diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
9 files changed, 178 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt new file mode 100644 index 000000000000..ca8fa56e9f03 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt @@ -0,0 +1,14 @@ +AM33XX MUSB GLUE + - compatible : Should be "ti,musb-am33xx" + - ti,hwmods : must be "usb_otg_hs" + - multipoint : Should be "1" indicating the musb controller supports + multipoint. This is a MUSB configuration-specific setting. + - num_eps : Specifies the number of endpoints. This is also a + MUSB configuration-specific setting. Should be set to "16" + - ram_bits : Specifies the ram address size. Should be set to "12" + - port0_mode : Should be "3" to represent OTG. "1" signifies HOST and "2" + represents PERIPHERAL. + - port1_mode : Should be "1" to represent HOST. "3" signifies OTG and "2" + represents PERIPHERAL. + - power : Should be "250". This signifies the controller can supply upto + 500mA when operating in host mode. diff --git a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt index 2c290418bb2d..5778b9c83bd8 100644 --- a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt +++ b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt @@ -7,7 +7,10 @@ Required properties: Optional properties: - fsl,usbphy: phandler of usb phy that connects to the only one port +- fsl,usbmisc: phandler of non-core register device, with one argument + that indicate usb controller index - vbus-supply: regulator for vbus +- disable-over-current: disable over current detect Examples: usb@02184000 { /* USB OTG */ @@ -15,4 +18,6 @@ usb@02184000 { /* USB OTG */ reg = <0x02184000 0x200>; interrupts = <0 43 0x04>; fsl,usbphy = <&usbphy1>; + fsl,usbmisc = <&usbmisc 0>; + disable-over-current; }; diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt new file mode 100644 index 000000000000..29a043ecda52 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -0,0 +1,33 @@ +OMAP GLUE + +OMAP MUSB GLUE + - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb" + - ti,hwmods : must be "usb_otg_hs" + - multipoint : Should be "1" indicating the musb controller supports + multipoint. This is a MUSB configuration-specific setting. + - num_eps : Specifies the number of endpoints. This is also a + MUSB configuration-specific setting. Should be set to "16" + - ram_bits : Specifies the ram address size. Should be set to "12" + - interface_type : This is a board specific setting to describe the type of + interface between the controller and the phy. It should be "0" or "1" + specifying ULPI and UTMI respectively. + - mode : Should be "3" to represent OTG. "1" signifies HOST and "2" + represents PERIPHERAL. + - power : Should be "50". This signifies the controller can supply upto + 100mA when operating in host mode. + +SOC specific device node entry +usb_otg_hs: usb_otg_hs@4a0ab000 { + compatible = "ti,omap4-musb"; + ti,hwmods = "usb_otg_hs"; + multipoint = <1>; + num_eps = <16>; + ram_bits = <12>; +}; + +Board specific device node entry +&usb_otg_hs { + interface_type = <1>; + mode = <3>; + power = <50>; +}; diff --git a/Documentation/devicetree/bindings/usb/platform-uhci.txt b/Documentation/devicetree/bindings/usb/platform-uhci.txt new file mode 100644 index 000000000000..91477d6830ec --- /dev/null +++ b/Documentation/devicetree/bindings/usb/platform-uhci.txt @@ -0,0 +1,12 @@ +Generic Platform UHCI controllers. + +Required properties: + - compatible: Should be "platform-uhci". + - reg: Address range of the uhci registers + - interrupts: Should contain the uhci interrupt. + +usb: uhci@D8007301 { + compatible = "platform-uhci", "usb-uhci"; + reg = <0xD8007301 0x200>; + interrupts = <0>; +}; diff --git a/Documentation/devicetree/bindings/usb/pxa-usb.txt b/Documentation/devicetree/bindings/usb/pxa-usb.txt new file mode 100644 index 000000000000..79729a948d5a --- /dev/null +++ b/Documentation/devicetree/bindings/usb/pxa-usb.txt @@ -0,0 +1,31 @@ +PXA USB controllers + +OHCI + +Required properties: + - compatible: Should be "marvell,pxa-ohci" for USB controllers + used in host mode. + +Optional properties: + - "marvell,enable-port1", "marvell,enable-port2", "marvell,enable-port3" + If present, enables the appropriate USB port of the controller. + - "marvell,port-mode" selects the mode of the ports: + 1 = PMM_NPS_MODE + 2 = PMM_GLOBAL_MODE + 3 = PMM_PERPORT_MODE + - "marvell,power-sense-low" - power sense pin is low-active. + - "marvell,power-control-low" - power control pin is low-active. + - "marvell,no-oc-protection" - disable over-current protection. + - "marvell,oc-mode-perport" - enable per-port over-current protection. + - "marvell,power_on_delay" Power On to Power Good time - in ms. + +Example: + + usb0: ohci@4c000000 { + compatible = "marvell,pxa-ohci", "usb-ohci"; + reg = <0x4c000000 0x100000>; + interrupts = <18>; + marvell,enable-port1; + marvell,port-mode = <2>; /* PMM_GLOBAL_MODE */ + }; + diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt new file mode 100644 index 000000000000..36b9aede3f40 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt @@ -0,0 +1,40 @@ +USB COMPARATOR OF TWL CHIPS + +TWL6030 USB COMPARATOR + - compatible : Should be "ti,twl6030-usb" + - interrupts : Two interrupt numbers to the cpu should be specified. First + interrupt number is the otg interrupt number that raises ID interrupts when + the controller has to act as host and the second interrupt number is the + usb interrupt number that raises VBUS interrupts when the controller has to + act as device + - usb-supply : phandle to the regulator device tree node. It should be vusb + if it is twl6030 or ldousb if it is twl6025 subclass. + +twl6030-usb { + compatible = "ti,twl6030-usb"; + interrupts = < 4 10 >; +}; + +Board specific device node entry +&twl6030-usb { + usb-supply = <&vusb>; +}; + +TWL4030 USB PHY AND COMPARATOR + - compatible : Should be "ti,twl4030-usb" + - interrupts : The interrupt numbers to the cpu should be specified. First + interrupt number is the otg interrupt number that raises ID interrupts + and VBUS interrupts. The second interrupt number is optional. + - <supply-name>-supply : phandle to the regulator device tree node. + <supply-name> should be vusb1v5, vusb1v8 and vusb3v1 + - usb_mode : The mode used by the phy to connect to the controller. "1" + specifies "ULPI" mode and "2" specifies "CEA2011_3PIN" mode. + +twl4030-usb { + compatible = "ti,twl4030-usb"; + interrupts = < 10 4 >; + usb1v5-supply = <&vusb1v5>; + usb1v8-supply = <&vusb1v8>; + usb3v1-supply = <&vusb3v1>; + usb_mode = <1>; +}; diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt new file mode 100644 index 000000000000..80d4148cb661 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-phy.txt @@ -0,0 +1,17 @@ +USB PHY + +OMAP USB2 PHY + +Required properties: + - compatible: Should be "ti,omap-usb2" + - reg : Address and length of the register set for the device. Also +add the address of control module dev conf register until a driver for +control module is added + +This is usually a subnode of ocp2scp to which it is connected. + +usb2phy@4a0ad080 { + compatible = "ti,omap-usb2"; + reg = <0x4a0ad080 0x58>, + <0x4a002300 0x4>; +}; diff --git a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt new file mode 100644 index 000000000000..97ce94e1a6cc --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt @@ -0,0 +1,14 @@ +* Freescale i.MX non-core registers + +Required properties: +- #index-cells: Cells used to descibe usb controller index. Should be <1> +- compatible: Should be one of below: + "fsl,imx6q-usbmisc" for imx6q +- reg: Should contain registers location and length + +Examples: +usbmisc@02184800 { + #index-cells = <1>; + compatible = "fsl,imx6q-usbmisc"; + reg = <0x02184800 0x200>; +}; diff --git a/Documentation/devicetree/bindings/usb/vt8500-ehci.txt b/Documentation/devicetree/bindings/usb/vt8500-ehci.txt new file mode 100644 index 000000000000..5fb8fd6e250c --- /dev/null +++ b/Documentation/devicetree/bindings/usb/vt8500-ehci.txt @@ -0,0 +1,12 @@ +VIA VT8500 and Wondermedia WM8xxx SoC USB controllers. + +Required properties: + - compatible: Should be "via,vt8500-ehci" or "wm,prizm-ehci". + - reg: Address range of the ehci registers. size should be 0x200 + - interrupts: Should contain the ehci interrupt. + +usb: ehci@D8007100 { + compatible = "wm,prizm-ehci", "usb-ehci"; + reg = <0xD8007100 0x200>; + interrupts = <1>; +}; |
