diff options
Diffstat (limited to 'Documentation/devicetree')
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/as3722.txt | 194 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/s2mps11.txt | 13 |
2 files changed, 201 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/mfd/as3722.txt b/Documentation/devicetree/bindings/mfd/as3722.txt new file mode 100644 index 000000000000..fc2191ecfd6b --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/as3722.txt @@ -0,0 +1,194 @@ +* ams AS3722 Power management IC. + +Required properties: +------------------- +- compatible: Must be "ams,as3722". +- reg: I2C device address. +- interrupt-controller: AS3722 has internal interrupt controller which takes the + interrupt request from internal sub-blocks like RTC, regulators, GPIOs as well + as external input. +- #interrupt-cells: Should be set to 2 for IRQ number and flags. + The first cell is the IRQ number. IRQ numbers for different interrupt source + of AS3722 are defined at dt-bindings/mfd/as3722.h + The second cell is the flags, encoded as the trigger masks from binding document + interrupts.txt, using dt-bindings/irq. + +Optional submodule and their properties: +======================================= + +Pinmux and GPIO: +=============== +Device has 8 GPIO pins which can be configured as GPIO as well as the special IO +functions. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Following are properties which is needed if GPIO and pinmux functionality +is required: + Required properties: + ------------------- + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Number of GPIO cells. Refer to binding document + gpio/gpio.txt + + Optional properties: + -------------------- + Following properties are require if pin control setting is required + at boot. + - pinctrl-names: A pinctrl state named "default" be defined, using the + bindings in pinctrl/pinctrl-binding.txt. + - pinctrl[0...n]: Properties to contain the phandle that refer to + different nodes of pin control settings. These nodes represents + the pin control setting of state 0 to state n. Each of these + nodes contains different subnodes to represents some desired + configuration for a list of pins. This configuration can + include the mux function to select on those pin(s), and + various pin configuration parameters, such as pull-up, + open drain. + + Each subnode have following properties: + Required properties: + - pins: List of pins. Valid values of pins properties are: + gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, + gpio6, gpio7 + + Optional properties: + function, bias-disable, bias-pull-up, bias-pull-down, + bias-high-impedance, drive-open-drain. + + Valid values for function properties are: + gpio, interrupt-out, gpio-in-interrupt, + vsup-vbat-low-undebounce-out, + vsup-vbat-low-debounce-out, + voltage-in-standby, oc-pg-sd0, oc-pg-sd6, + powergood-out, pwm-in, pwm-out, clk32k-out, + watchdog-in, soft-reset-in + +Regulators: +=========== +Device has multiple DCDC and LDOs. The node "regulators" is require if regulator +functionality is needed. + +Following are properties of regulator subnode. + + Optional properties: + ------------------- + The input supply of regulators are the optional properties on the + regulator node. The input supply of these regulators are provided + through following properties: + vsup-sd2-supply: Input supply for SD2. + vsup-sd3-supply: Input supply for SD3. + vsup-sd4-supply: Input supply for SD4. + vsup-sd5-supply: Input supply for SD5. + vin-ldo0-supply: Input supply for LDO0. + vin-ldo1-6-supply: Input supply for LDO1 and LDO6. + vin-ldo2-5-7-supply: Input supply for LDO2, LDO5 and LDO7. + vin-ldo3-4-supply: Input supply for LDO3 and LDO4. + vin-ldo9-10-supply: Input supply for LDO9 and LDO10. + vin-ldo11-supply: Input supply for LDO11. + + Optional sub nodes for regulators: + --------------------------------- + The subnodes name is the name of regulator and it must be one of: + sd[0-6], ldo[0-7], ldo[9-11] + + Each sub-node should contain the constraints and initialization + information for that regulator. See regulator.txt for a description + of standard properties for these sub-nodes. + Additional optional custom properties are listed below. + ams,ext-control: External control of the rail. The option of + this properties will tell which external input is + controlling this rail. Valid values are 0, 1, 2 ad 3. + 0: There is no external control of this rail. + 1: Rail is controlled by ENABLE1 input pin. + 2: Rail is controlled by ENABLE2 input pin. + 3: Rail is controlled by ENABLE3 input pin. + Missing this property on DT will be assume as no + external control. The external control pin macros + are defined @dt-bindings/mfd/as3722.h + + ams,enable-tracking: Enable tracking with SD1, only supported + by LDO3. + +Example: +-------- +#include <dt-bindings/mfd/as3722.h> +... +ams3722 { + compatible = "ams,as3722"; + reg = <0x48>; + + interrupt-parent = <&intc>; + interrupt-controller; + #interrupt-cells = <2>; + + gpio-controller; + #gpio-cells = <2>; + + pinctrl-names = "default"; + pinctrl-0 = <&as3722_default>; + + as3722_default: pinmux { + gpio0 { + pins = "gpio0"; + function = "gpio"; + bias-pull-down; + }; + + gpio1_2_4_7 { + pins = "gpio1", "gpio2", "gpio4", "gpio7"; + function = "gpio"; + bias-pull-up; + }; + + gpio5 { + pins = "gpio5"; + function = "clk32k_out"; + }; + } + + regulators { + vsup-sd2-supply = <...>; + ... + + sd0 { + regulator-name = "vdd_cpu"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + ams,ext-control = <2>; + }; + + sd1 { + regulator-name = "vdd_core"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + ams,ext-control = <1>; + }; + + sd2 { + regulator-name = "vddio_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + sd4 { + regulator-name = "avdd-hdmi-pex"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + }; + + sd5 { + regulator-name = "vdd-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + .... + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index c9332c626021..78a840d7510d 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -1,10 +1,10 @@ * Samsung S2MPS11 Voltage and Current Regulator -The Samsung S2MP211 is a multi-function device which includes voltage and +The Samsung S2MPS11 is a multi-function device which includes voltage and current regulators, RTC, charger controller and other sub-blocks. It is -interfaced to the host controller using a I2C interface. Each sub-block is -addressed by the host system using different I2C slave address. +interfaced to the host controller using an I2C interface. Each sub-block is +addressed by the host system using different I2C slave addresses. Required properties: - compatible: Should be "samsung,s2mps11-pmic". @@ -43,7 +43,8 @@ sub-node should be of the format as listed below. BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explictly regulator-ramp-delay = <0> can be used for them to disable ramp delay. - In absence of regulator-ramp-delay property, default ramp delay will be used. + In the absence of the regulator-ramp-delay property, the default ramp + delay will be used. NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set for a particular group of BUCKs. So provide same regulator-ramp-delay<value>. @@ -58,10 +59,10 @@ supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number as per the datasheet of s2mps11. - LDOn - - valid values for n are 1 to 28 + - valid values for n are 1 to 38 - Example: LDO0, LD01, LDO28 - BUCKn - - valid values for n are 1 to 9. + - valid values for n are 1 to 10. - Example: BUCK1, BUCK2, BUCK9 Example: |
