diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pinctrl')
3 files changed, 320 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt new file mode 100644 index 000000000000..dff0e5f995e2 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -0,0 +1,60 @@ +* Allwinner A1X Pin Controller + +The pins controlled by sunXi pin controller are organized in banks, +each bank has 32 pins. Each pin has 7 multiplexing functions, with +the first two functions being GPIO in and out. The configuration on +the pins includes drive strength and pull-up. + +Required properties: +- compatible: "allwinner,<soc>-pinctrl". Supported SoCs for now are: + sun5i-a13. +- reg: Should contain the register physical address and length for the + pin controller. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices. + +A pinctrl node should contain at least one subnodes representing the +pinctrl groups available on the machine. Each subnode will list the +pins it needs, and how they should be configured, with regard to muxer +configuration, drive strength and pullups. If one of these options is +not set, its actual value will be unspecified. + +Required subnode-properties: + +- allwinner,pins: List of strings containing the pin name. +- allwinner,function: Function to mux the pins listed above to. + +Optional subnode-properties: +- allwinner,drive: Integer. Represents the current sent to the pin + 0: 10 mA + 1: 20 mA + 2: 30 mA + 3: 40 mA +- allwinner,pull: Integer. + 0: No resistor + 1: Pull-up resistor + 2: Pull-down resistor + +Examples: + +pinctrl@01c20800 { + compatible = "allwinner,sun5i-a13-pinctrl"; + reg = <0x01c20800 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + uart1_pins_a: uart1@0 { + allwinner,pins = "PE10", "PE11"; + allwinner,function = "uart1"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + uart1_pins_b: uart1@1 { + allwinner,pins = "PG3", "PG4"; + allwinner,function = "uart1"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra114-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra114-pinmux.txt new file mode 100644 index 000000000000..e204d009f16c --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra114-pinmux.txt @@ -0,0 +1,120 @@ +NVIDIA Tegra114 pinmux controller + +The Tegra114 pinctrl binding is very similar to the Tegra20 and Tegra30 +pinctrl binding, as described in nvidia,tegra20-pinmux.txt and +nvidia,tegra30-pinmux.txt. In fact, this document assumes that binding as +a baseline, and only documents the differences between the two bindings. + +Required properties: +- compatible: "nvidia,tegra114-pinmux" +- reg: Should contain the register physical address and length for each of + the pad control and mux registers. The first bank of address must be the + driver strength pad control register address and second bank address must + be pinmux register address. + +Tegra114 adds the following optional properties for pin configuration subnodes: +- nvidia,enable-input: Integer. Enable the pin's input path. 0: no, 1: yes. +- nvidia,open-drain: Integer. Enable open drain mode. 0: no, 1: yes. +- nvidia,lock: Integer. Lock the pin configuration against further changes + until reset. 0: no, 1: yes. +- nvidia,io-reset: Integer. Reset the IO path. 0: no, 1: yes. +- nvidia,rcv-sel: Integer. Select VIL/VIH receivers. 0: normal, 1: high. +- nvidia,drive-type: Integer. Valid range 0...3. + +As with Tegra20 and Terga30, see the Tegra TRM for complete details regarding +which groups support which functionality. + +Valid values for pin and group names are: + + per-pin mux groups: + + These all support nvidia,function, nvidia,tristate, nvidia,pull, + nvidia,enable-input, nvidia,lock. Some support nvidia,open-drain, + nvidia,io-reset and nvidia,rcv-sel. + + ulpi_data0_po1, ulpi_data1_po2, ulpi_data2_po3, ulpi_data3_po4, + ulpi_data4_po5, ulpi_data5_po6, ulpi_data6_po7, ulpi_data7_po0, + ulpi_clk_py0, ulpi_dir_py1, ulpi_nxt_py2, ulpi_stp_py3, dap3_fs_pp0, + dap3_din_pp1, dap3_dout_pp2, dap3_sclk_pp3, pv0, pv1, sdmmc1_clk_pz0, + sdmmc1_cmd_pz1, sdmmc1_dat3_py4, sdmmc1_dat2_py5, sdmmc1_dat1_py6, + sdmmc1_dat0_py7, clk2_out_pw5, clk2_req_pcc5, hdmi_int_pn7, ddc_scl_pv4, + ddc_sda_pv5, uart2_rxd_pc3, uart2_txd_pc2, uart2_rts_n_pj6, + uart2_cts_n_pj5, uart3_txd_pw6, uart3_rxd_pw7, uart3_cts_n_pa1, + uart3_rts_n_pc0, pu0, pu1, pu2, pu3, pu4, pu5, pu6, gen1_i2c_sda_pc5, + gen1_i2c_scl_pc4, dap4_fs_pp4, dap4_din_pp5, dap4_dout_pp6, dap4_sclk_pp7, + clk3_out_pee0, clk3_req_pee1, gmi_wp_n_pc7, gmi_iordy_pi5, gmi_wait_pi7, + gmi_adv_n_pk0, gmi_clk_pk1, gmi_cs0_n_pj0, gmi_cs1_n_pj2, gmi_cs2_n_pk3, + gmi_cs3_n_pk4, gmi_cs4_n_pk2, gmi_cs6_n_pi3, gmi_cs7_n_pi6, gmi_ad0_pg0, + gmi_ad1_pg1, gmi_ad2_pg2, gmi_ad3_pg3, gmi_ad4_pg4, gmi_ad5_pg5, + gmi_ad6_pg6, gmi_ad7_pg7, gmi_ad8_ph0, gmi_ad9_ph1, gmi_ad10_ph2, + gmi_ad11_ph3, gmi_ad12_ph4, gmi_ad13_ph5, gmi_ad14_ph6, gmi_ad15_ph7, + gmi_a16_pj7, gmi_a17_pb0, gmi_a18_pb1, gmi_a19_pk7, gmi_wr_n_pi0, + gmi_oe_n_pi1, gmi_dqs_p_pj3, gmi_rst_n_pi4, gen2_i2c_scl_pt5, + gen2_i2c_sda_pt6, sdmmc4_clk_pcc4, sdmmc4_cmd_pt7, sdmmc4_dat0_paa0, + sdmmc4_dat1_paa1, sdmmc4_dat2_paa2, sdmmc4_dat3_paa3, sdmmc4_dat4_paa4, + sdmmc4_dat5_paa5, sdmmc4_dat6_paa6, sdmmc4_dat7_paa7, cam_mclk_pcc0, + pcc1, pbb0, cam_i2c_scl_pbb1, cam_i2c_sda_pbb2, pbb3, pbb4, pbb5, pbb6, + pbb7, pcc2, pwr_i2c_scl_pz6, pwr_i2c_sda_pz7, kb_row0_pr0, kb_row1_pr1, + kb_row2_pr2, kb_row3_pr3, kb_row4_pr4, kb_row5_pr5, kb_row6_pr6, + kb_row7_pr7, kb_row8_ps0, kb_row9_ps1, kb_row10_ps2, kb_col0_pq0, + kb_col1_pq1, kb_col2_pq2, kb_col3_pq3, kb_col4_pq4, kb_col5_pq5, + kb_col6_pq6, kb_col7_pq7, clk_32k_out_pa0, sys_clk_req_pz5, core_pwr_req, + cpu_pwr_req, pwr_int_n, owr, dap1_fs_pn0, dap1_din_pn1, dap1_dout_pn2, + dap1_sclk_pn3, clk1_req_pee2, clk1_out_pw4, spdif_in_pk6, spdif_out_pk5, + dap2_fs_pa2, dap2_din_pa4, dap2_dout_pa5, dap2_sclk_pa3, dvfs_pwm_px0, + gpio_x1_aud_px1, gpio_x3_aud_px3, dvfs_clk_px2, gpio_x4_aud_px4, + gpio_x5_aud_px5, gpio_x6_aud_px6, gpio_x7_aud_px7, sdmmc3_clk_pa6, + sdmmc3_cmd_pa7, sdmmc3_dat0_pb7, sdmmc3_dat1_pb6, sdmmc3_dat2_pb5, + sdmmc3_dat3_pb4, hdmi_cec_pee3, sdmmc1_wp_n_pv3, sdmmc3_cd_n_pv2, + gpio_w2_aud_pw2, gpio_w3_aud_pw3, usb_vbus_en0_pn4, usb_vbus_en1_pn5, + sdmmc3_clk_lb_in_pee5, sdmmc3_clk_lb_out_pee4, reset_out_n. + + drive groups: + + These all support nvidia,pull-down-strength, nvidia,pull-up-strength, + nvidia,slew-rate-rising, nvidia,slew-rate-falling. Most but not all + support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode + and nvidia,drive-type. + + ao1, ao2, at1, at2, at3, at4, at5, cdev1, cdev2, dap1, dap2, dap3, dap4, + dbg, sdio3, spi, uaa, uab, uart2, uart3, sdio1, ddc, gma, gme, gmf, gmg, + gmh, owr, uda. + +Example: + + pinmux: pinmux { + compatible = "nvidia,tegra114-pinmux"; + reg = <0x70000868 0x148 /* Pad control registers */ + 0x70003000 0x40c>; /* PinMux registers */ + }; + +Example board file extract: + + pinctrl { + sdmmc4_default: pinmux { + sdmmc4_clk_pcc4 { + nvidia,pins = "sdmmc4_clk_pcc4", + nvidia,function = "sdmmc4"; + nvidia,pull = <0>; + nvidia,tristate = <0>; + }; + sdmmc4_dat0_paa0 { + nvidia,pins = "sdmmc4_dat0_paa0", + "sdmmc4_dat1_paa1", + "sdmmc4_dat2_paa2", + "sdmmc4_dat3_paa3", + "sdmmc4_dat4_paa4", + "sdmmc4_dat5_paa5", + "sdmmc4_dat6_paa6", + "sdmmc4_dat7_paa7"; + nvidia,function = "sdmmc4"; + nvidia,pull = <2>; + nvidia,tristate = <0>; + }; + }; + }; + + sdhci@78000400 { + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc4_default>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt b/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt new file mode 100644 index 000000000000..9a2f3f420526 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt @@ -0,0 +1,140 @@ +ST Ericsson Nomadik pinmux controller + +Required properties: +- compatible: "stericsson,nmk-pinctrl", "stericsson,nmk-pinctrl-db8540", + "stericsson,nmk-pinctrl-stn8815" +- reg: Should contain the register physical address and length of the PRCMU. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +ST Ericsson's pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as input, output, pull up, pull down... + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Required subnode-properties: +- ste,pins : An array of strings. Each string contains the name of a pin or + group. + +Optional subnode-properties: +- ste,function: A string containing the name of the function to mux to the + pin or group. + +- ste,config: Handle of pin configuration node (e.g. ste,config = <&slpm_in_wkup_pdis>) + +- ste,input : <0/1/2> + 0: input with no pull + 1: input with pull up, + 2: input with pull down, + +- ste,output: <0/1/2> + 0: output low, + 1: output high, + 2: output (value is not specified). + +- ste,sleep: <0/1> + 0: sleep mode disable, + 1: sleep mode enable. + +- ste,sleep-input: <0/1/2/3> + 0: sleep input with no pull, + 1: sleep input with pull up, + 2: sleep input with pull down. + 3: sleep input and keep last input configuration (no pull, pull up or pull down). + +- ste,sleep-output: <0/1/2> + 0: sleep output low, + 1: sleep output high, + 2: sleep output (value is not specified). + +- ste,sleep-gpio: <0/1> + 0: disable sleep gpio mode, + 1: enable sleep gpio mode. + +- ste,sleep-wakeup: <0/1> + 0: wake-up detection enabled, + 1: wake-up detection disabled. + +- ste,sleep-pull-disable: <0/1> + 0: GPIO pull-up or pull-down resistor is enabled, when pin is an input, + 1: GPIO pull-up and pull-down resistor are disabled. + +Example board file extract: + + pinctrl@80157000 { + compatible = "stericsson,nmk-pinctrl"; + reg = <0x80157000 0x2000>; + + pinctrl-names = "default"; + + slpm_in_wkup_pdis: slpm_in_wkup_pdis { + ste,sleep = <1>; + ste,sleep-input = <3>; + ste,sleep-wakeup = <1>; + ste,sleep-pull-disable = <0>; + }; + + slpm_out_hi_wkup_pdis: slpm_out_hi_wkup_pdis { + ste,sleep = <1>; + ste,sleep-output = <1>; + ste,sleep-wakeup = <1>; + ste,sleep-pull-disable = <0>; + }; + + slpm_out_wkup_pdis: slpm_out_wkup_pdis { + ste,sleep = <1>; + ste,sleep-output = <2>; + ste,sleep-wakeup = <1>; + ste,sleep-pull-disable = <0>; + }; + + uart0 { + uart0_default_mux: uart0_mux { + u0_default_mux { + ste,function = "u0"; + ste,pins = "u0_a_1"; + }; + }; + uart0_default_mode: uart0_default { + uart0_default_cfg1 { + ste,pins = "GPIO0", "GPIO2"; + ste,input = <1>; + }; + + uart0_default_cfg2 { + ste,pins = "GPIO1", "GPIO3"; + ste,output = <1>; + }; + }; + uart0_sleep_mode: uart0_sleep { + uart0_sleep_cfg1 { + ste,pins = "GPIO0", "GPIO2"; + ste,config = <&slpm_in_wkup_pdis>; + }; + uart0_sleep_cfg2 { + ste,pins = "GPIO1"; + ste,config = <&slpm_out_hi_wkup_pdis>; + }; + uart0_sleep_cfg3 { + ste,pins = "GPIO3"; + ste,config = <&slpm_out_wkup_pdis>; + }; + }; + }; + }; + + uart@80120000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x80120000 0x1000>; + interrupts = <0 11 0x4>; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&uart0_default_mux>, <&uart0_default_mode>; + pinctrl-1 = <&uart0_sleep_mode>; + }; |
