diff options
Diffstat (limited to 'Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt | 163 |
1 files changed, 0 insertions, 163 deletions
diff --git a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt deleted file mode 100644 index 20191315e444..000000000000 --- a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt +++ /dev/null @@ -1,163 +0,0 @@ -* Samsung S5M8767 Voltage and Current Regulator - -The Samsung S5M8767 is a multi-function device which includes voltage and -current regulators, rtc, charger controller and other sub-blocks. It is -interfaced to the host controller using a i2c interface. Each sub-block is -addressed by the host system using different i2c slave address. This document -describes the bindings for 'pmic' sub-block of s5m8767. - -Required properties: -- compatible: Should be "samsung,s5m8767-pmic". -- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. - -- s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) - units for buck2 when changing voltage using gpio dvs. Refer to [1] below - for additional information. - -- s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV) - units for buck3 when changing voltage using gpio dvs. Refer to [1] below - for additional information. - -- s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV) - units for buck4 when changing voltage using gpio dvs. Refer to [1] below - for additional information. - -- s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used - for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines. - -[1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional - property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage' - property should specify atleast one voltage level (which would be a - safe operating voltage). - - If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional - property is specified, then all the eight voltage values for the - 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified. - -Optional properties: -- interrupt-parent: Specifies the phandle of the interrupt controller to which - the interrupts from s5m8767 are delivered to. -- interrupts: Interrupt specifiers for two interrupt sources. - - First interrupt specifier is for 'irq1' interrupt. - - Second interrupt specifier is for 'alert' interrupt. -- s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. -- s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs. -- s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs. - -Additional properties required if either of the optional properties are used: - -- s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from - the possible 8 options selectable by the dvs gpios. The value of this - property should be between 0 and 7. If not specified or if out of range, the - default value of this property is set to 0. - -- s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used - for dvs. The format of the gpio specifier depends in the gpio controller. - -Regulators: The regulators of s5m8767 that have to be instantiated should be -included in a sub-node named 'regulators'. Regulator nodes included in this -sub-node should be of the format as listed below. - - regulator_name { - ldo1_reg: LDO1 { - regulator-name = "VDD_ALIVE_1.0V"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - regulator-boot-on; - op_mode = <1>; /* Normal Mode */ - }; - }; -The above regulator entries are defined in regulator bindings documentation -except these properties: - - op_mode: describes the different operating modes of the LDO's with - power mode change in SOC. The different possible values are, - 0 - always off mode - 1 - on in normal mode - 2 - low power mode - 3 - suspend mode - - s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one - GPIO controlling this regulator (enable/disable); This is - valid only for buck9. - -The following are the names of the regulators that the s5m8767 pmic block -supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number -as per the datasheet of s5m8767. - - - LDOn - - valid values for n are 1 to 28 - - Example: LDO1, LDO2, LDO28 - - BUCKn - - valid values for n are 1 to 9. - - Example: BUCK1, BUCK2, BUCK9 - -The bindings inside the regulator nodes use the standard regulator bindings -which are documented elsewhere. - -Example: - - s5m8767_pmic@66 { - compatible = "samsung,s5m8767-pmic"; - reg = <0x66>; - - s5m8767,pmic-buck2-uses-gpio-dvs; - s5m8767,pmic-buck3-uses-gpio-dvs; - s5m8767,pmic-buck4-uses-gpio-dvs; - - s5m8767,pmic-buck-default-dvs-idx = <0>; - - s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */ - <&gpx0 1 0>, /* DVS2 */ - <&gpx0 2 0>; /* DVS3 */ - - s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */ - <&gpx2 4 0>, /* SET2 */ - <&gpx2 5 0>; /* SET3 */ - - s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, - <1250000>, <1200000>, - <1150000>, <1100000>, - <1000000>, <950000>; - - s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, - <1100000>, <1100000>, - <1000000>, <1000000>, - <1000000>, <1000000>; - - s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, - <1200000>, <1200000>, - <1200000>, <1200000>, - <1200000>, <1200000>; - - regulators { - ldo1_reg: LDO1 { - regulator-name = "VDD_ABB_3.3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - op_mode = <1>; /* Normal Mode */ - }; - - ldo2_reg: LDO2 { - regulator-name = "VDD_ALIVE_1.1V"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - }; - - buck1_reg: BUCK1 { - regulator-name = "VDD_MIF_1.2V"; - regulator-min-microvolt = <950000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-boot-on; - }; - - vemmc_reg: BUCK9 { - regulator-name = "VMEM_VDD_2.8V"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - op_mode = <3>; /* Standby Mode */ - s5m8767,pmic-ext-control-gpios = <&gpk0 2 0>; - }; - }; - }; |
