diff options
Diffstat (limited to 'Documentation/devicetree/bindings/sound')
4 files changed, 173 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.txt new file mode 100644 index 000000000000..a4589cda214e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.txt @@ -0,0 +1,67 @@ +NVIDIA Tegra audio complex, with RT5677 CODEC + +Required properties: +- compatible : "nvidia,tegra-audio-rt5677" +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: + - pll_a + - pll_a_out0 + - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the RT5677's pins (as documented in its binding), and the jacks + on the board: + + * Headphone + * Speaker + * Headset Mic + * Internal Mic 1 + * Internal Mic 2 + +- nvidia,i2s-controller : The phandle of the Tegra I2S controller that's + connected to the CODEC. +- nvidia,audio-codec : The phandle of the RT5677 audio codec. This binding + assumes that AIF1 on the CODEC is connected to Tegra. + +Optional properties: +- nvidia,hp-det-gpios : The GPIO that detects headphones are plugged in +- nvidia,hp-en-gpios : The GPIO that enables headphone amplifier +- nvidia,mic-present-gpios: The GPIO that mic jack is plugged in +- nvidia,dmic-clk-en-gpios : The GPIO that gates DMIC clock signal + +Example: + +sound { + compatible = "nvidia,tegra-audio-rt5677-ryu", + "nvidia,tegra-audio-rt5677"; + nvidia,model = "NVIDIA Tegra Ryu"; + + nvidia,audio-routing = + "Headphone", "LOUT2", + "Headphone", "LOUT1", + "Headset Mic", "MICBIAS1", + "IN1P", "Headset Mic", + "IN1N", "Headset Mic", + "DMIC L1", "Internal Mic 1", + "DMIC R1", "Internal Mic 1", + "DMIC L2", "Internal Mic 2", + "DMIC R2", "Internal Mic 2", + "Speaker", "PDM1L", + "Speaker", "PDM1R"; + + nvidia,i2s-controller = <&tegra_i2s1>; + nvidia,audio-codec = <&rt5677>; + + nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>; + nvidia,mic-present-gpios = <&gpio TEGRA_GPIO(O, 5) GPIO_ACTIVE_LOW>; + nvidia,hp-en-gpios = <&rt5677 1 GPIO_ACTIVE_HIGH>; + nvidia,dmic-clk-en-gpios = <&rt5677 2 GPIO_ACTIVE_HIGH>; + + clocks = <&tegra_car TEGRA124_CLK_PLL_A>, + <&tegra_car TEGRA124_CLK_PLL_A_OUT0>, + <&tegra_car TEGRA124_CLK_EXTERN1>; + clock-names = "pll_a", "pll_a_out0", "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index c3cba600bf11..73bf314f7240 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -75,6 +75,11 @@ Optional CPU/CODEC subnodes properties: it can be specified via "clocks" if system has clock node (= common clock), or "system-clock-frequency" (if system doens't support common clock) + If a clock is specified, it is + enabled with clk_prepare_enable() + in dai startup() and disabled with + clk_disable_unprepare() in dai + shutdown(). Example 1 - single DAI link: diff --git a/Documentation/devicetree/bindings/sound/st,sta32x.txt b/Documentation/devicetree/bindings/sound/st,sta32x.txt new file mode 100644 index 000000000000..255de3ae5b2f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/st,sta32x.txt @@ -0,0 +1,92 @@ +STA32X audio CODEC + +The driver for this device only supports I2C. + +Required properties: + + - compatible: "st,sta32x" + - reg: the I2C address of the device for I2C + - reset-gpios: a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + + - power-down-gpios: a GPIO spec for the power down pin. If specified, + it will be deasserted before communication to the codec + starts. + + - Vdda-supply: regulator spec, providing 3.3V + - Vdd3-supply: regulator spec, providing 3.3V + - Vcc-supply: regulator spec, providing 5V - 26V + +Optional properties: + + - st,output-conf: number, Selects the output configuration: + 0: 2-channel (full-bridge) power, 2-channel data-out + 1: 2 (half-bridge). 1 (full-bridge) on-board power + 2: 2 Channel (Full-Bridge) Power, 1 Channel FFX + 3: 1 Channel Mono-Parallel + If parameter is missing, mode 0 will be enabled. + This property has to be specified as '/bits/ 8' value. + + - st,ch1-output-mapping: Channel 1 output mapping + - st,ch2-output-mapping: Channel 2 output mapping + - st,ch3-output-mapping: Channel 3 output mapping + 0: Channel 1 + 1: Channel 2 + 2: Channel 3 + If parameter is missing, channel 1 is chosen. + This properties have to be specified as '/bits/ 8' values. + + - st,thermal-warning-recover: + If present, thermal warning recovery is enabled. + + - st,thermal-warning-adjustment: + If present, thermal warning adjustment is enabled. + + - st,fault-detect-recovery: + If present, then fault recovery will be enabled. + + - st,drop-compensation-ns: number + Only required for "st,ffx-power-output-mode" == + "variable-drop-compensation". + Specifies the drop compensation in nanoseconds. + The value must be in the range of 0..300, and only + multiples of 20 are allowed. Default is 140ns. + + - st,max-power-use-mpcc: + If present, then MPCC bits are used for MPC coefficients, + otherwise standard MPC coefficients are used. + + - st,max-power-corr: + If present, power bridge correction for THD reduction near maximum + power output is enabled. + + - st,am-reduction-mode: + If present, FFX mode runs in AM reduction mode, otherwise normal + FFX mode is used. + + - st,odd-pwm-speed-mode: + If present, PWM speed mode run on odd speed mode (341.3 kHz) on all + channels. If not present, normal PWM spped mode (384 kHz) will be used. + + - st,invalid-input-detect-mute: + If present, automatic invalid input detect mute is enabled. + +Example: + +codec: sta32x@38 { + compatible = "st,sta32x"; + reg = <0x1c>; + reset-gpios = <&gpio1 19 0>; + power-down-gpios = <&gpio1 16 0>; + st,output-conf = /bits/ 8 <0x3>; // set output to 2-channel + // (full-bridge) power, + // 2-channel data-out + st,ch1-output-mapping = /bits/ 8 <0>; // set channel 1 output ch 1 + st,ch2-output-mapping = /bits/ 8 <0>; // set channel 2 output ch 1 + st,ch3-output-mapping = /bits/ 8 <0>; // set channel 3 output ch 1 + st,max-power-correction; // enables power bridge + // correction for THD reduction + // near maximum power output + st,invalid-input-detect-mute; // mute if no valid digital + // audio signal is provided. +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt index 5e6040c2c2e9..47a213c411ce 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt @@ -9,6 +9,7 @@ Required properties: "ti,tlv320aic33" - TLV320AIC33 "ti,tlv320aic3007" - TLV320AIC3007 "ti,tlv320aic3106" - TLV320AIC3106 + "ti,tlv320aic3104" - TLV320AIC3104 - reg - <int> - I2C slave address @@ -18,6 +19,7 @@ Optional properties: - gpio-reset - gpio pin number used for codec reset - ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality + - Not supported on tlv320aic3104 - ai3x-micbias-vg - MicBias Voltage required. 1 - MICBIAS output is powered to 2.0V, 2 - MICBIAS output is powered to 2.5V, @@ -36,7 +38,13 @@ CODEC output pins: * HPLCOM * HPRCOM -CODEC input pins: +CODEC input pins for TLV320AIC3104: + * MIC2L + * MIC2R + * LINE1L + * LINE1R + +CODEC input pins for other compatible codecs: * MIC3L * MIC3R * LINE1L |
