summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
Diffstat
-rw-r--r--drivers/tty/serial/8250/8250.c71
-rw-r--r--drivers/tty/serial/8250/8250_pci.c96
-rw-r--r--include/linux/pci_ids.h3
-rw-r--r--include/uapi/linux/serial_core.h3
-rw-r--r--include/uapi/linux/serial_reg.h6
5 files changed, 178 insertions, 1 deletions
diff --git a/drivers/tty/serial/8250/8250.c b/drivers/tty/serial/8250/8250.c
index 2af83a246499..3624df674a31 100644
--- a/drivers/tty/serial/8250/8250.c
+++ b/drivers/tty/serial/8250/8250.c
@@ -282,6 +282,15 @@ static const struct serial8250_config uart_config[] = {
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR,
},
+ [PORT_XR17V35X] = {
+ .name = "XR17V35X",
+ .fifo_size = 256,
+ .tx_loadsz = 256,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11 |
+ UART_FCR_T_TRIG_11,
+ .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR |
+ UART_CAP_SLEEP,
+ },
[PORT_LPC3220] = {
.name = "LPC3220",
.fifo_size = 64,
@@ -455,6 +464,7 @@ static void io_serial_out(struct uart_port *p, int offset, int value)
}
static int serial8250_default_handle_irq(struct uart_port *port);
+static int exar_handle_irq(struct uart_port *port);
static void set_io_from_upio(struct uart_port *p)
{
@@ -574,6 +584,18 @@ EXPORT_SYMBOL_GPL(serial8250_clear_and_reinit_fifos);
*/
static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
{
+ /*
+ * Exar UARTs have a SLEEP register that enables or disables
+ * each UART to enter sleep mode separately. On the XR17V35x the
+ * register is accessible to each UART at the UART_EXAR_SLEEP
+ * offset but the UART channel may only write to the corresponding
+ * bit.
+ */
+ if (p->port.type == PORT_XR17V35X) {
+ serial_out(p, UART_EXAR_SLEEP, 0xff);
+ return;
+ }
+
if (p->capabilities & UART_CAP_SLEEP) {
if (p->capabilities & UART_CAP_EFR) {
serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B);
@@ -882,6 +904,27 @@ static void autoconfig_16550a(struct uart_8250_port *up)
up->capabilities |= UART_CAP_FIFO;
/*
+ * XR17V35x UARTs have an extra divisor register, DLD
+ * that gets enabled with when DLAB is set which will
+ * cause the device to incorrectly match and assign
+ * port type to PORT_16650. The EFR for this UART is
+ * found at offset 0x09. Instead check the Deice ID (DVID)
+ * register for a 2, 4 or 8 port UART.
+ */
+ status1 = serial_in(up, UART_EXAR_DVID);
+ if (status1 == 0x82 || status1 == 0x84 || status1 == 0x88) {
+ if (up->port.flags & UPF_EXAR_EFR) {
+ DEBUG_AUTOCONF("Exar XR17V35x ");
+ up->port.type = PORT_XR17V35X;
+ up->capabilities |= UART_CAP_AFE | UART_CAP_EFR |
+ UART_CAP_SLEEP;
+
+ return;
+ }
+
+ }
+
+ /*
* Check for presence of the EFR when DLAB is set.
* Only ST16C650V1 UARTs pass this test.
*/
@@ -1516,6 +1559,30 @@ static int serial8250_default_handle_irq(struct uart_port *port)
}
/*
+ * These Exar UARTs have an extra interrupt indicator that could
+ * fire for a few unimplemented interrupts. One of which is a
+ * wakeup event when coming out of sleep. Put this here just
+ * to be on the safe side that these interrupts don't go unhandled.
+ */
+static int exar_handle_irq(struct uart_port *port)
+{
+ unsigned char int0, int1, int2, int3;
+ unsigned int iir = serial_port_in(port, UART_IIR);
+ int ret;
+
+ ret = serial8250_handle_irq(port, iir);
+
+ if (port->type == PORT_XR17V35X) {
+ int0 = serial_port_in(port, 0x80);
+ int1 = serial_port_in(port, 0x81);
+ int2 = serial_port_in(port, 0x82);
+ int3 = serial_port_in(port, 0x83);
+ }
+
+ return ret;
+}
+
+/*
* This is the serial driver's interrupt routine.
*
* Arjan thinks the old way was overly complex, so it got simplified.
@@ -2614,6 +2681,10 @@ static void serial8250_config_port(struct uart_port *port, int flags)
serial8250_release_rsa_resource(up);
if (port->type == PORT_UNKNOWN)
serial8250_release_std_resource(up);
+
+ /* Fixme: probably not the best place for this */
+ if (port->type == PORT_XR17V35X)
+ port->handle_irq = exar_handle_irq;
}
static int
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 97058c1d7d45..2285d3283b3b 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1165,6 +1165,39 @@ pci_xr17c154_setup(struct serial_private *priv,
}
static int
+pci_xr17v35x_setup(struct serial_private *priv,
+ const struct pciserial_board *board,
+ struct uart_8250_port *port, int idx)
+{
+ u8 __iomem *p;
+
+ p = pci_ioremap_bar(priv->dev, 0);
+
+ port->port.flags |= UPF_EXAR_EFR;
+
+ /*
+ * Setup Multipurpose Input/Output pins.
+ */
+ if (idx == 0) {
+ writeb(0x00, p + 0x8f); /*MPIOINT[7:0]*/
+ writeb(0x00, p + 0x90); /*MPIOLVL[7:0]*/
+ writeb(0x00, p + 0x91); /*MPIO3T[7:0]*/
+ writeb(0x00, p + 0x92); /*MPIOINV[7:0]*/
+ writeb(0x00, p + 0x93); /*MPIOSEL[7:0]*/
+ writeb(0x00, p + 0x94); /*MPIOOD[7:0]*/
+ writeb(0x00, p + 0x95); /*MPIOINT[15:8]*/
+ writeb(0x00, p + 0x96); /*MPIOLVL[15:8]*/
+ writeb(0x00, p + 0x97); /*MPIO3T[15:8]*/
+ writeb(0x00, p + 0x98); /*MPIOINV[15:8]*/
+ writeb(0x00, p + 0x99); /*MPIOSEL[15:8]*/
+ writeb(0x00, p + 0x9a); /*MPIOOD[15:8]*/
+ }
+ iounmap(p);
+
+ return pci_default_setup(priv, board, port, idx);
+}
+
+static int
pci_wch_ch353_setup(struct serial_private *priv,
const struct pciserial_board *board,
struct uart_8250_port *port, int idx)
@@ -1622,6 +1655,27 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
.subdevice = PCI_ANY_ID,
.setup = pci_xr17c154_setup,
},
+ {
+ .vendor = PCI_VENDOR_ID_EXAR,
+ .device = PCI_DEVICE_ID_EXAR_XR17V352,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_xr17v35x_setup,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_EXAR,
+ .device = PCI_DEVICE_ID_EXAR_XR17V354,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_xr17v35x_setup,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_EXAR,
+ .device = PCI_DEVICE_ID_EXAR_XR17V358,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_xr17v35x_setup,
+ },
/*
* Xircom cards
*/
@@ -1962,6 +2016,9 @@ enum pci_board_num_t {
pbn_exar_XR17C152,
pbn_exar_XR17C154,
pbn_exar_XR17C158,
+ pbn_exar_XR17V352,
+ pbn_exar_XR17V354,
+ pbn_exar_XR17V358,
pbn_exar_ibm_saturn,
pbn_pasemi_1682M,
pbn_ni8430_2,
@@ -2580,6 +2637,30 @@ static struct pciserial_board pci_boards[] = {
.base_baud = 921600,
.uart_offset = 0x200,
},
+ [pbn_exar_XR17V352] = {
+ .flags = FL_BASE0,
+ .num_ports = 2,
+ .base_baud = 7812500,
+ .uart_offset = 0x400,
+ .reg_shift = 0,
+ .first_offset = 0,
+ },
+ [pbn_exar_XR17V354] = {
+ .flags = FL_BASE0,
+ .num_ports = 4,
+ .base_baud = 7812500,
+ .uart_offset = 0x400,
+ .reg_shift = 0,
+ .first_offset = 0,
+ },
+ [pbn_exar_XR17V358] = {
+ .flags = FL_BASE0,
+ .num_ports = 8,
+ .base_baud = 7812500,
+ .uart_offset = 0x400,
+ .reg_shift = 0,
+ .first_offset = 0,
+ },
[pbn_exar_ibm_saturn] = {
.flags = FL_BASE0,
.num_ports = 1,
@@ -3826,6 +3907,21 @@ static struct pci_device_id serial_pci_tbl[] = {
PCI_ANY_ID, PCI_ANY_ID,
0,
0, pbn_exar_XR17C158 },
+ /*
+ * Exar Corp. XR17V35[248] Dual/Quad/Octal PCIe UARTs
+ */
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V352,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_exar_XR17V352 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V354,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_exar_XR17V354 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V358,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_exar_XR17V358 },
/*
* Topic TP560 Data/Fax/Voice 56k modem (reported by Evan Clarke)
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index 9d36b829533a..0199a7a76fcb 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -1985,6 +1985,9 @@
#define PCI_DEVICE_ID_EXAR_XR17C152 0x0152
#define PCI_DEVICE_ID_EXAR_XR17C154 0x0154
#define PCI_DEVICE_ID_EXAR_XR17C158 0x0158
+#define PCI_DEVICE_ID_EXAR_XR17V352 0x0352
+#define PCI_DEVICE_ID_EXAR_XR17V354 0x0354
+#define PCI_DEVICE_ID_EXAR_XR17V358 0x0358
#define PCI_VENDOR_ID_MICROGATE 0x13c0
#define PCI_DEVICE_ID_MICROGATE_USC 0x0010
diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
index ebcc73f0418a..78f99d97475b 100644
--- a/include/uapi/linux/serial_core.h
+++ b/include/uapi/linux/serial_core.h
@@ -49,7 +49,8 @@
#define PORT_XR17D15X 21 /* Exar XR17D15x UART */
#define PORT_LPC3220 22 /* NXP LPC32xx SoC "Standard" UART */
#define PORT_8250_CIR 23 /* CIR infrared port, has its own driver */
-#define PORT_MAX_8250 23 /* max port ID */
+#define PORT_XR17V35X 24 /* Exar XR17V35x UARTs */
+#define PORT_MAX_8250 24 /* max port ID */
/*
* ARM specific type numbers. These are not currently guaranteed
diff --git a/include/uapi/linux/serial_reg.h b/include/uapi/linux/serial_reg.h
index 5ed325e88a81..d0b47607b90b 100644
--- a/include/uapi/linux/serial_reg.h
+++ b/include/uapi/linux/serial_reg.h
@@ -367,5 +367,11 @@
#define UART_OMAP_MDR1_CIR_MODE 0x06 /* CIR mode */
#define UART_OMAP_MDR1_DISABLE 0x07 /* Disable (default state) */
+/*
+ * These are definitions for the XR17V35X and XR17D15X
+ */
+#define UART_EXAR_SLEEP 0x8b /* Sleep mode */
+#define UART_EXAR_DVID 0x8d /* Device identification */
+
#endif /* _LINUX_SERIAL_REG_H */
OpenPOWER on IntegriCloud