3 files changed, 70 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/nfc/pn544.txt b/Documentation/devicetree/bindings/net/nfc/pn544.txt
new file mode 100644
index 000000000000..dab69f36167c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/pn544.txt
@@ -0,0 +1,35 @@
+* NXP Semiconductors PN544 NFC Controller
+
+Required properties:
+- compatible: Should be "nxp,pn544-i2c".
+- clock-frequency: I²C work frequency.
+- reg: address on the bus
+- interrupt-parent: phandle for the interrupt gpio controller
+- interrupts: GPIO interrupt to which the chip is connected
+- enable-gpios: Output GPIO pin used for enabling/disabling the PN544
+- firmware-gpios: Output GPIO pin used to enter firmware download mode
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+
+Example (for ARM-based BeagleBone with PN544 on I2C2):
+
+&i2c2 {
+
+	status = "okay";
+
+	pn544: pn544@28 {
+
+		compatible = "nxp,pn544-i2c";
+
+		reg = <0x28>;
+		clock-frequency = <400000>;
+
+		interrupt-parent = <&gpio1>;
+		interrupts = <17 GPIO_ACTIVE_HIGH>;
+
+		enable-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+		firmware-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfca.txt b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt
new file mode 100644
index 000000000000..4724fe669172
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt
@@ -0,0 +1,33 @@
+* STMicroelectronics SAS. ST21NFCA NFC Controller
+
+Required properties:
+- compatible: Should be "st,st21nfca-i2c".
+- clock-frequency: I²C work frequency.
+- reg: address on the bus
+- interrupt-parent: phandle for the interrupt gpio controller
+- interrupts: GPIO interrupt to which the chip is connected
+- enable-gpios: Output GPIO pin used for enabling/disabling the ST21NFCA
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+
+Example (for ARM-based BeagleBoard xM with ST21NFCA on I2C2):
+
+&i2c2 {
+
+	status = "okay";
+
+	st21nfca: st21nfca@1 {
+
+		compatible = "st,st21nfca_i2c";
+
+		reg = <0x01>;
+		clock-frequency = <400000>;
+
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+
+		enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
index 8dd3ef7bc56b..1e436133685f 100644
--- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
+++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
@@ -12,6 +12,7 @@ Required properties:
 Optional SoC Specific Properties:
 - pinctrl-names: Contains only one value - "default".
 - pintctrl-0: Specifies the pin control groups used for this controller.
+- autosuspend-delay: Specify autosuspend delay in milliseconds.
 
 Example (for ARM-based BeagleBone with TRF7970A on SPI1):
 
@@ -29,6 +30,7 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
 		ti,enable-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>,
 				  <&gpio2 5 GPIO_ACTIVE_LOW>;
 		vin-supply = <&ldo3_reg>;
+		autosuspend-delay = <30000>;
 		status = "okay";
 	};
 };