diff options
| -rw-r--r-- | Documentation/hwmon/w83791d | 113 | ||||
| -rw-r--r-- | drivers/hwmon/Kconfig | 10 | ||||
| -rw-r--r-- | drivers/hwmon/Makefile | 1 | ||||
| -rw-r--r-- | drivers/hwmon/w83791d.c | 1255 |
4 files changed, 1379 insertions, 0 deletions
diff --git a/Documentation/hwmon/w83791d b/Documentation/hwmon/w83791d new file mode 100644 index 000000000000..83a3836289c2 --- /dev/null +++ b/Documentation/hwmon/w83791d @@ -0,0 +1,113 @@ +Kernel driver w83791d +===================== + +Supported chips: + * Winbond W83791D + Prefix: 'w83791d' + Addresses scanned: I2C 0x2c - 0x2f + Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83791Da.pdf + +Author: Charles Spirakis <bezaur@gmail.com> + +This driver was derived from the w83781d.c and w83792d.c source files. + +Credits: + w83781d.c: + Frodo Looijaard <frodol@dds.nl>, + Philip Edelbrock <phil@netroedge.com>, + and Mark Studebaker <mdsxyz123@yahoo.com> + w83792d.c: + Chunhao Huang <DZShen@Winbond.com.tw>, + Rudolf Marek <r.marek@sh.cvut.cz> + +Module Parameters +----------------- + +* init boolean + (default 0) + Use 'init=1' to have the driver do extra software initializations. + The default behavior is to do the minimum initialization possible + and depend on the BIOS to properly setup the chip. If you know you + have a w83791d and you're having problems, try init=1 before trying + reset=1. + +* reset boolean + (default 0) + Use 'reset=1' to reset the chip (via index 0x40, bit 7). The default + behavior is no chip reset to preserve BIOS settings. + +* force_subclients=bus,caddr,saddr,saddr + This is used to force the i2c addresses for subclients of + a certain chip. Example usage is `force_subclients=0,0x2f,0x4a,0x4b' + to force the subclients of chip 0x2f on bus 0 to i2c addresses + 0x4a and 0x4b. + + +Description +----------- + +This driver implements support for the Winbond W83791D chip. + +Detection of the chip can sometimes be foiled because it can be in an +internal state that allows no clean access (Bank with ID register is not +currently selected). If you know the address of the chip, use a 'force' +parameter; this will put it into a more well-behaved state first. + +The driver implements three temperature sensors, five fan rotation speed +sensors, and ten voltage sensors. + +Temperatures are measured in degrees Celsius and measurement resolution is 1 +degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when +the temperature gets higher than the Overtemperature Shutdown value; it stays +on until the temperature falls below the Hysteresis value. + +Fan rotation speeds are reported in RPM (rotations per minute). An alarm is +triggered if the rotation speed has dropped below a programmable limit. Fan +readings can be divided by a programmable divider (1, 2, 4, 8 for fan 1/2/3 +and 1, 2, 4, 8, 16, 32, 64 or 128 for fan 4/5) to give the readings more +range or accuracy. + +Voltage sensors (also known as IN sensors) report their values in millivolts. +An alarm is triggered if the voltage has crossed a programmable minimum +or maximum limit. + +Alarms are provided as output from a "realtime status register". The +following bits are defined: + +bit - alarm on: +0 - Vcore +1 - VINR0 +2 - +3.3VIN +3 - 5VDD +4 - temp1 +5 - temp2 +6 - fan1 +7 - fan2 +8 - +12VIN +9 - -12VIN +10 - -5VIN +11 - fan3 +12 - chassis +13 - temp3 +14 - VINR1 +15 - reserved +16 - tart1 +17 - tart2 +18 - tart3 +19 - VSB +20 - VBAT +21 - fan4 +22 - fan5 +23 - reserved + +When an alarm goes off, you can be warned by a beeping signal through your +computer speaker. It is possible to enable all beeping globally, or only +the beeping for some alarms. + +The driver only reads the chip values each 3 seconds; reading them more +often will do no harm, but will return 'old' values. + +W83791D TODO: +--------------- +Provide a patch for per-file alarms as discussed on the mailing list +Provide a patch for smart-fan control (still need appropriate motherboard/fans) diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 9cf3d9c5962f..9384b85b893b 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -406,6 +406,16 @@ config SENSORS_W83781D This driver can also be built as a module. If so, the module will be called w83781d. +config SENSORS_W83791D + tristate "Winbond W83791D" + depends on HWMON && I2C && EXPERIMENTAL + select HWMON_VID + help + If you say yes here you get support for the Winbond W83791D chip. + + This driver can also be built as a module. If so, the module + will be called w83791d. + config SENSORS_W83792D tristate "Winbond W83792D" depends on HWMON && I2C && EXPERIMENTAL diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index d0904593c9ea..db72b1415e7f 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_SENSORS_ASB100) += asb100.o obj-$(CONFIG_SENSORS_W83627HF) += w83627hf.o obj-$(CONFIG_SENSORS_W83792D) += w83792d.o obj-$(CONFIG_SENSORS_W83781D) += w83781d.o +obj-$(CONFIG_SENSORS_W83791D) += w83791d.o obj-$(CONFIG_SENSORS_ADM1021) += adm1021.o obj-$(CONFIG_SENSORS_ADM1025) += adm1025.o diff --git a/drivers/hwmon/w83791d.c b/drivers/hwmon/w83791d.c new file mode 100644 index 000000000000..eec43abd57fb --- /dev/null +++ b/drivers/hwmon/w83791d.c @@ -0,0 +1,1255 @@ +/* + w83791d.c - Part of lm_sensors, Linux kernel modules for hardware + monitoring + + Copyright (C) 2006 Charles Spirakis <bezaur@gmail.com> + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the Free Software + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +*/ + +/* + Supports following chips: + + Chip #vin #fanin #pwm #temp wchipid vendid i2c ISA + w83791d 10 5 3 3 0x71 0x5ca3 yes no + + The w83791d chip appears to be part way between the 83781d and the + 83792d. Thus, this file is derived from both the w83792d.c and + w83781d.c files, but its output is more along the lines of the + 83781d (which means there are no changes to the user-mode sensors + program which treats the 83791d as an 83781d). +*/ + +#include <linux/config.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/i2c.h> +#include <linux/hwmon.h> +#include <linux/hwmon-vid.h> +#include <linux/hwmon-sysfs.h> +#include <linux/err.h> +#include <linux/mutex.h> + +#define NUMBER_OF_VIN 10 +#define NUMBER_OF_FANIN 5 +#define NUMBER_OF_TEMPIN 3 + +/* Addresses to scan */ +static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END }; + +/* Insmod parameters */ +I2C_CLIENT_INSMOD_1(w83791d); +I2C_CLIENT_MODULE_PARM(force_subclients, "List of subclient addresses: " + "{bus, clientaddr, subclientaddr1, subclientaddr2}"); + +static int reset; +module_param(reset, bool, 0); +MODULE_PARM_DESC(reset, "Set to one to force a hardware chip reset"); + +static int init; +module_param(init, bool, 0); +MODULE_PARM_DESC(init, "Set to one to force extra software initialization"); + +/* The W83791D registers */ +static const u8 W83791D_REG_IN[NUMBER_OF_VIN] = { + 0x20, /* VCOREA in DataSheet */ + 0x21, /* VINR0 in DataSheet */ + 0x22, /* +3.3VIN in DataSheet */ + 0x23, /* VDD5V in DataSheet */ + 0x24, /* +12VIN in DataSheet */ + 0x25, /* -12VIN in DataSheet */ + 0x26, /* -5VIN in DataSheet */ + 0xB0, /* 5VSB in DataSheet */ + 0xB1, /* VBAT in DataSheet */ + 0xB2 /* VINR1 in DataSheet */ +}; + +static const u8 W83791D_REG_IN_MAX[NUMBER_OF_VIN] = { + 0x2B, /* VCOREA High Limit in DataSheet */ + 0x2D, /* VINR0 High Limit in DataSheet */ + 0x2F, /* +3.3VIN High Limit in DataSheet */ + 0x31, /* VDD5V High Limit in DataSheet */ + 0x33, /* +12VIN High Limit in DataSheet */ + 0x35, /* -12VIN High Limit in DataSheet */ + 0x37, /* -5VIN High Limit in DataSheet */ + 0xB4, /* 5VSB High Limit in DataSheet */ + 0xB6, /* VBAT High Limit in DataSheet */ + 0xB8 /* VINR1 High Limit in DataSheet */ +}; +static const u8 W83791D_REG_IN_MIN[NUMBER_OF_VIN] = { + 0x2C, /* VCOREA Low Limit in DataSheet */ + 0x2E, /* VINR0 Low Limit in DataSheet */ + 0x30, /* +3.3VIN Low Limit in DataSheet */ + 0x32, /* VDD5V Low Limit in DataSheet */ + 0x34, /* +12VIN Low Limit in DataSheet */ + 0x36, /* -12VIN Low Limit in DataSheet */ + 0x38, /* -5VIN Low Limit in DataSheet */ + 0xB5, /* 5VSB Low Limit in DataSheet */ + 0xB7, /* VBAT Low Limit in DataSheet */ + 0xB9 /* VINR1 Low Limit in DataSheet */ +}; +static const u8 W83791D_REG_FAN[NUMBER_OF_FANIN] = { + 0x28, /* FAN 1 Count in DataSheet */ + 0x29, /* FAN 2 Count in DataSheet */ + 0x2A, /* FAN 3 Count in DataSheet */ + 0xBA, /* FAN 4 Count in DataSheet */ + 0xBB, /* FAN 5 Count in DataSheet */ +}; +static const u8 W83791D_REG_FAN_MIN[NUMBER_OF_FANIN] = { + 0x3B, /* FAN 1 Count Low Limit in DataSheet */ + 0x3C, /* FAN 2 Count Low Limit in DataSheet */ + 0x3D, /* FAN 3 Count Low Limit in DataSheet */ + 0xBC, /* FAN 4 Count Low Limit in DataSheet */ + 0xBD, /* FAN 5 Count Low Limit in DataSheet */ +}; + +static const u8 W83791D_REG_FAN_CFG[2] = { + 0x84, /* FAN 1/2 configuration */ + 0x95, /* FAN 3 configuration */ +}; + +static const u8 W83791D_REG_FAN_DIV[3] = { + 0x47, /* contains FAN1 and FAN2 Divisor */ + 0x4b, /* contains FAN3 Divisor */ + 0x5C, /* contains FAN4 and FAN5 Divisor */ +}; + +#define W83791D_REG_BANK 0x4E +#define W83791D_REG_TEMP2_CONFIG 0xC2 +#define W83791D_REG_TEMP3_CONFIG 0xCA + +static const u8 W83791D_REG_TEMP1[3] = { + 0x27, /* TEMP 1 in DataSheet */ + 0x39, /* TEMP 1 Over in DataSheet */ + 0x3A, /* TEMP 1 Hyst in DataSheet */ +}; + +static const u8 W83791D_REG_TEMP_ADD[2][6] = { + {0xC0, /* TEMP 2 in DataSheet */ + 0xC1, /* TEMP 2(0.5 deg) in DataSheet */ + 0xC5, /* TEMP 2 Over High part in DataSheet */ + 0xC6, /* TEMP 2 Over Low part in DataSheet */ + 0xC3, /* TEMP 2 Thyst High part in DataSheet */ + 0xC4}, /* TEMP 2 Thyst Low part in DataSheet */ + {0xC8, /* TEMP 3 in DataSheet */ + 0xC9, /* TEMP 3(0.5 deg) in DataSheet */ + 0xCD, /* TEMP 3 Over High part in DataSheet */ + 0xCE, /* TEMP 3 Over Low part in DataSheet */ + 0xCB, /* TEMP 3 Thyst High part in DataSheet */ + 0xCC} /* TEMP 3 Thyst Low part in DataSheet */ +}; + +#define W83791D_REG_BEEP_CONFIG 0x4D + +static const u8 W83791D_REG_BEEP_CTRL[3] = { + 0x56, /* BEEP Control Register 1 */ + 0x57, /* BEEP Control Register 2 */ + 0xA3, /* BEEP Control Register 3 */ +}; + +#define W83791D_REG_CONFIG 0x40 +#define W83791D_REG_VID_FANDIV 0x47 +#define W83791D_REG_DID_VID4 0x49 +#define W83791D_REG_WCHIPID 0x58 +#define W83791D_REG_CHIPMAN 0x4F +#define W83791D_REG_PIN 0x4B +#define W83791D_REG_I2C_SUBADDR 0x4A + +#define W83791D_REG_ALARM1 0xA9 /* realtime status register1 */ +#define W83791D_REG_ALARM2 0xAA /* realtime status register2 */ +#define W83791D_REG_ALARM3 0xAB /* realtime status register3 */ + +#define W83791D_REG_VBAT 0x5D +#define W83791D_REG_I2C_ADDR 0x48 + +/* The SMBus locks itself. The Winbond W83791D has a bank select register + (index 0x4e), but the driver only accesses registers in bank 0. Since + we don't switch banks, we don't need any special code to handle + locking access between bank switches */ +static inline int w83791d_read(struct i2c_client *client, u8 reg) +{ + return i2c_smbus_read_byte_data(client, reg); +} + +static inline int w83791d_write(struct i2c_client *client, u8 reg, u8 value) +{ + return i2c_smbus_write_byte_data(client, reg, value); +} + +/* The analog voltage inputs have 16mV LSB. Since the sysfs output is + in mV as would be measured on the chip input pin, need to just + multiply/divide by 16 to translate from/to register values. */ +#define IN_TO_REG(val) (SENSORS_LIMIT((((val) + 8) / 16), 0, 255)) +#define IN_FROM_REG(val) ((val) * 16) + +static u8 fan_to_reg(long rpm, int div) +{ + if (rpm == 0) + return 255; + rpm = SENSORS_LIMIT(rpm, 1, 1000000); + return SENSORS_LIMIT((1350000 + rpm * div / 2) / (rpm * div), 1, 254); +} + +#define FAN_FROM_REG(val,div) ((val) == 0 ? -1 : \ + ((val) == 255 ? 0 : \ + 1350000 / ((val) * (div)))) + +/* for temp1 which is 8-bit resolution, LSB = 1 degree Celsius */ +#define TEMP1_FROM_REG(val) ((val) * 1000) +#define TEMP1_TO_REG(val) ((val) <= -128000 ? -128 : \ + (val) >= 127000 ? 127 : \ + (val) < 0 ? ((val) - 500) / 1000 : \ + ((val) + 500) / 1000) + +/* for temp2 and temp3 which are 9-bit resolution, LSB = 0.5 degree Celsius + Assumes the top 8 bits are the integral amount and the bottom 8 bits + are the fractional amount. Since we only have 0.5 degree resolution, + the bottom 7 bits will always be zero */ +#define TEMP23_FROM_REG(val) ((val) / 128 * 500) +#define TEMP23_TO_REG(val) ((val) <= -128000 ? 0x8000 : \ + (val) >= 127500 ? 0x7F80 : \ + (val) < 0 ? ((val) - 250) / 500 * 128 : \ + ((val) + 250) / 500 * 128) + + +#define BEEP_MASK_TO_REG(val) ((val) & 0xffffff) +#define BEEP_MASK_FROM_REG(val) ((val) & 0xffffff) + +#define DIV_FROM_REG(val) (1 << (val)) + +static u8 div_to_reg(int nr, long val) +{ + int i; + int max; + + /* first three fan's divisor max out at 8, rest max out at 128 */ + max = (nr < 3) ? 8 : 128; + val = SENSORS_LIMIT(val, 1, max) >> 1; + for (i = 0; i < 7; i++) { + if (val == 0) + break; + val >>= 1; + } + return (u8) i; +} + +struct w83791d_data { + struct i2c_client client; + struct class_device *class_dev; + struct mutex update_lock; + + char valid; /* !=0 if following fields are valid */ + unsigned long last_updated; /* In jiffies */ + + /* array of 2 pointers to subclients */ + struct i2c_client *lm75[2]; + + /* volts */ + u8 in[NUMBER_OF_VIN]; /* Register value */ + u8 in_max[NUMBER_OF_VIN]; /* Register value */ + u8 in_min[NUMBER_OF_VIN]; /* Register value */ + + /* fans */ + u8 fan[NUMBER_OF_FANIN]; /* Register value */ + u8 fan_min[NUMBER_OF_FANIN]; /* Register value */ + u8 fan_div[NUMBER_OF_FANIN]; /* Register encoding, shifted right */ + + /* Temperature sensors */ + + s8 temp1[3]; /* current, over, thyst */ + s16 temp_add[2][3]; /* fixed point value. Top 8 bits are the + integral part, bottom 8 bits are the + fractional part. We only use the top + 9 bits as the resolution is only + to the 0.5 degree C... + two sensors with three values + (cur, over, hyst) */ + + /* Misc */ + u32 alarms; /* realtime status register encoding,combined */ + u8 beep_enable; /* Global beep enable */ + u32 beep_mask; /* Mask off specific beeps */ + u8 vid; /* Register encoding, combined */ + u8 vrm; /* hwmon-vid */ +}; + +static int w83791d_attach_adapter(struct i2c_adapter *adapter); +static int w83791d_detect(struct i2c_adapter *adapter, int address, int kind); +static int w83791d_detach_client(struct i2c_client *client); + +static int w83791d_read(struct i2c_client *client, u8 register); +static int w83791d_write(struct i2c_client *client, u8 register, u8 value); +static struct w83791d_data *w83791d_update_device(struct device *dev); + +#ifdef DEBUG +static void w83791d_print_debug(struct w83791d_data *data, struct device *dev); +#endif + +static void w83791d_init_client(struct i2c_client *client); + +static struct i2c_driver w83791d_driver = { + .driver = { + .name = "w83791d", + }, + .attach_adapter = w83791d_attach_adapter, + .detach_client = w83791d_detach_client, +}; + +/* following are the sysfs callback functions */ +#define show_in_reg(reg) \ +static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \ + char *buf) \ +{ \ + struct sensor_device_attribute *sensor_attr = \ + to_sensor_dev_attr(attr); \ + struct w83791d_data *data = w83791d_update_device(dev); \ + int nr = sensor_attr->index; \ + return sprintf(buf,"%d\n", IN_FROM_REG(data->reg[nr])); \ +} + +show_in_reg(in); +show_in_reg(in_min); +show_in_reg(in_max); + +#define store_in_reg(REG, reg) \ +static ssize_t store_in_##reg(struct device *dev, \ + struct device_attribute *attr, \ + const char *buf, size_t count) \ +{ \ + struct sensor_device_attribute *sensor_attr = \ + to_sensor_dev_attr(attr); \ + struct i2c_client *client = to_i2c_client(dev); \ + struct w83791d_data *data = i2c_get_clientdata(client); \ + unsigned long val = simple_strtoul(buf, NULL, 10); \ + int nr = sensor_attr->index; \ + \ + mutex_lock(&data->update_lock); \ + data->in_##reg[nr] = IN_TO_REG(val); \ + w83791d_write(client, W83791D_REG_IN_##REG[nr], data->in_##reg[nr]); \ + mutex_unlock(&data->update_lock); \ + \ + return count; \ +} +store_in_reg(MIN, min); +store_in_reg(MAX, max); + +static struct sensor_device_attribute sda_in_input[] = { + SENSOR_ATTR(in0_input, S_IRUGO, show_in, NULL, 0), + SENSOR_ATTR(in1_input, S_IRUGO, show_in, NULL, 1), + SENSOR_ATTR(in2_input, S_IRUGO, show_in, NULL, 2), + SENSOR_ATTR(in3_input, S_IRUGO, show_in, NULL, 3), + SENSOR_ATTR(in4_input, S_IRUGO, show_in, NULL, 4), + SENSOR_ATTR(in5_input, S_IRUGO, show_in, NULL, 5), + SENSOR_ATTR(in6_input, S_IRUGO, show_in, NULL, 6), + SENSOR_ATTR(in7_input, S_IRUGO, show_in, NULL, 7), + SENSOR_ATTR(in8_input, S_IRUGO, show_in, NULL, 8), + SENSOR_ATTR(in9_input, S_IRUGO, show_in, NULL, 9), +}; + +static struct sensor_device_attribute sda_in_min[] = { + SENSOR_ATTR(in0_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 0), + SENSOR_ATTR(in1_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 1), + SENSOR_ATTR(in2_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 2), + SENSOR_ATTR(in3_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 3), + SENSOR_ATTR(in4_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 4), + SENSOR_ATTR(in5_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 5), + SENSOR_ATTR(in6_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 6), + SENSOR_ATTR(in7_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 7), + SENSOR_ATTR(in8_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 8), + SENSOR_ATTR(in9_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 9), +}; + +static struct sensor_device_attribute sda_in_max[] = { + SENSOR_ATTR(in0_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 0), + SENSOR_ATTR(in1_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 1), + SENSOR_ATTR(in2_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 2), + SENSOR_ATTR(in3_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 3), + SENSOR_ATTR(in4_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 4), + SENSOR_ATTR(in5_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 5), + SENSOR_ATTR(in6_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 6), + SENSOR_ATTR(in7_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 7), + SENSOR_ATTR(in8_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 8), + SENSOR_ATTR(in9_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 9), +}; + +#define show_fan_reg(reg) \ +static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \ + char *buf) \ +{ \ + struct sensor_device_attribute *sensor_attr = \ + to_sensor_dev_attr(attr); \ + struct w83791d_data *data = w83791d_update_device(dev); \ + int nr = sensor_attr->index; \ + return sprintf(buf,"%d\n", \ + FAN_FROM_REG(data->reg[nr], DIV_FROM_REG(data->fan_div[nr]))); \ +} + +show_fan_reg(fan); +show_fan_reg(fan_min); + +static ssize_t store_fan_min(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + struct i2c_client *client = to_i2c_client(dev); + struct w83791d_data *data = i2c_get_clientdata(client); + unsigned long val = simple_strtoul(buf, NULL, 10); + int nr = sensor_attr->index; + + mutex_lock(&data->update_lock); + data->fan_min[nr] = fan_to_reg(val, DIV_FROM_REG(data->fan_div[nr])); + w83791d_write(client, W83791D_REG_FAN_MIN[nr], data->fan_min[nr]); + mutex_unlock(&data->update_lock); + + return count; +} + +static ssize_t show_fan_div(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + int nr = sensor_attr->index; + struct w83791d_data *data = w83791d_update_device(dev); + return sprintf(buf, "%u\n", DIV_FROM_REG(data->fan_div[nr])); +} + +/* Note: we save and restore the fan minimum here, because its value is + determined in part by the fan divisor. This follows the principle of + least suprise; the user doesn't expect the fan minimum to change just + because the divisor changed. */ +static ssize_t store_fan_div(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); + struct i2c_client *client = to_i2c_client(dev); + struct w83791d_data *data = i2c_get_clientdata(client); + int nr = sensor_attr->index; + unsigned long min; + u8 tmp_fan_div; + u8 fan_div_reg; + int indx = 0; + u8 keep_mask = 0; + u8 new_shift = 0; + + /* Save fan_min */ + min = FAN_FROM_REG(data->fan_min[nr], DIV_FROM_REG(data->fan_div[nr])); + + mutex_lock(&data->update_lock); + data->fan_div[nr] = div_to_reg(nr, simple_strtoul(buf, NULL, 10)); + + switch (nr) { + case 0: + indx = 0; + keep_mask = 0xcf; + new_shift = 4; + break; + case 1: + indx = 0; + keep_mask = 0x3f; + new_shift = 6; + break; + case 2: + indx = 1; + keep_mask = 0x3f; + new_shift = 6; + break; + case 3: + indx = 2; + keep_mask = 0xf8; + new_shift = 0; + break; + case 4: + indx = 2; + keep_mask = 0x8f; + new_shift = 4; + break; +#ifdef DEBUG + default: + dev_warn(dev, "store_fan_div: Unexpected nr seen: %d\n", nr); + count = -EINVAL; + goto err_exit; +#endif + } + + fan_div_reg = w83791d_read(client, W83791D_REG_FAN_DIV[indx]) + & keep_mask; + tmp_fan_div = (data->fan_div[nr] << new_shift) & ~keep_mask; + + w83791d_write(client, W83791D_REG_FAN_DIV[indx], + fan_div_reg | tmp_fan_div); + + /* Restore fan_min */ + data->fan_min[nr] = fan_to_reg(min, DIV_FROM_REG(data->fan_div[nr])); + w83791d_write(client, W83791D_REG_FAN_MIN[nr], data->fan_min[nr]); + +#ifdef DEBUG +err_exit: +#endif + mutex_unlock(&data->update_lock); + + return count; +} + +static struct sensor_device_attribute sda_fan_input[] = { + SENSOR_ATTR(fan1_input, S_IRUGO, show_fan, NULL, 0), + SENSOR_ATTR(fan2_input, S_IRUGO, show_fan, NULL, 1), + SENSOR_ATTR(fan3_input, S_IRUGO, show_fan, NULL, 2), + SENSOR_ATTR(fan4_input, S_IRUGO, show_fan, NULL, 3), + SENSOR_ATTR(fan5_input, S_IRUGO, show_fan, NULL, 4), +}; + +static struct sensor_device_attribute sda_fan_min[] = { + SENSOR_ATTR(fan1_min, S_IWUSR | S_IRUGO, + show_fan_min, store_fan_min, 0), + SENSOR_ATTR(fan2_min, S_IWUSR | S_IRUGO, + show_fan_min, store_fan_min, 1), + SENSOR_ATTR(fan3_min, S_IWUSR | S_IRUGO, + show_fan_min, store_fan_min, 2), + SENSOR_ATTR(fan4_min, S_IWUSR | S_IRUGO, + show_fan_min, store_fan_min, 3), + SENSOR_ATTR(fan5_min, S_IWUSR | S_IRUGO, + show_fan_min, store_fan_min, 4), +}; + +static struct sensor_device_attribute sda_fan_div[] = { + SENSOR_ATTR(fan1_div, S_IWUSR | S_IRUGO, + show_fan_div, store_fan_div, 0), + SENSOR_ATTR(fan2_div, S_IWUSR | S_IRUGO, + show_fan_div, store_fan_div, 1), + SENSOR_ATTR(fan3_div, S_IWUSR | S_IRUGO, + show_fan_div, store_fan_div, 2), + SENSOR_ATTR(fan4_div, S_IWUSR | S_IRUGO, + show_fan_div, store_fan_div, 3), + SENSOR_ATTR(fan5_div, S_IWUSR | S_IRUGO, + show_fan_div, store_fan_div, 4), +}; + +/* read/write the temperature1, includes measured value and limits */ +static ssize_t show_temp1(struct device *dev, struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct w83791d_data *data = w83791d_update_device(dev); + return sprintf(buf, "%d\n", TEMP1_FROM_REG(data->temp1[attr->index])); +} + +static ssize_t store_temp1(struct device *dev, struct device_attribute *devattr, + const char *buf, size_t count) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct w83791d_data *data = i2c_get_clientdata(client); + long val = simple_strtol(buf, NULL, 10); + int nr = attr->index; + + mutex_lock(&data->update_lock); + data->temp1[nr] = TEMP1_TO_REG(val); + w83791d_write(client, W83791D_REG_TEMP1[nr], data->temp1[nr]); + mutex_unlock(&data->update_lock); + return count; +} + +/* read/write temperature2-3, includes measured value and limits */ +static ssize_t show_temp23(struct device *dev, struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); + struct w83791d_data *data = w83791d_update_device(dev); + int nr = attr->nr; + int index = attr->index; + return sprintf(buf, "%d\n", TEMP23_FROM_REG(data->temp_add[nr][index])); +} + +static ssize_t store_temp23(struct device *dev, + struct device_attribute *devattr, + const char *buf, size_t count) +{ + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct w83791d_data *data = i2c_get_clientdata(client); + long val = simple_strtol(buf, NULL, 10); + int nr = attr->nr; + int index = attr->index; + + mutex_lock(&data->update_lock); + data->temp_add[nr][index] = TEMP23_TO_REG(val); + w83791d_write(client, W83791D_REG_TEMP_ADD[nr][index * 2], + data->temp_add[nr][index] >> 8); + w83791d_write(client, W83791D_REG_TEMP_ADD[nr][index * 2 + 1], + data->temp_add[nr][index] & 0x80); + mutex_unlock(&data->update_lock); + + return count; +} + +static struct sensor_device_attribute_2 sda_temp_input[] = { + SENSOR_ATTR_2(temp1_input, S_IRUGO, show_temp1, NULL, 0, 0), + SENSOR_ATTR_2(temp2_input, S_IRUGO, show_temp23, NULL, 0, 0), + SENSOR_ATTR_2(temp3_input, S_IRUGO, show_temp23, NULL, 1, 0), +}; + +static struct sensor_device_attribute_2 sda_temp_max[] = { + SENSOR_ATTR_2(temp1_max, S_IRUGO | S_IWUSR, + show_temp1, store_temp1, 0, 1), + SENSOR_ATTR_2(temp2_max, S_IRUGO | S_IWUSR, + show_temp23, store_temp23, 0, 1), + SENSOR_ATTR_2(temp3_max, S_IRUGO | S_IWUSR, + show_temp23, store_temp23, 1, 1), +}; + +static struct sensor_device_attribute_2 sda_temp_max_hyst[] = { + SENSOR_ATTR_2(temp1_max_hyst, S_IRUGO | S_IWUSR, + show_temp1, store_temp1, 0, 2), + SENSOR_ATTR_2(temp2_max_hyst, S_IRUGO | S_IWUSR, + show_temp23, store_temp23, 0, 2), + SENSOR_ATTR_2(temp3_max_hyst, S_IRUGO | S_IWUSR, + show_temp23, store_temp23, 1, 2), +}; + + +/* get reatime status of all sensors items: voltage, temp, fan */ +static ssize_t show_alarms_reg(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct w83791d_data *data = w83791d_update_device(dev); + return sprintf(buf, "%u\n", data->alarms); +} + +static DEVICE_ATTR(alarms, S_IRUGO, show_alarms_reg, NULL); + +/* Beep control */ + +#define GLOBAL_BEEP_ENABLE_SHIFT 15 +#define GLOBAL_BEEP_ENABLE_MASK (1 << GLOBAL_BEEP_ENABLE_SHIFT) + +static ssize_t show_beep_enable(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct w83791d_data *data = w83791d_update_device(dev); + return sprintf(buf, "%d\n", data->beep_enable); +} + +static ssize_t show_beep_mask(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct w83791d_data *data = w83791d_update_device(dev); + return sprintf(buf, "%d\n", BEEP_MASK_FROM_REG(data->beep_mask)); +} + + +static ssize_t store_beep_mask(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct w83791d_data *data = i2c_get_clientdata(client); + long val = simple_strtol(buf, NULL, 10); + int i; + + mutex_lock(&data->update_lock); + + /* The beep_enable state overrides any enabling request from + the masks */ + data->beep_mask = BEEP_MASK_TO_REG(val) & ~GLOBAL_BEEP_ENABLE_MASK; + data->beep_mask |= (data->beep_enable << GLOBAL_BEEP_ENABLE_SHIFT); + + val = data->beep_mask; + + for (i = 0; i < 3; i++) { + w83791d_write(client, W83791D_REG_BEEP_CTRL[i], (val & 0xff)); + val >>= 8; + } + + mutex_unlock(&data->update_lock); + + return count; +} + +static ssize_t store_beep_enable(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct w83791d_data *data = i2c_get_clientdata(client); + long val = simple_strtol(buf, NULL, 10); + + mutex_lock(&data->update_lock); + + data->beep_enable = val ? 1 : 0; + + /* Keep the full mask value in sync with the current enable */ + data->beep_mask &= ~GLOBAL_BEEP_ENABLE_MASK; + data->beep_mask |= (data->beep_enable << GLOBAL_BEEP_ENABLE_SHIFT); + + /* The global control is in the second beep control register + so only need to update that register */ + val = (data->beep_mask >> 8) & 0xff; + + w83791d_write(client, W83791D_REG_BEEP_CTRL[1], val); + + mutex_unlock(&data->update_lock); + + return count; +} + +static struct sensor_device_attribute sda_beep_ctrl[] = { + SENSOR_ATTR(beep_enable, S_IRUGO | S_IWUSR, + show_beep_enable, store_beep_enable, 0), + SENSOR_ATTR(beep_mask, S_IRUGO | S_IWUSR, + show_beep_mask, store_beep_mask, 1) +}; + +/* cpu voltage regulation information */ +static ssize_t show_vid_reg(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct w83791d_data *data = w83791d_update_device(dev); + return sprintf(buf, "%d\n", vid_from_reg(data->vid, data->vrm)); +} + +static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid_reg, NULL); + +static ssize_t show_vrm_reg(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct w83791d_data *data = w83791d_update_device(dev); + return sprintf(buf, "%d\n", data->vrm); +} + +static ssize_t store_vrm_reg(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct w83791d_data *data = i2c_get_clientdata(client); + unsigned long val = simple_strtoul(buf, NULL, 10); + + /* No lock needed as vrm is internal to the driver + (not read from a chip register) and so is not + updated in w83791d_update_device() */ + data->vrm = val; + + return count; +} + +static DEVICE_ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm_reg, store_vrm_reg); + +/* This function is called when: + * w83791d_driver is inserted (when this module is loaded), for each + available adapter + * when a new adapter is inserted (and w83791d_driver is still present) */ +static int w83791d_attach_adapter(struct i2c_adapter *adapter) +{ + if (!(adapter->class & I2C_CLASS_HWMON)) + return 0; + return i2c_probe(adapter, &addr_data, w83791d_detect); +} + + +static int w83791d_create_subclient(struct i2c_adapter *adapter, + struct i2c_client *client, int addr, + struct i2c_client **sub_cli) +{ + int err; + struct i2c_client *sub_client; + + (*sub_cli) = sub_client = + kzalloc(sizeof(struct i2c_client), GFP_KERNEL); + if (!(sub_client)) { + return -ENOMEM; + } + sub_client->addr = 0x48 + addr; + i2c_set_clientdata(sub_client, NULL); + sub_client->adapter = adapter; + sub_client->driver = &w83791d_driver; + strlcpy(sub_client->name, "w83791d subclient", I2C_NAME_SIZE); + if ((err = i2c_attach_client(sub_client))) { + dev_err(&client->dev, "subclient registration " + "at address 0x%x failed\n", sub_client->addr); + kfree(sub_client); + return err; + } + return 0; +} + + +static int w83791d_detect_subclients(struct i2c_adapter *adapter, int address, + int kind, struct i2c_client *client) +{ + struct w83791d_data *data = i2c_get_clientdata(client); + int i, id, err; + u8 val; + + id = i2c_adapter_id(adapter); + if (force_subclients[0] == id && force_subclients[1] == address) { + for (i = 2; i <= 3; i++) { + if (force_subclients[i] < 0x48 || + force_subclients[i] > 0x4f) { + dev_err(&client->dev, + "invalid subclient " + "address %d; must be 0x48-0x4f\n", + force_subclients[i]); + err = -ENODEV; + goto error_sc_0; + } + } + w83791d_write(client, W83791D_REG_I2C_SUBADDR, + (force_subclients[2] & 0x07) | + ((force_subclients[3] & 0x07) << 4)); + } + + val = w83791d_read(client, W83791D_REG_I2C_SUBADDR); + if (!(val & 0x08)) { + err = w83791d_create_subclient(adapter, client, + val & 0x7, &data->lm75[0]); + if (err < 0) + goto error_sc_0; + } + if (!(val & 0x80)) { + if ((data->lm75[0] != NULL) && + ((val & 0x7) == ((val >> 4) & 0x7))) { + dev_err(&client->dev, + "duplicate addresses 0x%x, " + "use force_subclient\n", + data->lm75[0]->addr); + err = -ENODEV; + goto error_sc_1; + } + err = w83791d_create_subclient(adapter, client, + (val >> 4) & 0x7, &data->lm75[1]); + if (err < 0) + goto error_sc_1; + } + + return 0; + +/* Undo inits in case of errors */ + +error_sc_1: + if (data->lm75[0] != NULL) { + i2c_detach_client(data->lm75[0]); + kfree(data->lm75[0]); + } +error_sc_0: + return err; +} + + +static int w83791d_detect(struct i2c_adapter *adapter, int address, int kind) +{ + struct i2c_client *client; + struct device *dev; + struct w83791d_data *data; + int i, val1, val2; + int err = 0; + const char *client_name = ""; + + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { + goto error0; + } + + /* OK. For now, we presume we have a valid client. We now create the + client structure, even though we cannot fill it completely yet. + But it allows us to access w83791d_{read,write}_value. */ + if (!(data = kzalloc(sizeof(struct w83791d_data), GFP_KERNEL))) { + err = -ENOMEM; + goto error0; + } + + client = &data->client; + dev = &client->dev; + i2c_set_clientdata(client, data); + client->addr = address; + client->adapter = adapter; + client->driver = &w83791d_driver; + mutex_init(&data->update_lock); + + /* Now, we do the remaining detection. */ + + /* The w83791d may be stuck in some other bank than bank 0. This may + make reading other information impossible. Specify a force=... + parameter, and the Winbond will be reset to the right bank. */ + if (kind < 0) { + if (w83791d_read(client, W83791D_REG_CONFIG) & 0x80) { + dev_dbg(dev, "Detection failed at step 1\n"); + goto error1; + } + val1 = w83791d_read(client, W83791D_REG_BANK); + val2 = w83791d_read(client, W83791D_REG_CHIPMAN); + /* Check for Winbond ID if in bank 0 */ + if (!(val1 & 0x07)) { + /* yes it is Bank0 */ + if (((!(val1 & 0x80)) && (val2 != 0xa3)) || + ((val1 & 0x80) && (val2 != 0x5c))) { + dev_dbg(dev, "Detection failed at step 2\n"); + goto error1; + } + } + /* If Winbond chip, address of chip and W83791D_REG_I2C_ADDR + should match */ + if (w83791d_read(client, W83791D_REG_I2C_ADDR) != address) { + dev_dbg(dev, "Detection failed at step 3\n"); + goto error1; + } + } + + /* We either have a force parameter or we have reason to + believe it is a Winbond chip. Either way, we want bank 0 and + Vendor ID high byte */ + val1 = w83791d_read(client, W83791D_REG_BANK) & 0x78; + w83791d_write(client, W83791D_REG_BANK, val1 | 0x80); + + /* Verify it is a Winbond w83791d */ + if (kind <= 0) { + /* get vendor ID */ + val2 = w83791d_read(client, W83791D_REG_CHIPMAN); + if (val2 != 0x5c) { /* the vendor is NOT Winbond */ + dev_dbg(dev, "Detection failed at step 4\n"); + goto error1; + } + val1 = w83791d_read(client, W83791D_REG_WCHIPID); + if (val1 == 0x71) { + kind = w83791d; + } else { + if (kind == 0) + dev_warn(dev, + "w83791d: Ignoring 'force' parameter " + "for unknown chip at adapter %d, " + "address 0x%02x\n", + i2c_adapter_id(adapter), address); + goto error1; + } + } + + if (kind == w83791d) { + client_name = "w83791d"; + } else { + dev_err(dev, "w83791d: Internal error: unknown kind (%d)?!?", + kind); + goto error1; + } + +#ifdef DEBUG + val1 = w83791d_read(client, W83791D_REG_DID_VID4); + dev_dbg(dev, "Device ID version: %d.%d (0x%02x)\n", + (val1 >> 5) & 0x07, (val1 >> 1) & 0x0f, val1); +#endif + + /* Fill in the remaining client fields and put into the global list */ + strlcpy(client->name, client_name, I2C_NAME_SIZE); + + /* Tell the I2C layer a new client has arrived */ + if ((err = i2c_attach_client(client))) + goto error1; + + if ((err = w83791d_detect_subclients(adapter, address, kind, client))) + goto error2; + + /* Initialize the chip */ + w83791d_init_client(client); + + /* If the fan_div is changed, make sure there is a rational + fan_min in place */ + for (i = 0; i < NUMBER_OF_FANIN; i++) { + data->fan_min[i] = w83791d_read(client, W83791D_REG_FAN_MIN[i]); + } + + /* Register sysfs hooks */ + data->class_dev = hwmon_device_register(dev); + if (IS_ERR(data->class_dev)) { + err = PTR_ERR(data->class_dev); + goto error3; + } + + for (i = 0; i < NUMBER_OF_VIN; i++) { + device_create_file(dev, &sda_in_input[i].dev_attr); + device_create_file(dev, &sda_in_min[i].dev_attr); + device_create_file(dev, &sda_in_max[i].dev_attr); + } + + for (i = 0; i < NUMBER_OF_FANIN; i++) { + device_create_file(dev, &sda_fan_input[i].dev_attr); + device_create_file(dev, &sda_fan_div[i].dev_attr); + device_create_file(dev, &sda_fan_min[i].dev_attr); + } + + for (i = 0; i < NUMBER_OF_TEMPIN; i++) { + device_create_file(dev, &sda_temp_input[i].dev_attr); + device_create_file(dev, &sda_temp_max[i].dev_attr); + device_create_file(dev, &sda_temp_max_hyst[i].dev_attr); + } + + device_create_file(dev, &dev_attr_alarms); + + for (i = 0; i < ARRAY_SIZE(sda_beep_ctrl); i++) { + device_create_file(dev, &sda_beep_ctrl[i].dev_attr); + } + + device_create_file(dev, &dev_attr_cpu0_vid); + device_create_file(dev, &dev_attr_vrm); + + return 0; + +error3: + if (data->lm75[0] != NULL) { + i2c_detach_client(data->lm75[0]); + kfree(data->lm75[0]); + } + if (data->lm75[1] != NULL) { + i2c_detach_client(data->lm75[1]); + kfree(data->lm75[1]); + } +error2: + i2c_detach_client(client); +error1: + kfree(data); +error0: + return err; +} + +static int w83791d_detach_client(struct i2c_client *client) +{ + struct w83791d_data *data = i2c_get_clientdata(client); + int err; + + /* main client */ + if (data) + hwmon_device_unregister(data->class_dev); + + if ((err = i2c_detach_client(client))) + return err; + + /* main client */ + if (data) + kfree(data); + /* subclient */ + else + kfree(client); + + return 0; +} + +static void w83791d_init_client(struct i2c_client *client) +{ + struct w83791d_data *data = i2c_get_clientdata(client); + u8 tmp; + u8 old_beep; + + /* The difference between reset and init is that reset + does a hard reset of the chip via index 0x40, bit 7, + but init simply forces certain registers to have "sane" + values. The hope is that the BIOS has done the right + thing (which is why the default is reset=0, init=0), + but if not, reset is the hard hammer and init + is the soft mallet both of which are trying to whack + things into place... + NOTE: The data sheet makes a distinction between + "power on defaults" and "reset by MR". As far as I can tell, + the hard reset puts everything into a power-on state so I'm + not sure what "reset by MR" means or how it can happen. + */ + if (reset || init) { + /* keep some BIOS settings when we... */ + old_beep = w83791d_read(client, W83791D_REG_BEEP_CONFIG); + + if (reset) { + /* ... reset the chip and ... */ + w83791d_write(client, W83791D_REG_CONFIG, 0x80); + } + + /* ... disable power-on abnormal beep */ + w83791d_write(client, W83791D_REG_BEEP_CONFIG, old_beep | 0x80); + + /* disable the global beep (not done by hard reset) */ + tmp = w83791d_read(client, W83791D_REG_BEEP_CTRL[1]); + w83791d_write(client, W83791D_REG_BEEP_CTRL[1], tmp & 0xef); + + if (init) { + /* Make sure monitoring is turned on for add-ons */ + tmp = w83791d_read(client, W83791D_REG_TEMP2_CONFIG); + if (tmp & 1) { + w83791d_write(client, W83791D_REG_TEMP2_CONFIG, + tmp & 0xfe); + } + + tmp = w83791d_read(client, W83791D_REG_TEMP3_CONFIG); + if (tmp & 1) { + w83791d_write(client, W83791D_REG_TEMP3_CONFIG, + tmp & 0xfe); + } + + /* Start monitoring */ + tmp = w83791d_read(client, W83791D_REG_CONFIG) & 0xf7; + w83791d_write(client, W83791D_REG_CONFIG, tmp | 0x01); + } + } + + data->vrm = vid_which_vrm(); +} + +static struct w83791d_data *w83791d_update_device(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct w83791d_data *data = i2c_get_clientdata(client); + int i, j; + u8 reg_array_tmp[3]; + + mutex_lock(&data->update_lock); + + if (time_after(jiffies, data->last_updated + (HZ * 3)) + || !data->valid) { + dev_dbg(dev, "Starting w83791d device update\n"); + + /* Update the voltages measured value and limits */ + for (i = 0; i < NUMBER_OF_VIN; i++) { + data->in[i] = w83791d_read(client, + W83791D_REG_IN[i]); + data->in_max[i] = w83791d_read(client, + W83791D_REG_IN_MAX[i]); + data->in_min[i] = w83791d_read(client, + W83791D_REG_IN_MIN[i]); + } + + /* Update the fan counts and limits */ + for (i = 0; i < NUMBER_OF_FANIN; i++) { + /* Update the Fan measured value and limits */ + data->fan[i] = w83791d_read(client, + W83791D_REG_FAN[i]); + data->fan_min[i] = w83791d_read(client, + W83791D_REG_FAN_MIN[i]); + } + + /* Update the fan divisor */ + for (i = 0; i < 3; i++) { + reg_array_tmp[i] = w83791d_read(client, + W83791D_REG_FAN_DIV[i]); + } + data->fan_div[0] = (reg_array_tmp[0] >> 4) & 0x03; + data->fan_div[1] = (reg_array_tmp[0] >> 6) & 0x03; + data->fan_div[2] = (reg_array_tmp[1] >> 6) & 0x03; + data->fan_div[3] = reg_array_tmp[2] & 0x07; + data->fan_div[4] = (reg_array_tmp[2] >> 4) & 0x07; + + /* Update the first temperature sensor */ + for (i = 0; i < 3; i++) { + data->temp1[i] = w83791d_read(client, + W83791D_REG_TEMP1[i]); + } + + /* Update the rest of the temperature sensors */ + for (i = 0; i < 2; i++) { + for (j = 0; j < 3; j++) { + data->temp_add[i][j] = + (w83791d_read(client, + W83791D_REG_TEMP_ADD[i][j * 2]) << 8) | + w83791d_read(client, + W83791D_REG_TEMP_ADD[i][j * 2 + 1]); + } + } + + /* Update the realtime status */ + data->alarms = + w83791d_read(client, W83791D_REG_ALARM1) + + (w83791d_read(client, W83791D_REG_ALARM2) << 8) + + (w83791d_read(client, W83791D_REG_ALARM3) << 16); + + /* Update the beep configuration information */ + data->beep_mask = + w83791d_read(client, W83791D_REG_BEEP_CTRL[0]) + + (w83791d_read(client, W83791D_REG_BEEP_CTRL[1]) << 8) + + (w83791d_read(client, W83791D_REG_BEEP_CTRL[2]) << 16); + + data->beep_enable = + (data->beep_mask >> GLOBAL_BEEP_ENABLE_SHIFT) & 0x01; + + /* Update the cpu voltage information */ + i = w83791d_read(client, W83791D_REG_VID_FANDIV); + data->vid = i & 0x0f; + data->vid |= (w83791d_read(client, W83791D_REG_DID_VID4) & 0x01) + << 4; + + data->last_updated = jiffies; + data->valid = 1; + } + + mutex_unlock(&data->update_lock); + +#ifdef DEBUG + w83791d_print_debug(data, dev); +#endif + + return data; +} + +#ifdef DEBUG +static void w83791d_print_debug(struct w83791d_data *data, struct device *dev) +{ + int i = 0, j = 0; + + dev_dbg(dev, "======Start of w83791d debug values======\n"); + dev_dbg(dev, "%d set of Voltages: ===>\n", NUMBER_OF_VIN); + for (i = 0; i < NUMBER_OF_VIN; i++) { + dev_dbg(dev, "vin[%d] is: 0x%02x\n", i, data->in[i]); + dev_dbg(dev, "vin[%d] min is: 0x%02x\n", i, data->in_min[i]); + dev_dbg(dev, "vin[%d] max is: 0x%02x\n", i, data->in_max[i]); + } + dev_dbg(dev, "%d set of Fan Counts/Divisors: ===>\n", NUMBER_OF_FANIN); + for (i = 0; i < NUMBER_OF_FANIN; i++) { + dev_dbg(dev, "fan[%d] is: 0x%02x\n", i, data->fan[i]); + dev_dbg(dev, "fan[%d] min is: 0x%02x\n", i, data->fan_min[i]); + dev_dbg(dev, "fan_div[%d] is: 0x%02x\n", i, data->fan_div[i]); + } + + /* temperature math is signed, but only print out the + bits that matter */ + dev_dbg(dev, "%d set of Temperatures: ===>\n", NUMBER_OF_TEMPIN); + for (i = 0; i < 3; i++) { + dev_dbg(dev, "temp1[%d] is: 0x%02x\n", i, (u8) data->temp1[i]); + } + for (i = 0; i < 2; i++) { + for (j = 0; j < 3; j++) { + dev_dbg(dev, "temp_add[%d][%d] is: 0x%04x\n", i, j, + (u16) data->temp_add[i][j]); + } + } + + dev_dbg(dev, "Misc Information: ===>\n"); + dev_dbg(dev, "alarm is: 0x%08x\n", data->alarms); + dev_dbg(dev, "beep_mask is: 0x%08x\n", data->beep_mask); + dev_dbg(dev, "beep_enable is: %d\n", data->beep_enable); + dev_dbg(dev, "vid is: 0x%02x\n", data->vid); + dev_dbg(dev, "vrm is: 0x%02x\n", data->vrm); + dev_dbg(dev, "=======End of w83791d debug values========\n"); + dev_dbg(dev, "\n"); +} +#endif + +static int __init sensors_w83791d_init(void) +{ + return i2c_add_driver(&w83791d_driver); +} + +static void __exit sensors_w83791d_exit(void) +{ + i2c_del_driver(&w83791d_driver); +} + +MODULE_AUTHOR("Charles Spirakis <bezaur@gmail.com>"); +MODULE_DESCRIPTION("W83791D driver"); +MODULE_LICENSE("GPL"); + +module_init(sensors_w83791d_init); +module_exit(sensors_w83791d_exit); |
