diff options
62 files changed, 7809 insertions, 304 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index 1ccc8a515b44..27b457c09729 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -1440,6 +1440,258 @@ platforms are moved over to use the flattened-device-tree model. descriptor-types-mask = <012b0ebf>; }; + h) Board Control and Status (BCSR) + + Required properties: + + - device_type : Should be "board-control" + - reg : Offset and length of the register set for the device + + Example: + + bcsr@f8000000 { + device_type = "board-control"; + reg = <f8000000 8000>; + }; + + i) Freescale QUICC Engine module (QE) + This represents qe module that is installed on PowerQUICC II Pro. + Hopefully it will merge backward compatibility with CPM/CPM2. + Basically, it is a bus of devices, that could act more or less + as a complete entity (UCC, USB etc ). All of them should be siblings on + the "root" qe node, using the common properties from there. + The description below applies to the the qe of MPC8360 and + more nodes and properties would be extended in the future. + + i) Root QE device + + Required properties: + - device_type : should be "qe"; + - model : precise model of the QE, Can be "QE", "CPM", or "CPM2" + - reg : offset and length of the device registers. + - bus-frequency : the clock frequency for QUICC Engine. + + Recommended properties + - brg-frequency : the internal clock source frequency for baud-rate + generators in Hz. + + Example: + qe@e0100000 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + device_type = "qe"; + model = "QE"; + ranges = <0 e0100000 00100000>; + reg = <e0100000 480>; + brg-frequency = <0>; + bus-frequency = <179A7B00>; + } + + + ii) SPI (Serial Peripheral Interface) + + Required properties: + - device_type : should be "spi". + - compatible : should be "fsl_spi". + - mode : the spi operation mode, it can be "cpu" or "qe". + - reg : Offset and length of the register set for the device + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + + Example: + spi@4c0 { + device_type = "spi"; + compatible = "fsl_spi"; + reg = <4c0 40>; + interrupts = <82 0>; + interrupt-parent = <700>; + mode = "cpu"; + }; + + + iii) USB (Universal Serial Bus Controller) + + Required properties: + - device_type : should be "usb". + - compatible : could be "qe_udc" or "fhci-hcd". + - mode : the could be "host" or "slave". + - reg : Offset and length of the register set for the device + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + + Example(slave): + usb@6c0 { + device_type = "usb"; + compatible = "qe_udc"; + reg = <6c0 40>; + interrupts = <8b 0>; + interrupt-parent = <700>; + mode = "slave"; + }; + + + iv) UCC (Unified Communications Controllers) + + Required properties: + - device_type : should be "network", "hldc", "uart", "transparent" + "bisync" or "atm". + - compatible : could be "ucc_geth" or "fsl_atm" and so on. + - model : should be "UCC". + - device-id : the ucc number(1-8), corresponding to UCCx in UM. + - reg : Offset and length of the register set for the device + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - pio-handle : The phandle for the Parallel I/O port configuration. + - rx-clock : represents the UCC receive clock source. + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. + - tx-clock: represents the UCC transmit clock source; + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. + + Required properties for network device_type: + - mac-address : list of bytes representing the ethernet address. + - phy-handle : The phandle for the PHY connected to this controller. + + Example: + ucc@2000 { + device_type = "network"; + compatible = "ucc_geth"; + model = "UCC"; + device-id = <1>; + reg = <2000 200>; + interrupts = <a0 0>; + interrupt-parent = <700>; + mac-address = [ 00 04 9f 00 23 23 ]; + rx-clock = "none"; + tx-clock = "clk9"; + phy-handle = <212000>; + pio-handle = <140001>; + }; + + + v) Parallel I/O Ports + + This node configures Parallel I/O ports for CPUs with QE support. + The node should reside in the "soc" node of the tree. For each + device that using parallel I/O ports, a child node should be created. + See the definition of the Pin configuration nodes below for more + information. + + Required properties: + - device_type : should be "par_io". + - reg : offset to the register set and its length. + - num-ports : number of Parallel I/O ports + + Example: + par_io@1400 { + reg = <1400 100>; + #address-cells = <1>; + #size-cells = <0>; + device_type = "par_io"; + num-ports = <7>; + ucc_pin@01 { + ...... + }; + + + vi) Pin configuration nodes + + Required properties: + - linux,phandle : phandle of this node; likely referenced by a QE + device. + - pio-map : array of pin configurations. Each pin is defined by 6 + integers. The six numbers are respectively: port, pin, dir, + open_drain, assignment, has_irq. + - port : port number of the pin; 0-6 represent port A-G in UM. + - pin : pin number in the port. + - dir : direction of the pin, should encode as follows: + + 0 = The pin is disabled + 1 = The pin is an output + 2 = The pin is an input + 3 = The pin is I/O + + - open_drain : indicates the pin is normal or wired-OR: + + 0 = The pin is actively driven as an output + 1 = The pin is an open-drain driver. As an output, the pin is + driven active-low, otherwise it is three-stated. + + - assignment : function number of the pin according to the Pin Assignment + tables in User Manual. Each pin can have up to 4 possible functions in + QE and two options for CPM. + - has_irq : indicates if the pin is used as source of exteral + interrupts. + + Example: + ucc_pin@01 { + linux,phandle = <140001>; + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 3 1 0 1 0 /* TxD0 */ + 0 4 1 0 1 0 /* TxD1 */ + 0 5 1 0 1 0 /* TxD2 */ + 0 6 1 0 1 0 /* TxD3 */ + 1 6 1 0 3 0 /* TxD4 */ + 1 7 1 0 1 0 /* TxD5 */ + 1 9 1 0 2 0 /* TxD6 */ + 1 a 1 0 2 0 /* TxD7 */ + 0 9 2 0 1 0 /* RxD0 */ + 0 a 2 0 1 0 /* RxD1 */ + 0 b 2 0 1 0 /* RxD2 */ + 0 c 2 0 1 0 /* RxD3 */ + 0 d 2 0 1 0 /* RxD4 */ + 1 1 2 0 2 0 /* RxD5 */ + 1 0 2 0 2 0 /* RxD6 */ + 1 4 2 0 2 0 /* RxD7 */ + 0 7 1 0 1 0 /* TX_EN */ + 0 8 1 0 1 0 /* TX_ER */ + 0 f 2 0 1 0 /* RX_DV */ + 0 10 2 0 1 0 /* RX_ER */ + 0 0 2 0 1 0 /* RX_CLK */ + 2 9 1 0 3 0 /* GTX_CLK - CLK10 */ + 2 8 2 0 1 0>; /* GTX125 - CLK9 */ + }; + + vii) Multi-User RAM (MURAM) + + Required properties: + - device_type : should be "muram". + - mode : the could be "host" or "slave". + - ranges : Should be defined as specified in 1) to describe the + translation of MURAM addresses. + - data-only : sub-node which defines the address area under MURAM + bus that can be allocated as data/parameter + + Example: + + muram@10000 { + device_type = "muram"; + ranges = <0 00010000 0000c000>; + + data-only@0{ + reg = <0 c000>; + }; + }; More devices will be defined as this spec matures. diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig index 96ef656e4669..8b6910465578 100644 --- a/arch/powerpc/Kconfig +++ b/arch/powerpc/Kconfig @@ -338,10 +338,6 @@ config PPC_MULTIPLATFORM RS/6000 machine, an Apple machine, or a PReP, CHRP, Maple or Cell-based machine. -config PPC_ISERIES - bool "IBM Legacy iSeries" - depends on PPC64 - config EMBEDDED6xx bool "Embedded 6xx/7xx/7xxx-based board" depends on PPC32 && (BROKEN||BROKEN_ON_SMP) @@ -355,6 +351,16 @@ config APUS <http://linux-apus.sourceforge.net/>. endchoice +config QUICC_ENGINE + bool + depends on PPC_MPC836x || PPC_MPC832x + default y + help + The QUICC Engine (QE) is a new generation of communications + coprocessors on Freescale embedded CPUs (akin to CPM in older chips). + Selecting this option means that you wish to build a kernel + for a machine with a QE coprocessor. + config PPC_PSERIES depends on PPC_MULTIPLATFORM && PPC64 bool "IBM pSeries & new (POWER5-based) iSeries" @@ -365,6 +371,10 @@ config PPC_PSERIES select PPC_UDBG_16550 default y +config PPC_ISERIES + bool "IBM Legacy iSeries" + depends on PPC_MULTIPLATFORM && PPC64 + config PPC_CHRP bool "Common Hardware Reference Platform (CHRP) based machines" depends on PPC_MULTIPLATFORM && PPC32 @@ -594,6 +604,7 @@ endmenu source arch/powerpc/platforms/embedded6xx/Kconfig source arch/powerpc/platforms/4xx/Kconfig +source arch/powerpc/platforms/82xx/Kconfig source arch/powerpc/platforms/83xx/Kconfig source arch/powerpc/platforms/85xx/Kconfig source arch/powerpc/platforms/86xx/Kconfig @@ -1058,6 +1069,8 @@ source "fs/Kconfig" # XXX source "arch/ppc/8260_io/Kconfig" +source "arch/powerpc/sysdev/qe_lib/Kconfig" + source "arch/powerpc/platforms/iseries/Kconfig" source "lib/Kconfig" diff --git a/arch/powerpc/boot/dts/mpc8272ads.dts b/arch/powerpc/boot/dts/mpc8272ads.dts new file mode 100644 index 000000000000..34efdd028c4f --- /dev/null +++ b/arch/powerpc/boot/dts/mpc8272ads.dts @@ -0,0 +1,223 @@ +/* + * MPC8272 ADS Device Tree Source + * + * Copyright 2005 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +/ { + model = "MPC8272ADS"; + compatible = "MPC8260ADS"; + #address-cells = <1>; + #size-cells = <1>; + linux,phandle = <100>; + + cpus { + #cpus = <1>; + #address-cells = <1>; + #size-cells = <0>; + linux,phandle = <200>; + + PowerPC,8272@0 { + device_type = "cpu"; + reg = <0>; + d-cache-line-size = <20>; // 32 bytes + i-cache-line-size = <20>; // 32 bytes + d-cache-size = <4000>; // L1, 16K + i-cache-size = <4000>; // L1, 16K + timebase-frequency = <0>; + bus-frequency = <0>; + clock-frequency = <0>; + 32-bit; + linux,phandle = <201>; + linux,boot-cpu; + }; + }; + + interrupt-controller@f8200000 { + linux,phandle = <f8200000>; + #address-cells = <0>; + #interrupt-cells = <2>; + interrupt-controller; + reg = <f8200000 f8200004>; + built-in; + device_type = "pci-pic"; + }; + memory { + device_type = "memory"; + linux,phandle = <300>; + reg = <00000000 4000000 f4500000 00000020>; + }; + + soc8272@f0000000 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + device_type = "soc"; + ranges = < 0 0 2 00000000 f0000000 00053000>; + reg = <f0000000 0>; + + mdio@0 { + device_type = "mdio"; + compatible = "fs_enet"; + reg = <0 0>; + linux,phandle = <24520>; + #address-cells = <1>; + #size-cells = <0>; + ethernet-phy@0 { + linux,phandle = <2452000>; + interrupt-parent = <10c00>; + interrupts = <19 1>; + reg = <0>; + bitbang = [ 12 12 13 02 02 01 ]; + device_type = "ethernet-phy"; + }; + ethernet-phy@1 { + linux,phandle = <2452001>; + interrupt-parent = <10c00>; + interrupts = <19 1>; + bitbang = [ 12 12 13 02 02 01 ]; + reg = <3>; + device_type = "ethernet-phy"; + }; + }; + + ethernet@24000 { + #address-cells = <1>; + #size-cells = <0>; + device_type = "network"; + device-id = <2>; + compatible = "fs_enet"; + model = "FCC"; + reg = <11300 20 8400 100 11380 30>; + mac-address = [ 00 11 2F 99 43 54 ]; + interrupts = <20 2>; + interrupt-parent = <10c00>; + phy-handle = <2452000>; + rx-clock = <13>; + tx-clock = <12>; + }; + + ethernet@25000 { + device_type = "network"; + device-id = <3>; + compatible = "fs_enet"; + model = "FCC"; + reg = <11320 20 8500 100 113b0 30>; + mac-address = [ 00 11 2F 99 44 54 ]; + interrupts = <21 2>; + interrupt-parent = <10c00>; + phy-handle = <2452001>; + rx-clock = <17>; + tx-clock = <18>; + }; + + cpm@f0000000 { + linux,phandle = <f0000000>; + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + device_type = "cpm"; + model = "CPM2"; + ranges = <00000000 00000000 3ffff>; + reg = <10d80 3280>; + command-proc = <119c0>; + brg-frequency = <17D7840>; + cpm_clk = <BEBC200>; + + scc@11a00 { + device_type = "serial"; + compatible = "cpm_uart"; + model = "SCC"; + device-id = <2>; + reg = <11a00 20 8000 100>; + current-speed = <1c200>; + interrupts = <28 2>; + interrupt-parent = <10c00>; + clock-setup = <0 00ffffff>; + rx-clock = <1>; + tx-clock = <1>; + }; + + scc@11a60 { + device_type = "serial"; + compatible = "cpm_uart"; + model = "SCC"; + device-id = <5>; + reg = <11a60 20 8300 100>; + current-speed = <1c200>; + interrupts = <2b 2>; + interrupt-parent = <10c00>; + clock-setup = <1b ffffff00>; + rx-clock = <4>; + tx-clock = <4>; + }; + + }; + interrupt-controller@10c00 { + linux,phandle = <10c00>; + #address-cells = <0>; + #interrupt-cells = <2>; + interrupt-controller; + reg = <10c00 80>; + built-in; + device_type = "cpm-pic"; + compatible = "CPM2"; + }; + pci@0500 { + linux,phandle = <0500>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "8272"; + device_type = "pci"; + reg = <10430 4dc>; + clock-frequency = <3f940aa>; + interrupt-map-mask = <f800 0 0 7>; + interrupt-map = < + + /* IDSEL 0x16 */ + b000 0 0 1 f8200000 40 0 + b000 0 0 2 f8200000 41 0 + b000 0 0 3 f8200000 42 0 + b000 0 0 4 f8200000 43 0 + + /* IDSEL 0x17 */ + b800 0 0 1 f8200000 43 0 + b800 0 0 2 f8200000 40 0 + b800 0 0 3 f8200000 41 0 + b800 0 0 4 f8200000 42 0 + + /* IDSEL 0x18 */ + c000 0 0 1 f8200000 42 0 + c000 0 0 2 f8200000 43 0 + c000 0 0 3 f8200000 40 0 + c000 0 0 4 f8200000 41 0>; + interrupt-parent = <10c00>; + interrupts = <14 3>; + bus-range = <0 0>; + ranges = <02000000 0 80000000 80000000 0 40000000 + 01000000 0 00000000 f6000000 0 02000000>; + }; + +/* May need to remove if on a part without crypto engine */ + crypto@30000 { + device_type = "crypto"; + model = "SEC2"; + compatible = "talitos"; + reg = <30000 10000>; + interrupts = <b 0>; + interrupt-parent = <10c00>; + num-channels = <4>; + channel-fifo-len = <18>; + exec-units-mask = <0000007e>; +/* desc mask is for rev1.x, we need runtime fixup for >=2.x */ + descriptor-types-mask = <01010ebf>; + }; + + }; +}; diff --git a/arch/powerpc/boot/dts/mpc8360emds.dts b/arch/powerpc/boot/dts/mpc8360emds.dts new file mode 100644 index 000000000000..9022192155b9 --- /dev/null +++ b/arch/powerpc/boot/dts/mpc8360emds.dts @@ -0,0 +1,375 @@ +/* + * MPC8360E EMDS Device Tree Source + * + * Copyright 2006 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + + +/* +/memreserve/ 00000000 1000000; +*/ + +/ { + model = "MPC8360EPB"; + compatible = "MPC83xx"; + #address-cells = <1>; + #size-cells = <1>; + linux,phandle = <100>; + + cpus { + #cpus = <1>; + #address-cells = <1>; + #size-cells = <0>; + linux,phandle = <200>; + + PowerPC,8360@0 { + device_type = "cpu"; + reg = <0>; + d-cache-line-size = <20>; // 32 bytes + i-cache-line-size = <20>; // 32 bytes + d-cache-size = <8000>; // L1, 32K + i-cache-size = <8000>; // L1, 32K + timebase-frequency = <3EF1480>; + bus-frequency = <FBC5200>; + clock-frequency = <1F78A400>; + 32-bit; + linux,phandle = <201>; + linux,boot-cpu; + }; + }; + + memory { + device_type = "memory"; + linux,phandle = <300>; + reg = <00000000 10000000>; + }; + + bcsr@f8000000 { + device_type = "board-control"; + reg = <f8000000 8000>; + }; + + soc8360@e0000000 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + device_type = "soc"; + ranges = <0 e0000000 00100000>; + reg = <e0000000 00000200>; + bus-frequency = <FBC5200>; + + wdt@200 { + device_type = "watchdog"; + compatible = "mpc83xx_wdt"; + reg = <200 100>; + }; + + i2c@3000 { + device_type = "i2c"; + compatible = "fsl-i2c"; + reg = <3000 100>; + interrupts = <e 8>; + interrupt-parent = <700>; + dfsrr; + }; + + i2c@3100 { + device_type = "i2c"; + compatible = "fsl-i2c"; + reg = <3100 100>; + interrupts = <f 8>; + interrupt-parent = <700>; + dfsrr; + }; + + serial@4500 { + device_type = "serial"; + compatible = "ns16550"; + reg = <4500 100>; + clock-frequency = <FBC5200>; + interrupts = <9 8>; + interrupt-parent = <700>; + }; + + serial@4600 { + device_type = "serial"; + compatible = "ns16550"; + reg = <4600 100>; + clock-frequency = <FBC5200>; + interrupts = <a 8>; + interrupt-parent = <700>; + }; + + crypto@30000 { + device_type = "crypto"; + model = "SEC2"; + compatible = "talitos"; + reg = <30000 10000>; + interrupts = <b 8>; + interrupt-parent = <700>; + num-channels = <4>; + channel-fifo-len = <18>; + exec-units-mask = <0000007e>; + /* desc mask is for rev1.x, we need runtime fixup for >=2.x */ + descriptor-types-mask = <01010ebf>; + }; + + pci@8500 { + linux,phandle = <8500>; + interrupt-map-mask = <f800 0 0 7>; + interrupt-map = < + + /* IDSEL 0x11 AD17 */ + 8800 0 0 1 700 14 8 + 8800 0 0 2 700 15 8 + 8800 0 0 3 700 16 8 + 8800 0 0 4 700 17 8 + + /* IDSEL 0x12 AD18 */ + 9000 0 0 1 700 16 8 + 9000 0 0 2 700 17 8 + 9000 0 0 3 700 14 8 + 9000 0 0 4 700 15 8 + + /* IDSEL 0x13 AD19 */ + 9800 0 0 1 700 17 8 + 9800 0 0 2 700 14 8 + 9800 0 0 3 700 15 8 + 9800 0 0 4 700 16 8 + + /* IDSEL 0x15 AD21*/ + a800 0 0 1 700 14 8 + a800 0 0 2 700 15 8 + a800 0 0 3 700 16 8 + a800 0 0 4 700 17 8 + + /* IDSEL 0x16 AD22*/ + b000 0 0 1 700 17 8 + b000 0 0 2 700 14 8 + b000 0 0 3 700 15 8 + b000 0 0 4 700 16 8 + + /* IDSEL 0x17 AD23*/ + b800 0 0 1 700 16 8 + b800 0 0 2 700 17 8 + b800 0 0 3 700 14 8 + b800 0 0 4 700 15 8 + + /* IDSEL 0x18 AD24*/ + c000 0 0 1 700 15 8 + c000 0 0 2 700 16 8 + c000 0 0 3 700 17 8 + c000 0 0 4 700 14 8>; + interrupt-parent = <700>; + interrupts = <42 8>; + bus-range = <0 0>; + ranges = <02000000 0 a0000000 a0000000 0 10000000 + 42000000 0 80000000 80000000 0 10000000 + 01000000 0 00000000 e2000000 0 00100000>; + clock-frequency = <3f940aa>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <8500 100>; + compatible = "83xx"; + device_type = "pci"; + }; + + pic@700 { + linux,phandle = <700>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <700 100>; + built-in; + device_type = "ipic"; + }; + + par_io@1400 { + reg = <1400 100>; + device_type = "par_io"; + num-ports = <7>; + + ucc_pin@01 { + linux,phandle = <140001>; + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 3 1 0 1 0 /* TxD0 */ + 0 4 1 0 1 0 /* TxD1 */ + 0 5 1 0 1 0 /* TxD2 */ + 0 6 1 0 1 0 /* TxD3 */ + 1 6 1 0 3 0 /* TxD4 */ + 1 7 1 0 1 0 /* TxD5 */ + 1 9 1 0 2 0 /* TxD6 */ + 1 a 1 0 2 0 /* TxD7 */ + 0 9 2 0 1 0 /* RxD0 */ + 0 a 2 0 1 0 /* RxD1 */ + 0 b 2 0 1 0 /* RxD2 */ + 0 c 2 0 1 0 /* RxD3 */ + 0 d 2 0 1 0 /* RxD4 */ + 1 1 2 0 2 0 /* RxD5 */ + 1 0 2 0 2 0 /* RxD6 */ + 1 4 2 0 2 0 /* RxD7 */ + 0 7 1 0 1 0 /* TX_EN */ + 0 8 1 0 1 0 /* TX_ER */ + 0 f 2 0 1 0 /* RX_DV */ + 0 10 2 0 1 0 /* RX_ER */ + 0 0 2 0 1 0 /* RX_CLK */ + 2 9 1 0 3 0 /* GTX_CLK - CLK10 */ + 2 8 2 0 1 0>; /* GTX125 - CLK9 */ + }; + ucc_pin@02 { + linux,phandle = <140002>; + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 11 1 0 1 0 /* TxD0 */ + 0 12 1 0 1 0 /* TxD1 */ + 0 13 1 0 1 0 /* TxD2 */ + 0 14 1 0 1 0 /* TxD3 */ + 1 2 1 0 1 0 /* TxD4 */ + 1 3 1 0 2 0 /* TxD5 */ + 1 5 1 0 3 0 /* TxD6 */ + 1 8 1 0 3 0 /* TxD7 */ + 0 17 2 0 1 0 /* RxD0 */ + 0 18 2 0 1 0 /* RxD1 */ + 0 19 2 0 1 0 /* RxD2 */ + 0 1a 2 0 1 0 /* RxD3 */ + 0 1b 2 0 1 0 /* RxD4 */ + 1 c 2 0 2 0 /* RxD5 */ + 1 d 2 0 3 0 /* RxD6 */ + 1 b 2 0 2 0 /* RxD7 */ + 0 15 1 0 1 0 /* TX_EN */ + 0 16 1 0 1 0 /* TX_ER */ + 0 1d 2 0 1 0 /* RX_DV */ + 0 1e 2 0 1 0 /* RX_ER */ + 0 1f 2 0 1 0 /* RX_CLK */ + 2 2 1 0 2 0 /* GTX_CLK - CLK10 */ + 2 3 2 0 1 0 /* GTX125 - CLK4 */ + 0 1 3 0 2 0 /* MDIO */ + 0 2 1 0 1 0>; /* MDC */ + }; + + }; + }; + + qe@e0100000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "qe"; + model = "QE"; + ranges = <0 e0100000 00100000>; + reg = <e0100000 480>; + brg-frequency = <0>; + bus-frequency = <179A7B00>; + + muram@10000 { + device_type = "muram"; + ranges = <0 00010000 0000c000>; + + data-only@0{ + reg = <0 c000>; + }; + }; + + spi@4c0 { + device_type = "spi"; + compatible = "fsl_spi"; + reg = <4c0 40>; + interrupts = <2>; + interrupt-parent = <80>; + mode = "cpu"; + }; + + spi@500 { + device_type = "spi"; + compatible = "fsl_spi"; + reg = <500 40>; + interrupts = <1>; + interrupt-parent = <80>; + mode = "cpu"; + }; + + usb@6c0 { + device_type = "usb"; + compatible = "qe_udc"; + reg = <6c0 40 8B00 100>; + interrupts = <b>; + interrupt-parent = <80>; + mode = "slave"; + }; + + ucc@2000 { + device_type = "network"; + compatible = "ucc_geth"; + model = "UCC"; + device-id = <1>; + reg = <2000 200>; + interrupts = <20>; + interrupt-parent = <80>; + mac-address = [ 00 04 9f 00 23 23 ]; + rx-clock = <0>; + tx-clock = <19>; + phy-handle = <212000>; + pio-handle = <140001>; + }; + + ucc@3000 { + device_type = "network"; + compatible = "ucc_geth"; + model = "UCC"; + device-id = <2>; + reg = <3000 200>; + interrupts = <21>; + interrupt-parent = <80>; + mac-address = [ 00 11 22 33 44 55 ]; + rx-clock = <0>; + tx-clock = <14>; + phy-handle = <212001>; + pio-handle = <140002>; + }; + + mdio@2120 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2120 18>; + device_type = "mdio"; + compatible = "ucc_geth_phy"; + + ethernet-phy@00 { + linux,phandle = <212000>; + interrupt-parent = <700>; + interrupts = <11 2>; + reg = <0>; + device_type = "ethernet-phy"; + interface = <6>; //ENET_1000_GMII + }; + ethernet-phy@01 { + linux,phandle = <212001>; + interrupt-parent = <700>; + interrupts = <12 2>; + reg = <1>; + device_type = "ethernet-phy"; + interface = <6>; + }; + }; + + qeic@80 { + linux,phandle = <80>; + interrupt-controller; + device_type = "qeic"; + #address-cells = <0>; + #interrupt-cells = <1>; + reg = <80 80>; + built-in; + big-endian; + interrupts = <20 8 21 8>; //high:32 low:33 + interrupt-parent = <700>; + }; + + }; +}; diff --git a/arch/powerpc/boot/zImage.coff.lds.S b/arch/powerpc/boot/zImage.coff.lds.S index 6016251a1a2c..05f32388b953 100644 --- a/arch/powerpc/boot/zImage.coff.lds.S +++ b/arch/powerpc/boot/zImage.coff.lds.S @@ -15,6 +15,7 @@ SECTIONS { *(.rodata*) *(.data*) + *(__builtin_*) *(.sdata*) __got2_start = .; *(.got2) diff --git a/arch/powerpc/configs/mpc8360emds_defconfig b/arch/powerpc/configs/mpc8360emds_defconfig new file mode 100644 index 000000000000..c0703415d608 --- /dev/null +++ b/arch/powerpc/configs/mpc8360emds_defconfig @@ -0,0 +1,1018 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.18 +# Thu Sep 21 18:14:27 2006 +# +# CONFIG_PPC64 is not set +CONFIG_PPC32=y +CONFIG_PPC_MERGE=y +CONFIG_MMU=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_IRQ_PER_CPU=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +CONFIG_PPC_UDBG_16550=y +# CONFIG_GENERIC_TBSYNC is not set +CONFIG_AUDIT_ARCH=y +CONFIG_DEFAULT_UIMAGE=y + +# +# Processor support +# +# CONFIG_CLASSIC32 is not set +# CONFIG_PPC_52xx is not set +# CONFIG_PPC_82xx is not set +CONFIG_PPC_83xx=y +# CONFIG_PPC_85xx is not set +# CONFIG_PPC_86xx is not set +# CONFIG_40x is not set +# CONFIG_44x is not set +# CONFIG_8xx is not set +# CONFIG_E200 is not set +CONFIG_6xx=y +CONFIG_83xx=y +CONFIG_PPC_FPU=y +CONFIG_PPC_STD_MMU=y +CONFIG_PPC_STD_MMU_32=y +# CONFIG_SMP is not set +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +# CONFIG_RELAY is not set +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_EMBEDDED=y +CONFIG_SYSCTL=y +# CONFIG_KALLSYMS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +# CONFIG_EPOLL is not set +CONFIG_SHMEM=y +CONFIG_SLAB=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +# CONFIG_SLOB is not set + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +# CONFIG_KMOD is not set + +# +# Block layer +# +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_QUICC_ENGINE=y +CONFIG_PPC_GEN550=y +# CONFIG_WANT_EARLY_SERIAL is not set + +# +# Platform support +# +# CONFIG_MPC834x_SYS is not set +# CONFIG_MPC834x_ITX is not set +CONFIG_MPC8360E_PB=y +CONFIG_PPC_MPC836x=y +# CONFIG_MPIC is not set + +# +# Kernel options +# +# CONFIG_HIGHMEM is not set +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_MISC is not set +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_PROC_DEVICETREE=y +# CONFIG_CMDLINE_BOOL is not set +# CONFIG_PM is not set +CONFIG_SECCOMP=y +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +CONFIG_GENERIC_ISA_DMA=y +# CONFIG_MPIC_WEIRD is not set +# CONFIG_PPC_I8259 is not set +CONFIG_PPC_INDIRECT_PCI=y +CONFIG_FSL_SOC=y +CONFIG_PCI=y +CONFIG_PCI_DOMAINS=y +# CONFIG_PCIEPORTBUS is not set + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set + +# +# PCI Hotplug Support +# +# CONFIG_HOTPLUG_PCI is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_HIGHMEM_START=0xfe000000 +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_TASK_SIZE=0x80000000 +CONFIG_BOOT_LOAD=0x00800000 + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +# CONFIG_NETDEBUG is not set +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +CONFIG_SYN_COOKIES=y +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_BIC=y +# CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_SYS_HYPERVISOR is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# +# Memory Technology Devices (MTD) +# +# CONFIG_MTD is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# + +# +# Block devices +# +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_SX8 is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=32768 +CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 +CONFIG_BLK_DEV_INITRD=y +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# ATA/ATAPI/MFM/RLL support +# +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +# CONFIG_BLK_DEV_SD is not set +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set + +# +# SCSI Transport Attributes +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_ATTRS is not set + +# +# SCSI low-level drivers +# +# CONFIG_ISCSI_TCP is not set +# CONFIG_BLK_DEV_3W_XXXX_RAID is not set +# CONFIG_SCSI_3W_9XXX is not set +# CONFIG_SCSI_ACARD is not set +# CONFIG_SCSI_AACRAID is not set +# CONFIG_SCSI_AIC7XXX is not set +# CONFIG_SCSI_AIC7XXX_OLD is not set +# CONFIG_SCSI_AIC79XX is not set +# CONFIG_SCSI_DPT_I2O is not set +# CONFIG_MEGARAID_NEWGEN is not set +# CONFIG_MEGARAID_LEGACY is not set +# CONFIG_MEGARAID_SAS is not set +# CONFIG_SCSI_SATA is not set +# CONFIG_SCSI_HPTIOP is not set +# CONFIG_SCSI_BUSLOGIC is not set +# CONFIG_SCSI_DMX3191D is not set +# CONFIG_SCSI_EATA is not set +# CONFIG_SCSI_FUTURE_DOMAIN is not set +# CONFIG_SCSI_GDTH is not set +# CONFIG_SCSI_IPS is not set +# CONFIG_SCSI_INITIO is not set +# CONFIG_SCSI_INIA100 is not set +# CONFIG_SCSI_SYM53C8XX_2 is not set +# CONFIG_SCSI_IPR is not set +# CONFIG_SCSI_QLOGIC_1280 is not set +# CONFIG_SCSI_QLA_FC is not set +# CONFIG_SCSI_LPFC is not set +# CONFIG_SCSI_DC395x is not set +# CONFIG_SCSI_DC390T is not set +# CONFIG_SCSI_NSP32 is not set +# CONFIG_SCSI_DEBUG is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set +# CONFIG_FUSION_SPI is not set +# CONFIG_FUSION_FC is not set +# CONFIG_FUSION_SAS is not set + +# +# IEEE 1394 (FireWire) support +# +# CONFIG_IEEE1394 is not set + +# +# I2O device support +# +# CONFIG_I2O is not set + +# +# Macintosh device drivers +# +# CONFIG_WINDFARM is not set + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# ARCnet devices +# +# CONFIG_ARCNET is not set + +# +# PHY device support +# +# CONFIG_PHYLIB is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_HAPPYMEAL is not set +# CONFIG_SUNGEM is not set +# CONFIG_CASSINI is not set +# CONFIG_NET_VENDOR_3COM is not set + +# +# Tulip family network device support +# +# CONFIG_NET_TULIP is not set +# CONFIG_HP100 is not set +# CONFIG_NET_PCI is not set + +# +# Ethernet (1000 Mbit) +# +# CONFIG_ACENIC is not set +# CONFIG_DL2K is not set +# CONFIG_E1000 is not set +# CONFIG_NS83820 is not set +# CONFIG_HAMACHI is not set +# CONFIG_YELLOWFIN is not set +# CONFIG_R8169 is not set +# CONFIG_SIS190 is not set +# CONFIG_SKGE is not set +# CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set +# CONFIG_TIGON3 is not set +# CONFIG_BNX2 is not set +# CONFIG_GIANFAR is not set +CONFIG_UCC_GETH=y +# CONFIG_UGETH_NAPI is not set +# CONFIG_UGETH_MAGIC_PACKET is not set +# CONFIG_UGETH_FILTERING is not set +# CONFIG_UGETH_TX_ON_DEMOND is not set + +# +# Ethernet (10000 Mbit) +# +# CONFIG_CHELSIO_T1 is not set +# CONFIG_IXGB is not set +# CONFIG_S2IO is not set +# CONFIG_MYRI10GE is not set + +# +# Token Ring devices +# +# CONFIG_TR is not set + +# +# Wireless LAN (non-hamradio) +# +# CONFIG_NET_RADIO is not set + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NET_FC is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Telephony Support +# +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_VT is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +# CONFIG_SERIAL_8250_EXTENDED is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_83xx_WDT=y + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set +CONFIG_HW_RANDOM=y +# CONFIG_NVRAM is not set +CONFIG_GEN_RTC=y +# CONFIG_GEN_RTC_X is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set + +# +# Ftape, the floppy tape device driver +# +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set +# CONFIG_TELCLOCK is not set + +# +# I2C support +# +CONFIG_I2C=y +CONFIG_I2C_CHARDEV=y + +# +# I2C Algorithms +# +# CONFIG_I2C_ALGOBIT is not set +# CONFIG_I2C_ALGOPCF is not set +# CONFIG_I2C_ALGOPCA is not set + +# +# I2C Hardware Bus support +# +# CONFIG_I2C_ALI1535 is not set +# CONFIG_I2C_ALI1563 is not set +# CONFIG_I2C_ALI15X3 is not set +# CONFIG_I2C_AMD756 is not set +# CONFIG_I2C_AMD8111 is not set +# CONFIG_I2C_I801 is not set +# CONFIG_I2C_I810 is not set +# CONFIG_I2C_PIIX4 is not set +CONFIG_I2C_MPC=y +# CONFIG_I2C_NFORCE2 is not set +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_PROSAVAGE is not set +# CONFIG_I2C_SAVAGE4 is not set +# CONFIG_I2C_SIS5595 is not set +# CONFIG_I2C_SIS630 is not set +# CONFIG_I2C_SIS96X is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_VIA is not set +# CONFIG_I2C_VIAPRO is not set +# CONFIG_I2C_VOODOO3 is not set +# CONFIG_I2C_PCA_ISA is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_SENSORS_DS1337 is not set +# CONFIG_SENSORS_DS1374 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_M41T00 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set + +# +# SPI support +# +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set + +# +# Dallas's 1-wire bus +# + +# +# Hardware Monitoring support +# +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_ABITUGURU is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ATXP1 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_FSCHER is not set +# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM75 is not set +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_LM92 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_SIS5595 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47M192 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_VIA686A is not set +# CONFIG_SENSORS_VT8231 is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83791D is not set +# CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_HWMON_DEBUG_CHIP is not set + +# +# Misc devices +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set +CONFIG_VIDEO_V4L2=y + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set + +# +# Graphics support +# +CONFIG_FIRMWARE_EDID=y +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# USB support +# +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +# CONFIG_USB is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# USB Gadget Support +# +# CONFIG_USB_GADGET is not set + +# +# MMC/SD Card support +# +# CONFIG_MMC is not set + +# +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# +# InfiniBand support +# +# CONFIG_INFINIBAND is not set + +# +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock +# +# CONFIG_RTC_CLASS is not set + +# +# DMA Engine support +# +# CONFIG_DMA_ENGINE is not set + +# +# DMA Clients +# + +# +# DMA Devices +# + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +CONFIG_EXT3_FS_XATTR=y +# CONFIG_EXT3_FS_POSIX_ACL is not set +# CONFIG_EXT3_FS_SECURITY is not set +CONFIG_JBD=y +# CONFIG_JBD_DEBUG is not set +CONFIG_FS_MBCACHE=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +CONFIG_NFS_V4=y +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +# CONFIG_MSDOS_PARTITION is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set + +# +# Native Language Support +# +# CONFIG_NLS is not set + +# +# QE Options +# +# CONFIG_UCC_SLOW is not set +CONFIG_UCC_FAST=y +CONFIG_UCC=y + +# +# Library routines +# +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +CONFIG_PLIST=y + +# +# Instrumentation Support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_KERNEL is not set +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_DEBUG_FS is not set +# CONFIG_BOOTX_TEXT is not set +# CONFIG_SERIAL_TEXT_DEBUG is not set +# CONFIG_PPC_EARLY_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +CONFIG_CRYPTO=y +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_WP512 is not set +# CONFIG_CRYPTO_TGR192 is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_TWOFISH is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Hardware crypto devices +# diff --git a/arch/powerpc/kernel/cputable.c b/arch/powerpc/kernel/cputable.c index 190a57e20765..47a613cdd775 100644 --- a/arch/powerpc/kernel/cputable.c +++ b/arch/powerpc/kernel/cputable.c @@ -763,10 +763,10 @@ struct cpu_spec cpu_specs[] = { .cpu_setup = __setup_cpu_603, .platform = "ppc603", }, - { /* e300 (a 603e core, plus some) on 83xx */ + { /* e300c1 (a 603e core, plus some) on 83xx */ .pvr_mask = 0x7fff0000, .pvr_value = 0x00830000, - .cpu_name = "e300", + .cpu_name = "e300c1", .cpu_features = CPU_FTRS_E300, .cpu_user_features = COMMON_USER, .icache_bsize = 32, @@ -774,6 +774,17 @@ struct cpu_spec cpu_specs[] = { .cpu_setup = __setup_cpu_603, .platform = "ppc603", }, + { /* e300c2 (an e300c1 core, plus some, minus FPU) on 83xx */ + .pvr_mask = 0x7fff0000, + .pvr_value = 0x00840000, + .cpu_name = "e300c2", + .cpu_features = CPU_FTRS_E300, + .cpu_user_features = PPC_FEATURE_32 | PPC_FEATURE_HAS_MMU, + .icache_bsize = 32, + .dcache_bsize = 32, + .cpu_setup = __setup_cpu_603, + .platform = "ppc603", + }, { /* default match, we assume split I/D cache & TB (non-601)... */ .pvr_mask = 0x00000000, .pvr_value = 0x00000000, diff --git a/arch/powerpc/kernel/entry_64.S b/arch/powerpc/kernel/entry_64.S index 2cd872b5283b..748e74fcf541 100644 --- a/arch/powerpc/kernel/entry_64.S +++ b/arch/powerpc/kernel/entry_64.S @@ -27,10 +27,7 @@ #include <asm/ppc_asm.h> #include <asm/asm-offsets.h> #include <asm/cputable.h> - -#ifdef CONFIG_PPC_ISERIES -#define DO_SOFT_DISABLE -#endif +#include <asm/firmware.h> /* * System calls. @@ -91,6 +88,7 @@ system_call_common: ld r11,exception_marker@toc(r2) std r11,-16(r9) /* "regshere" marker */ #ifdef CONFIG_PPC_ISERIES +BEGIN_FW_FTR_SECTION /* Hack for handling interrupts when soft-enabling on iSeries */ cmpdi cr1,r0,0x5555 /* syscall 0x5555 */ andi. r10,r12,MSR_PR /* from kernel */ @@ -98,6 +96,7 @@ system_call_common: beq hardware_interrupt_entry lbz r10,PACAPROCENABLED(r13) std r10,SOFTE(r1) +END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) #endif mfmsr r11 ori r11,r11,MSR_EE @@ -462,6 +461,7 @@ _GLOBAL(ret_from_except_lite) restore: #ifdef CONFIG_PPC_ISERIES +BEGIN_FW_FTR_SECTION ld r5,SOFTE(r1) cmpdi 0,r5,0 beq 4f @@ -480,6 +480,7 @@ restore: b .ret_from_except_lite /* loop back and handle more */ 4: stb r5,PACAPROCENABLED(r13) +END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) #endif ld r3,_MSR(r1) @@ -538,18 +539,23 @@ do_work: lwz r8,TI_PREEMPT(r9) cmpwi cr1,r8,0 #ifdef CONFIG_PPC_ISERIES +BEGIN_FW_FTR_SECTION ld r0,SOFTE(r1) cmpdi r0,0 -#else - andi. r0,r3,MSR_EE +END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) #endif +BEGIN_FW_FTR_SECTION + andi. r0,r3,MSR_EE +END_FW_FTR_SECTION_IFCLR(FW_FEATURE_ISERIES) crandc eq,cr1*4+eq,eq bne restore /* here we are preempting the current task */ 1: #ifdef CONFIG_PPC_ISERIES +BEGIN_FW_FTR_SECTION li r0,1 stb r0,PACAPROCENABLED(r13) +END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) #endif ori r10,r10,MSR_EE mtmsrd r10,1 /* reenable interrupts */ diff --git a/arch/powerpc/kernel/head_64.S b/arch/powerpc/kernel/head_64.S index 3065b472b95d..645c7f10fb28 100644 --- a/arch/powerpc/kernel/head_64.S +++ b/arch/powerpc/kernel/head_64.S @@ -33,6 +33,7 @@ #include <asm/hvcall.h> #include <asm/iseries/lpar_map.h> #include <asm/thread_info.h> +#include <asm/firmware.h> #ifdef CONFIG_PPC_ISERIES #define DO_SOFT_DISABLE @@ -365,19 +366,28 @@ label##_iSeries: \ #ifdef DO_SOFT_DISABLE #define DISABLE_INTS \ +BEGIN_FW_FTR_SECTION; \ lbz r10,PACAPROCENABLED(r13); \ li r11,0; \ std r10,SOFTE(r1); \ mfmsr r10; \ stb r11,PACAPROCENABLED(r13); \ ori r10,r10,MSR_EE; \ - mtmsrd r10,1 + mtmsrd r10,1; \ +END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) #define ENABLE_INTS \ +BEGIN_FW_FTR_SECTION; \ lbz r10,PACAPROCENABLED(r13); \ mfmsr r11; \ std r10,SOFTE(r1); \ ori r11,r11,MSR_EE; \ +END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES); \ +BEGIN_FW_FTR_SECTION; \ + ld r12,_MSR(r1); \ + mfmsr r11; \ + rlwimi r11,r12,0,MSR_EE; \ +END_FW_FTR_SECTION_IFCLR(FW_FEATURE_ISERIES); \ mtmsrd r11,1 #else /* hard enable/disable interrupts */ @@ -1071,8 +1081,10 @@ _GLOBAL(slb_miss_realmode) ld r3,PACA_EXSLB+EX_R3(r13) lwz r9,PACA_EXSLB+EX_CCR(r13) /* get saved CR */ #ifdef CONFIG_PPC_ISERIES +BEGIN_FW_FTR_SECTION ld r11,PACALPPACAPTR(r13) ld r11,LPPACASRR0(r11) /* get SRR0 value */ +END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) #endif /* CONFIG_PPC_ISERIES */ mtlr r10 @@ -1087,8 +1099,10 @@ _GLOBAL(slb_miss_realmode) .machine pop #ifdef CONFIG_PPC_ISERIES +BEGIN_FW_FTR_SECTION mtspr SPRN_SRR0,r11 mtspr SPRN_SRR1,r12 +END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) #endif /* CONFIG_PPC_ISERIES */ ld r9,PACA_EXSLB+EX_R9(r13) ld r10,PACA_EXSLB+EX_R10(r13) @@ -1301,6 +1315,7 @@ END_FTR_SECTION_IFCLR(CPU_FTR_SLB) cmpdi r3,0 /* see if hash_page succeeded */ #ifdef DO_SOFT_DISABLE +BEGIN_FW_FTR_SECTION /* * If we had interrupts soft-enabled at the point where the * DSI/ISI occurred, and an interrupt came in during hash_page, @@ -1321,12 +1336,14 @@ END_FTR_SECTION_IFCLR(CPU_FTR_SLB) ld r3,SOFTE(r1) bl .local_irq_restore b 11f -#else +END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) +#endif +BEGIN_FW_FTR_SECTION beq fast_exception_return /* Return from exception on success */ ble- 12f /* Failure return from hash_page */ /* fall through */ -#endif +END_FW_FTR_SECTION_IFCLR(FW_FEATURE_ISERIES) /* Here we have a page fault that hash_page can't handle. */ _GLOBAL(handle_page_fault) @@ -1861,7 +1878,9 @@ _GLOBAL(__secondary_start) LOAD_REG_ADDR(r3, .start_secondary_prolog) LOAD_REG_IMMEDIATE(r4, MSR_KERNEL) #ifdef DO_SOFT_DISABLE +BEGIN_FW_FTR_SECTION ori r4,r4,MSR_EE +END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) #endif mtspr SPRN_SRR0,r3 mtspr SPRN_SRR1,r4 @@ -1986,6 +2005,7 @@ _STATIC(start_here_common) */ li r3,0 bl .do_cpu_ftr_fixups + bl .do_fw_ftr_fixups /* ptr to current */ LOAD_REG_IMMEDIATE(r4, init_task) @@ -2000,11 +2020,13 @@ _STATIC(start_here_common) /* Load up the kernel context */ 5: #ifdef DO_SOFT_DISABLE +BEGIN_FW_FTR_SECTION li r5,0 stb r5,PACAPROCENABLED(r13) /* Soft Disabled */ mfmsr r5 ori r5,r5,MSR_EE /* Hard Enabled */ mtmsrd r5 +END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) #endif bl .start_kernel diff --git a/arch/powerpc/kernel/misc_64.S b/arch/powerpc/kernel/misc_64.S index 9c54eccad993..41521b30c3cd 100644 --- a/arch/powerpc/kernel/misc_64.S +++ b/arch/powerpc/kernel/misc_64.S @@ -325,6 +325,52 @@ _GLOBAL(do_cpu_ftr_fixups) isync b 1b +/* + * do_fw_ftr_fixups - goes through the list of firmware feature fixups + * and writes nop's over sections of code that don't apply for this firmware. + * r3 = data offset (not changed) + */ +_GLOBAL(do_fw_ftr_fixups) + /* Get firmware features */ + LOAD_REG_IMMEDIATE(r6,powerpc_firmware_features) + sub r6,r6,r3 + ld r4,0(r6) + /* Get the fixup table */ + LOAD_REG_IMMEDIATE(r6,__start___fw_ftr_fixup) + sub r6,r6,r3 + LOAD_REG_IMMEDIATE(r7,__stop___fw_ftr_fixup) + sub r7,r7,r3 + /* Do the fixup */ +1: cmpld r6,r7 + bgelr + addi r6,r6,32 + ld r8,-32(r6) /* mask */ + and r8,r8,r4 + ld r9,-24(r6) /* value */ + cmpld r8,r9 + beq 1b + ld r8,-16(r6) /* section begin */ + ld r9,-8(r6) /* section end */ + subf. r9,r8,r9 + beq 1b + /* write nops over the section of code */ + /* todo: if large section, add a branch at the start of it */ + srwi r9,r9,2 + mtctr r9 + sub r8,r8,r3 + lis r0,0x60000000@h /* nop */ +3: stw r0,0(r8) +BEGIN_FTR_SECTION + dcbst 0,r8 /* suboptimal, but simpler */ + sync + icbi 0,r8 +END_FTR_SECTION_IFSET(CPU_FTR_SPLIT_ID_CACHE) + addi r8,r8,4 + bdnz 3b + sync /* additional sync needed on g4 */ + isync + b 1b + #if defined(CONFIG_PPC_PMAC) || defined(CONFIG_PPC_MAPLE) /* * Do an IO access in real mode diff --git a/arch/powerpc/kernel/pci_64.c b/arch/powerpc/kernel/pci_64.c index c1b1e14775e4..78d3c0fc8dfb 100644 --- a/arch/powerpc/kernel/pci_64.c +++ b/arch/powerpc/kernel/pci_64.c @@ -30,6 +30,7 @@ #include <asm/byteorder.h> #include <asm/machdep.h> #include <asm/ppc-pci.h> +#include <asm/firmware.h> #ifdef DEBUG #include <asm/udbg.h> @@ -209,7 +210,6 @@ void pcibios_free_controller(struct pci_controller *phb) kfree(phb); } -#ifndef CONFIG_PPC_ISERIES void __devinit pcibios_claim_one_bus(struct pci_bus *b) { struct pci_dev *dev; @@ -238,10 +238,12 @@ static void __init pcibios_claim_of_setup(void) { struct pci_bus *b; + if (firmware_has_feature(FW_FEATURE_ISERIES)) + return; + list_for_each_entry(b, &pci_root_buses, node) pcibios_claim_one_bus(b); } -#endif #ifdef CONFIG_PPC_MULTIPLATFORM static u32 get_int_prop(struct device_node *np, const char *name, u32 def) @@ -554,9 +556,8 @@ static int __init pcibios_init(void) */ ppc_md.phys_mem_access_prot = pci_phys_mem_access_prot; -#ifdef CONFIG_PPC_ISERIES - iSeries_pcibios_init(); -#endif + if (firmware_has_feature(FW_FEATURE_ISERIES)) + iSeries_pcibios_init(); printk(KERN_DEBUG "PCI: Probing PCI hardware\n"); @@ -566,15 +567,15 @@ static int __init pcibios_init(void) pci_bus_add_devices(hose->bus); } -#ifndef CONFIG_PPC_ISERIES - if (pci_probe_only) - pcibios_claim_of_setup(); - else - /* FIXME: `else' will be removed when - pci_assign_unassigned_resources() is able to work - correctly with [partially] allocated PCI tree. */ - pci_assign_unassigned_resources(); -#endif /* !CONFIG_PPC_ISERIES */ + if (!firmware_has_feature(FW_FEATURE_ISERIES)) { + if (pci_probe_only) + pcibios_claim_of_setup(); + else + /* FIXME: `else' will be removed when + pci_assign_unassigned_resources() is able to work + correctly with [partially] allocated PCI tree. */ + pci_assign_unassigned_resources(); + } /* Call machine dependent final fixup */ if (ppc_md.pcibios_fixup) @@ -586,8 +587,9 @@ static int __init pcibios_init(void) printk(KERN_DEBUG "ISA bridge at %s\n", pci_name(ppc64_isabridge_dev)); #ifdef CONFIG_PPC_MULTIPLATFORM - /* map in PCI I/O space */ - phbs_remap_io(); + if (!firmware_has_feature(FW_FEATURE_ISERIES)) + /* map in PCI I/O space */ + phbs_remap_io(); #endif printk(KERN_DEBUG "PCI: Probing PCI hardware done\n"); @@ -637,13 +639,13 @@ int pcibios_enable_device(struct pci_dev *dev, int mask) */ int pci_domain_nr(struct pci_bus *bus) { -#ifdef CONFIG_PPC_ISERIES - return 0; -#else - struct pci_controller *hose = pci_bus_to_host(bus); + if (firmware_has_feature(FW_FEATURE_ISERIES)) + return 0; + else { + struct pci_controller *hose = pci_bus_to_host(bus); - return hose->global_number; -#endif + return hose->global_number; + } } EXPORT_SYMBOL(pci_domain_nr); @@ -651,12 +653,12 @@ EXPORT_SYMBOL(pci_domain_nr); /* Decide whether to display the domain number in /proc */ int pci_proc_domain(struct pci_bus *bus) { -#ifdef CONFIG_PPC_ISERIES - return 0; -#else - struct pci_controller *hose = pci_bus_to_host(bus); - return hose->buid; -#endif + if (firmware_has_feature(FW_FEATURE_ISERIES)) + return 0; + else { + struct pci_controller *hose = pci_bus_to_host(bus); + return hose->buid; + } } /* diff --git a/arch/powerpc/kernel/setup-common.c b/arch/powerpc/kernel/setup-common.c index 0af3fc1bdcc9..89cfaf49d3de 100644 --- a/arch/powerpc/kernel/setup-common.c +++ b/arch/powerpc/kernel/setup-common.c @@ -442,31 +442,6 @@ void __init smp_setup_cpu_maps(void) } #endif /* CONFIG_SMP */ -int __initdata do_early_xmon; -#ifdef CONFIG_XMON -extern int xmon_no_auto_backtrace; - -static int __init early_xmon(char *p) -{ - /* ensure xmon is enabled */ - if (p) { - if (strncmp(p, "on", 2) == 0) - xmon_init(1); - if (strncmp(p, "off", 3) == 0) - xmon_init(0); - if (strncmp(p, "nobt", 4) == 0) - xmon_no_auto_backtrace = 1; - if (strncmp(p, "early", 5) != 0) - return 0; - } - xmon_init(1); - do_early_xmon = 1; - - return 0; -} -early_param("xmon", early_xmon); -#endif - static __init int add_pcspkr(void) { struct device_node *np; diff --git a/arch/powerpc/kernel/setup_32.c b/arch/powerpc/kernel/setup_32.c index 79a17795d17b..191d0ab09222 100644 --- a/arch/powerpc/kernel/setup_32.c +++ b/arch/powerpc/kernel/setup_32.c @@ -238,12 +238,11 @@ void __init setup_arch(char **cmdline_p) smp_setup_cpu_maps(); -#ifdef CONFIG_XMON_DEFAULT - xmon_init(1); -#endif /* Register early console */ register_early_udbg_console(); + xmon_setup(); + #if defined(CONFIG_KGDB) if (ppc_md.kgdb_map_scc) ppc_md.kgdb_map_scc(); @@ -280,9 +279,6 @@ void __init setup_arch(char **cmdline_p) init_mm.end_data = (unsigned long) _edata; init_mm.brk = klimit; - if (do_early_xmon) - debugger(NULL); - /* set up the bootmem stuff with available memory */ do_init_bootmem(); if ( ppc_md.progress ) ppc_md.progress("setup_arch: bootmem", 0x3eab); diff --git a/arch/powerpc/kernel/setup_64.c b/arch/powerpc/kernel/setup_64.c index cda2dbe70a76..4b2e32eab9dc 100644 --- a/arch/powerpc/kernel/setup_64.c +++ b/arch/powerpc/kernel/setup_64.c @@ -391,18 +391,14 @@ void __init setup_system(void) find_legacy_serial_ports(); /* - * Initialize xmon - */ -#ifdef CONFIG_XMON_DEFAULT - xmon_init(1); -#endif - /* * Register early console */ register_early_udbg_console(); - if (do_early_xmon) - debugger(NULL); + /* + * Initialize xmon + */ + xmon_setup(); check_smt_enabled(); smp_setup_cpu_maps(); diff --git a/arch/powerpc/kernel/vmlinux.lds.S b/arch/powerpc/kernel/vmlinux.lds.S index 02665a02130d..cb0e8d46c3e8 100644 --- a/arch/powerpc/kernel/vmlinux.lds.S +++ b/arch/powerpc/kernel/vmlinux.lds.S @@ -132,6 +132,14 @@ SECTIONS *(__ftr_fixup) __stop___ftr_fixup = .; } +#ifdef CONFIG_PPC64 + . = ALIGN(8); + __fw_ftr_fixup : { + __start___fw_ftr_fixup = .; + *(__fw_ftr_fixup) + __stop___fw_ftr_fixup = .; + } +#endif . = ALIGN(PAGE_SIZE); .init.ramfs : { diff --git a/arch/powerpc/mm/pgtable_64.c b/arch/powerpc/mm/pgtable_64.c index b1da03165496..ac64f4aaa509 100644 --- a/arch/powerpc/mm/pgtable_64.c +++ b/arch/powerpc/mm/pgtable_64.c @@ -63,32 +63,13 @@ #include <asm/iommu.h> #include <asm/abs_addr.h> #include <asm/vdso.h> +#include <asm/firmware.h> #include "mmu_decl.h" unsigned long ioremap_bot = IMALLOC_BASE; static unsigned long phbs_io_bot = PHBS_IO_BASE; -#ifdef CONFIG_PPC_ISERIES - -void __iomem *ioremap(unsigned long addr, unsigned long size) -{ - return (void __iomem *)addr; -} - -extern void __iomem *__ioremap(unsigned long addr, unsigned long size, - unsigned long flags) -{ - return (void __iomem *)addr; -} - -void iounmap(volatile void __iomem *addr) -{ - return; -} - -#else - /* * map_io_page currently only called by __ioremap * map_io_page adds an entry to the ioremap page table @@ -161,6 +142,9 @@ void __iomem * __ioremap(unsigned long addr, unsigned long size, unsigned long pa, ea; void __iomem *ret; + if (firmware_has_feature(FW_FEATURE_ISERIES)) + return (void __iomem *)addr; + /* * Choose an address to map it to. * Once the imalloc system is running, we use it. @@ -255,6 +239,9 @@ void iounmap(volatile void __iomem *token) { void *addr; + if (firmware_has_feature(FW_FEATURE_ISERIES)) + return; + if (!mem_init_done) return; @@ -315,8 +302,6 @@ int iounmap_explicit(volatile void __iomem *start, unsigned long size) return 0; } -#endif - EXPORT_SYMBOL(ioremap); EXPORT_SYMBOL(__ioremap); EXPORT_SYMBOL(iounmap); diff --git a/arch/powerpc/mm/slb_low.S b/arch/powerpc/mm/slb_low.S index dbc1abbde038..b10e4707d7c1 100644 --- a/arch/powerpc/mm/slb_low.S +++ b/arch/powerpc/mm/slb_low.S @@ -21,6 +21,7 @@ #include <asm/page.h> #include <asm/mmu.h> #include <asm/pgtable.h> +#include <asm/firmware.h> /* void slb_allocate_realmode(unsigned long ea); * @@ -183,6 +184,7 @@ slb_finish_load: * dont have any LRU information to help us choose a slot. */ #ifdef CONFIG_PPC_ISERIES +BEGIN_FW_FTR_SECTION /* * On iSeries, the "bolted" stack segment can be cast out on * shared processor switch so we need to check for a miss on @@ -194,6 +196,7 @@ slb_finish_load: li r10,SLB_NUM_BOLTED-1 /* Stack goes in last bolted slot */ cmpld r9,r3 beq 3f +END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) #endif /* CONFIG_PPC_ISERIES */ ld r10,PACASTABRR(r13) diff --git a/arch/powerpc/platforms/82xx/Kconfig b/arch/powerpc/platforms/82xx/Kconfig new file mode 100644 index 000000000000..47d841ecf2e2 --- /dev/null +++ b/arch/powerpc/platforms/82xx/Kconfig @@ -0,0 +1,21 @@ +menu "Platform support" + depends on PPC_82xx + +choice + prompt "Machine Type" + default MPC82xx_ADS + +config MPC82xx_ADS + bool "Freescale MPC82xx ADS" + select DEFAULT_UIMAGE + select PQ2ADS + select 8272 + select 8260 + select CPM2 + select FSL_SOC + help + This option enables support for the MPC8272 ADS board + +endchoice + +endmenu diff --git a/arch/powerpc/platforms/82xx/Makefile b/arch/powerpc/platforms/82xx/Makefile new file mode 100644 index 000000000000..d9fd4c84d2e0 --- /dev/null +++ b/arch/powerpc/platforms/82xx/Makefile @@ -0,0 +1,5 @@ +# +# Makefile for the PowerPC 82xx linux kernel. +# +obj-$(CONFIG_PPC_82xx) += mpc82xx.o +obj-$(CONFIG_MPC82xx_ADS) += mpc82xx_ads.o diff --git a/arch/powerpc/platforms/82xx/m82xx_pci.h b/arch/powerpc/platforms/82xx/m82xx_pci.h new file mode 100644 index 000000000000..9cd8893b5a32 --- /dev/null +++ b/arch/powerpc/platforms/82xx/m82xx_pci.h @@ -0,0 +1,19 @@ +#ifndef _PPC_KERNEL_M82XX_PCI_H +#define _PPC_KERNEL_M82XX_PCI_H + +/* + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#include <asm/m8260_pci.h> + +#define SIU_INT_IRQ1 ((uint)0x13 + CPM_IRQ_OFFSET) + +#ifndef _IO_BASE +#define _IO_BASE isa_io_base +#endif + +#endif /* _PPC_KERNEL_M8260_PCI_H */ diff --git a/arch/powerpc/platforms/82xx/mpc82xx.c b/arch/powerpc/platforms/82xx/mpc82xx.c new file mode 100644 index 000000000000..89d702de4863 --- /dev/null +++ b/arch/powerpc/platforms/82xx/mpc82xx.c @@ -0,0 +1,111 @@ +/* + * MPC82xx setup and early boot code plus other random bits. + * + * Author: Vitaly Bordug <vbordug@ru.mvista.com> + * + * Copyright (c) 2006 MontaVista Software, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/config.h> +#include <linux/stddef.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/errno.h> +#include <linux/reboot.h> +#include <linux/pci.h> +#include <linux/interrupt.h> +#include <linux/kdev_t.h> +#include <linux/major.h> +#include <linux/console.h> +#include <linux/delay.h> +#include <linux/seq_file.h> +#include <linux/root_dev.h> +#include <linux/initrd.h> +#include <linux/module.h> +#include <linux/fsl_devices.h> +#include <linux/fs_uart_pd.h> + +#include <asm/system.h> +#include <asm/pgtable.h> +#include <asm/page.h> +#include <asm/atomic.h> +#include <asm/time.h> +#include <asm/io.h> +#include <asm/machdep.h> +#include <asm/bootinfo.h> +#include <asm/pci-bridge.h> +#include <asm/mpc8260.h> +#include <asm/irq.h> +#include <mm/mmu_decl.h> +#include <asm/prom.h> +#include <asm/cpm2.h> +#include <asm/udbg.h> +#include <asm/i8259.h> +#include <linux/fs_enet_pd.h> + +#include <sysdev/fsl_soc.h> +#include <sysdev/cpm2_pic.h> + +#include "pq2ads_pd.h" + +static int __init get_freq(char *name, unsigned long *val) +{ + struct device_node *cpu; + unsigned int *fp; + int found = 0; + + /* The cpu node should have timebase and clock frequency properties */ + cpu = of_find_node_by_type(NULL, "cpu"); + + if (cpu) { + fp = (unsigned int *)get_property(cpu, name, NULL); + if (fp) { + found = 1; + *val = *fp++; + } + + of_node_put(cpu); + } + + return found; +} + +void __init m82xx_calibrate_decr(void) +{ + ppc_tb_freq = 125000000; + if (!get_freq("bus-frequency", &ppc_tb_freq)) { + printk(KERN_ERR "WARNING: Estimating decrementer frequency " + "(not found)\n"); + } + ppc_tb_freq /= 4; + ppc_proc_freq = 1000000000; + if (!get_freq("clock-frequency", &ppc_proc_freq)) + printk(KERN_ERR "WARNING: Estimating processor frequency" + "(not found)\n"); +} + +void mpc82xx_ads_show_cpuinfo(struct seq_file *m) +{ + uint pvid, svid, phid1; + uint memsize = total_memory; + + pvid = mfspr(SPRN_PVR); + svid = mfspr(SPRN_SVR); + + seq_printf(m, "Vendor\t\t: Freescale Semiconductor\n"); + seq_printf(m, "Machine\t\t: %s\n", CPUINFO_MACHINE); + seq_printf(m, "PVR\t\t: 0x%x\n", pvid); + seq_printf(m, "SVR\t\t: 0x%x\n", svid); + + /* Display cpu Pll setting */ + phid1 = mfspr(SPRN_HID1); + seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f)); + + /* Display the amount of memory */ + seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024)); +} diff --git a/arch/powerpc/platforms/82xx/mpc82xx_ads.c b/arch/powerpc/platforms/82xx/mpc82xx_ads.c new file mode 100644 index 000000000000..4276f087f26e --- /dev/null +++ b/arch/powerpc/platforms/82xx/mpc82xx_ads.c @@ -0,0 +1,661 @@ +/* + * MPC82xx_ads setup and early boot code plus other random bits. + * + * Author: Vitaly Bordug <vbordug@ru.mvista.com> + * m82xx_restart fix by Wade Farnsworth <wfarnsworth@mvista.com> + * + * Copyright (c) 2006 MontaVista Software, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + + +#include <linux/config.h> +#include <linux/stddef.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/errno.h> +#include <linux/reboot.h> +#include <linux/pci.h> +#include <linux/interrupt.h> +#include <linux/kdev_t.h> +#include <linux/major.h> +#include <linux/console.h> +#include <linux/delay.h> +#include <linux/seq_file.h> +#include <linux/root_dev.h> +#include <linux/initrd.h> +#include <linux/module.h> +#include <linux/fsl_devices.h> +#include <linux/fs_uart_pd.h> + +#include <asm/system.h> +#include <asm/pgtable.h> +#include <asm/page.h> +#include <asm/atomic.h> +#include <asm/time.h> +#include <asm/io.h> +#include <asm/machdep.h> +#include <asm/bootinfo.h> +#include <asm/pci-bridge.h> +#include <asm/mpc8260.h> +#include <asm/irq.h> +#include <mm/mmu_decl.h> +#include <asm/prom.h> +#include <asm/cpm2.h> +#include <asm/udbg.h> +#include <asm/i8259.h> +#include <linux/fs_enet_pd.h> + +#include <sysdev/fsl_soc.h> +#include <../sysdev/cpm2_pic.h> + +#include "pq2ads_pd.h" + +#ifdef CONFIG_PCI +static uint pci_clk_frq; +static struct { + unsigned long *pci_int_stat_reg; + unsigned long *pci_int_mask_reg; +} pci_regs; + +static unsigned long pci_int_base; +static struct irq_host *pci_pic_host; +static struct device_node *pci_pic_node; +#endif + +static void __init mpc82xx_ads_pic_init(void) +{ + struct device_node *np = of_find_compatible_node(NULL, "cpm-pic", "CPM2"); + struct resource r; + cpm2_map_t *cpm_reg; + + if (np == NULL) { + printk(KERN_ERR "PIC init: can not find cpm-pic node\n"); + return; + } + if (of_address_to_resource(np, 0, &r)) { + printk(KERN_ERR "PIC init: invalid resource\n"); + of_node_put(np); + return; + } + cpm2_pic_init(np); + of_node_put(np); + + /* Initialize the default interrupt mapping priorities, + * in case the boot rom changed something on us. + */ + cpm_reg = (cpm2_map_t *) ioremap(get_immrbase(), sizeof(cpm2_map_t)); + cpm_reg->im_intctl.ic_siprr = 0x05309770; + iounmap(cpm_reg); +#ifdef CONFIG_PCI + /* Initialize stuff for the 82xx CPLD IC and install demux */ + m82xx_pci_init_irq(); +#endif +} + +static void init_fcc1_ioports(struct fs_platform_info *fpi) +{ + struct io_port *io; + u32 tempval; + cpm2_map_t *immap = ioremap(get_immrbase(), sizeof(cpm2_map_t)); + struct device_node *np; + struct resource r; + u32 *bcsr; + + np = of_find_node_by_type(NULL, "memory"); + if (!np) { + printk(KERN_INFO "No memory node in device tree\n"); + return; + } + if (of_address_to_resource(np, 1, &r)) { + printk(KERN_INFO "No memory reg property [1] in devicetree\n"); + return; + } + of_node_put(np); + bcsr = ioremap(r.start + 4, sizeof(u32)); + io = &immap->im_ioport; + + /* Enable the PHY */ + clrbits32(bcsr, BCSR1_FETHIEN); + setbits32(bcsr, BCSR1_FETH_RST); + + /* FCC1 pins are on port A/C. */ + /* Configure port A and C pins for FCC1 Ethernet. */ + + tempval = in_be32(&io->iop_pdira); + tempval &= ~PA1_DIRA0; + tempval |= PA1_DIRA1; + out_be32(&io->iop_pdira, tempval); + + tempval = in_be32(&io->iop_psora); + tempval &= ~PA1_PSORA0; + tempval |= PA1_PSORA1; + out_be32(&io->iop_psora, tempval); + + setbits32(&io->iop_ppara, PA1_DIRA0 | PA1_DIRA1); + + /* Alter clocks */ + tempval = PC_CLK(fpi->clk_tx - 8) | PC_CLK(fpi->clk_rx - 8); + + clrbits32(&io->iop_psorc, tempval); + clrbits32(&io->iop_pdirc, tempval); + setbits32(&io->iop_pparc, tempval); + + cpm2_clk_setup(CPM_CLK_FCC1, fpi->clk_rx, CPM_CLK_RX); + cpm2_clk_setup(CPM_CLK_FCC1, fpi->clk_tx, CPM_CLK_TX); + + iounmap(bcsr); + iounmap(immap); +} + +static void init_fcc2_ioports(struct fs_platform_info *fpi) +{ + cpm2_map_t *immap = ioremap(get_immrbase(), sizeof(cpm2_map_t)); + struct device_node *np; + struct resource r; + u32 *bcsr; + + struct io_port *io; + u32 tempval; + + np = of_find_node_by_type(NULL, "memory"); + if (!np) { + printk(KERN_INFO "No memory node in device tree\n"); + return; + } + if (of_address_to_resource(np, 1, &r)) { + printk(KERN_INFO "No memory reg property [1] in devicetree\n"); + return; + } + of_node_put(np); + io = &immap->im_ioport; + bcsr = ioremap(r.start + 12, sizeof(u32)); + + /* Enable the PHY */ + clrbits32(bcsr, BCSR3_FETHIEN2); + setbits32(bcsr, BCSR3_FETH2_RST); + + /* FCC2 are port B/C. */ + /* Configure port A and C pins for FCC2 Ethernet. */ + + tempval = in_be32(&io->iop_pdirb); + tempval &= ~PB2_DIRB0; + tempval |= PB2_DIRB1; + out_be32(&io->iop_pdirb, tempval); + + tempval = in_be32(&io->iop_psorb); + tempval &= ~PB2_PSORB0; + tempval |= PB2_PSORB1; + out_be32(&io->iop_psorb, tempval); + + setbits32(&io->iop_pparb, PB2_DIRB0 | PB2_DIRB1); + + tempval = PC_CLK(fpi->clk_tx - 8) | PC_CLK(fpi->clk_rx - 8); + + /* Alter clocks */ + clrbits32(&io->iop_psorc, tempval); + clrbits32(&io->iop_pdirc, tempval); + setbits32(&io->iop_pparc, tempval); + + cpm2_clk_setup(CPM_CLK_FCC2, fpi->clk_rx, CPM_CLK_RX); + cpm2_clk_setup(CPM_CLK_FCC2, fpi->clk_tx, CPM_CLK_TX); + + iounmap(bcsr); + iounmap(immap); +} + +void init_fcc_ioports(struct fs_platform_info *fpi) +{ + int fcc_no = fs_get_fcc_index(fpi->fs_no); + + switch (fcc_no) { + case 0: + init_fcc1_ioports(fpi); + break; + case 1: + init_fcc2_ioports(fpi); + break; + default: + printk(KERN_ERR "init_fcc_ioports: invalid FCC number\n"); + return; + } +} + +static void init_scc1_uart_ioports(struct fs_uart_platform_info *data) +{ + cpm2_map_t *immap = ioremap(get_immrbase(), sizeof(cpm2_map_t)); + + /* SCC1 is only on port D */ + setbits32(&immap->im_ioport.iop_ppard, 0x00000003); + clrbits32(&immap->im_ioport.iop_psord, 0x00000001); + setbits32(&immap->im_ioport.iop_psord, 0x00000002); + clrbits32(&immap->im_ioport.iop_pdird, 0x00000001); + setbits32(&immap->im_ioport.iop_pdird, 0x00000002); + + clrbits32(&immap->im_cpmux.cmx_scr, (0x00000007 << (4 - data->clk_tx))); + clrbits32(&immap->im_cpmux.cmx_scr, (0x00000038 << (4 - data->clk_rx))); + setbits32(&immap->im_cpmux.cmx_scr, + ((data->clk_tx - 1) << (4 - data->clk_tx))); + setbits32(&immap->im_cpmux.cmx_scr, + ((data->clk_rx - 1) << (4 - data->clk_rx))); + + iounmap(immap); +} + +static void init_scc4_uart_ioports(struct fs_uart_platform_info *data) +{ + cpm2_map_t *immap = ioremap(get_immrbase(), sizeof(cpm2_map_t)); + + setbits32(&immap->im_ioport.iop_ppard, 0x00000600); + clrbits32(&immap->im_ioport.iop_psord, 0x00000600); + clrbits32(&immap->im_ioport.iop_pdird, 0x00000200); + setbits32(&immap->im_ioport.iop_pdird, 0x00000400); + + clrbits32(&immap->im_cpmux.cmx_scr, (0x00000007 << (4 - data->clk_tx))); + clrbits32(&immap->im_cpmux.cmx_scr, (0x00000038 << (4 - data->clk_rx))); + setbits32(&immap->im_cpmux.cmx_scr, + ((data->clk_tx - 1) << (4 - data->clk_tx))); + setbits32(&immap->im_cpmux.cmx_scr, + ((data->clk_rx - 1) << (4 - data->clk_rx))); + + iounmap(immap); +} + +void init_scc_ioports(struct fs_uart_platform_info *data) +{ + int scc_no = fs_get_scc_index(data->fs_no); + + switch (scc_no) { + case 0: + init_scc1_uart_ioports(data); + data->brg = data->clk_rx; + break; + case 3: + init_scc4_uart_ioports(data); + data->brg = data->clk_rx; + break; + default: + printk(KERN_ERR "init_scc_ioports: invalid SCC number\n"); + return; + } +} + +void __init m82xx_board_setup(void) +{ + cpm2_map_t *immap = ioremap(get_immrbase(), sizeof(cpm2_map_t)); + struct device_node *np; + struct resource r; + u32 *bcsr; + + np = of_find_node_by_type(NULL, "memory"); + if (!np) { + printk(KERN_INFO "No memory node in device tree\n"); + return; + } + if (of_address_to_resource(np, 1, &r)) { + printk(KERN_INFO "No memory reg property [1] in devicetree\n"); + return; + } + of_node_put(np); + bcsr = ioremap(r.start + 4, sizeof(u32)); + /* Enable the 2nd UART port */ + clrbits32(bcsr, BCSR1_RS232_EN2); + +#ifdef CONFIG_SERIAL_CPM_SCC1 + clrbits32((u32 *) & immap->im_scc[0].scc_sccm, + UART_SCCM_TX | UART_SCCM_RX); + clrbits32((u32 *) & immap->im_scc[0].scc_gsmrl, + SCC_GSMRL_ENR | SCC_GSMRL_ENT); +#endif + +#ifdef CONFIG_SERIAL_CPM_SCC2 + clrbits32((u32 *) & immap->im_scc[1].scc_sccm, + UART_SCCM_TX | UART_SCCM_RX); + clrbits32((u32 *) & immap->im_scc[1].scc_gsmrl, + SCC_GSMRL_ENR | SCC_GSMRL_ENT); +#endif + +#ifdef CONFIG_SERIAL_CPM_SCC3 + clrbits32((u32 *) & immap->im_scc[2].scc_sccm, + UART_SCCM_TX | UART_SCCM_RX); + clrbits32((u32 *) & immap->im_scc[2].scc_gsmrl, + SCC_GSMRL_ENR | SCC_GSMRL_ENT); +#endif + +#ifdef CONFIG_SERIAL_CPM_SCC4 + clrbits32((u32 *) & immap->im_scc[3].scc_sccm, + UART_SCCM_TX | UART_SCCM_RX); + clrbits32((u32 *) & immap->im_scc[3].scc_gsmrl, + SCC_GSMRL_ENR | SCC_GSMRL_ENT); +#endif + + iounmap(bcsr); + iounmap(immap); +} + +#ifdef CONFIG_PCI +static void m82xx_pci_mask_irq(unsigned int irq) +{ + int bit = irq - pci_int_base; + + *pci_regs.pci_int_mask_reg |= (1 << (31 - bit)); + return; +} + +static void m82xx_pci_unmask_irq(unsigned int irq) +{ + int bit = irq - pci_int_base; + + *pci_regs.pci_int_mask_reg &= ~(1 << (31 - bit)); + return; +} + +static void m82xx_pci_mask_and_ack(unsigned int irq) +{ + int bit = irq - pci_int_base; + + *pci_regs.pci_int_mask_reg |= (1 << (31 - bit)); + return; +} + +static void m82xx_pci_end_irq(unsigned int irq) +{ + int bit = irq - pci_int_base; + + *pci_regs.pci_int_mask_reg &= ~(1 << (31 - bit)); + return; +} + +struct hw_interrupt_type m82xx_pci_ic = { + .typename = "MPC82xx ADS PCI", + .name = "MPC82xx ADS PCI", + .enable = m82xx_pci_unmask_irq, + .disable = m82xx_pci_mask_irq, + .ack = m82xx_pci_mask_and_ack, + .end = m82xx_pci_end_irq, + .mask = m82xx_pci_mask_irq, + .mask_ack = m82xx_pci_mask_and_ack, + .unmask = m82xx_pci_unmask_irq, + .eoi = m82xx_pci_end_irq, +}; + +static void +m82xx_pci_irq_demux(unsigned int irq, struct irq_desc *desc, + struct pt_regs *regs) +{ + unsigned long stat, mask, pend; + int bit; + + for (;;) { + stat = *pci_regs.pci_int_stat_reg; + mask = *pci_regs.pci_int_mask_reg; + pend = stat & ~mask & 0xf0000000; + if (!pend) + break; + for (bit = 0; pend != 0; ++bit, pend <<= 1) { + if (pend & 0x80000000) + __do_IRQ(pci_int_base + bit, regs); + } + } +} + +static int pci_pic_host_match(struct irq_host *h, struct device_node *node) +{ + return node == pci_pic_node; +} + +static int pci_pic_host_map(struct irq_host *h, unsigned int virq, + irq_hw_number_t hw) +{ + get_irq_desc(virq)->status |= IRQ_LEVEL; + set_irq_chip(virq, &m82xx_pci_ic); + return 0; +} + +static void pci_host_unmap(struct irq_host *h, unsigned int virq) +{ + /* remove chip and handler */ + set_irq_chip(virq, NULL); +} + +static struct irq_host_ops pci_pic_host_ops = { + .match = pci_pic_host_match, + .map = pci_pic_host_map, + .unmap = pci_host_unmap, +}; + +void m82xx_pci_init_irq(void) +{ + int irq; + cpm2_map_t *immap; + struct device_node *np; + struct resource r; + const u32 *regs; + unsigned int size; + const u32 *irq_map; + int i; + unsigned int irq_max, irq_min; + + if ((np = of_find_node_by_type(NULL, "soc")) == NULL) { + printk(KERN_INFO "No SOC node in device tree\n"); + return; + } + memset(&r, 0, sizeof(r)); + if (of_address_to_resource(np, 0, &r)) { + printk(KERN_INFO "No SOC reg property in device tree\n"); + return; + } + immap = ioremap(r.start, sizeof(*immap)); + of_node_put(np); + + /* install the demultiplexer for the PCI cascade interrupt */ + np = of_find_node_by_type(NULL, "pci"); + if (!np) { + printk(KERN_INFO "No pci node on device tree\n"); + iounmap(immap); + return; + } + irq_map = get_property(np, "interrupt-map", &size); + if ((!irq_map) || (size <= 7)) { + printk(KERN_INFO "No interrupt-map property of pci node\n"); + iounmap(immap); + return; + } + size /= sizeof(irq_map[0]); + for (i = 0, irq_max = 0, irq_min = 512; i < size; i += 7, irq_map += 7) { + if (irq_map[5] < irq_min) + irq_min = irq_map[5]; + if (irq_map[5] > irq_max) + irq_max = irq_map[5]; + } + pci_int_base = irq_min; + irq = irq_of_parse_and_map(np, 0); + set_irq_chained_handler(irq, m82xx_pci_irq_demux); + of_node_put(np); + np = of_find_node_by_type(NULL, "pci-pic"); + if (!np) { + printk(KERN_INFO "No pci pic node on device tree\n"); + iounmap(immap); + return; + } + pci_pic_node = of_node_get(np); + /* PCI interrupt controller registers: status and mask */ + regs = get_property(np, "reg", &size); + if ((!regs) || (size <= 2)) { + printk(KERN_INFO "No reg property in pci pic node\n"); + iounmap(immap); + return; + } + pci_regs.pci_int_stat_reg = + ioremap(regs[0], sizeof(*pci_regs.pci_int_stat_reg)); + pci_regs.pci_int_mask_reg = + ioremap(regs[1], sizeof(*pci_regs.pci_int_mask_reg)); + of_node_put(np); + /* configure chip select for PCI interrupt controller */ + immap->im_memctl.memc_br3 = regs[0] | 0x00001801; + immap->im_memctl.memc_or3 = 0xffff8010; + /* make PCI IRQ level sensitive */ + immap->im_intctl.ic_siexr &= ~(1 << (14 - (irq - SIU_INT_IRQ1))); + + /* mask all PCI interrupts */ + *pci_regs.pci_int_mask_reg |= 0xfff00000; + iounmap(immap); + pci_pic_host = + irq_alloc_host(IRQ_HOST_MAP_LINEAR, irq_max - irq_min + 1, + &pci_pic_host_ops, irq_max + 1); + return; +} + +static int m82xx_pci_exclude_device(u_char bus, u_char devfn) +{ + if (bus == 0 && PCI_SLOT(devfn) == 0) + return PCIBIOS_DEVICE_NOT_FOUND; + else + return PCIBIOS_SUCCESSFUL; +} + +static void +__init mpc82xx_pcibios_fixup(void) +{ + struct pci_dev *dev = NULL; + + for_each_pci_dev(dev) { + pci_read_irq_line(dev); + } +} + +void __init add_bridge(struct device_node *np) +{ + int len; + struct pci_controller *hose; + struct resource r; + const int *bus_range; + const void *ptr; + + memset(&r, 0, sizeof(r)); + if (of_address_to_resource(np, 0, &r)) { + printk(KERN_INFO "No PCI reg property in device tree\n"); + return; + } + if (!(ptr = get_property(np, "clock-frequency", NULL))) { + printk(KERN_INFO "No clock-frequency property in PCI node"); + return; + } + pci_clk_frq = *(uint *) ptr; + of_node_put(np); + bus_range = get_property(np, "bus-range", &len); + if (bus_range == NULL || len < 2 * sizeof(int)) { + printk(KERN_WARNING "Can't get bus-range for %s, assume" + " bus 0\n", np->full_name); + } + + pci_assign_all_buses = 1; + + hose = pcibios_alloc_controller(); + + if (!hose) + return; + + hose->arch_data = np; + hose->set_cfg_type = 1; + + hose->first_busno = bus_range ? bus_range[0] : 0; + hose->last_busno = bus_range ? bus_range[1] : 0xff; + hose->bus_offset = 0; + + hose->set_cfg_type = 1; + + setup_indirect_pci(hose, + r.start + offsetof(pci_cpm2_t, pci_cfg_addr), + r.start + offsetof(pci_cpm2_t, pci_cfg_data)); + + pci_process_bridge_OF_ranges(hose, np, 1); +} +#endif + +/* + * Setup the architecture + */ +static void __init mpc82xx_ads_setup_arch(void) +{ +#ifdef CONFIG_PCI + struct device_node *np; +#endif + + if (ppc_md.progress) + ppc_md.progress("mpc82xx_ads_setup_arch()", 0); + cpm2_reset(); + + /* Map I/O region to a 256MB BAT */ + + m82xx_board_setup(); + +#ifdef CONFIG_PCI + ppc_md.pci_exclude_device = m82xx_pci_exclude_device; + for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;) + add_bridge(np); + + of_node_put(np); + ppc_md.pci_map_irq = NULL; + ppc_md.pcibios_fixup = mpc82xx_pcibios_fixup; + ppc_md.pcibios_fixup_bus = NULL; +#endif + +#ifdef CONFIG_ROOT_NFS + ROOT_DEV = Root_NFS; +#else + ROOT_DEV = Root_HDA1; +#endif + + if (ppc_md.progress) + ppc_md.progress("mpc82xx_ads_setup_arch(), finish", 0); +} + +/* + * Called very early, device-tree isn't unflattened + */ +static int __init mpc82xx_ads_probe(void) +{ + /* We always match for now, eventually we should look at + * the flat dev tree to ensure this is the board we are + * supposed to run on + */ + return 1; +} + +#define RMR_CSRE 0x00000001 +static void m82xx_restart(char *cmd) +{ + __volatile__ unsigned char dummy; + + local_irq_disable(); + ((cpm2_map_t *) cpm2_immr)->im_clkrst.car_rmr |= RMR_CSRE; + + /* Clear the ME,EE,IR & DR bits in MSR to cause checkstop */ + mtmsr(mfmsr() & ~(MSR_ME | MSR_EE | MSR_IR | MSR_DR)); + dummy = ((cpm2_map_t *) cpm2_immr)->im_clkrst.res[0]; + printk("Restart failed\n"); + while (1) ; +} + +static void m82xx_halt(void) +{ + local_irq_disable(); + while (1) ; +} + +define_machine(mpc82xx_ads) +{ + .name = "MPC82xx ADS", + .probe = mpc82xx_ads_probe, + .setup_arch = mpc82xx_ads_setup_arch, + .init_IRQ = mpc82xx_ads_pic_init, + .show_cpuinfo = mpc82xx_ads_show_cpuinfo, + .get_irq = cpm2_get_irq, + .calibrate_decr = m82xx_calibrate_decr, + .restart = m82xx_restart,.halt = m82xx_halt, +}; diff --git a/arch/powerpc/platforms/82xx/pq2ads.h b/arch/powerpc/platforms/82xx/pq2ads.h new file mode 100644 index 000000000000..a7348213508f --- /dev/null +++ b/arch/powerpc/platforms/82xx/pq2ads.h @@ -0,0 +1,67 @@ +/* + * PQ2/mpc8260 board-specific stuff + * + * A collection of structures, addresses, and values associated with + * the Freescale MPC8260ADS/MPC8266ADS-PCI boards. + * Copied from the RPX-Classic and SBS8260 stuff. + * + * Author: Vitaly Bordug <vbordug@ru.mvista.com> + * + * Originally written by Dan Malek for Motorola MPC8260 family + * + * Copyright (c) 2001 Dan Malek <dan@embeddedalley.com> + * Copyright (c) 2006 MontaVista Software, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#ifdef __KERNEL__ +#ifndef __MACH_ADS8260_DEFS +#define __MACH_ADS8260_DEFS + +#include <linux/config.h> + +#include <asm/ppcboot.h> + +/* For our show_cpuinfo hooks. */ +#define CPUINFO_VENDOR "Freescale Semiconductor" +#define CPUINFO_MACHINE "PQ2 ADS PowerPC" + +/* Backword-compatibility stuff for the drivers */ +#define CPM_MAP_ADDR ((uint)0xf0000000) +#define CPM_IRQ_OFFSET 0 + +/* The ADS8260 has 16, 32-bit wide control/status registers, accessed + * only on word boundaries. + * Not all are used (yet), or are interesting to us (yet). + */ + +/* Things of interest in the CSR. + */ +#define BCSR0_LED0 ((uint)0x02000000) /* 0 == on */ +#define BCSR0_LED1 ((uint)0x01000000) /* 0 == on */ +#define BCSR1_FETHIEN ((uint)0x08000000) /* 0 == enable*/ +#define BCSR1_FETH_RST ((uint)0x04000000) /* 0 == reset */ +#define BCSR1_RS232_EN1 ((uint)0x02000000) /* 0 ==enable */ +#define BCSR1_RS232_EN2 ((uint)0x01000000) /* 0 ==enable */ +#define BCSR3_FETHIEN2 ((uint)0x10000000) /* 0 == enable*/ +#define BCSR3_FETH2_RS ((uint)0x80000000) /* 0 == reset */ + +/* cpm serial driver works with constants below */ + +#define SIU_INT_SMC1 ((uint)0x04+CPM_IRQ_OFFSET) +#define SIU_INT_SMC2i ((uint)0x05+CPM_IRQ_OFFSET) +#define SIU_INT_SCC1 ((uint)0x28+CPM_IRQ_OFFSET) +#define SIU_INT_SCC2 ((uint)0x29+CPM_IRQ_OFFSET) +#define SIU_INT_SCC3 ((uint)0x2a+CPM_IRQ_OFFSET) +#define SIU_INT_SCC4 ((uint)0x2b+CPM_IRQ_OFFSET) + +void m82xx_pci_init_irq(void); +void mpc82xx_ads_show_cpuinfo(struct seq_file*); +void m82xx_calibrate_decr(void); + +#endif /* __MACH_ADS8260_DEFS */ +#endif /* __KERNEL__ */ diff --git a/arch/powerpc/platforms/83xx/Kconfig b/arch/powerpc/platforms/83xx/Kconfig index 5fe7b7faf45f..0975e94ac7c4 100644 --- a/arch/powerpc/platforms/83xx/Kconfig +++ b/arch/powerpc/platforms/83xx/Kconfig @@ -5,6 +5,13 @@ choice prompt "Machine Type" default MPC834x_SYS +config MPC832x_MDS + bool "Freescale MPC832x MDS" + select DEFAULT_UIMAGE + select QUICC_ENGINE + help + This option enables support for the MPC832x MDS evaluation board. + config MPC834x_SYS bool "Freescale MPC834x SYS" select DEFAULT_UIMAGE @@ -27,6 +34,12 @@ config MPC834x_ITX endchoice +config PPC_MPC832x + bool + select PPC_UDBG_16550 + select PPC_INDIRECT_PCI + default y if MPC832x_MDS + config MPC834x bool select PPC_UDBG_16550 diff --git a/arch/powerpc/platforms/83xx/mpc832x_mds.c b/arch/powerpc/platforms/83xx/mpc832x_mds.c new file mode 100644 index 000000000000..54dea9d42dc9 --- /dev/null +++ b/arch/powerpc/platforms/83xx/mpc832x_mds.c @@ -0,0 +1,215 @@ +/* + * Copyright (C) Freescale Semicondutor, Inc. 2006. All rights reserved. + * + * Description: + * MPC832xE MDS board specific routines. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/stddef.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/errno.h> +#include <linux/reboot.h> +#include <linux/pci.h> +#include <linux/kdev_t.h> +#include <linux/major.h> +#include <linux/console.h> +#include <linux/delay.h> +#include <linux/seq_file.h> +#include <linux/root_dev.h> +#include <linux/initrd.h> + +#include <asm/system.h> +#include <asm/atomic.h> +#include <asm/time.h> +#include <asm/io.h> +#include <asm/machdep.h> +#include <asm/ipic.h> +#include <asm/bootinfo.h> +#include <asm/irq.h> +#include <asm/prom.h> +#include <asm/udbg.h> +#include <sysdev/fsl_soc.h> +#include <asm/qe.h> +#include <asm/qe_ic.h> + +#include "mpc83xx.h" +#include "mpc832x_mds.h" + +#undef DEBUG +#ifdef DEBUG +#define DBG(fmt...) udbg_printf(fmt) +#else +#define DBG(fmt...) +#endif + +#ifndef CONFIG_PCI +unsigned long isa_io_base = 0; +unsigned long isa_mem_base = 0; +#endif + +static u8 *bcsr_regs = NULL; + +u8 *get_bcsr(void) +{ + return bcsr_regs; +} + +/* ************************************************************************ + * + * Setup the architecture + * + */ +static void __init mpc832x_sys_setup_arch(void) +{ + struct device_node *np; + + if (ppc_md.progress) + ppc_md.progress("mpc832x_sys_setup_arch()", 0); + + np = of_find_node_by_type(NULL, "cpu"); + if (np != 0) { + unsigned int *fp = + (int *)get_property(np, "clock-frequency", NULL); + if (fp != 0) + loops_per_jiffy = *fp / HZ; + else + loops_per_jiffy = 50000000 / HZ; + of_node_put(np); + } + + /* Map BCSR area */ + np = of_find_node_by_name(NULL, "bcsr"); + if (np != 0) { + struct resource res; + + of_address_to_resource(np, 0, &res); + bcsr_regs = ioremap(res.start, res.end - res.start +1); + of_node_put(np); + } + +#ifdef CONFIG_PCI + for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;) + add_bridge(np); + + ppc_md.pci_swizzle = common_swizzle; + ppc_md.pci_exclude_device = mpc83xx_exclude_device; +#endif + +#ifdef CONFIG_QUICC_ENGINE + qe_reset(); + + if ((np = of_find_node_by_name(np, "par_io")) != NULL) { + par_io_init(np); + of_node_put(np); + + for (np = NULL; (np = of_find_node_by_name(np, "ucc")) != NULL;) + par_io_of_config(np); + } + + if ((np = of_find_compatible_node(NULL, "network", "ucc_geth")) + != NULL){ + /* Reset the Ethernet PHY */ + bcsr_regs[9] &= ~0x20; + udelay(1000); + bcsr_regs[9] |= 0x20; + iounmap(bcsr_regs); + of_node_put(np); + } + +#endif /* CONFIG_QUICC_ENGINE */ + +#ifdef CONFIG_BLK_DEV_INITRD + if (initrd_start) + ROOT_DEV = Root_RAM0; + else +#endif +#ifdef CONFIG_ROOT_NFS + ROOT_DEV = Root_NFS; +#else + ROOT_DEV = Root_HDA1; +#endif +} + +void __init mpc832x_sys_init_IRQ(void) +{ + + struct device_node *np; + + np = of_find_node_by_type(NULL, "ipic"); + if (!np) + return; + + ipic_init(np, 0); + + /* Initialize the default interrupt mapping priorities, + * in case the boot rom changed something on us. + */ + ipic_set_default_priority(); + of_node_put(np); + +#ifdef CONFIG_QUICC_ENGINE + np = of_find_node_by_type(NULL, "qeic"); + if (!np) + return; + + qe_ic_init(np, 0); + of_node_put(np); +#endif /* CONFIG_QUICC_ENGINE */ +} + +#if defined(CONFIG_I2C_MPC) && defined(CONFIG_SENSORS_DS1374) +extern ulong ds1374_get_rtc_time(void); +extern int ds1374_set_rtc_time(ulong); + +static int __init mpc832x_rtc_hookup(void) +{ + struct timespec tv; + + ppc_md.get_rtc_time = ds1374_get_rtc_time; + ppc_md.set_rtc_time = ds1374_set_rtc_time; + + tv.tv_nsec = 0; + tv.tv_sec = (ppc_md.get_rtc_time) (); + do_settimeofday(&tv); + + return 0; +} + +late_initcall(mpc832x_rtc_hookup); +#endif + +/* + * Called very early, MMU is off, device-tree isn't unflattened + */ +static int __init mpc832x_sys_probe(void) +{ + char *model = of_get_flat_dt_prop(of_get_flat_dt_root(), + "model", NULL); + + if (model == NULL) + return 0; + if (strcmp(model, "MPC8323EMDS")) + return 0; + + DBG("%s found\n", model); + + return 1; +} + +define_machine(mpc832x_mds) { + .name = "MPC832x MDS", + .probe = mpc832x_sys_probe, + .setup_arch = mpc832x_sys_setup_arch, + .init_IRQ = mpc832x_sys_init_IRQ, + .get_irq = ipic_get_irq, + .restart = mpc83xx_restart, + .time_init = mpc83xx_time_init, + .calibrate_decr = generic_calibrate_decr, + .progress = udbg_progress, +}; diff --git a/arch/powerpc/platforms/83xx/mpc832x_mds.h b/arch/powerpc/platforms/83xx/mpc832x_mds.h new file mode 100644 index 000000000000..a49588904f8a --- /dev/null +++ b/arch/powerpc/platforms/83xx/mpc832x_mds.h @@ -0,0 +1,19 @@ +/* + * Copyright (C) Freescale Semicondutor, Inc. 2006. All rights reserved. + * + * Description: + * MPC832x MDS board specific header. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ + +#ifndef __MACH_MPC832x_MDS_H__ +#define __MACH_MPC832x_MDS_H__ + +extern u8 *get_bcsr(void); + +#endif /* __MACH_MPC832x_MDS_H__ */ diff --git a/arch/powerpc/platforms/83xx/mpc8360e_pb.c b/arch/powerpc/platforms/83xx/mpc8360e_pb.c new file mode 100644 index 000000000000..c0191900fc25 --- /dev/null +++ b/arch/powerpc/platforms/83xx/mpc8360e_pb.c @@ -0,0 +1,219 @@ +/* + * Copyright (C) Freescale Semicondutor, Inc. 2006. All rights reserved. + * + * Author: Li Yang <LeoLi@freescale.com> + * Yin Olivia <Hong-hua.Yin@freescale.com> + * + * Description: + * MPC8360E MDS PB board specific routines. + * + * Changelog: + * Jun 21, 2006 Initial version + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/stddef.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/errno.h> +#include <linux/reboot.h> +#include <linux/pci.h> +#include <linux/kdev_t.h> +#include <linux/major.h> +#include <linux/console.h> +#include <linux/delay.h> +#include <linux/seq_file.h> +#include <linux/root_dev.h> +#include <linux/initrd.h> + +#include <asm/system.h> +#include <asm/atomic.h> +#include <asm/time.h> +#include <asm/io.h> +#include <asm/machdep.h> +#include <asm/ipic.h> +#include <asm/bootinfo.h> +#include <asm/irq.h> +#include <asm/prom.h> +#include <asm/udbg.h> +#include <sysdev/fsl_soc.h> +#include <asm/qe.h> +#include <asm/qe_ic.h> + +#include "mpc83xx.h" + +#undef DEBUG +#ifdef DEBUG +#define DBG(fmt...) udbg_printf(fmt) +#else +#define DBG(fmt...) +#endif + +#ifndef CONFIG_PCI +unsigned long isa_io_base = 0; +unsigned long isa_mem_base = 0; +#endif + +static u8 *bcsr_regs = NULL; + +u8 *get_bcsr(void) +{ + return bcsr_regs; +} + +/* ************************************************************************ + * + * Setup the architecture + * + */ +static void __init mpc8360_sys_setup_arch(void) +{ + struct device_node *np; + + if (ppc_md.progress) + ppc_md.progress("mpc8360_sys_setup_arch()", 0); + + np = of_find_node_by_type(NULL, "cpu"); + if (np != 0) { + const unsigned int *fp = + get_property(np, "clock-frequency", NULL); + if (fp != 0) + loops_per_jiffy = *fp / HZ; + else + loops_per_jiffy = 50000000 / HZ; + of_node_put(np); + } + + /* Map BCSR area */ + np = of_find_node_by_name(NULL, "bcsr"); + if (np != 0) { + struct resource res; + + of_address_to_resource(np, 0, &res); + bcsr_regs = ioremap(res.start, res.end - res.start +1); + of_node_put(np); + } + +#ifdef CONFIG_PCI + for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;) + add_bridge(np); + + ppc_md.pci_swizzle = common_swizzle; + ppc_md.pci_exclude_device = mpc83xx_exclude_device; +#endif + +#ifdef CONFIG_QUICC_ENGINE + qe_reset(); + + if ((np = of_find_node_by_name(np, "par_io")) != NULL) { + par_io_init(np); + of_node_put(np); + + for (np = NULL; (np = of_find_node_by_name(np, "ucc")) != NULL;) + par_io_of_config(np); + } + + if ((np = of_find_compatible_node(NULL, "network", "ucc_geth")) + != NULL){ + /* Reset the Ethernet PHY */ + bcsr_regs[9] &= ~0x20; + udelay(1000); + bcsr_regs[9] |= 0x20; + iounmap(bcsr_regs); + of_node_put(np); + } + +#endif /* CONFIG_QUICC_ENGINE */ + +#ifdef CONFIG_BLK_DEV_INITRD + if (initrd_start) + ROOT_DEV = Root_RAM0; + else +#endif +#ifdef CONFIG_ROOT_NFS + ROOT_DEV = Root_NFS; +#else + ROOT_DEV = Root_HDA1; +#endif +} + +void __init mpc8360_sys_init_IRQ(void) +{ + + struct device_node *np; + + np = of_find_node_by_type(NULL, "ipic"); + if (!np) + return; + + ipic_init(np, 0); + + /* Initialize the default interrupt mapping priorities, + * in case the boot rom changed something on us. + */ + ipic_set_default_priority(); + of_node_put(np); + +#ifdef CONFIG_QUICC_ENGINE + np = of_find_node_by_type(NULL, "qeic"); + if (!np) + return; + + qe_ic_init(np, 0); + of_node_put(np); +#endif /* CONFIG_QUICC_ENGINE */ +} + +#if defined(CONFIG_I2C_MPC) && defined(CONFIG_SENSORS_DS1374) +extern ulong ds1374_get_rtc_time(void); +extern int ds1374_set_rtc_time(ulong); + +static int __init mpc8360_rtc_hookup(void) +{ + struct timespec tv; + + ppc_md.get_rtc_time = ds1374_get_rtc_time; + ppc_md.set_rtc_time = ds1374_set_rtc_time; + + tv.tv_nsec = 0; + tv.tv_sec = (ppc_md.get_rtc_time) (); + do_settimeofday(&tv); + + return 0; +} + +late_initcall(mpc8360_rtc_hookup); +#endif + +/* + * Called very early, MMU is off, device-tree isn't unflattened + */ +static int __init mpc8360_sys_probe(void) +{ + char *model = of_get_flat_dt_prop(of_get_flat_dt_root(), + "model", NULL); + if (model == NULL) + return 0; + if (strcmp(model, "MPC8360EPB")) + return 0; + + DBG("MPC8360EMDS-PB found\n"); + + return 1; +} + +define_machine(mpc8360_sys) { + .name = "MPC8360E PB", + .probe = mpc8360_sys_probe, + .setup_arch = mpc8360_sys_setup_arch, + .init_IRQ = mpc8360_sys_init_IRQ, + .get_irq = ipic_get_irq, + .restart = mpc83xx_restart, + .time_init = mpc83xx_time_init, + .calibrate_decr = generic_calibrate_decr, + .progress = udbg_progress, +}; diff --git a/arch/powerpc/platforms/cell/interrupt.c b/arch/powerpc/platforms/cell/interrupt.c index 6b57a47c5d37..6cc59e0b4582 100644 --- a/arch/powerpc/platforms/cell/interrupt.c +++ b/arch/powerpc/platforms/cell/interrupt.c @@ -21,6 +21,12 @@ * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + * TODO: + * - Fix various assumptions related to HW CPU numbers vs. linux CPU numbers + * vs node numbers in the setup code + * - Implement proper handling of maxcpus=1/2 (that is, routing of irqs from + * a non-active node to the active node) */ #include <linux/interrupt.h> @@ -44,24 +50,25 @@ struct iic { u8 target_id; u8 eoi_stack[16]; int eoi_ptr; - struct irq_host *host; + struct device_node *node; }; static DEFINE_PER_CPU(struct iic, iic); #define IIC_NODE_COUNT 2 -static struct irq_host *iic_hosts[IIC_NODE_COUNT]; +static struct irq_host *iic_host; /* Convert between "pending" bits and hw irq number */ static irq_hw_number_t iic_pending_to_hwnum(struct cbe_iic_pending_bits bits) { unsigned char unit = bits.source & 0xf; + unsigned char node = bits.source >> 4; + unsigned char class = bits.class & 3; + /* Decode IPIs */ if (bits.flags & CBE_IIC_IRQ_IPI) - return IIC_IRQ_IPI0 | (bits.prio >> 4); - else if (bits.class <= 3) - return (bits.class << 4) | unit; + return IIC_IRQ_TYPE_IPI | (bits.prio >> 4); else - return IIC_IRQ_INVALID; + return (node << IIC_IRQ_NODE_SHIFT) | (class << 4) | unit; } static void iic_mask(unsigned int irq) @@ -86,21 +93,70 @@ static struct irq_chip iic_chip = { .eoi = iic_eoi, }; + +static void iic_ioexc_eoi(unsigned int irq) +{ +} + +static void iic_ioexc_cascade(unsigned int irq, struct irq_desc *desc, + struct pt_regs *regs) +{ + struct cbe_iic_regs *node_iic = desc->handler_data; + unsigned int base = (irq & 0xffffff00) | IIC_IRQ_TYPE_IOEXC; + unsigned long bits, ack; + int cascade; + + for (;;) { + bits = in_be64(&node_iic->iic_is); + if (bits == 0) + break; + /* pre-ack edge interrupts */ + ack = bits & IIC_ISR_EDGE_MASK; + if (ack) + out_be64(&node_iic->iic_is, ack); + /* handle them */ + for (cascade = 63; cascade >= 0; cascade--) + if (bits & (0x8000000000000000UL >> cascade)) { + unsigned int cirq = + irq_linear_revmap(iic_host, + base | cascade); + if (cirq != NO_IRQ) + generic_handle_irq(cirq, regs); + } + /* post-ack level interrupts */ + ack = bits & ~IIC_ISR_EDGE_MASK; + if (ack) + out_be64(&node_iic->iic_is, ack); + } + desc->chip->eoi(irq); +} + + +static struct irq_chip iic_ioexc_chip = { + .typename = " CELL-IOEX", + .mask = iic_mask, + .unmask = iic_unmask, + .eoi = iic_ioexc_eoi, +}; + /* Get an IRQ number from the pending state register of the IIC */ static unsigned int iic_get_irq(struct pt_regs *regs) { struct cbe_iic_pending_bits pending; struct iic *iic; + unsigned int virq; iic = &__get_cpu_var(iic); *(unsigned long *) &pending = in_be64((unsigned long __iomem *) &iic->regs->pending_destr); + if (!(pending.flags & CBE_IIC_IRQ_VALID)) + return NO_IRQ; + virq = irq_linear_revmap(iic_host, iic_pending_to_hwnum(pending)); + if (virq == NO_IRQ) + return NO_IRQ; iic->eoi_stack[++iic->eoi_ptr] = pending.prio; BUG_ON(iic->eoi_ptr > 15); - if (pending.flags & CBE_IIC_IRQ_VALID) - return irq_linear_revmap(iic->host, - iic_pending_to_hwnum(pending)); - return NO_IRQ; + return virq; } #ifdef CONFIG_SMP @@ -108,12 +164,7 @@ static unsigned int iic_get_irq(struct pt_regs *regs) /* Use the highest interrupt priorities for IPI */ static inline int iic_ipi_to_irq(int ipi) { - return IIC_IRQ_IPI0 + IIC_NUM_IPIS - 1 - ipi; -} - -static inline int iic_irq_to_ipi(int irq) -{ - return IIC_NUM_IPIS - 1 - (irq - IIC_IRQ_IPI0); + return IIC_IRQ_TYPE_IPI + 0xf - ipi; } void iic_setup_cpu(void) @@ -123,7 +174,7 @@ void iic_setup_cpu(void) void iic_cause_IPI(int cpu, int mesg) { - out_be64(&per_cpu(iic, cpu).regs->generate, (IIC_NUM_IPIS - 1 - mesg) << 4); + out_be64(&per_cpu(iic, cpu).regs->generate, (0xf - mesg) << 4); } u8 iic_get_target_id(int cpu) @@ -134,9 +185,7 @@ EXPORT_SYMBOL_GPL(iic_get_target_id); struct irq_host *iic_get_irq_host(int node) { - if (node < 0 || node >= IIC_NODE_COUNT) - return NULL; - return iic_hosts[node]; + return iic_host; } EXPORT_SYMBOL_GPL(iic_get_irq_host); @@ -149,34 +198,20 @@ static irqreturn_t iic_ipi_action(int irq, void *dev_id, struct pt_regs *regs) return IRQ_HANDLED; } - static void iic_request_ipi(int ipi, const char *name) { - int node, virq; + int virq; - for (node = 0; node < IIC_NODE_COUNT; node++) { - char *rname; - if (iic_hosts[node] == NULL) - continue; - virq = irq_create_mapping(iic_hosts[node], - iic_ipi_to_irq(ipi)); - if (virq == NO_IRQ) { - printk(KERN_ERR - "iic: failed to map IPI %s on node %d\n", - name, node); - continue; - } - rname = kzalloc(strlen(name) + 16, GFP_KERNEL); - if (rname) - sprintf(rname, "%s node %d", name, node); - else - rname = (char *)name; - if (request_irq(virq, iic_ipi_action, IRQF_DISABLED, - rname, (void *)(long)ipi)) - printk(KERN_ERR - "iic: failed to request IPI %s on node %d\n", - name, node); + virq = irq_create_mapping(iic_host, iic_ipi_to_irq(ipi)); + if (virq == NO_IRQ) { + printk(KERN_ERR + "iic: failed to map IPI %s\n", name); + return; } + if (request_irq(virq, iic_ipi_action, IRQF_DISABLED, name, + (void *)(long)ipi)) + printk(KERN_ERR + "iic: failed to request IPI %s\n", name); } void iic_request_IPIs(void) @@ -193,16 +228,24 @@ void iic_request_IPIs(void) static int iic_host_match(struct irq_host *h, struct device_node *node) { - return h->host_data != NULL && node == h->host_data; + return device_is_compatible(node, + "IBM,CBEA-Internal-Interrupt-Controller"); } static int iic_host_map(struct irq_host *h, unsigned int virq, irq_hw_number_t hw) { - if (hw < IIC_IRQ_IPI0) - set_irq_chip_and_handler(virq, &iic_chip, handle_fasteoi_irq); - else + switch (hw & IIC_IRQ_TYPE_MASK) { + case IIC_IRQ_TYPE_IPI: set_irq_chip_and_handler(virq, &iic_chip, handle_percpu_irq); + break; + case IIC_IRQ_TYPE_IOEXC: + set_irq_chip_and_handler(virq, &iic_ioexc_chip, + handle_fasteoi_irq); + break; + default: + set_irq_chip_and_handler(virq, &iic_chip, handle_fasteoi_irq); + } return 0; } @@ -211,11 +254,39 @@ static int iic_host_xlate(struct irq_host *h, struct device_node *ct, irq_hw_number_t *out_hwirq, unsigned int *out_flags) { - /* Currently, we don't translate anything. That needs to be fixed as - * we get better defined device-trees. iic interrupts have to be - * explicitely mapped by whoever needs them - */ - return -ENODEV; + unsigned int node, ext, unit, class; + const u32 *val; + + if (!device_is_compatible(ct, + "IBM,CBEA-Internal-Interrupt-Controller")) + return -ENODEV; + if (intsize != 1) + return -ENODEV; + val = get_property(ct, "#interrupt-cells", NULL); + if (val == NULL || *val != 1) + return -ENODEV; + + node = intspec[0] >> 24; + ext = (intspec[0] >> 16) & 0xff; + class = (intspec[0] >> 8) & 0xff; + unit = intspec[0] & 0xff; + + /* Check if node is in supported range */ + if (node > 1) + return -EINVAL; + + /* Build up interrupt number, special case for IO exceptions */ + *out_hwirq = (node << IIC_IRQ_NODE_SHIFT); + if (unit == IIC_UNIT_IIC && class == 1) + *out_hwirq |= IIC_IRQ_TYPE_IOEXC | ext; + else + *out_hwirq |= IIC_IRQ_TYPE_NORMAL | + (class << IIC_IRQ_CLASS_SHIFT) | unit; + + /* Dummy flags, ignored by iic code */ + *out_flags = IRQ_TYPE_EDGE_RISING; + + return 0; } static struct irq_host_ops iic_host_ops = { @@ -225,7 +296,7 @@ static struct irq_host_ops iic_host_ops = { }; static void __init init_one_iic(unsigned int hw_cpu, unsigned long addr, - struct irq_host *host) + struct device_node *node) { /* XXX FIXME: should locate the linux CPU number from the HW cpu * number properly. We are lucky for now @@ -237,19 +308,19 @@ static void __init init_one_iic(unsigned int hw_cpu, unsigned long addr, iic->target_id = ((hw_cpu & 2) << 3) | ((hw_cpu & 1) ? 0xf : 0xe); iic->eoi_stack[0] = 0xff; - iic->host = host; + iic->node = of_node_get(node); out_be64(&iic->regs->prio, 0); - printk(KERN_INFO "IIC for CPU %d at %lx mapped to %p, target id 0x%x\n", - hw_cpu, addr, iic->regs, iic->target_id); + printk(KERN_INFO "IIC for CPU %d target id 0x%x : %s\n", + hw_cpu, iic->target_id, node->full_name); } static int __init setup_iic(void) { struct device_node *dn; struct resource r0, r1; - struct irq_host *host; - int found = 0; + unsigned int node, cascade, found = 0; + struct cbe_iic_regs *node_iic; const u32 *np; for (dn = NULL; @@ -269,19 +340,33 @@ static int __init setup_iic(void) of_node_put(dn); return -ENODEV; } - host = NULL; - if (found < IIC_NODE_COUNT) { - host = irq_alloc_host(IRQ_HOST_MAP_LINEAR, - IIC_SOURCE_COUNT, - &iic_host_ops, - IIC_IRQ_INVALID); - iic_hosts[found] = host; - BUG_ON(iic_hosts[found] == NULL); - iic_hosts[found]->host_data = of_node_get(dn); - found++; - } - init_one_iic(np[0], r0.start, host); - init_one_iic(np[1], r1.start, host); + found++; + init_one_iic(np[0], r0.start, dn); + init_one_iic(np[1], r1.start, dn); + + /* Setup cascade for IO exceptions. XXX cleanup tricks to get + * node vs CPU etc... + * Note that we configure the IIC_IRR here with a hard coded + * priority of 1. We might want to improve that later. + */ + node = np[0] >> 1; + node_iic = cbe_get_cpu_iic_regs(np[0]); + cascade = node << IIC_IRQ_NODE_SHIFT; + cascade |= 1 << IIC_IRQ_CLASS_SHIFT; + cascade |= IIC_UNIT_IIC; + cascade = irq_create_mapping(iic_host, cascade); + if (cascade == NO_IRQ) + continue; + set_irq_data(cascade, node_iic); + set_irq_chained_handler(cascade , iic_ioexc_cascade); + out_be64(&node_iic->iic_ir, + (1 << 12) /* priority */ | + (node << 4) /* dest node */ | + IIC_UNIT_THREAD_0 /* route them to thread 0 */); + /* Flush pending (make sure it triggers if there is + * anything pending + */ + out_be64(&node_iic->iic_is, 0xfffffffffffffffful); } if (found) @@ -292,6 +377,12 @@ static int __init setup_iic(void) void __init iic_init_IRQ(void) { + /* Setup an irq host data structure */ + iic_host = irq_alloc_host(IRQ_HOST_MAP_LINEAR, IIC_SOURCE_COUNT, + &iic_host_ops, IIC_IRQ_INVALID); + BUG_ON(iic_host == NULL); + irq_set_default_host(iic_host); + /* Discover and initialize iics */ if (setup_iic() < 0) panic("IIC: Failed to initialize !\n"); diff --git a/arch/powerpc/platforms/cell/interrupt.h b/arch/powerpc/platforms/cell/interrupt.h index 5560a92ec3ab..9ba1d3c17b4b 100644 --- a/arch/powerpc/platforms/cell/interrupt.h +++ b/arch/powerpc/platforms/cell/interrupt.h @@ -2,48 +2,76 @@ #define ASM_CELL_PIC_H #ifdef __KERNEL__ /* - * Mapping of IIC pending bits into per-node - * interrupt numbers. + * Mapping of IIC pending bits into per-node interrupt numbers. * - * IRQ FF CC SS PP FF CC SS PP Description + * Interrupt numbers are in the range 0...0x1ff where the top bit + * (0x100) represent the source node. Only 2 nodes are supported with + * the current code though it's trivial to extend that if necessary using + * higher level bits * - * 00-3f 80 02 +0 00 - 80 02 +0 3f South Bridge - * 00-3f 80 02 +b 00 - 80 02 +b 3f South Bridge - * 41-4a 80 00 +1 ** - 80 00 +a ** SPU Class 0 - * 51-5a 80 01 +1 ** - 80 01 +a ** SPU Class 1 - * 61-6a 80 02 +1 ** - 80 02 +a ** SPU Class 2 - * 70-7f C0 ** ** 00 - C0 ** ** 0f IPI + * The bottom 8 bits are split into 2 type bits and 6 data bits that + * depend on the type: * - * F flags - * C class - * S source - * P Priority - * + node number - * * don't care + * 00 (0x00 | data) : normal interrupt. data is (class << 4) | source + * 01 (0x40 | data) : IO exception. data is the exception number as + * defined by bit numbers in IIC_SR + * 10 (0x80 | data) : IPI. data is the IPI number (obtained from the priority) + * and node is always 0 (IPIs are per-cpu, their source is + * not relevant) + * 11 (0xc0 | data) : reserved * - * A node consists of a Cell Broadband Engine and an optional - * south bridge device providing a maximum of 64 IRQs. - * The south bridge may be connected to either IOIF0 - * or IOIF1. - * Each SPE is represented as three IRQ lines, one per - * interrupt class. - * 16 IRQ numbers are reserved for inter processor - * interruptions, although these are only used in the - * range of the first node. + * In addition, interrupt number 0x80000000 is defined as always invalid + * (that is the node field is expected to never extend to move than 23 bits) * - * This scheme needs 128 IRQ numbers per BIF node ID, - * which means that with the total of 512 lines - * available, we can have a maximum of four nodes. */ enum { - IIC_IRQ_INVALID = 0xff, - IIC_IRQ_MAX = 0x3f, - IIC_IRQ_EXT_IOIF0 = 0x20, - IIC_IRQ_EXT_IOIF1 = 0x2b, - IIC_IRQ_IPI0 = 0x40, - IIC_NUM_IPIS = 0x10, /* IRQs reserved for IPI */ - IIC_SOURCE_COUNT = 0x50, + IIC_IRQ_INVALID = 0x80000000u, + IIC_IRQ_NODE_MASK = 0x100, + IIC_IRQ_NODE_SHIFT = 8, + IIC_IRQ_MAX = 0x1ff, + IIC_IRQ_TYPE_MASK = 0xc0, + IIC_IRQ_TYPE_NORMAL = 0x00, + IIC_IRQ_TYPE_IOEXC = 0x40, + IIC_IRQ_TYPE_IPI = 0x80, + IIC_IRQ_CLASS_SHIFT = 4, + IIC_IRQ_CLASS_0 = 0x00, + IIC_IRQ_CLASS_1 = 0x10, + IIC_IRQ_CLASS_2 = 0x20, + IIC_SOURCE_COUNT = 0x200, + + /* Here are defined the various source/dest units. Avoid using those + * definitions if you can, they are mostly here for reference + */ + IIC_UNIT_SPU_0 = 0x4, + IIC_UNIT_SPU_1 = 0x7, + IIC_UNIT_SPU_2 = 0x3, + IIC_UNIT_SPU_3 = 0x8, + IIC_UNIT_SPU_4 = 0x2, + IIC_UNIT_SPU_5 = 0x9, + IIC_UNIT_SPU_6 = 0x1, + IIC_UNIT_SPU_7 = 0xa, + IIC_UNIT_IOC_0 = 0x0, + IIC_UNIT_IOC_1 = 0xb, + IIC_UNIT_THREAD_0 = 0xe, /* target only */ + IIC_UNIT_THREAD_1 = 0xf, /* target only */ + IIC_UNIT_IIC = 0xe, /* source only (IO exceptions) */ + + /* Base numbers for the external interrupts */ + IIC_IRQ_EXT_IOIF0 = + IIC_IRQ_TYPE_NORMAL | IIC_IRQ_CLASS_2 | IIC_UNIT_IOC_0, + IIC_IRQ_EXT_IOIF1 = + IIC_IRQ_TYPE_NORMAL | IIC_IRQ_CLASS_2 | IIC_UNIT_IOC_1, + + /* Base numbers for the IIC_ISR interrupts */ + IIC_IRQ_IOEX_TMI = IIC_IRQ_TYPE_IOEXC | IIC_IRQ_CLASS_1 | 63, + IIC_IRQ_IOEX_PMI = IIC_IRQ_TYPE_IOEXC | IIC_IRQ_CLASS_1 | 62, + IIC_IRQ_IOEX_ATI = IIC_IRQ_TYPE_IOEXC | IIC_IRQ_CLASS_1 | 61, + IIC_IRQ_IOEX_MATBFI = IIC_IRQ_TYPE_IOEXC | IIC_IRQ_CLASS_1 | 60, + IIC_IRQ_IOEX_ELDI = IIC_IRQ_TYPE_IOEXC | IIC_IRQ_CLASS_1 | 59, + + /* Which bits in IIC_ISR are edge sensitive */ + IIC_ISR_EDGE_MASK = 0x4ul, }; extern void iic_init_IRQ(void); @@ -52,7 +80,6 @@ extern void iic_request_IPIs(void); extern void iic_setup_cpu(void); extern u8 iic_get_target_id(int cpu); -extern struct irq_host *iic_get_irq_host(int node); extern void spider_init_IRQ(void); diff --git a/arch/powerpc/platforms/cell/spider-pic.c b/arch/powerpc/platforms/cell/spider-pic.c index 742a03282b44..608b1ebc56b2 100644 --- a/arch/powerpc/platforms/cell/spider-pic.c +++ b/arch/powerpc/platforms/cell/spider-pic.c @@ -243,7 +243,6 @@ static unsigned int __init spider_find_cascade_and_node(struct spider_pic *pic) const u32 *imap, *tmp; int imaplen, intsize, unit; struct device_node *iic; - struct irq_host *iic_host; #if 0 /* Enable that when we have a way to retreive the node as well */ /* First, we check wether we have a real "interrupts" in the device @@ -289,11 +288,11 @@ static unsigned int __init spider_find_cascade_and_node(struct spider_pic *pic) * the iic host from the iic OF node, but that way I'm still compatible * with really really old old firmwares for which we don't have a node */ - iic_host = iic_get_irq_host(pic->node_id); - if (iic_host == NULL) - return NO_IRQ; /* Manufacture an IIC interrupt number of class 2 */ - virq = irq_create_mapping(iic_host, 0x20 | unit); + virq = irq_create_mapping(NULL, + (pic->node_id << IIC_IRQ_NODE_SHIFT) | + (2 << IIC_IRQ_CLASS_SHIFT) | + unit); if (virq == NO_IRQ) printk(KERN_ERR "spider_pic: failed to map cascade !"); return virq; diff --git a/arch/powerpc/platforms/cell/spu_base.c b/arch/powerpc/platforms/cell/spu_base.c index 0f5c8ebc7fc3..f78680346e5f 100644 --- a/arch/powerpc/platforms/cell/spu_base.c +++ b/arch/powerpc/platforms/cell/spu_base.c @@ -568,24 +568,23 @@ static void spu_unmap(struct spu *spu) /* This function shall be abstracted for HV platforms */ static int __init spu_map_interrupts(struct spu *spu, struct device_node *np) { - struct irq_host *host; unsigned int isrc; const u32 *tmp; - host = iic_get_irq_host(spu->node); - if (host == NULL) - return -ENODEV; - - /* Get the interrupt source from the device-tree */ + /* Get the interrupt source unit from the device-tree */ tmp = get_property(np, "isrc", NULL); if (!tmp) return -ENODEV; - spu->isrc = isrc = tmp[0]; + isrc = tmp[0]; + + /* Add the node number */ + isrc |= spu->node << IIC_IRQ_NODE_SHIFT; + spu->isrc = isrc; /* Now map interrupts of all 3 classes */ - spu->irqs[0] = irq_create_mapping(host, 0x00 | isrc); - spu->irqs[1] = irq_create_mapping(host, 0x10 | isrc); - spu->irqs[2] = irq_create_mapping(host, 0x20 | isrc); + spu->irqs[0] = irq_create_mapping(NULL, IIC_IRQ_CLASS_0 | isrc); + spu->irqs[1] = irq_create_mapping(NULL, IIC_IRQ_CLASS_1 | isrc); + spu->irqs[2] = irq_create_mapping(NULL, IIC_IRQ_CLASS_2 | isrc); /* Right now, we only fail if class 2 failed */ return spu->irqs[2] == NO_IRQ ? -EINVAL : 0; diff --git a/arch/powerpc/platforms/iseries/pci.c b/arch/powerpc/platforms/iseries/pci.c index 3eb12065df23..4aa165e010d9 100644 --- a/arch/powerpc/platforms/iseries/pci.c +++ b/arch/powerpc/platforms/iseries/pci.c @@ -262,14 +262,6 @@ void __init iSeries_pci_final_fixup(void) mf_display_src(0xC9000200); } -void pcibios_fixup_bus(struct pci_bus *PciBus) -{ -} - -void pcibios_fixup_resources(struct pci_dev *pdev) -{ -} - /* * Look down the chain to find the matching Device Device */ diff --git a/arch/powerpc/platforms/iseries/setup.c b/arch/powerpc/platforms/iseries/setup.c index 7f1953066ff8..a0ff7ba7d666 100644 --- a/arch/powerpc/platforms/iseries/setup.c +++ b/arch/powerpc/platforms/iseries/setup.c @@ -649,15 +649,21 @@ static void iseries_dedicated_idle(void) void __init iSeries_init_IRQ(void) { } #endif +/* + * iSeries has no legacy IO, anything calling this function has to + * fail or bad things will happen + */ +static int iseries_check_legacy_ioport(unsigned int baseport) +{ + return -ENODEV; +} + static int __init iseries_probe(void) { unsigned long root = of_get_flat_dt_root(); if (!of_flat_dt_is_compatible(root, "IBM,iSeries")) return 0; - powerpc_firmware_features |= FW_FEATURE_ISERIES; - powerpc_firmware_features |= FW_FEATURE_LPAR; - hpte_init_iSeries(); return 1; @@ -680,6 +686,7 @@ define_machine(iseries) { .calibrate_decr = generic_calibrate_decr, .progress = iSeries_progress, .probe = iseries_probe, + .check_legacy_ioport = iseries_check_legacy_ioport, /* XXX Implement enable_pmcs for iSeries */ }; @@ -687,6 +694,9 @@ void * __init iSeries_early_setup(void) { unsigned long phys_mem_size; + powerpc_firmware_features |= FW_FEATURE_ISERIES; + powerpc_firmware_features |= FW_FEATURE_LPAR; + iSeries_fixup_klimit(); /* diff --git a/arch/powerpc/platforms/powermac/udbg_scc.c b/arch/powerpc/platforms/powermac/udbg_scc.c index ce1a235855f7..379db05b0082 100644 --- a/arch/powerpc/platforms/powermac/udbg_scc.c +++ b/arch/powerpc/platforms/powermac/udbg_scc.c @@ -111,8 +111,6 @@ void udbg_scc_init(int force_scc) pmac_call_feature(PMAC_FTR_SCC_ENABLE, ch, PMAC_SCC_ASYNC | PMAC_SCC_FLAG_XMON, 1); - - /* Setup for 57600 8N1 */ if (ch == ch_a) addr += 0x20; sccc = ioremap(addr & PAGE_MASK, PAGE_SIZE) ; @@ -125,9 +123,21 @@ void udbg_scc_init(int force_scc) x = in_8(sccc); out_8(sccc, 0x09); /* reset A or B side */ out_8(sccc, 0xc0); + + /* If SCC was the OF output port, read the BRG value, else + * Setup for 57600 8N1 + */ + if (ch_def != NULL) { + out_8(sccc, 13); + scc_inittab[1] = in_8(sccc); + out_8(sccc, 12); + scc_inittab[3] = in_8(sccc); + } + for (i = 0; i < sizeof(scc_inittab); ++i) out_8(sccc, scc_inittab[i]); + udbg_putc = udbg_scc_putc; udbg_getc = udbg_scc_getc; udbg_getc_poll = udbg_scc_getc_poll; diff --git a/arch/powerpc/platforms/pseries/setup.c b/arch/powerpc/platforms/pseries/setup.c index 43dbf737698c..f82b13e531a3 100644 --- a/arch/powerpc/platforms/pseries/setup.c +++ b/arch/powerpc/platforms/pseries/setup.c @@ -180,7 +180,7 @@ static void __init pseries_mpic_init_IRQ(void) cascade_irq = irq_of_parse_and_map(cascade, 0); if (cascade == NO_IRQ) { - printk(KERN_ERR "xics: failed to map cascade interrupt"); + printk(KERN_ERR "mpic: failed to map cascade interrupt"); return; } diff --git a/arch/powerpc/sysdev/Makefile b/arch/powerpc/sysdev/Makefile index f15f4d78aee9..91f052d8cce0 100644 --- a/arch/powerpc/sysdev/Makefile +++ b/arch/powerpc/sysdev/Makefile @@ -12,6 +12,7 @@ obj-$(CONFIG_MMIO_NVRAM) += mmio_nvram.o obj-$(CONFIG_FSL_SOC) += fsl_soc.o obj-$(CONFIG_PPC_TODC) += todc.o obj-$(CONFIG_TSI108_BRIDGE) += tsi108_pci.o tsi108_dev.o +obj-$(CONFIG_QUICC_ENGINE) += qe_lib/ ifeq ($(CONFIG_PPC_MERGE),y) obj-$(CONFIG_PPC_I8259) += i8259.o diff --git a/arch/powerpc/sysdev/cpm2_pic.c b/arch/powerpc/sysdev/cpm2_pic.c index 51752990f7b9..28b018994746 100644 --- a/arch/powerpc/sysdev/cpm2_pic.c +++ b/arch/powerpc/sysdev/cpm2_pic.c @@ -147,7 +147,7 @@ static struct irq_chip cpm2_pic = { .end = cpm2_end_irq, }; -int cpm2_get_irq(struct pt_regs *regs) +unsigned int cpm2_get_irq(struct pt_regs *regs) { int irq; unsigned long bits; diff --git a/arch/powerpc/sysdev/cpm2_pic.h b/arch/powerpc/sysdev/cpm2_pic.h index d63e45d4df58..3c513e5a688e 100644 --- a/arch/powerpc/sysdev/cpm2_pic.h +++ b/arch/powerpc/sysdev/cpm2_pic.h @@ -3,7 +3,7 @@ extern intctl_cpm2_t *cpm2_intctl; -extern int cpm2_get_irq(struct pt_regs *regs); +extern unsigned int cpm2_get_irq(struct pt_regs *regs); extern void cpm2_pic_init(struct device_node*); diff --git a/arch/powerpc/sysdev/fsl_soc.c b/arch/powerpc/sysdev/fsl_soc.c index 022ed275ea68..7d759f1c26b1 100644 --- a/arch/powerpc/sysdev/fsl_soc.c +++ b/arch/powerpc/sysdev/fsl_soc.c @@ -37,6 +37,7 @@ #include <asm/cpm2.h> extern void init_fcc_ioports(struct fs_platform_info*); +extern void init_scc_ioports(struct fs_uart_platform_info*); static phys_addr_t immrbase = -1; phys_addr_t get_immrbase(void) @@ -566,7 +567,7 @@ static int __init fs_enet_of_init(void) struct resource r[4]; struct device_node *phy, *mdio; struct fs_platform_info fs_enet_data; - const unsigned int *id, *phy_addr; + const unsigned int *id, *phy_addr, phy_irq; const void *mac_addr; const phandle *ph; const char *model; @@ -588,6 +589,7 @@ static int __init fs_enet_of_init(void) if (ret) goto err; r[2].name = fcc_regs_c; + fs_enet_data.fcc_regs_c = r[2].start; r[3].start = r[3].end = irq_of_parse_and_map(np, 0); r[3].flags = IORESOURCE_IRQ; @@ -620,6 +622,8 @@ static int __init fs_enet_of_init(void) phy_addr = get_property(phy, "reg", NULL); fs_enet_data.phy_addr = *phy_addr; + phy_irq = get_property(phy, "interrupts", NULL); + id = get_property(np, "device-id", NULL); fs_enet_data.fs_no = *id; strcpy(fs_enet_data.fs_type, model); @@ -637,6 +641,7 @@ static int __init fs_enet_of_init(void) if (strstr(model, "FCC")) { int fcc_index = *id - 1; + unsigned char* mdio_bb_prop; fs_enet_data.dpram_offset = (u32)cpm_dpram_addr(0); fs_enet_data.rx_ring = 32; @@ -652,14 +657,57 @@ static int __init fs_enet_of_init(void) (u32)res.start, fs_enet_data.phy_addr); fs_enet_data.bus_id = (char*)&bus_id[(*id)]; fs_enet_data.init_ioports = init_fcc_ioports; - } - of_node_put(phy); - of_node_put(mdio); + mdio_bb_prop = get_property(phy, "bitbang", NULL); + if (mdio_bb_prop) { + struct platform_device *fs_enet_mdio_bb_dev; + struct fs_mii_bb_platform_info fs_enet_mdio_bb_data; + + fs_enet_mdio_bb_dev = + platform_device_register_simple("fsl-bb-mdio", + i, NULL, 0); + memset(&fs_enet_mdio_bb_data, 0, + sizeof(struct fs_mii_bb_platform_info)); + fs_enet_mdio_bb_data.mdio_dat.bit = + mdio_bb_prop[0]; + fs_enet_mdio_bb_data.mdio_dir.bit = + mdio_bb_prop[1]; + fs_enet_mdio_bb_data.mdc_dat.bit = + mdio_bb_prop[2]; + fs_enet_mdio_bb_data.mdio_port = + mdio_bb_prop[3]; + fs_enet_mdio_bb_data.mdc_port = + mdio_bb_prop[4]; + fs_enet_mdio_bb_data.delay = + mdio_bb_prop[5]; + + fs_enet_mdio_bb_data.irq[0] = phy_irq[0]; + fs_enet_mdio_bb_data.irq[1] = -1; + fs_enet_mdio_bb_data.irq[2] = -1; + fs_enet_mdio_bb_data.irq[3] = phy_irq[0]; + fs_enet_mdio_bb_data.irq[31] = -1; + + fs_enet_mdio_bb_data.mdio_dat.offset = + (u32)&cpm2_immr->im_ioport.iop_pdatc; + fs_enet_mdio_bb_data.mdio_dir.offset = + (u32)&cpm2_immr->im_ioport.iop_pdirc; + fs_enet_mdio_bb_data.mdc_dat.offset = + (u32)&cpm2_immr->im_ioport.iop_pdatc; + + ret = platform_device_add_data( + fs_enet_mdio_bb_dev, + &fs_enet_mdio_bb_data, + sizeof(struct fs_mii_bb_platform_info)); + if (ret) + goto unreg; + } + + of_node_put(phy); + of_node_put(mdio); - ret = platform_device_add_data(fs_enet_dev, &fs_enet_data, - sizeof(struct - fs_platform_info)); + ret = platform_device_add_data(fs_enet_dev, &fs_enet_data, + sizeof(struct + fs_platform_info)); if (ret) goto unreg; } diff --git a/arch/powerpc/sysdev/qe_lib/Kconfig b/arch/powerpc/sysdev/qe_lib/Kconfig new file mode 100644 index 000000000000..a725e80befa8 --- /dev/null +++ b/arch/powerpc/sysdev/qe_lib/Kconfig @@ -0,0 +1,30 @@ +# +# QE Communication options +# + +menu "QE Options" + depends on QUICC_ENGINE + +config UCC_SLOW + bool "UCC Slow Protocols Support" + default n + select UCC + help + This option provides qe_lib support to UCC slow + protocols: UART, BISYNC, QMC + +config UCC_FAST + bool "UCC Fast Protocols Support" + default n + select UCC + select UCC_SLOW + help + This option provides qe_lib support to UCC fast + protocols: HDLC, Ethernet, ATM, transparent + +config UCC + bool + default y if UCC_FAST || UCC_SLOW + +endmenu + diff --git a/arch/powerpc/sysdev/qe_lib/Makefile b/arch/powerpc/sysdev/qe_lib/Makefile new file mode 100644 index 000000000000..874fe1a5b1cf --- /dev/null +++ b/arch/powerpc/sysdev/qe_lib/Makefile @@ -0,0 +1,8 @@ +# +# Makefile for the linux ppc-specific parts of QE +# +obj-$(CONFIG_QUICC_ENGINE)+= qe.o qe_ic.o qe_io.o + +obj-$(CONFIG_UCC) += ucc.o +obj-$(CONFIG_UCC_SLOW) += ucc_slow.o +obj-$(CONFIG_UCC_FAST) += ucc_fast.o diff --git a/arch/powerpc/sysdev/qe_lib/qe.c b/arch/powerpc/sysdev/qe_lib/qe.c new file mode 100644 index 000000000000..2bae632d3ad7 --- /dev/null +++ b/arch/powerpc/sysdev/qe_lib/qe.c @@ -0,0 +1,353 @@ +/* + * Copyright (C) 2006 Freescale Semicondutor, Inc. All rights reserved. + * + * Authors: Shlomi Gridish <gridish@freescale.com> + * Li Yang <leoli@freescale.com> + * Based on cpm2_common.c from Dan Malek (dmalek@jlc.net) + * + * Description: + * General Purpose functions for the global management of the + * QUICC Engine (QE). + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#include <linux/errno.h> +#include <linux/sched.h> +#include <linux/kernel.h> +#include <linux/param.h> +#include <linux/string.h> +#include <linux/mm.h> +#include <linux/interrupt.h> +#include <linux/bootmem.h> +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/ioport.h> +#include <asm/irq.h> +#include <asm/page.h> +#include <asm/pgtable.h> +#include <asm/immap_qe.h> +#include <asm/qe.h> +#include <asm/prom.h> +#include <asm/rheap.h> + +static void qe_snums_init(void); +static void qe_muram_init(void); +static int qe_sdma_init(void); + +static DEFINE_SPINLOCK(qe_lock); + +/* QE snum state */ +enum qe_snum_state { + QE_SNUM_STATE_USED, + QE_SNUM_STATE_FREE +}; + +/* QE snum */ +struct qe_snum { + u8 num; + enum qe_snum_state state; +}; + +/* We allocate this here because it is used almost exclusively for + * the communication processor devices. + */ +struct qe_immap *qe_immr = NULL; +EXPORT_SYMBOL(qe_immr); + +static struct qe_snum snums[QE_NUM_OF_SNUM]; /* Dynamically allocated SNUMs */ + +static phys_addr_t qebase = -1; + +phys_addr_t get_qe_base(void) +{ + struct device_node *qe; + + if (qebase != -1) + return qebase; + + qe = of_find_node_by_type(NULL, "qe"); + if (qe) { + unsigned int size; + const void *prop = get_property(qe, "reg", &size); + qebase = of_translate_address(qe, prop); + of_node_put(qe); + }; + + return qebase; +} + +EXPORT_SYMBOL(get_qe_base); + +void qe_reset(void) +{ + if (qe_immr == NULL) + qe_immr = ioremap(get_qe_base(), QE_IMMAP_SIZE); + + qe_snums_init(); + + qe_issue_cmd(QE_RESET, QE_CR_SUBBLOCK_INVALID, + QE_CR_PROTOCOL_UNSPECIFIED, 0); + + /* Reclaim the MURAM memory for our use. */ + qe_muram_init(); + + if (qe_sdma_init()) + panic("sdma init failed!"); +} + +int qe_issue_cmd(u32 cmd, u32 device, u8 mcn_protocol, u32 cmd_input) +{ + unsigned long flags; + u8 mcn_shift = 0, dev_shift = 0; + + spin_lock_irqsave(&qe_lock, flags); + if (cmd == QE_RESET) { + out_be32(&qe_immr->cp.cecr, (u32) (cmd | QE_CR_FLG)); + } else { + if (cmd == QE_ASSIGN_PAGE) { + /* Here device is the SNUM, not sub-block */ + dev_shift = QE_CR_SNUM_SHIFT; + } else if (cmd == QE_ASSIGN_RISC) { + /* Here device is the SNUM, and mcnProtocol is + * e_QeCmdRiscAssignment value */ + dev_shift = QE_CR_SNUM_SHIFT; + mcn_shift = QE_CR_MCN_RISC_ASSIGN_SHIFT; + } else { + if (device == QE_CR_SUBBLOCK_USB) + mcn_shift = QE_CR_MCN_USB_SHIFT; + else + mcn_shift = QE_CR_MCN_NORMAL_SHIFT; + } + + out_be32(&qe_immr->cp.cecdr, + immrbar_virt_to_phys((void *)cmd_input)); + out_be32(&qe_immr->cp.cecr, + (cmd | QE_CR_FLG | ((u32) device << dev_shift) | (u32) + mcn_protocol << mcn_shift)); + } + + /* wait for the QE_CR_FLG to clear */ + while(in_be32(&qe_immr->cp.cecr) & QE_CR_FLG) + cpu_relax(); + spin_unlock_irqrestore(&qe_lock, flags); + + return 0; +} +EXPORT_SYMBOL(qe_issue_cmd); + +/* Set a baud rate generator. This needs lots of work. There are + * 16 BRGs, which can be connected to the QE channels or output + * as clocks. The BRGs are in two different block of internal + * memory mapped space. + * The baud rate clock is the system clock divided by something. + * It was set up long ago during the initial boot phase and is + * is given to us. + * Baud rate clocks are zero-based in the driver code (as that maps + * to port numbers). Documentation uses 1-based numbering. + */ +static unsigned int brg_clk = 0; + +unsigned int get_brg_clk(void) +{ + struct device_node *qe; + if (brg_clk) + return brg_clk; + + qe = of_find_node_by_type(NULL, "qe"); + if (qe) { + unsigned int size; + const u32 *prop = get_property(qe, "brg-frequency", &size); + brg_clk = *prop; + of_node_put(qe); + }; + return brg_clk; +} + +/* This function is used by UARTS, or anything else that uses a 16x + * oversampled clock. + */ +void qe_setbrg(u32 brg, u32 rate) +{ + volatile u32 *bp; + u32 divisor, tempval; + int div16 = 0; + + bp = &qe_immr->brg.brgc1; + bp += brg; + + divisor = (get_brg_clk() / rate); + if (divisor > QE_BRGC_DIVISOR_MAX + 1) { + div16 = 1; + divisor /= 16; + } + + tempval = ((divisor - 1) << QE_BRGC_DIVISOR_SHIFT) | QE_BRGC_ENABLE; + if (div16) + tempval |= QE_BRGC_DIV16; + + out_be32(bp, tempval); +} + +/* Initialize SNUMs (thread serial numbers) according to + * QE Module Control chapter, SNUM table + */ +static void qe_snums_init(void) +{ + int i; + static const u8 snum_init[] = { + 0x04, 0x05, 0x0C, 0x0D, 0x14, 0x15, 0x1C, 0x1D, + 0x24, 0x25, 0x2C, 0x2D, 0x34, 0x35, 0x88, 0x89, + 0x98, 0x99, 0xA8, 0xA9, 0xB8, 0xB9, 0xC8, 0xC9, + 0xD8, 0xD9, 0xE8, 0xE9, + }; + + for (i = 0; i < QE_NUM_OF_SNUM; i++) { + snums[i].num = snum_init[i]; + snums[i].state = QE_SNUM_STATE_FREE; + } +} + +int qe_get_snum(void) +{ + unsigned long flags; + int snum = -EBUSY; + int i; + + spin_lock_irqsave(&qe_lock, flags); + for (i = 0; i < QE_NUM_OF_SNUM; i++) { + if (snums[i].state == QE_SNUM_STATE_FREE) { + snums[i].state = QE_SNUM_STATE_USED; + snum = snums[i].num; + break; + } + } + spin_unlock_irqrestore(&qe_lock, flags); + + return snum; +} +EXPORT_SYMBOL(qe_get_snum); + +void qe_put_snum(u8 snum) +{ + int i; + + for (i = 0; i < QE_NUM_OF_SNUM; i++) { + if (snums[i].num == snum) { + snums[i].state = QE_SNUM_STATE_FREE; + break; + } + } +} +EXPORT_SYMBOL(qe_put_snum); + +static int qe_sdma_init(void) +{ + struct sdma *sdma = &qe_immr->sdma; + u32 sdma_buf_offset; + + if (!sdma) + return -ENODEV; + + /* allocate 2 internal temporary buffers (512 bytes size each) for + * the SDMA */ + sdma_buf_offset = qe_muram_alloc(512 * 2, 64); + if (IS_MURAM_ERR(sdma_buf_offset)) + return -ENOMEM; + + out_be32(&sdma->sdebcr, sdma_buf_offset & QE_SDEBCR_BA_MASK); + out_be32(&sdma->sdmr, (QE_SDMR_GLB_1_MSK | (0x1 >> + QE_SDMR_CEN_SHIFT))); + + return 0; +} + +/* + * muram_alloc / muram_free bits. + */ +static DEFINE_SPINLOCK(qe_muram_lock); + +/* 16 blocks should be enough to satisfy all requests + * until the memory subsystem goes up... */ +static rh_block_t qe_boot_muram_rh_block[16]; +static rh_info_t qe_muram_info; + +static void qe_muram_init(void) +{ + struct device_node *np; + u32 address; + u64 size; + unsigned int flags; + + /* initialize the info header */ + rh_init(&qe_muram_info, 1, + sizeof(qe_boot_muram_rh_block) / + sizeof(qe_boot_muram_rh_block[0]), qe_boot_muram_rh_block); + + /* Attach the usable muram area */ + /* XXX: This is a subset of the available muram. It + * varies with the processor and the microcode patches activated. + */ + if ((np = of_find_node_by_name(NULL, "data-only")) != NULL) { + address = *of_get_address(np, 0, &size, &flags); + of_node_put(np); + rh_attach_region(&qe_muram_info, + (void *)address, (int)size); + } +} + +/* This function returns an index into the MURAM area. + */ +u32 qe_muram_alloc(u32 size, u32 align) +{ + void *start; + unsigned long flags; + + spin_lock_irqsave(&qe_muram_lock, flags); + start = rh_alloc_align(&qe_muram_info, size, align, "QE"); + spin_unlock_irqrestore(&qe_muram_lock, flags); + + return (u32) start; +} +EXPORT_SYMBOL(qe_muram_alloc); + +int qe_muram_free(u32 offset) +{ + int ret; + unsigned long flags; + + spin_lock_irqsave(&qe_muram_lock, flags); + ret = rh_free(&qe_muram_info, (void *)offset); + spin_unlock_irqrestore(&qe_muram_lock, flags); + + return ret; +} +EXPORT_SYMBOL(qe_muram_free); + +/* not sure if this is ever needed */ +u32 qe_muram_alloc_fixed(u32 offset, u32 size) +{ + void *start; + unsigned long flags; + + spin_lock_irqsave(&qe_muram_lock, flags); + start = rh_alloc_fixed(&qe_muram_info, (void *)offset, size, "commproc"); + spin_unlock_irqrestore(&qe_muram_lock, flags); + + return (u32) start; +} +EXPORT_SYMBOL(qe_muram_alloc_fixed); + +void qe_muram_dump(void) +{ + rh_dump(&qe_muram_info); +} +EXPORT_SYMBOL(qe_muram_dump); + +void *qe_muram_addr(u32 offset) +{ + return (void *)&qe_immr->muram[offset]; +} +EXPORT_SYMBOL(qe_muram_addr); diff --git a/arch/powerpc/sysdev/qe_lib/qe_ic.c b/arch/powerpc/sysdev/qe_lib/qe_ic.c new file mode 100644 index 000000000000..c229d07d4957 --- /dev/null +++ b/arch/powerpc/sysdev/qe_lib/qe_ic.c @@ -0,0 +1,555 @@ +/* + * arch/powerpc/sysdev/qe_lib/qe_ic.c + * + * Copyright (C) 2006 Freescale Semicondutor, Inc. All rights reserved. + * + * Author: Li Yang <leoli@freescale.com> + * Based on code from Shlomi Gridish <gridish@freescale.com> + * + * QUICC ENGINE Interrupt Controller + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/errno.h> +#include <linux/reboot.h> +#include <linux/slab.h> +#include <linux/stddef.h> +#include <linux/sched.h> +#include <linux/signal.h> +#include <linux/sysdev.h> +#include <linux/device.h> +#include <linux/bootmem.h> +#include <linux/spinlock.h> +#include <asm/irq.h> +#include <asm/io.h> +#include <asm/prom.h> +#include <asm/qe_ic.h> + +#include "qe_ic.h" + +static DEFINE_SPINLOCK(qe_ic_lock); + +static struct qe_ic_info qe_ic_info[] = { + [1] = { + .mask = 0x00008000, + .mask_reg = QEIC_CIMR, + .pri_code = 0, + .pri_reg = QEIC_CIPWCC, + }, + [2] = { + .mask = 0x00004000, + .mask_reg = QEIC_CIMR, + .pri_code = 1, + .pri_reg = QEIC_CIPWCC, + }, + [3] = { + .mask = 0x00002000, + .mask_reg = QEIC_CIMR, + .pri_code = 2, + .pri_reg = QEIC_CIPWCC, + }, + [10] = { + .mask = 0x00000040, + .mask_reg = QEIC_CIMR, + .pri_code = 1, + .pri_reg = QEIC_CIPZCC, + }, + [11] = { + .mask = 0x00000020, + .mask_reg = QEIC_CIMR, + .pri_code = 2, + .pri_reg = QEIC_CIPZCC, + }, + [12] = { + .mask = 0x00000010, + .mask_reg = QEIC_CIMR, + .pri_code = 3, + .pri_reg = QEIC_CIPZCC, + }, + [13] = { + .mask = 0x00000008, + .mask_reg = QEIC_CIMR, + .pri_code = 4, + .pri_reg = QEIC_CIPZCC, + }, + [14] = { + .mask = 0x00000004, + .mask_reg = QEIC_CIMR, + .pri_code = 5, + .pri_reg = QEIC_CIPZCC, + }, + [15] = { + .mask = 0x00000002, + .mask_reg = QEIC_CIMR, + .pri_code = 6, + .pri_reg = QEIC_CIPZCC, + }, + [20] = { + .mask = 0x10000000, + .mask_reg = QEIC_CRIMR, + .pri_code = 3, + .pri_reg = QEIC_CIPRTA, + }, + [25] = { + .mask = 0x00800000, + .mask_reg = QEIC_CRIMR, + .pri_code = 0, + .pri_reg = QEIC_CIPRTB, + }, + [26] = { + .mask = 0x00400000, + .mask_reg = QEIC_CRIMR, + .pri_code = 1, + .pri_reg = QEIC_CIPRTB, + }, + [27] = { + .mask = 0x00200000, + .mask_reg = QEIC_CRIMR, + .pri_code = 2, + .pri_reg = QEIC_CIPRTB, + }, + [28] = { + .mask = 0x00100000, + .mask_reg = QEIC_CRIMR, + .pri_code = 3, + .pri_reg = QEIC_CIPRTB, + }, + [32] = { + .mask = 0x80000000, + .mask_reg = QEIC_CIMR, + .pri_code = 0, + .pri_reg = QEIC_CIPXCC, + }, + [33] = { + .mask = 0x40000000, + .mask_reg = QEIC_CIMR, + .pri_code = 1, + .pri_reg = QEIC_CIPXCC, + }, + [34] = { + .mask = 0x20000000, + .mask_reg = QEIC_CIMR, + .pri_code = 2, + .pri_reg = QEIC_CIPXCC, + }, + [35] = { + .mask = 0x10000000, + .mask_reg = QEIC_CIMR, + .pri_code = 3, + .pri_reg = QEIC_CIPXCC, + }, + [36] = { + .mask = 0x08000000, + .mask_reg = QEIC_CIMR, + .pri_code = 4, + .pri_reg = QEIC_CIPXCC, + }, + [40] = { + .mask = 0x00800000, + .mask_reg = QEIC_CIMR, + .pri_code = 0, + .pri_reg = QEIC_CIPYCC, + }, + [41] = { + .mask = 0x00400000, + .mask_reg = QEIC_CIMR, + .pri_code = 1, + .pri_reg = QEIC_CIPYCC, + }, + [42] = { + .mask = 0x00200000, + .mask_reg = QEIC_CIMR, + .pri_code = 2, + .pri_reg = QEIC_CIPYCC, + }, + [43] = { + .mask = 0x00100000, + .mask_reg = QEIC_CIMR, + .pri_code = 3, + .pri_reg = QEIC_CIPYCC, + }, +}; + +static inline u32 qe_ic_read(volatile __be32 __iomem * base, unsigned int reg) +{ + return in_be32(base + (reg >> 2)); +} + +static inline void qe_ic_write(volatile __be32 __iomem * base, unsigned int reg, + u32 value) +{ + out_be32(base + (reg >> 2), value); +} + +static inline struct qe_ic *qe_ic_from_irq(unsigned int virq) +{ + return irq_desc[virq].chip_data; +} + +#define virq_to_hw(virq) ((unsigned int)irq_map[virq].hwirq) + +static void qe_ic_unmask_irq(unsigned int virq) +{ + struct qe_ic *qe_ic = qe_ic_from_irq(virq); + unsigned int src = virq_to_hw(virq); + unsigned long flags; + u32 temp; + + spin_lock_irqsave(&qe_ic_lock, flags); + + temp = qe_ic_read(qe_ic->regs, qe_ic_info[src].mask_reg); + qe_ic_write(qe_ic->regs, qe_ic_info[src].mask_reg, + temp | qe_ic_info[src].mask); + + spin_unlock_irqrestore(&qe_ic_lock, flags); +} + +static void qe_ic_mask_irq(unsigned int virq) +{ + struct qe_ic *qe_ic = qe_ic_from_irq(virq); + unsigned int src = virq_to_hw(virq); + unsigned long flags; + u32 temp; + + spin_lock_irqsave(&qe_ic_lock, flags); + + temp = qe_ic_read(qe_ic->regs, qe_ic_info[src].mask_reg); + qe_ic_write(qe_ic->regs, qe_ic_info[src].mask_reg, + temp & ~qe_ic_info[src].mask); + + spin_unlock_irqrestore(&qe_ic_lock, flags); +} + +static void qe_ic_mask_irq_and_ack(unsigned int virq) +{ + struct qe_ic *qe_ic = qe_ic_from_irq(virq); + unsigned int src = virq_to_hw(virq); + unsigned long flags; + u32 temp; + + spin_lock_irqsave(&qe_ic_lock, flags); + + temp = qe_ic_read(qe_ic->regs, qe_ic_info[src].mask_reg); + qe_ic_write(qe_ic->regs, qe_ic_info[src].mask_reg, + temp & ~qe_ic_info[src].mask); + + /* There is nothing to do for ack here, ack is handled in ISR */ + + spin_unlock_irqrestore(&qe_ic_lock, flags); +} + +static struct irq_chip qe_ic_irq_chip = { + .typename = " QEIC ", + .unmask = qe_ic_unmask_irq, + .mask = qe_ic_mask_irq, + .mask_ack = qe_ic_mask_irq_and_ack, +}; + +static int qe_ic_host_match(struct irq_host *h, struct device_node *node) +{ + struct qe_ic *qe_ic = h->host_data; + + /* Exact match, unless qe_ic node is NULL */ + return qe_ic->of_node == NULL || qe_ic->of_node == node; +} + +static int qe_ic_host_map(struct irq_host *h, unsigned int virq, + irq_hw_number_t hw) +{ + struct qe_ic *qe_ic = h->host_data; + struct irq_chip *chip; + + if (qe_ic_info[hw].mask == 0) { + printk(KERN_ERR "Can't map reserved IRQ \n"); + return -EINVAL; + } + /* Default chip */ + chip = &qe_ic->hc_irq; + + set_irq_chip_data(virq, qe_ic); + get_irq_desc(virq)->status |= IRQ_LEVEL; + + set_irq_chip_and_handler(virq, chip, handle_level_irq); + + return 0; +} + +static int qe_ic_host_xlate(struct irq_host *h, struct device_node *ct, + u32 * intspec, unsigned int intsize, + irq_hw_number_t * out_hwirq, + unsigned int *out_flags) +{ + *out_hwirq = intspec[0]; + if (intsize > 1) + *out_flags = intspec[1]; + else + *out_flags = IRQ_TYPE_NONE; + return 0; +} + +static struct irq_host_ops qe_ic_host_ops = { + .match = qe_ic_host_match, + .map = qe_ic_host_map, + .xlate = qe_ic_host_xlate, +}; + +/* Return an interrupt vector or NO_IRQ if no interrupt is pending. */ +unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic, struct pt_regs *regs) +{ + int irq; + + BUG_ON(qe_ic == NULL); + + /* get the interrupt source vector. */ + irq = qe_ic_read(qe_ic->regs, QEIC_CIVEC) >> 26; + + if (irq == 0) + return NO_IRQ; + + return irq_linear_revmap(qe_ic->irqhost, irq); +} + +/* Return an interrupt vector or NO_IRQ if no interrupt is pending. */ +unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic, struct pt_regs *regs) +{ + int irq; + + BUG_ON(qe_ic == NULL); + + /* get the interrupt source vector. */ + irq = qe_ic_read(qe_ic->regs, QEIC_CHIVEC) >> 26; + + if (irq == 0) + return NO_IRQ; + + return irq_linear_revmap(qe_ic->irqhost, irq); +} + +/* FIXME: We mask all the QE Low interrupts while handling. We should + * let other interrupt come in, but BAD interrupts are generated */ +void fastcall qe_ic_cascade_low(unsigned int irq, struct irq_desc *desc, + struct pt_regs *regs) +{ + struct qe_ic *qe_ic = desc->handler_data; + struct irq_chip *chip = irq_desc[irq].chip; + + unsigned int cascade_irq = qe_ic_get_low_irq(qe_ic, regs); + + chip->mask_ack(irq); + if (cascade_irq != NO_IRQ) + generic_handle_irq(cascade_irq, regs); + chip->unmask(irq); +} + +/* FIXME: We mask all the QE High interrupts while handling. We should + * let other interrupt come in, but BAD interrupts are generated */ +void fastcall qe_ic_cascade_high(unsigned int irq, struct irq_desc *desc, + struct pt_regs *regs) +{ + struct qe_ic *qe_ic = desc->handler_data; + struct irq_chip *chip = irq_desc[irq].chip; + + unsigned int cascade_irq = qe_ic_get_high_irq(qe_ic, regs); + + chip->mask_ack(irq); + if (cascade_irq != NO_IRQ) + generic_handle_irq(cascade_irq, regs); + chip->unmask(irq); +} + +void __init qe_ic_init(struct device_node *node, unsigned int flags) +{ + struct qe_ic *qe_ic; + struct resource res; + u32 temp = 0, ret, high_active = 0; + + qe_ic = alloc_bootmem(sizeof(struct qe_ic)); + if (qe_ic == NULL) + return; + + memset(qe_ic, 0, sizeof(struct qe_ic)); + qe_ic->of_node = node ? of_node_get(node) : NULL; + + qe_ic->irqhost = irq_alloc_host(IRQ_HOST_MAP_LINEAR, + NR_QE_IC_INTS, &qe_ic_host_ops, 0); + if (qe_ic->irqhost == NULL) { + of_node_put(node); + return; + } + + ret = of_address_to_resource(node, 0, &res); + if (ret) + return; + + qe_ic->regs = ioremap(res.start, res.end - res.start + 1); + + qe_ic->irqhost->host_data = qe_ic; + qe_ic->hc_irq = qe_ic_irq_chip; + + qe_ic->virq_high = irq_of_parse_and_map(node, 0); + qe_ic->virq_low = irq_of_parse_and_map(node, 1); + + if (qe_ic->virq_low == NO_IRQ) { + printk(KERN_ERR "Failed to map QE_IC low IRQ\n"); + return; + } + + /* default priority scheme is grouped. If spread mode is */ + /* required, configure cicr accordingly. */ + if (flags & QE_IC_SPREADMODE_GRP_W) + temp |= CICR_GWCC; + if (flags & QE_IC_SPREADMODE_GRP_X) + temp |= CICR_GXCC; + if (flags & QE_IC_SPREADMODE_GRP_Y) + temp |= CICR_GYCC; + if (flags & QE_IC_SPREADMODE_GRP_Z) + temp |= CICR_GZCC; + if (flags & QE_IC_SPREADMODE_GRP_RISCA) + temp |= CICR_GRTA; + if (flags & QE_IC_SPREADMODE_GRP_RISCB) + temp |= CICR_GRTB; + + /* choose destination signal for highest priority interrupt */ + if (flags & QE_IC_HIGH_SIGNAL) { + temp |= (SIGNAL_HIGH << CICR_HPIT_SHIFT); + high_active = 1; + } + + qe_ic_write(qe_ic->regs, QEIC_CICR, temp); + + set_irq_data(qe_ic->virq_low, qe_ic); + set_irq_chained_handler(qe_ic->virq_low, qe_ic_cascade_low); + + if (qe_ic->virq_high != NO_IRQ) { + set_irq_data(qe_ic->virq_high, qe_ic); + set_irq_chained_handler(qe_ic->virq_high, qe_ic_cascade_high); + } + + printk("QEIC (%d IRQ sources) at %p\n", NR_QE_IC_INTS, qe_ic->regs); +} + +void qe_ic_set_highest_priority(unsigned int virq, int high) +{ + struct qe_ic *qe_ic = qe_ic_from_irq(virq); + unsigned int src = virq_to_hw(virq); + u32 temp = 0; + + temp = qe_ic_read(qe_ic->regs, QEIC_CICR); + + temp &= ~CICR_HP_MASK; + temp |= src << CICR_HP_SHIFT; + + temp &= ~CICR_HPIT_MASK; + temp |= (high ? SIGNAL_HIGH : SIGNAL_LOW) << CICR_HPIT_SHIFT; + + qe_ic_write(qe_ic->regs, QEIC_CICR, temp); +} + +/* Set Priority level within its group, from 1 to 8 */ +int qe_ic_set_priority(unsigned int virq, unsigned int priority) +{ + struct qe_ic *qe_ic = qe_ic_from_irq(virq); + unsigned int src = virq_to_hw(virq); + u32 temp; + + if (priority > 8 || priority == 0) + return -EINVAL; + if (src > 127) + return -EINVAL; + if (qe_ic_info[src].pri_reg == 0) + return -EINVAL; + + temp = qe_ic_read(qe_ic->regs, qe_ic_info[src].pri_reg); + + if (priority < 4) { + temp &= ~(0x7 << (32 - priority * 3)); + temp |= qe_ic_info[src].pri_code << (32 - priority * 3); + } else { + temp &= ~(0x7 << (24 - priority * 3)); + temp |= qe_ic_info[src].pri_code << (24 - priority * 3); + } + + qe_ic_write(qe_ic->regs, qe_ic_info[src].pri_reg, temp); + + return 0; +} + +/* Set a QE priority to use high irq, only priority 1~2 can use high irq */ +int qe_ic_set_high_priority(unsigned int virq, unsigned int priority, int high) +{ + struct qe_ic *qe_ic = qe_ic_from_irq(virq); + unsigned int src = virq_to_hw(virq); + u32 temp, control_reg = QEIC_CICNR, shift = 0; + + if (priority > 2 || priority == 0) + return -EINVAL; + + switch (qe_ic_info[src].pri_reg) { + case QEIC_CIPZCC: + shift = CICNR_ZCC1T_SHIFT; + break; + case QEIC_CIPWCC: + shift = CICNR_WCC1T_SHIFT; + break; + case QEIC_CIPYCC: + shift = CICNR_YCC1T_SHIFT; + break; + case QEIC_CIPXCC: + shift = CICNR_XCC1T_SHIFT; + break; + case QEIC_CIPRTA: + shift = CRICR_RTA1T_SHIFT; + control_reg = QEIC_CRICR; + break; + case QEIC_CIPRTB: + shift = CRICR_RTB1T_SHIFT; + control_reg = QEIC_CRICR; + break; + default: + return -EINVAL; + } + + shift += (2 - priority) * 2; + temp = qe_ic_read(qe_ic->regs, control_reg); + temp &= ~(SIGNAL_MASK << shift); + temp |= (high ? SIGNAL_HIGH : SIGNAL_LOW) << shift; + qe_ic_write(qe_ic->regs, control_reg, temp); + + return 0; +} + +static struct sysdev_class qe_ic_sysclass = { + set_kset_name("qe_ic"), +}; + +static struct sys_device device_qe_ic = { + .id = 0, + .cls = &qe_ic_sysclass, +}; + +static int __init init_qe_ic_sysfs(void) +{ + int rc; + + printk(KERN_DEBUG "Registering qe_ic with sysfs...\n"); + + rc = sysdev_class_register(&qe_ic_sysclass); + if (rc) { + printk(KERN_ERR "Failed registering qe_ic sys class\n"); + return -ENODEV; + } + rc = sysdev_register(&device_qe_ic); + if (rc) { + printk(KERN_ERR "Failed registering qe_ic sys device\n"); + return -ENODEV; + } + return 0; +} + +subsys_initcall(init_qe_ic_sysfs); diff --git a/arch/powerpc/sysdev/qe_lib/qe_ic.h b/arch/powerpc/sysdev/qe_lib/qe_ic.h new file mode 100644 index 000000000000..9a631adb189d --- /dev/null +++ b/arch/powerpc/sysdev/qe_lib/qe_ic.h @@ -0,0 +1,106 @@ +/* + * arch/powerpc/sysdev/qe_lib/qe_ic.h + * + * QUICC ENGINE Interrupt Controller Header + * + * Copyright (C) 2006 Freescale Semicondutor, Inc. All rights reserved. + * + * Author: Li Yang <leoli@freescale.com> + * Based on code from Shlomi Gridish <gridish@freescale.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#ifndef _POWERPC_SYSDEV_QE_IC_H +#define _POWERPC_SYSDEV_QE_IC_H + +#include <asm/qe_ic.h> + +#define NR_QE_IC_INTS 64 + +/* QE IC registers offset */ +#define QEIC_CICR 0x00 +#define QEIC_CIVEC 0x04 +#define QEIC_CRIPNR 0x08 +#define QEIC_CIPNR 0x0c +#define QEIC_CIPXCC 0x10 +#define QEIC_CIPYCC 0x14 +#define QEIC_CIPWCC 0x18 +#define QEIC_CIPZCC 0x1c +#define QEIC_CIMR 0x20 +#define QEIC_CRIMR 0x24 +#define QEIC_CICNR 0x28 +#define QEIC_CIPRTA 0x30 +#define QEIC_CIPRTB 0x34 +#define QEIC_CRICR 0x3c +#define QEIC_CHIVEC 0x60 + +/* Interrupt priority registers */ +#define CIPCC_SHIFT_PRI0 29 +#define CIPCC_SHIFT_PRI1 26 +#define CIPCC_SHIFT_PRI2 23 +#define CIPCC_SHIFT_PRI3 20 +#define CIPCC_SHIFT_PRI4 13 +#define CIPCC_SHIFT_PRI5 10 +#define CIPCC_SHIFT_PRI6 7 +#define CIPCC_SHIFT_PRI7 4 + +/* CICR priority modes */ +#define CICR_GWCC 0x00040000 +#define CICR_GXCC 0x00020000 +#define CICR_GYCC 0x00010000 +#define CICR_GZCC 0x00080000 +#define CICR_GRTA 0x00200000 +#define CICR_GRTB 0x00400000 +#define CICR_HPIT_SHIFT 8 +#define CICR_HPIT_MASK 0x00000300 +#define CICR_HP_SHIFT 24 +#define CICR_HP_MASK 0x3f000000 + +/* CICNR */ +#define CICNR_WCC1T_SHIFT 20 +#define CICNR_ZCC1T_SHIFT 28 +#define CICNR_YCC1T_SHIFT 12 +#define CICNR_XCC1T_SHIFT 4 + +/* CRICR */ +#define CRICR_RTA1T_SHIFT 20 +#define CRICR_RTB1T_SHIFT 28 + +/* Signal indicator */ +#define SIGNAL_MASK 3 +#define SIGNAL_HIGH 2 +#define SIGNAL_LOW 0 + +struct qe_ic { + /* Control registers offset */ + volatile u32 __iomem *regs; + + /* The remapper for this QEIC */ + struct irq_host *irqhost; + + /* The "linux" controller struct */ + struct irq_chip hc_irq; + + /* The device node of the interrupt controller */ + struct device_node *of_node; + + /* VIRQ numbers of QE high/low irqs */ + unsigned int virq_high; + unsigned int virq_low; +}; + +/* + * QE interrupt controller internal structure + */ +struct qe_ic_info { + u32 mask; /* location of this source at the QIMR register. */ + u32 mask_reg; /* Mask register offset */ + u8 pri_code; /* for grouped interrupts sources - the interrupt + code as appears at the group priority register */ + u32 pri_reg; /* Group priority register offset */ +}; + +#endif /* _POWERPC_SYSDEV_QE_IC_H */ diff --git a/arch/powerpc/sysdev/qe_lib/qe_io.c b/arch/powerpc/sysdev/qe_lib/qe_io.c new file mode 100644 index 000000000000..aea435970389 --- /dev/null +++ b/arch/powerpc/sysdev/qe_lib/qe_io.c @@ -0,0 +1,226 @@ +/* + * arch/powerpc/sysdev/qe_lib/qe_io.c + * + * QE Parallel I/O ports configuration routines + * + * Copyright (C) Freescale Semicondutor, Inc. 2006. All rights reserved. + * + * Author: Li Yang <LeoLi@freescale.com> + * Based on code from Shlomi Gridish <gridish@freescale.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/config.h> +#include <linux/stddef.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/errno.h> +#include <linux/module.h> +#include <linux/ioport.h> + +#include <asm/io.h> +#include <asm/prom.h> +#include <sysdev/fsl_soc.h> + +#undef DEBUG + +#define NUM_OF_PINS 32 + +struct port_regs { + __be32 cpodr; /* Open drain register */ + __be32 cpdata; /* Data register */ + __be32 cpdir1; /* Direction register */ + __be32 cpdir2; /* Direction register */ + __be32 cppar1; /* Pin assignment register */ + __be32 cppar2; /* Pin assignment register */ +}; + +static struct port_regs *par_io = NULL; +static int num_par_io_ports = 0; + +int par_io_init(struct device_node *np) +{ + struct resource res; + int ret; + const u32 *num_ports; + + /* Map Parallel I/O ports registers */ + ret = of_address_to_resource(np, 0, &res); + if (ret) + return ret; + par_io = ioremap(res.start, res.end - res.start + 1); + + num_ports = get_property(np, "num-ports", NULL); + if (num_ports) + num_par_io_ports = *num_ports; + + return 0; +} + +int par_io_config_pin(u8 port, u8 pin, int dir, int open_drain, + int assignment, int has_irq) +{ + u32 pin_mask1bit, pin_mask2bits, new_mask2bits, tmp_val; + + if (!par_io) + return -1; + + /* calculate pin location for single and 2 bits information */ + pin_mask1bit = (u32) (1 << (NUM_OF_PINS - (pin + 1))); + + /* Set open drain, if required */ + tmp_val = in_be32(&par_io[port].cpodr); + if (open_drain) + out_be32(&par_io[port].cpodr, pin_mask1bit | tmp_val); + else + out_be32(&par_io[port].cpodr, ~pin_mask1bit & tmp_val); + + /* define direction */ + tmp_val = (pin > (NUM_OF_PINS / 2) - 1) ? + in_be32(&par_io[port].cpdir2) : + in_be32(&par_io[port].cpdir1); + + /* get all bits mask for 2 bit per port */ + pin_mask2bits = (u32) (0x3 << (NUM_OF_PINS - + (pin % (NUM_OF_PINS / 2) + 1) * 2)); + + /* Get the final mask we need for the right definition */ + new_mask2bits = (u32) (dir << (NUM_OF_PINS - + (pin % (NUM_OF_PINS / 2) + 1) * 2)); + + /* clear and set 2 bits mask */ + if (pin > (NUM_OF_PINS / 2) - 1) { + out_be32(&par_io[port].cpdir2, + ~pin_mask2bits & tmp_val); + tmp_val &= ~pin_mask2bits; + out_be32(&par_io[port].cpdir2, new_mask2bits | tmp_val); + } else { + out_be32(&par_io[port].cpdir1, + ~pin_mask2bits & tmp_val); + tmp_val &= ~pin_mask2bits; + out_be32(&par_io[port].cpdir1, new_mask2bits | tmp_val); + } + /* define pin assignment */ + tmp_val = (pin > (NUM_OF_PINS / 2) - 1) ? + in_be32(&par_io[port].cppar2) : + in_be32(&par_io[port].cppar1); + + new_mask2bits = (u32) (assignment << (NUM_OF_PINS - + (pin % (NUM_OF_PINS / 2) + 1) * 2)); + /* clear and set 2 bits mask */ + if (pin > (NUM_OF_PINS / 2) - 1) { + out_be32(&par_io[port].cppar2, + ~pin_mask2bits & tmp_val); + tmp_val &= ~pin_mask2bits; + out_be32(&par_io[port].cppar2, new_mask2bits | tmp_val); + } else { + out_be32(&par_io[port].cppar1, + ~pin_mask2bits & tmp_val); + tmp_val &= ~pin_mask2bits; + out_be32(&par_io[port].cppar1, new_mask2bits | tmp_val); + } + + return 0; +} +EXPORT_SYMBOL(par_io_config_pin); + +int par_io_data_set(u8 port, u8 pin, u8 val) +{ + u32 pin_mask, tmp_val; + + if (port >= num_par_io_ports) + return -EINVAL; + if (pin >= NUM_OF_PINS) + return -EINVAL; + /* calculate pin location */ + pin_mask = (u32) (1 << (NUM_OF_PINS - 1 - pin)); + + tmp_val = in_be32(&par_io[port].cpdata); + + if (val == 0) /* clear */ + out_be32(&par_io[port].cpdata, ~pin_mask & tmp_val); + else /* set */ + out_be32(&par_io[port].cpdata, pin_mask | tmp_val); + + return 0; +} +EXPORT_SYMBOL(par_io_data_set); + +int par_io_of_config(struct device_node *np) +{ + struct device_node *pio; + const phandle *ph; + int pio_map_len; + const unsigned int *pio_map; + + if (par_io == NULL) { + printk(KERN_ERR "par_io not initialized \n"); + return -1; + } + + ph = get_property(np, "pio-handle", NULL); + if (ph == 0) { + printk(KERN_ERR "pio-handle not available \n"); + return -1; + } + + pio = of_find_node_by_phandle(*ph); + + pio_map = get_property(pio, "pio-map", &pio_map_len); + if (pio_map == NULL) { + printk(KERN_ERR "pio-map is not set! \n"); + return -1; + } + pio_map_len /= sizeof(unsigned int); + if ((pio_map_len % 6) != 0) { + printk(KERN_ERR "pio-map format wrong! \n"); + return -1; + } + + while (pio_map_len > 0) { + par_io_config_pin((u8) pio_map[0], (u8) pio_map[1], + (int) pio_map[2], (int) pio_map[3], + (int) pio_map[4], (int) pio_map[5]); + pio_map += 6; + pio_map_len -= 6; + } + of_node_put(pio); + return 0; +} +EXPORT_SYMBOL(par_io_of_config); + +#ifdef DEBUG +static void dump_par_io(void) +{ + int i; + + printk(KERN_INFO "PAR IO registars:\n"); + printk(KERN_INFO "Base address: 0x%08x\n", (u32) par_io); + for (i = 0; i < num_par_io_ports; i++) { + printk(KERN_INFO "cpodr[%d] : addr - 0x%08x, val - 0x%08x\n", + i, (u32) & par_io[i].cpodr, + in_be32(&par_io[i].cpodr)); + printk(KERN_INFO "cpdata[%d]: addr - 0x%08x, val - 0x%08x\n", + i, (u32) & par_io[i].cpdata, + in_be32(&par_io[i].cpdata)); + printk(KERN_INFO "cpdir1[%d]: addr - 0x%08x, val - 0x%08x\n", + i, (u32) & par_io[i].cpdir1, + in_be32(&par_io[i].cpdir1)); + printk(KERN_INFO "cpdir2[%d]: addr - 0x%08x, val - 0x%08x\n", + i, (u32) & par_io[i].cpdir2, + in_be32(&par_io[i].cpdir2)); + printk(KERN_INFO "cppar1[%d]: addr - 0x%08x, val - 0x%08x\n", + i, (u32) & par_io[i].cppar1, + in_be32(&par_io[i].cppar1)); + printk(KERN_INFO "cppar2[%d]: addr - 0x%08x, val - 0x%08x\n", + i, (u32) & par_io[i].cppar2, + in_be32(&par_io[i].cppar2)); + } + +} +EXPORT_SYMBOL(dump_par_io); +#endif /* DEBUG */ diff --git a/arch/powerpc/sysdev/qe_lib/ucc.c b/arch/powerpc/sysdev/qe_lib/ucc.c new file mode 100644 index 000000000000..916c9e5df57f --- /dev/null +++ b/arch/powerpc/sysdev/qe_lib/ucc.c @@ -0,0 +1,251 @@ +/* + * arch/powerpc/sysdev/qe_lib/ucc.c + * + * QE UCC API Set - UCC specific routines implementations. + * + * Copyright (C) 2006 Freescale Semicondutor, Inc. All rights reserved. + * + * Authors: Shlomi Gridish <gridish@freescale.com> + * Li Yang <leoli@freescale.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/errno.h> +#include <linux/slab.h> +#include <linux/stddef.h> + +#include <asm/irq.h> +#include <asm/io.h> +#include <asm/immap_qe.h> +#include <asm/qe.h> +#include <asm/ucc.h> + +static DEFINE_SPINLOCK(ucc_lock); + +int ucc_set_qe_mux_mii_mng(int ucc_num) +{ + unsigned long flags; + + spin_lock_irqsave(&ucc_lock, flags); + out_be32(&qe_immr->qmx.cmxgcr, + ((in_be32(&qe_immr->qmx.cmxgcr) & + ~QE_CMXGCR_MII_ENET_MNG) | + (ucc_num << QE_CMXGCR_MII_ENET_MNG_SHIFT))); + spin_unlock_irqrestore(&ucc_lock, flags); + + return 0; +} + +int ucc_set_type(int ucc_num, struct ucc_common *regs, + enum ucc_speed_type speed) +{ + u8 guemr = 0; + + /* check if the UCC number is in range. */ + if ((ucc_num > UCC_MAX_NUM - 1) || (ucc_num < 0)) + return -EINVAL; + + guemr = regs->guemr; + guemr &= ~(UCC_GUEMR_MODE_MASK_RX | UCC_GUEMR_MODE_MASK_TX); + switch (speed) { + case UCC_SPEED_TYPE_SLOW: + guemr |= (UCC_GUEMR_MODE_SLOW_RX | UCC_GUEMR_MODE_SLOW_TX); + break; + case UCC_SPEED_TYPE_FAST: + guemr |= (UCC_GUEMR_MODE_FAST_RX | UCC_GUEMR_MODE_FAST_TX); + break; + default: + return -EINVAL; + } + regs->guemr = guemr; + + return 0; +} + +int ucc_init_guemr(struct ucc_common *regs) +{ + u8 guemr = 0; + + if (!regs) + return -EINVAL; + + /* Set bit 3 (which is reserved in the GUEMR register) to 1 */ + guemr = UCC_GUEMR_SET_RESERVED3; + + regs->guemr = guemr; + + return 0; +} + +static void get_cmxucr_reg(int ucc_num, volatile u32 ** p_cmxucr, u8 * reg_num, + u8 * shift) +{ + switch (ucc_num) { + case 0: *p_cmxucr = &(qe_immr->qmx.cmxucr1); + *reg_num = 1; + *shift = 16; + break; + case 2: *p_cmxucr = &(qe_immr->qmx.cmxucr1); + *reg_num = 1; + *shift = 0; + break; + case 4: *p_cmxucr = &(qe_immr->qmx.cmxucr2); + *reg_num = 2; + *shift = 16; + break; + case 6: *p_cmxucr = &(qe_immr->qmx.cmxucr2); + *reg_num = 2; + *shift = 0; + break; + case 1: *p_cmxucr = &(qe_immr->qmx.cmxucr3); + *reg_num = 3; + *shift = 16; + break; + case 3: *p_cmxucr = &(qe_immr->qmx.cmxucr3); + *reg_num = 3; + *shift = 0; + break; + case 5: *p_cmxucr = &(qe_immr->qmx.cmxucr4); + *reg_num = 4; + *shift = 16; + break; + case 7: *p_cmxucr = &(qe_immr->qmx.cmxucr4); + *reg_num = 4; + *shift = 0; + break; + default: + break; + } +} + +int ucc_mux_set_grant_tsa_bkpt(int ucc_num, int set, u32 mask) +{ + volatile u32 *p_cmxucr; + u8 reg_num; + u8 shift; + + /* check if the UCC number is in range. */ + if ((ucc_num > UCC_MAX_NUM - 1) || (ucc_num < 0)) + return -EINVAL; + + get_cmxucr_reg(ucc_num, &p_cmxucr, ®_num, &shift); + + if (set) + out_be32(p_cmxucr, in_be32(p_cmxucr) | (mask << shift)); + else + out_be32(p_cmxucr, in_be32(p_cmxucr) & ~(mask << shift)); + + return 0; +} + +int ucc_set_qe_mux_rxtx(int ucc_num, enum qe_clock clock, enum comm_dir mode) +{ + volatile u32 *p_cmxucr; + u8 reg_num; + u8 shift; + u32 clock_bits; + u32 clock_mask; + int source = -1; + + /* check if the UCC number is in range. */ + if ((ucc_num > UCC_MAX_NUM - 1) || (ucc_num < 0)) + return -EINVAL; + + if (!((mode == COMM_DIR_RX) || (mode == COMM_DIR_TX))) { + printk(KERN_ERR + "ucc_set_qe_mux_rxtx: bad comm mode type passed."); + return -EINVAL; + } + + get_cmxucr_reg(ucc_num, &p_cmxucr, ®_num, &shift); + + switch (reg_num) { + case 1: + switch (clock) { + case QE_BRG1: source = 1; break; + case QE_BRG2: source = 2; break; + case QE_BRG7: source = 3; break; + case QE_BRG8: source = 4; break; + case QE_CLK9: source = 5; break; + case QE_CLK10: source = 6; break; + case QE_CLK11: source = 7; break; + case QE_CLK12: source = 8; break; + case QE_CLK15: source = 9; break; + case QE_CLK16: source = 10; break; + default: source = -1; break; + } + break; + case 2: + switch (clock) { + case QE_BRG5: source = 1; break; + case QE_BRG6: source = 2; break; + case QE_BRG7: source = 3; break; + case QE_BRG8: source = 4; break; + case QE_CLK13: source = 5; break; + case QE_CLK14: source = 6; break; + case QE_CLK19: source = 7; break; + case QE_CLK20: source = 8; break; + case QE_CLK15: source = 9; break; + case QE_CLK16: source = 10; break; + default: source = -1; break; + } + break; + case 3: + switch (clock) { + case QE_BRG9: source = 1; break; + case QE_BRG10: source = 2; break; + case QE_BRG15: source = 3; break; + case QE_BRG16: source = 4; break; + case QE_CLK3: source = 5; break; + case QE_CLK4: source = 6; break; + case QE_CLK17: source = 7; break; + case QE_CLK18: source = 8; break; + case QE_CLK7: source = 9; break; + case QE_CLK8: source = 10; break; + default: source = -1; break; + } + break; + case 4: + switch (clock) { + case QE_BRG13: source = 1; break; + case QE_BRG14: source = 2; break; + case QE_BRG15: source = 3; break; + case QE_BRG16: source = 4; break; + case QE_CLK5: source = 5; break; + case QE_CLK6: source = 6; break; + case QE_CLK21: source = 7; break; + case QE_CLK22: source = 8; break; + case QE_CLK7: source = 9; break; + case QE_CLK8: source = 10; break; + default: source = -1; break; + } + break; + default: + source = -1; + break; + } + + if (source == -1) { + printk(KERN_ERR + "ucc_set_qe_mux_rxtx: Bad combination of clock and UCC."); + return -ENOENT; + } + + clock_bits = (u32) source; + clock_mask = QE_CMXUCR_TX_CLK_SRC_MASK; + if (mode == COMM_DIR_RX) { + clock_bits <<= 4; /* Rx field is 4 bits to left of Tx field */ + clock_mask <<= 4; /* Rx field is 4 bits to left of Tx field */ + } + clock_bits <<= shift; + clock_mask <<= shift; + + out_be32(p_cmxucr, (in_be32(p_cmxucr) & ~clock_mask) | clock_bits); + + return 0; +} diff --git a/arch/powerpc/sysdev/qe_lib/ucc_fast.c b/arch/powerpc/sysdev/qe_lib/ucc_fast.c new file mode 100644 index 000000000000..c2be7348fcbd --- /dev/null +++ b/arch/powerpc/sysdev/qe_lib/ucc_fast.c @@ -0,0 +1,396 @@ +/* + * arch/powerpc/sysdev/qe_lib/ucc_fast.c + * + * QE UCC Fast API Set - UCC Fast specific routines implementations. + * + * Copyright (C) 2006 Freescale Semicondutor, Inc. All rights reserved. + * + * Authors: Shlomi Gridish <gridish@freescale.com> + * Li Yang <leoli@freescale.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/errno.h> +#include <linux/slab.h> +#include <linux/stddef.h> +#include <linux/interrupt.h> + +#include <asm/io.h> +#include <asm/immap_qe.h> +#include <asm/qe.h> + +#include <asm/ucc.h> +#include <asm/ucc_fast.h> + +#define uccf_printk(level, format, arg...) \ + printk(level format "\n", ## arg) + +#define uccf_dbg(format, arg...) \ + uccf_printk(KERN_DEBUG , format , ## arg) +#define uccf_err(format, arg...) \ + uccf_printk(KERN_ERR , format , ## arg) +#define uccf_info(format, arg...) \ + uccf_printk(KERN_INFO , format , ## arg) +#define uccf_warn(format, arg...) \ + uccf_printk(KERN_WARNING , format , ## arg) + +#ifdef UCCF_VERBOSE_DEBUG +#define uccf_vdbg uccf_dbg +#else +#define uccf_vdbg(fmt, args...) do { } while (0) +#endif /* UCCF_VERBOSE_DEBUG */ + +void ucc_fast_dump_regs(struct ucc_fast_private * uccf) +{ + uccf_info("UCC%d Fast registers:", uccf->uf_info->ucc_num); + uccf_info("Base address: 0x%08x", (u32) uccf->uf_regs); + + uccf_info("gumr : addr - 0x%08x, val - 0x%08x", + (u32) & uccf->uf_regs->gumr, in_be32(&uccf->uf_regs->gumr)); + uccf_info("upsmr : addr - 0x%08x, val - 0x%08x", + (u32) & uccf->uf_regs->upsmr, in_be32(&uccf->uf_regs->upsmr)); + uccf_info("utodr : addr - 0x%08x, val - 0x%04x", + (u32) & uccf->uf_regs->utodr, in_be16(&uccf->uf_regs->utodr)); + uccf_info("udsr : addr - 0x%08x, val - 0x%04x", + (u32) & uccf->uf_regs->udsr, in_be16(&uccf->uf_regs->udsr)); + uccf_info("ucce : addr - 0x%08x, val - 0x%08x", + (u32) & uccf->uf_regs->ucce, in_be32(&uccf->uf_regs->ucce)); + uccf_info("uccm : addr - 0x%08x, val - 0x%08x", + (u32) & uccf->uf_regs->uccm, in_be32(&uccf->uf_regs->uccm)); + uccf_info("uccs : addr - 0x%08x, val - 0x%02x", + (u32) & uccf->uf_regs->uccs, uccf->uf_regs->uccs); + uccf_info("urfb : addr - 0x%08x, val - 0x%08x", + (u32) & uccf->uf_regs->urfb, in_be32(&uccf->uf_regs->urfb)); + uccf_info("urfs : addr - 0x%08x, val - 0x%04x", + (u32) & uccf->uf_regs->urfs, in_be16(&uccf->uf_regs->urfs)); + uccf_info("urfet : addr - 0x%08x, val - 0x%04x", + (u32) & uccf->uf_regs->urfet, in_be16(&uccf->uf_regs->urfet)); + uccf_info("urfset: addr - 0x%08x, val - 0x%04x", + (u32) & uccf->uf_regs->urfset, + in_be16(&uccf->uf_regs->urfset)); + uccf_info("utfb : addr - 0x%08x, val - 0x%08x", + (u32) & uccf->uf_regs->utfb, in_be32(&uccf->uf_regs->utfb)); + uccf_info("utfs : addr - 0x%08x, val - 0x%04x", + (u32) & uccf->uf_regs->utfs, in_be16(&uccf->uf_regs->utfs)); + uccf_info("utfet : addr - 0x%08x, val - 0x%04x", + (u32) & uccf->uf_regs->utfet, in_be16(&uccf->uf_regs->utfet)); + uccf_info("utftt : addr - 0x%08x, val - 0x%04x", + (u32) & uccf->uf_regs->utftt, in_be16(&uccf->uf_regs->utftt)); + uccf_info("utpt : addr - 0x%08x, val - 0x%04x", + (u32) & uccf->uf_regs->utpt, in_be16(&uccf->uf_regs->utpt)); + uccf_info("urtry : addr - 0x%08x, val - 0x%08x", + (u32) & uccf->uf_regs->urtry, in_be32(&uccf->uf_regs->urtry)); + uccf_info("guemr : addr - 0x%08x, val - 0x%02x", + (u32) & uccf->uf_regs->guemr, uccf->uf_regs->guemr); +} + +u32 ucc_fast_get_qe_cr_subblock(int uccf_num) +{ + switch (uccf_num) { + case 0: return QE_CR_SUBBLOCK_UCCFAST1; + case 1: return QE_CR_SUBBLOCK_UCCFAST2; + case 2: return QE_CR_SUBBLOCK_UCCFAST3; + case 3: return QE_CR_SUBBLOCK_UCCFAST4; + case 4: return QE_CR_SUBBLOCK_UCCFAST5; + case 5: return QE_CR_SUBBLOCK_UCCFAST6; + case 6: return QE_CR_SUBBLOCK_UCCFAST7; + case 7: return QE_CR_SUBBLOCK_UCCFAST8; + default: return QE_CR_SUBBLOCK_INVALID; + } +} + +void ucc_fast_transmit_on_demand(struct ucc_fast_private * uccf) +{ + out_be16(&uccf->uf_regs->utodr, UCC_FAST_TOD); +} + +void ucc_fast_enable(struct ucc_fast_private * uccf, enum comm_dir mode) +{ + struct ucc_fast *uf_regs; + u32 gumr; + + uf_regs = uccf->uf_regs; + + /* Enable reception and/or transmission on this UCC. */ + gumr = in_be32(&uf_regs->gumr); + if (mode & COMM_DIR_TX) { + gumr |= UCC_FAST_GUMR_ENT; + uccf->enabled_tx = 1; + } + if (mode & COMM_DIR_RX) { + gumr |= UCC_FAST_GUMR_ENR; + uccf->enabled_rx = 1; + } + out_be32(&uf_regs->gumr, gumr); +} + +void ucc_fast_disable(struct ucc_fast_private * uccf, enum comm_dir mode) +{ + struct ucc_fast *uf_regs; + u32 gumr; + + uf_regs = uccf->uf_regs; + + /* Disable reception and/or transmission on this UCC. */ + gumr = in_be32(&uf_regs->gumr); + if (mode & COMM_DIR_TX) { + gumr &= ~UCC_FAST_GUMR_ENT; + uccf->enabled_tx = 0; + } + if (mode & COMM_DIR_RX) { + gumr &= ~UCC_FAST_GUMR_ENR; + uccf->enabled_rx = 0; + } + out_be32(&uf_regs->gumr, gumr); +} + +int ucc_fast_init(struct ucc_fast_info * uf_info, struct ucc_fast_private ** uccf_ret) +{ + struct ucc_fast_private *uccf; + struct ucc_fast *uf_regs; + u32 gumr = 0; + int ret; + + uccf_vdbg("%s: IN", __FUNCTION__); + + if (!uf_info) + return -EINVAL; + + /* check if the UCC port number is in range. */ + if ((uf_info->ucc_num < 0) || (uf_info->ucc_num > UCC_MAX_NUM - 1)) { + uccf_err("ucc_fast_init: Illagal UCC number!"); + return -EINVAL; + } + + /* Check that 'max_rx_buf_length' is properly aligned (4). */ + if (uf_info->max_rx_buf_length & (UCC_FAST_MRBLR_ALIGNMENT - 1)) { + uccf_err("ucc_fast_init: max_rx_buf_length not aligned."); + return -EINVAL; + } + + /* Validate Virtual Fifo register values */ + if (uf_info->urfs < UCC_FAST_URFS_MIN_VAL) { + uccf_err + ("ucc_fast_init: Virtual Fifo register urfs too small."); + return -EINVAL; + } + + if (uf_info->urfs & (UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT - 1)) { + uccf_err + ("ucc_fast_init: Virtual Fifo register urfs not aligned."); + return -EINVAL; + } + + if (uf_info->urfet & (UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT - 1)) { + uccf_err + ("ucc_fast_init: Virtual Fifo register urfet not aligned."); + return -EINVAL; + } + + if (uf_info->urfset & (UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT - 1)) { + uccf_err + ("ucc_fast_init: Virtual Fifo register urfset not aligned."); + return -EINVAL; + } + + if (uf_info->utfs & (UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT - 1)) { + uccf_err + ("ucc_fast_init: Virtual Fifo register utfs not aligned."); + return -EINVAL; + } + + if (uf_info->utfet & (UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT - 1)) { + uccf_err + ("ucc_fast_init: Virtual Fifo register utfet not aligned."); + return -EINVAL; + } + + if (uf_info->utftt & (UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT - 1)) { + uccf_err + ("ucc_fast_init: Virtual Fifo register utftt not aligned."); + return -EINVAL; + } + + uccf = (struct ucc_fast_private *) + kmalloc(sizeof(struct ucc_fast_private), GFP_KERNEL); + if (!uccf) { + uccf_err + ("ucc_fast_init: No memory for UCC slow data structure!"); + return -ENOMEM; + } + memset(uccf, 0, sizeof(struct ucc_fast_private)); + + /* Fill fast UCC structure */ + uccf->uf_info = uf_info; + /* Set the PHY base address */ + uccf->uf_regs = + (struct ucc_fast *) ioremap(uf_info->regs, sizeof(struct ucc_fast)); + if (uccf->uf_regs == NULL) { + uccf_err + ("ucc_fast_init: No memory map for UCC slow controller!"); + return -ENOMEM; + } + + uccf->enabled_tx = 0; + uccf->enabled_rx = 0; + uccf->stopped_tx = 0; + uccf->stopped_rx = 0; + uf_regs = uccf->uf_regs; + uccf->p_ucce = (u32 *) & (uf_regs->ucce); + uccf->p_uccm = (u32 *) & (uf_regs->uccm); +#ifdef STATISTICS + uccf->tx_frames = 0; + uccf->rx_frames = 0; + uccf->rx_discarded = 0; +#endif /* STATISTICS */ + + /* Init Guemr register */ + if ((ret = ucc_init_guemr((struct ucc_common *) (uf_regs)))) { + uccf_err("ucc_fast_init: Could not init the guemr register."); + ucc_fast_free(uccf); + return ret; + } + + /* Set UCC to fast type */ + if ((ret = ucc_set_type(uf_info->ucc_num, + (struct ucc_common *) (uf_regs), + UCC_SPEED_TYPE_FAST))) { + uccf_err("ucc_fast_init: Could not set type to fast."); + ucc_fast_free(uccf); + return ret; + } + + uccf->mrblr = uf_info->max_rx_buf_length; + + /* Set GUMR */ + /* For more details see the hardware spec. */ + /* gumr starts as zero. */ + if (uf_info->tci) + gumr |= UCC_FAST_GUMR_TCI; + gumr |= uf_info->ttx_trx; + if (uf_info->cdp) + gumr |= UCC_FAST_GUMR_CDP; + if (uf_info->ctsp) + gumr |= UCC_FAST_GUMR_CTSP; + if (uf_info->cds) + gumr |= UCC_FAST_GUMR_CDS; + if (uf_info->ctss) + gumr |= UCC_FAST_GUMR_CTSS; + if (uf_info->txsy) + gumr |= UCC_FAST_GUMR_TXSY; + if (uf_info->rsyn) + gumr |= UCC_FAST_GUMR_RSYN; + gumr |= uf_info->synl; + if (uf_info->rtsm) + gumr |= UCC_FAST_GUMR_RTSM; + gumr |= uf_info->renc; + if (uf_info->revd) + gumr |= UCC_FAST_GUMR_REVD; + gumr |= uf_info->tenc; + gumr |= uf_info->tcrc; + gumr |= uf_info->mode; + out_be32(&uf_regs->gumr, gumr); + + /* Allocate memory for Tx Virtual Fifo */ + uccf->ucc_fast_tx_virtual_fifo_base_offset = + qe_muram_alloc(uf_info->utfs, UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT); + if (IS_MURAM_ERR(uccf->ucc_fast_tx_virtual_fifo_base_offset)) { + uccf_err + ("ucc_fast_init: Can not allocate MURAM memory for " + "struct ucc_fastx_virtual_fifo_base_offset."); + uccf->ucc_fast_tx_virtual_fifo_base_offset = 0; + ucc_fast_free(uccf); + return -ENOMEM; + } + + /* Allocate memory for Rx Virtual Fifo */ + uccf->ucc_fast_rx_virtual_fifo_base_offset = + qe_muram_alloc(uf_info->urfs + + (u32) + UCC_FAST_RECEIVE_VIRTUAL_FIFO_SIZE_FUDGE_FACTOR, + UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT); + if (IS_MURAM_ERR(uccf->ucc_fast_rx_virtual_fifo_base_offset)) { + uccf_err + ("ucc_fast_init: Can not allocate MURAM memory for " + "ucc_fast_rx_virtual_fifo_base_offset."); + uccf->ucc_fast_rx_virtual_fifo_base_offset = 0; + ucc_fast_free(uccf); + return -ENOMEM; + } + + /* Set Virtual Fifo registers */ + out_be16(&uf_regs->urfs, uf_info->urfs); + out_be16(&uf_regs->urfet, uf_info->urfet); + out_be16(&uf_regs->urfset, uf_info->urfset); + out_be16(&uf_regs->utfs, uf_info->utfs); + out_be16(&uf_regs->utfet, uf_info->utfet); + out_be16(&uf_regs->utftt, uf_info->utftt); + /* utfb, urfb are offsets from MURAM base */ + out_be32(&uf_regs->utfb, uccf->ucc_fast_tx_virtual_fifo_base_offset); + out_be32(&uf_regs->urfb, uccf->ucc_fast_rx_virtual_fifo_base_offset); + + /* Mux clocking */ + /* Grant Support */ + ucc_set_qe_mux_grant(uf_info->ucc_num, uf_info->grant_support); + /* Breakpoint Support */ + ucc_set_qe_mux_bkpt(uf_info->ucc_num, uf_info->brkpt_support); + /* Set Tsa or NMSI mode. */ + ucc_set_qe_mux_tsa(uf_info->ucc_num, uf_info->tsa); + /* If NMSI (not Tsa), set Tx and Rx clock. */ + if (!uf_info->tsa) { + /* Rx clock routing */ + if (uf_info->rx_clock != QE_CLK_NONE) { + if (ucc_set_qe_mux_rxtx + (uf_info->ucc_num, uf_info->rx_clock, + COMM_DIR_RX)) { + uccf_err + ("ucc_fast_init: Illegal value for parameter 'RxClock'."); + ucc_fast_free(uccf); + return -EINVAL; + } + } + /* Tx clock routing */ + if (uf_info->tx_clock != QE_CLK_NONE) { + if (ucc_set_qe_mux_rxtx + (uf_info->ucc_num, uf_info->tx_clock, + COMM_DIR_TX)) { + uccf_err + ("ucc_fast_init: Illegal value for parameter 'TxClock'."); + ucc_fast_free(uccf); + return -EINVAL; + } + } + } + + /* Set interrupt mask register at UCC level. */ + out_be32(&uf_regs->uccm, uf_info->uccm_mask); + + /* First, clear anything pending at UCC level, + * otherwise, old garbage may come through + * as soon as the dam is opened + * Writing '1' clears + */ + out_be32(&uf_regs->ucce, 0xffffffff); + + *uccf_ret = uccf; + return 0; +} + +void ucc_fast_free(struct ucc_fast_private * uccf) +{ + if (!uccf) + return; + + if (uccf->ucc_fast_tx_virtual_fifo_base_offset) + qe_muram_free(uccf->ucc_fast_tx_virtual_fifo_base_offset); + + if (uccf->ucc_fast_rx_virtual_fifo_base_offset) + qe_muram_free(uccf->ucc_fast_rx_virtual_fifo_base_offset); + + kfree(uccf); +} diff --git a/arch/powerpc/sysdev/qe_lib/ucc_slow.c b/arch/powerpc/sysdev/qe_lib/ucc_slow.c new file mode 100644 index 000000000000..1fb88ef7cf06 --- /dev/null +++ b/arch/powerpc/sysdev/qe_lib/ucc_slow.c @@ -0,0 +1,404 @@ +/* + * Copyright (C) 2006 Freescale Semicondutor, Inc. All rights reserved. + * + * Authors: Shlomi Gridish <gridish@freescale.com> + * Li Yang <leoli@freescale.com> + * + * Description: + * QE UCC Slow API Set - UCC Slow specific routines implementations. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/errno.h> +#include <linux/slab.h> +#include <linux/stddef.h> +#include <linux/interrupt.h> + +#include <asm/irq.h> +#include <asm/io.h> +#include <asm/immap_qe.h> +#include <asm/qe.h> + +#include <asm/ucc.h> +#include <asm/ucc_slow.h> + +#define uccs_printk(level, format, arg...) \ + printk(level format "\n", ## arg) + +#define uccs_dbg(format, arg...) \ + uccs_printk(KERN_DEBUG , format , ## arg) +#define uccs_err(format, arg...) \ + uccs_printk(KERN_ERR , format , ## arg) +#define uccs_info(format, arg...) \ + uccs_printk(KERN_INFO , format , ## arg) +#define uccs_warn(format, arg...) \ + uccs_printk(KERN_WARNING , format , ## arg) + +#ifdef UCCS_VERBOSE_DEBUG +#define uccs_vdbg uccs_dbg +#else +#define uccs_vdbg(fmt, args...) do { } while (0) +#endif /* UCCS_VERBOSE_DEBUG */ + +u32 ucc_slow_get_qe_cr_subblock(int uccs_num) +{ + switch (uccs_num) { + case 0: return QE_CR_SUBBLOCK_UCCSLOW1; + case 1: return QE_CR_SUBBLOCK_UCCSLOW2; + case 2: return QE_CR_SUBBLOCK_UCCSLOW3; + case 3: return QE_CR_SUBBLOCK_UCCSLOW4; + case 4: return QE_CR_SUBBLOCK_UCCSLOW5; + case 5: return QE_CR_SUBBLOCK_UCCSLOW6; + case 6: return QE_CR_SUBBLOCK_UCCSLOW7; + case 7: return QE_CR_SUBBLOCK_UCCSLOW8; + default: return QE_CR_SUBBLOCK_INVALID; + } +} + +void ucc_slow_poll_transmitter_now(struct ucc_slow_private * uccs) +{ + out_be16(&uccs->us_regs->utodr, UCC_SLOW_TOD); +} + +void ucc_slow_graceful_stop_tx(struct ucc_slow_private * uccs) +{ + struct ucc_slow_info *us_info = uccs->us_info; + u32 id; + + id = ucc_slow_get_qe_cr_subblock(us_info->ucc_num); + qe_issue_cmd(QE_GRACEFUL_STOP_TX, id, + QE_CR_PROTOCOL_UNSPECIFIED, 0); +} + +void ucc_slow_stop_tx(struct ucc_slow_private * uccs) +{ + struct ucc_slow_info *us_info = uccs->us_info; + u32 id; + + id = ucc_slow_get_qe_cr_subblock(us_info->ucc_num); + qe_issue_cmd(QE_STOP_TX, id, QE_CR_PROTOCOL_UNSPECIFIED, 0); +} + +void ucc_slow_restart_tx(struct ucc_slow_private * uccs) +{ + struct ucc_slow_info *us_info = uccs->us_info; + u32 id; + + id = ucc_slow_get_qe_cr_subblock(us_info->ucc_num); + qe_issue_cmd(QE_RESTART_TX, id, QE_CR_PROTOCOL_UNSPECIFIED, 0); +} + +void ucc_slow_enable(struct ucc_slow_private * uccs, enum comm_dir mode) +{ + struct ucc_slow *us_regs; + u32 gumr_l; + + us_regs = uccs->us_regs; + + /* Enable reception and/or transmission on this UCC. */ + gumr_l = in_be32(&us_regs->gumr_l); + if (mode & COMM_DIR_TX) { + gumr_l |= UCC_SLOW_GUMR_L_ENT; + uccs->enabled_tx = 1; + } + if (mode & COMM_DIR_RX) { + gumr_l |= UCC_SLOW_GUMR_L_ENR; + uccs->enabled_rx = 1; + } + out_be32(&us_regs->gumr_l, gumr_l); +} + +void ucc_slow_disable(struct ucc_slow_private * uccs, enum comm_dir mode) +{ + struct ucc_slow *us_regs; + u32 gumr_l; + + us_regs = uccs->us_regs; + + /* Disable reception and/or transmission on this UCC. */ + gumr_l = in_be32(&us_regs->gumr_l); + if (mode & COMM_DIR_TX) { + gumr_l &= ~UCC_SLOW_GUMR_L_ENT; + uccs->enabled_tx = 0; + } + if (mode & COMM_DIR_RX) { + gumr_l &= ~UCC_SLOW_GUMR_L_ENR; + uccs->enabled_rx = 0; + } + out_be32(&us_regs->gumr_l, gumr_l); +} + +int ucc_slow_init(struct ucc_slow_info * us_info, struct ucc_slow_private ** uccs_ret) +{ + u32 i; + struct ucc_slow *us_regs; + u32 gumr; + u8 function_code = 0; + u8 *bd; + struct ucc_slow_private *uccs; + u32 id; + u32 command; + int ret; + + uccs_vdbg("%s: IN", __FUNCTION__); + + if (!us_info) + return -EINVAL; + + /* check if the UCC port number is in range. */ + if ((us_info->ucc_num < 0) || (us_info->ucc_num > UCC_MAX_NUM - 1)) { + uccs_err("ucc_slow_init: Illagal UCC number!"); + return -EINVAL; + } + + /* + * Set mrblr + * Check that 'max_rx_buf_length' is properly aligned (4), unless + * rfw is 1, meaning that QE accepts one byte at a time, unlike normal + * case when QE accepts 32 bits at a time. + */ + if ((!us_info->rfw) && + (us_info->max_rx_buf_length & (UCC_SLOW_MRBLR_ALIGNMENT - 1))) { + uccs_err("max_rx_buf_length not aligned."); + return -EINVAL; + } + + uccs = (struct ucc_slow_private *) + kmalloc(sizeof(struct ucc_slow_private), GFP_KERNEL); + if (!uccs) { + uccs_err + ("ucc_slow_init: No memory for UCC slow data structure!"); + return -ENOMEM; + } + memset(uccs, 0, sizeof(struct ucc_slow_private)); + + /* Fill slow UCC structure */ + uccs->us_info = us_info; + uccs->saved_uccm = 0; + uccs->p_rx_frame = 0; + uccs->us_regs = us_info->us_regs; + us_regs = uccs->us_regs; + uccs->p_ucce = (u16 *) & (us_regs->ucce); + uccs->p_uccm = (u16 *) & (us_regs->uccm); +#ifdef STATISTICS + uccs->rx_frames = 0; + uccs->tx_frames = 0; + uccs->rx_discarded = 0; +#endif /* STATISTICS */ + + /* Get PRAM base */ + uccs->us_pram_offset = qe_muram_alloc(UCC_SLOW_PRAM_SIZE, + ALIGNMENT_OF_UCC_SLOW_PRAM); + if (IS_MURAM_ERR(uccs->us_pram_offset)) { + uccs_err + ("ucc_slow_init: Can not allocate MURAM memory " + "for Slow UCC."); + ucc_slow_free(uccs); + return -ENOMEM; + } + id = ucc_slow_get_qe_cr_subblock(us_info->ucc_num); + qe_issue_cmd(QE_ASSIGN_PAGE_TO_DEVICE, id, QE_CR_PROTOCOL_UNSPECIFIED, + (u32) uccs->us_pram_offset); + + uccs->us_pram = qe_muram_addr(uccs->us_pram_offset); + + /* Init Guemr register */ + if ((ret = ucc_init_guemr((struct ucc_common *) (us_info->us_regs)))) { + uccs_err("ucc_slow_init: Could not init the guemr register."); + ucc_slow_free(uccs); + return ret; + } + + /* Set UCC to slow type */ + if ((ret = ucc_set_type(us_info->ucc_num, + (struct ucc_common *) (us_info->us_regs), + UCC_SPEED_TYPE_SLOW))) { + uccs_err("ucc_slow_init: Could not init the guemr register."); + ucc_slow_free(uccs); + return ret; + } + + out_be16(&uccs->us_pram->mrblr, us_info->max_rx_buf_length); + + INIT_LIST_HEAD(&uccs->confQ); + + /* Allocate BDs. */ + uccs->rx_base_offset = + qe_muram_alloc(us_info->rx_bd_ring_len * sizeof(struct qe_bd), + QE_ALIGNMENT_OF_BD); + if (IS_MURAM_ERR(uccs->rx_base_offset)) { + uccs_err("ucc_slow_init: No memory for Rx BD's."); + uccs->rx_base_offset = 0; + ucc_slow_free(uccs); + return -ENOMEM; + } + + uccs->tx_base_offset = + qe_muram_alloc(us_info->tx_bd_ring_len * sizeof(struct qe_bd), + QE_ALIGNMENT_OF_BD); + if (IS_MURAM_ERR(uccs->tx_base_offset)) { + uccs_err("ucc_slow_init: No memory for Tx BD's."); + uccs->tx_base_offset = 0; + ucc_slow_free(uccs); + return -ENOMEM; + } + + /* Init Tx bds */ + bd = uccs->confBd = uccs->tx_bd = qe_muram_addr(uccs->tx_base_offset); + for (i = 0; i < us_info->tx_bd_ring_len; i++) { + /* clear bd buffer */ + out_be32(&(((struct qe_bd *)bd)->buf), 0); + /* set bd status and length */ + out_be32((u32*)bd, 0); + bd += sizeof(struct qe_bd); + } + bd -= sizeof(struct qe_bd); + /* set bd status and length */ + out_be32((u32*)bd, T_W); /* for last BD set Wrap bit */ + + /* Init Rx bds */ + bd = uccs->rx_bd = qe_muram_addr(uccs->rx_base_offset); + for (i = 0; i < us_info->rx_bd_ring_len; i++) { + /* set bd status and length */ + out_be32((u32*)bd, 0); + /* clear bd buffer */ + out_be32(&(((struct qe_bd *)bd)->buf), 0); + bd += sizeof(struct qe_bd); + } + bd -= sizeof(struct qe_bd); + /* set bd status and length */ + out_be32((u32*)bd, R_W); /* for last BD set Wrap bit */ + + /* Set GUMR (For more details see the hardware spec.). */ + /* gumr_h */ + gumr = 0; + gumr |= us_info->tcrc; + if (us_info->cdp) + gumr |= UCC_SLOW_GUMR_H_CDP; + if (us_info->ctsp) + gumr |= UCC_SLOW_GUMR_H_CTSP; + if (us_info->cds) + gumr |= UCC_SLOW_GUMR_H_CDS; + if (us_info->ctss) + gumr |= UCC_SLOW_GUMR_H_CTSS; + if (us_info->tfl) + gumr |= UCC_SLOW_GUMR_H_TFL; + if (us_info->rfw) + gumr |= UCC_SLOW_GUMR_H_RFW; + if (us_info->txsy) + gumr |= UCC_SLOW_GUMR_H_TXSY; + if (us_info->rtsm) + gumr |= UCC_SLOW_GUMR_H_RTSM; + out_be32(&us_regs->gumr_h, gumr); + + /* gumr_l */ + gumr = 0; + if (us_info->tci) + gumr |= UCC_SLOW_GUMR_L_TCI; + if (us_info->rinv) + gumr |= UCC_SLOW_GUMR_L_RINV; + if (us_info->tinv) + gumr |= UCC_SLOW_GUMR_L_TINV; + if (us_info->tend) + gumr |= UCC_SLOW_GUMR_L_TEND; + gumr |= us_info->tdcr; + gumr |= us_info->rdcr; + gumr |= us_info->tenc; + gumr |= us_info->renc; + gumr |= us_info->diag; + gumr |= us_info->mode; + out_be32(&us_regs->gumr_l, gumr); + + /* Function code registers */ + /* function_code has initial value 0 */ + + /* if the data is in cachable memory, the 'global' */ + /* in the function code should be set. */ + function_code |= us_info->data_mem_part; + function_code |= QE_BMR_BYTE_ORDER_BO_MOT; /* Required for QE */ + uccs->us_pram->tfcr = function_code; + uccs->us_pram->rfcr = function_code; + + /* rbase, tbase are offsets from MURAM base */ + out_be16(&uccs->us_pram->rbase, uccs->us_pram_offset); + out_be16(&uccs->us_pram->tbase, uccs->us_pram_offset); + + /* Mux clocking */ + /* Grant Support */ + ucc_set_qe_mux_grant(us_info->ucc_num, us_info->grant_support); + /* Breakpoint Support */ + ucc_set_qe_mux_bkpt(us_info->ucc_num, us_info->brkpt_support); + /* Set Tsa or NMSI mode. */ + ucc_set_qe_mux_tsa(us_info->ucc_num, us_info->tsa); + /* If NMSI (not Tsa), set Tx and Rx clock. */ + if (!us_info->tsa) { + /* Rx clock routing */ + if (ucc_set_qe_mux_rxtx + (us_info->ucc_num, us_info->rx_clock, COMM_DIR_RX)) { + uccs_err + ("ucc_slow_init: Illegal value for parameter" + " 'RxClock'."); + ucc_slow_free(uccs); + return -EINVAL; + } + /* Tx clock routing */ + if (ucc_set_qe_mux_rxtx(us_info->ucc_num, + us_info->tx_clock, COMM_DIR_TX)) { + uccs_err + ("ucc_slow_init: Illegal value for parameter " + "'TxClock'."); + ucc_slow_free(uccs); + return -EINVAL; + } + } + + /* + * INTERRUPTS + */ + /* Set interrupt mask register at UCC level. */ + out_be16(&us_regs->uccm, us_info->uccm_mask); + + /* First, clear anything pending at UCC level, */ + /* otherwise, old garbage may come through */ + /* as soon as the dam is opened. */ + + /* Writing '1' clears */ + out_be16(&us_regs->ucce, 0xffff); + + /* Issue QE Init command */ + if (us_info->init_tx && us_info->init_rx) + command = QE_INIT_TX_RX; + else if (us_info->init_tx) + command = QE_INIT_TX; + else + command = QE_INIT_RX; /* We know at least one is TRUE */ + id = ucc_slow_get_qe_cr_subblock(us_info->ucc_num); + qe_issue_cmd(command, id, QE_CR_PROTOCOL_UNSPECIFIED, 0); + + *uccs_ret = uccs; + return 0; +} + +void ucc_slow_free(struct ucc_slow_private * uccs) +{ + if (!uccs) + return; + + if (uccs->rx_base_offset) + qe_muram_free(uccs->rx_base_offset); + + if (uccs->tx_base_offset) + qe_muram_free(uccs->tx_base_offset); + + if (uccs->us_pram) { + qe_muram_free(uccs->us_pram_offset); + uccs->us_pram = NULL; + } + + kfree(uccs); +} diff --git a/arch/powerpc/xmon/xmon.c b/arch/powerpc/xmon/xmon.c index 8adad1444a51..708236f34746 100644 --- a/arch/powerpc/xmon/xmon.c +++ b/arch/powerpc/xmon/xmon.c @@ -2,6 +2,8 @@ * Routines providing a simple monitor for use on the PowerMac. * * Copyright (C) 1996-2005 Paul Mackerras. + * Copyright (C) 2001 PPC64 Team, IBM Corp + * Copyrignt (C) 2006 Michael Ellerman, IBM Corp * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -503,7 +505,7 @@ static int xmon_core(struct pt_regs *regs, int fromipi) mtmsr(msr); /* restore interrupt enable */ - return cmd != 'X'; + return cmd != 'X' && cmd != EOF; } int xmon(struct pt_regs *excp) @@ -2597,3 +2599,34 @@ static int __init setup_xmon_sysrq(void) } __initcall(setup_xmon_sysrq); #endif /* CONFIG_MAGIC_SYSRQ */ + +int __initdata xmon_early, xmon_off; + +static int __init early_parse_xmon(char *p) +{ + if (!p || strncmp(p, "early", 5) == 0) { + /* just "xmon" is equivalent to "xmon=early" */ + xmon_init(1); + xmon_early = 1; + } else if (strncmp(p, "on", 2) == 0) + xmon_init(1); + else if (strncmp(p, "off", 3) == 0) + xmon_off = 1; + else if (strncmp(p, "nobt", 4) == 0) + xmon_no_auto_backtrace = 1; + else + return 1; + + return 0; +} +early_param("xmon", early_parse_xmon); + +void __init xmon_setup(void) +{ +#ifdef CONFIG_XMON_DEFAULT + if (!xmon_off) + xmon_init(1); +#endif + if (xmon_early) + debugger(NULL); +} diff --git a/drivers/block/swim3.c b/drivers/block/swim3.c index f2305ee792a1..fdc8f892eb86 100644 --- a/drivers/block/swim3.c +++ b/drivers/block/swim3.c @@ -636,7 +636,7 @@ static irqreturn_t swim3_interrupt(int irq, void *dev_id, struct pt_regs *regs) intr = in_8(&sw->intr); err = (intr & ERROR_INTR)? in_8(&sw->error): 0; if ((intr & ERROR_INTR) && fs->state != do_transfer) - printk(KERN_ERR "swim3_interrupt, state=%d, dir=%lx, intr=%x, err=%x\n", + printk(KERN_ERR "swim3_interrupt, state=%d, dir=%x, intr=%x, err=%x\n", fs->state, rq_data_dir(fd_req), intr, err); switch (fs->state) { case locating: @@ -742,7 +742,7 @@ static irqreturn_t swim3_interrupt(int irq, void *dev_id, struct pt_regs *regs) if ((stat & ACTIVE) == 0 || resid != 0) { /* musta been an error */ printk(KERN_ERR "swim3: fd dma: stat=%x resid=%d\n", stat, resid); - printk(KERN_ERR " state=%d, dir=%lx, intr=%x, err=%x\n", + printk(KERN_ERR " state=%d, dir=%x, intr=%x, err=%x\n", fs->state, rq_data_dir(fd_req), intr, err); end_request(fd_req, 0); fs->state = idle; diff --git a/drivers/char/hvc_iseries.c b/drivers/char/hvc_iseries.c index 8b6f197e5f8c..f144a947bd17 100644 --- a/drivers/char/hvc_iseries.c +++ b/drivers/char/hvc_iseries.c @@ -29,6 +29,7 @@ #include <asm/hvconsole.h> #include <asm/vio.h> #include <asm/prom.h> +#include <asm/firmware.h> #include <asm/iseries/vio.h> #include <asm/iseries/hv_call.h> #include <asm/iseries/hv_lp_config.h> @@ -488,6 +489,9 @@ static int hvc_vio_init(void) atomic_t wait_flag; int rc; + if (!firmware_has_feature(FW_FEATURE_ISERIES)) + return -EIO; + /* +2 for fudge */ rc = viopath_open(HvLpConfig_getPrimaryLpIndex(), viomajorsubtype_chario, VIOCHAR_WINDOW + 2); @@ -562,7 +566,7 @@ static int hvc_find_vtys(void) for (vty = of_find_node_by_name(NULL, "vty"); vty != NULL; vty = of_find_node_by_name(vty, "vty")) { - uint32_t *vtermno; + const uint32_t *vtermno; /* We have statically defined space for only a certain number * of console adapters. @@ -571,7 +575,7 @@ static int hvc_find_vtys(void) (num_found >= VTTY_PORTS)) break; - vtermno = (uint32_t *)get_property(vty, "reg", NULL); + vtermno = get_property(vty, "reg", NULL); if (!vtermno) continue; diff --git a/drivers/char/hvc_vio.c b/drivers/char/hvc_vio.c index cc95941148fb..f9c00844d2bf 100644 --- a/drivers/char/hvc_vio.c +++ b/drivers/char/hvc_vio.c @@ -35,6 +35,7 @@ #include <asm/hvconsole.h> #include <asm/vio.h> #include <asm/prom.h> +#include <asm/firmware.h> #include "hvc_console.h" @@ -120,6 +121,9 @@ static int hvc_vio_init(void) { int rc; + if (firmware_has_feature(FW_FEATURE_ISERIES)) + return -EIO; + /* Register as a vio device to receive callbacks */ rc = vio_register_driver(&hvc_vio_driver); diff --git a/include/asm-powerpc/firmware.h b/include/asm-powerpc/firmware.h index 77069df92bf8..1022737f4f34 100644 --- a/include/asm-powerpc/firmware.h +++ b/include/asm-powerpc/firmware.h @@ -14,34 +14,36 @@ #ifdef __KERNEL__ -#ifndef __ASSEMBLY__ +#include <asm/asm-compat.h> /* firmware feature bitmask values */ #define FIRMWARE_MAX_FEATURES 63 -#define FW_FEATURE_PFT (1UL<<0) -#define FW_FEATURE_TCE (1UL<<1) -#define FW_FEATURE_SPRG0 (1UL<<2) -#define FW_FEATURE_DABR (1UL<<3) -#define FW_FEATURE_COPY (1UL<<4) -#define FW_FEATURE_ASR (1UL<<5) -#define FW_FEATURE_DEBUG (1UL<<6) -#define FW_FEATURE_TERM (1UL<<7) -#define FW_FEATURE_PERF (1UL<<8) -#define FW_FEATURE_DUMP (1UL<<9) -#define FW_FEATURE_INTERRUPT (1UL<<10) -#define FW_FEATURE_MIGRATE (1UL<<11) -#define FW_FEATURE_PERFMON (1UL<<12) -#define FW_FEATURE_CRQ (1UL<<13) -#define FW_FEATURE_VIO (1UL<<14) -#define FW_FEATURE_RDMA (1UL<<15) -#define FW_FEATURE_LLAN (1UL<<16) -#define FW_FEATURE_BULK (1UL<<17) -#define FW_FEATURE_XDABR (1UL<<18) -#define FW_FEATURE_MULTITCE (1UL<<19) -#define FW_FEATURE_SPLPAR (1UL<<20) -#define FW_FEATURE_ISERIES (1UL<<21) -#define FW_FEATURE_LPAR (1UL<<22) +#define FW_FEATURE_PFT ASM_CONST(0x0000000000000001) +#define FW_FEATURE_TCE ASM_CONST(0x0000000000000002) +#define FW_FEATURE_SPRG0 ASM_CONST(0x0000000000000004) +#define FW_FEATURE_DABR ASM_CONST(0x0000000000000008) +#define FW_FEATURE_COPY ASM_CONST(0x0000000000000010) +#define FW_FEATURE_ASR ASM_CONST(0x0000000000000020) +#define FW_FEATURE_DEBUG ASM_CONST(0x0000000000000040) +#define FW_FEATURE_TERM ASM_CONST(0x0000000000000080) +#define FW_FEATURE_PERF ASM_CONST(0x0000000000000100) +#define FW_FEATURE_DUMP ASM_CONST(0x0000000000000200) +#define FW_FEATURE_INTERRUPT ASM_CONST(0x0000000000000400) +#define FW_FEATURE_MIGRATE ASM_CONST(0x0000000000000800) +#define FW_FEATURE_PERFMON ASM_CONST(0x0000000000001000) +#define FW_FEATURE_CRQ ASM_CONST(0x0000000000002000) +#define FW_FEATURE_VIO ASM_CONST(0x0000000000004000) +#define FW_FEATURE_RDMA ASM_CONST(0x0000000000008000) +#define FW_FEATURE_LLAN ASM_CONST(0x0000000000010000) +#define FW_FEATURE_BULK ASM_CONST(0x0000000000020000) +#define FW_FEATURE_XDABR ASM_CONST(0x0000000000040000) +#define FW_FEATURE_MULTITCE ASM_CONST(0x0000000000080000) +#define FW_FEATURE_SPLPAR ASM_CONST(0x0000000000100000) +#define FW_FEATURE_ISERIES ASM_CONST(0x0000000000200000) +#define FW_FEATURE_LPAR ASM_CONST(0x0000000000400000) + +#ifndef __ASSEMBLY__ enum { #ifdef CONFIG_PPC64 @@ -94,6 +96,23 @@ extern void machine_check_fwnmi(void); /* This is true if we are using the firmware NMI handler (typically LPAR) */ extern int fwnmi_active; +#else /* __ASSEMBLY__ */ + +#define BEGIN_FW_FTR_SECTION 96: + +#define END_FW_FTR_SECTION(msk, val) \ +97: \ + .section __fw_ftr_fixup,"a"; \ + .align 3; \ + .llong msk; \ + .llong val; \ + .llong 96b; \ + .llong 97b; \ + .previous + +#define END_FW_FTR_SECTION_IFSET(msk) END_FW_FTR_SECTION((msk), (msk)) +#define END_FW_FTR_SECTION_IFCLR(msk) END_FW_FTR_SECTION((msk), 0) + #endif /* __ASSEMBLY__ */ #endif /* __KERNEL__ */ #endif /* __ASM_POWERPC_FIRMWARE_H */ diff --git a/include/asm-powerpc/immap_qe.h b/include/asm-powerpc/immap_qe.h new file mode 100644 index 000000000000..ce12f85fff9b --- /dev/null +++ b/include/asm-powerpc/immap_qe.h @@ -0,0 +1,477 @@ +/* + * include/asm-powerpc/immap_qe.h + * + * QUICC Engine (QE) Internal Memory Map. + * The Internal Memory Map for devices with QE on them. This + * is the superset of all QE devices (8360, etc.). + + * Copyright (C) 2006. Freescale Semicondutor, Inc. All rights reserved. + * + * Authors: Shlomi Gridish <gridish@freescale.com> + * Li Yang <leoli@freescale.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#ifndef _ASM_POWERPC_IMMAP_QE_H +#define _ASM_POWERPC_IMMAP_QE_H +#ifdef __KERNEL__ + +#include <linux/kernel.h> + +#define QE_IMMAP_SIZE (1024 * 1024) /* 1MB from 1MB+IMMR */ + +/* QE I-RAM */ +struct qe_iram { + __be32 iadd; /* I-RAM Address Register */ + __be32 idata; /* I-RAM Data Register */ + u8 res0[0x78]; +} __attribute__ ((packed)); + +/* QE Interrupt Controller */ +struct qe_ic_regs { + __be32 qicr; + __be32 qivec; + __be32 qripnr; + __be32 qipnr; + __be32 qipxcc; + __be32 qipycc; + __be32 qipwcc; + __be32 qipzcc; + __be32 qimr; + __be32 qrimr; + __be32 qicnr; + u8 res0[0x4]; + __be32 qiprta; + __be32 qiprtb; + u8 res1[0x4]; + __be32 qricr; + u8 res2[0x20]; + __be32 qhivec; + u8 res3[0x1C]; +} __attribute__ ((packed)); + +/* Communications Processor */ +struct cp_qe { + __be32 cecr; /* QE command register */ + __be32 ceccr; /* QE controller configuration register */ + __be32 cecdr; /* QE command data register */ + u8 res0[0xA]; + __be16 ceter; /* QE timer event register */ + u8 res1[0x2]; + __be16 cetmr; /* QE timers mask register */ + __be32 cetscr; /* QE time-stamp timer control register */ + __be32 cetsr1; /* QE time-stamp register 1 */ + __be32 cetsr2; /* QE time-stamp register 2 */ + u8 res2[0x8]; + __be32 cevter; /* QE virtual tasks event register */ + __be32 cevtmr; /* QE virtual tasks mask register */ + __be16 cercr; /* QE RAM control register */ + u8 res3[0x2]; + u8 res4[0x24]; + __be16 ceexe1; /* QE external request 1 event register */ + u8 res5[0x2]; + __be16 ceexm1; /* QE external request 1 mask register */ + u8 res6[0x2]; + __be16 ceexe2; /* QE external request 2 event register */ + u8 res7[0x2]; + __be16 ceexm2; /* QE external request 2 mask register */ + u8 res8[0x2]; + __be16 ceexe3; /* QE external request 3 event register */ + u8 res9[0x2]; + __be16 ceexm3; /* QE external request 3 mask register */ + u8 res10[0x2]; + __be16 ceexe4; /* QE external request 4 event register */ + u8 res11[0x2]; + __be16 ceexm4; /* QE external request 4 mask register */ + u8 res12[0x2]; + u8 res13[0x280]; +} __attribute__ ((packed)); + +/* QE Multiplexer */ +struct qe_mux { + __be32 cmxgcr; /* CMX general clock route register */ + __be32 cmxsi1cr_l; /* CMX SI1 clock route low register */ + __be32 cmxsi1cr_h; /* CMX SI1 clock route high register */ + __be32 cmxsi1syr; /* CMX SI1 SYNC route register */ + __be32 cmxucr1; /* CMX UCC1, UCC3 clock route register */ + __be32 cmxucr2; /* CMX UCC5, UCC7 clock route register */ + __be32 cmxucr3; /* CMX UCC2, UCC4 clock route register */ + __be32 cmxucr4; /* CMX UCC6, UCC8 clock route register */ + __be32 cmxupcr; /* CMX UPC clock route register */ + u8 res0[0x1C]; +} __attribute__ ((packed)); + +/* QE Timers */ +struct qe_timers { + u8 gtcfr1; /* Timer 1 and Timer 2 global config register*/ + u8 res0[0x3]; + u8 gtcfr2; /* Timer 3 and timer 4 global config register*/ + u8 res1[0xB]; + __be16 gtmdr1; /* Timer 1 mode register */ + __be16 gtmdr2; /* Timer 2 mode register */ + __be16 gtrfr1; /* Timer 1 reference register */ + __be16 gtrfr2; /* Timer 2 reference register */ + __be16 gtcpr1; /* Timer 1 capture register */ + __be16 gtcpr2; /* Timer 2 capture register */ + __be16 gtcnr1; /* Timer 1 counter */ + __be16 gtcnr2; /* Timer 2 counter */ + __be16 gtmdr3; /* Timer 3 mode register */ + __be16 gtmdr4; /* Timer 4 mode register */ + __be16 gtrfr3; /* Timer 3 reference register */ + __be16 gtrfr4; /* Timer 4 reference register */ + __be16 gtcpr3; /* Timer 3 capture register */ + __be16 gtcpr4; /* Timer 4 capture register */ + __be16 gtcnr3; /* Timer 3 counter */ + __be16 gtcnr4; /* Timer 4 counter */ + __be16 gtevr1; /* Timer 1 event register */ + __be16 gtevr2; /* Timer 2 event register */ + __be16 gtevr3; /* Timer 3 event register */ + __be16 gtevr4; /* Timer 4 event register */ + __be16 gtps; /* Timer 1 prescale register */ + u8 res2[0x46]; +} __attribute__ ((packed)); + +/* BRG */ +struct qe_brg { + __be32 brgc1; /* BRG1 configuration register */ + __be32 brgc2; /* BRG2 configuration register */ + __be32 brgc3; /* BRG3 configuration register */ + __be32 brgc4; /* BRG4 configuration register */ + __be32 brgc5; /* BRG5 configuration register */ + __be32 brgc6; /* BRG6 configuration register */ + __be32 brgc7; /* BRG7 configuration register */ + __be32 brgc8; /* BRG8 configuration register */ + __be32 brgc9; /* BRG9 configuration register */ + __be32 brgc10; /* BRG10 configuration register */ + __be32 brgc11; /* BRG11 configuration register */ + __be32 brgc12; /* BRG12 configuration register */ + __be32 brgc13; /* BRG13 configuration register */ + __be32 brgc14; /* BRG14 configuration register */ + __be32 brgc15; /* BRG15 configuration register */ + __be32 brgc16; /* BRG16 configuration register */ + u8 res0[0x40]; +} __attribute__ ((packed)); + +/* SPI */ +struct spi { + u8 res0[0x20]; + __be32 spmode; /* SPI mode register */ + u8 res1[0x2]; + u8 spie; /* SPI event register */ + u8 res2[0x1]; + u8 res3[0x2]; + u8 spim; /* SPI mask register */ + u8 res4[0x1]; + u8 res5[0x1]; + u8 spcom; /* SPI command register */ + u8 res6[0x2]; + __be32 spitd; /* SPI transmit data register (cpu mode) */ + __be32 spird; /* SPI receive data register (cpu mode) */ + u8 res7[0x8]; +} __attribute__ ((packed)); + +/* SI */ +struct si1 { + __be16 siamr1; /* SI1 TDMA mode register */ + __be16 sibmr1; /* SI1 TDMB mode register */ + __be16 sicmr1; /* SI1 TDMC mode register */ + __be16 sidmr1; /* SI1 TDMD mode register */ + u8 siglmr1_h; /* SI1 global mode register high */ + u8 res0[0x1]; + u8 sicmdr1_h; /* SI1 command register high */ + u8 res2[0x1]; + u8 sistr1_h; /* SI1 status register high */ + u8 res3[0x1]; + __be16 sirsr1_h; /* SI1 RAM shadow address register high */ + u8 sitarc1; /* SI1 RAM counter Tx TDMA */ + u8 sitbrc1; /* SI1 RAM counter Tx TDMB */ + u8 sitcrc1; /* SI1 RAM counter Tx TDMC */ + u8 sitdrc1; /* SI1 RAM counter Tx TDMD */ + u8 sirarc1; /* SI1 RAM counter Rx TDMA */ + u8 sirbrc1; /* SI1 RAM counter Rx TDMB */ + u8 sircrc1; /* SI1 RAM counter Rx TDMC */ + u8 sirdrc1; /* SI1 RAM counter Rx TDMD */ + u8 res4[0x8]; + __be16 siemr1; /* SI1 TDME mode register 16 bits */ + __be16 sifmr1; /* SI1 TDMF mode register 16 bits */ + __be16 sigmr1; /* SI1 TDMG mode register 16 bits */ + __be16 sihmr1; /* SI1 TDMH mode register 16 bits */ + u8 siglmg1_l; /* SI1 global mode register low 8 bits */ + u8 res5[0x1]; + u8 sicmdr1_l; /* SI1 command register low 8 bits */ + u8 res6[0x1]; + u8 sistr1_l; /* SI1 status register low 8 bits */ + u8 res7[0x1]; + __be16 sirsr1_l; /* SI1 RAM shadow address register low 16 bits*/ + u8 siterc1; /* SI1 RAM counter Tx TDME 8 bits */ + u8 sitfrc1; /* SI1 RAM counter Tx TDMF 8 bits */ + u8 sitgrc1; /* SI1 RAM counter Tx TDMG 8 bits */ + u8 sithrc1; /* SI1 RAM counter Tx TDMH 8 bits */ + u8 sirerc1; /* SI1 RAM counter Rx TDME 8 bits */ + u8 sirfrc1; /* SI1 RAM counter Rx TDMF 8 bits */ + u8 sirgrc1; /* SI1 RAM counter Rx TDMG 8 bits */ + u8 sirhrc1; /* SI1 RAM counter Rx TDMH 8 bits */ + u8 res8[0x8]; + __be32 siml1; /* SI1 multiframe limit register */ + u8 siedm1; /* SI1 extended diagnostic mode register */ + u8 res9[0xBB]; +} __attribute__ ((packed)); + +/* SI Routing Tables */ +struct sir { + u8 tx[0x400]; + u8 rx[0x400]; + u8 res0[0x800]; +} __attribute__ ((packed)); + +/* USB Controller */ +struct usb_ctlr { + u8 usb_usmod; + u8 usb_usadr; + u8 usb_uscom; + u8 res1[1]; + __be16 usb_usep1; + __be16 usb_usep2; + __be16 usb_usep3; + __be16 usb_usep4; + u8 res2[4]; + __be16 usb_usber; + u8 res3[2]; + __be16 usb_usbmr; + u8 res4[1]; + u8 usb_usbs; + __be16 usb_ussft; + u8 res5[2]; + __be16 usb_usfrn; + u8 res6[0x22]; +} __attribute__ ((packed)); + +/* MCC */ +struct mcc { + __be32 mcce; /* MCC event register */ + __be32 mccm; /* MCC mask register */ + __be32 mccf; /* MCC configuration register */ + __be32 merl; /* MCC emergency request level register */ + u8 res0[0xF0]; +} __attribute__ ((packed)); + +/* QE UCC Slow */ +struct ucc_slow { + __be32 gumr_l; /* UCCx general mode register (low) */ + __be32 gumr_h; /* UCCx general mode register (high) */ + __be16 upsmr; /* UCCx protocol-specific mode register */ + u8 res0[0x2]; + __be16 utodr; /* UCCx transmit on demand register */ + __be16 udsr; /* UCCx data synchronization register */ + __be16 ucce; /* UCCx event register */ + u8 res1[0x2]; + __be16 uccm; /* UCCx mask register */ + u8 res2[0x1]; + u8 uccs; /* UCCx status register */ + u8 res3[0x24]; + __be16 utpt; + u8 guemr; /* UCC general extended mode register */ + u8 res4[0x200 - 0x091]; +} __attribute__ ((packed)); + +/* QE UCC Fast */ +struct ucc_fast { + __be32 gumr; /* UCCx general mode register */ + __be32 upsmr; /* UCCx protocol-specific mode register */ + __be16 utodr; /* UCCx transmit on demand register */ + u8 res0[0x2]; + __be16 udsr; /* UCCx data synchronization register */ + u8 res1[0x2]; + __be32 ucce; /* UCCx event register */ + __be32 uccm; /* UCCx mask register */ + u8 uccs; /* UCCx status register */ + u8 res2[0x7]; + __be32 urfb; /* UCC receive FIFO base */ + __be16 urfs; /* UCC receive FIFO size */ + u8 res3[0x2]; + __be16 urfet; /* UCC receive FIFO emergency threshold */ + __be16 urfset; /* UCC receive FIFO special emergency + threshold */ + __be32 utfb; /* UCC transmit FIFO base */ + __be16 utfs; /* UCC transmit FIFO size */ + u8 res4[0x2]; + __be16 utfet; /* UCC transmit FIFO emergency threshold */ + u8 res5[0x2]; + __be16 utftt; /* UCC transmit FIFO transmit threshold */ + u8 res6[0x2]; + __be16 utpt; /* UCC transmit polling timer */ + u8 res7[0x2]; + __be32 urtry; /* UCC retry counter register */ + u8 res8[0x4C]; + u8 guemr; /* UCC general extended mode register */ + u8 res9[0x100 - 0x091]; +} __attribute__ ((packed)); + +/* QE UCC */ +struct ucc_common { + u8 res1[0x90]; + u8 guemr; + u8 res2[0x200 - 0x091]; +} __attribute__ ((packed)); + +struct ucc { + union { + struct ucc_slow slow; + struct ucc_fast fast; + struct ucc_common common; + }; +} __attribute__ ((packed)); + +/* MultiPHY UTOPIA POS Controllers (UPC) */ +struct upc { + __be32 upgcr; /* UTOPIA/POS general configuration register */ + __be32 uplpa; /* UTOPIA/POS last PHY address */ + __be32 uphec; /* ATM HEC register */ + __be32 upuc; /* UTOPIA/POS UCC configuration */ + __be32 updc1; /* UTOPIA/POS device 1 configuration */ + __be32 updc2; /* UTOPIA/POS device 2 configuration */ + __be32 updc3; /* UTOPIA/POS device 3 configuration */ + __be32 updc4; /* UTOPIA/POS device 4 configuration */ + __be32 upstpa; /* UTOPIA/POS STPA threshold */ + u8 res0[0xC]; + __be32 updrs1_h; /* UTOPIA/POS device 1 rate select */ + __be32 updrs1_l; /* UTOPIA/POS device 1 rate select */ + __be32 updrs2_h; /* UTOPIA/POS device 2 rate select */ + __be32 updrs2_l; /* UTOPIA/POS device 2 rate select */ + __be32 updrs3_h; /* UTOPIA/POS device 3 rate select */ + __be32 updrs3_l; /* UTOPIA/POS device 3 rate select */ + __be32 updrs4_h; /* UTOPIA/POS device 4 rate select */ + __be32 updrs4_l; /* UTOPIA/POS device 4 rate select */ + __be32 updrp1; /* UTOPIA/POS device 1 receive priority low */ + __be32 updrp2; /* UTOPIA/POS device 2 receive priority low */ + __be32 updrp3; /* UTOPIA/POS device 3 receive priority low */ + __be32 updrp4; /* UTOPIA/POS device 4 receive priority low */ + __be32 upde1; /* UTOPIA/POS device 1 event */ + __be32 upde2; /* UTOPIA/POS device 2 event */ + __be32 upde3; /* UTOPIA/POS device 3 event */ + __be32 upde4; /* UTOPIA/POS device 4 event */ + __be16 uprp1; + __be16 uprp2; + __be16 uprp3; + __be16 uprp4; + u8 res1[0x8]; + __be16 uptirr1_0; /* Device 1 transmit internal rate 0 */ + __be16 uptirr1_1; /* Device 1 transmit internal rate 1 */ + __be16 uptirr1_2; /* Device 1 transmit internal rate 2 */ + __be16 uptirr1_3; /* Device 1 transmit internal rate 3 */ + __be16 uptirr2_0; /* Device 2 transmit internal rate 0 */ + __be16 uptirr2_1; /* Device 2 transmit internal rate 1 */ + __be16 uptirr2_2; /* Device 2 transmit internal rate 2 */ + __be16 uptirr2_3; /* Device 2 transmit internal rate 3 */ + __be16 uptirr3_0; /* Device 3 transmit internal rate 0 */ + __be16 uptirr3_1; /* Device 3 transmit internal rate 1 */ + __be16 uptirr3_2; /* Device 3 transmit internal rate 2 */ + __be16 uptirr3_3; /* Device 3 transmit internal rate 3 */ + __be16 uptirr4_0; /* Device 4 transmit internal rate 0 */ + __be16 uptirr4_1; /* Device 4 transmit internal rate 1 */ + __be16 uptirr4_2; /* Device 4 transmit internal rate 2 */ + __be16 uptirr4_3; /* Device 4 transmit internal rate 3 */ + __be32 uper1; /* Device 1 port enable register */ + __be32 uper2; /* Device 2 port enable register */ + __be32 uper3; /* Device 3 port enable register */ + __be32 uper4; /* Device 4 port enable register */ + u8 res2[0x150]; +} __attribute__ ((packed)); + +/* SDMA */ +struct sdma { + __be32 sdsr; /* Serial DMA status register */ + __be32 sdmr; /* Serial DMA mode register */ + __be32 sdtr1; /* SDMA system bus threshold register */ + __be32 sdtr2; /* SDMA secondary bus threshold register */ + __be32 sdhy1; /* SDMA system bus hysteresis register */ + __be32 sdhy2; /* SDMA secondary bus hysteresis register */ + __be32 sdta1; /* SDMA system bus address register */ + __be32 sdta2; /* SDMA secondary bus address register */ + __be32 sdtm1; /* SDMA system bus MSNUM register */ + __be32 sdtm2; /* SDMA secondary bus MSNUM register */ + u8 res0[0x10]; + __be32 sdaqr; /* SDMA address bus qualify register */ + __be32 sdaqmr; /* SDMA address bus qualify mask register */ + u8 res1[0x4]; + __be32 sdebcr; /* SDMA CAM entries base register */ + u8 res2[0x38]; +} __attribute__ ((packed)); + +/* Debug Space */ +struct dbg { + __be32 bpdcr; /* Breakpoint debug command register */ + __be32 bpdsr; /* Breakpoint debug status register */ + __be32 bpdmr; /* Breakpoint debug mask register */ + __be32 bprmrr0; /* Breakpoint request mode risc register 0 */ + __be32 bprmrr1; /* Breakpoint request mode risc register 1 */ + u8 res0[0x8]; + __be32 bprmtr0; /* Breakpoint request mode trb register 0 */ + __be32 bprmtr1; /* Breakpoint request mode trb register 1 */ + u8 res1[0x8]; + __be32 bprmir; /* Breakpoint request mode immediate register */ + __be32 bprmsr; /* Breakpoint request mode serial register */ + __be32 bpemr; /* Breakpoint exit mode register */ + u8 res2[0x48]; +} __attribute__ ((packed)); + +/* RISC Special Registers (Trap and Breakpoint) */ +struct rsp { + u8 fixme[0x100]; +} __attribute__ ((packed)); + +struct qe_immap { + struct qe_iram iram; /* I-RAM */ + struct qe_ic_regs ic; /* Interrupt Controller */ + struct cp_qe cp; /* Communications Processor */ + struct qe_mux qmx; /* QE Multiplexer */ + struct qe_timers qet; /* QE Timers */ + struct spi spi[0x2]; /* spi */ + struct mcc mcc; /* mcc */ + struct qe_brg brg; /* brg */ + struct usb_ctlr usb; /* USB */ + struct si1 si1; /* SI */ + u8 res11[0x800]; + struct sir sir; /* SI Routing Tables */ + struct ucc ucc1; /* ucc1 */ + struct ucc ucc3; /* ucc3 */ + struct ucc ucc5; /* ucc5 */ + struct ucc ucc7; /* ucc7 */ + u8 res12[0x600]; + struct upc upc1; /* MultiPHY UTOPIA POS Ctrlr 1*/ + struct ucc ucc2; /* ucc2 */ + struct ucc ucc4; /* ucc4 */ + struct ucc ucc6; /* ucc6 */ + struct ucc ucc8; /* ucc8 */ + u8 res13[0x600]; + struct upc upc2; /* MultiPHY UTOPIA POS Ctrlr 2*/ + struct sdma sdma; /* SDMA */ + struct dbg dbg; /* Debug Space */ + struct rsp rsp[0x2]; /* RISC Special Registers + (Trap and Breakpoint) */ + u8 res14[0x300]; + u8 res15[0x3A00]; + u8 res16[0x8000]; /* 0x108000 - 0x110000 */ + u8 muram[0xC000]; /* 0x110000 - 0x11C000 + Multi-user RAM */ + u8 res17[0x24000]; /* 0x11C000 - 0x140000 */ + u8 res18[0xC0000]; /* 0x140000 - 0x200000 */ +} __attribute__ ((packed)); + +extern struct qe_immap *qe_immr; +extern phys_addr_t get_qe_base(void); + +static inline unsigned long immrbar_virt_to_phys(volatile void * address) +{ + if ( ((u32)address >= (u32)qe_immr) && + ((u32)address < ((u32)qe_immr + QE_IMMAP_SIZE)) ) + return (unsigned long)(address - (u32)qe_immr + + (u32)get_qe_base()); + return (unsigned long)virt_to_phys(address); +} + +#endif /* __KERNEL__ */ +#endif /* _ASM_POWERPC_IMMAP_QE_H */ diff --git a/include/asm-powerpc/qe.h b/include/asm-powerpc/qe.h new file mode 100644 index 000000000000..a62168ec535f --- /dev/null +++ b/include/asm-powerpc/qe.h @@ -0,0 +1,457 @@ +/* + * Copyright (C) 2006 Freescale Semicondutor, Inc. All rights reserved. + * + * Authors: Shlomi Gridish <gridish@freescale.com> + * Li Yang <leoli@freescale.com> + * + * Description: + * QUICC Engine (QE) external definitions and structure. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#ifndef _ASM_POWERPC_QE_H +#define _ASM_POWERPC_QE_H +#ifdef __KERNEL__ + +#include <asm/immap_qe.h> + +#define QE_NUM_OF_SNUM 28 +#define QE_NUM_OF_BRGS 16 +#define QE_NUM_OF_PORTS 1024 + +/* Memory partitions +*/ +#define MEM_PART_SYSTEM 0 +#define MEM_PART_SECONDARY 1 +#define MEM_PART_MURAM 2 + +/* Export QE common operations */ +extern void qe_reset(void); +extern int par_io_init(struct device_node *np); +extern int par_io_of_config(struct device_node *np); + +/* QE internal API */ +int qe_issue_cmd(u32 cmd, u32 device, u8 mcn_protocol, u32 cmd_input); +void qe_setbrg(u32 brg, u32 rate); +int qe_get_snum(void); +void qe_put_snum(u8 snum); +u32 qe_muram_alloc(u32 size, u32 align); +int qe_muram_free(u32 offset); +u32 qe_muram_alloc_fixed(u32 offset, u32 size); +void qe_muram_dump(void); +void *qe_muram_addr(u32 offset); + +/* Buffer descriptors */ +struct qe_bd { + u16 status; + u16 length; + u32 buf; +} __attribute__ ((packed)); + +#define BD_STATUS_MASK 0xffff0000 +#define BD_LENGTH_MASK 0x0000ffff + +/* Alignment */ +#define QE_INTR_TABLE_ALIGN 16 /* ??? */ +#define QE_ALIGNMENT_OF_BD 8 +#define QE_ALIGNMENT_OF_PRAM 64 + +/* RISC allocation */ +enum qe_risc_allocation { + QE_RISC_ALLOCATION_RISC1 = 1, /* RISC 1 */ + QE_RISC_ALLOCATION_RISC2 = 2, /* RISC 2 */ + QE_RISC_ALLOCATION_RISC1_AND_RISC2 = 3 /* Dynamically choose + RISC 1 or RISC 2 */ +}; + +/* QE extended filtering Table Lookup Key Size */ +enum qe_fltr_tbl_lookup_key_size { + QE_FLTR_TABLE_LOOKUP_KEY_SIZE_8_BYTES + = 0x3f, /* LookupKey parsed by the Generate LookupKey + CMD is truncated to 8 bytes */ + QE_FLTR_TABLE_LOOKUP_KEY_SIZE_16_BYTES + = 0x5f, /* LookupKey parsed by the Generate LookupKey + CMD is truncated to 16 bytes */ +}; + +/* QE FLTR extended filtering Largest External Table Lookup Key Size */ +enum qe_fltr_largest_external_tbl_lookup_key_size { + QE_FLTR_LARGEST_EXTERNAL_TABLE_LOOKUP_KEY_SIZE_NONE + = 0x0,/* not used */ + QE_FLTR_LARGEST_EXTERNAL_TABLE_LOOKUP_KEY_SIZE_8_BYTES + = QE_FLTR_TABLE_LOOKUP_KEY_SIZE_8_BYTES, /* 8 bytes */ + QE_FLTR_LARGEST_EXTERNAL_TABLE_LOOKUP_KEY_SIZE_16_BYTES + = QE_FLTR_TABLE_LOOKUP_KEY_SIZE_16_BYTES, /* 16 bytes */ +}; + +/* structure representing QE parameter RAM */ +struct qe_timer_tables { + u16 tm_base; /* QE timer table base adr */ + u16 tm_ptr; /* QE timer table pointer */ + u16 r_tmr; /* QE timer mode register */ + u16 r_tmv; /* QE timer valid register */ + u32 tm_cmd; /* QE timer cmd register */ + u32 tm_cnt; /* QE timer internal cnt */ +} __attribute__ ((packed)); + +#define QE_FLTR_TAD_SIZE 8 + +/* QE extended filtering Termination Action Descriptor (TAD) */ +struct qe_fltr_tad { + u8 serialized[QE_FLTR_TAD_SIZE]; +} __attribute__ ((packed)); + +/* Communication Direction */ +enum comm_dir { + COMM_DIR_NONE = 0, + COMM_DIR_RX = 1, + COMM_DIR_TX = 2, + COMM_DIR_RX_AND_TX = 3 +}; + +/* Clocks and BRGs */ +enum qe_clock { + QE_CLK_NONE = 0, + QE_BRG1, /* Baud Rate Generator 1 */ + QE_BRG2, /* Baud Rate Generator 2 */ + QE_BRG3, /* Baud Rate Generator 3 */ + QE_BRG4, /* Baud Rate Generator 4 */ + QE_BRG5, /* Baud Rate Generator 5 */ + QE_BRG6, /* Baud Rate Generator 6 */ + QE_BRG7, /* Baud Rate Generator 7 */ + QE_BRG8, /* Baud Rate Generator 8 */ + QE_BRG9, /* Baud Rate Generator 9 */ + QE_BRG10, /* Baud Rate Generator 10 */ + QE_BRG11, /* Baud Rate Generator 11 */ + QE_BRG12, /* Baud Rate Generator 12 */ + QE_BRG13, /* Baud Rate Generator 13 */ + QE_BRG14, /* Baud Rate Generator 14 */ + QE_BRG15, /* Baud Rate Generator 15 */ + QE_BRG16, /* Baud Rate Generator 16 */ + QE_CLK1, /* Clock 1 */ + QE_CLK2, /* Clock 2 */ + QE_CLK3, /* Clock 3 */ + QE_CLK4, /* Clock 4 */ + QE_CLK5, /* Clock 5 */ + QE_CLK6, /* Clock 6 */ + QE_CLK7, /* Clock 7 */ + QE_CLK8, /* Clock 8 */ + QE_CLK9, /* Clock 9 */ + QE_CLK10, /* Clock 10 */ + QE_CLK11, /* Clock 11 */ + QE_CLK12, /* Clock 12 */ + QE_CLK13, /* Clock 13 */ + QE_CLK14, /* Clock 14 */ + QE_CLK15, /* Clock 15 */ + QE_CLK16, /* Clock 16 */ + QE_CLK17, /* Clock 17 */ + QE_CLK18, /* Clock 18 */ + QE_CLK19, /* Clock 19 */ + QE_CLK20, /* Clock 20 */ + QE_CLK21, /* Clock 21 */ + QE_CLK22, /* Clock 22 */ + QE_CLK23, /* Clock 23 */ + QE_CLK24, /* Clock 24 */ + QE_CLK_DUMMY, +}; + +/* QE CMXUCR Registers. + * There are two UCCs represented in each of the four CMXUCR registers. + * These values are for the UCC in the LSBs + */ +#define QE_CMXUCR_MII_ENET_MNG 0x00007000 +#define QE_CMXUCR_MII_ENET_MNG_SHIFT 12 +#define QE_CMXUCR_GRANT 0x00008000 +#define QE_CMXUCR_TSA 0x00004000 +#define QE_CMXUCR_BKPT 0x00000100 +#define QE_CMXUCR_TX_CLK_SRC_MASK 0x0000000F + +/* QE CMXGCR Registers. +*/ +#define QE_CMXGCR_MII_ENET_MNG 0x00007000 +#define QE_CMXGCR_MII_ENET_MNG_SHIFT 12 +#define QE_CMXGCR_USBCS 0x0000000f + +/* QE CECR Commands. +*/ +#define QE_CR_FLG 0x00010000 +#define QE_RESET 0x80000000 +#define QE_INIT_TX_RX 0x00000000 +#define QE_INIT_RX 0x00000001 +#define QE_INIT_TX 0x00000002 +#define QE_ENTER_HUNT_MODE 0x00000003 +#define QE_STOP_TX 0x00000004 +#define QE_GRACEFUL_STOP_TX 0x00000005 +#define QE_RESTART_TX 0x00000006 +#define QE_CLOSE_RX_BD 0x00000007 +#define QE_SWITCH_COMMAND 0x00000007 +#define QE_SET_GROUP_ADDRESS 0x00000008 +#define QE_START_IDMA 0x00000009 +#define QE_MCC_STOP_RX 0x00000009 +#define QE_ATM_TRANSMIT 0x0000000a +#define QE_HPAC_CLEAR_ALL 0x0000000b +#define QE_GRACEFUL_STOP_RX 0x0000001a +#define QE_RESTART_RX 0x0000001b +#define QE_HPAC_SET_PRIORITY 0x0000010b +#define QE_HPAC_STOP_TX 0x0000020b +#define QE_HPAC_STOP_RX 0x0000030b +#define QE_HPAC_GRACEFUL_STOP_TX 0x0000040b +#define QE_HPAC_GRACEFUL_STOP_RX 0x0000050b +#define QE_HPAC_START_TX 0x0000060b +#define QE_HPAC_START_RX 0x0000070b +#define QE_USB_STOP_TX 0x0000000a +#define QE_USB_RESTART_TX 0x0000000b +#define QE_QMC_STOP_TX 0x0000000c +#define QE_QMC_STOP_RX 0x0000000d +#define QE_SS7_SU_FIL_RESET 0x0000000e +/* jonathbr added from here down for 83xx */ +#define QE_RESET_BCS 0x0000000a +#define QE_MCC_INIT_TX_RX_16 0x00000003 +#define QE_MCC_STOP_TX 0x00000004 +#define QE_MCC_INIT_TX_1 0x00000005 +#define QE_MCC_INIT_RX_1 0x00000006 +#define QE_MCC_RESET 0x00000007 +#define QE_SET_TIMER 0x00000008 +#define QE_RANDOM_NUMBER 0x0000000c +#define QE_ATM_MULTI_THREAD_INIT 0x00000011 +#define QE_ASSIGN_PAGE 0x00000012 +#define QE_ADD_REMOVE_HASH_ENTRY 0x00000013 +#define QE_START_FLOW_CONTROL 0x00000014 +#define QE_STOP_FLOW_CONTROL 0x00000015 +#define QE_ASSIGN_PAGE_TO_DEVICE 0x00000016 + +#define QE_ASSIGN_RISC 0x00000010 +#define QE_CR_MCN_NORMAL_SHIFT 6 +#define QE_CR_MCN_USB_SHIFT 4 +#define QE_CR_MCN_RISC_ASSIGN_SHIFT 8 +#define QE_CR_SNUM_SHIFT 17 + +/* QE CECR Sub Block - sub block of QE command. +*/ +#define QE_CR_SUBBLOCK_INVALID 0x00000000 +#define QE_CR_SUBBLOCK_USB 0x03200000 +#define QE_CR_SUBBLOCK_UCCFAST1 0x02000000 +#define QE_CR_SUBBLOCK_UCCFAST2 0x02200000 +#define QE_CR_SUBBLOCK_UCCFAST3 0x02400000 +#define QE_CR_SUBBLOCK_UCCFAST4 0x02600000 +#define QE_CR_SUBBLOCK_UCCFAST5 0x02800000 +#define QE_CR_SUBBLOCK_UCCFAST6 0x02a00000 +#define QE_CR_SUBBLOCK_UCCFAST7 0x02c00000 +#define QE_CR_SUBBLOCK_UCCFAST8 0x02e00000 +#define QE_CR_SUBBLOCK_UCCSLOW1 0x00000000 +#define QE_CR_SUBBLOCK_UCCSLOW2 0x00200000 +#define QE_CR_SUBBLOCK_UCCSLOW3 0x00400000 +#define QE_CR_SUBBLOCK_UCCSLOW4 0x00600000 +#define QE_CR_SUBBLOCK_UCCSLOW5 0x00800000 +#define QE_CR_SUBBLOCK_UCCSLOW6 0x00a00000 +#define QE_CR_SUBBLOCK_UCCSLOW7 0x00c00000 +#define QE_CR_SUBBLOCK_UCCSLOW8 0x00e00000 +#define QE_CR_SUBBLOCK_MCC1 0x03800000 +#define QE_CR_SUBBLOCK_MCC2 0x03a00000 +#define QE_CR_SUBBLOCK_MCC3 0x03000000 +#define QE_CR_SUBBLOCK_IDMA1 0x02800000 +#define QE_CR_SUBBLOCK_IDMA2 0x02a00000 +#define QE_CR_SUBBLOCK_IDMA3 0x02c00000 +#define QE_CR_SUBBLOCK_IDMA4 0x02e00000 +#define QE_CR_SUBBLOCK_HPAC 0x01e00000 +#define QE_CR_SUBBLOCK_SPI1 0x01400000 +#define QE_CR_SUBBLOCK_SPI2 0x01600000 +#define QE_CR_SUBBLOCK_RAND 0x01c00000 +#define QE_CR_SUBBLOCK_TIMER 0x01e00000 +#define QE_CR_SUBBLOCK_GENERAL 0x03c00000 + +/* QE CECR Protocol - For non-MCC, specifies mode for QE CECR command */ +#define QE_CR_PROTOCOL_UNSPECIFIED 0x00 /* For all other protocols */ +#define QE_CR_PROTOCOL_HDLC_TRANSPARENT 0x00 +#define QE_CR_PROTOCOL_ATM_POS 0x0A +#define QE_CR_PROTOCOL_ETHERNET 0x0C +#define QE_CR_PROTOCOL_L2_SWITCH 0x0D + +/* BMR byte order */ +#define QE_BMR_BYTE_ORDER_BO_PPC 0x08 /* powerpc little endian */ +#define QE_BMR_BYTE_ORDER_BO_MOT 0x10 /* motorola big endian */ +#define QE_BMR_BYTE_ORDER_BO_MAX 0x18 + +/* BRG configuration register */ +#define QE_BRGC_ENABLE 0x00010000 +#define QE_BRGC_DIVISOR_SHIFT 1 +#define QE_BRGC_DIVISOR_MAX 0xFFF +#define QE_BRGC_DIV16 1 + +/* QE Timers registers */ +#define QE_GTCFR1_PCAS 0x80 +#define QE_GTCFR1_STP2 0x20 +#define QE_GTCFR1_RST2 0x10 +#define QE_GTCFR1_GM2 0x08 +#define QE_GTCFR1_GM1 0x04 +#define QE_GTCFR1_STP1 0x02 +#define QE_GTCFR1_RST1 0x01 + +/* SDMA registers */ +#define QE_SDSR_BER1 0x02000000 +#define QE_SDSR_BER2 0x01000000 + +#define QE_SDMR_GLB_1_MSK 0x80000000 +#define QE_SDMR_ADR_SEL 0x20000000 +#define QE_SDMR_BER1_MSK 0x02000000 +#define QE_SDMR_BER2_MSK 0x01000000 +#define QE_SDMR_EB1_MSK 0x00800000 +#define QE_SDMR_ER1_MSK 0x00080000 +#define QE_SDMR_ER2_MSK 0x00040000 +#define QE_SDMR_CEN_MASK 0x0000E000 +#define QE_SDMR_SBER_1 0x00000200 +#define QE_SDMR_SBER_2 0x00000200 +#define QE_SDMR_EB1_PR_MASK 0x000000C0 +#define QE_SDMR_ER1_PR 0x00000008 + +#define QE_SDMR_CEN_SHIFT 13 +#define QE_SDMR_EB1_PR_SHIFT 6 + +#define QE_SDTM_MSNUM_SHIFT 24 + +#define QE_SDEBCR_BA_MASK 0x01FFFFFF + +/* UPC */ +#define UPGCR_PROTOCOL 0x80000000 /* protocol ul2 or pl2 */ +#define UPGCR_TMS 0x40000000 /* Transmit master/slave mode */ +#define UPGCR_RMS 0x20000000 /* Receive master/slave mode */ +#define UPGCR_ADDR 0x10000000 /* Master MPHY Addr multiplexing */ +#define UPGCR_DIAG 0x01000000 /* Diagnostic mode */ + +/* UCC */ +#define UCC_GUEMR_MODE_MASK_RX 0x02 +#define UCC_GUEMR_MODE_MASK_TX 0x01 +#define UCC_GUEMR_MODE_FAST_RX 0x02 +#define UCC_GUEMR_MODE_FAST_TX 0x01 +#define UCC_GUEMR_MODE_SLOW_RX 0x00 +#define UCC_GUEMR_MODE_SLOW_TX 0x00 +#define UCC_GUEMR_SET_RESERVED3 0x10 /* Bit 3 in the guemr is reserved but + must be set 1 */ + +/* structure representing UCC SLOW parameter RAM */ +struct ucc_slow_pram { + u16 rbase; /* RX BD base address */ + u16 tbase; /* TX BD base address */ + u8 rfcr; /* Rx function code */ + u8 tfcr; /* Tx function code */ + u16 mrblr; /* Rx buffer length */ + u32 rstate; /* Rx internal state */ + u32 rptr; /* Rx internal data pointer */ + u16 rbptr; /* rb BD Pointer */ + u16 rcount; /* Rx internal byte count */ + u32 rtemp; /* Rx temp */ + u32 tstate; /* Tx internal state */ + u32 tptr; /* Tx internal data pointer */ + u16 tbptr; /* Tx BD pointer */ + u16 tcount; /* Tx byte count */ + u32 ttemp; /* Tx temp */ + u32 rcrc; /* temp receive CRC */ + u32 tcrc; /* temp transmit CRC */ +} __attribute__ ((packed)); + +/* General UCC SLOW Mode Register (GUMRH & GUMRL) */ +#define UCC_SLOW_GUMR_H_CRC16 0x00004000 +#define UCC_SLOW_GUMR_H_CRC16CCITT 0x00000000 +#define UCC_SLOW_GUMR_H_CRC32CCITT 0x00008000 +#define UCC_SLOW_GUMR_H_REVD 0x00002000 +#define UCC_SLOW_GUMR_H_TRX 0x00001000 +#define UCC_SLOW_GUMR_H_TTX 0x00000800 +#define UCC_SLOW_GUMR_H_CDP 0x00000400 +#define UCC_SLOW_GUMR_H_CTSP 0x00000200 +#define UCC_SLOW_GUMR_H_CDS 0x00000100 +#define UCC_SLOW_GUMR_H_CTSS 0x00000080 +#define UCC_SLOW_GUMR_H_TFL 0x00000040 +#define UCC_SLOW_GUMR_H_RFW 0x00000020 +#define UCC_SLOW_GUMR_H_TXSY 0x00000010 +#define UCC_SLOW_GUMR_H_4SYNC 0x00000004 +#define UCC_SLOW_GUMR_H_8SYNC 0x00000008 +#define UCC_SLOW_GUMR_H_16SYNC 0x0000000c +#define UCC_SLOW_GUMR_H_RTSM 0x00000002 +#define UCC_SLOW_GUMR_H_RSYN 0x00000001 + +#define UCC_SLOW_GUMR_L_TCI 0x10000000 +#define UCC_SLOW_GUMR_L_RINV 0x02000000 +#define UCC_SLOW_GUMR_L_TINV 0x01000000 +#define UCC_SLOW_GUMR_L_TEND 0x00020000 +#define UCC_SLOW_GUMR_L_ENR 0x00000020 +#define UCC_SLOW_GUMR_L_ENT 0x00000010 + +/* General UCC FAST Mode Register */ +#define UCC_FAST_GUMR_TCI 0x20000000 +#define UCC_FAST_GUMR_TRX 0x10000000 +#define UCC_FAST_GUMR_TTX 0x08000000 +#define UCC_FAST_GUMR_CDP 0x04000000 +#define UCC_FAST_GUMR_CTSP 0x02000000 +#define UCC_FAST_GUMR_CDS 0x01000000 +#define UCC_FAST_GUMR_CTSS 0x00800000 +#define UCC_FAST_GUMR_TXSY 0x00020000 +#define UCC_FAST_GUMR_RSYN 0x00010000 +#define UCC_FAST_GUMR_RTSM 0x00002000 +#define UCC_FAST_GUMR_REVD 0x00000400 +#define UCC_FAST_GUMR_ENR 0x00000020 +#define UCC_FAST_GUMR_ENT 0x00000010 + +/* Slow UCC Event Register (UCCE) */ +#define UCC_SLOW_UCCE_GLR 0x1000 +#define UCC_SLOW_UCCE_GLT 0x0800 +#define UCC_SLOW_UCCE_DCC 0x0400 +#define UCC_SLOW_UCCE_FLG 0x0200 +#define UCC_SLOW_UCCE_AB 0x0200 +#define UCC_SLOW_UCCE_IDLE 0x0100 +#define UCC_SLOW_UCCE_GRA 0x0080 +#define UCC_SLOW_UCCE_TXE 0x0010 +#define UCC_SLOW_UCCE_RXF 0x0008 +#define UCC_SLOW_UCCE_CCR 0x0008 +#define UCC_SLOW_UCCE_RCH 0x0008 +#define UCC_SLOW_UCCE_BSY 0x0004 +#define UCC_SLOW_UCCE_TXB 0x0002 +#define UCC_SLOW_UCCE_TX 0x0002 +#define UCC_SLOW_UCCE_RX 0x0001 +#define UCC_SLOW_UCCE_GOV 0x0001 +#define UCC_SLOW_UCCE_GUN 0x0002 +#define UCC_SLOW_UCCE_GINT 0x0004 +#define UCC_SLOW_UCCE_IQOV 0x0008 + +#define UCC_SLOW_UCCE_HDLC_SET (UCC_SLOW_UCCE_TXE | UCC_SLOW_UCCE_BSY | \ + UCC_SLOW_UCCE_GRA | UCC_SLOW_UCCE_TXB | UCC_SLOW_UCCE_RXF | \ + UCC_SLOW_UCCE_DCC | UCC_SLOW_UCCE_GLT | UCC_SLOW_UCCE_GLR) +#define UCC_SLOW_UCCE_ENET_SET (UCC_SLOW_UCCE_TXE | UCC_SLOW_UCCE_BSY | \ + UCC_SLOW_UCCE_GRA | UCC_SLOW_UCCE_TXB | UCC_SLOW_UCCE_RXF) +#define UCC_SLOW_UCCE_TRANS_SET (UCC_SLOW_UCCE_TXE | UCC_SLOW_UCCE_BSY | \ + UCC_SLOW_UCCE_GRA | UCC_SLOW_UCCE_TX | UCC_SLOW_UCCE_RX | \ + UCC_SLOW_UCCE_DCC | UCC_SLOW_UCCE_GLT | UCC_SLOW_UCCE_GLR) +#define UCC_SLOW_UCCE_UART_SET (UCC_SLOW_UCCE_BSY | UCC_SLOW_UCCE_GRA | \ + UCC_SLOW_UCCE_TXB | UCC_SLOW_UCCE_TX | UCC_SLOW_UCCE_RX | \ + UCC_SLOW_UCCE_GLT | UCC_SLOW_UCCE_GLR) +#define UCC_SLOW_UCCE_QMC_SET (UCC_SLOW_UCCE_IQOV | UCC_SLOW_UCCE_GINT | \ + UCC_SLOW_UCCE_GUN | UCC_SLOW_UCCE_GOV) + +#define UCC_SLOW_UCCE_OTHER (UCC_SLOW_UCCE_TXE | UCC_SLOW_UCCE_BSY | \ + UCC_SLOW_UCCE_GRA | UCC_SLOW_UCCE_DCC | UCC_SLOW_UCCE_GLT | \ + UCC_SLOW_UCCE_GLR) + +#define UCC_SLOW_INTR_TX UCC_SLOW_UCCE_TXB +#define UCC_SLOW_INTR_RX (UCC_SLOW_UCCE_RXF | UCC_SLOW_UCCE_RX) +#define UCC_SLOW_INTR (UCC_SLOW_INTR_TX | UCC_SLOW_INTR_RX) + +/* UCC Transmit On Demand Register (UTODR) */ +#define UCC_SLOW_TOD 0x8000 +#define UCC_FAST_TOD 0x8000 + +/* Function code masks */ +#define FC_GBL 0x20 +#define FC_DTB_LCL 0x02 +#define UCC_FAST_FUNCTION_CODE_GBL 0x20 +#define UCC_FAST_FUNCTION_CODE_DTB_LCL 0x02 +#define UCC_FAST_FUNCTION_CODE_BDB_LCL 0x01 + +static inline long IS_MURAM_ERR(const u32 offset) +{ + return offset > (u32) - 1000L; +} + +#endif /* __KERNEL__ */ +#endif /* _ASM_POWERPC_QE_H */ diff --git a/include/asm-powerpc/qe_ic.h b/include/asm-powerpc/qe_ic.h new file mode 100644 index 000000000000..e386fb7e44b0 --- /dev/null +++ b/include/asm-powerpc/qe_ic.h @@ -0,0 +1,64 @@ +/* + * include/asm-powerpc/qe_ic.h + * + * Copyright (C) 2006 Freescale Semicondutor, Inc. All rights reserved. + * + * Authors: Shlomi Gridish <gridish@freescale.com> + * Li Yang <leoli@freescale.com> + * + * Description: + * QE IC external definitions and structure. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#ifndef _ASM_POWERPC_QE_IC_H +#define _ASM_POWERPC_QE_IC_H + +#include <linux/irq.h> + +#define NUM_OF_QE_IC_GROUPS 6 + +/* Flags when we init the QE IC */ +#define QE_IC_SPREADMODE_GRP_W 0x00000001 +#define QE_IC_SPREADMODE_GRP_X 0x00000002 +#define QE_IC_SPREADMODE_GRP_Y 0x00000004 +#define QE_IC_SPREADMODE_GRP_Z 0x00000008 +#define QE_IC_SPREADMODE_GRP_RISCA 0x00000010 +#define QE_IC_SPREADMODE_GRP_RISCB 0x00000020 + +#define QE_IC_LOW_SIGNAL 0x00000100 +#define QE_IC_HIGH_SIGNAL 0x00000200 + +#define QE_IC_GRP_W_PRI0_DEST_SIGNAL_HIGH 0x00001000 +#define QE_IC_GRP_W_PRI1_DEST_SIGNAL_HIGH 0x00002000 +#define QE_IC_GRP_X_PRI0_DEST_SIGNAL_HIGH 0x00004000 +#define QE_IC_GRP_X_PRI1_DEST_SIGNAL_HIGH 0x00008000 +#define QE_IC_GRP_Y_PRI0_DEST_SIGNAL_HIGH 0x00010000 +#define QE_IC_GRP_Y_PRI1_DEST_SIGNAL_HIGH 0x00020000 +#define QE_IC_GRP_Z_PRI0_DEST_SIGNAL_HIGH 0x00040000 +#define QE_IC_GRP_Z_PRI1_DEST_SIGNAL_HIGH 0x00080000 +#define QE_IC_GRP_RISCA_PRI0_DEST_SIGNAL_HIGH 0x00100000 +#define QE_IC_GRP_RISCA_PRI1_DEST_SIGNAL_HIGH 0x00200000 +#define QE_IC_GRP_RISCB_PRI0_DEST_SIGNAL_HIGH 0x00400000 +#define QE_IC_GRP_RISCB_PRI1_DEST_SIGNAL_HIGH 0x00800000 +#define QE_IC_GRP_W_DEST_SIGNAL_SHIFT (12) + +/* QE interrupt sources groups */ +enum qe_ic_grp_id { + QE_IC_GRP_W = 0, /* QE interrupt controller group W */ + QE_IC_GRP_X, /* QE interrupt controller group X */ + QE_IC_GRP_Y, /* QE interrupt controller group Y */ + QE_IC_GRP_Z, /* QE interrupt controller group Z */ + QE_IC_GRP_RISCA, /* QE interrupt controller RISC group A */ + QE_IC_GRP_RISCB /* QE interrupt controller RISC group B */ +}; + +void qe_ic_init(struct device_node *node, unsigned int flags); +void qe_ic_set_highest_priority(unsigned int virq, int high); +int qe_ic_set_priority(unsigned int virq, unsigned int priority); +int qe_ic_set_high_priority(unsigned int virq, unsigned int priority, int high); + +#endif /* _ASM_POWERPC_QE_IC_H */ diff --git a/include/asm-powerpc/system.h b/include/asm-powerpc/system.h index 4b41deaa8d8d..43627596003b 100644 --- a/include/asm-powerpc/system.h +++ b/include/asm-powerpc/system.h @@ -91,10 +91,6 @@ DEBUGGER_BOILERPLATE(debugger_iabr_match) DEBUGGER_BOILERPLATE(debugger_dabr_match) DEBUGGER_BOILERPLATE(debugger_fault_handler) -#ifdef CONFIG_XMON -extern void xmon_init(int enable); -#endif - #else static inline int debugger(struct pt_regs *regs) { return 0; } static inline int debugger_ipi(struct pt_regs *regs) { return 0; } diff --git a/include/asm-powerpc/ucc.h b/include/asm-powerpc/ucc.h new file mode 100644 index 000000000000..afe3076bdc03 --- /dev/null +++ b/include/asm-powerpc/ucc.h @@ -0,0 +1,84 @@ +/* + * Copyright (C) 2006 Freescale Semicondutor, Inc. All rights reserved. + * + * Authors: Shlomi Gridish <gridish@freescale.com> + * Li Yang <leoli@freescale.com> + * + * Description: + * Internal header file for UCC unit routines. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#ifndef __UCC_H__ +#define __UCC_H__ + +#include <asm/immap_qe.h> +#include <asm/qe.h> + +#define STATISTICS + +#define UCC_MAX_NUM 8 + +/* Slow or fast type for UCCs. +*/ +enum ucc_speed_type { + UCC_SPEED_TYPE_FAST, UCC_SPEED_TYPE_SLOW +}; + +/* Initial UCCs Parameter RAM address relative to: MEM_MAP_BASE (IMMR). +*/ +enum ucc_pram_initial_offset { + UCC_PRAM_OFFSET_UCC1 = 0x8400, + UCC_PRAM_OFFSET_UCC2 = 0x8500, + UCC_PRAM_OFFSET_UCC3 = 0x8600, + UCC_PRAM_OFFSET_UCC4 = 0x9000, + UCC_PRAM_OFFSET_UCC5 = 0x8000, + UCC_PRAM_OFFSET_UCC6 = 0x8100, + UCC_PRAM_OFFSET_UCC7 = 0x8200, + UCC_PRAM_OFFSET_UCC8 = 0x8300 +}; + +/* ucc_set_type + * Sets UCC to slow or fast mode. + * + * ucc_num - (In) number of UCC (0-7). + * regs - (In) pointer to registers base for the UCC. + * speed - (In) slow or fast mode for UCC. + */ +int ucc_set_type(int ucc_num, struct ucc_common *regs, + enum ucc_speed_type speed); + +/* ucc_init_guemr + * Init the Guemr register. + * + * regs - (In) pointer to registers base for the UCC. + */ +int ucc_init_guemr(struct ucc_common *regs); + +int ucc_set_qe_mux_mii_mng(int ucc_num); + +int ucc_set_qe_mux_rxtx(int ucc_num, enum qe_clock clock, enum comm_dir mode); + +int ucc_mux_set_grant_tsa_bkpt(int ucc_num, int set, u32 mask); + +/* QE MUX clock routing for UCC +*/ +static inline int ucc_set_qe_mux_grant(int ucc_num, int set) +{ + return ucc_mux_set_grant_tsa_bkpt(ucc_num, set, QE_CMXUCR_GRANT); +} + +static inline int ucc_set_qe_mux_tsa(int ucc_num, int set) +{ + return ucc_mux_set_grant_tsa_bkpt(ucc_num, set, QE_CMXUCR_TSA); +} + +static inline int ucc_set_qe_mux_bkpt(int ucc_num, int set) +{ + return ucc_mux_set_grant_tsa_bkpt(ucc_num, set, QE_CMXUCR_BKPT); +} + +#endif /* __UCC_H__ */ diff --git a/include/asm-powerpc/ucc_fast.h b/include/asm-powerpc/ucc_fast.h new file mode 100644 index 000000000000..39d1c90fd2ca --- /dev/null +++ b/include/asm-powerpc/ucc_fast.h @@ -0,0 +1,243 @@ +/* + * include/asm-powerpc/ucc_fast.h + * + * Internal header file for UCC FAST unit routines. + * + * Copyright (C) 2006 Freescale Semicondutor, Inc. All rights reserved. + * + * Authors: Shlomi Gridish <gridish@freescale.com> + * Li Yang <leoli@freescale.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#ifndef __UCC_FAST_H__ +#define __UCC_FAST_H__ + +#include <linux/kernel.h> + +#include <asm/immap_qe.h> +#include <asm/qe.h> + +#include "ucc.h" + +/* Receive BD's status */ +#define R_E 0x80000000 /* buffer empty */ +#define R_W 0x20000000 /* wrap bit */ +#define R_I 0x10000000 /* interrupt on reception */ +#define R_L 0x08000000 /* last */ +#define R_F 0x04000000 /* first */ + +/* transmit BD's status */ +#define T_R 0x80000000 /* ready bit */ +#define T_W 0x20000000 /* wrap bit */ +#define T_I 0x10000000 /* interrupt on completion */ +#define T_L 0x08000000 /* last */ + +/* Rx Data buffer must be 4 bytes aligned in most cases */ +#define UCC_FAST_RX_ALIGN 4 +#define UCC_FAST_MRBLR_ALIGNMENT 4 +#define UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT 8 + +/* Sizes */ +#define UCC_FAST_URFS_MIN_VAL 0x88 +#define UCC_FAST_RECEIVE_VIRTUAL_FIFO_SIZE_FUDGE_FACTOR 8 + +/* ucc_fast_channel_protocol_mode - UCC FAST mode */ +enum ucc_fast_channel_protocol_mode { + UCC_FAST_PROTOCOL_MODE_HDLC = 0x00000000, + UCC_FAST_PROTOCOL_MODE_RESERVED01 = 0x00000001, + UCC_FAST_PROTOCOL_MODE_RESERVED_QMC = 0x00000002, + UCC_FAST_PROTOCOL_MODE_RESERVED02 = 0x00000003, + UCC_FAST_PROTOCOL_MODE_RESERVED_UART = 0x00000004, + UCC_FAST_PROTOCOL_MODE_RESERVED03 = 0x00000005, + UCC_FAST_PROTOCOL_MODE_RESERVED_EX_MAC_1 = 0x00000006, + UCC_FAST_PROTOCOL_MODE_RESERVED_EX_MAC_2 = 0x00000007, + UCC_FAST_PROTOCOL_MODE_RESERVED_BISYNC = 0x00000008, + UCC_FAST_PROTOCOL_MODE_RESERVED04 = 0x00000009, + UCC_FAST_PROTOCOL_MODE_ATM = 0x0000000A, + UCC_FAST_PROTOCOL_MODE_RESERVED05 = 0x0000000B, + UCC_FAST_PROTOCOL_MODE_ETHERNET = 0x0000000C, + UCC_FAST_PROTOCOL_MODE_RESERVED06 = 0x0000000D, + UCC_FAST_PROTOCOL_MODE_POS = 0x0000000E, + UCC_FAST_PROTOCOL_MODE_RESERVED07 = 0x0000000F +}; + +/* ucc_fast_transparent_txrx - UCC Fast Transparent TX & RX */ +enum ucc_fast_transparent_txrx { + UCC_FAST_GUMR_TRANSPARENT_TTX_TRX_NORMAL = 0x00000000, + UCC_FAST_GUMR_TRANSPARENT_TTX_TRX_TRANSPARENT = 0x18000000 +}; + +/* UCC fast diagnostic mode */ +enum ucc_fast_diag_mode { + UCC_FAST_DIAGNOSTIC_NORMAL = 0x0, + UCC_FAST_DIAGNOSTIC_LOCAL_LOOP_BACK = 0x40000000, + UCC_FAST_DIAGNOSTIC_AUTO_ECHO = 0x80000000, + UCC_FAST_DIAGNOSTIC_LOOP_BACK_AND_ECHO = 0xC0000000 +}; + +/* UCC fast Sync length (transparent mode only) */ +enum ucc_fast_sync_len { + UCC_FAST_SYNC_LEN_NOT_USED = 0x0, + UCC_FAST_SYNC_LEN_AUTOMATIC = 0x00004000, + UCC_FAST_SYNC_LEN_8_BIT = 0x00008000, + UCC_FAST_SYNC_LEN_16_BIT = 0x0000C000 +}; + +/* UCC fast RTS mode */ +enum ucc_fast_ready_to_send { + UCC_FAST_SEND_IDLES_BETWEEN_FRAMES = 0x00000000, + UCC_FAST_SEND_FLAGS_BETWEEN_FRAMES = 0x00002000 +}; + +/* UCC fast receiver decoding mode */ +enum ucc_fast_rx_decoding_method { + UCC_FAST_RX_ENCODING_NRZ = 0x00000000, + UCC_FAST_RX_ENCODING_NRZI = 0x00000800, + UCC_FAST_RX_ENCODING_RESERVED0 = 0x00001000, + UCC_FAST_RX_ENCODING_RESERVED1 = 0x00001800 +}; + +/* UCC fast transmitter encoding mode */ +enum ucc_fast_tx_encoding_method { + UCC_FAST_TX_ENCODING_NRZ = 0x00000000, + UCC_FAST_TX_ENCODING_NRZI = 0x00000100, + UCC_FAST_TX_ENCODING_RESERVED0 = 0x00000200, + UCC_FAST_TX_ENCODING_RESERVED1 = 0x00000300 +}; + +/* UCC fast CRC length */ +enum ucc_fast_transparent_tcrc { + UCC_FAST_16_BIT_CRC = 0x00000000, + UCC_FAST_CRC_RESERVED0 = 0x00000040, + UCC_FAST_32_BIT_CRC = 0x00000080, + UCC_FAST_CRC_RESERVED1 = 0x000000C0 +}; + +/* Fast UCC initialization structure */ +struct ucc_fast_info { + int ucc_num; + enum qe_clock rx_clock; + enum qe_clock tx_clock; + u32 regs; + int irq; + u32 uccm_mask; + int bd_mem_part; + int brkpt_support; + int grant_support; + int tsa; + int cdp; + int cds; + int ctsp; + int ctss; + int tci; + int txsy; + int rtsm; + int revd; + int rsyn; + u16 max_rx_buf_length; + u16 urfs; + u16 urfet; + u16 urfset; + u16 utfs; + u16 utfet; + u16 utftt; + u16 ufpt; + enum ucc_fast_channel_protocol_mode mode; + enum ucc_fast_transparent_txrx ttx_trx; + enum ucc_fast_tx_encoding_method tenc; + enum ucc_fast_rx_decoding_method renc; + enum ucc_fast_transparent_tcrc tcrc; + enum ucc_fast_sync_len synl; +}; + +struct ucc_fast_private { + struct ucc_fast_info *uf_info; + struct ucc_fast *uf_regs; /* a pointer to memory map of UCC regs. */ + u32 *p_ucce; /* a pointer to the event register in memory. */ + u32 *p_uccm; /* a pointer to the mask register in memory. */ + int enabled_tx; /* Whether channel is enabled for Tx (ENT) */ + int enabled_rx; /* Whether channel is enabled for Rx (ENR) */ + int stopped_tx; /* Whether channel has been stopped for Tx + (STOP_TX, etc.) */ + int stopped_rx; /* Whether channel has been stopped for Rx */ + u32 ucc_fast_tx_virtual_fifo_base_offset;/* pointer to base of Tx + virtual fifo */ + u32 ucc_fast_rx_virtual_fifo_base_offset;/* pointer to base of Rx + virtual fifo */ +#ifdef STATISTICS + u32 tx_frames; /* Transmitted frames counter. */ + u32 rx_frames; /* Received frames counter (only frames + passed to application). */ + u32 tx_discarded; /* Discarded tx frames counter (frames that + were discarded by the driver due to errors). + */ + u32 rx_discarded; /* Discarded rx frames counter (frames that + were discarded by the driver due to errors). + */ +#endif /* STATISTICS */ + u16 mrblr; /* maximum receive buffer length */ +}; + +/* ucc_fast_init + * Initializes Fast UCC according to user provided parameters. + * + * uf_info - (In) pointer to the fast UCC info structure. + * uccf_ret - (Out) pointer to the fast UCC structure. + */ +int ucc_fast_init(struct ucc_fast_info * uf_info, struct ucc_fast_private ** uccf_ret); + +/* ucc_fast_free + * Frees all resources for fast UCC. + * + * uccf - (In) pointer to the fast UCC structure. + */ +void ucc_fast_free(struct ucc_fast_private * uccf); + +/* ucc_fast_enable + * Enables a fast UCC port. + * This routine enables Tx and/or Rx through the General UCC Mode Register. + * + * uccf - (In) pointer to the fast UCC structure. + * mode - (In) TX, RX, or both. + */ +void ucc_fast_enable(struct ucc_fast_private * uccf, enum comm_dir mode); + +/* ucc_fast_disable + * Disables a fast UCC port. + * This routine disables Tx and/or Rx through the General UCC Mode Register. + * + * uccf - (In) pointer to the fast UCC structure. + * mode - (In) TX, RX, or both. + */ +void ucc_fast_disable(struct ucc_fast_private * uccf, enum comm_dir mode); + +/* ucc_fast_irq + * Handles interrupts on fast UCC. + * Called from the general interrupt routine to handle interrupts on fast UCC. + * + * uccf - (In) pointer to the fast UCC structure. + */ +void ucc_fast_irq(struct ucc_fast_private * uccf); + +/* ucc_fast_transmit_on_demand + * Immediately forces a poll of the transmitter for data to be sent. + * Typically, the hardware performs a periodic poll for data that the + * transmit routine has set up to be transmitted. In cases where + * this polling cycle is not soon enough, this optional routine can + * be invoked to force a poll right away, instead. Proper use for + * each transmission for which this functionality is desired is to + * call the transmit routine and then this routine right after. + * + * uccf - (In) pointer to the fast UCC structure. + */ +void ucc_fast_transmit_on_demand(struct ucc_fast_private * uccf); + +u32 ucc_fast_get_qe_cr_subblock(int uccf_num); + +void ucc_fast_dump_regs(struct ucc_fast_private * uccf); + +#endif /* __UCC_FAST_H__ */ diff --git a/include/asm-powerpc/ucc_slow.h b/include/asm-powerpc/ucc_slow.h new file mode 100644 index 000000000000..ca93bc99237e --- /dev/null +++ b/include/asm-powerpc/ucc_slow.h @@ -0,0 +1,289 @@ +/* + * Copyright (C) 2006 Freescale Semicondutor, Inc. All rights reserved. + * + * Authors: Shlomi Gridish <gridish@freescale.com> + * Li Yang <leoli@freescale.com> + * + * Description: + * Internal header file for UCC SLOW unit routines. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#ifndef __UCC_SLOW_H__ +#define __UCC_SLOW_H__ + +#include <linux/kernel.h> + +#include <asm/immap_qe.h> +#include <asm/qe.h> + +#include "ucc.h" + +/* transmit BD's status */ +#define T_R 0x80000000 /* ready bit */ +#define T_PAD 0x40000000 /* add pads to short frames */ +#define T_W 0x20000000 /* wrap bit */ +#define T_I 0x10000000 /* interrupt on completion */ +#define T_L 0x08000000 /* last */ + +#define T_A 0x04000000 /* Address - the data transmitted as address + chars */ +#define T_TC 0x04000000 /* transmit CRC */ +#define T_CM 0x02000000 /* continuous mode */ +#define T_DEF 0x02000000 /* collision on previous attempt to transmit */ +#define T_P 0x01000000 /* Preamble - send Preamble sequence before + data */ +#define T_HB 0x01000000 /* heartbeat */ +#define T_NS 0x00800000 /* No Stop */ +#define T_LC 0x00800000 /* late collision */ +#define T_RL 0x00400000 /* retransmission limit */ +#define T_UN 0x00020000 /* underrun */ +#define T_CT 0x00010000 /* CTS lost */ +#define T_CSL 0x00010000 /* carrier sense lost */ +#define T_RC 0x003c0000 /* retry count */ + +/* Receive BD's status */ +#define R_E 0x80000000 /* buffer empty */ +#define R_W 0x20000000 /* wrap bit */ +#define R_I 0x10000000 /* interrupt on reception */ +#define R_L 0x08000000 /* last */ +#define R_C 0x08000000 /* the last byte in this buffer is a cntl + char */ +#define R_F 0x04000000 /* first */ +#define R_A 0x04000000 /* the first byte in this buffer is address + byte */ +#define R_CM 0x02000000 /* continuous mode */ +#define R_ID 0x01000000 /* buffer close on reception of idles */ +#define R_M 0x01000000 /* Frame received because of promiscuous + mode */ +#define R_AM 0x00800000 /* Address match */ +#define R_DE 0x00800000 /* Address match */ +#define R_LG 0x00200000 /* Break received */ +#define R_BR 0x00200000 /* Frame length violation */ +#define R_NO 0x00100000 /* Rx Non Octet Aligned Packet */ +#define R_FR 0x00100000 /* Framing Error (no stop bit) character + received */ +#define R_PR 0x00080000 /* Parity Error character received */ +#define R_AB 0x00080000 /* Frame Aborted */ +#define R_SH 0x00080000 /* frame is too short */ +#define R_CR 0x00040000 /* CRC Error */ +#define R_OV 0x00020000 /* Overrun */ +#define R_CD 0x00010000 /* CD lost */ +#define R_CL 0x00010000 /* this frame is closed because of a + collision */ + +/* Rx Data buffer must be 4 bytes aligned in most cases.*/ +#define UCC_SLOW_RX_ALIGN 4 +#define UCC_SLOW_MRBLR_ALIGNMENT 4 +#define UCC_SLOW_PRAM_SIZE 0x100 +#define ALIGNMENT_OF_UCC_SLOW_PRAM 64 + +/* UCC Slow Channel Protocol Mode */ +enum ucc_slow_channel_protocol_mode { + UCC_SLOW_CHANNEL_PROTOCOL_MODE_QMC = 0x00000002, + UCC_SLOW_CHANNEL_PROTOCOL_MODE_UART = 0x00000004, + UCC_SLOW_CHANNEL_PROTOCOL_MODE_BISYNC = 0x00000008, +}; + +/* UCC Slow Transparent Transmit CRC (TCRC) */ +enum ucc_slow_transparent_tcrc { + /* 16-bit CCITT CRC (HDLC). (X16 + X12 + X5 + 1) */ + UCC_SLOW_TRANSPARENT_TCRC_CCITT_CRC16 = 0x00000000, + /* CRC16 (BISYNC). (X16 + X15 + X2 + 1) */ + UCC_SLOW_TRANSPARENT_TCRC_CRC16 = 0x00004000, + /* 32-bit CCITT CRC (Ethernet and HDLC) */ + UCC_SLOW_TRANSPARENT_TCRC_CCITT_CRC32 = 0x00008000, +}; + +/* UCC Slow oversampling rate for transmitter (TDCR) */ +enum ucc_slow_tx_oversampling_rate { + /* 1x clock mode */ + UCC_SLOW_OVERSAMPLING_RATE_TX_TDCR_1 = 0x00000000, + /* 8x clock mode */ + UCC_SLOW_OVERSAMPLING_RATE_TX_TDCR_8 = 0x00010000, + /* 16x clock mode */ + UCC_SLOW_OVERSAMPLING_RATE_TX_TDCR_16 = 0x00020000, + /* 32x clock mode */ + UCC_SLOW_OVERSAMPLING_RATE_TX_TDCR_32 = 0x00030000, +}; + +/* UCC Slow Oversampling rate for receiver (RDCR) +*/ +enum ucc_slow_rx_oversampling_rate { + /* 1x clock mode */ + UCC_SLOW_OVERSAMPLING_RATE_RX_RDCR_1 = 0x00000000, + /* 8x clock mode */ + UCC_SLOW_OVERSAMPLING_RATE_RX_RDCR_8 = 0x00004000, + /* 16x clock mode */ + UCC_SLOW_OVERSAMPLING_RATE_RX_RDCR_16 = 0x00008000, + /* 32x clock mode */ + UCC_SLOW_OVERSAMPLING_RATE_RX_RDCR_32 = 0x0000c000, +}; + +/* UCC Slow Transmitter encoding method (TENC) +*/ +enum ucc_slow_tx_encoding_method { + UCC_SLOW_TRANSMITTER_ENCODING_METHOD_TENC_NRZ = 0x00000000, + UCC_SLOW_TRANSMITTER_ENCODING_METHOD_TENC_NRZI = 0x00000100 +}; + +/* UCC Slow Receiver decoding method (RENC) +*/ +enum ucc_slow_rx_decoding_method { + UCC_SLOW_RECEIVER_DECODING_METHOD_RENC_NRZ = 0x00000000, + UCC_SLOW_RECEIVER_DECODING_METHOD_RENC_NRZI = 0x00000800 +}; + +/* UCC Slow Diagnostic mode (DIAG) +*/ +enum ucc_slow_diag_mode { + UCC_SLOW_DIAG_MODE_NORMAL = 0x00000000, + UCC_SLOW_DIAG_MODE_LOOPBACK = 0x00000040, + UCC_SLOW_DIAG_MODE_ECHO = 0x00000080, + UCC_SLOW_DIAG_MODE_LOOPBACK_ECHO = 0x000000c0 +}; + +struct ucc_slow_info { + int ucc_num; + enum qe_clock rx_clock; + enum qe_clock tx_clock; + struct ucc_slow *us_regs; + int irq; + u16 uccm_mask; + int data_mem_part; + int init_tx; + int init_rx; + u32 tx_bd_ring_len; + u32 rx_bd_ring_len; + int rx_interrupts; + int brkpt_support; + int grant_support; + int tsa; + int cdp; + int cds; + int ctsp; + int ctss; + int rinv; + int tinv; + int rtsm; + int rfw; + int tci; + int tend; + int tfl; + int txsy; + u16 max_rx_buf_length; + enum ucc_slow_transparent_tcrc tcrc; + enum ucc_slow_channel_protocol_mode mode; + enum ucc_slow_diag_mode diag; + enum ucc_slow_tx_oversampling_rate tdcr; + enum ucc_slow_rx_oversampling_rate rdcr; + enum ucc_slow_tx_encoding_method tenc; + enum ucc_slow_rx_decoding_method renc; +}; + +struct ucc_slow_private { + struct ucc_slow_info *us_info; + struct ucc_slow *us_regs; /* a pointer to memory map of UCC regs */ + struct ucc_slow_pram *us_pram; /* a pointer to the parameter RAM */ + u32 us_pram_offset; + int enabled_tx; /* Whether channel is enabled for Tx (ENT) */ + int enabled_rx; /* Whether channel is enabled for Rx (ENR) */ + int stopped_tx; /* Whether channel has been stopped for Tx + (STOP_TX, etc.) */ + int stopped_rx; /* Whether channel has been stopped for Rx */ + struct list_head confQ; /* frames passed to chip waiting for tx */ + u32 first_tx_bd_mask; /* mask is used in Tx routine to save status + and length for first BD in a frame */ + u32 tx_base_offset; /* first BD in Tx BD table offset (In MURAM) */ + u32 rx_base_offset; /* first BD in Rx BD table offset (In MURAM) */ + u8 *confBd; /* next BD for confirm after Tx */ + u8 *tx_bd; /* next BD for new Tx request */ + u8 *rx_bd; /* next BD to collect after Rx */ + void *p_rx_frame; /* accumulating receive frame */ + u16 *p_ucce; /* a pointer to the event register in memory. + */ + u16 *p_uccm; /* a pointer to the mask register in memory */ + u16 saved_uccm; /* a saved mask for the RX Interrupt bits */ +#ifdef STATISTICS + u32 tx_frames; /* Transmitted frames counters */ + u32 rx_frames; /* Received frames counters (only frames + passed to application) */ + u32 rx_discarded; /* Discarded frames counters (frames that + were discarded by the driver due to + errors) */ +#endif /* STATISTICS */ +}; + +/* ucc_slow_init + * Initializes Slow UCC according to provided parameters. + * + * us_info - (In) pointer to the slow UCC info structure. + * uccs_ret - (Out) pointer to the slow UCC structure. + */ +int ucc_slow_init(struct ucc_slow_info * us_info, struct ucc_slow_private ** uccs_ret); + +/* ucc_slow_free + * Frees all resources for slow UCC. + * + * uccs - (In) pointer to the slow UCC structure. + */ +void ucc_slow_free(struct ucc_slow_private * uccs); + +/* ucc_slow_enable + * Enables a fast UCC port. + * This routine enables Tx and/or Rx through the General UCC Mode Register. + * + * uccs - (In) pointer to the slow UCC structure. + * mode - (In) TX, RX, or both. + */ +void ucc_slow_enable(struct ucc_slow_private * uccs, enum comm_dir mode); + +/* ucc_slow_disable + * Disables a fast UCC port. + * This routine disables Tx and/or Rx through the General UCC Mode Register. + * + * uccs - (In) pointer to the slow UCC structure. + * mode - (In) TX, RX, or both. + */ +void ucc_slow_disable(struct ucc_slow_private * uccs, enum comm_dir mode); + +/* ucc_slow_poll_transmitter_now + * Immediately forces a poll of the transmitter for data to be sent. + * Typically, the hardware performs a periodic poll for data that the + * transmit routine has set up to be transmitted. In cases where + * this polling cycle is not soon enough, this optional routine can + * be invoked to force a poll right away, instead. Proper use for + * each transmission for which this functionality is desired is to + * call the transmit routine and then this routine right after. + * + * uccs - (In) pointer to the slow UCC structure. + */ +void ucc_slow_poll_transmitter_now(struct ucc_slow_private * uccs); + +/* ucc_slow_graceful_stop_tx + * Smoothly stops transmission on a specified slow UCC. + * + * uccs - (In) pointer to the slow UCC structure. + */ +void ucc_slow_graceful_stop_tx(struct ucc_slow_private * uccs); + +/* ucc_slow_stop_tx + * Stops transmission on a specified slow UCC. + * + * uccs - (In) pointer to the slow UCC structure. + */ +void ucc_slow_stop_tx(struct ucc_slow_private * uccs); + +/* ucc_slow_restart_x + * Restarts transmitting on a specified slow UCC. + * + * uccs - (In) pointer to the slow UCC structure. + */ +void ucc_slow_restart_x(struct ucc_slow_private * uccs); + +u32 ucc_slow_get_qe_cr_subblock(int uccs_num); + +#endif /* __UCC_SLOW_H__ */ diff --git a/include/asm-powerpc/xmon.h b/include/asm-powerpc/xmon.h index 43f7129984c7..f1d337ed68d5 100644 --- a/include/asm-powerpc/xmon.h +++ b/include/asm-powerpc/xmon.h @@ -1,12 +1,22 @@ -#ifndef __PPC_XMON_H -#define __PPC_XMON_H -#ifdef __KERNEL__ +#ifndef __ASM_POWERPC_XMON_H +#define __ASM_POWERPC_XMON_H -struct pt_regs; +/* + * Copyrignt (C) 2006 IBM Corp + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ -extern int xmon(struct pt_regs *excp); -extern void xmon_printf(const char *fmt, ...); -extern void xmon_init(int); +#ifdef __KERNEL__ +#ifdef CONFIG_XMON +extern void xmon_setup(void); +#else +static inline void xmon_setup(void) { }; #endif -#endif + +#endif /* __KERNEL __ */ +#endif /* __ASM_POWERPC_XMON_H */ diff --git a/include/linux/fsl_devices.h b/include/linux/fsl_devices.h index 16fbe59edeb1..3da29e2d524a 100644 --- a/include/linux/fsl_devices.h +++ b/include/linux/fsl_devices.h @@ -46,18 +46,17 @@ struct gianfar_platform_data { /* device specific information */ - u32 device_flags; - + u32 device_flags; /* board specific information */ - u32 board_flags; - u32 bus_id; - u32 phy_id; - u8 mac_addr[6]; + u32 board_flags; + u32 bus_id; + u32 phy_id; + u8 mac_addr[6]; }; struct gianfar_mdio_data { /* board specific information */ - int irq[32]; + int irq[32]; }; /* Flags related to gianfar device features */ @@ -76,14 +75,13 @@ struct gianfar_mdio_data { struct fsl_i2c_platform_data { /* device specific information */ - u32 device_flags; + u32 device_flags; }; /* Flags related to I2C device features */ #define FSL_I2C_DEV_SEPARATE_DFSRR 0x00000001 #define FSL_I2C_DEV_CLOCK_5200 0x00000002 - enum fsl_usb2_operating_modes { FSL_USB2_MPH_HOST, FSL_USB2_DR_HOST, @@ -101,9 +99,9 @@ enum fsl_usb2_phy_modes { struct fsl_usb2_platform_data { /* board specific information */ - enum fsl_usb2_operating_modes operating_mode; - enum fsl_usb2_phy_modes phy_mode; - unsigned int port_enables; + enum fsl_usb2_operating_modes operating_mode; + enum fsl_usb2_phy_modes phy_mode; + unsigned int port_enables; }; /* Flags in fsl_usb2_mph_platform_data */ @@ -121,5 +119,44 @@ struct fsl_spi_platform_data { u32 sysclk; }; -#endif /* _FSL_DEVICE_H_ */ -#endif /* __KERNEL__ */ +/* Ethernet interface (phy management and speed) +*/ +enum enet_interface { + ENET_10_MII, /* 10 Base T, MII interface */ + ENET_10_RMII, /* 10 Base T, RMII interface */ + ENET_10_RGMII, /* 10 Base T, RGMII interface */ + ENET_100_MII, /* 100 Base T, MII interface */ + ENET_100_RMII, /* 100 Base T, RMII interface */ + ENET_100_RGMII, /* 100 Base T, RGMII interface */ + ENET_1000_GMII, /* 1000 Base T, GMII interface */ + ENET_1000_RGMII, /* 1000 Base T, RGMII interface */ + ENET_1000_TBI, /* 1000 Base T, TBI interface */ + ENET_1000_RTBI /* 1000 Base T, RTBI interface */ +}; + +struct ucc_geth_platform_data { + /* device specific information */ + u32 device_flags; + u32 phy_reg_addr; + + /* board specific information */ + u32 board_flags; + u8 rx_clock; + u8 tx_clock; + u32 phy_id; + enum enet_interface phy_interface; + u32 phy_interrupt; + u8 mac_addr[6]; +}; + +/* Flags related to UCC Gigabit Ethernet device features */ +#define FSL_UGETH_DEV_HAS_GIGABIT 0x00000001 +#define FSL_UGETH_DEV_HAS_COALESCE 0x00000002 +#define FSL_UGETH_DEV_HAS_RMON 0x00000004 + +/* Flags in ucc_geth_platform_data */ +#define FSL_UGETH_BRD_HAS_PHY_INTR 0x00000001 + /* if not set use a timer */ + +#endif /* _FSL_DEVICE_H_ */ +#endif /* __KERNEL__ */ |
