diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb/mt8173-mtu3.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/usb/mt8173-mtu3.txt | 87 |
1 files changed, 87 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt new file mode 100644 index 000000000000..e049d199bf0d --- /dev/null +++ b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt @@ -0,0 +1,87 @@ +The device node for Mediatek USB3.0 DRD controller + +Required properties: + - compatible : should be "mediatek,mt8173-mtu3" + - reg : specifies physical base address and size of the registers + - reg-names: should be "mac" for device IP and "ippc" for IP port control + - interrupts : interrupt used by the device IP + - power-domains : a phandle to USB power domain node to control USB's + mtcmos + - vusb33-supply : regulator of USB avdd3.3v + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must contain "sys_ck" for clock of controller; + "wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are + depends on "mediatek,enable-wakeup" + - phys : a list of phandle + phy specifier pairs + - dr_mode : should be one of "host", "peripheral" or "otg", + refer to usb/generic.txt + +Optional properties: + - #address-cells, #size-cells : should be '2' if the device has sub-nodes + with 'reg' property + - ranges : allows valid 1:1 translation between child's address space and + parent's address space + - extcon : external connector for vbus and idpin changes detection, needed + when supports dual-role mode. + - vbus-supply : reference to the VBUS regulator, needed when supports + dual-role mode. + - pinctl-names : a pinctrl state named "default" must be defined, + "id_float" and "id_ground" are optinal which depends on + "mediatek,enable-manual-drd" + - pinctrl-0 : pin control group + See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + + - maximum-speed : valid arguments are "super-speed", "high-speed" and + "full-speed"; refer to usb/generic.txt + - enable-manual-drd : supports manual dual-role switch via debugfs; usually + used when receptacle is TYPE-A and also wants to support dual-role + mode. + - mediatek,enable-wakeup : supports ip sleep wakeup used by host mode + - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup + control register, it depends on "mediatek,enable-wakeup". + +Sub-nodes: +The xhci should be added as subnode to mtu3 as shown in the following example +if host mode is enabled. The DT binding details of xhci can be found in: +Documentation/devicetree/bindings/usb/mt8173-xhci.txt + +Example: +ssusb: usb@11271000 { + compatible = "mediatek,mt8173-mtu3"; + reg = <0 0x11271000 0 0x3000>, + <0 0x11280700 0 0x0100>; + reg-names = "mac", "ippc"; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>; + phys = <&phy_port0 PHY_TYPE_USB3>, + <&phy_port1 PHY_TYPE_USB2>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, + <&pericfg CLK_PERI_USB0>, + <&pericfg CLK_PERI_USB1>; + clock-names = "sys_ck", + "wakeup_deb_p0", + "wakeup_deb_p1"; + vusb33-supply = <&mt6397_vusb_reg>; + vbus-supply = <&usb_p0_vbus>; + extcon = <&extcon_usb>; + dr_mode = "otg"; + mediatek,enable-wakeup; + mediatek,syscon-wakeup = <&pericfg>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + usb_host: xhci@11270000 { + compatible = "mediatek,mt8173-xhci"; + reg = <0 0x11270000 0 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>; + clock-names = "sys_ck"; + vusb33-supply = <&mt6397_vusb_reg>; + status = "disabled"; + }; +}; |
