}; diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt index 03c741602c6d..6d2dd8a31482 100644 --- a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt @@ -98,6 +98,12 @@ The property below is dependent on fsl,tdm-interface: usage: optional for tdm interface value type: <empty> Definition : Internal loopback connecting on TDM layer. +- fsl,hmask + usage: optional + Value type: <u16> + Definition: HDLC address recognition. Set to zero to disable + address filtering of packets: + fsl,hmask = /bits/ 16 <0x0000>; Example for tdm interface: diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt index ff92e5a41bed..dab7ca9f250c 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt @@ -53,20 +53,8 @@ Required properties: - clocks: Serial engine core clock needed by the device. Qualcomm Technologies Inc. GENI Serial Engine based SPI Controller - -Required properties: -- compatible: Must contain "qcom,geni-spi". -- reg: Must contain SPI register location and length. -- interrupts: Must contain SPI controller interrupts. -- clock-names: Must contain "se". -- clocks: Serial engine core clock needed by the device. -- spi-max-frequency: Specifies maximum SPI clock frequency, units - Hz. -- #address-cells: Must be <1> to define a chip select address on - the SPI bus. -- #size-cells: Must be <0>. - -SPI slave nodes must be children of the SPI master node and conform to SPI bus -binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt. +node binding is described in +Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt. Example: geniqup@8c0000 { @@ -103,17 +91,4 @@ Example: pinctrl-1 = <&qup_1_uart_3_sleep>; }; - spi0: spi@a84000 { - compatible = "qcom,geni-spi"; - reg = <0xa84000 0x4000>; - interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "se"; - clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&qup_1_spi_2_active>; - pinctrl-1 = <&qup_1_spi_2_sleep>; - spi-max-frequency = <19200000>; - #address-cells = <1>; - #size-cells = <0>; - }; } diff --git a/Documentation/devicetree/bindings/sound/adi,adau1977.txt b/Documentation/devicetree/bindings/sound/adi,adau1977.txt new file mode 100644 index 000000000000..e79aeef73f28 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/adi,adau1977.txt @@ -0,0 +1,54 @@ +Analog Devices ADAU1977/ADAU1978/ADAU1979 + +Datasheets: +http://www.analog.com/media/en/technical-documentation/data-sheets/ADAU1977.pdf +http://www.analog.com/media/en/technical-documentation/data-sheets/ADAU1978.pdf +http://www.analog.com/media/en/technical-documentation/data-sheets/ADAU1979.pdf + +This driver supports both the I2C and SPI bus. + +Required properties: + - compatible: Should contain one of the following: + "adi,adau1977" + "adi,adau1978" + "adi,adau1979" + + - AVDD-supply: analog power supply for the device, please consult + Documentation/devicetree/bindings/regulator/regulator.txt + +Optional properties: + - reset-gpio: the reset pin for the chip, for more details consult + Documentation/devicetree/bindings/gpio/gpio.txt + + - DVDD-supply: supply voltage for the digital core, please consult + Documentation/devicetree/bindings/regulator/regulator.txt + +For required properties on SPI, please consult +Documentation/devicetree/bindings/spi/spi-bus.txt + +Required properties on I2C: + + - reg: The i2c address. Value depends on the state of ADDR0 + and ADDR1, as wired in hardware. + +Examples: + + adau1977_spi: adau1977@0 { + compatible = "adi,adau1977"; + spi-max-frequency = <600000>; + + AVDD-supply = <®ulator>; + DVDD-supply = <®ulator_digital>; + + reset_gpio = <&gpio 10 GPIO_ACTIVE_LOW>; + }; + + adau1977_i2c: adau1977@11 { + compatible = "adi,adau1977"; + reg = <0x11>; + + AVDD-supply = <®ulator>; + DVDD-supply = <®ulator_digital>; + + reset_gpio = <&gpio 10 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt new file mode 100644 index 000000000000..5672d0bc5b16 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt @@ -0,0 +1,24 @@ +* Amlogic Audio PDM input + +Required properties: +- compatible: 'amlogic,axg-pdm' +- reg: physical base address of the controller and length of memory + mapped region. +- clocks: list of clock phandle, one for each entry clock-names. +- clock-names: should contain the following: + * "pclk" : peripheral clock. + * "dclk" : pdm digital clock + * "sysclk" : dsp system clock +- #sound-dai-cells: must be 0. + +Example of PDM on the A113 SoC: + +pdm: audio-controller@ff632000 { + compatible = "amlogic,axg-pdm"; + reg = <0x0 0xff632000 0x0 0x34>; + #sound-dai-cells = <0>; + clocks = <&clkc_audio AUD_CLKID_PDM>, + <&clkc_audio AUD_CLKID_PDM_DCLK>, + <&clkc_audio AUD_CLKID_PDM_SYSCLK>; + clock-names = "pclk", "dclk", "sysclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/cs42l51.txt b/Documentation/devicetree/bindings/sound/cs42l51.txt new file mode 100644 index 000000000000..4b5de33ce377 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs42l51.txt @@ -0,0 +1,17 @@ +CS42L51 audio CODEC + +Optional properties: + + - clocks : a list of phandles + clock-specifiers, one for each entry in + clock-names + + - clock-names : must contain "MCLK" + +Example: + +cs42l51: cs42l51@4a { + compatible = "cirrus,cs42l51"; + reg = <0x4a>; + clocks = <&mclk_prov>; + clock-names = "MCLK"; +}; diff --git a/Documentation/devicetree/bindings/sound/maxim,max98088.txt b/Documentation/devicetree/bindings/sound/maxim,max98088.txt new file mode 100644 index 000000000000..da764d913319 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/maxim,max98088.txt @@ -0,0 +1,23 @@ +MAX98088 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible: "maxim,max98088" or "maxim,max98089". +- reg: The I2C address of the device. + +Optional properties: + +- clocks: the clock provider of MCLK, see ../clock/clock-bindings.txt section + "consumer" for more information. +- clock-names: must be set to "mclk" + +Example: + +max98089: codec@10 { + compatible = "maxim,max98089"; + reg = <0x10>; + clocks = <&clks IMX6QDL_CLK_CKO2>; + clock-names = "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/mikroe,mikroe-proto.txt b/Documentation/devicetree/bindings/sound/mikroe,mikroe-proto.txt new file mode 100644 index 000000000000..912f8fae11c5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mikroe,mikroe-proto.txt @@ -0,0 +1,23 @@ +Mikroe-PROTO audio board + +Required properties: + - compatible: "mikroe,mikroe-proto" + - dai-format: Must be "i2s". + - i2s-controller: The phandle of the I2S controller. + - audio-codec: The phandle of the WM8731 audio codec. +Optional properties: + - model: The user-visible name of this sound complex. + - bitclock-master: Indicates dai-link bit clock master; for details see simple-card.txt (1). + - frame-master: Indicates dai-link frame master; for details see simple-card.txt (1). + +(1) : There must be the same master for both bit and frame clocks. + +Example: + sound { + compatible = "mikroe,mikroe-proto"; + model = "wm8731 @ sama5d2_xplained"; + i2s-controller = <&i2s0>; + audio-codec = <&wm8731>; + dai-format = "i2s"; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/nau8822.txt b/Documentation/devicetree/bindings/sound/nau8822.txt new file mode 100644 index 000000000000..a471d162d4e5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nau8822.txt @@ -0,0 +1,16 @@ +NAU8822 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "nuvoton,nau8822" + + - reg : the I2C address of the device. + +Example: + +codec: nau8822@1a { + compatible = "nuvoton,nau8822"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/pcm3060.txt b/Documentation/devicetree/bindings/sound/pcm3060.txt new file mode 100644 index 000000000000..90fcb8523099 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/pcm3060.txt @@ -0,0 +1,17 @@ +PCM3060 audio CODEC + +This driver supports both I2C and SPI. + +Required properties: + +- compatible: "ti,pcm3060" + +- reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Examples: + + pcm3060: pcm3060@46 { + compatible = "ti,pcm3060"; + reg = <0x46>; + }; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6afe.txt b/Documentation/devicetree/bindings/sound/qcom,q6afe.txt index a8179409c194..d74888b9f1bb 100644 --- a/Documentation/devicetree/bindings/sound/qcom,q6afe.txt +++ b/Documentation/devicetree/bindings/sound/qcom,q6afe.txt @@ -49,7 +49,7 @@ configuration of each dai. Must contain the following properties. Usage: required for mi2s interface Value type: <prop-encoded-array> Definition: Must be list of serial data lines used by this dai. - should be one or more of the 1-4 sd lines. + should be one or more of the 0-3 sd lines. - qcom,tdm-sync-mode: Usage: required for tdm interface @@ -137,42 +137,42 @@ q6afe@4 { prim-mi2s-rx@16 { reg = <16>; - qcom,sd-lines = <1 3>; + qcom,sd-lines = <0 2>; }; prim-mi2s-tx@17 { reg = <17>; - qcom,sd-lines = <2>; + qcom,sd-lines = <1>; }; sec-mi2s-rx@18 { reg = <18>; - qcom,sd-lines = <1 4>; + qcom,sd-lines = <0 3>; }; sec-mi2s-tx@19 { reg = <19>; - qcom,sd-lines = <2>; + qcom,sd-lines = <1>; }; tert-mi2s-rx@20 { reg = <20>; - qcom,sd-lines = <2 4>; + qcom,sd-lines = <1 3>; }; tert-mi2s-tx@21 { reg = <21>; - qcom,sd-lines = <1>; + qcom,sd-lines = <0>; }; quat-mi2s-rx@22 { reg = <22>; - qcom,sd-lines = <1>; + qcom,sd-lines = <0>; }; quat-mi2s-tx@23 { reg = <23>; - qcom,sd-lines = <2>; + qcom,sd-lines = <1>; }; }; }; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index 9e764270c36b..d92b705e7917 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -340,10 +340,12 @@ Required properties: - compatible : "renesas,rcar_sound-<soctype>", fallbacks "renesas,rcar_sound-gen1" if generation1, and "renesas,rcar_sound-gen2" if generation2 (or RZ/G1) - "renesas,rcar_sound-gen3" if generation3 + "renesas,rcar_sound-gen3" if generation3 (or RZ/G2) Examples with soctypes are: - "renesas,rcar_sound-r8a7743" (RZ/G1M) + - "renesas,rcar_sound-r8a7744" (RZ/G1N) - "renesas,rcar_sound-r8a7745" (RZ/G1E) + - "renesas,rcar_sound-r8a774a1" (RZ/G2M) - "renesas,rcar_sound-r8a7778" (R-Car M1A) - "renesas,rcar_sound-r8a7779" (R-Car H1) - "renesas,rcar_sound-r8a7790" (R-Car H2) @@ -353,6 +355,7 @@ Required properties: - "renesas,rcar_sound-r8a7795" (R-Car H3) - "renesas,rcar_sound-r8a7796" (R-Car M3-W) - "renesas,rcar_sound-r8a77965" (R-Car M3-N) + - "renesas,rcar_sound-r8a77990" (R-Car E3) - reg : Should contain the register physical address. required register is SRU/ADG/SSI if generation1 diff --git a/Documentation/devicetree/bindings/sound/st,sta32x.txt b/Documentation/devicetree/bindings/sound/st,sta32x.txt index 255de3ae5b2f..52265fb757c5 100644 --- a/Documentation/devicetree/bindings/sound/st,sta32x.txt +++ b/Documentation/devicetree/bindings/sound/st,sta32x.txt @@ -19,6 +19,10 @@ Required properties: Optional properties: + - clocks, clock-names: Clock specifier for XTI input clock. + If specified, the clock will be enabled when the codec is probed, + and disabled when it is removed. The 'clock-names' must be set to 'xti'. + - st,output-conf: number, Selects the output configuration: 0: 2-channel (full-bridge) power, 2-channel data-out 1: 2 (half-bridge). 1 (full-bridge) on-board power @@ -39,6 +43,9 @@ Optional properties: - st,thermal-warning-recover: If present, thermal warning recovery is enabled. + - st,fault-detect-recovery: + If present, fault detect recovery is enabled. + - st,thermal-warning-adjustment: If present, thermal warning adjustment is enabled. @@ -76,6 +83,8 @@ Example: codec: sta32x@38 { compatible = "st,sta32x"; reg = <0x1c>; + clocks = <&clock>; + clock-names = "xti"; reset-gpios = <&gpio1 19 0>; power-down-gpios = <&gpio1 16 0>; st,output-conf = /bits/ 8 <0x3>; // set output to 2-channel diff --git a/Documentation/devicetree/bindings/sound/st,stm32-sai.txt b/Documentation/devicetree/bindings/sound/st,stm32-sai.txt index 3a3fc506e43a..3f4467ff0aa2 100644 --- a/Documentation/devicetree/bindings/sound/st,stm32-sai.txt +++ b/Documentation/devicetree/bindings/sound/st,stm32-sai.txt @@ -31,7 +31,11 @@ SAI subnodes required properties: - reg: Base address and size of SAI sub-block register set. - clocks: Must contain one phandle and clock specifier pair for sai_ck which feeds the internal clock generator. + If the SAI shares a master clock, with another SAI set as MCLK + clock provider, SAI provider phandle must be specified here. - clock-names: Must contain "sai_ck". + Must also contain "MCLK", if SAI shares a master clock, + with a SAI set as MCLK clock provider. - dmas: see Documentation/devicetree/bindings/dma/stm32-dma.txt - dma-names: identifier string for each DMA request line "tx": if sai sub-block is configured as playback DAI @@ -51,6 +55,9 @@ SAI subnodes Optional properties: configured according to protocol defined in related DAI link node, such as i2s, left justified, right justified, dsp and pdm protocols. Note: ac97 protocol is not supported by SAI driver + - #clock-cells: should be 0. This property must be present if the SAI device + is a master clock provider, according to clocks bindings, described in + Documentation/devicetree/bindings/clock/clock-bindings.txt. The device node should contain one 'port' child node with one child 'endpoint' node, according to the bindings defined in Documentation/devicetree/bindings/ diff --git a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt index b9d50d6cdef3..61e71c1729e0 100644 --- a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt +++ b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt @@ -10,6 +10,7 @@ Required properties: - "allwinner,sun6i-a31-i2s" - "allwinner,sun8i-a83t-i2s" - "allwinner,sun8i-h3-i2s" + - "allwinner,sun50i-a64-codec-i2s" - reg: physical base address of the controller and length of memory mapped region. - interrupts: should contain the I2S interrupt. @@ -26,6 +27,7 @@ Required properties for the following compatibles: - "allwinner,sun6i-a31-i2s" - "allwinner,sun8i-a83t-i2s" - "allwinner,sun8i-h3-i2s" + - "allwinner,sun50i-a64-codec-i2s" - resets: phandle to the reset line for this codec Example: diff --git a/Documentation/devicetree/bindings/sound/sun50i-codec-analog.txt b/Documentation/devicetree/bindings/sound/sun50i-codec-analog.txt new file mode 100644 index 000000000000..4f8ad0e04d20 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sun50i-codec-analog.txt @@ -0,0 +1,12 @@ +* Allwinner A64 Codec Analog Controls + +Required properties: +- compatible: must be one of the following compatibles: + - "allwinner,sun50i-a64-codec-analog" +- reg: must contain the registers location and length + +Example: + codec_analog: codec-analog@1f015c0 { + compatible = "allwinner,sun50i-a64-codec-analog"; + reg = <0x01f015c0 0x4>; + }; diff --git a/Documentation/devicetree/bindings/sound/ts3a227e.txt b/Documentation/devicetree/bindings/sound/ts3a227e.txt index 3ed8359144d3..21ab45bc7e8f 100644 --- a/Documentation/devicetree/bindings/sound/ts3a227e.txt +++ b/Documentation/devicetree/bindings/sound/ts3a227e.txt @@ -14,7 +14,7 @@ Required properties: Optional properies: - ti,micbias: Intended MICBIAS voltage (datasheet section 9.6.7). - Select 0/1/2/3/4/5/6/7 to specify MACBIAS voltage + Select 0/1/2/3/4/5/6/7 to specify MICBIAS voltage 2.1V/2.2V/2.3V/2.4V/2.5V/2.6V/2.7V/2.8V Default value is "1" (2.2V). diff --git a/Documentation/devicetree/bindings/sound/wm8782.txt b/Documentation/devicetree/bindings/sound/wm8782.txt new file mode 100644 index 000000000000..256cdec6ec4d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8782.txt @@ -0,0 +1,17 @@ +WM8782 stereo ADC + +This device does not have any control interface or reset pins. + +Required properties: + + - compatible : "wlf,wm8782" + - Vdda-supply : phandle to a regulator for the analog power supply (2.7V - 5.5V) + - Vdd-supply : phandle to a regulator for the digital power supply (2.7V - 3.6V) + +Example: + +wm8782: stereo-adc { + compatible = "wlf,wm8782"; + Vdda-supply = <&vdda_supply>; + Vdd-supply = <&vdd_supply>; +}; diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt new file mode 100644 index 000000000000..790311a42bf1 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt @@ -0,0 +1,39 @@ +GENI based Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI) + +The QUP v3 core is a GENI based AHB slave that provides a common data path +(an output FIFO and an input FIFO) for serial peripheral interface (SPI) +mini-core. + +SPI in master mode supports up to 50MHz, up to four chip selects, programmable +data path from 4 bits to 32 bits and numerous protocol variants. + +Required properties: +- compatible: Must contain "qcom,geni-spi". +- reg: Must contain SPI register location and length. +- interrupts: Must contain SPI controller interrupts. +- clock-names: Must contain "se". +- clocks: Serial engine core clock needed by the device. +- #address-cells: Must be <1> to define a chip select address on + the SPI bus. +- #size-cells: Must be <0>. + +SPI Controller nodes must be child of GENI based Qualcomm Universal +Peripharal. Please refer GENI based QUP wrapper controller node bindings +described in Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt. + +SPI slave nodes must be children of the SPI master node and conform to SPI bus +binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt. + +Example: + spi0: spi@a84000 { + compatible = "qcom,geni-spi"; + reg = <0xa84000 0x4000>; + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "se"; + clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qup_1_spi_2_active>; + pinctrl-1 = <&qup_1_spi_2_sleep>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt new file mode 100644 index 000000000000..1d64b61f5171 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt @@ -0,0 +1,36 @@ +Qualcomm Quad Serial Peripheral Interface (QSPI) + +The QSPI controller allows SPI protocol communication in single, dual, or quad +wire transmission modes for read/write access to slaves such as NOR flash. + +Required properties: +- compatible: An SoC specific identifier followed by "qcom,qspi-v1", such as + "qcom,sdm845-qspi", "qcom,qspi-v1" +- reg: Should contain the base register location and length. +- interrupts: Interrupt number used by the controller. +- clocks: Should contain the core and AHB clock. +- clock-names: Should be "core" for core clock and "iface" for AHB clock. + +SPI slave nodes must be children of the SPI master node and can contain +properties described in Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + + qspi: spi@88df000 { + compatible = "qcom,sdm845-qspi", "qcom,qspi-v1"; + reg = <0x88df000 0x600>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "iface", "core"; + clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>, + <&gcc GCC_QSPI_CORE_CLK>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index bfbc2035fb6b..4b836ad17b19 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -2,7 +2,9 @@ Renesas MSIOF spi controller Required properties: - compatible : "renesas,msiof-r8a7743" (RZ/G1M) + "renesas,msiof-r8a7744" (RZ/G1N) "renesas,msiof-r8a7745" (RZ/G1E) + "renesas,msiof-r8a774a1" (RZ/G2M) "renesas,msiof-r8a7790" (R-Car H2) "renesas,msiof-r8a7791" (R-Car M2-W) "renesas,msiof-r8a7792" (R-Car V2H) @@ -11,10 +13,14 @@ Required properties: "renesas,msiof-r8a7795" (R-Car H3) "renesas,msiof-r8a7796" (R-Car M3-W) "renesas,msiof-r8a77965" (R-Car M3-N) + "renesas,msiof-r8a77970" (R-Car V3M) + "renesas,msiof-r8a77980" (R-Car V3H) + "renesas,msiof-r8a77990" (R-Car E3) + "renesas,msiof-r8a77995" (R-Car D3) "renesas,msiof-sh73a0" (SH-Mobile AG5) "renesas,sh-mobile-msiof" (generic SH-Mobile compatibile device) "renesas,rcar-gen2-msiof" (generic R-Car Gen2 and RZ/G1 compatible device) - "renesas,rcar-gen3-msiof" (generic R-Car Gen3 compatible device) + "renesas,rcar-gen3-msiof" (generic R-Car Gen3 and RZ/G2 compatible device) "renesas,sh-msiof" (deprecated) When compatible with the generic version, nodes diff --git a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt index 642d3fb1ef85..2864bc6b659c 100644 --- a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt +++ b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt @@ -2,7 +2,7 @@ Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface. Required properties: - compatible : "snps,dw-apb-ssi" or "mscc,<soc>-spi", where soc is "ocelot" or - "jaguar2" + "jaguar2", or "amazon,alpine-dw-apb-ssi" - reg : The register base for the controller. For "mscc,<soc>-spi", a second register set is required (named ICPU_CFG:SPI_MST) - interrupts : One interrupt, used by the controller. diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt index 4af132606b37..8d178a4503cf 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt @@ -3,6 +3,7 @@ Required properties: - compatible : - "fsl,imx7ulp-spi" for LPSPI compatible with the one integrated on i.MX7ULP soc + - "fsl,imx8qxp-spi" for LPSPI compatible with the one integrated on i.MX8QXP soc - reg : address and length of the lpspi master registers - interrupts : lpspi interrupt - clocks : lpspi clock specifier diff --git a/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt b/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt new file mode 100644 index 000000000000..0335a9bd2e8a --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt @@ -0,0 +1,24 @@ +PXA2xx SSP SPI Controller + +Required properties: +- compatible: Must be "marvell,mmp2-ssp". +- reg: Offset and length of the device's register set. +- interrupts: Should be the interrupt number. +- clocks: Should contain a single entry describing the clock input. +- #address-cells: Number of cells required to define a chip select address. +- #size-cells: Should be zero. + +Optional properties: +- cs-gpios: list of GPIO chip selects. See the SPI bus bindings, + Documentation/devicetree/bindings/spi/spi-bus.txt + +Child nodes represent devices on the SPI bus + See ../spi/spi-bus.txt + +Example: + ssp1: spi@d4035000 { + compatible = "marvell,mmp2-ssp"; + reg = <0xd4035000 0x1000>; + clocks = <&soc_clocks MMP2_CLK_SSP0>; + interrupts = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-rspi.txt b/Documentation/devicetree/bindings/spi/spi-rspi.txt index 96fd58548f69..fc97ad64fbf2 100644 --- a/Documentation/devicetree/bindings/spi/spi-rspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-rspi.txt @@ -3,7 +3,7 @@ Device tree configuration for Renesas RSPI/QSPI driver Required properties: - compatible : For Renesas Serial Peripheral Interface on legacy SH: "renesas,rspi-<soctype>", "renesas,rspi" as fallback. - For Renesas Serial Peripheral Interface on RZ/A1H: + For Renesas Serial Peripheral Interface on RZ/A: "renesas,rspi-<soctype>", "renesas,rspi-rz" as fallback. For Quad Serial Peripheral Interface on R-Car Gen2 and RZ/G1 devices: @@ -11,7 +11,9 @@ Required properties: Examples with soctypes are: - "renesas,rspi-sh7757" (SH) - "renesas,rspi-r7s72100" (RZ/A1H) + - "renesas,rspi-r7s9210" (RZ/A2) - "renesas,qspi-r8a7743" (RZ/G1M) + - "renesas,qspi-r8a7744" (RZ/G1N) - "renesas,qspi-r8a7745" (RZ/G1E) - "renesas,qspi-r8a7790" (R-Car H2) - "renesas,qspi-r8a7791" (R-Car M2-W) diff --git a/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt b/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt new file mode 100644 index 000000000000..c37e5a179b21 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt @@ -0,0 +1,32 @@ +Binding for MTK SPI Slave controller + +Required properties: +- compatible: should be one of the following. + - mediatek,mt2712-spi-slave: for mt2712 platforms +- reg: Address and length of the register set for the device. +- interrupts: Should contain spi interrupt. +- clocks: phandles to input clocks. + It's clock gate, and should be <&infracfg CLK_INFRA_AO_SPI1>. +- clock-names: should be "spi" for the clock gate. + +Optional properties: +- assigned-clocks: it's mux clock, should be <&topckgen CLK_TOP_SPISLV_SEL>. +- assigned-clock-parents: parent of mux clock. + It's PLL, and should be one of the following. + - <&topckgen CLK_TOP_UNIVPLL1_D2>: specify parent clock 312MHZ. + It's the default one. + - <&topckgen CLK_TOP_UNIVPLL1_D4>: specify parent clock 156MHZ. + - <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ. + - <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ. + +Example: +- SoC Specific Portion: +spis1: spi@10013000 { + compatible = "mediatek,mt2712-spi-slave"; + reg = <0 0x10013000 0 0x100>; + interrupts = <GIC_SPI 283 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_AO_SPI1>; + clock-names = "spi"; + assigned-clocks = <&topckgen CLK_TOP_SPISLV_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL1_D2>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-sprd.txt b/Documentation/devicetree/bindings/spi/spi-sprd.txt new file mode 100644 index 000000000000..bad211a19da4 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sprd.txt @@ -0,0 +1,26 @@ +Spreadtrum SPI Controller + +Required properties: +- compatible: Should be "sprd,sc9860-spi". +- reg: Offset and length of SPI controller register space. +- interrupts: Should contain SPI interrupt. +- clock-names: Should contain following entries: + "spi" for SPI clock, + "source" for SPI source (parent) clock, + "enable" for SPI module enable clock. +- clocks: List of clock input name strings sorted in the same order + as the clock-names property. +- #address-cells: The number of cells required to define a chip select + address on the SPI bus. Should be set to 1. +- #size-cells: Should be set to 0. + +Example: +spi0: spi@70a00000{ + compatible = "sprd,sc9860-spi"; + reg = <0 0x70a00000 0 0x1000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "spi", "source","enable"; + clocks = <&clk_spi0>, <&ext_26m>, <&clk_ap_apb_gates 5>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt new file mode 100644 index 000000000000..adeeb63e84b9 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt @@ -0,0 +1,44 @@ +* STMicroelectronics Quad Serial Peripheral Interface(QSPI) + +Required properties: +- compatible: should be "st,stm32f469-qspi" +- reg: the first contains the register location and length. + the second contains the memory mapping address and length +- reg-names: should contain the reg names "qspi" "qspi_mm" +- interrupts: should contain the interrupt for the device +- clocks: the phandle of the clock needed by the QSPI controller +- A pinctrl must be defined to set pins in mode of operation for QSPI transfer + +Optional properties: +- resets: must contain the phandle to the reset controller. + +A spi flash (NOR/NAND) must be a child of spi node and could have some +properties. Also see jedec,spi-nor.txt. + +Required properties: +- reg: chip-Select number (QSPI controller may connect 2 flashes) +- spi-max-frequency: max frequency of spi bus + +Optional property: +- spi-rx-bus-width: see ./spi-bus.txt for the description + +Example: + +qspi: spi@a0001000 { + compatible = "st,stm32f469-qspi"; + reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>; + reg-names = "qspi", "qspi_mm"; + interrupts = <91>; + resets = <&rcc STM32F4_AHB3_RESET(QSPI)>; + clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi0>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/timer/renesas,cmt.txt b/Documentation/devicetree/bindings/timer/renesas,cmt.txt index b40add2d9bb4..49948fcc0631 100644 --- a/Documentation/devicetree/bindings/timer/renesas,cmt.txt +++ b/Documentation/devicetree/bindings/timer/renesas,cmt.txt @@ -34,6 +34,10 @@ Required Properties: - "renesas,r8a7793-cmt1" for the 48-bit CMT1 device included in r8a7793. - "renesas,r8a7794-cmt0" for the 32-bit CMT0 device included in r8a7794. - "renesas,r8a7794-cmt1" for the 48-bit CMT1 device included in r8a7794. + - "renesas,r8a77970-cmt0" for the 32-bit CMT0 device included in r8a77970. + - "renesas,r8a77970-cmt1" for the 48-bit CMT1 device included in r8a77970. + - "renesas,r8a77980-cmt0" for the 32-bit CMT0 device included in r8a77980. + - "renesas,r8a77980-cmt1" for the 48-bit CMT1 device included in r8a77980. - "renesas,rcar-gen2-cmt0" for 32-bit CMT0 devices included in R-Car Gen2 and RZ/G1. @@ -41,6 +45,9 @@ Required Properties: and RZ/G1. These are fallbacks for r8a73a4, R-Car Gen2 and RZ/G1 entries listed above. + - "renesas,rcar-gen3-cmt0" for 32-bit CMT0 devices included in R-Car Gen3. + - "renesas,rcar-gen3-cmt1" for 48-bit CMT1 devices included in R-Car Gen3. + These are fallbacks for R-Car Gen3 entries listed above. - reg: base address and length of the registers block for the timer module. - interrupts: interrupt-specifier for the timer, one per channel. diff --git a/Documentation/devicetree/bindings/trivial-devices.txt b/Documentation/devicetree/bindings/trivial-devices.txt index 763a2808a95c..69c934aec13b 100644 --- a/Documentation/devicetree/bindings/trivial-devices.txt +++ b/Documentation/devicetree/bindings/trivial-devices.txt @@ -35,7 +35,6 @@ at,24c08 i2c serial eeprom (24cxx) atmel,at97sc3204t i2c trusted platform module (TPM) capella,cm32181 CM32181: Ambient Light Sensor capella,cm3232 CM3232: Ambient Light Sensor -cirrus,cs42l51 Cirrus Logic CS42L51 audio codec dallas,ds1374 I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output dallas,ds1631 High-Precision Digital Thermometer dallas,ds1672 Dallas DS1672 Real-time Clock diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 2e9318151df7..529e51879fb2 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -80,6 +80,8 @@ Optional properties: controller. It's expected that a mux state of 0 indicates device mode and a mux state of 1 indicates host mode. - mux-control-names: Shall be "usb_switch" if mux-controls is specified. +- pinctrl-names: Names for optional pin modes in "default", "host", "device" +- pinctrl-n: alternate pin modes i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 3e4c38b806ac..636630fb92d7 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -19,6 +19,7 @@ Exception for clocks: "cavium,octeon-7130-usb-uctl" "qcom,dwc3" "samsung,exynos5250-dwusb3" + "samsung,exynos5433-dwusb3" "samsung,exynos7-dwusb3" "sprd,sc9860-dwc3" "st,stih407-dwc3" diff --git a/Documentation/devicetree/bindings/usb/ehci-mv.txt b/Documentation/devicetree/bindings/usb/ehci-mv.txt new file mode 100644 index 000000000000..335589895763 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ehci-mv.txt @@ -0,0 +1,23 @@ +* Marvell PXA/MMP EHCI controller. + +Required properties: + +- compatible: must be "marvell,pxau2o-ehci" +- reg: physical base addresses of the controller and length of memory mapped region +- interrupts: one EHCI controller interrupt should be described here +- clocks: phandle list of usb clocks +- clock-names: should be "USBCLK" +- phys: phandle for the PHY device +- phy-names: should be "usb" + +Example: + + ehci0: usb-ehci@d4208000 { + compatible = "marvell,pxau2o-ehci"; + reg = <0xd4208000 0x200>; + interrupts = <44>; + clocks = <&soc_clocks MMP2_CLK_USB>; + clock-names = "USBCLK"; + phys = <&usb_otg_phy>; + phy-names = "usb"; + }; diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt index c97374315049..b7111f43fa59 100644 --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt @@ -83,6 +83,8 @@ Required properties: - compatible: should be one of the following - "samsung,exynos5250-dwusb3": for USB 3.0 DWC3 controller on Exynos5250/5420. + "samsung,exynos5433-dwusb3": for USB 3.0 DWC3 controller on + Exynos5433. "samsung,exynos7-dwusb3": for USB 3.0 DWC3 controller on Exynos7. - #address-cells, #size-cells : should be '1' if the device has sub-nodes with 'reg' property. diff --git a/Documentation/devicetree/bindings/usb/faraday,fotg210.txt b/Documentation/devicetree/bindings/usb/faraday,fotg210.txt new file mode 100644 index 000000000000..06a2286e2054 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/faraday,fotg210.txt @@ -0,0 +1,35 @@ +Faraday FOTG Host controller + +This OTG-capable USB host controller is found in Cortina Systems +Gemini and other SoC products. + +Required properties: +- compatible: should be one of: + "faraday,fotg210" + "cortina,gemini-usb", "faraday,fotg210" +- reg: should contain one register range i.e. start and length +- interrupts: description of the interrupt line + +Optional properties: +- clocks: should contain the IP block clock +- clock-names: should be "PCLK" for the IP block clock + +Required properties for "cortina,gemini-usb" compatible: +- syscon: a phandle to the system controller to access PHY registers + +Optional properties for "cortina,gemini-usb" compatible: +- cortina,gemini-mini-b: boolean property that indicates that a Mini-B + OTG connector is in use +- wakeup-source: see power/wakeup-source.txt + +Example for Gemini: + +usb@68000000 { + compatible = "cortina,gemini-usb", "faraday,fotg210"; + reg = <0x68000000 0x1000>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cc 12>; + clock-names = "PCLK"; + syscon = <&syscon>; + wakeup-source; +}; diff --git a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt index 6087dc7f209e..a5d011d2efc8 100644 --- a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt +++ b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt @@ -5,10 +5,19 @@ Required properties : - reg : I2C slave address - interrupts : Interrupt specifier -Optional properties : -- fcs,operating-sink-microwatt : - Minimum amount of power accepted from a sink - when negotiating +Required sub-node: +- connector : The "usb-c-connector" attached to the FUSB302 IC. The bindings + of the connector node are specified in: + + Documentation/devicetree/bindings/connector/usb-connector.txt + +Deprecated properties : +- fcs,max-sink-microvolt : Maximum sink voltage accepted by port controller +- fcs,max-sink-microamp : Maximum sink current accepted by port controller +- fcs,max-sink-microwatt : Maximum sink power accepted by port controller +- fcs,operating-sink-microwatt : Minimum amount of power accepted from a sink + when negotiating + Example: @@ -17,7 +26,16 @@ fusb302: typec-portc@54 { reg = <0x54>; interrupt-parent = <&nmi_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - fcs,max-sink-microvolt = <12000000>; - fcs,max-sink-microamp = <3000000>; - fcs,max-sink-microwatt = <36000000>; + + usb_con: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + power-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM) + PDO_VAR(3000, 12000, 3000) + PDO_PPS_APDO(3000, 11000, 3000)>; + op-sink-microwatt = <10000000>; + }; }; diff --git a/Documentation/devicetree/bindings/usb/renesas_usb3.txt b/Documentation/devicetree/bindings/usb/renesas_usb3.txt index 2c071bb5801e..d366555166d0 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usb3.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usb3.txt @@ -2,11 +2,13 @@ Renesas Electronics USB3.0 Peripheral driver Required properties: - compatible: Must contain one of the following: + - "renesas,r8a774a1-usb3-peri" - "renesas,r8a7795-usb3-peri" - "renesas,r8a7796-usb3-peri" - "renesas,r8a77965-usb3-peri" - - "renesas,rcar-gen3-usb3-peri" for a generic R-Car Gen3 compatible - device + - "renesas,r8a77990-usb3-peri" + - "renesas,rcar-gen3-usb3-peri" for a generic R-Car Gen3 or RZ/G2 + compatible device When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index 43960faf5a88..90719f501852 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -4,7 +4,9 @@ Required properties: - compatible: Must contain one or more of the following: - "renesas,usbhs-r8a7743" for r8a7743 (RZ/G1M) compatible device + - "renesas,usbhs-r8a7744" for r8a7744 (RZ/G1N) compatible device - "renesas,usbhs-r8a7745" for r8a7745 (RZ/G1E) compatible device + - "renesas,usbhs-r8a774a1" for r8a774a1 (RZ/G2M) compatible device - "renesas,usbhs-r8a7790" for r8a7790 (R-Car H2) compatible device - "renesas,usbhs-r8a7791" for r8a7791 (R-Car M2-W) compatible device - "renesas,usbhs-r8a7792" for r8a7792 (R-Car V2H) compatible device @@ -13,10 +15,11 @@ Required properties: - "renesas,usbhs-r8a7795" for r8a7795 (R-Car H3) compatible device - "renesas,usbhs-r8a7796" for r8a7796 (R-Car M3-W) compatible device - "renesas,usbhs-r8a77965" for r8a77965 (R-Car M3-N) compatible device + - "renesas,usbhs-r8a77990" for r8a77990 (R-Car E3) compatible device - "renesas,usbhs-r8a77995" for r8a77995 (R-Car D3) compatible device - "renesas,usbhs-r7s72100" for r7s72100 (RZ/A1) compatible device - "renesas,rcar-gen2-usbhs" for R-Car Gen2 or RZ/G1 compatible devices - - "renesas,rcar-gen3-usbhs" for R-Car Gen3 compatible device + - "renesas,rcar-gen3-usbhs" for R-Car Gen3 or RZ/G2 compatible devices - "renesas,rza1-usbhs" for RZ/A1 compatible device When compatible with the generic version, nodes must list the @@ -25,7 +28,11 @@ Required properties: - reg: Base address and length of the register for the USBHS - interrupts: Interrupt specifier for the USBHS - - clocks: A list of phandle + clock specifier pairs + - clocks: A list of phandle + clock specifier pairs. + - In case of "renesas,rcar-gen3-usbhs", two clocks are required. + First clock should be peripheral and second one should be host. + - In case of except above, one clock is required. First clock + should be peripheral. Optional properties: - renesas,buswait: Integer to use BUSWAIT register diff --git a/Documentation/devicetree/bindings/usb/usb-ehci.txt b/Documentation/devicetree/bindings/usb/usb-ehci.txt index 0f1b75386207..406252d14c6b 100644 --- a/Documentation/devicetree/bindings/usb/usb-ehci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ehci.txt @@ -15,7 +15,11 @@ Optional properties: - needs-reset-on-resume : boolean, set this to force EHCI reset after resume - has-transaction-translator : boolean, set this if EHCI have a Transaction Translator built into the root hub. - - clocks : a list of phandle + clock specifier pairs + - clocks : a list of phandle + clock specifier pairs. In case of Renesas + R-Car Gen3 SoCs: + - if a host only channel: first clock should be host. + - if a USB DRD channel: first clock should be host and second one + should be peripheral. - phys : see usb-hcd.txt in the current directory - resets : phandle + reset specifier pair diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt index a8d2103d1f3d..aaaa5255c972 100644 --- a/Documentation/devicetree/bindings/usb/usb-ohci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -12,7 +12,11 @@ Optional properties: - no-big-frame-no : boolean, set if frame_no lives in bits [15:0] of HCCA - remote-wakeup-connected: remote wakeup is wired on the platform - num-ports : u32, to override the detected port count -- clocks : a list of phandle + clock specifier pairs +- clocks : a list of phandle + clock specifier pairs. In case of Renesas + R-Car Gen3 SoCs: + - if a host only channel: first clock should be host. + - if a USB DRD channel: first clock should be host and second one + should be peripheral. - phys : see usb-hcd.txt in the current directory - resets : a list of phandle + reset specifier pairs diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index ac4cd0d6195a..fea8b1545751 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -8,6 +8,8 @@ Required properties: - "marvell,armada-375-xhci" for Armada 375 SoCs - "marvell,armada-380-xhci" for Armada 38x SoCs - "renesas,xhci-r8a7743" for r8a7743 SoC + - "renesas,xhci-r8a7744" for r8a7744 SoC + - "renesas,xhci-r8a774a1" for r8a774a1 SoC - "renesas,xhci-r8a7790" for r8a7790 SoC - "renesas,xhci-r8a7791" for r8a7791 SoC - "renesas,xhci-r8a7793" for r8a7793 SoC @@ -17,7 +19,8 @@ Required properties: - "renesas,xhci-r8a77990" for r8a77990 SoC - "renesas,rcar-gen2-xhci" for a generic R-Car Gen2 or RZ/G1 compatible device - - "renesas,rcar-gen3-xhci" for a generic R-Car Gen3 compatible device + - "renesas,rcar-gen3-xhci" for a generic R-Car Gen3 or RZ/G2 compatible + device - "xhci-platform" (deprecated) When compatible with the generic version, nodes must list the diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 2c3fc512e746..f26bf667e530 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -235,6 +235,7 @@ micrel Micrel Inc. microchip Microchip Technology Inc. microcrystal Micro Crystal AG micron Micron Technology Inc. +mikroe MikroElektronika d.o.o. minix MINIX Technology Ltd. miramems MiraMEMS Sensing Technology Co., Ltd. mitsubishi Mitsubishi Electric Corporation |
