diff options
Diffstat (limited to 'Documentation/devicetree')
27 files changed, 1053 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt new file mode 100644 index 000000000000..e37241f1fdd8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/davinci/nand.txt @@ -0,0 +1,51 @@ +* Texas Instruments Davinci NAND + +This file provides information, what the device node for the +davinci nand interface contain. + +Required properties: +- compatible: "ti,davinci-nand"; +- reg : contain 2 offset/length values: + - offset and length for the access window + - offset and length for accessing the aemif control registers +- ti,davinci-chipselect: Indicates on the davinci_nand driver which + chipselect is used for accessing the nand. + +Recommended properties : +- ti,davinci-mask-ale: mask for ale +- ti,davinci-mask-cle: mask for cle +- ti,davinci-mask-chipsel: mask for chipselect +- ti,davinci-ecc-mode: ECC mode valid values for davinci driver: + - "none" + - "soft" + - "hw" +- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4. +- ti,davinci-nand-buswidth: buswidth 8 or 16 +- ti,davinci-nand-use-bbt: use flash based bad block table support. + +Example (enbw_cmc board): +aemif@60000000 { + compatible = "ti,davinci-aemif"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0x68000000 0x80000>; + ranges = <2 0 0x60000000 0x02000000 + 3 0 0x62000000 0x02000000 + 4 0 0x64000000 0x02000000 + 5 0 0x66000000 0x02000000 + 6 0 0x68000000 0x02000000>; + nand@3,0 { + compatible = "ti,davinci-nand"; + reg = <3 0x0 0x807ff + 6 0x0 0x8000>; + #address-cells = <1>; + #size-cells = <1>; + ti,davinci-chipselect = <1>; + ti,davinci-mask-ale = <0>; + ti,davinci-mask-cle = <0>; + ti,davinci-mask-chipsel = <0>; + ti,davinci-ecc-mode = "hw"; + ti,davinci-ecc-bits = <4>; + ti,davinci-nand-use-bbt; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt new file mode 100644 index 000000000000..0a85c70cd30a --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt @@ -0,0 +1,68 @@ +* Atmel High Speed MultiMedia Card Interface + +This controller on atmel products provides an interface for MMC, SD and SDIO +types of memory cards. + +This file documents differences between the core properties described +by mmc.txt and the properties used by the atmel-mci driver. + +1) MCI node + +Required properties: +- compatible: should be "atmel,hsmci" +- #address-cells: should be one. The cell is the slot id. +- #size-cells: should be zero. +- at least one slot node + +The node contains child nodes for each slot that the platform uses + +Example MCI node: + +mmc0: mmc@f0008000 { + compatible = "atmel,hsmci"; + reg = <0xf0008000 0x600>; + interrupts = <12 4>; + #address-cells = <1>; + #size-cells = <0>; + + [ child node definitions...] +}; + +2) slot nodes + +Required properties: +- reg: should contain the slot id. +- bus-width: number of data lines connected to the controller + +Optional properties: +- cd-gpios: specify GPIOs for card detection +- cd-inverted: invert the value of external card detect gpio line +- wp-gpios: specify GPIOs for write protection + +Example slot node: + +slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 15 0> + cd-inverted; +}; + +Example full MCI node: +mmc0: mmc@f0008000 { + compatible = "atmel,hsmci"; + reg = <0xf0008000 0x600>; + interrupts = <12 4>; + #address-cells = <1>; + #size-cells = <0>; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 15 0> + cd-inverted; + }; + slot@1 { + reg = <1>; + bus-width = <4>; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt new file mode 100644 index 000000000000..792768953330 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt @@ -0,0 +1,87 @@ +* Samsung Exynos specific extensions to the Synopsis Designware Mobile + Storage Host Controller + +The Synopsis designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsis dw mshc controller properties described +by synposis-dw-mshc.txt and the properties used by the Samsung Exynos specific +extensions to the Synopsis Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - "samsung,exynos4210-dw-mshc": for controllers with Samsung Exynos4210 + specific extentions. + - "samsung,exynos4412-dw-mshc": for controllers with Samsung Exynos4412 + specific extentions. + - "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250 + specific extentions. + +* samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface + unit (ciu) clock. This property is applicable only for Exynos5 SoC's and + ignored for Exynos4 SoC's. The valid range of divider value is 0 to 7. + +* samsung,dw-mshc-sdr-timing: Specifies the value of CIU clock phase shift value + in transmit mode and CIU clock phase shift value in receive mode for single + data rate mode operation. Refer notes below for the order of the cells and the + valid values. + +* samsung,dw-mshc-ddr-timing: Specifies the value of CUI clock phase shift value + in transmit mode and CIU clock phase shift value in receive mode for double + data rate mode operation. Refer notes below for the order of the cells and the + valid values. + + Notes for the sdr-timing and ddr-timing values: + + The order of the cells should be + - First Cell: CIU clock phase shift value for tx mode. + - Second Cell: CIU clock phase shift value for rx mode. + + Valid values for SDR and DDR CIU clock timing for Exynos5250: + - valid value for tx phase shift and rx phase shift is 0 to 7. + - when CIU clock divider value is set to 3, all possible 8 phase shift + values can be used. + - if CIU clock divider value is 0 (that is divide by 1), both tx and rx + phase shift clocks should be 0. + +Required properties for a slot: + +* gpios: specifies a list of gpios used for command, clock and data bus. The + first gpio is the command line and the second gpio is the clock line. The + rest of the gpios (depending on the bus-width property) are the data lines in + no particular order. The format of the gpio specifier depends on the gpio + controller. + +Example: + + The MSHC controller node can be split into two portions, SoC specific and + board specific portions as listed below. + + dwmmc0@12200000 { + compatible = "samsung,exynos5250-dw-mshc"; + reg = <0x12200000 0x1000>; + interrupts = <0 75 0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + dwmmc0@12200000 { + num-slots = <1>; + supports-highspeed; + broken-cd; + fifo-depth = <0x80>; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + + slot@0 { + reg = <0>; + bus-width = <8>; + gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>, + <&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>, + <&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>, + <&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>, + <&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 8a6811f4a02f..8e2e0ba2f486 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -9,12 +9,17 @@ Interpreted by the OF core: Required properties: - bus-width: Number of data lines, can be <1>, <4>, or <8> +Card detection: +If no property below is supplied, standard SDHCI card detect is used. +Only one of the properties in this section should be supplied: + - broken-cd: There is no card detection available; polling must be used. + - cd-gpios: Specify GPIOs for card detection, see gpio binding + - non-removable: non-removable slot (like eMMC); assume always present. + Optional properties: -- cd-gpios: Specify GPIOs for card detection, see gpio binding - wp-gpios: Specify GPIOs for write protection, see gpio binding - cd-inverted: when present, polarity on the cd gpio line is inverted - wp-inverted: when present, polarity on the wp gpio line is inverted -- non-removable: non-removable slot (like eMMC) - max-frequency: maximum operating clock frequency Example: diff --git a/Documentation/devicetree/bindings/mmc/pxa-mmc.txt b/Documentation/devicetree/bindings/mmc/pxa-mmc.txt new file mode 100644 index 000000000000..b7025de7dced --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/pxa-mmc.txt @@ -0,0 +1,25 @@ +* PXA MMC drivers + +Driver bindings for the PXA MCI (MMC/SDIO) interfaces + +Required properties: +- compatible: Should be "marvell,pxa-mmc". +- vmmc-supply: A regulator for VMMC + +Optional properties: +- marvell,detect-delay-ms: sets the detection delay timeout in ms. +- marvell,gpio-power: GPIO spec for the card power enable pin + +This file documents differences between the core properties in mmc.txt +and the properties used by the pxa-mmc driver. + +Examples: + +mmc0: mmc@41100000 { + compatible = "marvell,pxa-mmc"; + reg = <0x41100000 0x1000>; + interrupts = <23>; + cd-gpios = <&gpio 23 0>; + wp-gpios = <&gpio 24 0>; +}; + diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt new file mode 100644 index 000000000000..630a7d7f4718 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt @@ -0,0 +1,53 @@ +* Samsung's SDHCI Controller device tree bindings + +Samsung's SDHCI controller is used as a connectivity interface with external +MMC, SD and eMMC storage mediums. This file documents differences between the +core mmc properties described by mmc.txt and the properties used by the +Samsung implmentation of the SDHCI controller. + +Note: The mmc core bindings documentation states that if none of the core +card-detect bindings are used, then the standard sdhci card detect mechanism +is used. The Samsung's SDHCI controller bindings extends this as listed below. + +[A] The property "samsung,cd-pinmux-gpio" can be used as stated in the + "Optional Board Specific Properties" section below. + +[B] If core card-detect bindings and "samsung,cd-pinmux-gpio" property + is not specified, it is assumed that there is no card detection + mechanism used. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci + controller. + - "samsung,exynos4210-sdhci": For controllers compatible with Exynos4 sdhci + controller. + +Required Board Specific Properties: +- gpios: Should specify the gpios used for clock, command and data lines. The + gpio specifier format depends on the gpio controller. + +Optional Board Specific Properties: +- samsung,cd-pinmux-gpio: Specifies the card detect line that is routed + through a pinmux to the card-detect pin of the card slot. This property + should be used only if none of the mmc core card-detect properties are + used. + +Example: + sdhci@12530000 { + compatible = "samsung,exynos4210-sdhci"; + reg = <0x12530000 0x100>; + interrupts = <0 75 0>; + bus-width = <4>; + cd-gpios = <&gpk2 2 2 3 3>; + gpios = <&gpk2 0 2 0 3>, /* clock line */ + <&gpk2 1 2 0 3>, /* command line */ + <&gpk2 3 2 3 3>, /* data line 0 */ + <&gpk2 4 2 3 3>, /* data line 1 */ + <&gpk2 5 2 3 3>, /* data line 2 */ + <&gpk2 6 2 3 3>; /* data line 3 */ + }; + + Note: This example shows both SoC specific and board specific properties + in a single device node. The properties can be actually be seperated + into SoC specific node and board specific node. diff --git a/Documentation/devicetree/bindings/mmc/sdhci-dove.txt b/Documentation/devicetree/bindings/mmc/sdhci-dove.txt new file mode 100644 index 000000000000..ae9aab9abcd7 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-dove.txt @@ -0,0 +1,14 @@ +* Marvell sdhci-dove controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-pxav2 and sdhci-pxav3 drivers. + +- compatible: Should be "marvell,dove-sdhci". + +Example: + +sdio0: sdio@92000 { + compatible = "marvell,dove-sdhci"; + reg = <0x92000 0x100>; + interrupts = <35>; +}; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-spear.txt b/Documentation/devicetree/bindings/mmc/sdhci-spear.txt new file mode 100644 index 000000000000..fd3643e7e467 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-spear.txt @@ -0,0 +1,18 @@ +* SPEAr SDHCI Controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-spear driver. + +Required properties: +- compatible: "st,spear300-sdhci" + +Optional properties: +- cd-gpios: card detect gpio, with zero flags. + +Example: + + sdhci@fc000000 { + compatible = "st,spear300-sdhci"; + reg = <0xfc000000 0x1000>; + cd-gpios = <&gpio0 6 0>; + }; diff --git a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt new file mode 100644 index 000000000000..06cd32d08052 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt @@ -0,0 +1,79 @@ +* Synopsis Designware Mobile Storage Host Controller + +The Synopsis designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core mmc properties described by mmc.txt and the +properties used by the Synopsis Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - snps,dw-mshc: for controllers compliant with synopsis dw-mshc. +* #address-cells: should be 1. +* #size-cells: should be 0. + +# Slots: The slot specific information are contained within child-nodes with + each child-node representing a supported slot. There should be atleast one + child node representing a card slot. The name of the child node representing + the slot is recommended to be slot@n where n is the unique number of the slot + connnected to the controller. The following are optional properties which + can be included in the slot child node. + + * reg: specifies the physical slot number. The valid values of this + property is 0 to (num-slots -1), where num-slots is the value + specified by the num-slots property. + + * bus-width: as documented in mmc core bindings. + + * wp-gpios: specifies the write protect gpio line. The format of the + gpio specifier depends on the gpio controller. If the write-protect + line is not available, this property is optional. + +Optional properties: + +* num-slots: specifies the number of slots supported by the controller. + The number of physical slots actually used could be equal or less than the + value specified by num-slots. If this property is not specified, the value + of num-slot property is assumed to be 1. + +* fifo-depth: The maximum size of the tx/rx fifo's. If this property is not + specified, the default value of the fifo size is determined from the + controller registers. + +* card-detect-delay: Delay in milli-seconds before detecting card after card + insert event. The default value is 0. + +* supports-highspeed: Enables support for high speed cards (upto 50MHz) + +* broken-cd: as documented in mmc core bindings. + +Aliases: + +- All the MSHC controller nodes should be represented in the aliases node using + the following format 'mshc{n}' where n is a unique number for the alias. + +Example: + +The MSHC controller node can be split into two portions, SoC specific and +board specific portions as listed below. + + dwmmc0@12200000 { + compatible = "snps,dw-mshc"; + reg = <0x12200000 0x1000>; + interrupts = <0 75 0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + dwmmc0@12200000 { + num-slots = <1>; + supports-highspeed; + broken-cd; + fifo-depth = <0x80>; + card-detect-delay = <200>; + + slot@0 { + reg = <0>; + bus-width = <8>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index a20069502f5a..d555421ea49f 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -3,7 +3,9 @@ Atmel NAND flash Required properties: - compatible : "atmel,at91rm9200-nand". - reg : should specify localbus address and size used for the chip, - and if availlable the ECC. + and hardware ECC controller if available. + If the hardware ECC is PMECC, it should contain address and size for + PMECC, PMECC Error Location controller and ROM which has lookup tables. - atmel,nand-addr-offset : offset for the address latch. - atmel,nand-cmd-offset : offset for the command latch. - #address-cells, #size-cells : Must be present if the device has sub-nodes @@ -16,6 +18,15 @@ Optional properties: - nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default. Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", "soft_bch". +- atmel,has-pmecc : boolean to enable Programmable Multibit ECC hardware. + Only supported by at91sam9x5 or later sam9 product. +- atmel,pmecc-cap : error correct capability for Programmable Multibit ECC + Controller. Supported values are: 2, 4, 8, 12, 24. +- atmel,pmecc-sector-size : sector size for ECC computation. Supported values + are: 512, 1024. +- atmel,pmecc-lookup-table-offset : includes two offsets of lookup table in ROM + for different sector size. First one is for sector size 512, the next is for + sector size 1024. - nand-bus-width : 8 or 16 bus width if not present 8 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false @@ -39,3 +50,30 @@ nand0: nand@40000000,0 { ... }; }; + +/* for PMECC supported chips */ +nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = < 0x40000000 0x10000000 /* bus addr & size */ + 0xffffe000 0x00000600 /* PMECC addr & size */ + 0xffffe600 0x00000200 /* PMECC ERRLOC addr & size */ + 0x00100000 0x00100000 /* ROM addr & size */ + >; + atmel,nand-addr-offset = <21>; /* ale */ + atmel,nand-cmd-offset = <22>; /* cle */ + nand-on-flash-bbt; + nand-ecc-mode = "hw"; + atmel,has-pmecc; /* enable PMECC */ + atmel,pmecc-cap = <2>; + atmel,pmecc-sector-size = <512>; + atmel,pmecc-lookup-table-offset = <0x8000 0x10000>; + gpios = <&pioD 5 0 /* rdy */ + &pioD 4 0 /* nce */ + 0 /* cd */ + >; + partition@0 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt index 1a5bbd346d22..3fb3f9015365 100644 --- a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt @@ -12,6 +12,10 @@ Required properties: - interrupt-names : The interrupt names "gpmi-dma", "bch"; - fsl,gpmi-dma-channel : Should contain the dma channel it uses. +Optional properties: + - nand-on-flash-bbt: boolean to enable on flash bbt option if not + present false + The device tree may optionally contain sub-nodes describing partitions of the address space. See partition.txt for more detail. diff --git a/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt b/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt new file mode 100644 index 000000000000..d0a37252eb22 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt @@ -0,0 +1,50 @@ +NXP LPC32xx SoC NAND MLC controller + +Required properties: +- compatible: "nxp,lpc3220-mlc" +- reg: Address and size of the controller +- interrupts: The NAND interrupt specification +- gpios: GPIO specification for NAND write protect + +The following required properties are very controller specific. See the LPC32xx +User Manual 7.5.14 MLC NAND Timing Register (the values here are specified in +Hz, to make them independent of actual clock speed and to provide for good +accuracy:) +- nxp,tcea_delay: TCEA_DELAY +- nxp,busy_delay: BUSY_DELAY +- nxp,nand_ta: NAND_TA +- nxp,rd_high: RD_HIGH +- nxp,rd_low: RD_LOW +- nxp,wr_high: WR_HIGH +- nxp,wr_low: WR_LOW + +Optional subnodes: +- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt + +Example: + + mlc: flash@200A8000 { + compatible = "nxp,lpc3220-mlc"; + reg = <0x200A8000 0x11000>; + interrupts = <11 0>; + #address-cells = <1>; + #size-cells = <1>; + + nxp,tcea-delay = <333333333>; + nxp,busy-delay = <10000000>; + nxp,nand-ta = <18181818>; + nxp,rd-high = <31250000>; + nxp,rd-low = <45454545>; + nxp,wr-high = <40000000>; + nxp,wr-low = <83333333>; + gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ + + mtd0@00000000 { + label = "boot"; + reg = <0x00000000 0x00064000>; + read-only; + }; + + ... + + }; diff --git a/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt b/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt new file mode 100644 index 000000000000..d94edc0fc554 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt @@ -0,0 +1,52 @@ +NXP LPC32xx SoC NAND SLC controller + +Required properties: +- compatible: "nxp,lpc3220-slc" +- reg: Address and size of the controller +- nand-on-flash-bbt: Use bad block table on flash +- gpios: GPIO specification for NAND write protect + +The following required properties are very controller specific. See the LPC32xx +User Manual: +- nxp,wdr-clks: Delay before Ready signal is tested on write (W_RDY) +- nxp,rdr-clks: Delay before Ready signal is tested on read (R_RDY) +(The following values are specified in Hz, to make them independent of actual +clock speed:) +- nxp,wwidth: Write pulse width (W_WIDTH) +- nxp,whold: Write hold time (W_HOLD) +- nxp,wsetup: Write setup time (W_SETUP) +- nxp,rwidth: Read pulse width (R_WIDTH) +- nxp,rhold: Read hold time (R_HOLD) +- nxp,rsetup: Read setup time (R_SETUP) + +Optional subnodes: +- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt + +Example: + + slc: flash@20020000 { + compatible = "nxp,lpc3220-slc"; + reg = <0x20020000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + nxp,wdr-clks = <14>; + nxp,wwidth = <40000000>; + nxp,whold = <100000000>; + nxp,wsetup = <100000000>; + nxp,rdr-clks = <14>; + nxp,rwidth = <40000000>; + nxp,rhold = <66666666>; + nxp,rsetup = <100000000>; + nand-on-flash-bbt; + gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ + + mtd0@00000000 { + label = "phy3250-boot"; + reg = <0x00000000 0x00064000>; + read-only; + }; + + ... + + }; diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index a63c2bd7de2b..94de19b8f16b 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -16,6 +16,13 @@ file systems on embedded devices. - #address-cells, #size-cells : Must be present if the device has sub-nodes representing partitions (see below). In this case both #address-cells and #size-cells must be equal to 1. + - no-unaligned-direct-access: boolean to disable the default direct + mapping of the flash. + On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause + problems with JFFS2 usage, as the local bus (LPB) doesn't support + unaligned accesses as implemented in the JFFS2 code via memcpy(). + By defining "no-unaligned-direct-access", the flash will not be + exposed directly to the MTD users (e.g. JFFS2) any more. For JEDEC compatible devices, the following additional properties are defined: diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt new file mode 100644 index 000000000000..daa768956069 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt @@ -0,0 +1,83 @@ +Lantiq FALCON pinmux controller + +Required properties: +- compatible: "lantiq,pinctrl-falcon" +- reg: Should contain the physical address and length of the gpio/pinmux + register range + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Lantiq's pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those group(s), and two pin configuration parameters: +pull-up and open-drain + +The name of each subnode is not important as long as it is unique; all subnodes +should be enumerated and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +We support 2 types of nodes. + +Definition of mux function groups: + +Required subnode-properties: +- lantiq,groups : An array of strings. Each string contains the name of a group. + Valid values for these names are listed below. +- lantiq,function: A string containing the name of the function to mux to the + group. Valid values for function names are listed below. + +Valid values for group and function names: + + mux groups: + por, ntr, ntr8k, hrst, mdio, bootled, asc0, spi, spi cs0, spi cs1, i2c, + jtag, slic, pcm, asc1 + + functions: + rst, ntr, mdio, led, asc, spi, i2c, jtag, slic, pcm + + +Definition of pin configurations: + +Required subnode-properties: +- lantiq,pins : An array of strings. Each string contains the name of a pin. + Valid values for these names are listed below. + +Optional subnode-properties: +- lantiq,pull: Integer, representing the pull-down/up to apply to the pin. + 0: none, 1: down +- lantiq,drive-current: Boolean, enables drive-current +- lantiq,slew-rate: Boolean, enables slew-rate + +Example: + pinmux0 { + compatible = "lantiq,pinctrl-falcon"; + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + asc0 { + lantiq,groups = "asc0"; + lantiq,function = "asc"; + }; + ntr { + lantiq,groups = "ntr8k"; + lantiq,function = "ntr"; + }; + i2c { + lantiq,groups = "i2c"; + lantiq,function = "i2c"; + }; + hrst { + lantiq,groups = "hrst"; + lantiq,function = "rst"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt new file mode 100644 index 000000000000..b5469db1d7ad --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt @@ -0,0 +1,97 @@ +Lantiq XWAY pinmux controller + +Required properties: +- compatible: "lantiq,pinctrl-xway" or "lantiq,pinctrl-xr9" +- reg: Should contain the physical address and length of the gpio/pinmux + register range + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Lantiq's pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those group(s), and two pin configuration parameters: +pull-up and open-drain + +The name of each subnode is not important as long as it is unique; all subnodes +should be enumerated and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +We support 2 types of nodes. + +Definition of mux function groups: + +Required subnode-properties: +- lantiq,groups : An array of strings. Each string contains the name of a group. + Valid values for these names are listed below. +- lantiq,function: A string containing the name of the function to mux to the + group. Valid values for function names are listed below. + +Valid values for group and function names: + + mux groups: + exin0, exin1, exin2, jtag, ebu a23, ebu a24, ebu a25, ebu clk, ebu cs1, + ebu wait, nand ale, nand cs1, nand cle, spi, spi_cs1, spi_cs2, spi_cs3, + spi_cs4, spi_cs5, spi_cs6, asc0, asc0 cts rts, stp, nmi , gpt1, gpt2, + gpt3, clkout0, clkout1, clkout2, clkout3, gnt1, gnt2, gnt3, req1, req2, + req3 + + additional mux groups (XR9 only): + mdio, nand rdy, nand rd, exin3, exin4, gnt4, req4 + + functions: + spi, asc, cgu, jtag, exin, stp, gpt, nmi, pci, ebu, mdio + + + +Definition of pin configurations: + +Required subnode-properties: +- lantiq,pins : An array of strings. Each string contains the name of a pin. + Valid values for these names are listed below. + +Optional subnode-properties: +- lantiq,pull: Integer, representing the pull-down/up to apply to the pin. + 0: none, 1: down, 2: up. +- lantiq,open-drain: Boolean, enables open-drain on the defined pin. + +Valid values for XWAY pin names: + Pinconf pins can be referenced via the names io0-io31. + +Valid values for XR9 pin names: + Pinconf pins can be referenced via the names io0-io55. + +Example: + gpio: pinmux@E100B10 { + compatible = "lantiq,pinctrl-xway"; + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + #gpio-cells = <2>; + gpio-controller; + reg = <0xE100B10 0xA0>; + + state_default: pinmux { + stp { + lantiq,groups = "stp"; + lantiq,function = "stp"; + }; + pci { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + }; + conf_out { + lantiq,pins = "io4", "io5", "io6"; /* stp */ + lantiq,open-drain; + lantiq,pull = <0>; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/pwm/imx-pwm.txt b/Documentation/devicetree/bindings/pwm/imx-pwm.txt new file mode 100644 index 000000000000..8522bfbccfd7 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/imx-pwm.txt @@ -0,0 +1,17 @@ +Freescale i.MX PWM controller + +Required properties: +- compatible: should be "fsl,<soc>-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. +- interrupts: The interrupt for the pwm controller + +Example: + +pwm1: pwm@53fb4000 { + #pwm-cells = <2>; + compatible = "fsl,imx53-pwm", "fsl,imx27-pwm"; + reg = <0x53fb4000 0x4000>; + interrupts = <61>; +}; diff --git a/Documentation/devicetree/bindings/pwm/mxs-pwm.txt b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt index 11963e4d6bc4..9e3f8f1d46a2 100644 --- a/Documentation/devicetree/bindings/pwm/mxs-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt @@ -4,7 +4,7 @@ Required properties: - compatible: should be "fsl,imx23-pwm" - reg: physical base address and length of the controller's registers - #pwm-cells: should be 2. The first cell specifies the per-chip index - of the PWM to use and the second cell is the duty cycle in nanoseconds. + of the PWM to use and the second cell is the period in nanoseconds. - fsl,pwm-number: the number of PWM devices Example: diff --git a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt index bbbeedb4ec05..01438ecd6628 100644 --- a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt @@ -7,7 +7,7 @@ Required properties: - reg: physical base address and length of the controller's registers - #pwm-cells: On Tegra the number of cells used to specify a PWM is 2. The first cell specifies the per-chip index of the PWM to use and the second - cell is the duty cycle in nanoseconds. + cell is the period in nanoseconds. Example: diff --git a/Documentation/devicetree/bindings/sound/cs4270.txt b/Documentation/devicetree/bindings/sound/cs4270.txt new file mode 100644 index 000000000000..6b222f9b8ef5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs4270.txt @@ -0,0 +1,21 @@ +CS4270 audio CODEC + +The driver for this device currently only supports I2C. + +Required properties: + + - compatible : "cirrus,cs4270" + + - reg : the I2C address of the device for I2C + +Optional properties: + + - reset-gpio : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + +Example: + +codec: cs4270@48 { + compatible = "cirrus,cs4270"; + reg = <0x48>; +}; diff --git a/Documentation/devicetree/bindings/sound/cs4271.txt b/Documentation/devicetree/bindings/sound/cs4271.txt new file mode 100644 index 000000000000..c81b5fd5a5bc --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs4271.txt @@ -0,0 +1,36 @@ +Cirrus Logic CS4271 DT bindings + +This driver supports both the I2C and the SPI bus. + +Required properties: + + - compatible: "cirrus,cs4271" + +For required properties on SPI, please consult +Documentation/devicetree/bindings/spi/spi-bus.txt + +Required properties on I2C: + + - reg: the i2c address + + +Optional properties: + + - reset-gpio: a GPIO spec to define which pin is connected to the chip's + !RESET pin + +Examples: + + codec_i2c: cs4271@10 { + compatible = "cirrus,cs4271"; + reg = <0x10>; + reset-gpio = <&gpio 23 0>; + }; + + codec_spi: cs4271@0 { + compatible = "cirrus,cs4271"; + reg = <0x0>; + reset-gpio = <&gpio 23 0>; + spi-max-frequency = <6000000>; + }; + diff --git a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt new file mode 100644 index 000000000000..374e145c2ef1 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt @@ -0,0 +1,45 @@ +Texas Instruments McASP controller + +Required properties: +- compatible : + "ti,dm646x-mcasp-audio" : for DM646x platforms + "ti,da830-mcasp-audio" : for both DA830 & DA850 platforms + "ti,omap2-mcasp-audio" : for OMAP2 platforms (TI81xx, AM33xx) + +- reg : Should contain McASP registers offset and length +- interrupts : Interrupt number for McASP +- op-mode : I2S/DIT ops mode. +- tdm-slots : Slots for TDM operation. +- num-serializer : Serializers used by McASP. +- serial-dir : A list of serializer pin mode. The list number should be equal + to "num-serializer" parameter. Each entry is a number indication + serializer pin direction. (0 - INACTIVE, 1 - TX, 2 - RX) + + +Optional properties: + +- ti,hwmods : Must be "mcasp<n>", n is controller instance starting 0 +- tx-num-evt : FIFO levels. +- rx-num-evt : FIFO levels. +- sram-size-playback : size of sram to be allocated during playback +- sram-size-capture : size of sram to be allocated during capture + +Example: + +mcasp0: mcasp0@1d00000 { + compatible = "ti,da830-mcasp-audio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x100000 0x3000>; + interrupts = <82 83>; + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + num-serializer = <16>; + serial-dir = < + 0 0 0 0 /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 0 0 + 0 0 0 1 + 2 0 0 0 >; + tx-num-evt = <1>; + rx-num-evt = <1>; +}; diff --git a/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt b/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt new file mode 100644 index 000000000000..65dec876cb2d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt @@ -0,0 +1,91 @@ +* Texas Instruments OMAP4+ and twl6040 based audio setups + +Required properties: +- compatible: "ti,abe-twl6040" +- ti,model: Name of the sound card ( for example "SDP4430") +- ti,mclk-freq: MCLK frequency for HPPLL operation +- ti,mcpdm: phandle for the McPDM node +- ti,twl6040: phandle for the twl6040 core node +- ti,audio-routing: List of connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. + +Optional properties: +- ti,dmic: phandle for the OMAP dmic node if the machine have it connected +- ti,jack_detection: Need to be set to <1> if the board capable to detect jack + insertion, removal. + +Available audio endpoints for the audio-routing table: + +Board connectors: + * Headset Stereophone + * Earphone Spk + * Ext Spk + * Line Out + * Vibrator + * Headset Mic + * Main Handset Mic + * Sub Handset Mic + * Line In + * Digital Mic + +twl6040 pins: + * HSOL + * HSOR + * EP + * HFL + * HFR + * AUXL + * AUXR + * VIBRAL + * VIBRAR + * HSMIC + * MAINMIC + * SUBMIC + * AFML + * AFMR + + * Headset Mic Bias + * Main Mic Bias + * Digital Mic1 Bias + * Digital Mic2 Bias + +Digital mic pins: + * DMic + +Example: + +sound { + compatible = "ti,abe-twl6040"; + ti,model = "SDP4430"; + + ti,jack-detection = <1>; + ti,mclk-freq = <38400000>; + + ti,mcpdm = <&mcpdm>; + ti,dmic = <&dmic>; + + ti,twl6040 = <&twl6040>; + + /* Audio routing */ + ti,audio-routing = + "Headset Stereophone", "HSOL", + "Headset Stereophone", "HSOR", + "Earphone Spk", "EP", + "Ext Spk", "HFL", + "Ext Spk", "HFR", + "Line Out", "AUXL", + "Line Out", "AUXR", + "Vibrator", "VIBRAL", + "Vibrator", "VIBRAR", + "HSMIC", "Headset Mic", + "Headset Mic", "Headset Mic Bias", + "MAINMIC", "Main Handset Mic", + "Main Handset Mic", "Main Mic Bias", + "SUBMIC", "Sub Handset Mic", + "Sub Handset Mic", "Main Mic Bias", + "AFML", "Line In", + "AFMR", "Line In", + "DMic", "Digital Mic", + "Digital Mic", "Digital Mic1 Bias"; +}; diff --git a/Documentation/devicetree/bindings/sound/omap-mcbsp.txt b/Documentation/devicetree/bindings/sound/omap-mcbsp.txt new file mode 100644 index 000000000000..17cce4490456 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/omap-mcbsp.txt @@ -0,0 +1,37 @@ +* Texas Instruments OMAP2+ McBSP module + +Required properties: +- compatible: "ti,omap2420-mcbsp" for McBSP on OMAP2420 + "ti,omap2430-mcbsp" for McBSP on OMAP2430 + "ti,omap3-mcbsp" for McBSP on OMAP3 + "ti,omap4-mcbsp" for McBSP on OMAP4 and newer SoC +- reg: Register location and size, for OMAP4+ as an array: + <MPU access base address, size>, + <L3 interconnect address, size>; +- reg-names: Array of strings associated with the address space +- interrupts: Interrupt numbers for the McBSP port, as an array in case the + McBSP IP have more interrupt lines: + <OCP compliant irq>, + <TX irq>, + <RX irq>; +- interrupt-names: Array of strings associated with the interrupt numbers +- interrupt-parent: The parent interrupt controller +- ti,buffer-size: Size of the FIFO on the port (OMAP2430 and newer SoC) +- ti,hwmods: Name of the hwmod associated to the McBSP port + +Example: + +mcbsp2: mcbsp@49022000 { + compatible = "ti,omap3-mcbsp"; + reg = <0x49022000 0xff>, + <0x49028000 0xff>; + reg-names = "mpu", "sidetone"; + interrupts = <0 17 0x4>, /* OCP compliant interrupt */ + <0 62 0x4>, /* TX interrupt */ + <0 63 0x4>, /* RX interrupt */ + <0 4 0x4>; /* Sidetone */ + interrupt-names = "common", "tx", "rx", "sidetone"; + interrupt-parent = <&intc>; + ti,buffer-size = <1280>; + ti,hwmods = "mcbsp2"; +}; diff --git a/Documentation/devicetree/bindings/sound/omap-twl4030.txt b/Documentation/devicetree/bindings/sound/omap-twl4030.txt new file mode 100644 index 000000000000..6fae51c7f766 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/omap-twl4030.txt @@ -0,0 +1,17 @@ +* Texas Instruments SoC with twl4030 based audio setups + +Required properties: +- compatible: "ti,omap-twl4030" +- ti,model: Name of the sound card (for example "omap3beagle") +- ti,mcbsp: phandle for the McBSP node +- ti,codec: phandle for the twl4030 audio node + +Example: + +sound { + compatible = "ti,omap-twl4030"; + ti,model = "omap3beagle"; + + ti,mcbsp = <&mcbsp2>; + ti,codec = <&twl_audio>; +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt new file mode 100644 index 000000000000..e7b98f41fa5f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt @@ -0,0 +1,20 @@ +Texas Instruments - tlv320aic3x Codec module + +The tlv320aic3x serial control bus communicates through I2C protocols + +Required properties: +- compatible - "string" - "ti,tlv320aic3x" +- reg - <int> - I2C slave address + + +Optional properties: + +- gpio-reset - gpio pin number used for codec reset +- ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality + +Example: + +tlv320aic3x: tlv320aic3x@1b { + compatible = "ti,tlv320aic3x"; + reg = <0x1b>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-octeon.txt b/Documentation/devicetree/bindings/spi/spi-octeon.txt new file mode 100644 index 000000000000..431add192342 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-octeon.txt @@ -0,0 +1,33 @@ +Cavium, Inc. OCTEON SOC SPI master controller. + +Required properties: +- compatible : "cavium,octeon-3010-spi" +- reg : The register base for the controller. +- interrupts : One interrupt, used by the controller. +- #address-cells : <1>, as required by generic SPI binding. +- #size-cells : <0>, also as required by generic SPI binding. + +Child nodes as per the generic SPI binding. + +Example: + + spi@1070000001000 { + compatible = "cavium,octeon-3010-spi"; + reg = <0x10700 0x00001000 0x0 0x100>; + interrupts = <0 58>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + compatible = "st,m95256", "atmel,at25"; + reg = <0>; + spi-max-frequency = <5000000>; + spi-cpha; + spi-cpol; + + pagesize = <64>; + size = <32768>; + address-width = <16>; + }; + }; + |
