diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio')
3 files changed, 222 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/iio/adc/at91_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt new file mode 100644 index 000000000000..0f813dec5e08 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt @@ -0,0 +1,87 @@ +* AT91's Analog to Digital Converter (ADC) + +Required properties: + - compatible: Should be "atmel,<chip>-adc" + <chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5" + - reg: Should contain ADC registers location and length + - interrupts: Should contain the IRQ line for the ADC + - clock-names: tuple listing input clock names. + Required elements: "adc_clk", "adc_op_clk". + - clocks: phandles to input clocks. + - atmel,adc-channels-used: Bitmask of the channels muxed and enabled for this + device + - atmel,adc-startup-time: Startup Time of the ADC in microseconds as + defined in the datasheet + - atmel,adc-vref: Reference voltage in millivolts for the conversions + - atmel,adc-res: List of resolutions in bits supported by the ADC. List size + must be two at least. + - atmel,adc-res-names: Contains one identifier string for each resolution + in atmel,adc-res property. "lowres" and "highres" + identifiers are required. + +Optional properties: + - atmel,adc-use-external-triggers: Boolean to enable the external triggers + - atmel,adc-use-res: String corresponding to an identifier from + atmel,adc-res-names property. If not specified, the highest + resolution will be used. + - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion + - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds + - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this + value is set, then the adc driver will enable touchscreen + support. + NOTE: when adc touchscreen is enabled, the adc hardware trigger will be + disabled. Since touchscreen will occupy the trigger register. + - atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It + makes touch detection more precise. + +Optional trigger Nodes: + - Required properties: + * trigger-name: Name of the trigger exposed to the user + * trigger-value: Value to put in the Trigger register + to activate this trigger + - Optional properties: + * trigger-external: Is the trigger an external trigger? + +Examples: +adc0: adc@fffb0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91sam9260-adc"; + reg = <0xfffb0000 0x100>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&adc_clk>, <&adc_op_clk>; + clock-names = "adc_clk", "adc_op_clk"; + atmel,adc-channels-used = <0xff>; + atmel,adc-startup-time = <40>; + atmel,adc-use-external-triggers; + atmel,adc-vref = <3300>; + atmel,adc-res = <8 10>; + atmel,adc-res-names = "lowres", "highres"; + atmel,adc-use-res = "lowres"; + + trigger@0 { + reg = <0>; + trigger-name = "external-rising"; + trigger-value = <0x1>; + trigger-external; + }; + trigger@1 { + reg = <1>; + trigger-name = "external-falling"; + trigger-value = <0x2>; + trigger-external; + }; + + trigger@2 { + reg = <2>; + trigger-name = "external-any"; + trigger-value = <0x3>; + trigger-external; + }; + + trigger@3 { + reg = <3>; + trigger-name = "continuous"; + trigger-value = <0x6>; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt new file mode 100644 index 000000000000..dcebff1928e1 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt @@ -0,0 +1,22 @@ +Freescale vf610 Analog to Digital Converter bindings + +The devicetree bindings are for the new ADC driver written for +vf610/i.MX6slx and upward SoCs from Freescale. + +Required properties: +- compatible: Should contain "fsl,vf610-adc" +- reg: Offset and length of the register set for the device +- interrupts: Should contain the interrupt for the device +- clocks: The clock is needed by the ADC controller, ADC clock source is ipg clock. +- clock-names: Must contain "adc", matching entry in the clocks property. +- vref-supply: The regulator supply ADC refrence voltage. + +Example: +adc0: adc@4003b000 { + compatible = "fsl,vf610-adc"; + reg = <0x4003b000 0x1000>; + interrupts = <0 53 0x04>; + clocks = <&clks VF610_CLK_ADC0>; + clock-names = "adc"; + vref-supply = <®_vcc_3v3_mcu>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt b/Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt new file mode 100644 index 000000000000..d9ee909d2b78 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt @@ -0,0 +1,113 @@ +Xilinx XADC device driver + +This binding document describes the bindings for both of them since the +bindings are very similar. The Xilinx XADC is a ADC that can be found in the +series 7 FPGAs from Xilinx. The XADC has a DRP interface for communication. +Currently two different frontends for the DRP interface exist. One that is only +available on the ZYNQ family as a hardmacro in the SoC portion of the ZYNQ. The +other one is available on all series 7 platforms and is a softmacro with a AXI +interface. This binding document describes the bindings for both of them since +the bindings are very similar. + +Required properties: + - compatible: Should be one of + * "xlnx,zynq-xadc-1.00.a": When using the ZYNQ device + configuration interface to interface to the XADC hardmacro. + * "xlnx,axi-xadc-1.00.a": When using the axi-xadc pcore to + interface to the XADC hardmacro. + - reg: Address and length of the register set for the device + - interrupts: Interrupt for the XADC control interface. + - clocks: When using the ZYNQ this must be the ZYNQ PCAP clock, + when using the AXI-XADC pcore this must be the clock that provides the + clock to the AXI bus interface of the core. + +Optional properties: + - interrupt-parent: phandle to the parent interrupt controller + - xlnx,external-mux: + * "none": No external multiplexer is used, this is the default + if the property is omitted. + * "single": External multiplexer mode is used with one + multiplexer. + * "dual": External multiplexer mode is used with two + multiplexers for simultaneous sampling. + - xlnx,external-mux-channel: Configures which pair of pins is used to + sample data in external mux mode. + Valid values for single external multiplexer mode are: + 0: VP/VN + 1: VAUXP[0]/VAUXN[0] + 2: VAUXP[1]/VAUXN[1] + ... + 16: VAUXP[15]/VAUXN[15] + Valid values for dual external multiplexer mode are: + 1: VAUXP[0]/VAUXN[0] - VAUXP[8]/VAUXN[8] + 2: VAUXP[1]/VAUXN[1] - VAUXP[9]/VAUXN[9] + ... + 8: VAUXP[7]/VAUXN[7] - VAUXP[15]/VAUXN[15] + + This property needs to be present if the device is configured for + external multiplexer mode (either single or dual). If the device is + not using external multiplexer mode the property is ignored. + - xnlx,channels: List of external channels that are connected to the ADC + Required properties: + * #address-cells: Should be 1. + * #size-cells: Should be 0. + + The child nodes of this node represent the external channels which are + connected to the ADC. If the property is no present no external + channels will be assumed to be connected. + + Each child node represents one channel and has the following + properties: + Required properties: + * reg: Pair of pins the the channel is connected to. + 0: VP/VN + 1: VAUXP[0]/VAUXN[0] + 2: VAUXP[1]/VAUXN[1] + ... + 16: VAUXP[15]/VAUXN[15] + Note each channel number should only be used at most + once. + Optional properties: + * xlnx,bipolar: If set the channel is used in bipolar + mode. + + +Examples: + xadc@f8007100 { + compatible = "xlnx,zynq-xadc-1.00.a"; + reg = <0xf8007100 0x20>; + interrupts = <0 7 4>; + interrupt-parent = <&gic>; + clocks = <&pcap_clk>; + + xlnx,channels { + #address-cells = <1>; + #size-cells = <0>; + channel@0 { + reg = <0>; + }; + channel@1 { + reg = <1>; + }; + channel@8 { + reg = <8>; + }; + }; + }; + + xadc@43200000 { + compatible = "xlnx,axi-xadc-1.00.a"; + reg = <0x43200000 0x1000>; + interrupts = <0 53 4>; + interrupt-parent = <&gic>; + clocks = <&fpga1_clk>; + + xlnx,channels { + #address-cells = <1>; + #size-cells = <0>; + channel@0 { + reg = <0>; + xlnx,bipolar; + }; + }; + }; |
