diff options
Diffstat (limited to 'Documentation/devicetree/bindings/i2c')
4 files changed, 86 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/i2c/gpio-i2c.txt b/Documentation/devicetree/bindings/i2c/gpio-i2c.txt new file mode 100644 index 000000000000..4f8ec947c6bd --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/gpio-i2c.txt @@ -0,0 +1,32 @@ +Device-Tree bindings for i2c gpio driver + +Required properties: + - compatible = "i2c-gpio"; + - gpios: sda and scl gpio + + +Optional properties: + - i2c-gpio,sda-open-drain: sda as open drain + - i2c-gpio,scl-open-drain: scl as open drain + - i2c-gpio,scl-output-only: scl as output only + - i2c-gpio,delay-us: delay between GPIO operations (may depend on each platform) + - i2c-gpio,timeout-ms: timeout to get data + +Example nodes: + +i2c@0 { + compatible = "i2c-gpio"; + gpios = <&pioA 23 0 /* sda */ + &pioA 24 0 /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + + rv3029c2@56 { + compatible = "rv3029c2"; + reg = <0x56>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt index 1bfc02de1b0c..30ac3a0557f7 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt @@ -4,6 +4,8 @@ Required properties: - compatible: Should be "fsl,<chip>-i2c" - reg: Should contain registers location and length - interrupts: Should contain ERROR and DMA interrupts +- clock-frequency: Desired I2C bus clock frequency in Hz. + Only 100000Hz and 400000Hz modes are supported. Examples: @@ -13,4 +15,5 @@ i2c0: i2c@80058000 { compatible = "fsl,imx28-i2c"; reg = <0x80058000 2000>; interrupts = <111 68>; + clock-frequency = <100000>; }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt new file mode 100644 index 000000000000..c15781f4dc8c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt @@ -0,0 +1,33 @@ +Device tree configuration for i2c-ocores + +Required properties: +- compatible : "opencores,i2c-ocores" +- reg : bus address start and address range size of device +- interrupts : interrupt number +- clock-frequency : frequency of bus clock in Hz +- #address-cells : should be <1> +- #size-cells : should be <0> + +Optional properties: +- reg-shift : device register offsets are shifted by this value +- reg-io-width : io register width in bytes (1, 2 or 4) +- regstep : deprecated, use reg-shift above + +Example: + + i2c0: ocores@a0000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "opencores,i2c-ocores"; + reg = <0xa0000000 0x8>; + interrupts = <10>; + clock-frequency = <20000000>; + + reg-shift = <0>; /* 8 bit registers */ + reg-io-width = <1>; /* 8 bit read/write */ + + dummy@60 { + compatible = "dummy"; + reg = <0x60>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt b/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt index b891ee218354..0f7945019f6f 100644 --- a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt @@ -1,4 +1,4 @@ -* I2C +* Marvell MMP I2C controller Required properties : @@ -32,3 +32,20 @@ Examples: interrupts = <58>; }; +* Marvell MV64XXX I2C controller + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : Should be "marvell,mv64xxx-i2c" + - interrupts : The interrupt number + - clock-frequency : Desired I2C bus clock frequency in Hz. + +Examples: + + i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + interrupts = <29>; + clock-frequency = <100000>; + }; |
