diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
7 files changed, 131 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index ecc81e368715..d187e9f7cf1c 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -8,7 +8,7 @@ PIT Timer required properties: shared across all System Controller members. TC/TCLIB Timer required properties: -- compatible: Should be "atmel,<chip>-pit". +- compatible: Should be "atmel,<chip>-tcb". <chip> can be "at91rm9200" or "at91sam9x5" - reg: Should contain registers location and length - interrupts: Should contain all interrupts for the TC block diff --git a/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt new file mode 100644 index 000000000000..df70318a617f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt @@ -0,0 +1,19 @@ +* EETI eGalax Multiple Touch Controller + +Required properties: +- compatible: must be "eeti,egalax_ts" +- reg: i2c slave address +- interrupt-parent: the phandle for the interrupt controller +- interrupts: touch controller interrupt +- wakeup-gpios: the gpio pin to be used for waking up the controller + as well as uased as irq pin + +Example: + + egalax_ts@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio1>; + interrupts = <9 2>; + wakeup-gpios = <&gpio1 9 0>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt index c8e578263ce2..683fde93c4fb 100644 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt @@ -93,7 +93,7 @@ Valid values for pin and group names are: With some exceptions, these support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode, nvidia,pull-down-strength, - nvidia,pull-up-strength, nvidia,slew_rate-rising, nvidia,slew_rate-falling. + nvidia,pull-up-strength, nvidia,slew-rate-rising, nvidia,slew-rate-falling. drive_ao1, drive_ao2, drive_at1, drive_at2, drive_cdev1, drive_cdev2, drive_csus, drive_dap1, drive_dap2, drive_dap3, drive_dap4, drive_dbg, diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt index c275b70349c1..6f426ed7009e 100644 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt @@ -83,7 +83,7 @@ Valid values for pin and group names are: drive groups: These all support nvidia,pull-down-strength, nvidia,pull-up-strength, - nvidia,slew_rate-rising, nvidia,slew_rate-falling. Most but not all + nvidia,slew-rate-rising, nvidia,slew-rate-falling. Most but not all support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode. ao1, ao2, at1, at2, at3, at4, at5, cdev1, cdev2, cec, crt, csus, dap1, diff --git a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt new file mode 100644 index 000000000000..63c659800c03 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt @@ -0,0 +1,37 @@ +GPIO controlled regulators + +Required properties: +- compatible : Must be "regulator-gpio". +- states : Selection of available voltages and GPIO configs. + if there are no states, then use a fixed regulator + +Optional properties: +- enable-gpio : GPIO to use to enable/disable the regulator. +- gpios : GPIO group used to control voltage. +- startup-delay-us : Startup time in microseconds. +- enable-active-high : Polarity of GPIO is active high (default is low). + +Any property defined as part of the core regulator binding defined in +regulator.txt can also be used. + +Example: + + mmciv: gpio-regulator { + compatible = "regulator-gpio"; + + regulator-name = "mmci-gpio-supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2600000>; + regulator-boot-on; + + enable-gpio = <&gpio0 23 0x4>; + gpios = <&gpio0 24 0x4 + &gpio0 25 0x4>; + states = <1800000 0x3 + 2200000 0x2 + 2600000 0x1 + 2900000 0x0>; + + startup-delay-us = <100000>; + enable-active-high; + }; diff --git a/Documentation/devicetree/bindings/regulator/max8925-regulator.txt b/Documentation/devicetree/bindings/regulator/max8925-regulator.txt new file mode 100644 index 000000000000..0057695aae8f --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8925-regulator.txt @@ -0,0 +1,40 @@ +Max8925 Voltage regulators + +Required nodes: +-nodes: + - SDV1 for SDV SDV1 + - SDV2 for SDV SDV2 + - SDV3 for SDV SDV3 + - LDO1 for LDO LDO1 + - LDO2 for LDO LDO2 + - LDO3 for LDO LDO3 + - LDO4 for LDO LDO4 + - LDO5 for LDO LDO5 + - LDO6 for LDO LDO6 + - LDO7 for LDO LDO7 + - LDO8 for LDO LDO8 + - LDO9 for LDO LDO9 + - LDO10 for LDO LDO10 + - LDO11 for LDO LDO11 + - LDO12 for LDO LDO12 + - LDO13 for LDO LDO13 + - LDO14 for LDO LDO14 + - LDO15 for LDO LDO15 + - LDO16 for LDO LDO16 + - LDO17 for LDO LDO17 + - LDO18 for LDO LDO18 + - LDO19 for LDO LDO19 + - LDO20 for LDO LDO20 + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: + + SDV1 { + regulator-min-microvolt = <637500>; + regulator-max-microvolt = <1425000>; + regulator-boot-on; + regulator-always-on; + }; + diff --git a/Documentation/devicetree/bindings/regulator/vexpress.txt b/Documentation/devicetree/bindings/regulator/vexpress.txt new file mode 100644 index 000000000000..d775f72487aa --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/vexpress.txt @@ -0,0 +1,32 @@ +Versatile Express voltage regulators +------------------------------------ + +Requires node properties: +- "compatible" value: "arm,vexpress-volt" +- "arm,vexpress-sysreg,func" when controlled via vexpress-sysreg + (see Documentation/devicetree/bindings/arm/vexpress-sysreg.txt + for more details) + +Required regulator properties: +- "regulator-name" +- "regulator-always-on" + +Optional regulator properties: +- "regulator-min-microvolt" +- "regulator-max-microvolt" + +See Documentation/devicetree/bindings/regulator/regulator.txt +for more details about the regulator properties. + +When no "regulator-[min|max]-microvolt" properties are defined, +the device is treated as fixed (or rather "read-only") regulator. + +Example: + volt@0 { + compatible = "arm,vexpress-volt"; + arm,vexpress-sysreg,func = <2 0>; + regulator-name = "Cores"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + }; |
