diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
12 files changed, 542 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt b/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt new file mode 100644 index 000000000000..93986a5a8018 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt @@ -0,0 +1,30 @@ +* Compact Flash + +The Cavium Compact Flash device is connected to the Octeon Boot Bus, +and is thus a child of the Boot Bus device. It can read and write +industry standard compact flash devices. + +Properties: +- compatible: "cavium,ebt3000-compact-flash"; + + Compatibility with many Cavium evaluation boards. + +- reg: The base address of the the CF chip select banks. Depending on + the device configuration, there may be one or two banks. + +- cavium,bus-width: The width of the connection to the CF devices. Valid + values are 8 and 16. + +- cavium,true-ide: Optional, if present the CF connection is in True IDE mode. + +- cavium,dma-engine-handle: Optional, a phandle for the DMA Engine connected + to this device. + +Example: + compact-flash@5,0 { + compatible = "cavium,ebt3000-compact-flash"; + reg = <5 0 0x10000>, <6 0 0x10000>; + cavium,bus-width = <16>; + cavium,true-ide; + cavium,dma-engine-handle = <&dma0>; + }; diff --git a/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt new file mode 100644 index 000000000000..9d6dcd3fe7f9 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt @@ -0,0 +1,49 @@ +* General Purpose Input Output (GPIO) bus. + +Properties: +- compatible: "cavium,octeon-3860-gpio" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the GPIO unit's register bank. + +- gpio-controller: This is a GPIO controller. + +- #gpio-cells: Must be <2>. The first cell is the GPIO pin. + +- interrupt-controller: The GPIO controller is also an interrupt + controller, many of its pins may be configured as an interrupt + source. + +- #interrupt-cells: Must be <2>. The first cell is the GPIO pin + connected to the interrupt source. The second cell is the interrupt + triggering protocol and may have one of four values: + 1 - edge triggered on the rising edge. + 2 - edge triggered on the falling edge + 4 - level triggered active high. + 8 - level triggered active low. + +- interrupts: Interrupt routing for each pin. + +Example: + + gpio-controller@1070000000800 { + #gpio-cells = <2>; + compatible = "cavium,octeon-3860-gpio"; + reg = <0x10700 0x00000800 0x0 0x100>; + gpio-controller; + /* Interrupts are specified by two parts: + * 1) GPIO pin number (0..15) + * 2) Triggering (1 - edge rising + * 2 - edge falling + * 4 - level active high + * 8 - level active low) + */ + interrupt-controller; + #interrupt-cells = <2>; + /* The GPIO pin connect to 16 consecutive CUI bits */ + interrupts = <0 16>, <0 17>, <0 18>, <0 19>, + <0 20>, <0 21>, <0 22>, <0 23>, + <0 24>, <0 25>, <0 26>, <0 27>, + <0 28>, <0 29>, <0 30>, <0 31>; + }; diff --git a/Documentation/devicetree/bindings/i2c/cavium-i2c.txt b/Documentation/devicetree/bindings/i2c/cavium-i2c.txt new file mode 100644 index 000000000000..dced82ebe31d --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/cavium-i2c.txt @@ -0,0 +1,34 @@ +* Two Wire Serial Interface (TWSI) / I2C + +- compatible: "cavium,octeon-3860-twsi" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the TWSI/I2C bus controller register bank. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. I2C addresses have no size component. + +- interrupts: A single interrupt specifier. + +- clock-frequency: The I2C bus clock rate in Hz. + +Example: + twsi0: i2c@1180000001000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "cavium,octeon-3860-twsi"; + reg = <0x11800 0x00001000 0x0 0x200>; + interrupts = <0 45>; + clock-frequency = <100000>; + + rtc@68 { + compatible = "dallas,ds1337"; + reg = <0x68>; + }; + tmp@4c { + compatible = "ti,tmp421"; + reg = <0x4c>; + }; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/bootbus.txt b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt new file mode 100644 index 000000000000..6581478225a2 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt @@ -0,0 +1,126 @@ +* Boot Bus + +The Octeon Boot Bus is a configurable parallel bus with 8 chip +selects. Each chip select is independently configurable. + +Properties: +- compatible: "cavium,octeon-3860-bootbus" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the Boot Bus' register bank. + +- #address-cells: Must be <2>. The first cell is the chip select + within the bootbus. The second cell is the offset from the chip select. + +- #size-cells: Must be <1>. + +- ranges: There must be one one triplet of (child-bus-address, + parent-bus-address, length) for each active chip select. If the + length element for any triplet is zero, the chip select is disabled, + making it inactive. + +The configuration parameters for each chip select are stored in child +nodes. + +Configuration Properties: +- compatible: "cavium,octeon-3860-bootbus-config" + +- cavium,cs-index: A single cell indicating the chip select that + corresponds to this configuration. + +- cavium,t-adr: A cell specifying the ADR timing (in nS). + +- cavium,t-ce: A cell specifying the CE timing (in nS). + +- cavium,t-oe: A cell specifying the OE timing (in nS). + +- cavium,t-we: A cell specifying the WE timing (in nS). + +- cavium,t-rd-hld: A cell specifying the RD_HLD timing (in nS). + +- cavium,t-wr-hld: A cell specifying the WR_HLD timing (in nS). + +- cavium,t-pause: A cell specifying the PAUSE timing (in nS). + +- cavium,t-wait: A cell specifying the WAIT timing (in nS). + +- cavium,t-page: A cell specifying the PAGE timing (in nS). + +- cavium,t-rd-dly: A cell specifying the RD_DLY timing (in nS). + +- cavium,pages: A cell specifying the PAGES parameter (0 = 8 bytes, 1 + = 2 bytes, 2 = 4 bytes, 3 = 8 bytes). + +- cavium,wait-mode: Optional. If present, wait mode (WAITM) is selected. + +- cavium,page-mode: Optional. If present, page mode (PAGEM) is selected. + +- cavium,bus-width: A cell specifying the WIDTH parameter (in bits) of + the bus for this chip select. + +- cavium,ale-mode: Optional. If present, ALE mode is selected. + +- cavium,sam-mode: Optional. If present, SAM mode is selected. + +- cavium,or-mode: Optional. If present, OR mode is selected. + +Example: + bootbus: bootbus@1180000000000 { + compatible = "cavium,octeon-3860-bootbus"; + reg = <0x11800 0x00000000 0x0 0x200>; + /* The chip select number and offset */ + #address-cells = <2>; + /* The size of the chip select region */ + #size-cells = <1>; + ranges = <0 0 0x0 0x1f400000 0xc00000>, + <1 0 0x10000 0x30000000 0>, + <2 0 0x10000 0x40000000 0>, + <3 0 0x10000 0x50000000 0>, + <4 0 0x0 0x1d020000 0x10000>, + <5 0 0x0 0x1d040000 0x10000>, + <6 0 0x0 0x1d050000 0x10000>, + <7 0 0x10000 0x90000000 0>; + + cavium,cs-config@0 { + compatible = "cavium,octeon-3860-bootbus-config"; + cavium,cs-index = <0>; + cavium,t-adr = <20>; + cavium,t-ce = <60>; + cavium,t-oe = <60>; + cavium,t-we = <45>; + cavium,t-rd-hld = <35>; + cavium,t-wr-hld = <45>; + cavium,t-pause = <0>; + cavium,t-wait = <0>; + cavium,t-page = <35>; + cavium,t-rd-dly = <0>; + + cavium,pages = <0>; + cavium,bus-width = <8>; + }; + . + . + . + cavium,cs-config@6 { + compatible = "cavium,octeon-3860-bootbus-config"; + cavium,cs-index = <6>; + cavium,t-adr = <5>; + cavium,t-ce = <300>; + cavium,t-oe = <270>; + cavium,t-we = <150>; + cavium,t-rd-hld = <100>; + cavium,t-wr-hld = <70>; + cavium,t-pause = <0>; + cavium,t-wait = <0>; + cavium,t-page = <320>; + cavium,t-rd-dly = <0>; + + cavium,pages = <0>; + cavium,wait-mode; + cavium,bus-width = <16>; + }; + . + . + . + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu.txt b/Documentation/devicetree/bindings/mips/cavium/ciu.txt new file mode 100644 index 000000000000..2c2d0746b43d --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/ciu.txt @@ -0,0 +1,26 @@ +* Central Interrupt Unit + +Properties: +- compatible: "cavium,octeon-3860-ciu" + + Compatibility with all cn3XXX, cn5XXX and cn63XX SOCs. + +- interrupt-controller: This is an interrupt controller. + +- reg: The base address of the CIU's register bank. + +- #interrupt-cells: Must be <2>. The first cell is the bank within + the CIU and may have a value of 0 or 1. The second cell is the bit + within the bank and may have a value between 0 and 63. + +Example: + interrupt-controller@1070000000000 { + compatible = "cavium,octeon-3860-ciu"; + interrupt-controller; + /* Interrupts are specified by two parts: + * 1) Controller register (0 or 1) + * 2) Bit within the register (0..63) + */ + #interrupt-cells = <2>; + reg = <0x10700 0x00000000 0x0 0x7000>; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu2.txt b/Documentation/devicetree/bindings/mips/cavium/ciu2.txt new file mode 100644 index 000000000000..0ec7ba8bbbcb --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/ciu2.txt @@ -0,0 +1,27 @@ +* Central Interrupt Unit + +Properties: +- compatible: "cavium,octeon-6880-ciu2" + + Compatibility with 68XX SOCs. + +- interrupt-controller: This is an interrupt controller. + +- reg: The base address of the CIU's register bank. + +- #interrupt-cells: Must be <2>. The first cell is the bank within + the CIU and may have a value between 0 and 63. The second cell is + the bit within the bank and may also have a value between 0 and 63. + +Example: + interrupt-controller@1070100000000 { + compatible = "cavium,octeon-6880-ciu2"; + interrupt-controller; + /* Interrupts are specified by two parts: + * 1) Controller register (0..63) + * 2) Bit within the register (0..63) + */ + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x10701 0x00000000 0x0 0x4000000>; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt new file mode 100644 index 000000000000..cb4291e3b1d1 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt @@ -0,0 +1,21 @@ +* DMA Engine. + +The Octeon DMA Engine transfers between the Boot Bus and main memory. +The DMA Engine will be refered to by phandle by any device that is +connected to it. + +Properties: +- compatible: "cavium,octeon-5750-bootbus-dma" + + Compatibility with all cn52XX, cn56XX and cn6XXX SOCs. + +- reg: The base address of the DMA Engine's register bank. + +- interrupts: A single interrupt specifier. + +Example: + dma0: dma-engine@1180000000100 { + compatible = "cavium,octeon-5750-bootbus-dma"; + reg = <0x11800 0x00000100 0x0 0x8>; + interrupts = <0 63>; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/uctl.txt b/Documentation/devicetree/bindings/mips/cavium/uctl.txt new file mode 100644 index 000000000000..aa66b9b8d801 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/uctl.txt @@ -0,0 +1,46 @@ +* UCTL USB controller glue + +Properties: +- compatible: "cavium,octeon-6335-uctl" + + Compatibility with all cn6XXX SOCs. + +- reg: The base address of the UCTL register bank. + +- #address-cells: Must be <2>. + +- #size-cells: Must be <2>. + +- ranges: Empty to signify direct mapping of the children. + +- refclk-frequency: A single cell containing the reference clock + frequency in Hz. + +- refclk-type: A string describing the reference clock connection + either "crystal" or "external". + +Example: + uctl@118006f000000 { + compatible = "cavium,octeon-6335-uctl"; + reg = <0x11800 0x6f000000 0x0 0x100>; + ranges; /* Direct mapping */ + #address-cells = <2>; + #size-cells = <2>; + /* 12MHz, 24MHz and 48MHz allowed */ + refclk-frequency = <24000000>; + /* Either "crystal" or "external" */ + refclk-type = "crystal"; + + ehci@16f0000000000 { + compatible = "cavium,octeon-6335-ehci","usb-ehci"; + reg = <0x16f00 0x00000000 0x0 0x100>; + interrupts = <0 56>; + big-endian-regs; + }; + ohci@16f0000000400 { + compatible = "cavium,octeon-6335-ohci","usb-ohci"; + reg = <0x16f00 0x00000400 0x0 0x100>; + interrupts = <0 56>; + big-endian-regs; + }; + }; diff --git a/Documentation/devicetree/bindings/net/cavium-mdio.txt b/Documentation/devicetree/bindings/net/cavium-mdio.txt new file mode 100644 index 000000000000..04cb7491d232 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cavium-mdio.txt @@ -0,0 +1,27 @@ +* System Management Interface (SMI) / MDIO + +Properties: +- compatible: "cavium,octeon-3860-mdio" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the MDIO bus controller register bank. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. MDIO addresses have no size component. + +Typically an MDIO bus might have several children. + +Example: + mdio@1180000001800 { + compatible = "cavium,octeon-3860-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11800 0x00001800 0x0 0x40>; + + ethernet-phy@0 { + ... + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/cavium-mix.txt b/Documentation/devicetree/bindings/net/cavium-mix.txt new file mode 100644 index 000000000000..5da628db68bf --- /dev/null +++ b/Documentation/devicetree/bindings/net/cavium-mix.txt @@ -0,0 +1,39 @@ +* MIX Ethernet controller. + +Properties: +- compatible: "cavium,octeon-5750-mix" + + Compatibility with all cn5XXX and cn6XXX SOCs populated with MIX + devices. + +- reg: The base addresses of four separate register banks. The first + bank contains the MIX registers. The second bank the corresponding + AGL registers. The third bank are the AGL registers shared by all + MIX devices present. The fourth bank is the AGL_PRT_CTL shared by + all MIX devices present. + +- cell-index: A single cell specifying which portion of the shared + register banks corresponds to this MIX device. + +- interrupts: Two interrupt specifiers. The first is the MIX + interrupt routing and the second the routing for the AGL interrupts. + +- mac-address: Optional, the MAC address to assign to the device. + +- local-mac-address: Optional, the MAC address to assign to the device + if mac-address is not specified. + +- phy-handle: Optional, a phandle for the PHY device connected to this device. + +Example: + ethernet@1070000100800 { + compatible = "cavium,octeon-5750-mix"; + reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */ + <0x11800 0xE0000800 0x0 0x300>, /* AGL */ + <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED */ + <0x11800 0xE0002008 0x0 0x8>; /* AGL_PRT_CTL */ + cell-index = <1>; + interrupts = <1 18>, < 1 46>; + local-mac-address = [ 00 0f b7 10 63 54 ]; + phy-handle = <&phy1>; + }; diff --git a/Documentation/devicetree/bindings/net/cavium-pip.txt b/Documentation/devicetree/bindings/net/cavium-pip.txt new file mode 100644 index 000000000000..d4c53ba04b3b --- /dev/null +++ b/Documentation/devicetree/bindings/net/cavium-pip.txt @@ -0,0 +1,98 @@ +* PIP Ethernet nexus. + +The PIP Ethernet nexus can control several data packet input/output +devices. The devices have a two level grouping scheme. There may be +several interfaces, and each interface may have several ports. These +ports might be an individual Ethernet PHY. + + +Properties for the PIP nexus: +- compatible: "cavium,octeon-3860-pip" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the PIP's register bank. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. + +Properties for PIP interfaces which is a child the PIP nexus: +- compatible: "cavium,octeon-3860-pip-interface" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The interface number. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. + +Properties for PIP port which is a child the PIP interface: +- compatible: "cavium,octeon-3860-pip-port" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The port number within the interface group. + +- mac-address: Optional, the MAC address to assign to the device. + +- local-mac-address: Optional, the MAC address to assign to the device + if mac-address is not specified. + +- phy-handle: Optional, a phandle for the PHY device connected to this device. + +Example: + + pip@11800a0000000 { + compatible = "cavium,octeon-3860-pip"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11800 0xa0000000 0x0 0x2000>; + + interface@0 { + compatible = "cavium,octeon-3860-pip-interface"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; /* interface */ + + ethernet@0 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x0>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 60 ]; + phy-handle = <&phy2>; + }; + ethernet@1 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x1>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 61 ]; + phy-handle = <&phy3>; + }; + ethernet@2 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x2>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 62 ]; + phy-handle = <&phy4>; + }; + ethernet@3 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x3>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 63 ]; + phy-handle = <&phy5>; + }; + }; + + interface@1 { + compatible = "cavium,octeon-3860-pip-interface"; + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; /* interface */ + + ethernet@0 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x0>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 64 ]; + phy-handle = <&phy6>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/serial/cavium-uart.txt b/Documentation/devicetree/bindings/serial/cavium-uart.txt new file mode 100644 index 000000000000..87a6c375cd44 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/cavium-uart.txt @@ -0,0 +1,19 @@ +* Universal Asynchronous Receiver/Transmitter (UART) + +- compatible: "cavium,octeon-3860-uart" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the UART register bank. + +- interrupts: A single interrupt specifier. + +- current-speed: Optional, the current bit rate in bits per second. + +Example: + uart1: serial@1180000000c00 { + compatible = "cavium,octeon-3860-uart","ns16550"; + reg = <0x11800 0x00000c00 0x0 0x400>; + current-speed = <115200>; + interrupts = <0 35>; + }; |
