diff options
130 files changed, 15264 insertions, 1950 deletions
diff --git a/Documentation/usb/power-management.txt b/Documentation/usb/power-management.txt index b29d8e56cf28..c9ffa9ced7ee 100644 --- a/Documentation/usb/power-management.txt +++ b/Documentation/usb/power-management.txt @@ -2,7 +2,7 @@ Alan Stern <stern@rowland.harvard.edu> - December 11, 2009 + October 28, 2010 @@ -107,9 +107,14 @@ allowed to issue dynamic suspends. The user interface for controlling dynamic PM is located in the power/ subdirectory of each USB device's sysfs directory, that is, in /sys/bus/usb/devices/.../power/ where "..." is the device's ID. The -relevant attribute files are: wakeup, control, and autosuspend. -(There may also be a file named "level"; this file was deprecated -as of the 2.6.35 kernel and replaced by the "control" file.) +relevant attribute files are: wakeup, control, and +autosuspend_delay_ms. (There may also be a file named "level"; this +file was deprecated as of the 2.6.35 kernel and replaced by the +"control" file. In 2.6.38 the "autosuspend" file will be deprecated +and replaced by the "autosuspend_delay_ms" file. The only difference +is that the newer file expresses the delay in milliseconds whereas the +older file uses seconds. Confusingly, both files are present in 2.6.37 +but only "autosuspend" works.) power/wakeup @@ -140,33 +145,36 @@ as of the 2.6.35 kernel and replaced by the "control" file.) suspended and autoresume was not allowed. This setting is no longer supported.) - power/autosuspend + power/autosuspend_delay_ms This file contains an integer value, which is the - number of seconds the device should remain idle before - the kernel will autosuspend it (the idle-delay time). - The default is 2. 0 means to autosuspend as soon as - the device becomes idle, and negative values mean - never to autosuspend. You can write a number to the - file to change the autosuspend idle-delay time. - -Writing "-1" to power/autosuspend and writing "on" to power/control do -essentially the same thing -- they both prevent the device from being -autosuspended. Yes, this is a redundancy in the API. + number of milliseconds the device should remain idle + before the kernel will autosuspend it (the idle-delay + time). The default is 2000. 0 means to autosuspend + as soon as the device becomes idle, and negative + values mean never to autosuspend. You can write a + number to the file to change the autosuspend + idle-delay time. + +Writing "-1" to power/autosuspend_delay_ms and writing "on" to +power/control do essentially the same thing -- they both prevent the +device from being autosuspended. Yes, this is a redundancy in the +API. (In 2.6.21 writing "0" to power/autosuspend would prevent the device from being autosuspended; the behavior was changed in 2.6.22. The power/autosuspend attribute did not exist prior to 2.6.21, and the power/level attribute did not exist prior to 2.6.22. power/control -was added in 2.6.34.) +was added in 2.6.34, and power/autosuspend_delay_ms was added in +2.6.37 but did not become functional until 2.6.38.) Changing the default idle-delay time ------------------------------------ -The default autosuspend idle-delay time is controlled by a module -parameter in usbcore. You can specify the value when usbcore is -loaded. For example, to set it to 5 seconds instead of 2 you would +The default autosuspend idle-delay time (in seconds) is controlled by +a module parameter in usbcore. You can specify the value when usbcore +is loaded. For example, to set it to 5 seconds instead of 2 you would do: modprobe usbcore autosuspend=5 @@ -234,25 +242,23 @@ every device. If a driver knows that its device has proper suspend/resume support, it can enable autosuspend all by itself. For example, the video -driver for a laptop's webcam might do this, since these devices are -rarely used and so should normally be autosuspended. +driver for a laptop's webcam might do this (in recent kernels they +do), since these devices are rarely used and so should normally be +autosuspended. Sometimes it turns out that even when a device does work okay with -autosuspend there are still problems. For example, there are -experimental patches adding autosuspend support to the usbhid driver, -which manages keyboards and mice, among other things. Tests with a -number of keyboards showed that typing on a suspended keyboard, while -causing the keyboard to do a remote wakeup all right, would -nonetheless frequently result in lost keystrokes. Tests with mice -showed that some of them would issue a remote-wakeup request in -response to button presses but not to motion, and some in response to -neither. +autosuspend there are still problems. For example, the usbhid driver, +which manages keyboards and mice, has autosuspend support. Tests with +a number of keyboards show that typing on a suspended keyboard, while +causing the keyboard to do a remote wakeup all right, will nonetheless +frequently result in lost keystrokes. Tests with mice show that some +of them will issue a remote-wakeup request in response to button +presses but not to motion, and some in response to neither. The kernel will not prevent you from enabling autosuspend on devices that can't handle it. It is even possible in theory to damage a -device by suspending it at the wrong time -- for example, suspending a -USB hard disk might cause it to spin down without parking the heads. -(Highly unlikely, but possible.) Take care. +device by suspending it at the wrong time. (Highly unlikely, but +possible.) Take care. The driver interface for Power Management @@ -336,10 +342,6 @@ autosuspend the interface's device. When the usage counter is = 0 then the interface is considered to be idle, and the kernel may autosuspend the device. -(There is a similar usage counter field in struct usb_device, -associated with the device itself rather than any of its interfaces. -This counter is used only by the USB core.) - Drivers need not be concerned about balancing changes to the usage counter; the USB core will undo any remaining "get"s when a driver is unbound from its interface. As a corollary, drivers must not call @@ -409,11 +411,11 @@ during autosuspend. For example, there's not much point autosuspending a keyboard if the user can't cause the keyboard to do a remote wakeup by typing on it. If the driver sets intf->needs_remote_wakeup to 1, the kernel won't autosuspend the -device if remote wakeup isn't available or has been disabled through -the power/wakeup attribute. (If the device is already autosuspended, -though, setting this flag won't cause the kernel to autoresume it. -Normally a driver would set this flag in its probe method, at which -time the device is guaranteed not to be autosuspended.) +device if remote wakeup isn't available. (If the device is already +autosuspended, though, setting this flag won't cause the kernel to +autoresume it. Normally a driver would set this flag in its probe +method, at which time the device is guaranteed not to be +autosuspended.) If a driver does its I/O asynchronously in interrupt context, it should call usb_autopm_get_interface_async() before starting output and @@ -422,20 +424,19 @@ it receives an input event, it should call usb_mark_last_busy(struct usb_device *udev); -in the event handler. This sets udev->last_busy to the current time. -udev->last_busy is the field used for idle-delay calculations; -updating it will cause any pending autosuspend to be moved back. Most -of the usb_autopm_* routines will also set the last_busy field to the -current time. +in the event handler. This tells the PM core that the device was just +busy and therefore the next autosuspend idle-delay expiration should +be pushed back. Many of the usb_autopm_* routines also make this call, +so drivers need to worry only when interrupt-driven input arrives. Asynchronous operation is always subject to races. For example, a -driver may call one of the usb_autopm_*_interface_async() routines at -a time when the core has just finished deciding the device has been -idle for long enough but not yet gotten around to calling the driver's -suspend method. The suspend method must be responsible for -synchronizing with the output request routine and the URB completion -handler; it should cause autosuspends to fail with -EBUSY if the -driver needs to use the device. +driver may call the usb_autopm_get_interface_async() routine at a time +when the core has just finished deciding the device has been idle for +long enough but not yet gotten around to calling the driver's suspend +method. The suspend method must be responsible for synchronizing with +the I/O request routine and the URB completion handler; it should +cause autosuspends to fail with -EBUSY if the driver needs to use the +device. External suspend calls should never be allowed to fail in this way, only autosuspend calls. The driver can tell them apart by checking @@ -472,7 +473,9 @@ Firstly, a device may already be autosuspended when a system suspend occurs. Since system suspends are supposed to be as transparent as possible, the device should remain suspended following the system resume. But this theory may not work out well in practice; over time -the kernel's behavior in this regard has changed. +the kernel's behavior in this regard has changed. As of 2.6.37 the +policy is to resume all devices during a system resume and let them +handle their own runtime suspends afterward. Secondly, a dynamic power-management event may occur as a system suspend is underway. The window for this is short, since system diff --git a/arch/arm/mach-davinci/usb.c b/arch/arm/mach-davinci/usb.c index 31f0cbea0caa..23d2b6d9fa63 100644 --- a/arch/arm/mach-davinci/usb.c +++ b/arch/arm/mach-davinci/usb.c @@ -64,17 +64,19 @@ static struct resource usb_resources[] = { { .start = IRQ_USBINT, .flags = IORESOURCE_IRQ, + .name = "mc" }, { /* placeholder for the dedicated CPPI IRQ */ .flags = IORESOURCE_IRQ, + .name = "dma" }, }; static u64 usb_dmamask = DMA_BIT_MASK(32); static struct platform_device usb_dev = { - .name = "musb_hdrc", + .name = "musb-davinci", .id = -1, .dev = { .platform_data = &usb_data, @@ -110,6 +112,7 @@ static struct resource da8xx_usb20_resources[] = { { .start = IRQ_DA8XX_USB_INT, .flags = IORESOURCE_IRQ, + .name = "mc", }, }; @@ -121,6 +124,7 @@ int __init da8xx_register_usb20(unsigned mA, unsigned potpgt) usb_dev.resource = da8xx_usb20_resources; usb_dev.num_resources = ARRAY_SIZE(da8xx_usb20_resources); + usb_dev.name = "musb-da8xx"; return platform_device_register(&usb_dev); } diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index ab784bfde908..766727c4031d 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -44,6 +44,7 @@ config ARCH_OMAP4 select ARM_GIC select PL310_ERRATA_588369 select ARM_ERRATA_720789 + select USB_ARCH_HAS_EHCI comment "OMAP Core Type" depends on ARCH_OMAP2 diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 60e51bcf53bd..194863680fe0 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -168,9 +168,11 @@ obj-$(CONFIG_MACH_IGEP0030) += board-igep0030.o \ obj-$(CONFIG_MACH_OMAP3_TOUCHBOOK) += board-omap3touchbook.o \ hsmmc.o obj-$(CONFIG_MACH_OMAP_4430SDP) += board-4430sdp.o \ - hsmmc.o + hsmmc.o \ + omap_phy_internal.o obj-$(CONFIG_MACH_OMAP4_PANDA) += board-omap4panda.o \ - hsmmc.o + hsmmc.o \ + omap_phy_internal.o obj-$(CONFIG_MACH_OMAP3517EVM) += board-am3517evm.o diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c index df5a425a49d1..5aef69521e36 100644 --- a/arch/arm/mach-omap2/board-4430sdp.c +++ b/arch/arm/mach-omap2/board-4430sdp.c @@ -42,6 +42,7 @@ #define ETH_KS8851_IRQ 34 #define ETH_KS8851_POWER_ON 48 #define ETH_KS8851_QUART 138 +#define OMAP4SDP_MDM_PWR_EN_GPIO 157 #define OMAP4_SFH7741_SENSOR_OUTPUT_GPIO 184 #define OMAP4_SFH7741_ENABLE_GPIO 188 @@ -225,12 +226,29 @@ static void __init omap_4430sdp_init_irq(void) omap_gpio_init(); } +static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = { + .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY, + .port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN, + .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN, + .phy_reset = false, + .reset_gpio_port[0] = -EINVAL, + .reset_gpio_port[1] = -EINVAL, + .reset_gpio_port[2] = -EINVAL, +}; + static struct omap_musb_board_data musb_board_data = { .interface_type = MUSB_INTERFACE_UTMI, - .mode = MUSB_PERIPHERAL, + .mode = MUSB_OTG, .power = 100, }; +static struct twl4030_usb_data omap4_usbphy_data = { + .phy_init = omap4430_phy_init, + .phy_exit = omap4430_phy_exit, + .phy_power = omap4430_phy_power, + .phy_set_clock = omap4430_phy_set_clk, +}; + static struct omap2_hsmmc_info mmc[] = { { .mmc = 1, @@ -450,6 +468,7 @@ static struct twl4030_platform_data sdp4430_twldata = { .vaux1 = &sdp4430_vaux1, .vaux2 = &sdp4430_vaux2, .vaux3 = &sdp4430_vaux3, + .usb = &omap4_usbphy_data }; static struct i2c_board_info __initdata sdp4430_i2c_boardinfo[] = { @@ -514,11 +533,15 @@ static void __init omap_4430sdp_init(void) platform_add_devices(sdp4430_devices, ARRAY_SIZE(sdp4430_devices)); omap_serial_init(); omap4_twl6030_hsmmc_init(mmc); - /* OMAP4 SDP uses internal transceiver so register nop transceiver */ - usb_nop_xceiv_register(); - /* FIXME: allow multi-omap to boot until musb is updated for omap4 */ - if (!cpu_is_omap44xx()) - usb_musb_init(&musb_board_data); + + /* Power on the ULPI PHY */ + if (gpio_is_valid(OMAP4SDP_MDM_PWR_EN_GPIO)) { + /* FIXME: Assumes pad is already muxed for GPIO mode */ + gpio_request(OMAP4SDP_MDM_PWR_EN_GPIO, "USBB1 PHY VMDM_3V3"); + gpio_direction_output(OMAP4SDP_MDM_PWR_EN_GPIO, 1); + } + usb_ehci_init(&ehci_pdata); + usb_musb_init(&musb_board_data); status = omap_ethernet_init(); if (status) { diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c index e823c7042ab3..62e3ea007c76 100644 --- a/arch/arm/mach-omap2/board-n8x0.c +++ b/arch/arm/mach-omap2/board-n8x0.c @@ -46,8 +46,7 @@ static struct device *mmc_device; #define TUSB6010_GPIO_ENABLE 0 #define TUSB6010_DMACHAN 0x3f -#if defined(CONFIG_USB_TUSB6010) || \ - defined(CONFIG_USB_TUSB6010_MODULE) +#ifdef CONFIG_USB_MUSB_TUSB6010 /* * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and * 1.5 V voltage regulators of PM companion chip. Companion chip will then @@ -134,7 +133,7 @@ err: static void __init n8x0_usb_init(void) {} -#endif /*CONFIG_USB_TUSB6010 */ +#endif /*CONFIG_USB_MUSB_TUSB6010 */ static struct omap2_mcspi_device_config p54spi_mcspi_config = { diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c index 1ecd0a6cefb7..9207c5849c0e 100644 --- a/arch/arm/mach-omap2/board-omap4panda.c +++ b/arch/arm/mach-omap2/board-omap4panda.c @@ -133,10 +133,17 @@ error1: static struct omap_musb_board_data musb_board_data = { .interface_type = MUSB_INTERFACE_UTMI, - .mode = MUSB_PERIPHERAL, + .mode = MUSB_OTG, .power = 100, }; +static struct twl4030_usb_data omap4_usbphy_data = { + .phy_init = omap4430_phy_init, + .phy_exit = omap4430_phy_exit, + .phy_power = omap4430_phy_power, + .phy_set_clock = omap4430_phy_set_clk, +}; + static struct omap2_hsmmc_info mmc[] = { { .mmc = 1, @@ -345,6 +352,7 @@ static struct twl4030_platform_data omap4_panda_twldata = { .vaux1 = &omap4_panda_vaux1, .vaux2 = &omap4_panda_vaux2, .vaux3 = &omap4_panda_vaux3, + .usb = &omap4_usbphy_data, }; static struct i2c_board_info __initdata omap4_panda_i2c_boardinfo[] = { @@ -377,9 +385,7 @@ static void __init omap4_panda_init(void) /* OMAP4 Panda uses internal transceiver so register nop transceiver */ usb_nop_xceiv_register(); omap4_ehci_init(); - /* FIXME: allow multi-omap to boot until musb is updated for omap4 */ - if (!cpu_is_omap44xx()) - usb_musb_init(&musb_board_data); + usb_musb_init(&musb_board_data); } static void __init omap4_panda_map_io(void) diff --git a/arch/arm/mach-omap2/clock2420_data.c b/arch/arm/mach-omap2/clock2420_data.c index 21f856252ad8..831e25c89d2d 100644 --- a/arch/arm/mach-omap2/clock2420_data.c +++ b/arch/arm/mach-omap2/clock2420_data.c @@ -1877,7 +1877,7 @@ static struct omap_clk omap2420_clks[] = { CLK("omap-aes", "ick", &aes_ick, CK_242X), CLK(NULL, "pka_ick", &pka_ick, CK_242X), CLK(NULL, "usb_fck", &usb_fck, CK_242X), - CLK("musb_hdrc", "fck", &osc_ck, CK_242X), + CLK("musb-hdrc", "fck", &osc_ck, CK_242X), }; /* diff --git a/arch/arm/mach-omap2/clock2430_data.c b/arch/arm/mach-omap2/clock2430_data.c index e32afcbdfb88..a9c60b7843e2 100644 --- a/arch/arm/mach-omap2/clock2430_data.c +++ b/arch/arm/mach-omap2/clock2430_data.c @@ -1983,7 +1983,7 @@ static struct omap_clk omap2430_clks[] = { CLK("omap-aes", "ick", &aes_ick, CK_243X), CLK(NULL, "pka_ick", &pka_ick, CK_243X), CLK(NULL, "usb_fck", &usb_fck, CK_243X), - CLK("musb_hdrc", "ick", &usbhs_ick, CK_243X), + CLK("musb-omap2430", "ick", &usbhs_ick, CK_243X), CLK("mmci-omap-hs.0", "ick", &mmchs1_ick, CK_243X), CLK("mmci-omap-hs.0", "fck", &mmchs1_fck, CK_243X), CLK("mmci-omap-hs.1", "ick", &mmchs2_ick, CK_243X), diff --git a/arch/arm/mach-omap2/clock3xxx_data.c b/arch/arm/mach-omap2/clock3xxx_data.c index d85ecd5aebfd..0579604d4f25 100644 --- a/arch/arm/mach-omap2/clock3xxx_data.c +++ b/arch/arm/mach-omap2/clock3xxx_data.c @@ -3278,6 +3278,7 @@ static struct omap_clk omap3xxx_clks[] = { CLK(NULL, "cpefuse_fck", &cpefuse_fck, CK_3430ES2 | CK_AM35XX), CLK(NULL, "ts_fck", &ts_fck, CK_3430ES2 | CK_AM35XX), CLK(NULL, "usbtll_fck", &usbtll_fck, CK_3430ES2 | CK_AM35XX), + CLK("ehci-omap.0", "usbtll_fck", &usbtll_fck, CK_3430ES2 | CK_AM35XX), CLK("omap-mcbsp.1", "prcm_fck", &core_96m_fck, CK_3XXX), CLK("omap-mcbsp.5", "prcm_fck", &core_96m_fck, CK_3XXX), CLK(NULL, "core_96m_fck", &core_96m_fck, CK_3XXX), @@ -3305,14 +3306,15 @@ static struct omap_clk omap3xxx_clks[] = { CLK(NULL, "ssi_sst_fck", &ssi_sst_fck_3430es1, CK_3430ES1), CLK(NULL, "ssi_sst_fck", &ssi_sst_fck_3430es2, CK_3430ES2), CLK(NULL, "core_l3_ick", &core_l3_ick, CK_3XXX), - CLK("musb_hdrc", "ick", &hsotgusb_ick_3430es1, CK_3430ES1), - CLK("musb_hdrc", "ick", &hsotgusb_ick_3430es2, CK_3430ES2), + CLK("musb-omap2430", "ick", &hsotgusb_ick_3430es1, CK_3430ES1), + CLK("musb-omap2430", "ick", &hsotgusb_ick_3430es2, CK_3430ES2), CLK(NULL, "sdrc_ick", &sdrc_ick, CK_3XXX), CLK(NULL, "gpmc_fck", &gpmc_fck, CK_3XXX), CLK(NULL, "security_l3_ick", &security_l3_ick, CK_343X), CLK(NULL, "pka_ick", &pka_ick, CK_343X), CLK(NULL, "core_l4_ick", &core_l4_ick, CK_3XXX), CLK(NULL, "usbtll_ick", &usbtll_ick, CK_3430ES2 | CK_AM35XX), + CLK("ehci-omap.0", "usbtll_ick", &usbtll_ick, CK_3430ES2 | CK_AM35XX), CLK("mmci-omap-hs.2", "ick", &mmchs3_ick, CK_3430ES2 | CK_AM35XX), CLK(NULL, "icr_ick", &icr_ick, CK_343X), CLK("omap-aes", "ick", &aes2_ick, CK_343X), @@ -3358,8 +3360,11 @@ static struct omap_clk omap3xxx_clks[] = { CLK(NULL, "cam_ick", &cam_ick, CK_343X), CLK(NULL, "csi2_96m_fck", &csi2_96m_fck, CK_343X), CLK(NULL, "usbhost_120m_fck", &usbhost_120m_fck, CK_3430ES2 | CK_AM35XX), + CLK("ehci-omap.0", "hs_fck", &usbhost_120m_fck, CK_3430ES2 | CK_AM35XX), CLK(NULL, "usbhost_48m_fck", &usbhost_48m_fck, CK_3430ES2 | CK_AM35XX), + CLK("ehci-omap.0", "fs_fck", &usbhost_48m_fck, CK_3430ES2 | CK_AM35XX), CLK(NULL, "usbhost_ick", &usbhost_ick, CK_3430ES2 | CK_AM35XX), + CLK("ehci-omap.0", "usbhost_ick", &usbhost_ick, CK_3430ES2 | CK_AM35XX), CLK(NULL, "usim_fck", &usim_fck, CK_3430ES2), CLK(NULL, "gpt1_fck", &gpt1_fck, CK_3XXX), CLK(NULL, "wkup_32k_fck", &wkup_32k_fck, CK_3XXX), @@ -3437,8 +3442,8 @@ static struct omap_clk omap3xxx_clks[] = { CLK("davinci_emac", "phy_clk", &emac_fck, CK_AM35XX), CLK("vpfe-capture", "master", &vpfe_ick, CK_AM35XX), CLK("vpfe-capture", "slave", &vpfe_fck, CK_AM35XX), - CLK("musb_hdrc", "ick", &hsotgusb_ick_am35xx, CK_AM35XX), - CLK("musb_hdrc", "fck", &hsotgusb_fck_am35xx, CK_AM35XX), + CLK("musb-am35x", "ick", &hsotgusb_ick_am35xx, CK_AM35XX), + CLK("musb-am35x", "fck", &hsotgusb_fck_am35xx, CK_AM35XX), CLK(NULL, "hecc_ck", &hecc_ck, CK_AM35XX), CLK(NULL, "uart4_ick", &uart4_ick_am35xx, CK_AM35XX), }; diff --git a/arch/arm/mach-omap2/clock44xx_data.c b/arch/arm/mach-omap2/clock44xx_data.c index 1599836ba3d9..bfcd19f8368c 100644 --- a/arch/arm/mach-omap2/clock44xx_data.c +++ b/arch/arm/mach-omap2/clock44xx_data.c @@ -2937,6 +2937,7 @@ static struct omap_clk omap44xx_clks[] = { CLK(NULL, "uart3_fck", &uart3_fck, CK_443X), CLK(NULL, "uart4_fck", &uart4_fck, CK_443X), CLK(NULL, "usb_host_fs_fck", &usb_host_fs_fck, CK_443X), + CLK("ehci-omap.0", "fs_fck", &usb_host_fs_fck, CK_443X), CLK(NULL, "usb_host_hs_utmi_p3_clk", &usb_host_hs_utmi_p3_clk, CK_443X), CLK(NULL, "usb_host_hs_hsic60m_p1_clk", &usb_host_hs_hsic60m_p1_clk, CK_443X), CLK(NULL, "usb_host_hs_hsic60m_p2_clk", &usb_host_hs_hsic60m_p2_clk, CK_443X), @@ -2948,14 +2949,18 @@ static struct omap_clk omap44xx_clks[] = { CLK(NULL, "usb_host_hs_hsic480m_p2_clk", &usb_host_hs_hsic480m_p2_clk, CK_443X), CLK(NULL, "usb_host_hs_func48mclk", &usb_host_hs_func48mclk, CK_443X), CLK(NULL, "usb_host_hs_fck", &usb_host_hs_fck, CK_443X), + CLK("ehci-omap.0", "hs_fck", &usb_host_hs_fck, CK_443X), + CLK("ehci-omap.0", "usbhost_ick", &dummy_ck, CK_443X), CLK(NULL, "otg_60m_gfclk", &otg_60m_gfclk, CK_443X), CLK(NULL, "usb_otg_hs_xclk", &usb_otg_hs_xclk, CK_443X), - CLK("musb_hdrc", "ick", &usb_otg_hs_ick, CK_443X), + CLK("musb-omap2430", "ick", &usb_otg_hs_ick, CK_443X), CLK(NULL, "usb_phy_cm_clk32k", &usb_phy_cm_clk32k, CK_443X), CLK(NULL, "usb_tll_hs_usb_ch2_clk", &usb_tll_hs_usb_ch2_clk, CK_443X), CLK(NULL, "usb_tll_hs_usb_ch0_clk", &usb_tll_hs_usb_ch0_clk, CK_443X), CLK(NULL, "usb_tll_hs_usb_ch1_clk", &usb_tll_hs_usb_ch1_clk, CK_443X), CLK(NULL, "usb_tll_hs_ick", &usb_tll_hs_ick, CK_443X), + CLK("ehci-omap.0", "usbtll_ick", &usb_tll_hs_ick, CK_443X), + CLK("ehci-omap.0", "usbtll_fck", &dummy_ck, CK_443X), CLK(NULL, "usim_ck", &usim_ck, CK_443X), CLK(NULL, "usim_fclk", &usim_fclk, CK_443X), CLK(NULL, "usim_fck", &usim_fck, CK_443X), diff --git a/arch/arm/mach-omap2/omap_phy_internal.c b/arch/arm/mach-omap2/omap_phy_internal.c new file mode 100644 index 000000000000..745252c60e32 --- /dev/null +++ b/arch/arm/mach-omap2/omap_phy_internal.c @@ -0,0 +1,149 @@ +/* + * This file configures the internal USB PHY in OMAP4430. Used + * with TWL6030 transceiver and MUSB on OMAP4430. + * + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * Author: Hema HK <hemahk@ti.com> + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + */ + +#include <linux/types.h> +#include <linux/delay.h> +#include <linux/clk.h> +#include <linux/io.h> +#include <linux/err.h> +#include <linux/usb.h> + +#include <plat/usb.h> + +/* OMAP control module register for UTMI PHY */ +#define CONTROL_DEV_CONF 0x300 +#define PHY_PD 0x1 + +#define USBOTGHS_CONTROL 0x33c +#define AVALID BIT(0) +#define BVALID BIT(1) +#define VBUSVALID BIT(2) +#define SESSEND BIT(3) +#define IDDIG BIT(4) + +static struct clk *phyclk, *clk48m, *clk32k; +static void __iomem *ctrl_base; + +int omap4430_phy_init(struct device *dev) +{ + ctrl_base = ioremap(OMAP443X_SCM_BASE, SZ_1K); + if (!ctrl_base) { + dev_err(dev, "control module ioremap failed\n"); + return -ENOMEM; + } + /* Power down the phy */ + __raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF); + phyclk = clk_get(dev, "ocp2scp_usb_phy_ick"); + + if (IS_ERR(phyclk)) { + dev_err(dev, "cannot clk_get ocp2scp_usb_phy_ick\n"); + iounmap(ctrl_base); + return PTR_ERR(phyclk); + } + + clk48m = clk_get(dev, "ocp2scp_usb_phy_phy_48m"); + if (IS_ERR(clk48m)) { + dev_err(dev, "cannot clk_get ocp2scp_usb_phy_phy_48m\n"); + clk_put(phyclk); + iounmap(ctrl_base); + return PTR_ERR(clk48m); + } + + clk32k = clk_get(dev, "usb_phy_cm_clk32k"); + if (IS_ERR(clk32k)) { + dev_err(dev, "cannot clk_get usb_phy_cm_clk32k\n"); + clk_put(phyclk); + clk_put(clk48m); + iounmap(ctrl_base); + return PTR_ERR(clk32k); + } + return 0; +} + +int omap4430_phy_set_clk(struct device *dev, int on) +{ + static int state; + + if (on && !state) { + /* Enable the phy clocks */ + clk_enable(phyclk); + clk_enable(clk48m); + clk_enable(clk32k); + state = 1; + } else if (state) { + /* Disable the phy clocks */ + clk_disable(phyclk); + clk_disable(clk48m); + clk_disable(clk32k); + state = 0; + } + return 0; +} + +int omap4430_phy_power(struct device *dev, int ID, int on) +{ + if (on) { + /* enabled the clocks */ + omap4430_phy_set_clk(dev, 1); + /* power on the phy */ + if (__raw_readl(ctrl_base + CONTROL_DEV_CONF) & PHY_PD) { + __raw_writel(~PHY_PD, ctrl_base + CONTROL_DEV_CONF); + mdelay(200); + } + if (ID) + /* enable VBUS valid, IDDIG groung */ + __raw_writel(AVALID | VBUSVALID, ctrl_base + + USBOTGHS_CONTROL); + else + /* + * Enable VBUS Valid, AValid and IDDIG + * high impedence + */ + __raw_writel(IDDIG | AVALID | VBUSVALID, + ctrl_base + USBOTGHS_CONTROL); + } else { + /* Enable session END and IDIG to high impedence. */ + __raw_writel(SESSEND | IDDIG, ctrl_base + + USBOTGHS_CONTROL); + /* Disable the clocks */ + omap4430_phy_set_clk(dev, 0); + /* Power down the phy */ + __raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF); + } + + return 0; +} + +int omap4430_phy_exit(struct device *dev) +{ + if (ctrl_base) + iounmap(ctrl_base); + if (phyclk) + clk_put(phyclk); + if (clk48m) + clk_put(clk48m); + if (clk32k) + clk_put(clk32k); + + return 0; +} diff --git a/arch/arm/mach-omap2/usb-ehci.c b/arch/arm/mach-omap2/usb-ehci.c index b11bf385d360..25eeadabc39b 100644 --- a/arch/arm/mach-omap2/usb-ehci.c +++ b/arch/arm/mach-omap2/usb-ehci.c @@ -34,22 +34,15 @@ static struct resource ehci_resources[] = { { - .start = OMAP34XX_EHCI_BASE, - .end = OMAP34XX_EHCI_BASE + SZ_1K - 1, .flags = IORESOURCE_MEM, }, { - .start = OMAP34XX_UHH_CONFIG_BASE, - .end = OMAP34XX_UHH_CONFIG_BASE + SZ_1K - 1, .flags = IORESOURCE_MEM, }, { - .start = OMAP34XX_USBTLL_BASE, - .end = OMAP34XX_USBTLL_BASE + SZ_4K - 1, .flags = IORESOURCE_MEM, }, { /* general IRQ */ - .start = INT_34XX_EHCI_IRQ, .flags = IORESOURCE_IRQ, } }; @@ -214,13 +207,148 @@ static void setup_ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode) return; } +static void setup_4430ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode) +{ + switch (port_mode[0]) { + case EHCI_HCD_OMAP_MODE_PHY: + omap_mux_init_signal("usbb1_ulpiphy_stp", + OMAP_PIN_OUTPUT); + omap_mux_init_signal("usbb1_ulpiphy_clk", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpiphy_dir", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpiphy_nxt", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpiphy_dat0", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpiphy_dat1", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpiphy_dat2", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpiphy_dat3", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpiphy_dat4", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpiphy_dat5", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpiphy_dat6", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpiphy_dat7", + OMAP_PIN_INPUT_PULLDOWN); + break; + case EHCI_HCD_OMAP_MODE_TLL: + omap_mux_init_signal("usbb1_ulpitll_stp", + OMAP_PIN_INPUT_PULLUP); + omap_mux_init_signal("usbb1_ulpitll_clk", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpitll_dir", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpitll_nxt", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpitll_dat0", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpitll_dat1", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpitll_dat2", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpitll_dat3", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpitll_dat4", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpitll_dat5", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpitll_dat6", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb1_ulpitll_dat7", + OMAP_PIN_INPUT_PULLDOWN); + break; + case EHCI_HCD_OMAP_MODE_UNKNOWN: + default: + break; + } + switch (port_mode[1]) { + case EHCI_HCD_OMAP_MODE_PHY: + omap_mux_init_signal("usbb2_ulpiphy_stp", + OMAP_PIN_OUTPUT); + omap_mux_init_signal("usbb2_ulpiphy_clk", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpiphy_dir", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpiphy_nxt", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpiphy_dat0", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpiphy_dat1", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpiphy_dat2", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpiphy_dat3", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpiphy_dat4", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpiphy_dat5", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpiphy_dat6", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpiphy_dat7", + OMAP_PIN_INPUT_PULLDOWN); + break; + case EHCI_HCD_OMAP_MODE_TLL: + omap_mux_init_signal("usbb2_ulpitll_stp", + OMAP_PIN_INPUT_PULLUP); + omap_mux_init_signal("usbb2_ulpitll_clk", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpitll_dir", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpitll_nxt", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpitll_dat0", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpitll_dat1", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpitll_dat2", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpitll_dat3", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpitll_dat4", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpitll_dat5", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpitll_dat6", + OMAP_PIN_INPUT_PULLDOWN); + omap_mux_init_signal("usbb2_ulpitll_dat7", + OMAP_PIN_INPUT_PULLDOWN); + break; + case EHCI_HCD_OMAP_MODE_UNKNOWN: + default: + break; + } +} + void __init usb_ehci_init(const struct ehci_hcd_omap_platform_data *pdata) { platform_device_add_data(&ehci_device, pdata, sizeof(*pdata)); /* Setup Pin IO MUX for EHCI */ - if (cpu_is_omap34xx()) + if (cpu_is_omap34xx()) { + ehci_resources[0].start = OMAP34XX_EHCI_BASE; + ehci_resources[0].end = OMAP34XX_EHCI_BASE + SZ_1K - 1; + ehci_resources[1].start = OMAP34XX_UHH_CONFIG_BASE; + ehci_resources[1].end = OMAP34XX_UHH_CONFIG_BASE + SZ_1K - 1; + ehci_resources[2].start = OMAP34XX_USBTLL_BASE; + ehci_resources[2].end = OMAP34XX_USBTLL_BASE + SZ_4K - 1; + ehci_resources[3].start = INT_34XX_EHCI_IRQ; setup_ehci_io_mux(pdata->port_mode); + } else if (cpu_is_omap44xx()) { + ehci_resources[0].start = OMAP44XX_HSUSB_EHCI_BASE; + ehci_resources[0].end = OMAP44XX_HSUSB_EHCI_BASE + SZ_1K - 1; + ehci_resources[1].start = OMAP44XX_UHH_CONFIG_BASE; + ehci_resources[1].end = OMAP44XX_UHH_CONFIG_BASE + SZ_2K - 1; + ehci_resources[2].start = OMAP44XX_USBTLL_BASE; + ehci_resources[2].end = OMAP44XX_USBTLL_BASE + SZ_4K - 1; + ehci_resources[3].start = OMAP44XX_IRQ_EHCI; + setup_4430ehci_io_mux(pdata->port_mode); + } if (platform_device_register(&ehci_device) < 0) { printk(KERN_ERR "Unable to register HS-USB (EHCI) device\n"); diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c index 72605584bfff..5298949d4b11 100644 --- a/arch/arm/mach-omap2/usb-musb.c +++ b/arch/arm/mach-omap2/usb-musb.c @@ -30,8 +30,101 @@ #include <mach/irqs.h> #include <mach/am35xx.h> #include <plat/usb.h> +#include "control.h" -#ifdef CONFIG_USB_MUSB_SOC +#if defined(CONFIG_USB_MUSB_OMAP2PLUS) || defined (CONFIG_USB_MUSB_AM35X) + +static void am35x_musb_reset(void) +{ + u32 regval; + + /* Reset the musb interface */ + regval = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET); + + regval |= AM35XX_USBOTGSS_SW_RST; + omap_ctrl_writel(regval, AM35XX_CONTROL_IP_SW_RESET); + + regval &= ~AM35XX_USBOTGSS_SW_RST; + omap_ctrl_writel(regval, AM35XX_CONTROL_IP_SW_RESET); + + regval = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET); +} + +static void am35x_musb_phy_power(u8 on) +{ + unsigned long timeout = jiffies + msecs_to_jiffies(100); + u32 devconf2; + + if (on) { + /* + * Start the on-chip PHY and its PLL. + */ + devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2); + + devconf2 &= ~(CONF2_RESET | CONF2_PHYPWRDN | CONF2_OTGPWRDN); + devconf2 |= CONF2_PHY_PLLON; + + omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2); + + pr_info(KERN_INFO "Waiting for PHY clock good...\n"); + while (!(omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2) + & CONF2_PHYCLKGD)) { + cpu_relax(); + + if (time_after(jiffies, timeout)) { + pr_err(KERN_ERR "musb PHY clock good timed out\n"); + break; + } + } + } else { + /* + * Power down the on-chip PHY. + */ + devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2); + + devconf2 &= ~CONF2_PHY_PLLON; + devconf2 |= CONF2_PHYPWRDN | CONF2_OTGPWRDN; + omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2); + } +} + +static void am35x_musb_clear_irq(void) +{ + u32 regval; + + regval = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR); + regval |= AM35XX_USBOTGSS_INT_CLR; + omap_ctrl_writel(regval, AM35XX_CONTROL_LVL_INTR_CLEAR); + regval = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR); +} + +static void am35x_musb_set_mode(u8 musb_mode) +{ + u32 devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2); + + devconf2 &= ~CONF2_OTGMODE; + switch (musb_mode) { +#ifdef CONFIG_USB_MUSB_HDRC_HCD + case MUSB_HOST: /* Force VBUS valid, ID = 0 */ + devconf2 |= CONF2_FORCE_HOST; + break; +#endif +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + case MUSB_PERIPHERAL: /* Force VBUS valid, ID = 1 */ + devconf2 |= CONF2_FORCE_DEVICE; + break; +#endif +#ifdef CONFIG_USB_MUSB_OTG + case MUSB_OTG: /* Don't override the VBUS/ID comparators */ + devconf2 |= CONF2_NO_OVERRIDE; + break; +#endif + default: + pr_info(KERN_INFO "Unsupported mode %u\n", musb_mode); + } + + omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2); +} static struct resource musb_resources[] = { [0] = { /* start and end set dynamically */ @@ -40,10 +133,12 @@ static struct resource musb_resources[] = { [1] = { /* general IRQ */ .start = INT_243X_HS_USB_MC, .flags = IORESOURCE_IRQ, + .name = "mc", }, [2] = { /* DMA IRQ */ .start = INT_243X_HS_USB_DMA, .flags = IORESOURCE_IRQ, + .name = "dma", }, }; @@ -75,7 +170,7 @@ static struct musb_hdrc_platform_data musb_plat = { static u64 musb_dmamask = DMA_BIT_MASK(32); static struct platform_device musb_device = { - .name = "musb_hdrc", + .name = "musb-omap2430", .id = -1, .dev = { .dma_mask = &musb_dmamask, @@ -91,8 +186,13 @@ void __init usb_musb_init(struct omap_musb_board_data *board_data) if (cpu_is_omap243x()) { musb_resources[0].start = OMAP243X_HS_BASE; } else if (cpu_is_omap3517() || cpu_is_omap3505()) { + musb_device.name = "musb-am35x"; musb_resources[0].start = AM35XX_IPSS_USBOTGSS_BASE; musb_resources[1].start = INT_35XX_USBOTG_IRQ; + board_data->set_phy_power = am35x_musb_phy_power; + board_data->clear_irq = am35x_musb_clear_irq; + board_data->set_mode = am35x_musb_set_mode; + board_data->reset = am35x_musb_reset; } else if (cpu_is_omap34xx()) { musb_resources[0].start = OMAP34XX_HSUSB_OTG_BASE; } else if (cpu_is_omap44xx()) { diff --git a/arch/arm/mach-omap2/usb-tusb6010.c b/arch/arm/mach-omap2/usb-tusb6010.c index 64a0112b70a5..7cb3c18a5e20 100644 --- a/arch/arm/mach-omap2/usb-tusb6010.c +++ b/arch/arm/mach-omap2/usb-tusb6010.c @@ -223,7 +223,7 @@ static struct resource tusb_resources[] = { static u64 tusb_dmamask = ~(u32)0; static struct platform_device tusb_device = { - .name = "musb_hdrc", + .name = "musb-tusb", .id = -1, .dev = { .dma_mask = &tusb_dmamask, diff --git a/arch/arm/plat-omap/include/plat/omap44xx.h b/arch/arm/plat-omap/include/plat/omap44xx.h index 8b3f12ff5cbc..ea2b8a6306e7 100644 --- a/arch/arm/plat-omap/include/plat/omap44xx.h +++ b/arch/arm/plat-omap/include/plat/omap44xx.h @@ -52,5 +52,10 @@ #define OMAP4_MMU1_BASE 0x55082000 #define OMAP4_MMU2_BASE 0x4A066000 +#define OMAP44XX_USBTLL_BASE (L4_44XX_BASE + 0x62000) +#define OMAP44XX_UHH_CONFIG_BASE (L4_44XX_BASE + 0x64000) +#define OMAP44XX_HSUSB_OHCI_BASE (L4_44XX_BASE + 0x64800) +#define OMAP44XX_HSUSB_EHCI_BASE (L4_44XX_BASE + 0x64C00) + #endif /* __ASM_ARCH_OMAP44XX_H */ diff --git a/arch/arm/plat-omap/include/plat/usb.h b/arch/arm/plat-omap/include/plat/usb.h index 59c7fe731f28..450a332f1009 100644 --- a/arch/arm/plat-omap/include/plat/usb.h +++ b/arch/arm/plat-omap/include/plat/usb.h @@ -11,6 +11,7 @@ enum ehci_hcd_omap_mode { EHCI_HCD_OMAP_MODE_UNKNOWN, EHCI_HCD_OMAP_MODE_PHY, EHCI_HCD_OMAP_MODE_TLL, + EHCI_HCD_OMAP_MODE_HSIC, }; enum ohci_omap3_port_mode { @@ -69,6 +70,10 @@ struct omap_musb_board_data { u8 mode; u16 power; unsigned extvbus:1; + void (*set_phy_power)(u8 on); + void (*clear_irq)(void); + void (*set_mode)(u8 mode); + void (*reset)(void); }; enum musb_interface {MUSB_INTERFACE_ULPI, MUSB_INTERFACE_UTMI}; @@ -79,6 +84,11 @@ extern void usb_ehci_init(const struct ehci_hcd_omap_platform_data *pdata); extern void usb_ohci_init(const struct ohci_hcd_omap_platform_data *pdata); +extern int omap4430_phy_power(struct device *dev, int ID, int on); +extern int omap4430_phy_set_clk(struct device *dev, int on); +extern int omap4430_phy_init(struct device *dev); +extern int omap4430_phy_exit(struct device *dev); + #endif diff --git a/arch/blackfin/mach-bf527/boards/ad7160eval.c b/arch/blackfin/mach-bf527/boards/ad7160eval.c index fc767ac76381..52295fff5577 100644 --- a/arch/blackfin/mach-bf527/boards/ad7160eval.c +++ b/arch/blackfin/mach-bf527/boards/ad7160eval.c @@ -83,7 +83,7 @@ static struct musb_hdrc_platform_data musb_plat = { static u64 musb_dmamask = ~(u32)0; static struct platform_device musb_device = { - .name = "musb_hdrc", + .name = "musb-blackfin", .id = 0, .dev = { .dma_mask = &musb_dmamask, diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c index 2c31af7a320a..50533edc3994 100644 --- a/arch/blackfin/mach-bf527/boards/cm_bf527.c +++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c @@ -82,11 +82,13 @@ static struct resource musb_resources[] = { .start = IRQ_USB_INT0, .end = IRQ_USB_INT0, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .name = "mc" }, [2] = { /* DMA IRQ */ .start = IRQ_USB_DMA, .end = IRQ_USB_DMA, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .name = "dma" }, }; @@ -118,7 +120,7 @@ static struct musb_hdrc_platform_data musb_plat = { static u64 musb_dmamask = ~(u32)0; static struct platform_device musb_device = { - .name = "musb_hdrc", + .name = "musb-blackfin", .id = 0, .dev = { .dma_mask = &musb_dmamask, diff --git a/arch/blackfin/mach-bf527/boards/ezbrd.c b/arch/blackfin/mach-bf527/boards/ezbrd.c index 9a736a850c5c..d06177b5fe22 100644 --- a/arch/blackfin/mach-bf527/boards/ezbrd.c +++ b/arch/blackfin/mach-bf527/boards/ezbrd.c @@ -46,11 +46,13 @@ static struct resource musb_resources[] = { .start = IRQ_USB_INT0, .end = IRQ_USB_INT0, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .name = "mc" }, [2] = { /* DMA IRQ */ .start = IRQ_USB_DMA, .end = IRQ_USB_DMA, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .name = "dma" }, }; @@ -82,7 +84,7 @@ static struct musb_hdrc_platform_data musb_plat = { static u64 musb_dmamask = ~(u32)0; static struct platform_device musb_device = { - .name = "musb_hdrc", + .name = "musb-blackfin", .id = 0, .dev = { .dma_mask = &musb_dmamask, diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c index 9222bc00bbd3..35a88a5a5013 100644 --- a/arch/blackfin/mach-bf527/boards/ezkit.c +++ b/arch/blackfin/mach-bf527/boards/ezkit.c @@ -86,11 +86,13 @@ static struct resource musb_resources[] = { .start = IRQ_USB_INT0, .end = IRQ_USB_INT0, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .name = "mc" }, [2] = { /* DMA IRQ */ .start = IRQ_USB_DMA, .end = IRQ_USB_DMA, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .name = "dma" }, }; @@ -122,7 +124,7 @@ static struct musb_hdrc_platform_data musb_plat = { static u64 musb_dmamask = ~(u32)0; static struct platform_device musb_device = { - .name = "musb_hdrc", + .name = "musb-blackfin", .id = 0, .dev = { .dma_mask = &musb_dmamask, diff --git a/arch/blackfin/mach-bf527/boards/tll6527m.c b/arch/blackfin/mach-bf527/boards/tll6527m.c index 9ec575729e2c..130861bd2589 100644 --- a/arch/blackfin/mach-bf527/boards/tll6527m.c +++ b/arch/blackfin/mach-bf527/boards/tll6527m.c @@ -91,7 +91,7 @@ static struct musb_hdrc_platform_data musb_plat = { static u64 musb_dmamask = ~(u32)0; static struct platform_device musb_device = { - .name = "musb_hdrc", + .name = "musb-blackfin", .id = 0, .dev = { .dma_mask = &musb_dmamask, diff --git a/arch/blackfin/mach-bf548/boards/cm_bf548.c b/arch/blackfin/mach-bf548/boards/cm_bf548.c index f0c0eef95ba8..4c2ee6789099 100644 --- a/arch/blackfin/mach-bf548/boards/cm_bf548.c +++ b/arch/blackfin/mach-bf548/boards/cm_bf548.c @@ -482,11 +482,13 @@ static struct resource musb_resources[] = { .start = IRQ_USB_INT0, .end = IRQ_USB_INT0, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .name = "mc" }, [2] = { /* DMA IRQ */ .start = IRQ_USB_DMA, .end = IRQ_USB_DMA, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .name = "dma" }, }; @@ -518,7 +520,7 @@ static struct musb_hdrc_platform_data musb_plat = { static u64 musb_dmamask = ~(u32)0; static struct platform_device musb_device = { - .name = "musb_hdrc", + .name = "musb-blackfin", .id = 0, .dev = { .dma_mask = &musb_dmamask, diff --git a/arch/blackfin/mach-bf548/boards/ezkit.c b/arch/blackfin/mach-bf548/boards/ezkit.c index 216e26999af9..4f03fbc4c9be 100644 --- a/arch/blackfin/mach-bf548/boards/ezkit.c +++ b/arch/blackfin/mach-bf548/boards/ezkit.c @@ -587,11 +587,13 @@ static struct resource musb_resources[] = { .start = IRQ_USB_INT0, .end = IRQ_USB_INT0, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .name = "mc" }, [2] = { /* DMA IRQ */ .start = IRQ_USB_DMA, .end = IRQ_USB_DMA, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + .name = "dma" }, }; @@ -623,7 +625,7 @@ static struct musb_hdrc_platform_data musb_plat = { static u64 musb_dmamask = ~(u32)0; static struct platform_device musb_device = { - .name = "musb_hdrc", + .name = "musb-blackfin", .id = 0, .dev = { .dma_mask = &musb_dmamask, diff --git a/arch/sh/Kconfig b/arch/sh/Kconfig index 2e9d78d21fd3..430e46788609 100644 --- a/arch/sh/Kconfig +++ b/arch/sh/Kconfig @@ -346,6 +346,7 @@ config CPU_SUBTYPE_SH7720 select CPU_SH3 select CPU_HAS_DSP select SYS_SUPPORTS_CMT + select USB_ARCH_HAS_OHCI help Select SH7720 if you have a SH3-DSP SH7720 CPU. @@ -354,6 +355,7 @@ config CPU_SUBTYPE_SH7721 select CPU_SH3 select CPU_HAS_DSP select SYS_SUPPORTS_CMT + select USB_ARCH_HAS_OHCI help Select SH7721 if you have a SH3-DSP SH7721 CPU. @@ -431,6 +433,7 @@ config CPU_SUBTYPE_SH7757 config CPU_SUBTYPE_SH7763 bool "Support SH7763 processor" select CPU_SH4A + select USB_ARCH_HAS_OHCI help Select SH7763 if you have a SH4A SH7763(R5S77631) CPU. @@ -455,6 +458,8 @@ config CPU_SUBTYPE_SH7786 select CPU_SHX3 select CPU_HAS_PTEAEX select GENERIC_CLOCKEVENTS_BROADCAST if SMP + select USB_ARCH_HAS_OHCI + select USB_ARCH_HAS_EHCI config CPU_SUBTYPE_SHX3 bool "Support SH-X3 processor" diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7786.c b/arch/sh/kernel/cpu/sh4a/setup-sh7786.c index c016c0004714..0170dbda1d00 100644 --- a/arch/sh/kernel/cpu/sh4a/setup-sh7786.c +++ b/arch/sh/kernel/cpu/sh4a/setup-sh7786.c @@ -522,10 +522,37 @@ static struct platform_device dma0_device = { }, }; +#define USB_EHCI_START 0xffe70000 +#define USB_OHCI_START 0xffe70400 + +static struct resource usb_ehci_resources[] = { + [0] = { + .start = USB_EHCI_START, + .end = USB_EHCI_START + 0x3ff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = 77, + .end = 77, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device usb_ehci_device = { + .name = "sh_ehci", + .id = -1, + .dev = { + .dma_mask = &usb_ehci_device.dev.coherent_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + }, + .num_resources = ARRAY_SIZE(usb_ehci_resources), + .resource = usb_ehci_resources, +}; + static struct resource usb_ohci_resources[] = { [0] = { - .start = 0xffe70400, - .end = 0xffe704ff, + .start = USB_OHCI_START, + .end = USB_OHCI_START + 0x3ff, .flags = IORESOURCE_MEM, }, [1] = { @@ -535,12 +562,11 @@ static struct resource usb_ohci_resources[] = { }, }; -static u64 usb_ohci_dma_mask = DMA_BIT_MASK(32); static struct platform_device usb_ohci_device = { .name = "sh_ohci", .id = -1, .dev = { - .dma_mask = &usb_ohci_dma_mask, + .dma_mask = &usb_ohci_device.dev.coherent_dma_mask, .coherent_dma_mask = DMA_BIT_MASK(32), }, .num_resources = ARRAY_SIZE(usb_ohci_resources), @@ -570,6 +596,7 @@ static struct platform_device *sh7786_early_devices[] __initdata = { static struct platform_device *sh7786_devices[] __initdata = { &dma0_device, + &usb_ehci_device, &usb_ohci_device, }; diff --git a/drivers/media/video/tlg2300/pd-main.c b/drivers/media/video/tlg2300/pd-main.c index c91424c0c135..99c81a9a4f46 100644 --- a/drivers/media/video/tlg2300/pd-main.c +++ b/drivers/media/video/tlg2300/pd-main.c @@ -452,7 +452,8 @@ static int poseidon_probe(struct usb_interface *interface, device_init_wakeup(&udev->dev, 1); #ifdef CONFIG_PM - pd->udev->autosuspend_delay = HZ * PM_SUSPEND_DELAY; + pm_runtime_set_autosuspend_delay(&pd->udev->dev, + 1000 * PM_SUSPEND_DELAY); usb_enable_autosuspend(pd->udev); if (in_hibernation(pd)) { diff --git a/drivers/mfd/twl-core.c b/drivers/mfd/twl-core.c index 35275ba7096f..12abd5b924b3 100644 --- a/drivers/mfd/twl-core.c +++ b/drivers/mfd/twl-core.c @@ -95,7 +95,8 @@ #define twl_has_rtc() false #endif -#if defined(CONFIG_TWL4030_USB) || defined(CONFIG_TWL4030_USB_MODULE) +#if defined(CONFIG_TWL4030_USB) || defined(CONFIG_TWL4030_USB_MODULE) ||\ + defined(CONFIG_TWL6030_USB) || defined(CONFIG_TWL6030_USB_MODULE) #define twl_has_usb() true #else #define twl_has_usb() false @@ -682,6 +683,43 @@ add_children(struct twl4030_platform_data *pdata, unsigned long features) usb3v1.dev = child; } } + if (twl_has_usb() && pdata->usb && twl_class_is_6030()) { + + static struct regulator_consumer_supply usb3v3 = { + .supply = "vusb", + }; + + if (twl_has_regulator()) { + /* this is a template that gets copied */ + struct regulator_init_data usb_fixed = { + .constraints.valid_modes_mask = + REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .constraints.valid_ops_mask = + REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }; + + child = add_regulator_linked(TWL6030_REG_VUSB, + &usb_fixed, &usb3v3, 1); + if (IS_ERR(child)) + return PTR_ERR(child); + } + + child = add_child(0, "twl6030_usb", + pdata->usb, sizeof(*pdata->usb), + true, + /* irq1 = VBUS_PRES, irq0 = USB ID */ + pdata->irq_base + USBOTG_INTR_OFFSET, + pdata->irq_base + USB_PRES_INTR_OFFSET); + + if (IS_ERR(child)) + return PTR_ERR(child); + /* we need to connect regulators to this transceiver */ + if (twl_has_regulator() && child) + usb3v3.dev = child; + + } if (twl_has_watchdog()) { child = add_child(0, "twl4030_wdt", NULL, 0, false, 0, 0); @@ -815,10 +853,6 @@ add_children(struct twl4030_platform_data *pdata, unsigned long features) if (IS_ERR(child)) return PTR_ERR(child); - child = add_regulator(TWL6030_REG_VUSB, pdata->vusb); - if (IS_ERR(child)) - return PTR_ERR(child); - child = add_regulator(TWL6030_REG_VAUX1_6030, pdata->vaux1); if (IS_ERR(child)) return PTR_ERR(child); diff --git a/drivers/mfd/twl6030-irq.c b/drivers/mfd/twl6030-irq.c index aaedb11d9d2c..06c8955907e9 100644 --- a/drivers/mfd/twl6030-irq.c +++ b/drivers/mfd/twl6030-irq.c @@ -74,7 +74,7 @@ static int twl6030_interrupt_mapping[24] = { USBOTG_INTR_OFFSET, /* Bit 16 ID_WKUP */ USBOTG_INTR_OFFSET, /* Bit 17 VBUS_WKUP */ USBOTG_INTR_OFFSET, /* Bit 18 ID */ - USBOTG_INTR_OFFSET, /* Bit 19 VBUS */ + USB_PRES_INTR_OFFSET, /* Bit 19 VBUS */ CHARGER_INTR_OFFSET, /* Bit 20 CHRG_CTRL */ CHARGER_INTR_OFFSET, /* Bit 21 EXT_CHRG */ CHARGER_INTR_OFFSET, /* Bit 22 INT_CHRG */ @@ -128,6 +128,13 @@ static int twl6030_irq_thread(void *data) sts.bytes[3] = 0; /* Only 24 bits are valid*/ + /* + * Since VBUS status bit is not reliable for VBUS disconnect + * use CHARGER VBUS detection status bit instead. + */ + if (sts.bytes[2] & 0x10) + sts.bytes[2] |= 0x08; + for (i = 0; sts.int_sts; sts.int_sts >>= 1, i++) { local_irq_disable(); if (sts.int_sts & 0x1) { diff --git a/drivers/net/wimax/i2400m/usb.c b/drivers/net/wimax/i2400m/usb.c index d3365ac85dde..7cb375515e1e 100644 --- a/drivers/net/wimax/i2400m/usb.c +++ b/drivers/net/wimax/i2400m/usb.c @@ -514,7 +514,7 @@ int i2400mu_probe(struct usb_interface *iface, #ifdef CONFIG_PM iface->needs_remote_wakeup = 1; /* autosuspend (15s delay) */ device_init_wakeup(dev, 1); - usb_dev->autosuspend_delay = 15 * HZ; + pm_runtime_set_autosuspend_delay(&usb_dev->dev, 15000); usb_enable_autosuspend(usb_dev); #endif diff --git a/drivers/staging/bcm/InterfaceInit.c b/drivers/staging/bcm/InterfaceInit.c index 824f9a45007a..e97ad99b1bb4 100644 --- a/drivers/staging/bcm/InterfaceInit.c +++ b/drivers/staging/bcm/InterfaceInit.c @@ -277,7 +277,7 @@ usbbcm_device_probe(struct usb_interface *intf, const struct usb_device_id *id) if(psAdapter->bDoSuspend) { #ifdef CONFIG_PM - udev->autosuspend_delay = 0; + pm_runtime_set_autosuspend_delay(&udev->dev, 0); intf->needs_remote_wakeup = 1; #if LINUX_VERSION_CODE < KERNEL_VERSION(2, 6, 35) udev->autosuspend_disabled = 0; diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig index 67eb3770868f..b8e70a982fd4 100644 --- a/drivers/usb/Kconfig +++ b/drivers/usb/Kconfig @@ -41,17 +41,13 @@ config USB_ARCH_HAS_OHCI default y if MFD_TC6393XB default y if ARCH_W90X900 default y if ARCH_DAVINCI_DA8XX + default y if PLAT_SPEAR # PPC: default y if STB03xxx default y if PPC_MPC52xx # MIPS: default y if MIPS_ALCHEMY default y if MACH_JZ4740 - # SH: - default y if CPU_SUBTYPE_SH7720 - default y if CPU_SUBTYPE_SH7721 - default y if CPU_SUBTYPE_SH7763 - default y if CPU_SUBTYPE_SH7786 # more: default PCI @@ -66,6 +62,9 @@ config USB_ARCH_HAS_EHCI default y if ARCH_AT91SAM9G45 default y if ARCH_MXC default y if ARCH_OMAP3 + default y if ARCH_VT8500 + default y if PLAT_SPEAR + default y if ARCH_MSM default PCI # ARM SA1111 chips have a non-PCI based "OHCI-compatible" USB host interface. diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c index c0e60fbcb048..b9278a1fb9e5 100644 --- a/drivers/usb/core/driver.c +++ b/drivers/usb/core/driver.c @@ -27,7 +27,6 @@ #include <linux/usb.h> #include <linux/usb/quirks.h> #include <linux/usb/hcd.h> -#include <linux/pm_runtime.h> #include "usb.h" @@ -1262,6 +1261,7 @@ static int usb_resume_both(struct usb_device *udev, pm_message_t msg) udev->reset_resume); } } + usb_mark_last_busy(udev); done: dev_vdbg(&udev->dev, "%s: status %d\n", __func__, status); @@ -1329,7 +1329,6 @@ int usb_resume(struct device *dev, pm_message_t msg) pm_runtime_disable(dev); pm_runtime_set_active(dev); pm_runtime_enable(dev); - udev->last_busy = jiffies; do_unbind_rebind(udev, DO_REBIND); } } @@ -1397,33 +1396,8 @@ void usb_autosuspend_device(struct usb_device *udev) { int status; - udev->last_busy = jiffies; - status = pm_runtime_put_sync(&udev->dev); - dev_vdbg(&udev->dev, "%s: cnt %d -> %d\n", - __func__, atomic_read(&udev->dev.power.usage_count), - status); -} - -/** - * usb_try_autosuspend_device - attempt an autosuspend of a USB device and its interfaces - * @udev: the usb_device to autosuspend - * - * This routine should be called when a core subsystem thinks @udev may - * be ready to autosuspend. - * - * @udev's usage counter left unchanged. If it is 0 and all the interfaces - * are inactive then an autosuspend will be attempted. The attempt may - * fail or be delayed. - * - * The caller must hold @udev's device lock. - * - * This routine can run only in process context. - */ -void usb_try_autosuspend_device(struct usb_device *udev) -{ - int status; - - status = pm_runtime_idle(&udev->dev); + usb_mark_last_busy(udev); + status = pm_runtime_put_sync_autosuspend(&udev->dev); dev_vdbg(&udev->dev, "%s: cnt %d -> %d\n", __func__, atomic_read(&udev->dev.power.usage_count), status); @@ -1482,7 +1456,7 @@ void usb_autopm_put_interface(struct usb_interface *intf) struct usb_device *udev = interface_to_usbdev(intf); int status; - udev->last_busy = jiffies; + usb_mark_last_busy(udev); atomic_dec(&intf->pm_usage_cnt); status = pm_runtime_put_sync(&intf->dev); dev_vdbg(&intf->dev, "%s: cnt %d -> %d\n", @@ -1509,32 +1483,11 @@ EXPORT_SYMBOL_GPL(usb_autopm_put_interface); void usb_autopm_put_interface_async(struct usb_interface *intf) { struct usb_device *udev = interface_to_usbdev(intf); - unsigned long last_busy; - int status = 0; + int status; - last_busy = udev->last_busy; - udev->last_busy = jiffies; + usb_mark_last_busy(udev); atomic_dec(&intf->pm_usage_cnt); - pm_runtime_put_noidle(&intf->dev); - - if (udev->dev.power.runtime_auto) { - /* Optimization: Don't schedule a delayed autosuspend if - * the timer is already running and the expiration time - * wouldn't change. - * - * We have to use the interface's timer. Attempts to - * schedule a suspend for the device would fail because - * the interface is still active. - */ - if (intf->dev.power.timer_expires == 0 || - round_jiffies_up(last_busy) != - round_jiffies_up(jiffies)) { - status = pm_schedule_suspend(&intf->dev, - jiffies_to_msecs( - round_jiffies_up_relative( - udev->autosuspend_delay))); - } - } + status = pm_runtime_put(&intf->dev); dev_vdbg(&intf->dev, "%s: cnt %d -> %d\n", __func__, atomic_read(&intf->dev.power.usage_count), status); @@ -1554,7 +1507,7 @@ void usb_autopm_put_interface_no_suspend(struct usb_interface *intf) { struct usb_device *udev = interface_to_usbdev(intf); - udev->last_busy = jiffies; + usb_mark_last_busy(udev); atomic_dec(&intf->pm_usage_cnt); pm_runtime_put_noidle(&intf->dev); } @@ -1612,18 +1565,9 @@ EXPORT_SYMBOL_GPL(usb_autopm_get_interface); */ int usb_autopm_get_interface_async(struct usb_interface *intf) { - int status = 0; - enum rpm_status s; - - /* Don't request a resume unless the interface is already suspending - * or suspended. Doing so would force a running suspend timer to be - * cancelled. - */ - pm_runtime_get_noresume(&intf->dev); - s = ACCESS_ONCE(intf->dev.power.runtime_status); - if (s == RPM_SUSPENDING || s == RPM_SUSPENDED) - status = pm_request_resume(&intf->dev); + int status; + status = pm_runtime_get(&intf->dev); if (status < 0 && status != -EINPROGRESS) pm_runtime_put_noidle(&intf->dev); else @@ -1650,7 +1594,7 @@ void usb_autopm_get_interface_no_resume(struct usb_interface *intf) { struct usb_device *udev = interface_to_usbdev(intf); - udev->last_busy = jiffies; + usb_mark_last_busy(udev); atomic_inc(&intf->pm_usage_cnt); pm_runtime_get_noresume(&intf->dev); } @@ -1661,7 +1605,6 @@ static int autosuspend_check(struct usb_device *udev) { int w, i; struct usb_interface *intf; - unsigned long suspend_time, j; /* Fail if autosuspend is disabled, or any interfaces are in use, or * any interface drivers require remote wakeup but it isn't available. @@ -1701,87 +1644,46 @@ static int autosuspend_check(struct usb_device *udev) return -EOPNOTSUPP; } udev->do_remote_wakeup = w; - - /* If everything is okay but the device hasn't been idle for long - * enough, queue a delayed autosuspend request. - */ - j = ACCESS_ONCE(jiffies); - suspend_time = udev->last_busy + udev->autosuspend_delay; - if (time_before(j, suspend_time)) { - pm_schedule_suspend(&udev->dev, jiffies_to_msecs( - round_jiffies_up_relative(suspend_time - j))); - return -EAGAIN; - } return 0; } static int usb_runtime_suspend(struct device *dev) { - int status = 0; + struct usb_device *udev = to_usb_device(dev); + int status; /* A USB device can be suspended if it passes the various autosuspend * checks. Runtime suspend for a USB device means suspending all the * interfaces and then the device itself. */ - if (is_usb_device(dev)) { - struct usb_device *udev = to_usb_device(dev); - - if (autosuspend_check(udev) != 0) - return -EAGAIN; - - status = usb_suspend_both(udev, PMSG_AUTO_SUSPEND); - - /* If an interface fails the suspend, adjust the last_busy - * time so that we don't get another suspend attempt right - * away. - */ - if (status) { - udev->last_busy = jiffies + - (udev->autosuspend_delay == 0 ? - HZ/2 : 0); - } - - /* Prevent the parent from suspending immediately after */ - else if (udev->parent) - udev->parent->last_busy = jiffies; - } + if (autosuspend_check(udev) != 0) + return -EAGAIN; - /* Runtime suspend for a USB interface doesn't mean anything. */ + status = usb_suspend_both(udev, PMSG_AUTO_SUSPEND); return status; } static int usb_runtime_resume(struct device *dev) { + struct usb_device *udev = to_usb_device(dev); + int status; + /* Runtime resume for a USB device means resuming both the device * and all its interfaces. */ - if (is_usb_device(dev)) { - struct usb_device *udev = to_usb_device(dev); - int status; - - status = usb_resume_both(udev, PMSG_AUTO_RESUME); - udev->last_busy = jiffies; - return status; - } - - /* Runtime resume for a USB interface doesn't mean anything. */ - return 0; + status = usb_resume_both(udev, PMSG_AUTO_RESUME); + return status; } static int usb_runtime_idle(struct device *dev) { + struct usb_device *udev = to_usb_device(dev); + /* An idle USB device can be suspended if it passes the various - * autosuspend checks. An idle interface can be suspended at - * any time. + * autosuspend checks. */ - if (is_usb_device(dev)) { - struct usb_device *udev = to_usb_device(dev); - - if (autosuspend_check(udev) != 0) - return 0; - } - - pm_runtime_suspend(dev); + if (autosuspend_check(udev) == 0) + pm_runtime_autosuspend(dev); return 0; } diff --git a/drivers/usb/core/hcd-pci.c b/drivers/usb/core/hcd-pci.c index 3799573bd385..b55d46070a25 100644 --- a/drivers/usb/core/hcd-pci.c +++ b/drivers/usb/core/hcd-pci.c @@ -19,7 +19,6 @@ #include <linux/kernel.h> #include <linux/module.h> #include <linux/pci.h> -#include <linux/pm_runtime.h> #include <linux/usb.h> #include <linux/usb/hcd.h> diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c index ced846ac4141..6a95017fa62b 100644 --- a/drivers/usb/core/hcd.c +++ b/drivers/usb/core/hcd.c @@ -38,7 +38,6 @@ #include <asm/unaligned.h> #include <linux/platform_device.h> #include <linux/workqueue.h> -#include <linux/pm_runtime.h> #include <linux/usb.h> #include <linux/usb/hcd.h> diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index 27115b45edc5..b98efae6a1cf 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -24,7 +24,6 @@ #include <linux/kthread.h> #include <linux/mutex.h> #include <linux/freezer.h> -#include <linux/pm_runtime.h> #include <asm/uaccess.h> #include <asm/byteorder.h> @@ -1804,8 +1803,15 @@ int usb_new_device(struct usb_device *udev) /* Tell the runtime-PM framework the device is active */ pm_runtime_set_active(&udev->dev); + pm_runtime_get_noresume(&udev->dev); + pm_runtime_use_autosuspend(&udev->dev); pm_runtime_enable(&udev->dev); + /* By default, forbid autosuspend for all devices. It will be + * allowed for hubs during binding. + */ + usb_disable_autosuspend(udev); + err = usb_enumerate_device(udev); /* Read descriptors */ if (err < 0) goto fail; @@ -1831,6 +1837,8 @@ int usb_new_device(struct usb_device *udev) } (void) usb_create_ep_devs(&udev->dev, &udev->ep0, udev); + usb_mark_last_busy(udev); + pm_runtime_put_sync_autosuspend(&udev->dev); return err; fail: @@ -2221,6 +2229,7 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg) usb_set_device_state(udev, USB_STATE_SUSPENDED); msleep(10); } + usb_mark_last_busy(hub->hdev); return status; } diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c index d6e3e410477e..832487423826 100644 --- a/drivers/usb/core/message.c +++ b/drivers/usb/core/message.c @@ -1804,6 +1804,7 @@ free_interfaces: INIT_WORK(&intf->reset_ws, __usb_queue_reset_device); intf->minor = -1; device_initialize(&intf->dev); + pm_runtime_no_callbacks(&intf->dev); dev_set_name(&intf->dev, "%d-%s:%d.%d", dev->bus->busnum, dev->devpath, configuration, alt->desc.bInterfaceNumber); diff --git a/drivers/usb/core/quirks.c b/drivers/usb/core/quirks.c index 25719da45e33..44c595432d6f 100644 --- a/drivers/usb/core/quirks.c +++ b/drivers/usb/core/quirks.c @@ -117,21 +117,6 @@ void usb_detect_quirks(struct usb_device *udev) dev_dbg(&udev->dev, "USB quirks for this device: %x\n", udev->quirks); -#ifdef CONFIG_USB_SUSPEND - - /* By default, disable autosuspend for all devices. The hub driver - * will enable it for hubs. - */ - usb_disable_autosuspend(udev); - - /* Autosuspend can also be disabled if the initial autosuspend_delay - * is negative. - */ - if (udev->autosuspend_delay < 0) - usb_autoresume_device(udev); - -#endif - /* For the present, all devices default to USB-PERSIST enabled */ #if 0 /* was: #ifdef CONFIG_PM */ /* Hubs are automatically enabled for USB-PERSIST */ diff --git a/drivers/usb/core/sysfs.c b/drivers/usb/core/sysfs.c index 448f5b47fc48..6781c369ce2d 100644 --- a/drivers/usb/core/sysfs.c +++ b/drivers/usb/core/sysfs.c @@ -233,8 +233,6 @@ static DEVICE_ATTR(urbnum, S_IRUGO, show_urbnum, NULL); #ifdef CONFIG_PM -static const char power_group[] = "power"; - static ssize_t show_persist(struct device *dev, struct device_attribute *attr, char *buf) { @@ -278,7 +276,7 @@ static int add_persist_attributes(struct device *dev) if (udev->descriptor.bDeviceClass != USB_CLASS_HUB) rc = sysfs_add_file_to_group(&dev->kobj, &dev_attr_persist.attr, - power_group); + power_group_name); } return rc; } @@ -287,7 +285,7 @@ static void remove_persist_attributes(struct device *dev) { sysfs_remove_file_from_group(&dev->kobj, &dev_attr_persist.attr, - power_group); + power_group_name); } #else @@ -336,44 +334,20 @@ static DEVICE_ATTR(active_duration, S_IRUGO, show_active_duration, NULL); static ssize_t show_autosuspend(struct device *dev, struct device_attribute *attr, char *buf) { - struct usb_device *udev = to_usb_device(dev); - - return sprintf(buf, "%d\n", udev->autosuspend_delay / HZ); + return sprintf(buf, "%d\n", dev->power.autosuspend_delay / 1000); } static ssize_t set_autosuspend(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) { - struct usb_device *udev = to_usb_device(dev); - int value, old_delay; - int rc; + int value; - if (sscanf(buf, "%d", &value) != 1 || value >= INT_MAX/HZ || - value <= - INT_MAX/HZ) + if (sscanf(buf, "%d", &value) != 1 || value >= INT_MAX/1000 || + value <= -INT_MAX/1000) return -EINVAL; - value *= HZ; - - usb_lock_device(udev); - old_delay = udev->autosuspend_delay; - udev->autosuspend_delay = value; - - if (old_delay < 0) { /* Autosuspend wasn't allowed */ - if (value >= 0) - usb_autosuspend_device(udev); - } else { /* Autosuspend was allowed */ - if (value < 0) { - rc = usb_autoresume_device(udev); - if (rc < 0) { - count = rc; - udev->autosuspend_delay = old_delay; - } - } else { - usb_try_autosuspend_device(udev); - } - } - usb_unlock_device(udev); + pm_runtime_set_autosuspend_delay(dev, value * 1000); return count; } @@ -438,44 +412,30 @@ set_level(struct device *dev, struct device_attribute *attr, static DEVICE_ATTR(level, S_IRUGO | S_IWUSR, show_level, set_level); +static struct attribute *power_attrs[] = { + &dev_attr_autosuspend.attr, + &dev_attr_level.attr, + &dev_attr_connected_duration.attr, + &dev_attr_active_duration.attr, + NULL, +}; +static struct attribute_group power_attr_group = { + .name = power_group_name, + .attrs = power_attrs, +}; + static int add_power_attributes(struct device *dev) { int rc = 0; - if (is_usb_device(dev)) { - rc = sysfs_add_file_to_group(&dev->kobj, - &dev_attr_autosuspend.attr, - power_group); - if (rc == 0) - rc = sysfs_add_file_to_group(&dev->kobj, - &dev_attr_level.attr, - power_group); - if (rc == 0) - rc = sysfs_add_file_to_group(&dev->kobj, - &dev_attr_connected_duration.attr, - power_group); - if (rc == 0) - rc = sysfs_add_file_to_group(&dev->kobj, - &dev_attr_active_duration.attr, - power_group); - } + if (is_usb_device(dev)) + rc = sysfs_merge_group(&dev->kobj, &power_attr_group); return rc; } static void remove_power_attributes(struct device *dev) { - sysfs_remove_file_from_group(&dev->kobj, - &dev_attr_active_duration.attr, - power_group); - sysfs_remove_file_from_group(&dev->kobj, - &dev_attr_connected_duration.attr, - power_group); - sysfs_remove_file_from_group(&dev->kobj, - &dev_attr_level.attr, - power_group); - sysfs_remove_file_from_group(&dev->kobj, - &dev_attr_autosuspend.attr, - power_group); + sysfs_unmerge_group(&dev->kobj, &power_attr_group); } #else diff --git a/drivers/usb/core/usb.c b/drivers/usb/core/usb.c index fdd4130fbb7d..079cb57bab4f 100644 --- a/drivers/usb/core/usb.c +++ b/drivers/usb/core/usb.c @@ -445,7 +445,8 @@ struct usb_device *usb_alloc_dev(struct usb_device *parent, INIT_LIST_HEAD(&dev->filelist); #ifdef CONFIG_PM - dev->autosuspend_delay = usb_autosuspend_delay * HZ; + pm_runtime_set_autosuspend_delay(&dev->dev, + usb_autosuspend_delay * 1000); dev->connect_time = jiffies; dev->active_duration = -jiffies; #endif diff --git a/drivers/usb/core/usb.h b/drivers/usb/core/usb.h index cd882203ad34..b975450f403e 100644 --- a/drivers/usb/core/usb.h +++ b/drivers/usb/core/usb.h @@ -75,14 +75,12 @@ static inline int usb_port_resume(struct usb_device *udev, pm_message_t msg) #ifdef CONFIG_USB_SUSPEND extern void usb_autosuspend_device(struct usb_device *udev); -extern void usb_try_autosuspend_device(struct usb_device *udev); extern int usb_autoresume_device(struct usb_device *udev); extern int usb_remote_wakeup(struct usb_device *dev); #else #define usb_autosuspend_device(udev) do {} while (0) -#define usb_try_autosuspend_device(udev) do {} while (0) static inline int usb_autoresume_device(struct usb_device *udev) { return 0; diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig index 607d0db4a988..1dc9739277b4 100644 --- a/drivers/usb/gadget/Kconfig +++ b/drivers/usb/gadget/Kconfig @@ -338,6 +338,19 @@ config USB_S3C2410_DEBUG boolean "S3C2410 udc debug messages" depends on USB_GADGET_S3C2410 +config USB_GADGET_PXA_U2O + boolean "PXA9xx Processor USB2.0 controller" + select USB_GADGET_DUALSPEED + help + PXA9xx Processor series include a high speed USB2.0 device + controller, which support high speed and full speed USB peripheral. + +config USB_PXA_U2O + tristate + depends on USB_GADGET_PXA_U2O + default USB_GADGET + select USB_GADGET_SELECTED + # # Controllers available in both integrated and discrete versions # @@ -414,8 +427,8 @@ config USB_FSL_QE default USB_GADGET select USB_GADGET_SELECTED -config USB_GADGET_CI13XXX - boolean "MIPS USB CI13xxx" +config USB_GADGET_CI13XXX_PCI + boolean "MIPS USB CI13xxx PCI UDC" depends on PCI select USB_GADGET_DUALSPEED help @@ -426,9 +439,9 @@ config USB_GADGET_CI13XXX dynamically linked module called "ci13xxx_udc" and force all gadget drivers to also be dynamically linked. -config USB_CI13XXX +config USB_CI13XXX_PCI tristate - depends on USB_GADGET_CI13XXX + depends on USB_GADGET_CI13XXX_PCI default USB_GADGET select USB_GADGET_SELECTED @@ -495,6 +508,49 @@ config USB_LANGWELL default USB_GADGET select USB_GADGET_SELECTED +config USB_GADGET_EG20T + boolean "Intel EG20T(Topcliff) USB Device controller" + depends on PCI + select USB_GADGET_DUALSPEED + help + This is a USB device driver for EG20T PCH. + EG20T PCH is the platform controller hub that is used in Intel's + general embedded platform. EG20T PCH has USB device interface. + Using this interface, it is able to access system devices connected + to USB device. + This driver enables USB device function. + USB device is a USB peripheral controller which + supports both full and high speed USB 2.0 data transfers. + This driver supports both control transfer and bulk transfer modes. + This driver dose not support interrupt transfer or isochronous + transfer modes. + +config USB_EG20T + tristate + depends on USB_GADGET_EG20T + default USB_GADGET + select USB_GADGET_SELECTED + +config USB_GADGET_CI13XXX_MSM + boolean "MIPS USB CI13xxx for MSM" + depends on ARCH_MSM + select USB_GADGET_DUALSPEED + select USB_MSM_OTG_72K + help + MSM SoC has chipidea USB controller. This driver uses + ci13xxx_udc core. + This driver depends on OTG driver for PHY initialization, + clock management, powering up VBUS, and power management. + + Say "y" to link the driver statically, or "m" to build a + dynamically linked module called "ci13xxx_msm" and force all + gadget drivers to also be dynamically linked. + +config USB_CI13XXX_MSM + tristate + depends on USB_GADGET_CI13XXX_MSM + default USB_GADGET + select USB_GADGET_SELECTED # # LAST -- dummy/emulated controller @@ -685,6 +741,19 @@ config USB_ETH_EEM If you say "y" here, the Ethernet gadget driver will use the EEM protocol rather than ECM. If unsure, say "n". +config USB_G_NCM + tristate "Network Control Model (NCM) support" + depends on NET + select CRC32 + help + This driver implements USB CDC NCM subclass standard. NCM is + an advanced protocol for Ethernet encapsulation, allows grouping + of several ethernet frames into one USB transfer and diffferent + alignment possibilities. + + Say "y" to link the driver statically, or "m" to build a + dynamically linked module called "g_ncm". + config USB_GADGETFS tristate "Gadget Filesystem (EXPERIMENTAL)" depends on EXPERIMENTAL diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile index 5780db42417b..55f5e8ae5924 100644 --- a/drivers/usb/gadget/Makefile +++ b/drivers/usb/gadget/Makefile @@ -21,9 +21,13 @@ fsl_usb2_udc-$(CONFIG_ARCH_MXC) += fsl_mxc_udc.o obj-$(CONFIG_USB_M66592) += m66592-udc.o obj-$(CONFIG_USB_R8A66597) += r8a66597-udc.o obj-$(CONFIG_USB_FSL_QE) += fsl_qe_udc.o -obj-$(CONFIG_USB_CI13XXX) += ci13xxx_udc.o +obj-$(CONFIG_USB_CI13XXX_PCI) += ci13xxx_pci.o obj-$(CONFIG_USB_S3C_HSOTG) += s3c-hsotg.o obj-$(CONFIG_USB_LANGWELL) += langwell_udc.o +obj-$(CONFIG_USB_EG20T) += pch_udc.o +obj-$(CONFIG_USB_PXA_U2O) += mv_udc.o +mv_udc-y := mv_udc_core.o mv_udc_phy.o +obj-$(CONFIG_USB_CI13XXX_MSM) += ci13xxx_msm.o # # USB gadget drivers @@ -43,6 +47,7 @@ g_hid-y := hid.o g_dbgp-y := dbgp.o g_nokia-y := nokia.o g_webcam-y := webcam.o +g_ncm-y := ncm.o obj-$(CONFIG_USB_ZERO) += g_zero.o obj-$(CONFIG_USB_AUDIO) += g_audio.o @@ -60,3 +65,4 @@ obj-$(CONFIG_USB_G_DBGP) += g_dbgp.o obj-$(CONFIG_USB_G_MULTI) += g_multi.o obj-$(CONFIG_USB_G_NOKIA) += g_nokia.o obj-$(CONFIG_USB_G_WEBCAM) += g_webcam.o +obj-$(CONFIG_USB_G_NCM) += g_ncm.o diff --git a/drivers/usb/gadget/amd5536udc.c b/drivers/usb/gadget/amd5536udc.c index 9034e0344723..f8dd7269d79c 100644 --- a/drivers/usb/gadget/amd5536udc.c +++ b/drivers/usb/gadget/amd5536udc.c @@ -3359,7 +3359,6 @@ static int udc_probe(struct udc *dev) dev_set_name(&dev->gadget.dev, "gadget"); dev->gadget.dev.release = gadget_release; dev->gadget.name = name; - dev->gadget.name = name; dev->gadget.is_dualspeed = 1; /* init registers, interrupts, ... */ diff --git a/drivers/usb/gadget/ci13xxx_msm.c b/drivers/usb/gadget/ci13xxx_msm.c new file mode 100644 index 000000000000..139ac9419597 --- /dev/null +++ b/drivers/usb/gadget/ci13xxx_msm.c @@ -0,0 +1,134 @@ +/* Copyright (c) 2010, Code Aurora Forum. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA + * 02110-1301, USA. + * + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/pm_runtime.h> +#include <linux/usb/msm_hsusb_hw.h> +#include <linux/usb/ulpi.h> + +#include "ci13xxx_udc.c" + +#define MSM_USB_BASE (udc->regs) + +static irqreturn_t msm_udc_irq(int irq, void *data) +{ + return udc_irq(); +} + +static void ci13xxx_msm_notify_event(struct ci13xxx *udc, unsigned event) +{ + struct device *dev = udc->gadget.dev.parent; + int val; + + switch (event) { + case CI13XXX_CONTROLLER_RESET_EVENT: + dev_dbg(dev, "CI13XXX_CONTROLLER_RESET_EVENT received\n"); + writel(0, USB_AHBBURST); + writel(0, USB_AHBMODE); + break; + case CI13XXX_CONTROLLER_STOPPED_EVENT: + dev_dbg(dev, "CI13XXX_CONTROLLER_STOPPED_EVENT received\n"); + /* + * Put the transceiver in non-driving mode. Otherwise host + * may not detect soft-disconnection. + */ + val = otg_io_read(udc->transceiver, ULPI_FUNC_CTRL); + val &= ~ULPI_FUNC_CTRL_OPMODE_MASK; + val |= ULPI_FUNC_CTRL_OPMODE_NONDRIVING; + otg_io_write(udc->transceiver, val, ULPI_FUNC_CTRL); + break; + default: + dev_dbg(dev, "unknown ci13xxx_udc event\n"); + break; + } +} + +static struct ci13xxx_udc_driver ci13xxx_msm_udc_driver = { + .name = "ci13xxx_msm", + .flags = CI13XXX_REGS_SHARED | + CI13XXX_REQUIRE_TRANSCEIVER | + CI13XXX_PULLUP_ON_VBUS | + CI13XXX_DISABLE_STREAMING, + + .notify_event = ci13xxx_msm_notify_event, +}; + +static int ci13xxx_msm_probe(struct platform_device *pdev) +{ + struct resource *res; + void __iomem *regs; + int irq; + int ret; + + dev_dbg(&pdev->dev, "ci13xxx_msm_probe\n"); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "failed to get platform resource mem\n"); + return -ENXIO; + } + + regs = ioremap(res->start, resource_size(res)); + if (!regs) { + dev_err(&pdev->dev, "ioremap failed\n"); + return -ENOMEM; + } + + ret = udc_probe(&ci13xxx_msm_udc_driver, &pdev->dev, regs); + if (ret < 0) { + dev_err(&pdev->dev, "udc_probe failed\n"); + goto iounmap; + } + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(&pdev->dev, "IRQ not found\n"); + ret = -ENXIO; + goto udc_remove; + } + + ret = request_irq(irq, msm_udc_irq, IRQF_SHARED, pdev->name, pdev); + if (ret < 0) { + dev_err(&pdev->dev, "request_irq failed\n"); + goto udc_remove; + } + + pm_runtime_no_callbacks(&pdev->dev); + pm_runtime_enable(&pdev->dev); + + return 0; + +udc_remove: + udc_remove(); +iounmap: + iounmap(regs); + + return ret; +} + +static struct platform_driver ci13xxx_msm_driver = { + .probe = ci13xxx_msm_probe, + .driver = { .name = "msm_hsusb", }, +}; + +static int __init ci13xxx_msm_init(void) +{ + return platform_driver_register(&ci13xxx_msm_driver); +} +module_init(ci13xxx_msm_init); diff --git a/drivers/usb/gadget/ci13xxx_pci.c b/drivers/usb/gadget/ci13xxx_pci.c new file mode 100644 index 000000000000..883ab5e832d1 --- /dev/null +++ b/drivers/usb/gadget/ci13xxx_pci.c @@ -0,0 +1,176 @@ +/* + * ci13xxx_pci.c - MIPS USB IP core family device controller + * + * Copyright (C) 2008 Chipidea - MIPS Technologies, Inc. All rights reserved. + * + * Author: David Lopo + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/pci.h> + +#include "ci13xxx_udc.c" + +/* driver name */ +#define UDC_DRIVER_NAME "ci13xxx_pci" + +/****************************************************************************** + * PCI block + *****************************************************************************/ +/** + * ci13xxx_pci_irq: interrut handler + * @irq: irq number + * @pdev: USB Device Controller interrupt source + * + * This function returns IRQ_HANDLED if the IRQ has been handled + * This is an ISR don't trace, use attribute interface instead + */ +static irqreturn_t ci13xxx_pci_irq(int irq, void *pdev) +{ + if (irq == 0) { + dev_err(&((struct pci_dev *)pdev)->dev, "Invalid IRQ0 usage!"); + return IRQ_HANDLED; + } + return udc_irq(); +} + +static struct ci13xxx_udc_driver ci13xxx_pci_udc_driver = { + .name = UDC_DRIVER_NAME, +}; + +/** + * ci13xxx_pci_probe: PCI probe + * @pdev: USB device controller being probed + * @id: PCI hotplug ID connecting controller to UDC framework + * + * This function returns an error code + * Allocates basic PCI resources for this USB device controller, and then + * invokes the udc_probe() method to start the UDC associated with it + */ +static int __devinit ci13xxx_pci_probe(struct pci_dev *pdev, + const struct pci_device_id *id) +{ + void __iomem *regs = NULL; + int retval = 0; + + if (id == NULL) + return -EINVAL; + + retval = pci_enable_device(pdev); + if (retval) + goto done; + + if (!pdev->irq) { + dev_err(&pdev->dev, "No IRQ, check BIOS/PCI setup!"); + retval = -ENODEV; + goto disable_device; + } + + retval = pci_request_regions(pdev, UDC_DRIVER_NAME); + if (retval) + goto disable_device; + + /* BAR 0 holds all the registers */ + regs = pci_iomap(pdev, 0, 0); + if (!regs) { + dev_err(&pdev->dev, "Error mapping memory!"); + retval = -EFAULT; + goto release_regions; + } + pci_set_drvdata(pdev, (__force void *)regs); + + pci_set_master(pdev); + pci_try_set_mwi(pdev); + + retval = udc_probe(&ci13xxx_pci_udc_driver, &pdev->dev, regs); + if (retval) + goto iounmap; + + /* our device does not have MSI capability */ + + retval = request_irq(pdev->irq, ci13xxx_pci_irq, IRQF_SHARED, + UDC_DRIVER_NAME, pdev); + if (retval) + goto gadget_remove; + + return 0; + + gadget_remove: + udc_remove(); + iounmap: + pci_iounmap(pdev, regs); + release_regions: + pci_release_regions(pdev); + disable_device: + pci_disable_device(pdev); + done: + return retval; +} + +/** + * ci13xxx_pci_remove: PCI remove + * @pdev: USB Device Controller being removed + * + * Reverses the effect of ci13xxx_pci_probe(), + * first invoking the udc_remove() and then releases + * all PCI resources allocated for this USB device controller + */ +static void __devexit ci13xxx_pci_remove(struct pci_dev *pdev) +{ + free_irq(pdev->irq, pdev); + udc_remove(); + pci_iounmap(pdev, (__force void __iomem *)pci_get_drvdata(pdev)); + pci_release_regions(pdev); + pci_disable_device(pdev); +} + +/** + * PCI device table + * PCI device structure + * + * Check "pci.h" for details + */ +static DEFINE_PCI_DEVICE_TABLE(ci13xxx_pci_id_table) = { + { PCI_DEVICE(0x153F, 0x1004) }, + { PCI_DEVICE(0x153F, 0x1006) }, + { 0, 0, 0, 0, 0, 0, 0 /* end: all zeroes */ } +}; +MODULE_DEVICE_TABLE(pci, ci13xxx_pci_id_table); + +static struct pci_driver ci13xxx_pci_driver = { + .name = UDC_DRIVER_NAME, + .id_table = ci13xxx_pci_id_table, + .probe = ci13xxx_pci_probe, + .remove = __devexit_p(ci13xxx_pci_remove), +}; + +/** + * ci13xxx_pci_init: module init + * + * Driver load + */ +static int __init ci13xxx_pci_init(void) +{ + return pci_register_driver(&ci13xxx_pci_driver); +} +module_init(ci13xxx_pci_init); + +/** + * ci13xxx_pci_exit: module exit + * + * Driver unload + */ +static void __exit ci13xxx_pci_exit(void) +{ + pci_unregister_driver(&ci13xxx_pci_driver); +} +module_exit(ci13xxx_pci_exit); + +MODULE_AUTHOR("MIPS - David Lopo <dlopo@chipidea.mips.com>"); +MODULE_DESCRIPTION("MIPS CI13XXX USB Peripheral Controller"); +MODULE_LICENSE("GPL"); +MODULE_VERSION("June 2008"); diff --git a/drivers/usb/gadget/ci13xxx_udc.c b/drivers/usb/gadget/ci13xxx_udc.c index 98b36fc88c77..f200e472e476 100644 --- a/drivers/usb/gadget/ci13xxx_udc.c +++ b/drivers/usb/gadget/ci13xxx_udc.c @@ -22,7 +22,6 @@ * - ENDPT: endpoint operations (Gadget API) * - GADGET: gadget operations (Gadget API) * - BUS: bus glue code, bus abstraction layer - * - PCI: PCI core interface and PCI resources (interrupts, memory...) * * Compile Options * - CONFIG_USB_GADGET_DEBUG_FILES: enable debug facilities @@ -60,11 +59,11 @@ #include <linux/io.h> #include <linux/irq.h> #include <linux/kernel.h> -#include <linux/module.h> -#include <linux/pci.h> #include <linux/slab.h> +#include <linux/pm_runtime.h> #include <linux/usb/ch9.h> #include <linux/usb/gadget.h> +#include <linux/usb/otg.h> #include "ci13xxx_udc.h" @@ -75,9 +74,6 @@ /* ctrl register bank access */ static DEFINE_SPINLOCK(udc_lock); -/* driver name */ -#define UDC_DRIVER_NAME "ci13xxx_udc" - /* control endpoint description */ static const struct usb_endpoint_descriptor ctrl_endpt_desc = { @@ -132,6 +128,9 @@ static struct { size_t size; /* bank size */ } hw_bank; +/* MSM specific */ +#define ABS_AHBBURST (0x0090UL) +#define ABS_AHBMODE (0x0098UL) /* UDC register map */ #define ABS_CAPLENGTH (0x100UL) #define ABS_HCCPARAMS (0x108UL) @@ -248,13 +247,7 @@ static u32 hw_ctest_and_write(u32 addr, u32 mask, u32 data) return (reg & mask) >> ffs_nr(mask); } -/** - * hw_device_reset: resets chip (execute without interruption) - * @base: register base address - * - * This function returns an error code - */ -static int hw_device_reset(void __iomem *base) +static int hw_device_init(void __iomem *base) { u32 reg; @@ -271,6 +264,28 @@ static int hw_device_reset(void __iomem *base) hw_bank.size += CAP_LAST; hw_bank.size /= sizeof(u32); + reg = hw_aread(ABS_DCCPARAMS, DCCPARAMS_DEN) >> ffs_nr(DCCPARAMS_DEN); + if (reg == 0 || reg > ENDPT_MAX) + return -ENODEV; + + hw_ep_max = reg; /* cache hw ENDPT_MAX */ + + /* setup lock mode ? */ + + /* ENDPTSETUPSTAT is '0' by default */ + + /* HCSPARAMS.bf.ppc SHOULD BE zero for device */ + + return 0; +} +/** + * hw_device_reset: resets chip (execute without interruption) + * @base: register base address + * + * This function returns an error code + */ +static int hw_device_reset(struct ci13xxx *udc) +{ /* should flush & stop before reset */ hw_cwrite(CAP_ENDPTFLUSH, ~0, ~0); hw_cwrite(CAP_USBCMD, USBCMD_RS, 0); @@ -279,6 +294,14 @@ static int hw_device_reset(void __iomem *base) while (hw_cread(CAP_USBCMD, USBCMD_RST)) udelay(10); /* not RTOS friendly */ + + if (udc->udc_driver->notify_event) + udc->udc_driver->notify_event(udc, + CI13XXX_CONTROLLER_RESET_EVENT); + + if (udc->udc_driver->flags && CI13XXX_DISABLE_STREAMING) + hw_cwrite(CAP_USBMODE, USBMODE_SDIS, USBMODE_SDIS); + /* USBMODE should be configured step by step */ hw_cwrite(CAP_USBMODE, USBMODE_CM, USBMODE_CM_IDLE); hw_cwrite(CAP_USBMODE, USBMODE_CM, USBMODE_CM_DEVICE); @@ -290,18 +313,6 @@ static int hw_device_reset(void __iomem *base) return -ENODEV; } - reg = hw_aread(ABS_DCCPARAMS, DCCPARAMS_DEN) >> ffs_nr(DCCPARAMS_DEN); - if (reg == 0 || reg > ENDPT_MAX) - return -ENODEV; - - hw_ep_max = reg; /* cache hw ENDPT_MAX */ - - /* setup lock mode ? */ - - /* ENDPTSETUPSTAT is '0' by default */ - - /* HCSPARAMS.bf.ppc SHOULD BE zero for device */ - return 0; } @@ -1557,8 +1568,6 @@ __acquires(mEp->lock) * Caller must hold lock */ static int _gadget_stop_activity(struct usb_gadget *gadget) -__releases(udc->lock) -__acquires(udc->lock) { struct usb_ep *ep; struct ci13xxx *udc = container_of(gadget, struct ci13xxx, gadget); @@ -1570,8 +1579,6 @@ __acquires(udc->lock) if (gadget == NULL) return -EINVAL; - spin_unlock(udc->lock); - /* flush all endpoints */ gadget_for_each_ep(ep, gadget) { usb_ep_fifo_flush(ep); @@ -1591,8 +1598,6 @@ __acquires(udc->lock) mEp->status = NULL; } - spin_lock(udc->lock); - return 0; } @@ -1621,6 +1626,7 @@ __acquires(udc->lock) dbg_event(0xFF, "BUS RST", 0); + spin_unlock(udc->lock); retval = _gadget_stop_activity(&udc->gadget); if (retval) goto done; @@ -1629,10 +1635,9 @@ __acquires(udc->lock) if (retval) goto done; - spin_unlock(udc->lock); retval = usb_ep_enable(&mEp->ep, &ctrl_endpt_desc); if (!retval) { - mEp->status = usb_ep_alloc_request(&mEp->ep, GFP_KERNEL); + mEp->status = usb_ep_alloc_request(&mEp->ep, GFP_ATOMIC); if (mEp->status == NULL) { usb_ep_disable(&mEp->ep); retval = -ENOMEM; @@ -2061,7 +2066,6 @@ static struct usb_request *ep_alloc_request(struct usb_ep *ep, gfp_t gfp_flags) { struct ci13xxx_ep *mEp = container_of(ep, struct ci13xxx_ep, ep); struct ci13xxx_req *mReq = NULL; - unsigned long flags; trace("%p, %i", ep, gfp_flags); @@ -2070,8 +2074,6 @@ static struct usb_request *ep_alloc_request(struct usb_ep *ep, gfp_t gfp_flags) return NULL; } - spin_lock_irqsave(mEp->lock, flags); - mReq = kzalloc(sizeof(struct ci13xxx_req), gfp_flags); if (mReq != NULL) { INIT_LIST_HEAD(&mReq->queue); @@ -2086,8 +2088,6 @@ static struct usb_request *ep_alloc_request(struct usb_ep *ep, gfp_t gfp_flags) dbg_event(_usb_addr(mEp), "ALLOC", mReq == NULL); - spin_unlock_irqrestore(mEp->lock, flags); - return (mReq == NULL) ? NULL : &mReq->req; } @@ -2332,12 +2332,47 @@ static const struct usb_ep_ops usb_ep_ops = { /****************************************************************************** * GADGET block *****************************************************************************/ +static int ci13xxx_vbus_session(struct usb_gadget *_gadget, int is_active) +{ + struct ci13xxx *udc = container_of(_gadget, struct ci13xxx, gadget); + unsigned long flags; + int gadget_ready = 0; + + if (!(udc->udc_driver->flags & CI13XXX_PULLUP_ON_VBUS)) + return -EOPNOTSUPP; + + spin_lock_irqsave(udc->lock, flags); + udc->vbus_active = is_active; + if (udc->driver) + gadget_ready = 1; + spin_unlock_irqrestore(udc->lock, flags); + + if (gadget_ready) { + if (is_active) { + pm_runtime_get_sync(&_gadget->dev); + hw_device_reset(udc); + hw_device_state(udc->ci13xxx_ep[0].qh[RX].dma); + } else { + hw_device_state(0); + if (udc->udc_driver->notify_event) + udc->udc_driver->notify_event(udc, + CI13XXX_CONTROLLER_STOPPED_EVENT); + _gadget_stop_activity(&udc->gadget); + pm_runtime_put_sync(&_gadget->dev); + } + } + + return 0; +} + /** * Device operations part of the API to the USB controller hardware, * which don't involve endpoints (or i/o) * Check "usb_gadget.h" for details */ -static const struct usb_gadget_ops usb_gadget_ops; +static const struct usb_gadget_ops usb_gadget_ops = { + .vbus_session = ci13xxx_vbus_session, +}; /** * usb_gadget_probe_driver: register a gadget driver @@ -2390,7 +2425,6 @@ int usb_gadget_probe_driver(struct usb_gadget_driver *driver, info("hw_ep_max = %d", hw_ep_max); udc->driver = driver; - udc->gadget.ops = NULL; udc->gadget.dev.driver = NULL; retval = 0; @@ -2410,9 +2444,11 @@ int usb_gadget_probe_driver(struct usb_gadget_driver *driver, /* this allocation cannot be random */ for (k = RX; k <= TX; k++) { INIT_LIST_HEAD(&mEp->qh[k].queue); + spin_unlock_irqrestore(udc->lock, flags); mEp->qh[k].ptr = dma_pool_alloc(udc->qh_pool, GFP_KERNEL, &mEp->qh[k].dma); + spin_lock_irqsave(udc->lock, flags); if (mEp->qh[k].ptr == NULL) retval = -ENOMEM; else @@ -2429,7 +2465,6 @@ int usb_gadget_probe_driver(struct usb_gadget_driver *driver, /* bind gadget */ driver->driver.bus = NULL; - udc->gadget.ops = &usb_gadget_ops; udc->gadget.dev.driver = &driver->driver; spin_unlock_irqrestore(udc->lock, flags); @@ -2437,12 +2472,24 @@ int usb_gadget_probe_driver(struct usb_gadget_driver *driver, spin_lock_irqsave(udc->lock, flags); if (retval) { - udc->gadget.ops = NULL; udc->gadget.dev.driver = NULL; goto done; } + pm_runtime_get_sync(&udc->gadget.dev); + if (udc->udc_driver->flags & CI13XXX_PULLUP_ON_VBUS) { + if (udc->vbus_active) { + if (udc->udc_driver->flags & CI13XXX_REGS_SHARED) + hw_device_reset(udc); + } else { + pm_runtime_put_sync(&udc->gadget.dev); + goto done; + } + } + retval = hw_device_state(udc->ci13xxx_ep[0].qh[RX].dma); + if (retval) + pm_runtime_put_sync(&udc->gadget.dev); done: spin_unlock_irqrestore(udc->lock, flags); @@ -2475,19 +2522,22 @@ int usb_gadget_unregister_driver(struct usb_gadget_driver *driver) spin_lock_irqsave(udc->lock, flags); - hw_device_state(0); - - /* unbind gadget */ - if (udc->gadget.ops != NULL) { + if (!(udc->udc_driver->flags & CI13XXX_PULLUP_ON_VBUS) || + udc->vbus_active) { + hw_device_state(0); + if (udc->udc_driver->notify_event) + udc->udc_driver->notify_event(udc, + CI13XXX_CONTROLLER_STOPPED_EVENT); _gadget_stop_activity(&udc->gadget); + pm_runtime_put(&udc->gadget.dev); + } - spin_unlock_irqrestore(udc->lock, flags); - driver->unbind(&udc->gadget); /* MAY SLEEP */ - spin_lock_irqsave(udc->lock, flags); + /* unbind gadget */ + spin_unlock_irqrestore(udc->lock, flags); + driver->unbind(&udc->gadget); /* MAY SLEEP */ + spin_lock_irqsave(udc->lock, flags); - udc->gadget.ops = NULL; - udc->gadget.dev.driver = NULL; - } + udc->gadget.dev.driver = NULL; /* free resources */ for (i = 0; i < hw_ep_max; i++) { @@ -2544,6 +2594,14 @@ static irqreturn_t udc_irq(void) } spin_lock(udc->lock); + + if (udc->udc_driver->flags & CI13XXX_REGS_SHARED) { + if (hw_cread(CAP_USBMODE, USBMODE_CM) != + USBMODE_CM_DEVICE) { + spin_unlock(udc->lock); + return IRQ_NONE; + } + } intr = hw_test_and_clear_intr_active(); if (intr) { isr_statistics.hndl.buf[isr_statistics.hndl.idx++] = intr; @@ -2602,14 +2660,16 @@ static void udc_release(struct device *dev) * No interrupts active, the IRQ has not been requested yet * Kernel assumes 32-bit DMA operations by default, no need to dma_set_mask */ -static int udc_probe(struct device *dev, void __iomem *regs, const char *name) +static int udc_probe(struct ci13xxx_udc_driver *driver, struct device *dev, + void __iomem *regs) { struct ci13xxx *udc; int retval = 0; trace("%p, %p, %p", dev, regs, name); - if (dev == NULL || regs == NULL || name == NULL) + if (dev == NULL || regs == NULL || driver == NULL || + driver->name == NULL) return -EINVAL; udc = kzalloc(sizeof(struct ci13xxx), GFP_KERNEL); @@ -2617,42 +2677,77 @@ static int udc_probe(struct device *dev, void __iomem *regs, const char *name) return -ENOMEM; udc->lock = &udc_lock; + udc->regs = regs; + udc->udc_driver = driver; - retval = hw_device_reset(regs); - if (retval) - goto done; - - udc->gadget.ops = NULL; + udc->gadget.ops = &usb_gadget_ops; udc->gadget.speed = USB_SPEED_UNKNOWN; udc->gadget.is_dualspeed = 1; udc->gadget.is_otg = 0; - udc->gadget.name = name; + udc->gadget.name = driver->name; INIT_LIST_HEAD(&udc->gadget.ep_list); udc->gadget.ep0 = NULL; dev_set_name(&udc->gadget.dev, "gadget"); udc->gadget.dev.dma_mask = dev->dma_mask; + udc->gadget.dev.coherent_dma_mask = dev->coherent_dma_mask; udc->gadget.dev.parent = dev; udc->gadget.dev.release = udc_release; + retval = hw_device_init(regs); + if (retval < 0) + goto free_udc; + + udc->transceiver = otg_get_transceiver(); + + if (udc->udc_driver->flags & CI13XXX_REQUIRE_TRANSCEIVER) { + if (udc->transceiver == NULL) { + retval = -ENODEV; + goto free_udc; + } + } + + if (!(udc->udc_driver->flags & CI13XXX_REGS_SHARED)) { + retval = hw_device_reset(udc); + if (retval) + goto put_transceiver; + } + retval = device_register(&udc->gadget.dev); - if (retval) - goto done; + if (retval) { + put_device(&udc->gadget.dev); + goto put_transceiver; + } #ifdef CONFIG_USB_GADGET_DEBUG_FILES retval = dbg_create_files(&udc->gadget.dev); #endif - if (retval) { - device_unregister(&udc->gadget.dev); - goto done; + if (retval) + goto unreg_device; + + if (udc->transceiver) { + retval = otg_set_peripheral(udc->transceiver, &udc->gadget); + if (retval) + goto remove_dbg; } + pm_runtime_no_callbacks(&udc->gadget.dev); + pm_runtime_enable(&udc->gadget.dev); _udc = udc; return retval; - done: err("error = %i", retval); +remove_dbg: +#ifdef CONFIG_USB_GADGET_DEBUG_FILES + dbg_remove_files(&udc->gadget.dev); +#endif +unreg_device: + device_unregister(&udc->gadget.dev); +put_transceiver: + if (udc->transceiver) + otg_put_transceiver(udc->transceiver); +free_udc: kfree(udc); _udc = NULL; return retval; @@ -2672,6 +2767,10 @@ static void udc_remove(void) return; } + if (udc->transceiver) { + otg_set_peripheral(udc->transceiver, &udc->gadget); + otg_put_transceiver(udc->transceiver); + } #ifdef CONFIG_USB_GADGET_DEBUG_FILES dbg_remove_files(&udc->gadget.dev); #endif @@ -2680,156 +2779,3 @@ static void udc_remove(void) kfree(udc); _udc = NULL; } - -/****************************************************************************** - * PCI block - *****************************************************************************/ -/** - * ci13xxx_pci_irq: interrut handler - * @irq: irq number - * @pdev: USB Device Controller interrupt source - * - * This function returns IRQ_HANDLED if the IRQ has been handled - * This is an ISR don't trace, use attribute interface instead - */ -static irqreturn_t ci13xxx_pci_irq(int irq, void *pdev) -{ - if (irq == 0) { - dev_err(&((struct pci_dev *)pdev)->dev, "Invalid IRQ0 usage!"); - return IRQ_HANDLED; - } - return udc_irq(); -} - -/** - * ci13xxx_pci_probe: PCI probe - * @pdev: USB device controller being probed - * @id: PCI hotplug ID connecting controller to UDC framework - * - * This function returns an error code - * Allocates basic PCI resources for this USB device controller, and then - * invokes the udc_probe() method to start the UDC associated with it - */ -static int __devinit ci13xxx_pci_probe(struct pci_dev *pdev, - const struct pci_device_id *id) -{ - void __iomem *regs = NULL; - int retval = 0; - - if (id == NULL) - return -EINVAL; - - retval = pci_enable_device(pdev); - if (retval) - goto done; - - if (!pdev->irq) { - dev_err(&pdev->dev, "No IRQ, check BIOS/PCI setup!"); - retval = -ENODEV; - goto disable_device; - } - - retval = pci_request_regions(pdev, UDC_DRIVER_NAME); - if (retval) - goto disable_device; - - /* BAR 0 holds all the registers */ - regs = pci_iomap(pdev, 0, 0); - if (!regs) { - dev_err(&pdev->dev, "Error mapping memory!"); - retval = -EFAULT; - goto release_regions; - } - pci_set_drvdata(pdev, (__force void *)regs); - - pci_set_master(pdev); - pci_try_set_mwi(pdev); - - retval = udc_probe(&pdev->dev, regs, UDC_DRIVER_NAME); - if (retval) - goto iounmap; - - /* our device does not have MSI capability */ - - retval = request_irq(pdev->irq, ci13xxx_pci_irq, IRQF_SHARED, - UDC_DRIVER_NAME, pdev); - if (retval) - goto gadget_remove; - - return 0; - - gadget_remove: - udc_remove(); - iounmap: - pci_iounmap(pdev, regs); - release_regions: - pci_release_regions(pdev); - disable_device: - pci_disable_device(pdev); - done: - return retval; -} - -/** - * ci13xxx_pci_remove: PCI remove - * @pdev: USB Device Controller being removed - * - * Reverses the effect of ci13xxx_pci_probe(), - * first invoking the udc_remove() and then releases - * all PCI resources allocated for this USB device controller - */ -static void __devexit ci13xxx_pci_remove(struct pci_dev *pdev) -{ - free_irq(pdev->irq, pdev); - udc_remove(); - pci_iounmap(pdev, (__force void __iomem *)pci_get_drvdata(pdev)); - pci_release_regions(pdev); - pci_disable_device(pdev); -} - -/** - * PCI device table - * PCI device structure - * - * Check "pci.h" for details - */ -static DEFINE_PCI_DEVICE_TABLE(ci13xxx_pci_id_table) = { - { PCI_DEVICE(0x153F, 0x1004) }, - { PCI_DEVICE(0x153F, 0x1006) }, - { 0, 0, 0, 0, 0, 0, 0 /* end: all zeroes */ } -}; -MODULE_DEVICE_TABLE(pci, ci13xxx_pci_id_table); - -static struct pci_driver ci13xxx_pci_driver = { - .name = UDC_DRIVER_NAME, - .id_table = ci13xxx_pci_id_table, - .probe = ci13xxx_pci_probe, - .remove = __devexit_p(ci13xxx_pci_remove), -}; - -/** - * ci13xxx_pci_init: module init - * - * Driver load - */ -static int __init ci13xxx_pci_init(void) -{ - return pci_register_driver(&ci13xxx_pci_driver); -} -module_init(ci13xxx_pci_init); - -/** - * ci13xxx_pci_exit: module exit - * - * Driver unload - */ -static void __exit ci13xxx_pci_exit(void) -{ - pci_unregister_driver(&ci13xxx_pci_driver); -} -module_exit(ci13xxx_pci_exit); - -MODULE_AUTHOR("MIPS - David Lopo <dlopo@chipidea.mips.com>"); -MODULE_DESCRIPTION("MIPS CI13XXX USB Peripheral Controller"); -MODULE_LICENSE("GPL"); -MODULE_VERSION("June 2008"); diff --git a/drivers/usb/gadget/ci13xxx_udc.h b/drivers/usb/gadget/ci13xxx_udc.h index 4026e9cede34..4fd19313e238 100644 --- a/drivers/usb/gadget/ci13xxx_udc.h +++ b/drivers/usb/gadget/ci13xxx_udc.h @@ -97,9 +97,24 @@ struct ci13xxx_ep { struct dma_pool *td_pool; }; +struct ci13xxx; +struct ci13xxx_udc_driver { + const char *name; + unsigned long flags; +#define CI13XXX_REGS_SHARED BIT(0) +#define CI13XXX_REQUIRE_TRANSCEIVER BIT(1) +#define CI13XXX_PULLUP_ON_VBUS BIT(2) +#define CI13XXX_DISABLE_STREAMING BIT(3) + +#define CI13XXX_CONTROLLER_RESET_EVENT 0 +#define CI13XXX_CONTROLLER_STOPPED_EVENT 1 + void (*notify_event) (struct ci13xxx *udc, unsigned event); +}; + /* CI13XXX UDC descriptor & global resources */ struct ci13xxx { spinlock_t *lock; /* ctrl register bank access */ + void __iomem *regs; /* registers address space */ struct dma_pool *qh_pool; /* DMA pool for queue heads */ struct dma_pool *td_pool; /* DMA pool for transfer descs */ @@ -108,6 +123,9 @@ struct ci13xxx { struct ci13xxx_ep ci13xxx_ep[ENDPT_MAX]; /* extended endpts */ struct usb_gadget_driver *driver; /* 3rd party gadget driver */ + struct ci13xxx_udc_driver *udc_driver; /* device controller driver */ + int vbus_active; /* is VBUS active */ + struct otg_transceiver *transceiver; /* Transceiver struct */ }; /****************************************************************************** @@ -157,6 +175,7 @@ struct ci13xxx { #define USBMODE_CM_DEVICE (0x02UL << 0) #define USBMODE_CM_HOST (0x03UL << 0) #define USBMODE_SLOM BIT(3) +#define USBMODE_SDIS BIT(4) /* ENDPTCTRL */ #define ENDPTCTRL_RXS BIT(0) diff --git a/drivers/usb/gadget/composite.c b/drivers/usb/gadget/composite.c index 7b5cc16e4a0b..21dc0da36ab7 100644 --- a/drivers/usb/gadget/composite.c +++ b/drivers/usb/gadget/composite.c @@ -1126,7 +1126,7 @@ static int composite_bind(struct usb_gadget *gadget) cdev->desc = *composite->dev; cdev->desc.bMaxPacketSize0 = gadget->ep0->maxpacket; - /* stirng overrides */ + /* string overrides */ if (iManufacturer || !cdev->desc.iManufacturer) { if (!iManufacturer && !composite->iManufacturer && !*composite_manufacturer) @@ -1188,6 +1188,8 @@ composite_suspend(struct usb_gadget *gadget) composite->suspend(cdev); cdev->suspended = 1; + + usb_gadget_vbus_draw(gadget, 2); } static void @@ -1195,6 +1197,7 @@ composite_resume(struct usb_gadget *gadget) { struct usb_composite_dev *cdev = get_gadget_data(gadget); struct usb_function *f; + u8 maxpower; /* REVISIT: should we have config level * suspend/resume callbacks? @@ -1207,6 +1210,11 @@ composite_resume(struct usb_gadget *gadget) if (f->resume) f->resume(f); } + + maxpower = cdev->config->bMaxPower; + + usb_gadget_vbus_draw(gadget, maxpower ? + (2 * maxpower) : CONFIG_USB_GADGET_VBUS_DRAW); } cdev->suspended = 0; diff --git a/drivers/usb/gadget/dummy_hcd.c b/drivers/usb/gadget/dummy_hcd.c index 1d2a2abbfa80..13b9f47feecd 100644 --- a/drivers/usb/gadget/dummy_hcd.c +++ b/drivers/usb/gadget/dummy_hcd.c @@ -1197,6 +1197,139 @@ static struct dummy_ep *find_endpoint (struct dummy *dum, u8 address) #define Ep_Request (USB_TYPE_STANDARD | USB_RECIP_ENDPOINT) #define Ep_InRequest (Ep_Request | USB_DIR_IN) + +/** + * handle_control_request() - handles all control transfers + * @dum: pointer to dummy (the_controller) + * @urb: the urb request to handle + * @setup: pointer to the setup data for a USB device control + * request + * @status: pointer to request handling status + * + * Return 0 - if the request was handled + * 1 - if the request wasn't handles + * error code on error + */ +static int handle_control_request(struct dummy *dum, struct urb *urb, + struct usb_ctrlrequest *setup, + int *status) +{ + struct dummy_ep *ep2; + int ret_val = 1; + unsigned w_index; + unsigned w_value; + + w_index = le16_to_cpu(setup->wIndex); + w_value = le16_to_cpu(setup->wValue); + switch (setup->bRequest) { + case USB_REQ_SET_ADDRESS: + if (setup->bRequestType != Dev_Request) + break; + dum->address = w_value; + *status = 0; + dev_dbg(udc_dev(dum), "set_address = %d\n", + w_value); + ret_val = 0; + break; + case USB_REQ_SET_FEATURE: + if (setup->bRequestType == Dev_Request) { + ret_val = 0; + switch (w_value) { + case USB_DEVICE_REMOTE_WAKEUP: + break; + case USB_DEVICE_B_HNP_ENABLE: + dum->gadget.b_hnp_enable = 1; + break; + case USB_DEVICE_A_HNP_SUPPORT: + dum->gadget.a_hnp_support = 1; + break; + case USB_DEVICE_A_ALT_HNP_SUPPORT: + dum->gadget.a_alt_hnp_support = 1; + break; + default: + ret_val = -EOPNOTSUPP; + } + if (ret_val == 0) { + dum->devstatus |= (1 << w_value); + *status = 0; + } + } else if (setup->bRequestType == Ep_Request) { + /* endpoint halt */ + ep2 = find_endpoint(dum, w_index); + if (!ep2 || ep2->ep.name == ep0name) { + ret_val = -EOPNOTSUPP; + break; + } + ep2->halted = 1; + ret_val = 0; + *status = 0; + } + break; + case USB_REQ_CLEAR_FEATURE: + if (setup->bRequestType == Dev_Request) { + ret_val = 0; + switch (w_value) { + case USB_DEVICE_REMOTE_WAKEUP: + w_value = USB_DEVICE_REMOTE_WAKEUP; + break; + default: + ret_val = -EOPNOTSUPP; + break; + } + if (ret_val == 0) { + dum->devstatus &= ~(1 << w_value); + *status = 0; + } + } else if (setup->bRequestType == Ep_Request) { + /* endpoint halt */ + ep2 = find_endpoint(dum, w_index); + if (!ep2) { + ret_val = -EOPNOTSUPP; + break; + } + if (!ep2->wedged) + ep2->halted = 0; + ret_val = 0; + *status = 0; + } + break; + case USB_REQ_GET_STATUS: + if (setup->bRequestType == Dev_InRequest + || setup->bRequestType == Intf_InRequest + || setup->bRequestType == Ep_InRequest) { + char *buf; + /* + * device: remote wakeup, selfpowered + * interface: nothing + * endpoint: halt + */ + buf = (char *)urb->transfer_buffer; + if (urb->transfer_buffer_length > 0) { + if (setup->bRequestType == Ep_InRequest) { + ep2 = find_endpoint(dum, w_index); + if (!ep2) { + ret_val = -EOPNOTSUPP; + break; + } + buf[0] = ep2->halted; + } else if (setup->bRequestType == + Dev_InRequest) { + buf[0] = (u8)dum->devstatus; + } else + buf[0] = 0; + } + if (urb->transfer_buffer_length > 1) + buf[1] = 0; + urb->actual_length = min_t(u32, 2, + urb->transfer_buffer_length); + ret_val = 0; + *status = 0; + } + break; + } + return ret_val; +} + /* drive both sides of the transfers; looks like irq handlers to * both drivers except the callbacks aren't in_irq(). */ @@ -1299,14 +1432,8 @@ restart: if (ep == &dum->ep [0] && ep->setup_stage) { struct usb_ctrlrequest setup; int value = 1; - struct dummy_ep *ep2; - unsigned w_index; - unsigned w_value; setup = *(struct usb_ctrlrequest*) urb->setup_packet; - w_index = le16_to_cpu(setup.wIndex); - w_value = le16_to_cpu(setup.wValue); - /* paranoia, in case of stale queued data */ list_for_each_entry (req, &ep->queue, queue) { list_del_init (&req->queue); @@ -1328,117 +1455,9 @@ restart: ep->last_io = jiffies; ep->setup_stage = 0; ep->halted = 0; - switch (setup.bRequest) { - case USB_REQ_SET_ADDRESS: - if (setup.bRequestType != Dev_Request) - break; - dum->address = w_value; - status = 0; - dev_dbg (udc_dev(dum), "set_address = %d\n", - w_value); - value = 0; - break; - case USB_REQ_SET_FEATURE: - if (setup.bRequestType == Dev_Request) { - value = 0; - switch (w_value) { - case USB_DEVICE_REMOTE_WAKEUP: - break; - case USB_DEVICE_B_HNP_ENABLE: - dum->gadget.b_hnp_enable = 1; - break; - case USB_DEVICE_A_HNP_SUPPORT: - dum->gadget.a_hnp_support = 1; - break; - case USB_DEVICE_A_ALT_HNP_SUPPORT: - dum->gadget.a_alt_hnp_support - = 1; - break; - default: - value = -EOPNOTSUPP; - } - if (value == 0) { - dum->devstatus |= - (1 << w_value); - status = 0; - } - } else if (setup.bRequestType == Ep_Request) { - // endpoint halt - ep2 = find_endpoint (dum, w_index); - if (!ep2 || ep2->ep.name == ep0name) { - value = -EOPNOTSUPP; - break; - } - ep2->halted = 1; - value = 0; - status = 0; - } - break; - case USB_REQ_CLEAR_FEATURE: - if (setup.bRequestType == Dev_Request) { - switch (w_value) { - case USB_DEVICE_REMOTE_WAKEUP: - dum->devstatus &= ~(1 << - USB_DEVICE_REMOTE_WAKEUP); - value = 0; - status = 0; - break; - default: - value = -EOPNOTSUPP; - break; - } - } else if (setup.bRequestType == Ep_Request) { - // endpoint halt - ep2 = find_endpoint (dum, w_index); - if (!ep2) { - value = -EOPNOTSUPP; - break; - } - if (!ep2->wedged) - ep2->halted = 0; - value = 0; - status = 0; - } - break; - case USB_REQ_GET_STATUS: - if (setup.bRequestType == Dev_InRequest - || setup.bRequestType - == Intf_InRequest - || setup.bRequestType - == Ep_InRequest - ) { - char *buf; - - // device: remote wakeup, selfpowered - // interface: nothing - // endpoint: halt - buf = (char *)urb->transfer_buffer; - if (urb->transfer_buffer_length > 0) { - if (setup.bRequestType == - Ep_InRequest) { - ep2 = find_endpoint (dum, w_index); - if (!ep2) { - value = -EOPNOTSUPP; - break; - } - buf [0] = ep2->halted; - } else if (setup.bRequestType == - Dev_InRequest) { - buf [0] = (u8) - dum->devstatus; - } else - buf [0] = 0; - } - if (urb->transfer_buffer_length > 1) - buf [1] = 0; - urb->actual_length = min_t(u32, 2, - urb->transfer_buffer_length); - value = 0; - status = 0; - } - break; - } + value = handle_control_request(dum, urb, &setup, + &status); /* gadget driver handles all other requests. block * until setup() returns; no reentrancy issues etc. diff --git a/drivers/usb/gadget/f_fs.c b/drivers/usb/gadget/f_fs.c index 484c5ba5450e..1499f9e4afa8 100644 --- a/drivers/usb/gadget/f_fs.c +++ b/drivers/usb/gadget/f_fs.c @@ -1,10 +1,10 @@ /* - * f_fs.c -- user mode filesystem api for usb composite funtcion controllers + * f_fs.c -- user mode file system API for USB composite function controllers * * Copyright (C) 2010 Samsung Electronics * Author: Michal Nazarewicz <m.nazarewicz@samsung.com> * - * Based on inode.c (GadgetFS): + * Based on inode.c (GadgetFS) which was: * Copyright (C) 2003-2004 David Brownell * Copyright (C) 2003 Agilent Technologies * @@ -38,62 +38,56 @@ #define FUNCTIONFS_MAGIC 0xa647361 /* Chosen by a honest dice roll ;) */ -/* Debuging *****************************************************************/ - -#define ffs_printk(level, fmt, args...) printk(level "f_fs: " fmt "\n", ## args) - -#define FERR(...) ffs_printk(KERN_ERR, __VA_ARGS__) -#define FINFO(...) ffs_printk(KERN_INFO, __VA_ARGS__) - -#ifdef DEBUG -# define FDBG(...) ffs_printk(KERN_DEBUG, __VA_ARGS__) -#else -# define FDBG(...) do { } while (0) -#endif /* DEBUG */ - -#ifdef VERBOSE_DEBUG -# define FVDBG FDBG -#else -# define FVDBG(...) do { } while (0) -#endif /* VERBOSE_DEBUG */ - -#define ENTER() FVDBG("%s()", __func__) +/* Debugging ****************************************************************/ #ifdef VERBOSE_DEBUG +# define pr_vdebug pr_debug # define ffs_dump_mem(prefix, ptr, len) \ - print_hex_dump_bytes("f_fs" prefix ": ", DUMP_PREFIX_NONE, ptr, len) + print_hex_dump_bytes(pr_fmt(prefix ": "), DUMP_PREFIX_NONE, ptr, len) #else +# define pr_vdebug(...) do { } while (0) # define ffs_dump_mem(prefix, ptr, len) do { } while (0) -#endif +#endif /* VERBOSE_DEBUG */ + +#define ENTER() pr_vdebug("%s()\n", __func__) /* The data structure and setup file ****************************************/ enum ffs_state { - /* Waiting for descriptors and strings. */ - /* In this state no open(2), read(2) or write(2) on epfiles + /* + * Waiting for descriptors and strings. + * + * In this state no open(2), read(2) or write(2) on epfiles * may succeed (which should not be the problem as there - * should be no such files opened in the firts place). */ + * should be no such files opened in the first place). + */ FFS_READ_DESCRIPTORS, FFS_READ_STRINGS, - /* We've got descriptors and strings. We are or have called + /* + * We've got descriptors and strings. We are or have called * functionfs_ready_callback(). functionfs_bind() may have - * been called but we don't know. */ - /* This is the only state in which operations on epfiles may - * succeed. */ + * been called but we don't know. + * + * This is the only state in which operations on epfiles may + * succeed. + */ FFS_ACTIVE, - /* All endpoints have been closed. This state is also set if + /* + * All endpoints have been closed. This state is also set if * we encounter an unrecoverable error. The only * unrecoverable error is situation when after reading strings - * from user space we fail to initialise EP files or - * functionfs_ready_callback() returns with error (<0). */ - /* In this state no open(2), read(2) or write(2) (both on ep0 + * from user space we fail to initialise epfiles or + * functionfs_ready_callback() returns with error (<0). + * + * In this state no open(2), read(2) or write(2) (both on ep0 * as well as epfile) may succeed (at this point epfiles are * unlinked and all closed so this is not a problem; ep0 is * also closed but ep0 file exists and so open(2) on ep0 must - * fail). */ + * fail). + */ FFS_CLOSING }; @@ -101,14 +95,18 @@ enum ffs_state { enum ffs_setup_state { /* There is no setup request pending. */ FFS_NO_SETUP, - /* User has read events and there was a setup request event + /* + * User has read events and there was a setup request event * there. The next read/write on ep0 will handle the - * request. */ + * request. + */ FFS_SETUP_PENDING, - /* There was event pending but before user space handled it + /* + * There was event pending but before user space handled it * some other event was introduced which canceled existing * setup. If this state is set read/write on ep0 return - * -EIDRM. This state is only set when adding event. */ + * -EIDRM. This state is only set when adding event. + */ FFS_SETUP_CANCELED }; @@ -120,23 +118,29 @@ struct ffs_function; struct ffs_data { struct usb_gadget *gadget; - /* Protect access read/write operations, only one read/write + /* + * Protect access read/write operations, only one read/write * at a time. As a consequence protects ep0req and company. * While setup request is being processed (queued) this is - * held. */ + * held. + */ struct mutex mutex; - /* Protect access to enpoint related structures (basically + /* + * Protect access to endpoint related structures (basically * usb_ep_queue(), usb_ep_dequeue(), etc. calls) except for - * endpint zero. */ + * endpoint zero. + */ spinlock_t eps_lock; - /* XXX REVISIT do we need our own request? Since we are not - * handling setup requests immidiatelly user space may be so + /* + * XXX REVISIT do we need our own request? Since we are not + * handling setup requests immediately user space may be so * slow that another setup will be sent to the gadget but this * time not to us but another function and then there could be * a race. Is that the case? Or maybe we can use cdev->req - * after all, maybe we just need some spinlock for that? */ + * after all, maybe we just need some spinlock for that? + */ struct usb_request *ep0req; /* P: mutex */ struct completion ep0req_completion; /* P: mutex */ int ep0req_status; /* P: mutex */ @@ -150,7 +154,7 @@ struct ffs_data { enum ffs_state state; /* - * Possible transations: + * Possible transitions: * + FFS_NO_SETUP -> FFS_SETUP_PENDING -- P: ev.waitq.lock * happens only in ep0 read which is P: mutex * + FFS_SETUP_PENDING -> FFS_NO_SETUP -- P: ev.waitq.lock @@ -183,18 +187,21 @@ struct ffs_data { /* Active function */ struct ffs_function *func; - /* Device name, write once when file system is mounted. - * Intendet for user to read if she wants. */ + /* + * Device name, write once when file system is mounted. + * Intended for user to read if she wants. + */ const char *dev_name; - /* Private data for our user (ie. gadget). Managed by - * user. */ + /* Private data for our user (ie. gadget). Managed by user. */ void *private_data; /* filled by __ffs_data_got_descs() */ - /* real descriptors are 16 bytes after raw_descs (so you need + /* + * Real descriptors are 16 bytes after raw_descs (so you need * to skip 16 bytes (ie. ffs->raw_descs + 16) to get to the * first full speed descriptor). raw_descs_length and - * raw_fs_descs_length do not have those 16 bytes added. */ + * raw_fs_descs_length do not have those 16 bytes added. + */ const void *raw_descs; unsigned raw_descs_length; unsigned raw_fs_descs_length; @@ -211,18 +218,23 @@ struct ffs_data { const void *raw_strings; struct usb_gadget_strings **stringtabs; - /* File system's super block, write once when file system is mounted. */ + /* + * File system's super block, write once when file system is + * mounted. + */ struct super_block *sb; - /* File permissions, written once when fs is mounted*/ + /* File permissions, written once when fs is mounted */ struct ffs_file_perms { umode_t mode; uid_t uid; gid_t gid; } file_perms; - /* The endpoint files, filled by ffs_epfiles_create(), - * destroyed by ffs_epfiles_destroy(). */ + /* + * The endpoint files, filled by ffs_epfiles_create(), + * destroyed by ffs_epfiles_destroy(). + */ struct ffs_epfile *epfiles; }; @@ -236,7 +248,7 @@ static struct ffs_data *__must_check ffs_data_new(void) __attribute__((malloc)); static void ffs_data_opened(struct ffs_data *ffs); static void ffs_data_closed(struct ffs_data *ffs); -/* Called with ffs->mutex held; take over ownerrship of data. */ +/* Called with ffs->mutex held; take over ownership of data. */ static int __must_check __ffs_data_got_descs(struct ffs_data *ffs, char *data, size_t len); static int __must_check @@ -267,11 +279,9 @@ static struct ffs_function *ffs_func_from_usb(struct usb_function *f) static void ffs_func_free(struct ffs_function *func); - static void ffs_func_eps_disable(struct ffs_function *func); static int __must_check ffs_func_eps_enable(struct ffs_function *func); - static int ffs_func_bind(struct usb_configuration *, struct usb_function *); static void ffs_func_unbind(struct usb_configuration *, @@ -288,7 +298,6 @@ static int ffs_func_revmap_ep(struct ffs_function *func, u8 num); static int ffs_func_revmap_intf(struct ffs_function *func, u8 intf); - /* The endpoints structures *************************************************/ struct ffs_ep { @@ -321,7 +330,6 @@ struct ffs_epfile { unsigned char _pad; }; - static int __must_check ffs_epfiles_create(struct ffs_data *ffs); static void ffs_epfiles_destroy(struct ffs_epfile *epfiles, unsigned count); @@ -348,7 +356,6 @@ static void ffs_ep0_complete(struct usb_ep *ep, struct usb_request *req) complete_all(&ffs->ep0req_completion); } - static int __ffs_ep0_queue_wait(struct ffs_data *ffs, char *data, size_t len) { struct usb_request *req = ffs->ep0req; @@ -380,17 +387,16 @@ static int __ffs_ep0_queue_wait(struct ffs_data *ffs, char *data, size_t len) static int __ffs_ep0_stall(struct ffs_data *ffs) { if (ffs->ev.can_stall) { - FVDBG("ep0 stall\n"); + pr_vdebug("ep0 stall\n"); usb_ep_set_halt(ffs->gadget->ep0); ffs->setup_state = FFS_NO_SETUP; return -EL2HLT; } else { - FDBG("bogus ep0 stall!\n"); + pr_debug("bogus ep0 stall!\n"); return -ESRCH; } } - static ssize_t ffs_ep0_write(struct file *file, const char __user *buf, size_t len, loff_t *ptr) { @@ -409,7 +415,6 @@ static ssize_t ffs_ep0_write(struct file *file, const char __user *buf, if (unlikely(ret < 0)) return ret; - /* Check state */ switch (ffs->state) { case FFS_READ_DESCRIPTORS: @@ -421,14 +426,14 @@ static ssize_t ffs_ep0_write(struct file *file, const char __user *buf, } data = ffs_prepare_buffer(buf, len); - if (unlikely(IS_ERR(data))) { + if (IS_ERR(data)) { ret = PTR_ERR(data); break; } /* Handle data */ if (ffs->state == FFS_READ_DESCRIPTORS) { - FINFO("read descriptors"); + pr_info("read descriptors\n"); ret = __ffs_data_got_descs(ffs, data, len); if (unlikely(ret < 0)) break; @@ -436,7 +441,7 @@ static ssize_t ffs_ep0_write(struct file *file, const char __user *buf, ffs->state = FFS_READ_STRINGS; ret = len; } else { - FINFO("read strings"); + pr_info("read strings\n"); ret = __ffs_data_got_strings(ffs, data, len); if (unlikely(ret < 0)) break; @@ -461,11 +466,12 @@ static ssize_t ffs_ep0_write(struct file *file, const char __user *buf, } break; - case FFS_ACTIVE: data = NULL; - /* We're called from user space, we can use _irq - * rather then _irqsave */ + /* + * We're called from user space, we can use _irq + * rather then _irqsave + */ spin_lock_irq(&ffs->ev.waitq.lock); switch (FFS_SETUP_STATE(ffs)) { case FFS_SETUP_CANCELED: @@ -493,23 +499,25 @@ static ssize_t ffs_ep0_write(struct file *file, const char __user *buf, spin_unlock_irq(&ffs->ev.waitq.lock); data = ffs_prepare_buffer(buf, len); - if (unlikely(IS_ERR(data))) { + if (IS_ERR(data)) { ret = PTR_ERR(data); break; } spin_lock_irq(&ffs->ev.waitq.lock); - /* We are guaranteed to be still in FFS_ACTIVE state + /* + * We are guaranteed to be still in FFS_ACTIVE state * but the state of setup could have changed from * FFS_SETUP_PENDING to FFS_SETUP_CANCELED so we need * to check for that. If that happened we copied data - * from user space in vain but it's unlikely. */ - /* For sure we are not in FFS_NO_SETUP since this is + * from user space in vain but it's unlikely. + * + * For sure we are not in FFS_NO_SETUP since this is * the only place FFS_SETUP_PENDING -> FFS_NO_SETUP * transition can be performed and it's protected by - * mutex. */ - + * mutex. + */ if (FFS_SETUP_STATE(ffs) == FFS_SETUP_CANCELED) { ret = -EIDRM; done_spin: @@ -521,25 +529,22 @@ done_spin: kfree(data); break; - default: ret = -EBADFD; break; } - mutex_unlock(&ffs->mutex); return ret; } - - static ssize_t __ffs_ep0_read_events(struct ffs_data *ffs, char __user *buf, size_t n) { - /* We are holding ffs->ev.waitq.lock and ffs->mutex and we need - * to release them. */ - + /* + * We are holding ffs->ev.waitq.lock and ffs->mutex and we need + * to release them. + */ struct usb_functionfs_event events[n]; unsigned i = 0; @@ -568,7 +573,6 @@ static ssize_t __ffs_ep0_read_events(struct ffs_data *ffs, char __user *buf, ? -EFAULT : sizeof events; } - static ssize_t ffs_ep0_read(struct file *file, char __user *buf, size_t len, loff_t *ptr) { @@ -588,16 +592,16 @@ static ssize_t ffs_ep0_read(struct file *file, char __user *buf, if (unlikely(ret < 0)) return ret; - /* Check state */ if (ffs->state != FFS_ACTIVE) { ret = -EBADFD; goto done_mutex; } - - /* We're called from user space, we can use _irq rather then - * _irqsave */ + /* + * We're called from user space, we can use _irq rather then + * _irqsave + */ spin_lock_irq(&ffs->ev.waitq.lock); switch (FFS_SETUP_STATE(ffs)) { @@ -617,7 +621,8 @@ static ssize_t ffs_ep0_read(struct file *file, char __user *buf, break; } - if (unlikely(wait_event_interruptible_exclusive_locked_irq(ffs->ev.waitq, ffs->ev.count))) { + if (wait_event_interruptible_exclusive_locked_irq(ffs->ev.waitq, + ffs->ev.count)) { ret = -EINTR; break; } @@ -625,7 +630,6 @@ static ssize_t ffs_ep0_read(struct file *file, char __user *buf, return __ffs_ep0_read_events(ffs, buf, min(n, (size_t)ffs->ev.count)); - case FFS_SETUP_PENDING: if (ffs->ev.setup.bRequestType & USB_DIR_IN) { spin_unlock_irq(&ffs->ev.waitq.lock); @@ -671,8 +675,6 @@ done_mutex: return ret; } - - static int ffs_ep0_open(struct inode *inode, struct file *file) { struct ffs_data *ffs = inode->i_private; @@ -688,7 +690,6 @@ static int ffs_ep0_open(struct inode *inode, struct file *file) return 0; } - static int ffs_ep0_release(struct inode *inode, struct file *file) { struct ffs_data *ffs = file->private_data; @@ -700,7 +701,6 @@ static int ffs_ep0_release(struct inode *inode, struct file *file) return 0; } - static long ffs_ep0_ioctl(struct file *file, unsigned code, unsigned long value) { struct ffs_data *ffs = file->private_data; @@ -721,7 +721,6 @@ static long ffs_ep0_ioctl(struct file *file, unsigned code, unsigned long value) return ret; } - static const struct file_operations ffs_ep0_operations = { .owner = THIS_MODULE, .llseek = no_llseek, @@ -736,7 +735,6 @@ static const struct file_operations ffs_ep0_operations = { /* "Normal" endpoints operations ********************************************/ - static void ffs_epfile_io_complete(struct usb_ep *_ep, struct usb_request *req) { ENTER(); @@ -747,7 +745,6 @@ static void ffs_epfile_io_complete(struct usb_ep *_ep, struct usb_request *req) } } - static ssize_t ffs_epfile_io(struct file *file, char __user *buf, size_t len, int read) { @@ -777,8 +774,8 @@ first_try: goto error; } - if (unlikely(wait_event_interruptible - (epfile->wait, (ep = epfile->ep)))) { + if (wait_event_interruptible(epfile->wait, + (ep = epfile->ep))) { ret = -EINTR; goto error; } @@ -810,12 +807,16 @@ first_try: if (unlikely(ret)) goto error; - /* We're called from user space, we can use _irq rather then - * _irqsave */ + /* + * We're called from user space, we can use _irq rather then + * _irqsave + */ spin_lock_irq(&epfile->ffs->eps_lock); - /* While we were acquiring mutex endpoint got disabled - * or changed? */ + /* + * While we were acquiring mutex endpoint got disabled + * or changed? + */ } while (unlikely(epfile->ep != ep)); /* Halt */ @@ -857,7 +858,6 @@ error: return ret; } - static ssize_t ffs_epfile_write(struct file *file, const char __user *buf, size_t len, loff_t *ptr) @@ -903,7 +903,6 @@ ffs_epfile_release(struct inode *inode, struct file *file) return 0; } - static long ffs_epfile_ioctl(struct file *file, unsigned code, unsigned long value) { @@ -942,7 +941,6 @@ static long ffs_epfile_ioctl(struct file *file, unsigned code, return ret; } - static const struct file_operations ffs_epfile_operations = { .owner = THIS_MODULE, .llseek = no_llseek, @@ -955,15 +953,13 @@ static const struct file_operations ffs_epfile_operations = { }; - /* File system and super block operations ***********************************/ /* - * Mounting the filesystem creates a controller file, used first for + * Mounting the file system creates a controller file, used first for * function configuration then later for event monitoring. */ - static struct inode *__must_check ffs_sb_make_inode(struct super_block *sb, void *data, const struct file_operations *fops, @@ -996,9 +992,7 @@ ffs_sb_make_inode(struct super_block *sb, void *data, return inode; } - /* Create "regular" file */ - static struct inode *ffs_sb_create_file(struct super_block *sb, const char *name, void *data, const struct file_operations *fops, @@ -1027,9 +1021,7 @@ static struct inode *ffs_sb_create_file(struct super_block *sb, return inode; } - /* Super block */ - static const struct super_operations ffs_sb_operations = { .statfs = simple_statfs, .drop_inode = generic_delete_inode, @@ -1050,7 +1042,7 @@ static int ffs_sb_fill(struct super_block *sb, void *_data, int silent) ENTER(); - /* Initialize data */ + /* Initialise data */ ffs = ffs_data_new(); if (unlikely(!ffs)) goto enomem0; @@ -1096,7 +1088,6 @@ enomem0: return -ENOMEM; } - static int ffs_fs_parse_opts(struct ffs_sb_fill_data *data, char *opts) { ENTER(); @@ -1116,7 +1107,7 @@ static int ffs_fs_parse_opts(struct ffs_sb_fill_data *data, char *opts) /* Value limit */ eq = strchr(opts, '='); if (unlikely(!eq)) { - FERR("'=' missing in %s", opts); + pr_err("'=' missing in %s\n", opts); return -EINVAL; } *eq = 0; @@ -1124,7 +1115,7 @@ static int ffs_fs_parse_opts(struct ffs_sb_fill_data *data, char *opts) /* Parse value */ value = simple_strtoul(eq + 1, &end, 0); if (unlikely(*end != ',' && *end != 0)) { - FERR("%s: invalid value: %s", opts, eq + 1); + pr_err("%s: invalid value: %s\n", opts, eq + 1); return -EINVAL; } @@ -1159,7 +1150,7 @@ static int ffs_fs_parse_opts(struct ffs_sb_fill_data *data, char *opts) default: invalid: - FERR("%s: invalid option", opts); + pr_err("%s: invalid option\n", opts); return -EINVAL; } @@ -1172,7 +1163,6 @@ invalid: return 0; } - /* "mount -t functionfs dev_name /dev/function" ends up here */ static struct dentry * @@ -1224,10 +1214,8 @@ static struct file_system_type ffs_fs_type = { }; - /* Driver's main init/cleanup functions *************************************/ - static int functionfs_init(void) { int ret; @@ -1236,9 +1224,9 @@ static int functionfs_init(void) ret = register_filesystem(&ffs_fs_type); if (likely(!ret)) - FINFO("file system registered"); + pr_info("file system registered\n"); else - FERR("failed registering file system (%d)", ret); + pr_err("failed registering file system (%d)\n", ret); return ret; } @@ -1247,18 +1235,16 @@ static void functionfs_cleanup(void) { ENTER(); - FINFO("unloading"); + pr_info("unloading\n"); unregister_filesystem(&ffs_fs_type); } - /* ffs_data and ffs_function construction and destruction code **************/ static void ffs_data_clear(struct ffs_data *ffs); static void ffs_data_reset(struct ffs_data *ffs); - static void ffs_data_get(struct ffs_data *ffs) { ENTER(); @@ -1279,7 +1265,7 @@ static void ffs_data_put(struct ffs_data *ffs) ENTER(); if (unlikely(atomic_dec_and_test(&ffs->ref))) { - FINFO("%s(): freeing", __func__); + pr_info("%s(): freeing\n", __func__); ffs_data_clear(ffs); BUG_ON(mutex_is_locked(&ffs->mutex) || spin_is_locked(&ffs->ev.waitq.lock) || @@ -1289,8 +1275,6 @@ static void ffs_data_put(struct ffs_data *ffs) } } - - static void ffs_data_closed(struct ffs_data *ffs) { ENTER(); @@ -1303,7 +1287,6 @@ static void ffs_data_closed(struct ffs_data *ffs) ffs_data_put(ffs); } - static struct ffs_data *ffs_data_new(void) { struct ffs_data *ffs = kzalloc(sizeof *ffs, GFP_KERNEL); @@ -1326,7 +1309,6 @@ static struct ffs_data *ffs_data_new(void) return ffs; } - static void ffs_data_clear(struct ffs_data *ffs) { ENTER(); @@ -1344,7 +1326,6 @@ static void ffs_data_clear(struct ffs_data *ffs) kfree(ffs->stringtabs); } - static void ffs_data_reset(struct ffs_data *ffs) { ENTER(); @@ -1407,7 +1388,6 @@ static int functionfs_bind(struct ffs_data *ffs, struct usb_composite_dev *cdev) return 0; } - static void functionfs_unbind(struct ffs_data *ffs) { ENTER(); @@ -1420,7 +1400,6 @@ static void functionfs_unbind(struct ffs_data *ffs) } } - static int ffs_epfiles_create(struct ffs_data *ffs) { struct ffs_epfile *epfile, *epfiles; @@ -1451,7 +1430,6 @@ static int ffs_epfiles_create(struct ffs_data *ffs) return 0; } - static void ffs_epfiles_destroy(struct ffs_epfile *epfiles, unsigned count) { struct ffs_epfile *epfile = epfiles; @@ -1471,7 +1449,6 @@ static void ffs_epfiles_destroy(struct ffs_epfile *epfiles, unsigned count) kfree(epfiles); } - static int functionfs_bind_config(struct usb_composite_dev *cdev, struct usb_configuration *c, struct ffs_data *ffs) @@ -1491,7 +1468,6 @@ static int functionfs_bind_config(struct usb_composite_dev *cdev, func->function.bind = ffs_func_bind; func->function.unbind = ffs_func_unbind; func->function.set_alt = ffs_func_set_alt; - /*func->function.get_alt = ffs_func_get_alt;*/ func->function.disable = ffs_func_disable; func->function.setup = ffs_func_setup; func->function.suspend = ffs_func_suspend; @@ -1516,14 +1492,15 @@ static void ffs_func_free(struct ffs_function *func) ffs_data_put(func->ffs); kfree(func->eps); - /* eps and interfaces_nums are allocated in the same chunk so + /* + * eps and interfaces_nums are allocated in the same chunk so * only one free is required. Descriptors are also allocated - * in the same chunk. */ + * in the same chunk. + */ kfree(func); } - static void ffs_func_eps_disable(struct ffs_function *func) { struct ffs_ep *ep = func->eps; @@ -1581,11 +1558,12 @@ static int ffs_func_eps_enable(struct ffs_function *func) /* Parsing and building descriptors and strings *****************************/ - -/* This validates if data pointed by data is a valid USB descriptor as +/* + * This validates if data pointed by data is a valid USB descriptor as * well as record how many interfaces, endpoints and strings are - * required by given configuration. Returns address afther the - * descriptor or NULL if data is invalid. */ + * required by given configuration. Returns address after the + * descriptor or NULL if data is invalid. + */ enum ffs_entity_type { FFS_DESCRIPTOR, FFS_INTERFACE, FFS_STRING, FFS_ENDPOINT @@ -1607,14 +1585,14 @@ static int __must_check ffs_do_desc(char *data, unsigned len, /* At least two bytes are required: length and type */ if (len < 2) { - FVDBG("descriptor too short"); + pr_vdebug("descriptor too short\n"); return -EINVAL; } /* If we have at least as many bytes as the descriptor takes? */ length = _ds->bLength; if (len < length) { - FVDBG("descriptor longer then available data"); + pr_vdebug("descriptor longer then available data\n"); return -EINVAL; } @@ -1622,15 +1600,15 @@ static int __must_check ffs_do_desc(char *data, unsigned len, #define __entity_check_STRING(val) (val) #define __entity_check_ENDPOINT(val) ((val) & USB_ENDPOINT_NUMBER_MASK) #define __entity(type, val) do { \ - FVDBG("entity " #type "(%02x)", (val)); \ + pr_vdebug("entity " #type "(%02x)\n", (val)); \ if (unlikely(!__entity_check_ ##type(val))) { \ - FVDBG("invalid entity's value"); \ + pr_vdebug("invalid entity's value\n"); \ return -EINVAL; \ } \ ret = entity(FFS_ ##type, &val, _ds, priv); \ if (unlikely(ret < 0)) { \ - FDBG("entity " #type "(%02x); ret = %d", \ - (val), ret); \ + pr_debug("entity " #type "(%02x); ret = %d\n", \ + (val), ret); \ return ret; \ } \ } while (0) @@ -1642,12 +1620,13 @@ static int __must_check ffs_do_desc(char *data, unsigned len, case USB_DT_STRING: case USB_DT_DEVICE_QUALIFIER: /* function can't have any of those */ - FVDBG("descriptor reserved for gadget: %d", _ds->bDescriptorType); + pr_vdebug("descriptor reserved for gadget: %d\n", + _ds->bDescriptorType); return -EINVAL; case USB_DT_INTERFACE: { struct usb_interface_descriptor *ds = (void *)_ds; - FVDBG("interface descriptor"); + pr_vdebug("interface descriptor\n"); if (length != sizeof *ds) goto inv_length; @@ -1659,7 +1638,7 @@ static int __must_check ffs_do_desc(char *data, unsigned len, case USB_DT_ENDPOINT: { struct usb_endpoint_descriptor *ds = (void *)_ds; - FVDBG("endpoint descriptor"); + pr_vdebug("endpoint descriptor\n"); if (length != USB_DT_ENDPOINT_SIZE && length != USB_DT_ENDPOINT_AUDIO_SIZE) goto inv_length; @@ -1674,7 +1653,7 @@ static int __must_check ffs_do_desc(char *data, unsigned len, case USB_DT_INTERFACE_ASSOCIATION: { struct usb_interface_assoc_descriptor *ds = (void *)_ds; - FVDBG("interface association descriptor"); + pr_vdebug("interface association descriptor\n"); if (length != sizeof *ds) goto inv_length; if (ds->iFunction) @@ -1688,17 +1667,17 @@ static int __must_check ffs_do_desc(char *data, unsigned len, case USB_DT_SECURITY: case USB_DT_CS_RADIO_CONTROL: /* TODO */ - FVDBG("unimplemented descriptor: %d", _ds->bDescriptorType); + pr_vdebug("unimplemented descriptor: %d\n", _ds->bDescriptorType); return -EINVAL; default: /* We should never be here */ - FVDBG("unknown descriptor: %d", _ds->bDescriptorType); + pr_vdebug("unknown descriptor: %d\n", _ds->bDescriptorType); return -EINVAL; - inv_length: - FVDBG("invalid length: %d (descriptor %d)", - _ds->bLength, _ds->bDescriptorType); +inv_length: + pr_vdebug("invalid length: %d (descriptor %d)\n", + _ds->bLength, _ds->bDescriptorType); return -EINVAL; } @@ -1711,7 +1690,6 @@ static int __must_check ffs_do_desc(char *data, unsigned len, return length; } - static int __must_check ffs_do_descs(unsigned count, char *data, unsigned len, ffs_entity_callback entity, void *priv) { @@ -1726,10 +1704,11 @@ static int __must_check ffs_do_descs(unsigned count, char *data, unsigned len, if (num == count) data = NULL; - /* Record "descriptor" entitny */ + /* Record "descriptor" entity */ ret = entity(FFS_DESCRIPTOR, (u8 *)num, (void *)data, priv); if (unlikely(ret < 0)) { - FDBG("entity DESCRIPTOR(%02lx); ret = %d", num, ret); + pr_debug("entity DESCRIPTOR(%02lx); ret = %d\n", + num, ret); return ret; } @@ -1738,7 +1717,7 @@ static int __must_check ffs_do_descs(unsigned count, char *data, unsigned len, ret = ffs_do_desc(data, len, entity, priv); if (unlikely(ret < 0)) { - FDBG("%s returns %d", __func__, ret); + pr_debug("%s returns %d\n", __func__, ret); return ret; } @@ -1748,7 +1727,6 @@ static int __must_check ffs_do_descs(unsigned count, char *data, unsigned len, } } - static int __ffs_data_do_entity(enum ffs_entity_type type, u8 *valuep, struct usb_descriptor_header *desc, void *priv) @@ -1762,16 +1740,20 @@ static int __ffs_data_do_entity(enum ffs_entity_type type, break; case FFS_INTERFACE: - /* Interfaces are indexed from zero so if we + /* + * Interfaces are indexed from zero so if we * encountered interface "n" then there are at least - * "n+1" interfaces. */ + * "n+1" interfaces. + */ if (*valuep >= ffs->interfaces_count) ffs->interfaces_count = *valuep + 1; break; case FFS_STRING: - /* Strings are indexed from 1 (0 is magic ;) reserved - * for languages list or some such) */ + /* + * Strings are indexed from 1 (0 is magic ;) reserved + * for languages list or some such) + */ if (*valuep > ffs->strings_count) ffs->strings_count = *valuep; break; @@ -1786,7 +1768,6 @@ static int __ffs_data_do_entity(enum ffs_entity_type type, return 0; } - static int __ffs_data_got_descs(struct ffs_data *ffs, char *const _data, size_t len) { @@ -1849,8 +1830,6 @@ error: return ret; } - - static int __ffs_data_got_strings(struct ffs_data *ffs, char *const _data, size_t len) { @@ -1876,17 +1855,17 @@ static int __ffs_data_got_strings(struct ffs_data *ffs, if (unlikely(str_count < needed_count)) goto error; - /* If we don't need any strings just return and free all - * memory */ + /* + * If we don't need any strings just return and free all + * memory. + */ if (!needed_count) { kfree(_data); return 0; } - /* Allocate */ + /* Allocate everything in one chunk so there's less maintenance. */ { - /* Allocate everything in one chunk so there's less - * maintanance. */ struct { struct usb_gadget_strings *stringtabs[lang_count + 1]; struct usb_gadget_strings stringtab[lang_count]; @@ -1937,13 +1916,17 @@ static int __ffs_data_got_strings(struct ffs_data *ffs, if (unlikely(length == len)) goto error_free; - /* user may provide more strings then we need, - * if that's the case we simply ingore the - * rest */ + /* + * User may provide more strings then we need, + * if that's the case we simply ignore the + * rest + */ if (likely(needed)) { - /* s->id will be set while adding + /* + * s->id will be set while adding * function to configuration so for - * now just leave garbage here. */ + * now just leave garbage here. + */ s->s = data; --needed; ++s; @@ -1977,8 +1960,6 @@ error: } - - /* Events handling and management *******************************************/ static void __ffs_event_add(struct ffs_data *ffs, @@ -1987,29 +1968,32 @@ static void __ffs_event_add(struct ffs_data *ffs, enum usb_functionfs_event_type rem_type1, rem_type2 = type; int neg = 0; - /* Abort any unhandled setup */ - /* We do not need to worry about some cmpxchg() changing value + /* + * Abort any unhandled setup + * + * We do not need to worry about some cmpxchg() changing value * of ffs->setup_state without holding the lock because when * state is FFS_SETUP_PENDING cmpxchg() in several places in - * the source does nothing. */ + * the source does nothing. + */ if (ffs->setup_state == FFS_SETUP_PENDING) ffs->setup_state = FFS_SETUP_CANCELED; switch (type) { case FUNCTIONFS_RESUME: rem_type2 = FUNCTIONFS_SUSPEND; - /* FALL THGOUTH */ + /* FALL THROUGH */ case FUNCTIONFS_SUSPEND: case FUNCTIONFS_SETUP: rem_type1 = type; - /* discard all similar events */ + /* Discard all similar events */ break; case FUNCTIONFS_BIND: case FUNCTIONFS_UNBIND: case FUNCTIONFS_DISABLE: case FUNCTIONFS_ENABLE: - /* discard everything other then power management. */ + /* Discard everything other then power management. */ rem_type1 = FUNCTIONFS_SUSPEND; rem_type2 = FUNCTIONFS_RESUME; neg = 1; @@ -2026,11 +2010,11 @@ static void __ffs_event_add(struct ffs_data *ffs, if ((*ev == rem_type1 || *ev == rem_type2) == neg) *out++ = *ev; else - FVDBG("purging event %d", *ev); + pr_vdebug("purging event %d\n", *ev); ffs->ev.count = out - ffs->ev.types; } - FVDBG("adding event %d", type); + pr_vdebug("adding event %d\n", type); ffs->ev.types[ffs->ev.count++] = type; wake_up_locked(&ffs->ev.waitq); } @@ -2055,8 +2039,10 @@ static int __ffs_func_bind_do_descs(enum ffs_entity_type type, u8 *valuep, struct ffs_function *func = priv; struct ffs_ep *ffs_ep; - /* If hs_descriptors is not NULL then we are reading hs - * descriptors now */ + /* + * If hs_descriptors is not NULL then we are reading hs + * descriptors now + */ const int isHS = func->function.hs_descriptors != NULL; unsigned idx; @@ -2075,9 +2061,9 @@ static int __ffs_func_bind_do_descs(enum ffs_entity_type type, u8 *valuep, ffs_ep = func->eps + idx; if (unlikely(ffs_ep->descs[isHS])) { - FVDBG("two %sspeed descriptors for EP %d", - isHS ? "high" : "full", - ds->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK); + pr_vdebug("two %sspeed descriptors for EP %d\n", + isHS ? "high" : "full", + ds->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK); return -EINVAL; } ffs_ep->descs[isHS] = ds; @@ -2091,11 +2077,11 @@ static int __ffs_func_bind_do_descs(enum ffs_entity_type type, u8 *valuep, struct usb_request *req; struct usb_ep *ep; - FVDBG("autoconfig"); + pr_vdebug("autoconfig\n"); ep = usb_ep_autoconfig(func->gadget, ds); if (unlikely(!ep)) return -ENOTSUPP; - ep->driver_data = func->eps + idx;; + ep->driver_data = func->eps + idx; req = usb_ep_alloc_request(ep, GFP_KERNEL); if (unlikely(!req)) @@ -2111,7 +2097,6 @@ static int __ffs_func_bind_do_descs(enum ffs_entity_type type, u8 *valuep, return 0; } - static int __ffs_func_bind_do_nums(enum ffs_entity_type type, u8 *valuep, struct usb_descriptor_header *desc, void *priv) @@ -2143,8 +2128,10 @@ static int __ffs_func_bind_do_nums(enum ffs_entity_type type, u8 *valuep, break; case FFS_ENDPOINT: - /* USB_DT_ENDPOINT are handled in - * __ffs_func_bind_do_descs(). */ + /* + * USB_DT_ENDPOINT are handled in + * __ffs_func_bind_do_descs(). + */ if (desc->bDescriptorType == USB_DT_ENDPOINT) return 0; @@ -2160,7 +2147,7 @@ static int __ffs_func_bind_do_nums(enum ffs_entity_type type, u8 *valuep, break; } - FVDBG("%02x -> %02x", *valuep, newValue); + pr_vdebug("%02x -> %02x\n", *valuep, newValue); *valuep = newValue; return 0; } @@ -2211,9 +2198,11 @@ static int ffs_func_bind(struct usb_configuration *c, func->eps = data->eps; func->interfaces_nums = data->inums; - /* Go throught all the endpoint descriptors and allocate + /* + * Go through all the endpoint descriptors and allocate * endpoints first, so that later we can rewrite the endpoint - * numbers without worying that it may be described later on. */ + * numbers without worrying that it may be described later on. + */ if (likely(full)) { func->function.descriptors = data->fs_descs; ret = ffs_do_descs(ffs->fs_descs_count, @@ -2234,9 +2223,11 @@ static int ffs_func_bind(struct usb_configuration *c, __ffs_func_bind_do_descs, func); } - /* Now handle interface numbers allocation and interface and - * enpoint numbers rewritting. We can do that in one go - * now. */ + /* + * Now handle interface numbers allocation and interface and + * endpoint numbers rewriting. We can do that in one go + * now. + */ ret = ffs_do_descs(ffs->fs_descs_count + (high ? ffs->hs_descs_count : 0), data->raw_descs, sizeof data->raw_descs, @@ -2274,7 +2265,6 @@ static void ffs_func_unbind(struct usb_configuration *c, ffs_func_free(func); } - static int ffs_func_set_alt(struct usb_function *f, unsigned interface, unsigned alt) { @@ -2322,20 +2312,21 @@ static int ffs_func_setup(struct usb_function *f, ENTER(); - FVDBG("creq->bRequestType = %02x", creq->bRequestType); - FVDBG("creq->bRequest = %02x", creq->bRequest); - FVDBG("creq->wValue = %04x", le16_to_cpu(creq->wValue)); - FVDBG("creq->wIndex = %04x", le16_to_cpu(creq->wIndex)); - FVDBG("creq->wLength = %04x", le16_to_cpu(creq->wLength)); + pr_vdebug("creq->bRequestType = %02x\n", creq->bRequestType); + pr_vdebug("creq->bRequest = %02x\n", creq->bRequest); + pr_vdebug("creq->wValue = %04x\n", le16_to_cpu(creq->wValue)); + pr_vdebug("creq->wIndex = %04x\n", le16_to_cpu(creq->wIndex)); + pr_vdebug("creq->wLength = %04x\n", le16_to_cpu(creq->wLength)); - /* Most requests directed to interface go throught here + /* + * Most requests directed to interface go through here * (notable exceptions are set/get interface) so we need to * handle them. All other either handled by composite or * passed to usb_configuration->setup() (if one is set). No * matter, we will handle requests directed to endpoint here * as well (as it's straightforward) but what to do with any - * other request? */ - + * other request? + */ if (ffs->state != FFS_ACTIVE) return -ENODEV; @@ -2378,8 +2369,7 @@ static void ffs_func_resume(struct usb_function *f) } - -/* Enpoint and interface numbers reverse mapping ****************************/ +/* Endpoint and interface numbers reverse mapping ***************************/ static int ffs_func_revmap_ep(struct ffs_function *func, u8 num) { @@ -2410,7 +2400,6 @@ static int ffs_mutex_lock(struct mutex *mutex, unsigned nonblock) : mutex_lock_interruptible(mutex); } - static char *ffs_prepare_buffer(const char * __user buf, size_t len) { char *data; @@ -2427,7 +2416,7 @@ static char *ffs_prepare_buffer(const char * __user buf, size_t len) return ERR_PTR(-EFAULT); } - FVDBG("Buffer from user space:"); + pr_vdebug("Buffer from user space:\n"); ffs_dump_mem("", data, len); return data; diff --git a/drivers/usb/gadget/f_mass_storage.c b/drivers/usb/gadget/f_mass_storage.c index 838286b1cd14..b5dbb2308f56 100644 --- a/drivers/usb/gadget/f_mass_storage.c +++ b/drivers/usb/gadget/f_mass_storage.c @@ -37,7 +37,6 @@ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ - /* * The Mass Storage Function acts as a USB Mass Storage device, * appearing to the host as a disk drive or as a CD-ROM drive. In @@ -185,7 +184,6 @@ * <http://www.usb.org/developers/devclass_docs/usbmass-ufi10.pdf>. */ - /* * Driver Design * @@ -275,7 +273,6 @@ /* #define VERBOSE_DEBUG */ /* #define DUMP_MSGS */ - #include <linux/blkdev.h> #include <linux/completion.h> #include <linux/dcache.h> @@ -300,7 +297,6 @@ #include "gadget_chips.h" - /*------------------------------------------------------------------------*/ #define FSG_DRIVER_DESC "Mass Storage Function" @@ -308,7 +304,6 @@ static const char fsg_string_interface[] = "Mass Storage"; - #define FSG_NO_INTR_EP 1 #define FSG_NO_DEVICE_STRINGS 1 #define FSG_NO_OTG 1 @@ -324,25 +319,30 @@ struct fsg_common; /* FSF callback functions */ struct fsg_operations { - /* Callback function to call when thread exits. If no + /* + * Callback function to call when thread exits. If no * callback is set or it returns value lower then zero MSF * will force eject all LUNs it operates on (including those * marked as non-removable or with prevent_medium_removal flag - * set). */ + * set). + */ int (*thread_exits)(struct fsg_common *common); - /* Called prior to ejection. Negative return means error, + /* + * Called prior to ejection. Negative return means error, * zero means to continue with ejection, positive means not to - * eject. */ + * eject. + */ int (*pre_eject)(struct fsg_common *common, struct fsg_lun *lun, int num); - /* Called after ejection. Negative return means error, zero - * or positive is just a success. */ + /* + * Called after ejection. Negative return means error, zero + * or positive is just a success. + */ int (*post_eject)(struct fsg_common *common, struct fsg_lun *lun, int num); }; - /* Data shared by all the FSG instances. */ struct fsg_common { struct usb_gadget *gadget; @@ -398,14 +398,15 @@ struct fsg_common { /* Gadget's private data. */ void *private_data; - /* Vendor (8 chars), product (16 chars), release (4 - * hexadecimal digits) and NUL byte */ + /* + * Vendor (8 chars), product (16 chars), release (4 + * hexadecimal digits) and NUL byte + */ char inquiry_string[8 + 16 + 4 + 1]; struct kref ref; }; - struct fsg_config { unsigned nluns; struct fsg_lun_config { @@ -431,7 +432,6 @@ struct fsg_config { char can_stall; }; - struct fsg_dev { struct usb_function function; struct usb_gadget *gadget; /* Copy of cdev->gadget */ @@ -449,7 +449,6 @@ struct fsg_dev { struct usb_ep *bulk_out; }; - static inline int __fsg_is_set(struct fsg_common *common, const char *func, unsigned line) { @@ -462,13 +461,11 @@ static inline int __fsg_is_set(struct fsg_common *common, #define fsg_is_set(common) likely(__fsg_is_set(common, __func__, __LINE__)) - static inline struct fsg_dev *fsg_from_func(struct usb_function *f) { return container_of(f, struct fsg_dev, function); } - typedef void (*fsg_routine_t)(struct fsg_dev *); static int exception_in_progress(struct fsg_common *common) @@ -478,7 +475,7 @@ static int exception_in_progress(struct fsg_common *common) /* Make bulk-out requests be divisible by the maxpacket size */ static void set_bulk_out_req_length(struct fsg_common *common, - struct fsg_buffhd *bh, unsigned int length) + struct fsg_buffhd *bh, unsigned int length) { unsigned int rem; @@ -489,6 +486,7 @@ static void set_bulk_out_req_length(struct fsg_common *common, bh->outreq->length = length; } + /*-------------------------------------------------------------------------*/ static int fsg_set_halt(struct fsg_dev *fsg, struct usb_ep *ep) @@ -519,14 +517,15 @@ static void wakeup_thread(struct fsg_common *common) wake_up_process(common->thread_task); } - static void raise_exception(struct fsg_common *common, enum fsg_state new_state) { unsigned long flags; - /* Do nothing if a higher-priority exception is already in progress. + /* + * Do nothing if a higher-priority exception is already in progress. * If a lower-or-equal priority exception is in progress, preempt it - * and notify the main thread by sending it a signal. */ + * and notify the main thread by sending it a signal. + */ spin_lock_irqsave(&common->lock, flags); if (common->state <= new_state) { common->exception_req_tag = common->ep0_req_tag; @@ -555,10 +554,10 @@ static int ep0_queue(struct fsg_common *common) return rc; } + /*-------------------------------------------------------------------------*/ -/* Bulk and interrupt endpoint completion handlers. - * These always run in_irq. */ +/* Completion handlers. These always run in_irq. */ static void bulk_in_complete(struct usb_ep *ep, struct usb_request *req) { @@ -567,7 +566,7 @@ static void bulk_in_complete(struct usb_ep *ep, struct usb_request *req) if (req->status || req->actual != req->length) DBG(common, "%s --> %d, %u/%u\n", __func__, - req->status, req->actual, req->length); + req->status, req->actual, req->length); if (req->status == -ECONNRESET) /* Request was cancelled */ usb_ep_fifo_flush(ep); @@ -588,8 +587,7 @@ static void bulk_out_complete(struct usb_ep *ep, struct usb_request *req) dump_msg(common, "bulk-out", req->buf, req->actual); if (req->status || req->actual != bh->bulk_out_intended_length) DBG(common, "%s --> %d, %u/%u\n", __func__, - req->status, req->actual, - bh->bulk_out_intended_length); + req->status, req->actual, bh->bulk_out_intended_length); if (req->status == -ECONNRESET) /* Request was cancelled */ usb_ep_fifo_flush(ep); @@ -602,13 +600,8 @@ static void bulk_out_complete(struct usb_ep *ep, struct usb_request *req) spin_unlock(&common->lock); } - -/*-------------------------------------------------------------------------*/ - -/* Ep0 class-specific handlers. These always run in_irq. */ - static int fsg_setup(struct usb_function *f, - const struct usb_ctrlrequest *ctrl) + const struct usb_ctrlrequest *ctrl) { struct fsg_dev *fsg = fsg_from_func(f); struct usb_request *req = fsg->common->ep0req; @@ -628,8 +621,10 @@ static int fsg_setup(struct usb_function *f, if (w_index != fsg->interface_number || w_value != 0) return -EDOM; - /* Raise an exception to stop the current operation - * and reinitialize our state. */ + /* + * Raise an exception to stop the current operation + * and reinitialize our state. + */ DBG(fsg, "bulk reset request\n"); raise_exception(fsg->common, FSG_STATE_RESET); return DELAYED_STATUS; @@ -641,7 +636,7 @@ static int fsg_setup(struct usb_function *f, if (w_index != fsg->interface_number || w_value != 0) return -EDOM; VDBG(fsg, "get max LUN\n"); - *(u8 *) req->buf = fsg->common->nluns - 1; + *(u8 *)req->buf = fsg->common->nluns - 1; /* Respond with data/status */ req->length = min((u16)1, w_length); @@ -649,8 +644,7 @@ static int fsg_setup(struct usb_function *f, } VDBG(fsg, - "unknown class-specific control req " - "%02x.%02x v%04x i%04x l%u\n", + "unknown class-specific control req %02x.%02x v%04x i%04x l%u\n", ctrl->bRequestType, ctrl->bRequest, le16_to_cpu(ctrl->wValue), w_index, w_length); return -EOPNOTSUPP; @@ -661,11 +655,10 @@ static int fsg_setup(struct usb_function *f, /* All the following routines run in process context */ - /* Use this for bulk or interrupt transfers, not ep0 */ static void start_transfer(struct fsg_dev *fsg, struct usb_ep *ep, - struct usb_request *req, int *pbusy, - enum fsg_buffer_state *state) + struct usb_request *req, int *pbusy, + enum fsg_buffer_state *state) { int rc; @@ -683,25 +676,34 @@ static void start_transfer(struct fsg_dev *fsg, struct usb_ep *ep, /* We can't do much more than wait for a reset */ - /* Note: currently the net2280 driver fails zero-length - * submissions if DMA is enabled. */ - if (rc != -ESHUTDOWN && !(rc == -EOPNOTSUPP && - req->length == 0)) + /* + * Note: currently the net2280 driver fails zero-length + * submissions if DMA is enabled. + */ + if (rc != -ESHUTDOWN && + !(rc == -EOPNOTSUPP && req->length == 0)) WARNING(fsg, "error in submission: %s --> %d\n", - ep->name, rc); + ep->name, rc); } } -#define START_TRANSFER_OR(common, ep_name, req, pbusy, state) \ - if (fsg_is_set(common)) \ - start_transfer((common)->fsg, (common)->fsg->ep_name, \ - req, pbusy, state); \ - else - -#define START_TRANSFER(common, ep_name, req, pbusy, state) \ - START_TRANSFER_OR(common, ep_name, req, pbusy, state) (void)0 - +static bool start_in_transfer(struct fsg_common *common, struct fsg_buffhd *bh) +{ + if (!fsg_is_set(common)) + return false; + start_transfer(common->fsg, common->fsg->bulk_in, + bh->inreq, &bh->inreq_busy, &bh->state); + return true; +} +static bool start_out_transfer(struct fsg_common *common, struct fsg_buffhd *bh) +{ + if (!fsg_is_set(common)) + return false; + start_transfer(common->fsg, common->fsg->bulk_out, + bh->outreq, &bh->outreq_busy, &bh->state); + return true; +} static int sleep_thread(struct fsg_common *common) { @@ -739,16 +741,20 @@ static int do_read(struct fsg_common *common) unsigned int partial_page; ssize_t nread; - /* Get the starting Logical Block Address and check that it's - * not too big */ + /* + * Get the starting Logical Block Address and check that it's + * not too big. + */ if (common->cmnd[0] == READ_6) lba = get_unaligned_be24(&common->cmnd[1]); else { lba = get_unaligned_be32(&common->cmnd[2]); - /* We allow DPO (Disable Page Out = don't save data in the + /* + * We allow DPO (Disable Page Out = don't save data in the * cache) and FUA (Force Unit Access = don't read from the - * cache), but we don't implement them. */ + * cache), but we don't implement them. + */ if ((common->cmnd[1] & ~0x18) != 0) { curlun->sense_data = SS_INVALID_FIELD_IN_CDB; return -EINVAL; @@ -766,22 +772,23 @@ static int do_read(struct fsg_common *common) return -EIO; /* No default reply */ for (;;) { - - /* Figure out how much we need to read: + /* + * Figure out how much we need to read: * Try to read the remaining amount. * But don't read more than the buffer size. * And don't try to read past the end of the file. * Finally, if we're not at a page boundary, don't read past * the next page. * If this means reading 0 then we were asked to read past - * the end of file. */ + * the end of file. + */ amount = min(amount_left, FSG_BUFLEN); - amount = min((loff_t) amount, - curlun->file_length - file_offset); + amount = min((loff_t)amount, + curlun->file_length - file_offset); partial_page = file_offset & (PAGE_CACHE_SIZE - 1); if (partial_page > 0) - amount = min(amount, (unsigned int) PAGE_CACHE_SIZE - - partial_page); + amount = min(amount, (unsigned int)PAGE_CACHE_SIZE - + partial_page); /* Wait for the next buffer to become available */ bh = common->next_buffhd_to_fill; @@ -791,8 +798,10 @@ static int do_read(struct fsg_common *common) return rc; } - /* If we were asked to read past the end of file, - * end with an empty buffer. */ + /* + * If we were asked to read past the end of file, + * end with an empty buffer. + */ if (amount == 0) { curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; @@ -806,21 +815,19 @@ static int do_read(struct fsg_common *common) /* Perform the read */ file_offset_tmp = file_offset; nread = vfs_read(curlun->filp, - (char __user *) bh->buf, - amount, &file_offset_tmp); + (char __user *)bh->buf, + amount, &file_offset_tmp); VLDBG(curlun, "file read %u @ %llu -> %d\n", amount, - (unsigned long long) file_offset, - (int) nread); + (unsigned long long)file_offset, (int)nread); if (signal_pending(current)) return -EINTR; if (nread < 0) { - LDBG(curlun, "error in file read: %d\n", - (int) nread); + LDBG(curlun, "error in file read: %d\n", (int)nread); nread = 0; } else if (nread < amount) { LDBG(curlun, "partial file read: %d/%u\n", - (int) nread, amount); + (int)nread, amount); nread -= (nread & 511); /* Round down to a block */ } file_offset += nread; @@ -842,10 +849,8 @@ static int do_read(struct fsg_common *common) /* Send this buffer and go read some more */ bh->inreq->zero = 0; - START_TRANSFER_OR(common, bulk_in, bh->inreq, - &bh->inreq_busy, &bh->state) - /* Don't know what to do if - * common->fsg is NULL */ + if (!start_in_transfer(common, bh)) + /* Don't know what to do if common->fsg is NULL */ return -EIO; common->next_buffhd_to_fill = bh->next; } @@ -877,17 +882,21 @@ static int do_write(struct fsg_common *common) curlun->filp->f_flags &= ~O_SYNC; /* Default is not to wait */ spin_unlock(&curlun->filp->f_lock); - /* Get the starting Logical Block Address and check that it's - * not too big */ + /* + * Get the starting Logical Block Address and check that it's + * not too big + */ if (common->cmnd[0] == WRITE_6) lba = get_unaligned_be24(&common->cmnd[1]); else { lba = get_unaligned_be32(&common->cmnd[2]); - /* We allow DPO (Disable Page Out = don't save data in the + /* + * We allow DPO (Disable Page Out = don't save data in the * cache) and FUA (Force Unit Access = write directly to the * medium). We don't implement DPO; we implement FUA by - * performing synchronous output. */ + * performing synchronous output. + */ if (common->cmnd[1] & ~0x18) { curlun->sense_data = SS_INVALID_FIELD_IN_CDB; return -EINVAL; @@ -915,7 +924,8 @@ static int do_write(struct fsg_common *common) bh = common->next_buffhd_to_fill; if (bh->state == BUF_STATE_EMPTY && get_some_more) { - /* Figure out how much we want to get: + /* + * Figure out how much we want to get: * Try to get the remaining amount. * But don't get more than the buffer size. * And don't try to go past the end of the file. @@ -923,14 +933,15 @@ static int do_write(struct fsg_common *common) * don't go past the next page. * If this means getting 0, then we were asked * to write past the end of file. - * Finally, round down to a block boundary. */ + * Finally, round down to a block boundary. + */ amount = min(amount_left_to_req, FSG_BUFLEN); - amount = min((loff_t) amount, curlun->file_length - - usb_offset); + amount = min((loff_t)amount, + curlun->file_length - usb_offset); partial_page = usb_offset & (PAGE_CACHE_SIZE - 1); if (partial_page > 0) amount = min(amount, - (unsigned int) PAGE_CACHE_SIZE - partial_page); + (unsigned int)PAGE_CACHE_SIZE - partial_page); if (amount == 0) { get_some_more = 0; @@ -940,11 +951,13 @@ static int do_write(struct fsg_common *common) curlun->info_valid = 1; continue; } - amount -= (amount & 511); + amount -= amount & 511; if (amount == 0) { - /* Why were we were asked to transfer a - * partial block? */ + /* + * Why were we were asked to transfer a + * partial block? + */ get_some_more = 0; continue; } @@ -956,15 +969,15 @@ static int do_write(struct fsg_common *common) if (amount_left_to_req == 0) get_some_more = 0; - /* amount is always divisible by 512, hence by - * the bulk-out maxpacket size */ + /* + * amount is always divisible by 512, hence by + * the bulk-out maxpacket size + */ bh->outreq->length = amount; bh->bulk_out_intended_length = amount; bh->outreq->short_not_ok = 1; - START_TRANSFER_OR(common, bulk_out, bh->outreq, - &bh->outreq_busy, &bh->state) - /* Don't know what to do if - * common->fsg is NULL */ + if (!start_out_transfer(common, bh)) + /* Dunno what to do if common->fsg is NULL */ return -EIO; common->next_buffhd_to_fill = bh->next; continue; @@ -990,30 +1003,29 @@ static int do_write(struct fsg_common *common) amount = bh->outreq->actual; if (curlun->file_length - file_offset < amount) { LERROR(curlun, - "write %u @ %llu beyond end %llu\n", - amount, (unsigned long long) file_offset, - (unsigned long long) curlun->file_length); + "write %u @ %llu beyond end %llu\n", + amount, (unsigned long long)file_offset, + (unsigned long long)curlun->file_length); amount = curlun->file_length - file_offset; } /* Perform the write */ file_offset_tmp = file_offset; nwritten = vfs_write(curlun->filp, - (char __user *) bh->buf, - amount, &file_offset_tmp); + (char __user *)bh->buf, + amount, &file_offset_tmp); VLDBG(curlun, "file write %u @ %llu -> %d\n", amount, - (unsigned long long) file_offset, - (int) nwritten); + (unsigned long long)file_offset, (int)nwritten); if (signal_pending(current)) return -EINTR; /* Interrupted! */ if (nwritten < 0) { LDBG(curlun, "error in file write: %d\n", - (int) nwritten); + (int)nwritten); nwritten = 0; } else if (nwritten < amount) { LDBG(curlun, "partial file write: %d/%u\n", - (int) nwritten, amount); + (int)nwritten, amount); nwritten -= (nwritten & 511); /* Round down to a block */ } @@ -1086,16 +1098,20 @@ static int do_verify(struct fsg_common *common) unsigned int amount; ssize_t nread; - /* Get the starting Logical Block Address and check that it's - * not too big */ + /* + * Get the starting Logical Block Address and check that it's + * not too big. + */ lba = get_unaligned_be32(&common->cmnd[2]); if (lba >= curlun->num_sectors) { curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; return -EINVAL; } - /* We allow DPO (Disable Page Out = don't save data in the - * cache) but we don't implement it. */ + /* + * We allow DPO (Disable Page Out = don't save data in the + * cache) but we don't implement it. + */ if (common->cmnd[1] & ~0x10) { curlun->sense_data = SS_INVALID_FIELD_IN_CDB; return -EINVAL; @@ -1120,16 +1136,17 @@ static int do_verify(struct fsg_common *common) /* Just try to read the requested blocks */ while (amount_left > 0) { - - /* Figure out how much we need to read: + /* + * Figure out how much we need to read: * Try to read the remaining amount, but not more than * the buffer size. * And don't try to read past the end of the file. * If this means reading 0 then we were asked to read - * past the end of file. */ + * past the end of file. + */ amount = min(amount_left, FSG_BUFLEN); - amount = min((loff_t) amount, - curlun->file_length - file_offset); + amount = min((loff_t)amount, + curlun->file_length - file_offset); if (amount == 0) { curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; @@ -1150,13 +1167,12 @@ static int do_verify(struct fsg_common *common) return -EINTR; if (nread < 0) { - LDBG(curlun, "error in file verify: %d\n", - (int) nread); + LDBG(curlun, "error in file verify: %d\n", (int)nread); nread = 0; } else if (nread < amount) { LDBG(curlun, "partial file verify: %d/%u\n", - (int) nread, amount); - nread -= (nread & 511); /* Round down to a sector */ + (int)nread, amount); + nread -= nread & 511; /* Round down to a sector */ } if (nread == 0) { curlun->sense_data = SS_UNRECOVERED_READ_ERROR; @@ -1198,7 +1214,6 @@ static int do_inquiry(struct fsg_common *common, struct fsg_buffhd *bh) return 36; } - static int do_request_sense(struct fsg_common *common, struct fsg_buffhd *bh) { struct fsg_lun *curlun = common->curlun; @@ -1252,13 +1267,12 @@ static int do_request_sense(struct fsg_common *common, struct fsg_buffhd *bh) return 18; } - static int do_read_capacity(struct fsg_common *common, struct fsg_buffhd *bh) { struct fsg_lun *curlun = common->curlun; u32 lba = get_unaligned_be32(&common->cmnd[2]); int pmi = common->cmnd[8]; - u8 *buf = (u8 *) bh->buf; + u8 *buf = (u8 *)bh->buf; /* Check the PMI and LBA fields */ if (pmi > 1 || (pmi == 0 && lba != 0)) { @@ -1272,13 +1286,12 @@ static int do_read_capacity(struct fsg_common *common, struct fsg_buffhd *bh) return 8; } - static int do_read_header(struct fsg_common *common, struct fsg_buffhd *bh) { struct fsg_lun *curlun = common->curlun; int msf = common->cmnd[1] & 0x02; u32 lba = get_unaligned_be32(&common->cmnd[2]); - u8 *buf = (u8 *) bh->buf; + u8 *buf = (u8 *)bh->buf; if (common->cmnd[1] & ~0x02) { /* Mask away MSF */ curlun->sense_data = SS_INVALID_FIELD_IN_CDB; @@ -1295,13 +1308,12 @@ static int do_read_header(struct fsg_common *common, struct fsg_buffhd *bh) return 8; } - static int do_read_toc(struct fsg_common *common, struct fsg_buffhd *bh) { struct fsg_lun *curlun = common->curlun; int msf = common->cmnd[1] & 0x02; int start_track = common->cmnd[6]; - u8 *buf = (u8 *) bh->buf; + u8 *buf = (u8 *)bh->buf; if ((common->cmnd[1] & ~0x02) != 0 || /* Mask away MSF */ start_track > 1) { @@ -1323,7 +1335,6 @@ static int do_read_toc(struct fsg_common *common, struct fsg_buffhd *bh) return 20; } - static int do_mode_sense(struct fsg_common *common, struct fsg_buffhd *bh) { struct fsg_lun *curlun = common->curlun; @@ -1348,10 +1359,12 @@ static int do_mode_sense(struct fsg_common *common, struct fsg_buffhd *bh) changeable_values = (pc == 1); all_pages = (page_code == 0x3f); - /* Write the mode parameter header. Fixed values are: default + /* + * Write the mode parameter header. Fixed values are: default * medium type, no cache control (DPOFUA), and no block descriptors. * The only variable value is the WriteProtect bit. We will fill in - * the mode data length later. */ + * the mode data length later. + */ memset(buf, 0, 8); if (mscmnd == MODE_SENSE) { buf[2] = (curlun->ro ? 0x80 : 0x00); /* WP, DPOFUA */ @@ -1365,8 +1378,10 @@ static int do_mode_sense(struct fsg_common *common, struct fsg_buffhd *bh) /* No block descriptors */ - /* The mode pages, in numerical order. The only page we support - * is the Caching page. */ + /* + * The mode pages, in numerical order. The only page we support + * is the Caching page. + */ if (page_code == 0x08 || all_pages) { valid_page = 1; buf[0] = 0x08; /* Page code */ @@ -1388,8 +1403,10 @@ static int do_mode_sense(struct fsg_common *common, struct fsg_buffhd *bh) buf += 12; } - /* Check that a valid page was requested and the mode data length - * isn't too long. */ + /* + * Check that a valid page was requested and the mode data length + * isn't too long. + */ len = buf - buf0; if (!valid_page || len > limit) { curlun->sense_data = SS_INVALID_FIELD_IN_CDB; @@ -1404,7 +1421,6 @@ static int do_mode_sense(struct fsg_common *common, struct fsg_buffhd *bh) return len; } - static int do_start_stop(struct fsg_common *common) { struct fsg_lun *curlun = common->curlun; @@ -1424,8 +1440,10 @@ static int do_start_stop(struct fsg_common *common) loej = common->cmnd[4] & 0x02; start = common->cmnd[4] & 0x01; - /* Our emulation doesn't support mounting; the medium is - * available for use as soon as it is loaded. */ + /* + * Our emulation doesn't support mounting; the medium is + * available for use as soon as it is loaded. + */ if (start) { if (!fsg_lun_is_open(curlun)) { curlun->sense_data = SS_MEDIUM_NOT_PRESENT; @@ -1466,7 +1484,6 @@ static int do_start_stop(struct fsg_common *common) : 0; } - static int do_prevent_allow(struct fsg_common *common) { struct fsg_lun *curlun = common->curlun; @@ -1491,7 +1508,6 @@ static int do_prevent_allow(struct fsg_common *common) return 0; } - static int do_read_format_capacities(struct fsg_common *common, struct fsg_buffhd *bh) { @@ -1509,7 +1525,6 @@ static int do_read_format_capacities(struct fsg_common *common, return 12; } - static int do_mode_select(struct fsg_common *common, struct fsg_buffhd *bh) { struct fsg_lun *curlun = common->curlun; @@ -1591,7 +1606,7 @@ static int pad_with_zeros(struct fsg_dev *fsg) bh->inreq->length = nsend; bh->inreq->zero = 0; start_transfer(fsg, fsg->bulk_in, bh->inreq, - &bh->inreq_busy, &bh->state); + &bh->inreq_busy, &bh->state); bh = fsg->common->next_buffhd_to_fill = bh->next; fsg->common->usb_amount_left -= nsend; nkeep = 0; @@ -1617,7 +1632,7 @@ static int throw_away_data(struct fsg_common *common) /* A short packet or an error ends everything */ if (bh->outreq->actual != bh->outreq->length || - bh->outreq->status != 0) { + bh->outreq->status != 0) { raise_exception(common, FSG_STATE_ABORT_BULK_OUT); return -EINTR; @@ -1631,15 +1646,15 @@ static int throw_away_data(struct fsg_common *common) && common->usb_amount_left > 0) { amount = min(common->usb_amount_left, FSG_BUFLEN); - /* amount is always divisible by 512, hence by - * the bulk-out maxpacket size */ + /* + * amount is always divisible by 512, hence by + * the bulk-out maxpacket size. + */ bh->outreq->length = amount; bh->bulk_out_intended_length = amount; bh->outreq->short_not_ok = 1; - START_TRANSFER_OR(common, bulk_out, bh->outreq, - &bh->outreq_busy, &bh->state) - /* Don't know what to do if - * common->fsg is NULL */ + if (!start_out_transfer(common, bh)) + /* Dunno what to do if common->fsg is NULL */ return -EIO; common->next_buffhd_to_fill = bh->next; common->usb_amount_left -= amount; @@ -1654,7 +1669,6 @@ static int throw_away_data(struct fsg_common *common) return 0; } - static int finish_reply(struct fsg_common *common) { struct fsg_buffhd *bh = common->next_buffhd_to_fill; @@ -1664,10 +1678,12 @@ static int finish_reply(struct fsg_common *common) case DATA_DIR_NONE: break; /* Nothing to send */ - /* If we don't know whether the host wants to read or write, + /* + * If we don't know whether the host wants to read or write, * this must be CB or CBI with an unknown command. We mustn't * try to send or receive any data. So stall both bulk pipes - * if we can and wait for a reset. */ + * if we can and wait for a reset. + */ case DATA_DIR_UNKNOWN: if (!common->can_stall) { /* Nothing */ @@ -1688,18 +1704,18 @@ static int finish_reply(struct fsg_common *common) /* If there's no residue, simply send the last buffer */ } else if (common->residue == 0) { bh->inreq->zero = 0; - START_TRANSFER_OR(common, bulk_in, bh->inreq, - &bh->inreq_busy, &bh->state) + if (!start_in_transfer(common, bh)) return -EIO; common->next_buffhd_to_fill = bh->next; - /* For Bulk-only, if we're allowed to stall then send the + /* + * For Bulk-only, if we're allowed to stall then send the * short packet and halt the bulk-in endpoint. If we can't - * stall, pad out the remaining data with 0's. */ + * stall, pad out the remaining data with 0's. + */ } else if (common->can_stall) { bh->inreq->zero = 1; - START_TRANSFER_OR(common, bulk_in, bh->inreq, - &bh->inreq_busy, &bh->state) + if (!start_in_transfer(common, bh)) /* Don't know what to do if * common->fsg is NULL */ rc = -EIO; @@ -1714,8 +1730,10 @@ static int finish_reply(struct fsg_common *common) } break; - /* We have processed all we want from the data the host has sent. - * There may still be outstanding bulk-out requests. */ + /* + * We have processed all we want from the data the host has sent. + * There may still be outstanding bulk-out requests. + */ case DATA_DIR_FROM_HOST: if (common->residue == 0) { /* Nothing to receive */ @@ -1725,12 +1743,14 @@ static int finish_reply(struct fsg_common *common) raise_exception(common, FSG_STATE_ABORT_BULK_OUT); rc = -EINTR; - /* We haven't processed all the incoming data. Even though + /* + * We haven't processed all the incoming data. Even though * we may be allowed to stall, doing so would cause a race. * The controller may already have ACK'ed all the remaining * bulk-out packets, in which case the host wouldn't see a * STALL. Not realizing the endpoint was halted, it wouldn't - * clear the halt -- leading to problems later on. */ + * clear the halt -- leading to problems later on. + */ #if 0 } else if (common->can_stall) { if (fsg_is_set(common)) @@ -1740,8 +1760,10 @@ static int finish_reply(struct fsg_common *common) rc = -EINTR; #endif - /* We can't stall. Read in the excess data and throw it - * all away. */ + /* + * We can't stall. Read in the excess data and throw it + * all away. + */ } else { rc = throw_away_data(common); } @@ -1750,7 +1772,6 @@ static int finish_reply(struct fsg_common *common) return rc; } - static int send_status(struct fsg_common *common) { struct fsg_lun *curlun = common->curlun; @@ -1798,8 +1819,7 @@ static int send_status(struct fsg_common *common) bh->inreq->length = USB_BULK_CS_WRAP_LEN; bh->inreq->zero = 0; - START_TRANSFER_OR(common, bulk_in, bh->inreq, - &bh->inreq_busy, &bh->state) + if (!start_in_transfer(common, bh)) /* Don't know what to do if common->fsg is NULL */ return -EIO; @@ -1810,11 +1830,13 @@ static int send_status(struct fsg_common *common) /*-------------------------------------------------------------------------*/ -/* Check whether the command is properly formed and whether its data size - * and direction agree with the values we already have. */ +/* + * Check whether the command is properly formed and whether its data size + * and direction agree with the values we already have. + */ static int check_command(struct fsg_common *common, int cmnd_size, - enum data_direction data_dir, unsigned int mask, - int needs_medium, const char *name) + enum data_direction data_dir, unsigned int mask, + int needs_medium, const char *name) { int i; int lun = common->cmnd[1] >> 5; @@ -1825,19 +1847,23 @@ static int check_command(struct fsg_common *common, int cmnd_size, hdlen[0] = 0; if (common->data_dir != DATA_DIR_UNKNOWN) sprintf(hdlen, ", H%c=%u", dirletter[(int) common->data_dir], - common->data_size); + common->data_size); VDBG(common, "SCSI command: %s; Dc=%d, D%c=%u; Hc=%d%s\n", name, cmnd_size, dirletter[(int) data_dir], common->data_size_from_cmnd, common->cmnd_size, hdlen); - /* We can't reply at all until we know the correct data direction - * and size. */ + /* + * We can't reply at all until we know the correct data direction + * and size. + */ if (common->data_size_from_cmnd == 0) data_dir = DATA_DIR_NONE; if (common->data_size < common->data_size_from_cmnd) { - /* Host data size < Device data size is a phase error. + /* + * Host data size < Device data size is a phase error. * Carry out the command, but only transfer as much as - * we are allowed. */ + * we are allowed. + */ common->data_size_from_cmnd = common->data_size; common->phase_error = 1; } @@ -1845,8 +1871,7 @@ static int check_command(struct fsg_common *common, int cmnd_size, common->usb_amount_left = common->data_size; /* Conflicting data directions is a phase error */ - if (common->data_dir != data_dir - && common->data_size_from_cmnd > 0) { + if (common->data_dir != data_dir && common->data_size_from_cmnd > 0) { common->phase_error = 1; return -EINVAL; } @@ -1854,7 +1879,8 @@ static int check_command(struct fsg_common *common, int cmnd_size, /* Verify the length of the command itself */ if (cmnd_size != common->cmnd_size) { - /* Special case workaround: There are plenty of buggy SCSI + /* + * Special case workaround: There are plenty of buggy SCSI * implementations. Many have issues with cbw->Length * field passing a wrong command size. For those cases we * always try to work around the problem by using the length @@ -1896,8 +1922,10 @@ static int check_command(struct fsg_common *common, int cmnd_size, curlun = NULL; common->bad_lun_okay = 0; - /* INQUIRY and REQUEST SENSE commands are explicitly allowed - * to use unsupported LUNs; all others may not. */ + /* + * INQUIRY and REQUEST SENSE commands are explicitly allowed + * to use unsupported LUNs; all others may not. + */ if (common->cmnd[0] != INQUIRY && common->cmnd[0] != REQUEST_SENSE) { DBG(common, "unsupported LUN %d\n", common->lun); @@ -1905,11 +1933,13 @@ static int check_command(struct fsg_common *common, int cmnd_size, } } - /* If a unit attention condition exists, only INQUIRY and - * REQUEST SENSE commands are allowed; anything else must fail. */ + /* + * If a unit attention condition exists, only INQUIRY and + * REQUEST SENSE commands are allowed; anything else must fail. + */ if (curlun && curlun->unit_attention_data != SS_NO_SENSE && - common->cmnd[0] != INQUIRY && - common->cmnd[0] != REQUEST_SENSE) { + common->cmnd[0] != INQUIRY && + common->cmnd[0] != REQUEST_SENSE) { curlun->sense_data = curlun->unit_attention_data; curlun->unit_attention_data = SS_NO_SENSE; return -EINVAL; @@ -1935,7 +1965,6 @@ static int check_command(struct fsg_common *common, int cmnd_size, return 0; } - static int do_scsi_command(struct fsg_common *common) { struct fsg_buffhd *bh; @@ -2123,8 +2152,10 @@ static int do_scsi_command(struct fsg_common *common) "TEST UNIT READY"); break; - /* Although optional, this command is used by MS-Windows. We - * support a minimal version: BytChk must be 0. */ + /* + * Although optional, this command is used by MS-Windows. We + * support a minimal version: BytChk must be 0. + */ case VERIFY: common->data_size_from_cmnd = 0; reply = check_command(common, 10, DATA_DIR_NONE, @@ -2164,10 +2195,12 @@ static int do_scsi_command(struct fsg_common *common) reply = do_write(common); break; - /* Some mandatory commands that we recognize but don't implement. + /* + * Some mandatory commands that we recognize but don't implement. * They don't mean much in this setting. It's left as an exercise * for anyone interested to implement RESERVE and RELEASE in terms - * of Posix locks. */ + * of Posix locks. + */ case FORMAT_UNIT: case RELEASE: case RESERVE: @@ -2195,7 +2228,7 @@ unknown_cmnd: if (reply == -EINVAL) reply = 0; /* Error reply length */ if (reply >= 0 && common->data_dir == DATA_DIR_TO_HOST) { - reply = min((u32) reply, common->data_size_from_cmnd); + reply = min((u32)reply, common->data_size_from_cmnd); bh->inreq->length = reply; bh->state = BUF_STATE_FULL; common->residue -= reply; @@ -2225,7 +2258,8 @@ static int received_cbw(struct fsg_dev *fsg, struct fsg_buffhd *bh) req->actual, le32_to_cpu(cbw->Signature)); - /* The Bulk-only spec says we MUST stall the IN endpoint + /* + * The Bulk-only spec says we MUST stall the IN endpoint * (6.6.1), so it's unavoidable. It also says we must * retain this state until the next reset, but there's * no way to tell the controller driver it should ignore @@ -2233,7 +2267,8 @@ static int received_cbw(struct fsg_dev *fsg, struct fsg_buffhd *bh) * * We aren't required to halt the OUT endpoint; instead * we can simply accept and discard any data received - * until the next reset. */ + * until the next reset. + */ wedge_bulk_in_endpoint(fsg); set_bit(IGNORE_BULK_OUT, &fsg->atomic_bitflags); return -EINVAL; @@ -2246,8 +2281,10 @@ static int received_cbw(struct fsg_dev *fsg, struct fsg_buffhd *bh) "cmdlen %u\n", cbw->Lun, cbw->Flags, cbw->Length); - /* We can do anything we want here, so let's stall the - * bulk pipes if we are allowed to. */ + /* + * We can do anything we want here, so let's stall the + * bulk pipes if we are allowed to. + */ if (common->can_stall) { fsg_set_halt(fsg, fsg->bulk_out); halt_bulk_in_endpoint(fsg); @@ -2270,7 +2307,6 @@ static int received_cbw(struct fsg_dev *fsg, struct fsg_buffhd *bh) return 0; } - static int get_next_command(struct fsg_common *common) { struct fsg_buffhd *bh; @@ -2287,14 +2323,15 @@ static int get_next_command(struct fsg_common *common) /* Queue a request to read a Bulk-only CBW */ set_bulk_out_req_length(common, bh, USB_BULK_CB_WRAP_LEN); bh->outreq->short_not_ok = 1; - START_TRANSFER_OR(common, bulk_out, bh->outreq, - &bh->outreq_busy, &bh->state) + if (!start_out_transfer(common, bh)) /* Don't know what to do if common->fsg is NULL */ return -EIO; - /* We will drain the buffer in software, which means we + /* + * We will drain the buffer in software, which means we * can reuse it for the next filling. No need to advance - * next_buffhd_to_fill. */ + * next_buffhd_to_fill. + */ /* Wait for the CBW to arrive */ while (bh->state != BUF_STATE_FULL) { @@ -2425,7 +2462,6 @@ reset: /****************************** ALT CONFIGS ******************************/ - static int fsg_set_alt(struct usb_function *f, unsigned intf, unsigned alt) { struct fsg_dev *fsg = fsg_from_func(f); @@ -2453,8 +2489,10 @@ static void handle_exception(struct fsg_common *common) struct fsg_lun *curlun; unsigned int exception_req_tag; - /* Clear the existing signals. Anything but SIGUSR1 is converted - * into a high-priority EXIT exception. */ + /* + * Clear the existing signals. Anything but SIGUSR1 is converted + * into a high-priority EXIT exception. + */ for (;;) { int sig = dequeue_signal_lock(current, ¤t->blocked, &info); @@ -2498,8 +2536,10 @@ static void handle_exception(struct fsg_common *common) usb_ep_fifo_flush(common->fsg->bulk_out); } - /* Reset the I/O buffer states and pointers, the SCSI - * state, and the exception. Then invoke the handler. */ + /* + * Reset the I/O buffer states and pointers, the SCSI + * state, and the exception. Then invoke the handler. + */ spin_lock_irq(&common->lock); for (i = 0; i < FSG_NUM_BUFFERS; ++i) { @@ -2537,9 +2577,11 @@ static void handle_exception(struct fsg_common *common) break; case FSG_STATE_RESET: - /* In case we were forced against our will to halt a + /* + * In case we were forced against our will to halt a * bulk endpoint, clear the halt now. (The SuperH UDC - * requires this.) */ + * requires this.) + */ if (!fsg_is_set(common)) break; if (test_and_clear_bit(IGNORE_BULK_OUT, @@ -2549,9 +2591,11 @@ static void handle_exception(struct fsg_common *common) if (common->ep0_req_tag == exception_req_tag) ep0_queue(common); /* Complete the status stage */ - /* Technically this should go here, but it would only be + /* + * Technically this should go here, but it would only be * a waste of time. Ditto for the INTERFACE_CHANGE and - * CONFIG_CHANGE cases. */ + * CONFIG_CHANGE cases. + */ /* for (i = 0; i < common->nluns; ++i) */ /* common->luns[i].unit_attention_data = */ /* SS_RESET_OCCURRED; */ @@ -2586,8 +2630,10 @@ static int fsg_main_thread(void *common_) { struct fsg_common *common = common_; - /* Allow the thread to be killed by a signal, but set the signal mask - * to block everything but INT, TERM, KILL, and USR1. */ + /* + * Allow the thread to be killed by a signal, but set the signal mask + * to block everything but INT, TERM, KILL, and USR1. + */ allow_signal(SIGINT); allow_signal(SIGTERM); allow_signal(SIGKILL); @@ -2596,9 +2642,11 @@ static int fsg_main_thread(void *common_) /* Allow the thread to be frozen */ set_freezable(); - /* Arrange for userspace references to be interpreted as kernel + /* + * Arrange for userspace references to be interpreted as kernel * pointers. That way we can pass a kernel pointer to a routine - * that expects a __user pointer and it will work okay. */ + * that expects a __user pointer and it will work okay. + */ set_fs(get_ds()); /* The main loop */ @@ -2658,7 +2706,7 @@ static int fsg_main_thread(void *common_) up_write(&common->filesem); } - /* Let the unbind and cleanup routines know the thread has exited */ + /* Let fsg_unbind() know the thread has exited */ complete_and_exit(&common->thread_notifier, 0); } @@ -2690,7 +2738,6 @@ static inline void fsg_common_put(struct fsg_common *common) kref_put(&common->ref, fsg_common_release); } - static struct fsg_common *fsg_common_init(struct fsg_common *common, struct usb_composite_dev *cdev, struct fsg_config *cfg) @@ -2736,8 +2783,10 @@ static struct fsg_common *fsg_common_init(struct fsg_common *common, fsg_intf_desc.iInterface = rc; } - /* Create the LUNs, open their backing files, and register the - * LUN devices in sysfs. */ + /* + * Create the LUNs, open their backing files, and register the + * LUN devices in sysfs. + */ curlun = kzalloc(nluns * sizeof *curlun, GFP_KERNEL); if (unlikely(!curlun)) { rc = -ENOMEM; @@ -2765,6 +2814,7 @@ static struct fsg_common *fsg_common_init(struct fsg_common *common, if (rc) { INFO(common, "failed to register LUN%d: %d\n", i, rc); common->nluns = i; + put_device(&curlun->dev); goto error_release; } @@ -2790,7 +2840,6 @@ static struct fsg_common *fsg_common_init(struct fsg_common *common, } common->nluns = nluns; - /* Data buffers cyclic list */ bh = common->buffhds; i = FSG_NUM_BUFFERS; @@ -2807,7 +2856,6 @@ buffhds_first_it: } while (--i); bh->next = common->buffhds; - /* Prepare inquiryString */ if (cfg->release != 0xffff) { i = cfg->release; @@ -2821,41 +2869,35 @@ buffhds_first_it: i = 0x0399; } } -#define OR(x, y) ((x) ? (x) : (y)) snprintf(common->inquiry_string, sizeof common->inquiry_string, - "%-8s%-16s%04x", - OR(cfg->vendor_name, "Linux "), + "%-8s%-16s%04x", cfg->vendor_name ?: "Linux", /* Assume product name dependent on the first LUN */ - OR(cfg->product_name, common->luns->cdrom + cfg->product_name ?: (common->luns->cdrom ? "File-Stor Gadget" - : "File-CD Gadget "), + : "File-CD Gadget"), i); - - /* Some peripheral controllers are known not to be able to + /* + * Some peripheral controllers are known not to be able to * halt bulk endpoints correctly. If one of them is present, * disable stalls. */ common->can_stall = cfg->can_stall && !(gadget_is_at91(common->gadget)); - spin_lock_init(&common->lock); kref_init(&common->ref); - /* Tell the thread to start working */ common->thread_task = kthread_create(fsg_main_thread, common, - OR(cfg->thread_name, "file-storage")); + cfg->thread_name ?: "file-storage"); if (IS_ERR(common->thread_task)) { rc = PTR_ERR(common->thread_task); goto error_release; } init_completion(&common->thread_notifier); init_waitqueue_head(&common->fsg_wait); -#undef OR - /* Information */ INFO(common, FSG_DRIVER_DESC ", version: " FSG_DRIVER_VERSION "\n"); @@ -2889,18 +2931,15 @@ buffhds_first_it: return common; - error_luns: common->nluns = i + 1; error_release: common->state = FSG_STATE_TERMINATED; /* The thread is dead */ - /* Call fsg_common_release() directly, ref might be not - * initialised */ + /* Call fsg_common_release() directly, ref might be not initialised. */ fsg_common_release(&common->ref); return ERR_PTR(rc); } - static void fsg_common_release(struct kref *ref) { struct fsg_common *common = container_of(ref, struct fsg_common, ref); @@ -2909,9 +2948,6 @@ static void fsg_common_release(struct kref *ref) if (common->state != FSG_STATE_TERMINATED) { raise_exception(common, FSG_STATE_EXIT); wait_for_completion(&common->thread_notifier); - - /* The cleanup routine waits for this completion also */ - complete(&common->thread_notifier); } if (likely(common->luns)) { @@ -2945,7 +2981,6 @@ static void fsg_common_release(struct kref *ref) /*-------------------------------------------------------------------------*/ - static void fsg_unbind(struct usb_configuration *c, struct usb_function *f) { struct fsg_dev *fsg = fsg_from_func(f); @@ -2965,7 +3000,6 @@ static void fsg_unbind(struct usb_configuration *c, struct usb_function *f) kfree(fsg); } - static int fsg_bind(struct usb_configuration *c, struct usb_function *f) { struct fsg_dev *fsg = fsg_from_func(f); @@ -3048,11 +3082,13 @@ static int fsg_bind_config(struct usb_composite_dev *cdev, fsg->function.disable = fsg_disable; fsg->common = common; - /* Our caller holds a reference to common structure so we + /* + * Our caller holds a reference to common structure so we * don't have to be worry about it being freed until we return * from this function. So instead of incrementing counter now * and decrement in error recovery we increment it only when - * call to usb_add_function() was successful. */ + * call to usb_add_function() was successful. + */ rc = usb_add_function(c, &fsg->function); if (unlikely(rc)) @@ -3063,8 +3099,7 @@ static int fsg_bind_config(struct usb_composite_dev *cdev, } static inline int __deprecated __maybe_unused -fsg_add(struct usb_composite_dev *cdev, - struct usb_configuration *c, +fsg_add(struct usb_composite_dev *cdev, struct usb_configuration *c, struct fsg_common *common) { return fsg_bind_config(cdev, c, common); @@ -3073,7 +3108,6 @@ fsg_add(struct usb_composite_dev *cdev, /************************* Module parameters *************************/ - struct fsg_module_parameters { char *file[FSG_MAX_LUNS]; int ro[FSG_MAX_LUNS]; @@ -3087,7 +3121,6 @@ struct fsg_module_parameters { int stall; /* can_stall */ }; - #define _FSG_MODULE_PARAM_ARRAY(prefix, params, name, type, desc) \ module_param_array_named(prefix ## name, params.name, type, \ &prefix ## params.name ## _count, \ @@ -3115,7 +3148,6 @@ struct fsg_module_parameters { _FSG_MODULE_PARAM(prefix, params, stall, bool, \ "false to prevent bulk stalls") - static void fsg_config_from_params(struct fsg_config *cfg, const struct fsg_module_parameters *params) diff --git a/drivers/usb/gadget/f_ncm.c b/drivers/usb/gadget/f_ncm.c new file mode 100644 index 000000000000..130eee678c8b --- /dev/null +++ b/drivers/usb/gadget/f_ncm.c @@ -0,0 +1,1407 @@ +/* + * f_ncm.c -- USB CDC Network (NCM) link function driver + * + * Copyright (C) 2010 Nokia Corporation + * Contact: Yauheni Kaliuta <yauheni.kaliuta@nokia.com> + * + * The driver borrows from f_ecm.c which is: + * + * Copyright (C) 2003-2005,2008 David Brownell + * Copyright (C) 2008 Nokia Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/kernel.h> +#include <linux/device.h> +#include <linux/etherdevice.h> +#include <linux/crc32.h> + +#include <linux/usb/cdc.h> + +#include "u_ether.h" + +/* + * This function is a "CDC Network Control Model" (CDC NCM) Ethernet link. + * NCM is intended to be used with high-speed network attachments. + * + * Note that NCM requires the use of "alternate settings" for its data + * interface. This means that the set_alt() method has real work to do, + * and also means that a get_alt() method is required. + */ + +/* to trigger crc/non-crc ndp signature */ + +#define NCM_NDP_HDR_CRC_MASK 0x01000000 +#define NCM_NDP_HDR_CRC 0x01000000 +#define NCM_NDP_HDR_NOCRC 0x00000000 + +struct ncm_ep_descs { + struct usb_endpoint_descriptor *in; + struct usb_endpoint_descriptor *out; + struct usb_endpoint_descriptor *notify; +}; + +enum ncm_notify_state { + NCM_NOTIFY_NONE, /* don't notify */ + NCM_NOTIFY_CONNECT, /* issue CONNECT next */ + NCM_NOTIFY_SPEED, /* issue SPEED_CHANGE next */ +}; + +struct f_ncm { + struct gether port; + u8 ctrl_id, data_id; + + char ethaddr[14]; + + struct ncm_ep_descs fs; + struct ncm_ep_descs hs; + + struct usb_ep *notify; + struct usb_endpoint_descriptor *notify_desc; + struct usb_request *notify_req; + u8 notify_state; + bool is_open; + + struct ndp_parser_opts *parser_opts; + bool is_crc; + + /* + * for notification, it is accessed from both + * callback and ethernet open/close + */ + spinlock_t lock; +}; + +static inline struct f_ncm *func_to_ncm(struct usb_function *f) +{ + return container_of(f, struct f_ncm, port.func); +} + +/* peak (theoretical) bulk transfer rate in bits-per-second */ +static inline unsigned ncm_bitrate(struct usb_gadget *g) +{ + if (gadget_is_dualspeed(g) && g->speed == USB_SPEED_HIGH) + return 13 * 512 * 8 * 1000 * 8; + else + return 19 * 64 * 1 * 1000 * 8; +} + +/*-------------------------------------------------------------------------*/ + +/* + * We cannot group frames so use just the minimal size which ok to put + * one max-size ethernet frame. + * If the host can group frames, allow it to do that, 16K is selected, + * because it's used by default by the current linux host driver + */ +#define NTB_DEFAULT_IN_SIZE USB_CDC_NCM_NTB_MIN_IN_SIZE +#define NTB_OUT_SIZE 16384 + +/* + * skbs of size less than that will not be alligned + * to NCM's dwNtbInMaxSize to save bus bandwidth + */ + +#define MAX_TX_NONFIXED (512 * 3) + +#define FORMATS_SUPPORTED (USB_CDC_NCM_NTB16_SUPPORTED | \ + USB_CDC_NCM_NTB32_SUPPORTED) + +static struct usb_cdc_ncm_ntb_parameters ntb_parameters = { + .wLength = sizeof ntb_parameters, + .bmNtbFormatsSupported = cpu_to_le16(FORMATS_SUPPORTED), + .dwNtbInMaxSize = cpu_to_le32(NTB_DEFAULT_IN_SIZE), + .wNdpInDivisor = cpu_to_le16(4), + .wNdpInPayloadRemainder = cpu_to_le16(0), + .wNdpInAlignment = cpu_to_le16(4), + + .dwNtbOutMaxSize = cpu_to_le32(NTB_OUT_SIZE), + .wNdpOutDivisor = cpu_to_le16(4), + .wNdpOutPayloadRemainder = cpu_to_le16(0), + .wNdpOutAlignment = cpu_to_le16(4), +}; + +/* + * Use wMaxPacketSize big enough to fit CDC_NOTIFY_SPEED_CHANGE in one + * packet, to simplify cancellation; and a big transfer interval, to + * waste less bandwidth. + */ + +#define LOG2_STATUS_INTERVAL_MSEC 5 /* 1 << 5 == 32 msec */ +#define NCM_STATUS_BYTECOUNT 16 /* 8 byte header + data */ + +static struct usb_interface_assoc_descriptor ncm_iad_desc __initdata = { + .bLength = sizeof ncm_iad_desc, + .bDescriptorType = USB_DT_INTERFACE_ASSOCIATION, + + /* .bFirstInterface = DYNAMIC, */ + .bInterfaceCount = 2, /* control + data */ + .bFunctionClass = USB_CLASS_COMM, + .bFunctionSubClass = USB_CDC_SUBCLASS_NCM, + .bFunctionProtocol = USB_CDC_PROTO_NONE, + /* .iFunction = DYNAMIC */ +}; + +/* interface descriptor: */ + +static struct usb_interface_descriptor ncm_control_intf __initdata = { + .bLength = sizeof ncm_control_intf, + .bDescriptorType = USB_DT_INTERFACE, + + /* .bInterfaceNumber = DYNAMIC */ + .bNumEndpoints = 1, + .bInterfaceClass = USB_CLASS_COMM, + .bInterfaceSubClass = USB_CDC_SUBCLASS_NCM, + .bInterfaceProtocol = USB_CDC_PROTO_NONE, + /* .iInterface = DYNAMIC */ +}; + +static struct usb_cdc_header_desc ncm_header_desc __initdata = { + .bLength = sizeof ncm_header_desc, + .bDescriptorType = USB_DT_CS_INTERFACE, + .bDescriptorSubType = USB_CDC_HEADER_TYPE, + + .bcdCDC = cpu_to_le16(0x0110), +}; + +static struct usb_cdc_union_desc ncm_union_desc __initdata = { + .bLength = sizeof(ncm_union_desc), + .bDescriptorType = USB_DT_CS_INTERFACE, + .bDescriptorSubType = USB_CDC_UNION_TYPE, + /* .bMasterInterface0 = DYNAMIC */ + /* .bSlaveInterface0 = DYNAMIC */ +}; + +static struct usb_cdc_ether_desc ecm_desc __initdata = { + .bLength = sizeof ecm_desc, + .bDescriptorType = USB_DT_CS_INTERFACE, + .bDescriptorSubType = USB_CDC_ETHERNET_TYPE, + + /* this descriptor actually adds value, surprise! */ + /* .iMACAddress = DYNAMIC */ + .bmEthernetStatistics = cpu_to_le32(0), /* no statistics */ + .wMaxSegmentSize = cpu_to_le16(ETH_FRAME_LEN), + .wNumberMCFilters = cpu_to_le16(0), + .bNumberPowerFilters = 0, +}; + +#define NCAPS (USB_CDC_NCM_NCAP_ETH_FILTER | USB_CDC_NCM_NCAP_CRC_MODE) + +static struct usb_cdc_ncm_desc ncm_desc __initdata = { + .bLength = sizeof ncm_desc, + .bDescriptorType = USB_DT_CS_INTERFACE, + .bDescriptorSubType = USB_CDC_NCM_TYPE, + + .bcdNcmVersion = cpu_to_le16(0x0100), + /* can process SetEthernetPacketFilter */ + .bmNetworkCapabilities = NCAPS, +}; + +/* the default data interface has no endpoints ... */ + +static struct usb_interface_descriptor ncm_data_nop_intf __initdata = { + .bLength = sizeof ncm_data_nop_intf, + .bDescriptorType = USB_DT_INTERFACE, + + .bInterfaceNumber = 1, + .bAlternateSetting = 0, + .bNumEndpoints = 0, + .bInterfaceClass = USB_CLASS_CDC_DATA, + .bInterfaceSubClass = 0, + .bInterfaceProtocol = USB_CDC_NCM_PROTO_NTB, + /* .iInterface = DYNAMIC */ +}; + +/* ... but the "real" data interface has two bulk endpoints */ + +static struct usb_interface_descriptor ncm_data_intf __initdata = { + .bLength = sizeof ncm_data_intf, + .bDescriptorType = USB_DT_INTERFACE, + + .bInterfaceNumber = 1, + .bAlternateSetting = 1, + .bNumEndpoints = 2, + .bInterfaceClass = USB_CLASS_CDC_DATA, + .bInterfaceSubClass = 0, + .bInterfaceProtocol = USB_CDC_NCM_PROTO_NTB, + /* .iInterface = DYNAMIC */ +}; + +/* full speed support: */ + +static struct usb_endpoint_descriptor fs_ncm_notify_desc __initdata = { + .bLength = USB_DT_ENDPOINT_SIZE, + .bDescriptorType = USB_DT_ENDPOINT, + + .bEndpointAddress = USB_DIR_IN, + .bmAttributes = USB_ENDPOINT_XFER_INT, + .wMaxPacketSize = cpu_to_le16(NCM_STATUS_BYTECOUNT), + .bInterval = 1 << LOG2_STATUS_INTERVAL_MSEC, +}; + +static struct usb_endpoint_descriptor fs_ncm_in_desc __initdata = { + .bLength = USB_DT_ENDPOINT_SIZE, + .bDescriptorType = USB_DT_ENDPOINT, + + .bEndpointAddress = USB_DIR_IN, + .bmAttributes = USB_ENDPOINT_XFER_BULK, +}; + +static struct usb_endpoint_descriptor fs_ncm_out_desc __initdata = { + .bLength = USB_DT_ENDPOINT_SIZE, + .bDescriptorType = USB_DT_ENDPOINT, + + .bEndpointAddress = USB_DIR_OUT, + .bmAttributes = USB_ENDPOINT_XFER_BULK, +}; + +static struct usb_descriptor_header *ncm_fs_function[] __initdata = { + (struct usb_descriptor_header *) &ncm_iad_desc, + /* CDC NCM control descriptors */ + (struct usb_descriptor_header *) &ncm_control_intf, + (struct usb_descriptor_header *) &ncm_header_desc, + (struct usb_descriptor_header *) &ncm_union_desc, + (struct usb_descriptor_header *) &ecm_desc, + (struct usb_descriptor_header *) &ncm_desc, + (struct usb_descriptor_header *) &fs_ncm_notify_desc, + /* data interface, altsettings 0 and 1 */ + (struct usb_descriptor_header *) &ncm_data_nop_intf, + (struct usb_descriptor_header *) &ncm_data_intf, + (struct usb_descriptor_header *) &fs_ncm_in_desc, + (struct usb_descriptor_header *) &fs_ncm_out_desc, + NULL, +}; + +/* high speed support: */ + +static struct usb_endpoint_descriptor hs_ncm_notify_desc __initdata = { + .bLength = USB_DT_ENDPOINT_SIZE, + .bDescriptorType = USB_DT_ENDPOINT, + + .bEndpointAddress = USB_DIR_IN, + .bmAttributes = USB_ENDPOINT_XFER_INT, + .wMaxPacketSize = cpu_to_le16(NCM_STATUS_BYTECOUNT), + .bInterval = LOG2_STATUS_INTERVAL_MSEC + 4, +}; +static struct usb_endpoint_descriptor hs_ncm_in_desc __initdata = { + .bLength = USB_DT_ENDPOINT_SIZE, + .bDescriptorType = USB_DT_ENDPOINT, + + .bEndpointAddress = USB_DIR_IN, + .bmAttributes = USB_ENDPOINT_XFER_BULK, + .wMaxPacketSize = cpu_to_le16(512), +}; + +static struct usb_endpoint_descriptor hs_ncm_out_desc __initdata = { + .bLength = USB_DT_ENDPOINT_SIZE, + .bDescriptorType = USB_DT_ENDPOINT, + + .bEndpointAddress = USB_DIR_OUT, + .bmAttributes = USB_ENDPOINT_XFER_BULK, + .wMaxPacketSize = cpu_to_le16(512), +}; + +static struct usb_descriptor_header *ncm_hs_function[] __initdata = { + (struct usb_descriptor_header *) &ncm_iad_desc, + /* CDC NCM control descriptors */ + (struct usb_descriptor_header *) &ncm_control_intf, + (struct usb_descriptor_header *) &ncm_header_desc, + (struct usb_descriptor_header *) &ncm_union_desc, + (struct usb_descriptor_header *) &ecm_desc, + (struct usb_descriptor_header *) &ncm_desc, + (struct usb_descriptor_header *) &hs_ncm_notify_desc, + /* data interface, altsettings 0 and 1 */ + (struct usb_descriptor_header *) &ncm_data_nop_intf, + (struct usb_descriptor_header *) &ncm_data_intf, + (struct usb_descriptor_header *) &hs_ncm_in_desc, + (struct usb_descriptor_header *) &hs_ncm_out_desc, + NULL, +}; + +/* string descriptors: */ + +#define STRING_CTRL_IDX 0 +#define STRING_MAC_IDX 1 +#define STRING_DATA_IDX 2 +#define STRING_IAD_IDX 3 + +static struct usb_string ncm_string_defs[] = { + [STRING_CTRL_IDX].s = "CDC Network Control Model (NCM)", + [STRING_MAC_IDX].s = NULL /* DYNAMIC */, + [STRING_DATA_IDX].s = "CDC Network Data", + [STRING_IAD_IDX].s = "CDC NCM", + { } /* end of list */ +}; + +static struct usb_gadget_strings ncm_string_table = { + .language = 0x0409, /* en-us */ + .strings = ncm_string_defs, +}; + +static struct usb_gadget_strings *ncm_strings[] = { + &ncm_string_table, + NULL, +}; + +/* + * Here are options for NCM Datagram Pointer table (NDP) parser. + * There are 2 different formats: NDP16 and NDP32 in the spec (ch. 3), + * in NDP16 offsets and sizes fields are 1 16bit word wide, + * in NDP32 -- 2 16bit words wide. Also signatures are different. + * To make the parser code the same, put the differences in the structure, + * and switch pointers to the structures when the format is changed. + */ + +struct ndp_parser_opts { + u32 nth_sign; + u32 ndp_sign; + unsigned nth_size; + unsigned ndp_size; + unsigned ndplen_align; + /* sizes in u16 units */ + unsigned dgram_item_len; /* index or length */ + unsigned block_length; + unsigned fp_index; + unsigned reserved1; + unsigned reserved2; + unsigned next_fp_index; +}; + +#define INIT_NDP16_OPTS { \ + .nth_sign = USB_CDC_NCM_NTH16_SIGN, \ + .ndp_sign = USB_CDC_NCM_NDP16_NOCRC_SIGN, \ + .nth_size = sizeof(struct usb_cdc_ncm_nth16), \ + .ndp_size = sizeof(struct usb_cdc_ncm_ndp16), \ + .ndplen_align = 4, \ + .dgram_item_len = 1, \ + .block_length = 1, \ + .fp_index = 1, \ + .reserved1 = 0, \ + .reserved2 = 0, \ + .next_fp_index = 1, \ + } + + +#define INIT_NDP32_OPTS { \ + .nth_sign = USB_CDC_NCM_NTH32_SIGN, \ + .ndp_sign = USB_CDC_NCM_NDP32_NOCRC_SIGN, \ + .nth_size = sizeof(struct usb_cdc_ncm_nth32), \ + .ndp_size = sizeof(struct usb_cdc_ncm_ndp32), \ + .ndplen_align = 8, \ + .dgram_item_len = 2, \ + .block_length = 2, \ + .fp_index = 2, \ + .reserved1 = 1, \ + .reserved2 = 2, \ + .next_fp_index = 2, \ + } + +static struct ndp_parser_opts ndp16_opts = INIT_NDP16_OPTS; +static struct ndp_parser_opts ndp32_opts = INIT_NDP32_OPTS; + +static inline void put_ncm(__le16 **p, unsigned size, unsigned val) +{ + switch (size) { + case 1: + put_unaligned_le16((u16)val, *p); + break; + case 2: + put_unaligned_le32((u32)val, *p); + + break; + default: + BUG(); + } + + *p += size; +} + +static inline unsigned get_ncm(__le16 **p, unsigned size) +{ + unsigned tmp; + + switch (size) { + case 1: + tmp = get_unaligned_le16(*p); + break; + case 2: + tmp = get_unaligned_le32(*p); + break; + default: + BUG(); + } + + *p += size; + return tmp; +} + +/*-------------------------------------------------------------------------*/ + +static inline void ncm_reset_values(struct f_ncm *ncm) +{ + ncm->parser_opts = &ndp16_opts; + ncm->is_crc = false; + ncm->port.cdc_filter = DEFAULT_FILTER; + + /* doesn't make sense for ncm, fixed size used */ + ncm->port.header_len = 0; + + ncm->port.fixed_out_len = le32_to_cpu(ntb_parameters.dwNtbOutMaxSize); + ncm->port.fixed_in_len = NTB_DEFAULT_IN_SIZE; +} + +/* + * Context: ncm->lock held + */ +static void ncm_do_notify(struct f_ncm *ncm) +{ + struct usb_request *req = ncm->notify_req; + struct usb_cdc_notification *event; + struct usb_composite_dev *cdev = ncm->port.func.config->cdev; + __le32 *data; + int status; + + /* notification already in flight? */ + if (!req) + return; + + event = req->buf; + switch (ncm->notify_state) { + case NCM_NOTIFY_NONE: + return; + + case NCM_NOTIFY_CONNECT: + event->bNotificationType = USB_CDC_NOTIFY_NETWORK_CONNECTION; + if (ncm->is_open) + event->wValue = cpu_to_le16(1); + else + event->wValue = cpu_to_le16(0); + event->wLength = 0; + req->length = sizeof *event; + + DBG(cdev, "notify connect %s\n", + ncm->is_open ? "true" : "false"); + ncm->notify_state = NCM_NOTIFY_NONE; + break; + + case NCM_NOTIFY_SPEED: + event->bNotificationType = USB_CDC_NOTIFY_SPEED_CHANGE; + event->wValue = cpu_to_le16(0); + event->wLength = cpu_to_le16(8); + req->length = NCM_STATUS_BYTECOUNT; + + /* SPEED_CHANGE data is up/down speeds in bits/sec */ + data = req->buf + sizeof *event; + data[0] = cpu_to_le32(ncm_bitrate(cdev->gadget)); + data[1] = data[0]; + + DBG(cdev, "notify speed %d\n", ncm_bitrate(cdev->gadget)); + ncm->notify_state = NCM_NOTIFY_CONNECT; + break; + } + event->bmRequestType = 0xA1; + event->wIndex = cpu_to_le16(ncm->ctrl_id); + + ncm->notify_req = NULL; + /* + * In double buffering if there is a space in FIFO, + * completion callback can be called right after the call, + * so unlocking + */ + spin_unlock(&ncm->lock); + status = usb_ep_queue(ncm->notify, req, GFP_ATOMIC); + spin_lock(&ncm->lock); + if (status < 0) { + ncm->notify_req = req; + DBG(cdev, "notify --> %d\n", status); + } +} + +/* + * Context: ncm->lock held + */ +static void ncm_notify(struct f_ncm *ncm) +{ + /* + * NOTE on most versions of Linux, host side cdc-ethernet + * won't listen for notifications until its netdevice opens. + * The first notification then sits in the FIFO for a long + * time, and the second one is queued. + * + * If ncm_notify() is called before the second (CONNECT) + * notification is sent, then it will reset to send the SPEED + * notificaion again (and again, and again), but it's not a problem + */ + ncm->notify_state = NCM_NOTIFY_SPEED; + ncm_do_notify(ncm); +} + +static void ncm_notify_complete(struct usb_ep *ep, struct usb_request *req) +{ + struct f_ncm *ncm = req->context; + struct usb_composite_dev *cdev = ncm->port.func.config->cdev; + struct usb_cdc_notification *event = req->buf; + + spin_lock(&ncm->lock); + switch (req->status) { + case 0: + VDBG(cdev, "Notification %02x sent\n", + event->bNotificationType); + break; + case -ECONNRESET: + case -ESHUTDOWN: + ncm->notify_state = NCM_NOTIFY_NONE; + break; + default: + DBG(cdev, "event %02x --> %d\n", + event->bNotificationType, req->status); + break; + } + ncm->notify_req = req; + ncm_do_notify(ncm); + spin_unlock(&ncm->lock); +} + +static void ncm_ep0out_complete(struct usb_ep *ep, struct usb_request *req) +{ + /* now for SET_NTB_INPUT_SIZE only */ + unsigned in_size; + struct usb_function *f = req->context; + struct f_ncm *ncm = func_to_ncm(f); + struct usb_composite_dev *cdev = ep->driver_data; + + req->context = NULL; + if (req->status || req->actual != req->length) { + DBG(cdev, "Bad control-OUT transfer\n"); + goto invalid; + } + + in_size = get_unaligned_le32(req->buf); + if (in_size < USB_CDC_NCM_NTB_MIN_IN_SIZE || + in_size > le32_to_cpu(ntb_parameters.dwNtbInMaxSize)) { + DBG(cdev, "Got wrong INPUT SIZE (%d) from host\n", in_size); + goto invalid; + } + + ncm->port.fixed_in_len = in_size; + VDBG(cdev, "Set NTB INPUT SIZE %d\n", in_size); + return; + +invalid: + usb_ep_set_halt(ep); + return; +} + +static int ncm_setup(struct usb_function *f, const struct usb_ctrlrequest *ctrl) +{ + struct f_ncm *ncm = func_to_ncm(f); + struct usb_composite_dev *cdev = f->config->cdev; + struct usb_request *req = cdev->req; + int value = -EOPNOTSUPP; + u16 w_index = le16_to_cpu(ctrl->wIndex); + u16 w_value = le16_to_cpu(ctrl->wValue); + u16 w_length = le16_to_cpu(ctrl->wLength); + + /* + * composite driver infrastructure handles everything except + * CDC class messages; interface activation uses set_alt(). + */ + switch ((ctrl->bRequestType << 8) | ctrl->bRequest) { + case ((USB_DIR_OUT | USB_TYPE_CLASS | USB_RECIP_INTERFACE) << 8) + | USB_CDC_SET_ETHERNET_PACKET_FILTER: + /* + * see 6.2.30: no data, wIndex = interface, + * wValue = packet filter bitmap + */ + if (w_length != 0 || w_index != ncm->ctrl_id) + goto invalid; + DBG(cdev, "packet filter %02x\n", w_value); + /* + * REVISIT locking of cdc_filter. This assumes the UDC + * driver won't have a concurrent packet TX irq running on + * another CPU; or that if it does, this write is atomic... + */ + ncm->port.cdc_filter = w_value; + value = 0; + break; + /* + * and optionally: + * case USB_CDC_SEND_ENCAPSULATED_COMMAND: + * case USB_CDC_GET_ENCAPSULATED_RESPONSE: + * case USB_CDC_SET_ETHERNET_MULTICAST_FILTERS: + * case USB_CDC_SET_ETHERNET_PM_PATTERN_FILTER: + * case USB_CDC_GET_ETHERNET_PM_PATTERN_FILTER: + * case USB_CDC_GET_ETHERNET_STATISTIC: + */ + + case ((USB_DIR_IN | USB_TYPE_CLASS | USB_RECIP_INTERFACE) << 8) + | USB_CDC_GET_NTB_PARAMETERS: + + if (w_length == 0 || w_value != 0 || w_index != ncm->ctrl_id) + goto invalid; + value = w_length > sizeof ntb_parameters ? + sizeof ntb_parameters : w_length; + memcpy(req->buf, &ntb_parameters, value); + VDBG(cdev, "Host asked NTB parameters\n"); + break; + + case ((USB_DIR_IN | USB_TYPE_CLASS | USB_RECIP_INTERFACE) << 8) + | USB_CDC_GET_NTB_INPUT_SIZE: + + if (w_length < 4 || w_value != 0 || w_index != ncm->ctrl_id) + goto invalid; + put_unaligned_le32(ncm->port.fixed_in_len, req->buf); + value = 4; + VDBG(cdev, "Host asked INPUT SIZE, sending %d\n", + ncm->port.fixed_in_len); + break; + + case ((USB_DIR_OUT | USB_TYPE_CLASS | USB_RECIP_INTERFACE) << 8) + | USB_CDC_SET_NTB_INPUT_SIZE: + { + if (w_length != 4 || w_value != 0 || w_index != ncm->ctrl_id) + goto invalid; + req->complete = ncm_ep0out_complete; + req->length = w_length; + req->context = f; + + value = req->length; + break; + } + + case ((USB_DIR_IN | USB_TYPE_CLASS | USB_RECIP_INTERFACE) << 8) + | USB_CDC_GET_NTB_FORMAT: + { + uint16_t format; + + if (w_length < 2 || w_value != 0 || w_index != ncm->ctrl_id) + goto invalid; + format = (ncm->parser_opts == &ndp16_opts) ? 0x0000 : 0x0001; + put_unaligned_le16(format, req->buf); + value = 2; + VDBG(cdev, "Host asked NTB FORMAT, sending %d\n", format); + break; + } + + case ((USB_DIR_OUT | USB_TYPE_CLASS | USB_RECIP_INTERFACE) << 8) + | USB_CDC_SET_NTB_FORMAT: + { + if (w_length != 0 || w_index != ncm->ctrl_id) + goto invalid; + switch (w_value) { + case 0x0000: + ncm->parser_opts = &ndp16_opts; + DBG(cdev, "NCM16 selected\n"); + break; + case 0x0001: + ncm->parser_opts = &ndp32_opts; + DBG(cdev, "NCM32 selected\n"); + break; + default: + goto invalid; + } + value = 0; + break; + } + case ((USB_DIR_IN | USB_TYPE_CLASS | USB_RECIP_INTERFACE) << 8) + | USB_CDC_GET_CRC_MODE: + { + uint16_t is_crc; + + if (w_length < 2 || w_value != 0 || w_index != ncm->ctrl_id) + goto invalid; + is_crc = ncm->is_crc ? 0x0001 : 0x0000; + put_unaligned_le16(is_crc, req->buf); + value = 2; + VDBG(cdev, "Host asked CRC MODE, sending %d\n", is_crc); + break; + } + + case ((USB_DIR_OUT | USB_TYPE_CLASS | USB_RECIP_INTERFACE) << 8) + | USB_CDC_SET_CRC_MODE: + { + int ndp_hdr_crc = 0; + + if (w_length != 0 || w_index != ncm->ctrl_id) + goto invalid; + switch (w_value) { + case 0x0000: + ncm->is_crc = false; + ndp_hdr_crc = NCM_NDP_HDR_NOCRC; + DBG(cdev, "non-CRC mode selected\n"); + break; + case 0x0001: + ncm->is_crc = true; + ndp_hdr_crc = NCM_NDP_HDR_CRC; + DBG(cdev, "CRC mode selected\n"); + break; + default: + goto invalid; + } + ncm->parser_opts->ndp_sign &= ~NCM_NDP_HDR_CRC_MASK; + ncm->parser_opts->ndp_sign |= ndp_hdr_crc; + value = 0; + break; + } + + /* and disabled in ncm descriptor: */ + /* case USB_CDC_GET_NET_ADDRESS: */ + /* case USB_CDC_SET_NET_ADDRESS: */ + /* case USB_CDC_GET_MAX_DATAGRAM_SIZE: */ + /* case USB_CDC_SET_MAX_DATAGRAM_SIZE: */ + + default: +invalid: + DBG(cdev, "invalid control req%02x.%02x v%04x i%04x l%d\n", + ctrl->bRequestType, ctrl->bRequest, + w_value, w_index, w_length); + } + + /* respond with data transfer or status phase? */ + if (value >= 0) { + DBG(cdev, "ncm req%02x.%02x v%04x i%04x l%d\n", + ctrl->bRequestType, ctrl->bRequest, + w_value, w_index, w_length); + req->zero = 0; + req->length = value; + value = usb_ep_queue(cdev->gadget->ep0, req, GFP_ATOMIC); + if (value < 0) + ERROR(cdev, "ncm req %02x.%02x response err %d\n", + ctrl->bRequestType, ctrl->bRequest, + value); + } + + /* device either stalls (value < 0) or reports success */ + return value; +} + + +static int ncm_set_alt(struct usb_function *f, unsigned intf, unsigned alt) +{ + struct f_ncm *ncm = func_to_ncm(f); + struct usb_composite_dev *cdev = f->config->cdev; + + /* Control interface has only altsetting 0 */ + if (intf == ncm->ctrl_id) { + if (alt != 0) + goto fail; + + if (ncm->notify->driver_data) { + DBG(cdev, "reset ncm control %d\n", intf); + usb_ep_disable(ncm->notify); + } else { + DBG(cdev, "init ncm ctrl %d\n", intf); + ncm->notify_desc = ep_choose(cdev->gadget, + ncm->hs.notify, + ncm->fs.notify); + } + usb_ep_enable(ncm->notify, ncm->notify_desc); + ncm->notify->driver_data = ncm; + + /* Data interface has two altsettings, 0 and 1 */ + } else if (intf == ncm->data_id) { + if (alt > 1) + goto fail; + + if (ncm->port.in_ep->driver_data) { + DBG(cdev, "reset ncm\n"); + gether_disconnect(&ncm->port); + ncm_reset_values(ncm); + } + + /* + * CDC Network only sends data in non-default altsettings. + * Changing altsettings resets filters, statistics, etc. + */ + if (alt == 1) { + struct net_device *net; + + if (!ncm->port.in) { + DBG(cdev, "init ncm\n"); + ncm->port.in = ep_choose(cdev->gadget, + ncm->hs.in, + ncm->fs.in); + ncm->port.out = ep_choose(cdev->gadget, + ncm->hs.out, + ncm->fs.out); + } + + /* TODO */ + /* Enable zlps by default for NCM conformance; + * override for musb_hdrc (avoids txdma ovhead) + */ + ncm->port.is_zlp_ok = !( + gadget_is_musbhdrc(cdev->gadget) + ); + ncm->port.cdc_filter = DEFAULT_FILTER; + DBG(cdev, "activate ncm\n"); + net = gether_connect(&ncm->port); + if (IS_ERR(net)) + return PTR_ERR(net); + } + + spin_lock(&ncm->lock); + ncm_notify(ncm); + spin_unlock(&ncm->lock); + } else + goto fail; + + return 0; +fail: + return -EINVAL; +} + +/* + * Because the data interface supports multiple altsettings, + * this NCM function *MUST* implement a get_alt() method. + */ +static int ncm_get_alt(struct usb_function *f, unsigned intf) +{ + struct f_ncm *ncm = func_to_ncm(f); + + if (intf == ncm->ctrl_id) + return 0; + return ncm->port.in_ep->driver_data ? 1 : 0; +} + +static struct sk_buff *ncm_wrap_ntb(struct gether *port, + struct sk_buff *skb) +{ + struct f_ncm *ncm = func_to_ncm(&port->func); + struct sk_buff *skb2; + int ncb_len = 0; + __le16 *tmp; + int div = ntb_parameters.wNdpInDivisor; + int rem = ntb_parameters.wNdpInPayloadRemainder; + int pad; + int ndp_align = ntb_parameters.wNdpInAlignment; + int ndp_pad; + unsigned max_size = ncm->port.fixed_in_len; + struct ndp_parser_opts *opts = ncm->parser_opts; + unsigned crc_len = ncm->is_crc ? sizeof(uint32_t) : 0; + + ncb_len += opts->nth_size; + ndp_pad = ALIGN(ncb_len, ndp_align) - ncb_len; + ncb_len += ndp_pad; + ncb_len += opts->ndp_size; + ncb_len += 2 * 2 * opts->dgram_item_len; /* Datagram entry */ + ncb_len += 2 * 2 * opts->dgram_item_len; /* Zero datagram entry */ + pad = ALIGN(ncb_len, div) + rem - ncb_len; + ncb_len += pad; + + if (ncb_len + skb->len + crc_len > max_size) { + dev_kfree_skb_any(skb); + return NULL; + } + + skb2 = skb_copy_expand(skb, ncb_len, + max_size - skb->len - ncb_len - crc_len, + GFP_ATOMIC); + dev_kfree_skb_any(skb); + if (!skb2) + return NULL; + + skb = skb2; + + tmp = (void *) skb_push(skb, ncb_len); + memset(tmp, 0, ncb_len); + + put_unaligned_le32(opts->nth_sign, tmp); /* dwSignature */ + tmp += 2; + /* wHeaderLength */ + put_unaligned_le16(opts->nth_size, tmp++); + tmp++; /* skip wSequence */ + put_ncm(&tmp, opts->block_length, skb->len); /* (d)wBlockLength */ + /* (d)wFpIndex */ + /* the first pointer is right after the NTH + align */ + put_ncm(&tmp, opts->fp_index, opts->nth_size + ndp_pad); + + tmp = (void *)tmp + ndp_pad; + + /* NDP */ + put_unaligned_le32(opts->ndp_sign, tmp); /* dwSignature */ + tmp += 2; + /* wLength */ + put_unaligned_le16(ncb_len - opts->nth_size - pad, tmp++); + + tmp += opts->reserved1; + tmp += opts->next_fp_index; /* skip reserved (d)wNextFpIndex */ + tmp += opts->reserved2; + + if (ncm->is_crc) { + uint32_t crc; + + crc = ~crc32_le(~0, + skb->data + ncb_len, + skb->len - ncb_len); + put_unaligned_le32(crc, skb->data + skb->len); + skb_put(skb, crc_len); + } + + /* (d)wDatagramIndex[0] */ + put_ncm(&tmp, opts->dgram_item_len, ncb_len); + /* (d)wDatagramLength[0] */ + put_ncm(&tmp, opts->dgram_item_len, skb->len - ncb_len); + /* (d)wDatagramIndex[1] and (d)wDatagramLength[1] already zeroed */ + + if (skb->len > MAX_TX_NONFIXED) + memset(skb_put(skb, max_size - skb->len), + 0, max_size - skb->len); + + return skb; +} + +static int ncm_unwrap_ntb(struct gether *port, + struct sk_buff *skb, + struct sk_buff_head *list) +{ + struct f_ncm *ncm = func_to_ncm(&port->func); + __le16 *tmp = (void *) skb->data; + unsigned index, index2; + unsigned dg_len, dg_len2; + unsigned ndp_len; + struct sk_buff *skb2; + int ret = -EINVAL; + unsigned max_size = le32_to_cpu(ntb_parameters.dwNtbOutMaxSize); + struct ndp_parser_opts *opts = ncm->parser_opts; + unsigned crc_len = ncm->is_crc ? sizeof(uint32_t) : 0; + int dgram_counter; + + /* dwSignature */ + if (get_unaligned_le32(tmp) != opts->nth_sign) { + INFO(port->func.config->cdev, "Wrong NTH SIGN, skblen %d\n", + skb->len); + print_hex_dump(KERN_INFO, "HEAD:", DUMP_PREFIX_ADDRESS, 32, 1, + skb->data, 32, false); + + goto err; + } + tmp += 2; + /* wHeaderLength */ + if (get_unaligned_le16(tmp++) != opts->nth_size) { + INFO(port->func.config->cdev, "Wrong NTB headersize\n"); + goto err; + } + tmp++; /* skip wSequence */ + + /* (d)wBlockLength */ + if (get_ncm(&tmp, opts->block_length) > max_size) { + INFO(port->func.config->cdev, "OUT size exceeded\n"); + goto err; + } + + index = get_ncm(&tmp, opts->fp_index); + /* NCM 3.2 */ + if (((index % 4) != 0) && (index < opts->nth_size)) { + INFO(port->func.config->cdev, "Bad index: %x\n", + index); + goto err; + } + + /* walk through NDP */ + tmp = ((void *)skb->data) + index; + if (get_unaligned_le32(tmp) != opts->ndp_sign) { + INFO(port->func.config->cdev, "Wrong NDP SIGN\n"); + goto err; + } + tmp += 2; + + ndp_len = get_unaligned_le16(tmp++); + /* + * NCM 3.3.1 + * entry is 2 items + * item size is 16/32 bits, opts->dgram_item_len * 2 bytes + * minimal: struct usb_cdc_ncm_ndpX + normal entry + zero entry + */ + if ((ndp_len < opts->ndp_size + 2 * 2 * (opts->dgram_item_len * 2)) + || (ndp_len % opts->ndplen_align != 0)) { + INFO(port->func.config->cdev, "Bad NDP length: %x\n", ndp_len); + goto err; + } + tmp += opts->reserved1; + tmp += opts->next_fp_index; /* skip reserved (d)wNextFpIndex */ + tmp += opts->reserved2; + + ndp_len -= opts->ndp_size; + index2 = get_ncm(&tmp, opts->dgram_item_len); + dg_len2 = get_ncm(&tmp, opts->dgram_item_len); + dgram_counter = 0; + + do { + index = index2; + dg_len = dg_len2; + if (dg_len < 14 + crc_len) { /* ethernet header + crc */ + INFO(port->func.config->cdev, "Bad dgram length: %x\n", + dg_len); + goto err; + } + if (ncm->is_crc) { + uint32_t crc, crc2; + + crc = get_unaligned_le32(skb->data + + index + dg_len - crc_len); + crc2 = ~crc32_le(~0, + skb->data + index, + dg_len - crc_len); + if (crc != crc2) { + INFO(port->func.config->cdev, "Bad CRC\n"); + goto err; + } + } + + index2 = get_ncm(&tmp, opts->dgram_item_len); + dg_len2 = get_ncm(&tmp, opts->dgram_item_len); + + if (index2 == 0 || dg_len2 == 0) { + skb2 = skb; + } else { + skb2 = skb_clone(skb, GFP_ATOMIC); + if (skb2 == NULL) + goto err; + } + + if (!skb_pull(skb2, index)) { + ret = -EOVERFLOW; + goto err; + } + + skb_trim(skb2, dg_len - crc_len); + skb_queue_tail(list, skb2); + + ndp_len -= 2 * (opts->dgram_item_len * 2); + + dgram_counter++; + + if (index2 == 0 || dg_len2 == 0) + break; + } while (ndp_len > 2 * (opts->dgram_item_len * 2)); /* zero entry */ + + VDBG(port->func.config->cdev, + "Parsed NTB with %d frames\n", dgram_counter); + return 0; +err: + skb_queue_purge(list); + dev_kfree_skb_any(skb); + return ret; +} + +static void ncm_disable(struct usb_function *f) +{ + struct f_ncm *ncm = func_to_ncm(f); + struct usb_composite_dev *cdev = f->config->cdev; + + DBG(cdev, "ncm deactivated\n"); + + if (ncm->port.in_ep->driver_data) + gether_disconnect(&ncm->port); + + if (ncm->notify->driver_data) { + usb_ep_disable(ncm->notify); + ncm->notify->driver_data = NULL; + ncm->notify_desc = NULL; + } +} + +/*-------------------------------------------------------------------------*/ + +/* + * Callbacks let us notify the host about connect/disconnect when the + * net device is opened or closed. + * + * For testing, note that link states on this side include both opened + * and closed variants of: + * + * - disconnected/unconfigured + * - configured but inactive (data alt 0) + * - configured and active (data alt 1) + * + * Each needs to be tested with unplug, rmmod, SET_CONFIGURATION, and + * SET_INTERFACE (altsetting). Remember also that "configured" doesn't + * imply the host is actually polling the notification endpoint, and + * likewise that "active" doesn't imply it's actually using the data + * endpoints for traffic. + */ + +static void ncm_open(struct gether *geth) +{ + struct f_ncm *ncm = func_to_ncm(&geth->func); + + DBG(ncm->port.func.config->cdev, "%s\n", __func__); + + spin_lock(&ncm->lock); + ncm->is_open = true; + ncm_notify(ncm); + spin_unlock(&ncm->lock); +} + +static void ncm_close(struct gether *geth) +{ + struct f_ncm *ncm = func_to_ncm(&geth->func); + + DBG(ncm->port.func.config->cdev, "%s\n", __func__); + + spin_lock(&ncm->lock); + ncm->is_open = false; + ncm_notify(ncm); + spin_unlock(&ncm->lock); +} + +/*-------------------------------------------------------------------------*/ + +/* ethernet function driver setup/binding */ + +static int __init +ncm_bind(struct usb_configuration *c, struct usb_function *f) +{ + struct usb_composite_dev *cdev = c->cdev; + struct f_ncm *ncm = func_to_ncm(f); + int status; + struct usb_ep *ep; + + /* allocate instance-specific interface IDs */ + status = usb_interface_id(c, f); + if (status < 0) + goto fail; + ncm->ctrl_id = status; + ncm_iad_desc.bFirstInterface = status; + + ncm_control_intf.bInterfaceNumber = status; + ncm_union_desc.bMasterInterface0 = status; + + status = usb_interface_id(c, f); + if (status < 0) + goto fail; + ncm->data_id = status; + + ncm_data_nop_intf.bInterfaceNumber = status; + ncm_data_intf.bInterfaceNumber = status; + ncm_union_desc.bSlaveInterface0 = status; + + status = -ENODEV; + + /* allocate instance-specific endpoints */ + ep = usb_ep_autoconfig(cdev->gadget, &fs_ncm_in_desc); + if (!ep) + goto fail; + ncm->port.in_ep = ep; + ep->driver_data = cdev; /* claim */ + + ep = usb_ep_autoconfig(cdev->gadget, &fs_ncm_out_desc); + if (!ep) + goto fail; + ncm->port.out_ep = ep; + ep->driver_data = cdev; /* claim */ + + ep = usb_ep_autoconfig(cdev->gadget, &fs_ncm_notify_desc); + if (!ep) + goto fail; + ncm->notify = ep; + ep->driver_data = cdev; /* claim */ + + status = -ENOMEM; + + /* allocate notification request and buffer */ + ncm->notify_req = usb_ep_alloc_request(ep, GFP_KERNEL); + if (!ncm->notify_req) + goto fail; + ncm->notify_req->buf = kmalloc(NCM_STATUS_BYTECOUNT, GFP_KERNEL); + if (!ncm->notify_req->buf) + goto fail; + ncm->notify_req->context = ncm; + ncm->notify_req->complete = ncm_notify_complete; + + /* copy descriptors, and track endpoint copies */ + f->descriptors = usb_copy_descriptors(ncm_fs_function); + if (!f->descriptors) + goto fail; + + ncm->fs.in = usb_find_endpoint(ncm_fs_function, + f->descriptors, &fs_ncm_in_desc); + ncm->fs.out = usb_find_endpoint(ncm_fs_function, + f->descriptors, &fs_ncm_out_desc); + ncm->fs.notify = usb_find_endpoint(ncm_fs_function, + f->descriptors, &fs_ncm_notify_desc); + + /* + * support all relevant hardware speeds... we expect that when + * hardware is dual speed, all bulk-capable endpoints work at + * both speeds + */ + if (gadget_is_dualspeed(c->cdev->gadget)) { + hs_ncm_in_desc.bEndpointAddress = + fs_ncm_in_desc.bEndpointAddress; + hs_ncm_out_desc.bEndpointAddress = + fs_ncm_out_desc.bEndpointAddress; + hs_ncm_notify_desc.bEndpointAddress = + fs_ncm_notify_desc.bEndpointAddress; + + /* copy descriptors, and track endpoint copies */ + f->hs_descriptors = usb_copy_descriptors(ncm_hs_function); + if (!f->hs_descriptors) + goto fail; + + ncm->hs.in = usb_find_endpoint(ncm_hs_function, + f->hs_descriptors, &hs_ncm_in_desc); + ncm->hs.out = usb_find_endpoint(ncm_hs_function, + f->hs_descriptors, &hs_ncm_out_desc); + ncm->hs.notify = usb_find_endpoint(ncm_hs_function, + f->hs_descriptors, &hs_ncm_notify_desc); + } + + /* + * NOTE: all that is done without knowing or caring about + * the network link ... which is unavailable to this code + * until we're activated via set_alt(). + */ + + ncm->port.open = ncm_open; + ncm->port.close = ncm_close; + + DBG(cdev, "CDC Network: %s speed IN/%s OUT/%s NOTIFY/%s\n", + gadget_is_dualspeed(c->cdev->gadget) ? "dual" : "full", + ncm->port.in_ep->name, ncm->port.out_ep->name, + ncm->notify->name); + return 0; + +fail: + if (f->descriptors) + usb_free_descriptors(f->descriptors); + + if (ncm->notify_req) { + kfree(ncm->notify_req->buf); + usb_ep_free_request(ncm->notify, ncm->notify_req); + } + + /* we might as well release our claims on endpoints */ + if (ncm->notify) + ncm->notify->driver_data = NULL; + if (ncm->port.out) + ncm->port.out_ep->driver_data = NULL; + if (ncm->port.in) + ncm->port.in_ep->driver_data = NULL; + + ERROR(cdev, "%s: can't bind, err %d\n", f->name, status); + + return status; +} + +static void +ncm_unbind(struct usb_configuration *c, struct usb_function *f) +{ + struct f_ncm *ncm = func_to_ncm(f); + + DBG(c->cdev, "ncm unbind\n"); + + if (gadget_is_dualspeed(c->cdev->gadget)) + usb_free_descriptors(f->hs_descriptors); + usb_free_descriptors(f->descriptors); + + kfree(ncm->notify_req->buf); + usb_ep_free_request(ncm->notify, ncm->notify_req); + + ncm_string_defs[1].s = NULL; + kfree(ncm); +} + +/** + * ncm_bind_config - add CDC Network link to a configuration + * @c: the configuration to support the network link + * @ethaddr: a buffer in which the ethernet address of the host side + * side of the link was recorded + * Context: single threaded during gadget setup + * + * Returns zero on success, else negative errno. + * + * Caller must have called @gether_setup(). Caller is also responsible + * for calling @gether_cleanup() before module unload. + */ +int __init ncm_bind_config(struct usb_configuration *c, u8 ethaddr[ETH_ALEN]) +{ + struct f_ncm *ncm; + int status; + + if (!can_support_ecm(c->cdev->gadget) || !ethaddr) + return -EINVAL; + + /* maybe allocate device-global string IDs */ + if (ncm_string_defs[0].id == 0) { + + /* control interface label */ + status = usb_string_id(c->cdev); + if (status < 0) + return status; + ncm_string_defs[STRING_CTRL_IDX].id = status; + ncm_control_intf.iInterface = status; + + /* data interface label */ + status = usb_string_id(c->cdev); + if (status < 0) + return status; + ncm_string_defs[STRING_DATA_IDX].id = status; + ncm_data_nop_intf.iInterface = status; + ncm_data_intf.iInterface = status; + + /* MAC address */ + status = usb_string_id(c->cdev); + if (status < 0) + return status; + ncm_string_defs[STRING_MAC_IDX].id = status; + ecm_desc.iMACAddress = status; + + /* IAD */ + status = usb_string_id(c->cdev); + if (status < 0) + return status; + ncm_string_defs[STRING_IAD_IDX].id = status; + ncm_iad_desc.iFunction = status; + } + + /* allocate and initialize one new instance */ + ncm = kzalloc(sizeof *ncm, GFP_KERNEL); + if (!ncm) + return -ENOMEM; + + /* export host's Ethernet address in CDC format */ + snprintf(ncm->ethaddr, sizeof ncm->ethaddr, + "%02X%02X%02X%02X%02X%02X", + ethaddr[0], ethaddr[1], ethaddr[2], + ethaddr[3], ethaddr[4], ethaddr[5]); + ncm_string_defs[1].s = ncm->ethaddr; + + spin_lock_init(&ncm->lock); + ncm_reset_values(ncm); + ncm->port.is_fixed = true; + + ncm->port.func.name = "cdc_network"; + ncm->port.func.strings = ncm_strings; + /* descriptors are per-instance copies */ + ncm->port.func.bind = ncm_bind; + ncm->port.func.unbind = ncm_unbind; + ncm->port.func.set_alt = ncm_set_alt; + ncm->port.func.get_alt = ncm_get_alt; + ncm->port.func.setup = ncm_setup; + ncm->port.func.disable = ncm_disable; + + ncm->port.wrap = ncm_wrap_ntb; + ncm->port.unwrap = ncm_unwrap_ntb; + + status = usb_add_function(c, &ncm->port.func); + if (status) { + ncm_string_defs[1].s = NULL; + kfree(ncm); + } + return status; +} diff --git a/drivers/usb/gadget/file_storage.c b/drivers/usb/gadget/file_storage.c index d4fdf65fb925..a6eacb59571b 100644 --- a/drivers/usb/gadget/file_storage.c +++ b/drivers/usb/gadget/file_storage.c @@ -3392,25 +3392,28 @@ static int __init fsg_bind(struct usb_gadget *gadget) dev_set_name(&curlun->dev,"%s-lun%d", dev_name(&gadget->dev), i); - if ((rc = device_register(&curlun->dev)) != 0) { + kref_get(&fsg->ref); + rc = device_register(&curlun->dev); + if (rc) { INFO(fsg, "failed to register LUN%d: %d\n", i, rc); - goto out; - } - if ((rc = device_create_file(&curlun->dev, - &dev_attr_ro)) != 0 || - (rc = device_create_file(&curlun->dev, - &dev_attr_nofua)) != 0 || - (rc = device_create_file(&curlun->dev, - &dev_attr_file)) != 0) { - device_unregister(&curlun->dev); + put_device(&curlun->dev); goto out; } curlun->registered = 1; - kref_get(&fsg->ref); + + rc = device_create_file(&curlun->dev, &dev_attr_ro); + if (rc) + goto out; + rc = device_create_file(&curlun->dev, &dev_attr_nofua); + if (rc) + goto out; + rc = device_create_file(&curlun->dev, &dev_attr_file); + if (rc) + goto out; if (mod_data.file[i] && *mod_data.file[i]) { - if ((rc = fsg_lun_open(curlun, - mod_data.file[i])) != 0) + rc = fsg_lun_open(curlun, mod_data.file[i]); + if (rc) goto out; } else if (!mod_data.removable) { ERROR(fsg, "no file given for LUN%d\n", i); diff --git a/drivers/usb/gadget/g_ffs.c b/drivers/usb/gadget/g_ffs.c index af75e3620849..ebf6970a10bf 100644 --- a/drivers/usb/gadget/g_ffs.c +++ b/drivers/usb/gadget/g_ffs.c @@ -1,7 +1,29 @@ +/* + * g_ffs.c -- user mode file system API for USB composite function controllers + * + * Copyright (C) 2010 Samsung Electronics + * Author: Michal Nazarewicz <m.nazarewicz@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#define pr_fmt(fmt) "g_ffs: " fmt + #include <linux/module.h> #include <linux/utsname.h> - /* * kbuild is not very cooperative with respect to linking separately * compiled library objects into one module. So for now we won't use @@ -43,7 +65,6 @@ static int eth_bind_config(struct usb_configuration *c, u8 ethaddr[ETH_ALEN]); #include "f_fs.c" - #define DRIVER_NAME "g_ffs" #define DRIVER_DESC "USB Function Filesystem" #define DRIVER_VERSION "24 Aug 2004" @@ -73,8 +94,6 @@ MODULE_PARM_DESC(bDeviceSubClass, "USB Device subclass"); module_param_named(bDeviceProtocol, gfs_dev_desc.bDeviceProtocol, byte, 0644); MODULE_PARM_DESC(bDeviceProtocol, "USB Device protocol"); - - static const struct usb_descriptor_header *gfs_otg_desc[] = { (const struct usb_descriptor_header *) &(const struct usb_otg_descriptor) { @@ -91,8 +110,7 @@ static const struct usb_descriptor_header *gfs_otg_desc[] = { NULL }; -/* string IDs are assigned dynamically */ - +/* String IDs are assigned dynamically */ static struct usb_string gfs_strings[] = { #ifdef CONFIG_USB_FUNCTIONFS_RNDIS { .s = "FunctionFS + RNDIS" }, @@ -114,8 +132,6 @@ static struct usb_gadget_strings *gfs_dev_strings[] = { NULL, }; - - struct gfs_configuration { struct usb_configuration c; int (*eth)(struct usb_configuration *c, u8 *ethaddr); @@ -138,7 +154,6 @@ struct gfs_configuration { #endif }; - static int gfs_bind(struct usb_composite_dev *cdev); static int gfs_unbind(struct usb_composite_dev *cdev); static int gfs_do_config(struct usb_configuration *c); @@ -151,11 +166,9 @@ static struct usb_composite_driver gfs_driver = { .iProduct = DRIVER_DESC, }; - static struct ffs_data *gfs_ffs_data; static unsigned long gfs_registered; - static int gfs_init(void) { ENTER(); @@ -175,7 +188,6 @@ static void gfs_exit(void) } module_exit(gfs_exit); - static int functionfs_ready_callback(struct ffs_data *ffs) { int ret; @@ -200,14 +212,11 @@ static void functionfs_closed_callback(struct ffs_data *ffs) usb_composite_unregister(&gfs_driver); } - static int functionfs_check_dev_callback(const char *dev_name) { return 0; } - - static int gfs_bind(struct usb_composite_dev *cdev) { int ret, i; @@ -274,7 +283,6 @@ static int gfs_unbind(struct usb_composite_dev *cdev) return 0; } - static int gfs_do_config(struct usb_configuration *c) { struct gfs_configuration *gc = @@ -315,7 +323,6 @@ static int gfs_do_config(struct usb_configuration *c) return 0; } - #ifdef CONFIG_USB_FUNCTIONFS_ETH static int eth_bind_config(struct usb_configuration *c, u8 ethaddr[ETH_ALEN]) diff --git a/drivers/usb/gadget/gadget_chips.h b/drivers/usb/gadget/gadget_chips.h index e511fec9f26d..5c2720d64ffa 100644 --- a/drivers/usb/gadget/gadget_chips.h +++ b/drivers/usb/gadget/gadget_chips.h @@ -96,7 +96,7 @@ /* Mentor high speed "dual role" controller, in peripheral role */ #ifdef CONFIG_USB_GADGET_MUSB_HDRC -#define gadget_is_musbhdrc(g) !strcmp("musb_hdrc", (g)->name) +#define gadget_is_musbhdrc(g) !strcmp("musb-hdrc", (g)->name) #else #define gadget_is_musbhdrc(g) 0 #endif @@ -120,10 +120,10 @@ #define gadget_is_fsl_qe(g) 0 #endif -#ifdef CONFIG_USB_GADGET_CI13XXX -#define gadget_is_ci13xxx(g) (!strcmp("ci13xxx_udc", (g)->name)) +#ifdef CONFIG_USB_GADGET_CI13XXX_PCI +#define gadget_is_ci13xxx_pci(g) (!strcmp("ci13xxx_pci", (g)->name)) #else -#define gadget_is_ci13xxx(g) 0 +#define gadget_is_ci13xxx_pci(g) 0 #endif // CONFIG_USB_GADGET_SX2 @@ -142,6 +142,17 @@ #define gadget_is_s3c_hsotg(g) 0 #endif +#ifdef CONFIG_USB_GADGET_EG20T +#define gadget_is_pch(g) (!strcmp("pch_udc", (g)->name)) +#else +#define gadget_is_pch(g) 0 +#endif + +#ifdef CONFIG_USB_GADGET_CI13XXX_MSM +#define gadget_is_ci13xxx_msm(g) (!strcmp("ci13xxx_msm", (g)->name)) +#else +#define gadget_is_ci13xxx_msm(g) 0 +#endif /** * usb_gadget_controller_number - support bcdDevice id convention @@ -192,7 +203,7 @@ static inline int usb_gadget_controller_number(struct usb_gadget *gadget) return 0x21; else if (gadget_is_fsl_qe(gadget)) return 0x22; - else if (gadget_is_ci13xxx(gadget)) + else if (gadget_is_ci13xxx_pci(gadget)) return 0x23; else if (gadget_is_langwell(gadget)) return 0x24; @@ -200,6 +211,10 @@ static inline int usb_gadget_controller_number(struct usb_gadget *gadget) return 0x25; else if (gadget_is_s3c_hsotg(gadget)) return 0x26; + else if (gadget_is_pch(gadget)) + return 0x27; + else if (gadget_is_ci13xxx_msm(gadget)) + return 0x28; return -ENOENT; } diff --git a/drivers/usb/gadget/imx_udc.c b/drivers/usb/gadget/imx_udc.c index ed0266462c57..1210534822d6 100644 --- a/drivers/usb/gadget/imx_udc.c +++ b/drivers/usb/gadget/imx_udc.c @@ -1191,13 +1191,17 @@ static irqreturn_t imx_udc_ctrl_irq(int irq, void *dev) return IRQ_HANDLED; } +#ifndef MX1_INT_USBD0 +#define MX1_INT_USBD0 MX1_USBD_INT0 +#endif + static irqreturn_t imx_udc_bulk_irq(int irq, void *dev) { struct imx_udc_struct *imx_usb = dev; - struct imx_ep_struct *imx_ep = &imx_usb->imx_ep[irq - USBD_INT0]; + struct imx_ep_struct *imx_ep = &imx_usb->imx_ep[irq - MX1_INT_USBD0]; int intr = __raw_readl(imx_usb->base + USB_EP_INTR(EP_NO(imx_ep))); - dump_ep_intr(__func__, irq - USBD_INT0, intr, imx_usb->dev); + dump_ep_intr(__func__, irq - MX1_INT_USBD0, intr, imx_usb->dev); if (!imx_usb->driver) { __raw_writel(intr, imx_usb->base + USB_EP_INTR(EP_NO(imx_ep))); diff --git a/drivers/usb/gadget/imx_udc.h b/drivers/usb/gadget/imx_udc.h index b48ad59603d1..7136c242b4ec 100644 --- a/drivers/usb/gadget/imx_udc.h +++ b/drivers/usb/gadget/imx_udc.h @@ -23,9 +23,6 @@ /* Helper macros */ #define EP_NO(ep) ((ep->bEndpointAddress) & ~USB_DIR_IN) /* IN:1, OUT:0 */ #define EP_DIR(ep) ((ep->bEndpointAddress) & USB_DIR_IN ? 1 : 0) -#define irq_to_ep(irq) (((irq) >= USBD_INT0) || ((irq) <= USBD_INT6) \ - ? ((irq) - USBD_INT0) : (USBD_INT6)) /*should not happen*/ -#define ep_to_irq(ep) (EP_NO((ep)) + USBD_INT0) #define IMX_USB_NB_EP 6 /* Driver structures */ diff --git a/drivers/usb/gadget/langwell_udc.c b/drivers/usb/gadget/langwell_udc.c index b8ec954c0692..777972454e3e 100644 --- a/drivers/usb/gadget/langwell_udc.c +++ b/drivers/usb/gadget/langwell_udc.c @@ -2225,6 +2225,7 @@ static void handle_setup_packet(struct langwell_udc *dev, u16 wValue = le16_to_cpu(setup->wValue); u16 wIndex = le16_to_cpu(setup->wIndex); u16 wLength = le16_to_cpu(setup->wLength); + u32 portsc1; dev_vdbg(&dev->pdev->dev, "---> %s()\n", __func__); @@ -2313,6 +2314,28 @@ static void handle_setup_packet(struct langwell_udc *dev, dev->dev_status &= ~(1 << wValue); } break; + case USB_DEVICE_TEST_MODE: + dev_dbg(&dev->pdev->dev, "SETUP: TEST MODE\n"); + if ((wIndex & 0xff) || + (dev->gadget.speed != USB_SPEED_HIGH)) + ep0_stall(dev); + + switch (wIndex >> 8) { + case TEST_J: + case TEST_K: + case TEST_SE0_NAK: + case TEST_PACKET: + case TEST_FORCE_EN: + if (prime_status_phase(dev, EP_DIR_IN)) + ep0_stall(dev); + portsc1 = readl(&dev->op_regs->portsc1); + portsc1 |= (wIndex & 0xf00) << 8; + writel(portsc1, &dev->op_regs->portsc1); + goto end; + default: + rc = -EOPNOTSUPP; + } + break; default: rc = -EOPNOTSUPP; break; diff --git a/drivers/usb/gadget/mass_storage.c b/drivers/usb/gadget/mass_storage.c index 0769179dbdb0..01822422c3e8 100644 --- a/drivers/usb/gadget/mass_storage.c +++ b/drivers/usb/gadget/mass_storage.c @@ -102,7 +102,7 @@ static struct fsg_module_parameters mod_data = { }; FSG_MODULE_PARAMETERS(/* no prefix */, mod_data); -static unsigned long msg_registered = 0; +static unsigned long msg_registered; static void msg_cleanup(void); static int msg_thread_exits(struct fsg_common *common) diff --git a/drivers/usb/gadget/mv_udc.h b/drivers/usb/gadget/mv_udc.h new file mode 100644 index 000000000000..65f1f7c3bd4e --- /dev/null +++ b/drivers/usb/gadget/mv_udc.h @@ -0,0 +1,294 @@ + +#ifndef __MV_UDC_H +#define __MV_UDC_H + +#define VUSBHS_MAX_PORTS 8 + +#define DQH_ALIGNMENT 2048 +#define DTD_ALIGNMENT 64 +#define DMA_BOUNDARY 4096 + +#define EP_DIR_IN 1 +#define EP_DIR_OUT 0 + +#define DMA_ADDR_INVALID (~(dma_addr_t)0) + +#define EP0_MAX_PKT_SIZE 64 +/* ep0 transfer state */ +#define WAIT_FOR_SETUP 0 +#define DATA_STATE_XMIT 1 +#define DATA_STATE_NEED_ZLP 2 +#define WAIT_FOR_OUT_STATUS 3 +#define DATA_STATE_RECV 4 + +#define CAPLENGTH_MASK (0xff) +#define DCCPARAMS_DEN_MASK (0x1f) + +#define HCSPARAMS_PPC (0x10) + +/* Frame Index Register Bit Masks */ +#define USB_FRINDEX_MASKS 0x3fff + +/* Command Register Bit Masks */ +#define USBCMD_RUN_STOP (0x00000001) +#define USBCMD_CTRL_RESET (0x00000002) +#define USBCMD_SETUP_TRIPWIRE_SET (0x00002000) +#define USBCMD_SETUP_TRIPWIRE_CLEAR (~USBCMD_SETUP_TRIPWIRE_SET) + +#define USBCMD_ATDTW_TRIPWIRE_SET (0x00004000) +#define USBCMD_ATDTW_TRIPWIRE_CLEAR (~USBCMD_ATDTW_TRIPWIRE_SET) + +/* bit 15,3,2 are for frame list size */ +#define USBCMD_FRAME_SIZE_1024 (0x00000000) /* 000 */ +#define USBCMD_FRAME_SIZE_512 (0x00000004) /* 001 */ +#define USBCMD_FRAME_SIZE_256 (0x00000008) /* 010 */ +#define USBCMD_FRAME_SIZE_128 (0x0000000C) /* 011 */ +#define USBCMD_FRAME_SIZE_64 (0x00008000) /* 100 */ +#define USBCMD_FRAME_SIZE_32 (0x00008004) /* 101 */ +#define USBCMD_FRAME_SIZE_16 (0x00008008) /* 110 */ +#define USBCMD_FRAME_SIZE_8 (0x0000800C) /* 111 */ + +#define EPCTRL_TX_ALL_MASK (0xFFFF0000) +#define EPCTRL_RX_ALL_MASK (0x0000FFFF) + +#define EPCTRL_TX_DATA_TOGGLE_RST (0x00400000) +#define EPCTRL_TX_EP_STALL (0x00010000) +#define EPCTRL_RX_EP_STALL (0x00000001) +#define EPCTRL_RX_DATA_TOGGLE_RST (0x00000040) +#define EPCTRL_RX_ENABLE (0x00000080) +#define EPCTRL_TX_ENABLE (0x00800000) +#define EPCTRL_CONTROL (0x00000000) +#define EPCTRL_ISOCHRONOUS (0x00040000) +#define EPCTRL_BULK (0x00080000) +#define EPCTRL_INT (0x000C0000) +#define EPCTRL_TX_TYPE (0x000C0000) +#define EPCTRL_RX_TYPE (0x0000000C) +#define EPCTRL_DATA_TOGGLE_INHIBIT (0x00000020) +#define EPCTRL_TX_EP_TYPE_SHIFT (18) +#define EPCTRL_RX_EP_TYPE_SHIFT (2) + +#define EPCOMPLETE_MAX_ENDPOINTS (16) + +/* endpoint list address bit masks */ +#define USB_EP_LIST_ADDRESS_MASK 0xfffff800 + +#define PORTSCX_W1C_BITS 0x2a +#define PORTSCX_PORT_RESET 0x00000100 +#define PORTSCX_PORT_POWER 0x00001000 +#define PORTSCX_FORCE_FULL_SPEED_CONNECT 0x01000000 +#define PORTSCX_PAR_XCVR_SELECT 0xC0000000 +#define PORTSCX_PORT_FORCE_RESUME 0x00000040 +#define PORTSCX_PORT_SUSPEND 0x00000080 +#define PORTSCX_PORT_SPEED_FULL 0x00000000 +#define PORTSCX_PORT_SPEED_LOW 0x04000000 +#define PORTSCX_PORT_SPEED_HIGH 0x08000000 +#define PORTSCX_PORT_SPEED_MASK 0x0C000000 + +/* USB MODE Register Bit Masks */ +#define USBMODE_CTRL_MODE_IDLE 0x00000000 +#define USBMODE_CTRL_MODE_DEVICE 0x00000002 +#define USBMODE_CTRL_MODE_HOST 0x00000003 +#define USBMODE_CTRL_MODE_RSV 0x00000001 +#define USBMODE_SETUP_LOCK_OFF 0x00000008 +#define USBMODE_STREAM_DISABLE 0x00000010 + +/* USB STS Register Bit Masks */ +#define USBSTS_INT 0x00000001 +#define USBSTS_ERR 0x00000002 +#define USBSTS_PORT_CHANGE 0x00000004 +#define USBSTS_FRM_LST_ROLL 0x00000008 +#define USBSTS_SYS_ERR 0x00000010 +#define USBSTS_IAA 0x00000020 +#define USBSTS_RESET 0x00000040 +#define USBSTS_SOF 0x00000080 +#define USBSTS_SUSPEND 0x00000100 +#define USBSTS_HC_HALTED 0x00001000 +#define USBSTS_RCL 0x00002000 +#define USBSTS_PERIODIC_SCHEDULE 0x00004000 +#define USBSTS_ASYNC_SCHEDULE 0x00008000 + + +/* Interrupt Enable Register Bit Masks */ +#define USBINTR_INT_EN (0x00000001) +#define USBINTR_ERR_INT_EN (0x00000002) +#define USBINTR_PORT_CHANGE_DETECT_EN (0x00000004) + +#define USBINTR_ASYNC_ADV_AAE (0x00000020) +#define USBINTR_ASYNC_ADV_AAE_ENABLE (0x00000020) +#define USBINTR_ASYNC_ADV_AAE_DISABLE (0xFFFFFFDF) + +#define USBINTR_RESET_EN (0x00000040) +#define USBINTR_SOF_UFRAME_EN (0x00000080) +#define USBINTR_DEVICE_SUSPEND (0x00000100) + +#define USB_DEVICE_ADDRESS_MASK (0xfe000000) +#define USB_DEVICE_ADDRESS_BIT_SHIFT (25) + +struct mv_cap_regs { + u32 caplength_hciversion; + u32 hcsparams; /* HC structural parameters */ + u32 hccparams; /* HC Capability Parameters*/ + u32 reserved[5]; + u32 dciversion; /* DC version number and reserved 16 bits */ + u32 dccparams; /* DC Capability Parameters */ +}; + +struct mv_op_regs { + u32 usbcmd; /* Command register */ + u32 usbsts; /* Status register */ + u32 usbintr; /* Interrupt enable */ + u32 frindex; /* Frame index */ + u32 reserved1[1]; + u32 deviceaddr; /* Device Address */ + u32 eplistaddr; /* Endpoint List Address */ + u32 ttctrl; /* HOST TT status and control */ + u32 burstsize; /* Programmable Burst Size */ + u32 txfilltuning; /* Host Transmit Pre-Buffer Packet Tuning */ + u32 reserved[4]; + u32 epnak; /* Endpoint NAK */ + u32 epnaken; /* Endpoint NAK Enable */ + u32 configflag; /* Configured Flag register */ + u32 portsc[VUSBHS_MAX_PORTS]; /* Port Status/Control x, x = 1..8 */ + u32 otgsc; + u32 usbmode; /* USB Host/Device mode */ + u32 epsetupstat; /* Endpoint Setup Status */ + u32 epprime; /* Endpoint Initialize */ + u32 epflush; /* Endpoint De-initialize */ + u32 epstatus; /* Endpoint Status */ + u32 epcomplete; /* Endpoint Interrupt On Complete */ + u32 epctrlx[16]; /* Endpoint Control, where x = 0.. 15 */ + u32 mcr; /* Mux Control */ + u32 isr; /* Interrupt Status */ + u32 ier; /* Interrupt Enable */ +}; + +struct mv_udc { + struct usb_gadget gadget; + struct usb_gadget_driver *driver; + spinlock_t lock; + struct completion *done; + struct platform_device *dev; + int irq; + + struct mv_cap_regs __iomem *cap_regs; + struct mv_op_regs __iomem *op_regs; + unsigned int phy_regs; + unsigned int max_eps; + struct mv_dqh *ep_dqh; + size_t ep_dqh_size; + dma_addr_t ep_dqh_dma; + + struct dma_pool *dtd_pool; + struct mv_ep *eps; + + struct mv_dtd *dtd_head; + struct mv_dtd *dtd_tail; + unsigned int dtd_entries; + + struct mv_req *status_req; + struct usb_ctrlrequest local_setup_buff; + + unsigned int resume_state; /* USB state to resume */ + unsigned int usb_state; /* USB current state */ + unsigned int ep0_state; /* Endpoint zero state */ + unsigned int ep0_dir; + + unsigned int dev_addr; + + int errors; + unsigned softconnect:1, + vbus_active:1, + remote_wakeup:1, + softconnected:1, + force_fs:1; + struct clk *clk; +}; + +/* endpoint data structure */ +struct mv_ep { + struct usb_ep ep; + struct mv_udc *udc; + struct list_head queue; + struct mv_dqh *dqh; + const struct usb_endpoint_descriptor *desc; + u32 direction; + char name[14]; + unsigned stopped:1, + wedge:1, + ep_type:2, + ep_num:8; +}; + +/* request data structure */ +struct mv_req { + struct usb_request req; + struct mv_dtd *dtd, *head, *tail; + struct mv_ep *ep; + struct list_head queue; + unsigned dtd_count; + unsigned mapped:1; +}; + +#define EP_QUEUE_HEAD_MULT_POS 30 +#define EP_QUEUE_HEAD_ZLT_SEL 0x20000000 +#define EP_QUEUE_HEAD_MAX_PKT_LEN_POS 16 +#define EP_QUEUE_HEAD_MAX_PKT_LEN(ep_info) (((ep_info)>>16)&0x07ff) +#define EP_QUEUE_HEAD_IOS 0x00008000 +#define EP_QUEUE_HEAD_NEXT_TERMINATE 0x00000001 +#define EP_QUEUE_HEAD_IOC 0x00008000 +#define EP_QUEUE_HEAD_MULTO 0x00000C00 +#define EP_QUEUE_HEAD_STATUS_HALT 0x00000040 +#define EP_QUEUE_HEAD_STATUS_ACTIVE 0x00000080 +#define EP_QUEUE_CURRENT_OFFSET_MASK 0x00000FFF +#define EP_QUEUE_HEAD_NEXT_POINTER_MASK 0xFFFFFFE0 +#define EP_QUEUE_FRINDEX_MASK 0x000007FF +#define EP_MAX_LENGTH_TRANSFER 0x4000 + +struct mv_dqh { + /* Bits 16..26 Bit 15 is Interrupt On Setup */ + u32 max_packet_length; + u32 curr_dtd_ptr; /* Current dTD Pointer */ + u32 next_dtd_ptr; /* Next dTD Pointer */ + /* Total bytes (16..30), IOC (15), INT (8), STS (0-7) */ + u32 size_ioc_int_sts; + u32 buff_ptr0; /* Buffer pointer Page 0 (12-31) */ + u32 buff_ptr1; /* Buffer pointer Page 1 (12-31) */ + u32 buff_ptr2; /* Buffer pointer Page 2 (12-31) */ + u32 buff_ptr3; /* Buffer pointer Page 3 (12-31) */ + u32 buff_ptr4; /* Buffer pointer Page 4 (12-31) */ + u32 reserved1; + /* 8 bytes of setup data that follows the Setup PID */ + u8 setup_buffer[8]; + u32 reserved2[4]; +}; + + +#define DTD_NEXT_TERMINATE (0x00000001) +#define DTD_IOC (0x00008000) +#define DTD_STATUS_ACTIVE (0x00000080) +#define DTD_STATUS_HALTED (0x00000040) +#define DTD_STATUS_DATA_BUFF_ERR (0x00000020) +#define DTD_STATUS_TRANSACTION_ERR (0x00000008) +#define DTD_RESERVED_FIELDS (0x00007F00) +#define DTD_ERROR_MASK (0x68) +#define DTD_ADDR_MASK (0xFFFFFFE0) +#define DTD_PACKET_SIZE 0x7FFF0000 +#define DTD_LENGTH_BIT_POS (16) + +struct mv_dtd { + u32 dtd_next; + u32 size_ioc_sts; + u32 buff_ptr0; /* Buffer pointer Page 0 */ + u32 buff_ptr1; /* Buffer pointer Page 1 */ + u32 buff_ptr2; /* Buffer pointer Page 2 */ + u32 buff_ptr3; /* Buffer pointer Page 3 */ + u32 buff_ptr4; /* Buffer pointer Page 4 */ + u32 scratch_ptr; + /* 32 bytes */ + dma_addr_t td_dma; /* dma address for this td */ + struct mv_dtd *next_dtd_virt; +}; + +extern int mv_udc_phy_init(unsigned int base); + +#endif diff --git a/drivers/usb/gadget/mv_udc_core.c b/drivers/usb/gadget/mv_udc_core.c new file mode 100644 index 000000000000..d5468a7f38e0 --- /dev/null +++ b/drivers/usb/gadget/mv_udc_core.c @@ -0,0 +1,2149 @@ +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/dma-mapping.h> +#include <linux/dmapool.h> +#include <linux/kernel.h> +#include <linux/delay.h> +#include <linux/ioport.h> +#include <linux/sched.h> +#include <linux/slab.h> +#include <linux/errno.h> +#include <linux/init.h> +#include <linux/timer.h> +#include <linux/list.h> +#include <linux/interrupt.h> +#include <linux/moduleparam.h> +#include <linux/device.h> +#include <linux/usb/ch9.h> +#include <linux/usb/gadget.h> +#include <linux/usb/otg.h> +#include <linux/pm.h> +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/platform_device.h> +#include <linux/clk.h> +#include <asm/system.h> +#include <asm/unaligned.h> + +#include "mv_udc.h" + +#define DRIVER_DESC "Marvell PXA USB Device Controller driver" +#define DRIVER_VERSION "8 Nov 2010" + +#define ep_dir(ep) (((ep)->ep_num == 0) ? \ + ((ep)->udc->ep0_dir) : ((ep)->direction)) + +/* timeout value -- usec */ +#define RESET_TIMEOUT 10000 +#define FLUSH_TIMEOUT 10000 +#define EPSTATUS_TIMEOUT 10000 +#define PRIME_TIMEOUT 10000 +#define READSAFE_TIMEOUT 1000 +#define DTD_TIMEOUT 1000 + +#define LOOPS_USEC_SHIFT 4 +#define LOOPS_USEC (1 << LOOPS_USEC_SHIFT) +#define LOOPS(timeout) ((timeout) >> LOOPS_USEC_SHIFT) + +static const char driver_name[] = "mv_udc"; +static const char driver_desc[] = DRIVER_DESC; + +/* controller device global variable */ +static struct mv_udc *the_controller; +int mv_usb_otgsc; + +static void nuke(struct mv_ep *ep, int status); + +/* for endpoint 0 operations */ +static const struct usb_endpoint_descriptor mv_ep0_desc = { + .bLength = USB_DT_ENDPOINT_SIZE, + .bDescriptorType = USB_DT_ENDPOINT, + .bEndpointAddress = 0, + .bmAttributes = USB_ENDPOINT_XFER_CONTROL, + .wMaxPacketSize = EP0_MAX_PKT_SIZE, +}; + +static void ep0_reset(struct mv_udc *udc) +{ + struct mv_ep *ep; + u32 epctrlx; + int i = 0; + + /* ep0 in and out */ + for (i = 0; i < 2; i++) { + ep = &udc->eps[i]; + ep->udc = udc; + + /* ep0 dQH */ + ep->dqh = &udc->ep_dqh[i]; + + /* configure ep0 endpoint capabilities in dQH */ + ep->dqh->max_packet_length = + (EP0_MAX_PKT_SIZE << EP_QUEUE_HEAD_MAX_PKT_LEN_POS) + | EP_QUEUE_HEAD_IOS; + + epctrlx = readl(&udc->op_regs->epctrlx[0]); + if (i) { /* TX */ + epctrlx |= EPCTRL_TX_ENABLE | EPCTRL_TX_DATA_TOGGLE_RST + | (USB_ENDPOINT_XFER_CONTROL + << EPCTRL_TX_EP_TYPE_SHIFT); + + } else { /* RX */ + epctrlx |= EPCTRL_RX_ENABLE | EPCTRL_RX_DATA_TOGGLE_RST + | (USB_ENDPOINT_XFER_CONTROL + << EPCTRL_RX_EP_TYPE_SHIFT); + } + + writel(epctrlx, &udc->op_regs->epctrlx[0]); + } +} + +/* protocol ep0 stall, will automatically be cleared on new transaction */ +static void ep0_stall(struct mv_udc *udc) +{ + u32 epctrlx; + + /* set TX and RX to stall */ + epctrlx = readl(&udc->op_regs->epctrlx[0]); + epctrlx |= EPCTRL_RX_EP_STALL | EPCTRL_TX_EP_STALL; + writel(epctrlx, &udc->op_regs->epctrlx[0]); + + /* update ep0 state */ + udc->ep0_state = WAIT_FOR_SETUP; + udc->ep0_dir = EP_DIR_OUT; +} + +static int process_ep_req(struct mv_udc *udc, int index, + struct mv_req *curr_req) +{ + struct mv_dtd *curr_dtd; + struct mv_dqh *curr_dqh; + int td_complete, actual, remaining_length; + int i, direction; + int retval = 0; + u32 errors; + + curr_dqh = &udc->ep_dqh[index]; + direction = index % 2; + + curr_dtd = curr_req->head; + td_complete = 0; + actual = curr_req->req.length; + + for (i = 0; i < curr_req->dtd_count; i++) { + if (curr_dtd->size_ioc_sts & DTD_STATUS_ACTIVE) { + dev_dbg(&udc->dev->dev, "%s, dTD not completed\n", + udc->eps[index].name); + return 1; + } + + errors = curr_dtd->size_ioc_sts & DTD_ERROR_MASK; + if (!errors) { + remaining_length += + (curr_dtd->size_ioc_sts & DTD_PACKET_SIZE) + >> DTD_LENGTH_BIT_POS; + actual -= remaining_length; + } else { + dev_info(&udc->dev->dev, + "complete_tr error: ep=%d %s: error = 0x%x\n", + index >> 1, direction ? "SEND" : "RECV", + errors); + if (errors & DTD_STATUS_HALTED) { + /* Clear the errors and Halt condition */ + curr_dqh->size_ioc_int_sts &= ~errors; + retval = -EPIPE; + } else if (errors & DTD_STATUS_DATA_BUFF_ERR) { + retval = -EPROTO; + } else if (errors & DTD_STATUS_TRANSACTION_ERR) { + retval = -EILSEQ; + } + } + if (i != curr_req->dtd_count - 1) + curr_dtd = (struct mv_dtd *)curr_dtd->next_dtd_virt; + } + if (retval) + return retval; + + curr_req->req.actual = actual; + + return 0; +} + +/* + * done() - retire a request; caller blocked irqs + * @status : request status to be set, only works when + * request is still in progress. + */ +static void done(struct mv_ep *ep, struct mv_req *req, int status) +{ + struct mv_udc *udc = NULL; + unsigned char stopped = ep->stopped; + struct mv_dtd *curr_td, *next_td; + int j; + + udc = (struct mv_udc *)ep->udc; + /* Removed the req from fsl_ep->queue */ + list_del_init(&req->queue); + + /* req.status should be set as -EINPROGRESS in ep_queue() */ + if (req->req.status == -EINPROGRESS) + req->req.status = status; + else + status = req->req.status; + + /* Free dtd for the request */ + next_td = req->head; + for (j = 0; j < req->dtd_count; j++) { + curr_td = next_td; + if (j != req->dtd_count - 1) + next_td = curr_td->next_dtd_virt; + dma_pool_free(udc->dtd_pool, curr_td, curr_td->td_dma); + } + + if (req->mapped) { + dma_unmap_single(ep->udc->gadget.dev.parent, + req->req.dma, req->req.length, + ((ep_dir(ep) == EP_DIR_IN) ? + DMA_TO_DEVICE : DMA_FROM_DEVICE)); + req->req.dma = DMA_ADDR_INVALID; + req->mapped = 0; + } else + dma_sync_single_for_cpu(ep->udc->gadget.dev.parent, + req->req.dma, req->req.length, + ((ep_dir(ep) == EP_DIR_IN) ? + DMA_TO_DEVICE : DMA_FROM_DEVICE)); + + if (status && (status != -ESHUTDOWN)) + dev_info(&udc->dev->dev, "complete %s req %p stat %d len %u/%u", + ep->ep.name, &req->req, status, + req->req.actual, req->req.length); + + ep->stopped = 1; + + spin_unlock(&ep->udc->lock); + /* + * complete() is from gadget layer, + * eg fsg->bulk_in_complete() + */ + if (req->req.complete) + req->req.complete(&ep->ep, &req->req); + + spin_lock(&ep->udc->lock); + ep->stopped = stopped; +} + +static int queue_dtd(struct mv_ep *ep, struct mv_req *req) +{ + u32 tmp, epstatus, bit_pos, direction; + struct mv_udc *udc; + struct mv_dqh *dqh; + unsigned int loops; + int readsafe, retval = 0; + + udc = ep->udc; + direction = ep_dir(ep); + dqh = &(udc->ep_dqh[ep->ep_num * 2 + direction]); + bit_pos = 1 << (((direction == EP_DIR_OUT) ? 0 : 16) + ep->ep_num); + + /* check if the pipe is empty */ + if (!(list_empty(&ep->queue))) { + struct mv_req *lastreq; + lastreq = list_entry(ep->queue.prev, struct mv_req, queue); + lastreq->tail->dtd_next = + req->head->td_dma & EP_QUEUE_HEAD_NEXT_POINTER_MASK; + if (readl(&udc->op_regs->epprime) & bit_pos) { + loops = LOOPS(PRIME_TIMEOUT); + while (readl(&udc->op_regs->epprime) & bit_pos) { + if (loops == 0) { + retval = -ETIME; + goto done; + } + udelay(LOOPS_USEC); + loops--; + } + if (readl(&udc->op_regs->epstatus) & bit_pos) + goto done; + } + readsafe = 0; + loops = LOOPS(READSAFE_TIMEOUT); + while (readsafe == 0) { + if (loops == 0) { + retval = -ETIME; + goto done; + } + /* start with setting the semaphores */ + tmp = readl(&udc->op_regs->usbcmd); + tmp |= USBCMD_ATDTW_TRIPWIRE_SET; + writel(tmp, &udc->op_regs->usbcmd); + + /* read the endpoint status */ + epstatus = readl(&udc->op_regs->epstatus) & bit_pos; + + /* + * Reread the ATDTW semaphore bit to check if it is + * cleared. When hardware see a hazard, it will clear + * the bit or else we remain set to 1 and we can + * proceed with priming of endpoint if not already + * primed. + */ + if (readl(&udc->op_regs->usbcmd) + & USBCMD_ATDTW_TRIPWIRE_SET) { + readsafe = 1; + } + loops--; + udelay(LOOPS_USEC); + } + + /* Clear the semaphore */ + tmp = readl(&udc->op_regs->usbcmd); + tmp &= USBCMD_ATDTW_TRIPWIRE_CLEAR; + writel(tmp, &udc->op_regs->usbcmd); + + /* If endpoint is not active, we activate it now. */ + if (!epstatus) { + if (direction == EP_DIR_IN) { + struct mv_dtd *curr_dtd = dma_to_virt( + &udc->dev->dev, dqh->curr_dtd_ptr); + + loops = LOOPS(DTD_TIMEOUT); + while (curr_dtd->size_ioc_sts + & DTD_STATUS_ACTIVE) { + if (loops == 0) { + retval = -ETIME; + goto done; + } + loops--; + udelay(LOOPS_USEC); + } + } + /* No other transfers on the queue */ + + /* Write dQH next pointer and terminate bit to 0 */ + dqh->next_dtd_ptr = req->head->td_dma + & EP_QUEUE_HEAD_NEXT_POINTER_MASK; + dqh->size_ioc_int_sts = 0; + + /* + * Ensure that updates to the QH will + * occure before priming. + */ + wmb(); + + /* Prime the Endpoint */ + writel(bit_pos, &udc->op_regs->epprime); + } + } else { + /* Write dQH next pointer and terminate bit to 0 */ + dqh->next_dtd_ptr = req->head->td_dma + & EP_QUEUE_HEAD_NEXT_POINTER_MASK;; + dqh->size_ioc_int_sts = 0; + + /* Ensure that updates to the QH will occure before priming. */ + wmb(); + + /* Prime the Endpoint */ + writel(bit_pos, &udc->op_regs->epprime); + + if (direction == EP_DIR_IN) { + /* FIXME add status check after prime the IN ep */ + int prime_again; + u32 curr_dtd_ptr = dqh->curr_dtd_ptr; + + loops = LOOPS(DTD_TIMEOUT); + prime_again = 0; + while ((curr_dtd_ptr != req->head->td_dma)) { + curr_dtd_ptr = dqh->curr_dtd_ptr; + if (loops == 0) { + dev_err(&udc->dev->dev, + "failed to prime %s\n", + ep->name); + retval = -ETIME; + goto done; + } + loops--; + udelay(LOOPS_USEC); + + if (loops == (LOOPS(DTD_TIMEOUT) >> 2)) { + if (prime_again) + goto done; + dev_info(&udc->dev->dev, + "prime again\n"); + writel(bit_pos, + &udc->op_regs->epprime); + prime_again = 1; + } + } + } + } +done: + return retval;; +} + +static struct mv_dtd *build_dtd(struct mv_req *req, unsigned *length, + dma_addr_t *dma, int *is_last) +{ + u32 temp; + struct mv_dtd *dtd; + struct mv_udc *udc; + + /* how big will this transfer be? */ + *length = min(req->req.length - req->req.actual, + (unsigned)EP_MAX_LENGTH_TRANSFER); + + udc = req->ep->udc; + + /* + * Be careful that no _GFP_HIGHMEM is set, + * or we can not use dma_to_virt + */ + dtd = dma_pool_alloc(udc->dtd_pool, GFP_KERNEL, dma); + if (dtd == NULL) + return dtd; + + dtd->td_dma = *dma; + /* initialize buffer page pointers */ + temp = (u32)(req->req.dma + req->req.actual); + dtd->buff_ptr0 = cpu_to_le32(temp); + temp &= ~0xFFF; + dtd->buff_ptr1 = cpu_to_le32(temp + 0x1000); + dtd->buff_ptr2 = cpu_to_le32(temp + 0x2000); + dtd->buff_ptr3 = cpu_to_le32(temp + 0x3000); + dtd->buff_ptr4 = cpu_to_le32(temp + 0x4000); + + req->req.actual += *length; + + /* zlp is needed if req->req.zero is set */ + if (req->req.zero) { + if (*length == 0 || (*length % req->ep->ep.maxpacket) != 0) + *is_last = 1; + else + *is_last = 0; + } else if (req->req.length == req->req.actual) + *is_last = 1; + else + *is_last = 0; + + /* Fill in the transfer size; set active bit */ + temp = ((*length << DTD_LENGTH_BIT_POS) | DTD_STATUS_ACTIVE); + + /* Enable interrupt for the last dtd of a request */ + if (*is_last && !req->req.no_interrupt) + temp |= DTD_IOC; + + dtd->size_ioc_sts = temp; + + mb(); + + return dtd; +} + +/* generate dTD linked list for a request */ +static int req_to_dtd(struct mv_req *req) +{ + unsigned count; + int is_last, is_first = 1; + struct mv_dtd *dtd, *last_dtd = NULL; + struct mv_udc *udc; + dma_addr_t dma; + + udc = req->ep->udc; + + do { + dtd = build_dtd(req, &count, &dma, &is_last); + if (dtd == NULL) + return -ENOMEM; + + if (is_first) { + is_first = 0; + req->head = dtd; + } else { + last_dtd->dtd_next = dma; + last_dtd->next_dtd_virt = dtd; + } + last_dtd = dtd; + req->dtd_count++; + } while (!is_last); + + /* set terminate bit to 1 for the last dTD */ + dtd->dtd_next = DTD_NEXT_TERMINATE; + + req->tail = dtd; + + return 0; +} + +static int mv_ep_enable(struct usb_ep *_ep, + const struct usb_endpoint_descriptor *desc) +{ + struct mv_udc *udc; + struct mv_ep *ep; + struct mv_dqh *dqh; + u16 max = 0; + u32 bit_pos, epctrlx, direction; + unsigned char zlt = 0, ios = 0, mult = 0; + + ep = container_of(_ep, struct mv_ep, ep); + udc = ep->udc; + + if (!_ep || !desc || ep->desc + || desc->bDescriptorType != USB_DT_ENDPOINT) + return -EINVAL; + + if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN) + return -ESHUTDOWN; + + direction = ep_dir(ep); + max = le16_to_cpu(desc->wMaxPacketSize); + + /* + * disable HW zero length termination select + * driver handles zero length packet through req->req.zero + */ + zlt = 1; + + /* Get the endpoint queue head address */ + dqh = (struct mv_dqh *)ep->dqh; + + bit_pos = 1 << ((direction == EP_DIR_OUT ? 0 : 16) + ep->ep_num); + + /* Check if the Endpoint is Primed */ + if ((readl(&udc->op_regs->epprime) & bit_pos) + || (readl(&udc->op_regs->epstatus) & bit_pos)) { + dev_info(&udc->dev->dev, + "ep=%d %s: Init ERROR: ENDPTPRIME=0x%x," + " ENDPTSTATUS=0x%x, bit_pos=0x%x\n", + (unsigned)ep->ep_num, direction ? "SEND" : "RECV", + (unsigned)readl(&udc->op_regs->epprime), + (unsigned)readl(&udc->op_regs->epstatus), + (unsigned)bit_pos); + goto en_done; + } + /* Set the max packet length, interrupt on Setup and Mult fields */ + switch (desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) { + case USB_ENDPOINT_XFER_BULK: + zlt = 1; + mult = 0; + break; + case USB_ENDPOINT_XFER_CONTROL: + ios = 1; + case USB_ENDPOINT_XFER_INT: + mult = 0; + break; + case USB_ENDPOINT_XFER_ISOC: + /* Calculate transactions needed for high bandwidth iso */ + mult = (unsigned char)(1 + ((max >> 11) & 0x03)); + max = max & 0x8ff; /* bit 0~10 */ + /* 3 transactions at most */ + if (mult > 3) + goto en_done; + break; + default: + goto en_done; + } + dqh->max_packet_length = (max << EP_QUEUE_HEAD_MAX_PKT_LEN_POS) + | (mult << EP_QUEUE_HEAD_MULT_POS) + | (zlt ? EP_QUEUE_HEAD_ZLT_SEL : 0) + | (ios ? EP_QUEUE_HEAD_IOS : 0); + dqh->next_dtd_ptr = 1; + dqh->size_ioc_int_sts = 0; + + ep->ep.maxpacket = max; + ep->desc = desc; + ep->stopped = 0; + + /* Enable the endpoint for Rx or Tx and set the endpoint type */ + epctrlx = readl(&udc->op_regs->epctrlx[ep->ep_num]); + if (direction == EP_DIR_IN) { + epctrlx &= ~EPCTRL_TX_ALL_MASK; + epctrlx |= EPCTRL_TX_ENABLE | EPCTRL_TX_DATA_TOGGLE_RST + | ((desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) + << EPCTRL_TX_EP_TYPE_SHIFT); + } else { + epctrlx &= ~EPCTRL_RX_ALL_MASK; + epctrlx |= EPCTRL_RX_ENABLE | EPCTRL_RX_DATA_TOGGLE_RST + | ((desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) + << EPCTRL_RX_EP_TYPE_SHIFT); + } + writel(epctrlx, &udc->op_regs->epctrlx[ep->ep_num]); + + /* + * Implement Guideline (GL# USB-7) The unused endpoint type must + * be programmed to bulk. + */ + epctrlx = readl(&udc->op_regs->epctrlx[ep->ep_num]); + if ((epctrlx & EPCTRL_RX_ENABLE) == 0) { + epctrlx |= ((desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) + << EPCTRL_RX_EP_TYPE_SHIFT); + writel(epctrlx, &udc->op_regs->epctrlx[ep->ep_num]); + } + + epctrlx = readl(&udc->op_regs->epctrlx[ep->ep_num]); + if ((epctrlx & EPCTRL_TX_ENABLE) == 0) { + epctrlx |= ((desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) + << EPCTRL_TX_EP_TYPE_SHIFT); + writel(epctrlx, &udc->op_regs->epctrlx[ep->ep_num]); + } + + return 0; +en_done: + return -EINVAL; +} + +static int mv_ep_disable(struct usb_ep *_ep) +{ + struct mv_udc *udc; + struct mv_ep *ep; + struct mv_dqh *dqh; + u32 bit_pos, epctrlx, direction; + + ep = container_of(_ep, struct mv_ep, ep); + if ((_ep == NULL) || !ep->desc) + return -EINVAL; + + udc = ep->udc; + + /* Get the endpoint queue head address */ + dqh = ep->dqh; + + direction = ep_dir(ep); + bit_pos = 1 << ((direction == EP_DIR_OUT ? 0 : 16) + ep->ep_num); + + /* Reset the max packet length and the interrupt on Setup */ + dqh->max_packet_length = 0; + + /* Disable the endpoint for Rx or Tx and reset the endpoint type */ + epctrlx = readl(&udc->op_regs->epctrlx[ep->ep_num]); + epctrlx &= ~((direction == EP_DIR_IN) + ? (EPCTRL_TX_ENABLE | EPCTRL_TX_TYPE) + : (EPCTRL_RX_ENABLE | EPCTRL_RX_TYPE)); + writel(epctrlx, &udc->op_regs->epctrlx[ep->ep_num]); + + /* nuke all pending requests (does flush) */ + nuke(ep, -ESHUTDOWN); + + ep->desc = NULL; + ep->stopped = 1; + return 0; +} + +static struct usb_request * +mv_alloc_request(struct usb_ep *_ep, gfp_t gfp_flags) +{ + struct mv_req *req = NULL; + + req = kzalloc(sizeof *req, gfp_flags); + if (!req) + return NULL; + + req->req.dma = DMA_ADDR_INVALID; + INIT_LIST_HEAD(&req->queue); + + return &req->req; +} + +static void mv_free_request(struct usb_ep *_ep, struct usb_request *_req) +{ + struct mv_req *req = NULL; + + req = container_of(_req, struct mv_req, req); + + if (_req) + kfree(req); +} + +static void mv_ep_fifo_flush(struct usb_ep *_ep) +{ + struct mv_udc *udc; + u32 bit_pos, direction; + struct mv_ep *ep = container_of(_ep, struct mv_ep, ep); + unsigned int loops; + + udc = ep->udc; + direction = ep_dir(ep); + bit_pos = 1 << ((direction == EP_DIR_OUT ? 0 : 16) + ep->ep_num); + /* + * Flushing will halt the pipe + * Write 1 to the Flush register + */ + writel(bit_pos, &udc->op_regs->epflush); + + /* Wait until flushing completed */ + loops = LOOPS(FLUSH_TIMEOUT); + while (readl(&udc->op_regs->epflush) & bit_pos) { + /* + * ENDPTFLUSH bit should be cleared to indicate this + * operation is complete + */ + if (loops == 0) { + dev_err(&udc->dev->dev, + "TIMEOUT for ENDPTFLUSH=0x%x, bit_pos=0x%x\n", + (unsigned)readl(&udc->op_regs->epflush), + (unsigned)bit_pos); + return; + } + loops--; + udelay(LOOPS_USEC); + } + loops = LOOPS(EPSTATUS_TIMEOUT); + while (readl(&udc->op_regs->epstatus) & bit_pos) { + unsigned int inter_loops; + + if (loops == 0) { + dev_err(&udc->dev->dev, + "TIMEOUT for ENDPTSTATUS=0x%x, bit_pos=0x%x\n", + (unsigned)readl(&udc->op_regs->epstatus), + (unsigned)bit_pos); + return; + } + /* Write 1 to the Flush register */ + writel(bit_pos, &udc->op_regs->epflush); + + /* Wait until flushing completed */ + inter_loops = LOOPS(FLUSH_TIMEOUT); + while (readl(&udc->op_regs->epflush) & bit_pos) { + /* + * ENDPTFLUSH bit should be cleared to indicate this + * operation is complete + */ + if (inter_loops == 0) { + dev_err(&udc->dev->dev, + "TIMEOUT for ENDPTFLUSH=0x%x," + "bit_pos=0x%x\n", + (unsigned)readl(&udc->op_regs->epflush), + (unsigned)bit_pos); + return; + } + inter_loops--; + udelay(LOOPS_USEC); + } + loops--; + } +} + +/* queues (submits) an I/O request to an endpoint */ +static int +mv_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) +{ + struct mv_ep *ep = container_of(_ep, struct mv_ep, ep); + struct mv_req *req = container_of(_req, struct mv_req, req); + struct mv_udc *udc = ep->udc; + unsigned long flags; + + /* catch various bogus parameters */ + if (!_req || !req->req.complete || !req->req.buf + || !list_empty(&req->queue)) { + dev_err(&udc->dev->dev, "%s, bad params", __func__); + return -EINVAL; + } + if (unlikely(!_ep || !ep->desc)) { + dev_err(&udc->dev->dev, "%s, bad ep", __func__); + return -EINVAL; + } + if (ep->desc->bmAttributes == USB_ENDPOINT_XFER_ISOC) { + if (req->req.length > ep->ep.maxpacket) + return -EMSGSIZE; + } + + udc = ep->udc; + if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN) + return -ESHUTDOWN; + + req->ep = ep; + + /* map virtual address to hardware */ + if (req->req.dma == DMA_ADDR_INVALID) { + req->req.dma = dma_map_single(ep->udc->gadget.dev.parent, + req->req.buf, + req->req.length, ep_dir(ep) + ? DMA_TO_DEVICE + : DMA_FROM_DEVICE); + req->mapped = 1; + } else { + dma_sync_single_for_device(ep->udc->gadget.dev.parent, + req->req.dma, req->req.length, + ep_dir(ep) + ? DMA_TO_DEVICE + : DMA_FROM_DEVICE); + req->mapped = 0; + } + + req->req.status = -EINPROGRESS; + req->req.actual = 0; + req->dtd_count = 0; + + spin_lock_irqsave(&udc->lock, flags); + + /* build dtds and push them to device queue */ + if (!req_to_dtd(req)) { + int retval; + retval = queue_dtd(ep, req); + if (retval) { + spin_unlock_irqrestore(&udc->lock, flags); + return retval; + } + } else { + spin_unlock_irqrestore(&udc->lock, flags); + return -ENOMEM; + } + + /* Update ep0 state */ + if (ep->ep_num == 0) + udc->ep0_state = DATA_STATE_XMIT; + + /* irq handler advances the queue */ + if (req != NULL) + list_add_tail(&req->queue, &ep->queue); + spin_unlock_irqrestore(&udc->lock, flags); + + return 0; +} + +/* dequeues (cancels, unlinks) an I/O request from an endpoint */ +static int mv_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req) +{ + struct mv_ep *ep = container_of(_ep, struct mv_ep, ep); + struct mv_req *req; + struct mv_udc *udc = ep->udc; + unsigned long flags; + int stopped, ret = 0; + u32 epctrlx; + + if (!_ep || !_req) + return -EINVAL; + + spin_lock_irqsave(&ep->udc->lock, flags); + stopped = ep->stopped; + + /* Stop the ep before we deal with the queue */ + ep->stopped = 1; + epctrlx = readl(&udc->op_regs->epctrlx[ep->ep_num]); + if (ep_dir(ep) == EP_DIR_IN) + epctrlx &= ~EPCTRL_TX_ENABLE; + else + epctrlx &= ~EPCTRL_RX_ENABLE; + writel(epctrlx, &udc->op_regs->epctrlx[ep->ep_num]); + + /* make sure it's actually queued on this endpoint */ + list_for_each_entry(req, &ep->queue, queue) { + if (&req->req == _req) + break; + } + if (&req->req != _req) { + ret = -EINVAL; + goto out; + } + + /* The request is in progress, or completed but not dequeued */ + if (ep->queue.next == &req->queue) { + _req->status = -ECONNRESET; + mv_ep_fifo_flush(_ep); /* flush current transfer */ + + /* The request isn't the last request in this ep queue */ + if (req->queue.next != &ep->queue) { + struct mv_dqh *qh; + struct mv_req *next_req; + + qh = ep->dqh; + next_req = list_entry(req->queue.next, struct mv_req, + queue); + + /* Point the QH to the first TD of next request */ + writel((u32) next_req->head, &qh->curr_dtd_ptr); + } else { + struct mv_dqh *qh; + + qh = ep->dqh; + qh->next_dtd_ptr = 1; + qh->size_ioc_int_sts = 0; + } + + /* The request hasn't been processed, patch up the TD chain */ + } else { + struct mv_req *prev_req; + + prev_req = list_entry(req->queue.prev, struct mv_req, queue); + writel(readl(&req->tail->dtd_next), + &prev_req->tail->dtd_next); + + } + + done(ep, req, -ECONNRESET); + + /* Enable EP */ +out: + epctrlx = readl(&udc->op_regs->epctrlx[ep->ep_num]); + if (ep_dir(ep) == EP_DIR_IN) + epctrlx |= EPCTRL_TX_ENABLE; + else + epctrlx |= EPCTRL_RX_ENABLE; + writel(epctrlx, &udc->op_regs->epctrlx[ep->ep_num]); + ep->stopped = stopped; + + spin_unlock_irqrestore(&ep->udc->lock, flags); + return ret; +} + +static void ep_set_stall(struct mv_udc *udc, u8 ep_num, u8 direction, int stall) +{ + u32 epctrlx; + + epctrlx = readl(&udc->op_regs->epctrlx[ep_num]); + + if (stall) { + if (direction == EP_DIR_IN) + epctrlx |= EPCTRL_TX_EP_STALL; + else + epctrlx |= EPCTRL_RX_EP_STALL; + } else { + if (direction == EP_DIR_IN) { + epctrlx &= ~EPCTRL_TX_EP_STALL; + epctrlx |= EPCTRL_TX_DATA_TOGGLE_RST; + } else { + epctrlx &= ~EPCTRL_RX_EP_STALL; + epctrlx |= EPCTRL_RX_DATA_TOGGLE_RST; + } + } + writel(epctrlx, &udc->op_regs->epctrlx[ep_num]); +} + +static int ep_is_stall(struct mv_udc *udc, u8 ep_num, u8 direction) +{ + u32 epctrlx; + + epctrlx = readl(&udc->op_regs->epctrlx[ep_num]); + + if (direction == EP_DIR_OUT) + return (epctrlx & EPCTRL_RX_EP_STALL) ? 1 : 0; + else + return (epctrlx & EPCTRL_TX_EP_STALL) ? 1 : 0; +} + +static int mv_ep_set_halt_wedge(struct usb_ep *_ep, int halt, int wedge) +{ + struct mv_ep *ep; + unsigned long flags = 0; + int status = 0; + struct mv_udc *udc; + + ep = container_of(_ep, struct mv_ep, ep); + udc = ep->udc; + if (!_ep || !ep->desc) { + status = -EINVAL; + goto out; + } + + if (ep->desc->bmAttributes == USB_ENDPOINT_XFER_ISOC) { + status = -EOPNOTSUPP; + goto out; + } + + /* + * Attempt to halt IN ep will fail if any transfer requests + * are still queue + */ + if (halt && (ep_dir(ep) == EP_DIR_IN) && !list_empty(&ep->queue)) { + status = -EAGAIN; + goto out; + } + + spin_lock_irqsave(&ep->udc->lock, flags); + ep_set_stall(udc, ep->ep_num, ep_dir(ep), halt); + if (halt && wedge) + ep->wedge = 1; + else if (!halt) + ep->wedge = 0; + spin_unlock_irqrestore(&ep->udc->lock, flags); + + if (ep->ep_num == 0) { + udc->ep0_state = WAIT_FOR_SETUP; + udc->ep0_dir = EP_DIR_OUT; + } +out: + return status; +} + +static int mv_ep_set_halt(struct usb_ep *_ep, int halt) +{ + return mv_ep_set_halt_wedge(_ep, halt, 0); +} + +static int mv_ep_set_wedge(struct usb_ep *_ep) +{ + return mv_ep_set_halt_wedge(_ep, 1, 1); +} + +static struct usb_ep_ops mv_ep_ops = { + .enable = mv_ep_enable, + .disable = mv_ep_disable, + + .alloc_request = mv_alloc_request, + .free_request = mv_free_request, + + .queue = mv_ep_queue, + .dequeue = mv_ep_dequeue, + + .set_wedge = mv_ep_set_wedge, + .set_halt = mv_ep_set_halt, + .fifo_flush = mv_ep_fifo_flush, /* flush fifo */ +}; + +static void udc_stop(struct mv_udc *udc) +{ + u32 tmp; + + /* Disable interrupts */ + tmp = readl(&udc->op_regs->usbintr); + tmp &= ~(USBINTR_INT_EN | USBINTR_ERR_INT_EN | + USBINTR_PORT_CHANGE_DETECT_EN | USBINTR_RESET_EN); + writel(tmp, &udc->op_regs->usbintr); + + /* Reset the Run the bit in the command register to stop VUSB */ + tmp = readl(&udc->op_regs->usbcmd); + tmp &= ~USBCMD_RUN_STOP; + writel(tmp, &udc->op_regs->usbcmd); +} + +static void udc_start(struct mv_udc *udc) +{ + u32 usbintr; + + usbintr = USBINTR_INT_EN | USBINTR_ERR_INT_EN + | USBINTR_PORT_CHANGE_DETECT_EN + | USBINTR_RESET_EN | USBINTR_DEVICE_SUSPEND; + /* Enable interrupts */ + writel(usbintr, &udc->op_regs->usbintr); + + /* Set the Run bit in the command register */ + writel(USBCMD_RUN_STOP, &udc->op_regs->usbcmd); +} + +static int udc_reset(struct mv_udc *udc) +{ + unsigned int loops; + u32 tmp, portsc; + + /* Stop the controller */ + tmp = readl(&udc->op_regs->usbcmd); + tmp &= ~USBCMD_RUN_STOP; + writel(tmp, &udc->op_regs->usbcmd); + + /* Reset the controller to get default values */ + writel(USBCMD_CTRL_RESET, &udc->op_regs->usbcmd); + + /* wait for reset to complete */ + loops = LOOPS(RESET_TIMEOUT); + while (readl(&udc->op_regs->usbcmd) & USBCMD_CTRL_RESET) { + if (loops == 0) { + dev_err(&udc->dev->dev, + "Wait for RESET completed TIMEOUT\n"); + return -ETIMEDOUT; + } + loops--; + udelay(LOOPS_USEC); + } + + /* set controller to device mode */ + tmp = readl(&udc->op_regs->usbmode); + tmp |= USBMODE_CTRL_MODE_DEVICE; + + /* turn setup lockout off, require setup tripwire in usbcmd */ + tmp |= USBMODE_SETUP_LOCK_OFF | USBMODE_STREAM_DISABLE; + + writel(tmp, &udc->op_regs->usbmode); + + writel(0x0, &udc->op_regs->epsetupstat); + + /* Configure the Endpoint List Address */ + writel(udc->ep_dqh_dma & USB_EP_LIST_ADDRESS_MASK, + &udc->op_regs->eplistaddr); + + portsc = readl(&udc->op_regs->portsc[0]); + if (readl(&udc->cap_regs->hcsparams) & HCSPARAMS_PPC) + portsc &= (~PORTSCX_W1C_BITS | ~PORTSCX_PORT_POWER); + + if (udc->force_fs) + portsc |= PORTSCX_FORCE_FULL_SPEED_CONNECT; + else + portsc &= (~PORTSCX_FORCE_FULL_SPEED_CONNECT); + + writel(portsc, &udc->op_regs->portsc[0]); + + tmp = readl(&udc->op_regs->epctrlx[0]); + tmp &= ~(EPCTRL_TX_EP_STALL | EPCTRL_RX_EP_STALL); + writel(tmp, &udc->op_regs->epctrlx[0]); + + return 0; +} + +static int mv_udc_get_frame(struct usb_gadget *gadget) +{ + struct mv_udc *udc; + u16 retval; + + if (!gadget) + return -ENODEV; + + udc = container_of(gadget, struct mv_udc, gadget); + + retval = readl(udc->op_regs->frindex) & USB_FRINDEX_MASKS; + + return retval; +} + +/* Tries to wake up the host connected to this gadget */ +static int mv_udc_wakeup(struct usb_gadget *gadget) +{ + struct mv_udc *udc = container_of(gadget, struct mv_udc, gadget); + u32 portsc; + + /* Remote wakeup feature not enabled by host */ + if (!udc->remote_wakeup) + return -ENOTSUPP; + + portsc = readl(&udc->op_regs->portsc); + /* not suspended? */ + if (!(portsc & PORTSCX_PORT_SUSPEND)) + return 0; + /* trigger force resume */ + portsc |= PORTSCX_PORT_FORCE_RESUME; + writel(portsc, &udc->op_regs->portsc[0]); + return 0; +} + +static int mv_udc_pullup(struct usb_gadget *gadget, int is_on) +{ + struct mv_udc *udc; + unsigned long flags; + + udc = container_of(gadget, struct mv_udc, gadget); + spin_lock_irqsave(&udc->lock, flags); + + udc->softconnect = (is_on != 0); + if (udc->driver && udc->softconnect) + udc_start(udc); + else + udc_stop(udc); + + spin_unlock_irqrestore(&udc->lock, flags); + return 0; +} + +/* device controller usb_gadget_ops structure */ +static const struct usb_gadget_ops mv_ops = { + + /* returns the current frame number */ + .get_frame = mv_udc_get_frame, + + /* tries to wake up the host connected to this gadget */ + .wakeup = mv_udc_wakeup, + + /* D+ pullup, software-controlled connect/disconnect to USB host */ + .pullup = mv_udc_pullup, +}; + +static void mv_udc_testmode(struct mv_udc *udc, u16 index, bool enter) +{ + dev_info(&udc->dev->dev, "Test Mode is not support yet\n"); +} + +static int eps_init(struct mv_udc *udc) +{ + struct mv_ep *ep; + char name[14]; + int i; + + /* initialize ep0 */ + ep = &udc->eps[0]; + ep->udc = udc; + strncpy(ep->name, "ep0", sizeof(ep->name)); + ep->ep.name = ep->name; + ep->ep.ops = &mv_ep_ops; + ep->wedge = 0; + ep->stopped = 0; + ep->ep.maxpacket = EP0_MAX_PKT_SIZE; + ep->ep_num = 0; + ep->desc = &mv_ep0_desc; + INIT_LIST_HEAD(&ep->queue); + + ep->ep_type = USB_ENDPOINT_XFER_CONTROL; + + /* initialize other endpoints */ + for (i = 2; i < udc->max_eps * 2; i++) { + ep = &udc->eps[i]; + if (i % 2) { + snprintf(name, sizeof(name), "ep%din", i / 2); + ep->direction = EP_DIR_IN; + } else { + snprintf(name, sizeof(name), "ep%dout", i / 2); + ep->direction = EP_DIR_OUT; + } + ep->udc = udc; + strncpy(ep->name, name, sizeof(ep->name)); + ep->ep.name = ep->name; + + ep->ep.ops = &mv_ep_ops; + ep->stopped = 0; + ep->ep.maxpacket = (unsigned short) ~0; + ep->ep_num = i / 2; + + INIT_LIST_HEAD(&ep->queue); + list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list); + + ep->dqh = &udc->ep_dqh[i]; + } + + return 0; +} + +/* delete all endpoint requests, called with spinlock held */ +static void nuke(struct mv_ep *ep, int status) +{ + /* called with spinlock held */ + ep->stopped = 1; + + /* endpoint fifo flush */ + mv_ep_fifo_flush(&ep->ep); + + while (!list_empty(&ep->queue)) { + struct mv_req *req = NULL; + req = list_entry(ep->queue.next, struct mv_req, queue); + done(ep, req, status); + } +} + +/* stop all USB activities */ +static void stop_activity(struct mv_udc *udc, struct usb_gadget_driver *driver) +{ + struct mv_ep *ep; + + nuke(&udc->eps[0], -ESHUTDOWN); + + list_for_each_entry(ep, &udc->gadget.ep_list, ep.ep_list) { + nuke(ep, -ESHUTDOWN); + } + + /* report disconnect; the driver is already quiesced */ + if (driver) { + spin_unlock(&udc->lock); + driver->disconnect(&udc->gadget); + spin_lock(&udc->lock); + } +} + +int usb_gadget_probe_driver(struct usb_gadget_driver *driver, + int (*bind)(struct usb_gadget *)) +{ + struct mv_udc *udc = the_controller; + int retval = 0; + unsigned long flags; + + if (!udc) + return -ENODEV; + + if (udc->driver) + return -EBUSY; + + spin_lock_irqsave(&udc->lock, flags); + + /* hook up the driver ... */ + driver->driver.bus = NULL; + udc->driver = driver; + udc->gadget.dev.driver = &driver->driver; + + udc->usb_state = USB_STATE_ATTACHED; + udc->ep0_state = WAIT_FOR_SETUP; + udc->ep0_dir = USB_DIR_OUT; + + spin_unlock_irqrestore(&udc->lock, flags); + + retval = bind(&udc->gadget); + if (retval) { + dev_err(&udc->dev->dev, "bind to driver %s --> %d\n", + driver->driver.name, retval); + udc->driver = NULL; + udc->gadget.dev.driver = NULL; + return retval; + } + udc_reset(udc); + ep0_reset(udc); + udc_start(udc); + + return 0; +} +EXPORT_SYMBOL(usb_gadget_probe_driver); + +int usb_gadget_unregister_driver(struct usb_gadget_driver *driver) +{ + struct mv_udc *udc = the_controller; + unsigned long flags; + + if (!udc) + return -ENODEV; + + udc_stop(udc); + + spin_lock_irqsave(&udc->lock, flags); + + /* stop all usb activities */ + udc->gadget.speed = USB_SPEED_UNKNOWN; + stop_activity(udc, driver); + spin_unlock_irqrestore(&udc->lock, flags); + + /* unbind gadget driver */ + driver->unbind(&udc->gadget); + udc->gadget.dev.driver = NULL; + udc->driver = NULL; + + return 0; +} +EXPORT_SYMBOL(usb_gadget_unregister_driver); + +static int +udc_prime_status(struct mv_udc *udc, u8 direction, u16 status, bool empty) +{ + int retval = 0; + struct mv_req *req; + struct mv_ep *ep; + + ep = &udc->eps[0]; + udc->ep0_dir = direction; + + req = udc->status_req; + + /* fill in the reqest structure */ + if (empty == false) { + *((u16 *) req->req.buf) = cpu_to_le16(status); + req->req.length = 2; + } else + req->req.length = 0; + + req->ep = ep; + req->req.status = -EINPROGRESS; + req->req.actual = 0; + req->req.complete = NULL; + req->dtd_count = 0; + + /* prime the data phase */ + if (!req_to_dtd(req)) + retval = queue_dtd(ep, req); + else{ /* no mem */ + retval = -ENOMEM; + goto out; + } + + if (retval) { + dev_err(&udc->dev->dev, "response error on GET_STATUS request\n"); + goto out; + } + + list_add_tail(&req->queue, &ep->queue); + + return 0; +out: + return retval; +} + +static void ch9setaddress(struct mv_udc *udc, struct usb_ctrlrequest *setup) +{ + udc->dev_addr = (u8)setup->wValue; + + /* update usb state */ + udc->usb_state = USB_STATE_ADDRESS; + + if (udc_prime_status(udc, EP_DIR_IN, 0, true)) + ep0_stall(udc); +} + +static void ch9getstatus(struct mv_udc *udc, u8 ep_num, + struct usb_ctrlrequest *setup) +{ + u16 status; + int retval; + + if ((setup->bRequestType & (USB_DIR_IN | USB_TYPE_MASK)) + != (USB_DIR_IN | USB_TYPE_STANDARD)) + return; + + if ((setup->bRequestType & USB_RECIP_MASK) == USB_RECIP_DEVICE) { + status = 1 << USB_DEVICE_SELF_POWERED; + status |= udc->remote_wakeup << USB_DEVICE_REMOTE_WAKEUP; + } else if ((setup->bRequestType & USB_RECIP_MASK) + == USB_RECIP_INTERFACE) { + /* get interface status */ + status = 0; + } else if ((setup->bRequestType & USB_RECIP_MASK) + == USB_RECIP_ENDPOINT) { + u8 ep_num, direction; + + ep_num = setup->wIndex & USB_ENDPOINT_NUMBER_MASK; + direction = (setup->wIndex & USB_ENDPOINT_DIR_MASK) + ? EP_DIR_IN : EP_DIR_OUT; + status = ep_is_stall(udc, ep_num, direction) + << USB_ENDPOINT_HALT; + } + + retval = udc_prime_status(udc, EP_DIR_IN, status, false); + if (retval) + ep0_stall(udc); +} + +static void ch9clearfeature(struct mv_udc *udc, struct usb_ctrlrequest *setup) +{ + u8 ep_num; + u8 direction; + struct mv_ep *ep; + + if ((setup->bRequestType & (USB_TYPE_MASK | USB_RECIP_MASK)) + == ((USB_TYPE_STANDARD | USB_RECIP_DEVICE))) { + switch (setup->wValue) { + case USB_DEVICE_REMOTE_WAKEUP: + udc->remote_wakeup = 0; + break; + case USB_DEVICE_TEST_MODE: + mv_udc_testmode(udc, 0, false); + break; + default: + goto out; + } + } else if ((setup->bRequestType & (USB_TYPE_MASK | USB_RECIP_MASK)) + == ((USB_TYPE_STANDARD | USB_RECIP_ENDPOINT))) { + switch (setup->wValue) { + case USB_ENDPOINT_HALT: + ep_num = setup->wIndex & USB_ENDPOINT_NUMBER_MASK; + direction = (setup->wIndex & USB_ENDPOINT_DIR_MASK) + ? EP_DIR_IN : EP_DIR_OUT; + if (setup->wValue != 0 || setup->wLength != 0 + || ep_num > udc->max_eps) + goto out; + ep = &udc->eps[ep_num * 2 + direction]; + if (ep->wedge == 1) + break; + spin_unlock(&udc->lock); + ep_set_stall(udc, ep_num, direction, 0); + spin_lock(&udc->lock); + break; + default: + goto out; + } + } else + goto out; + + if (udc_prime_status(udc, EP_DIR_IN, 0, true)) + ep0_stall(udc); + else + udc->ep0_state = DATA_STATE_XMIT; +out: + return; +} + +static void ch9setfeature(struct mv_udc *udc, struct usb_ctrlrequest *setup) +{ + u8 ep_num; + u8 direction; + + if ((setup->bRequestType & (USB_TYPE_MASK | USB_RECIP_MASK)) + == ((USB_TYPE_STANDARD | USB_RECIP_DEVICE))) { + switch (setup->wValue) { + case USB_DEVICE_REMOTE_WAKEUP: + udc->remote_wakeup = 1; + break; + case USB_DEVICE_TEST_MODE: + if (setup->wIndex & 0xFF + && udc->gadget.speed != USB_SPEED_HIGH) + goto out; + if (udc->usb_state == USB_STATE_CONFIGURED + || udc->usb_state == USB_STATE_ADDRESS + || udc->usb_state == USB_STATE_DEFAULT) + mv_udc_testmode(udc, + setup->wIndex & 0xFF00, true); + else + goto out; + break; + default: + goto out; + } + } else if ((setup->bRequestType & (USB_TYPE_MASK | USB_RECIP_MASK)) + == ((USB_TYPE_STANDARD | USB_RECIP_ENDPOINT))) { + switch (setup->wValue) { + case USB_ENDPOINT_HALT: + ep_num = setup->wIndex & USB_ENDPOINT_NUMBER_MASK; + direction = (setup->wIndex & USB_ENDPOINT_DIR_MASK) + ? EP_DIR_IN : EP_DIR_OUT; + if (setup->wValue != 0 || setup->wLength != 0 + || ep_num > udc->max_eps) + goto out; + spin_unlock(&udc->lock); + ep_set_stall(udc, ep_num, direction, 1); + spin_lock(&udc->lock); + break; + default: + goto out; + } + } else + goto out; + + if (udc_prime_status(udc, EP_DIR_IN, 0, true)) + ep0_stall(udc); +out: + return; +} + +static void handle_setup_packet(struct mv_udc *udc, u8 ep_num, + struct usb_ctrlrequest *setup) +{ + bool delegate = false; + + nuke(&udc->eps[ep_num * 2 + EP_DIR_OUT], -ESHUTDOWN); + + dev_dbg(&udc->dev->dev, "SETUP %02x.%02x v%04x i%04x l%04x\n", + setup->bRequestType, setup->bRequest, + setup->wValue, setup->wIndex, setup->wLength); + /* We process some stardard setup requests here */ + if ((setup->bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD) { + switch (setup->bRequest) { + case USB_REQ_GET_STATUS: + ch9getstatus(udc, ep_num, setup); + break; + + case USB_REQ_SET_ADDRESS: + ch9setaddress(udc, setup); + break; + + case USB_REQ_CLEAR_FEATURE: + ch9clearfeature(udc, setup); + break; + + case USB_REQ_SET_FEATURE: + ch9setfeature(udc, setup); + break; + + default: + delegate = true; + } + } else + delegate = true; + + /* delegate USB standard requests to the gadget driver */ + if (delegate == true) { + /* USB requests handled by gadget */ + if (setup->wLength) { + /* DATA phase from gadget, STATUS phase from udc */ + udc->ep0_dir = (setup->bRequestType & USB_DIR_IN) + ? EP_DIR_IN : EP_DIR_OUT; + spin_unlock(&udc->lock); + if (udc->driver->setup(&udc->gadget, + &udc->local_setup_buff) < 0) + ep0_stall(udc); + spin_lock(&udc->lock); + udc->ep0_state = (setup->bRequestType & USB_DIR_IN) + ? DATA_STATE_XMIT : DATA_STATE_RECV; + } else { + /* no DATA phase, IN STATUS phase from gadget */ + udc->ep0_dir = EP_DIR_IN; + spin_unlock(&udc->lock); + if (udc->driver->setup(&udc->gadget, + &udc->local_setup_buff) < 0) + ep0_stall(udc); + spin_lock(&udc->lock); + udc->ep0_state = WAIT_FOR_OUT_STATUS; + } + } +} + +/* complete DATA or STATUS phase of ep0 prime status phase if needed */ +static void ep0_req_complete(struct mv_udc *udc, + struct mv_ep *ep0, struct mv_req *req) +{ + u32 new_addr; + + if (udc->usb_state == USB_STATE_ADDRESS) { + /* set the new address */ + new_addr = (u32)udc->dev_addr; + writel(new_addr << USB_DEVICE_ADDRESS_BIT_SHIFT, + &udc->op_regs->deviceaddr); + } + + done(ep0, req, 0); + + switch (udc->ep0_state) { + case DATA_STATE_XMIT: + /* receive status phase */ + if (udc_prime_status(udc, EP_DIR_OUT, 0, true)) + ep0_stall(udc); + break; + case DATA_STATE_RECV: + /* send status phase */ + if (udc_prime_status(udc, EP_DIR_IN, 0 , true)) + ep0_stall(udc); + break; + case WAIT_FOR_OUT_STATUS: + udc->ep0_state = WAIT_FOR_SETUP; + break; + case WAIT_FOR_SETUP: + dev_err(&udc->dev->dev, "unexpect ep0 packets\n"); + break; + default: + ep0_stall(udc); + break; + } +} + +static void get_setup_data(struct mv_udc *udc, u8 ep_num, u8 *buffer_ptr) +{ + u32 temp; + struct mv_dqh *dqh; + + dqh = &udc->ep_dqh[ep_num * 2 + EP_DIR_OUT]; + + /* Clear bit in ENDPTSETUPSTAT */ + temp = readl(&udc->op_regs->epsetupstat); + writel(temp | (1 << ep_num), &udc->op_regs->epsetupstat); + + /* while a hazard exists when setup package arrives */ + do { + /* Set Setup Tripwire */ + temp = readl(&udc->op_regs->usbcmd); + writel(temp | USBCMD_SETUP_TRIPWIRE_SET, &udc->op_regs->usbcmd); + + /* Copy the setup packet to local buffer */ + memcpy(buffer_ptr, (u8 *) dqh->setup_buffer, 8); + } while (!(readl(&udc->op_regs->usbcmd) & USBCMD_SETUP_TRIPWIRE_SET)); + + /* Clear Setup Tripwire */ + temp = readl(&udc->op_regs->usbcmd); + writel(temp & ~USBCMD_SETUP_TRIPWIRE_SET, &udc->op_regs->usbcmd); +} + +static void irq_process_tr_complete(struct mv_udc *udc) +{ + u32 tmp, bit_pos; + int i, ep_num = 0, direction = 0; + struct mv_ep *curr_ep; + struct mv_req *curr_req, *temp_req; + int status; + + /* + * We use separate loops for ENDPTSETUPSTAT and ENDPTCOMPLETE + * because the setup packets are to be read ASAP + */ + + /* Process all Setup packet received interrupts */ + tmp = readl(&udc->op_regs->epsetupstat); + + if (tmp) { + for (i = 0; i < udc->max_eps; i++) { + if (tmp & (1 << i)) { + get_setup_data(udc, i, + (u8 *)(&udc->local_setup_buff)); + handle_setup_packet(udc, i, + &udc->local_setup_buff); + } + } + } + + /* Don't clear the endpoint setup status register here. + * It is cleared as a setup packet is read out of the buffer + */ + + /* Process non-setup transaction complete interrupts */ + tmp = readl(&udc->op_regs->epcomplete); + + if (!tmp) + return; + + writel(tmp, &udc->op_regs->epcomplete); + + for (i = 0; i < udc->max_eps * 2; i++) { + ep_num = i >> 1; + direction = i % 2; + + bit_pos = 1 << (ep_num + 16 * direction); + + if (!(bit_pos & tmp)) + continue; + + if (i == 1) + curr_ep = &udc->eps[0]; + else + curr_ep = &udc->eps[i]; + /* process the req queue until an uncomplete request */ + list_for_each_entry_safe(curr_req, temp_req, + &curr_ep->queue, queue) { + status = process_ep_req(udc, i, curr_req); + if (status) + break; + + /* write back status to req */ + curr_req->req.status = status; + + /* ep0 request completion */ + if (ep_num == 0) { + ep0_req_complete(udc, curr_ep, curr_req); + break; + } else { + done(curr_ep, curr_req, status); + } + } + } +} + +void irq_process_reset(struct mv_udc *udc) +{ + u32 tmp; + unsigned int loops; + + udc->ep0_dir = EP_DIR_OUT; + udc->ep0_state = WAIT_FOR_SETUP; + udc->remote_wakeup = 0; /* default to 0 on reset */ + + /* The address bits are past bit 25-31. Set the address */ + tmp = readl(&udc->op_regs->deviceaddr); + tmp &= ~(USB_DEVICE_ADDRESS_MASK); + writel(tmp, &udc->op_regs->deviceaddr); + + /* Clear all the setup token semaphores */ + tmp = readl(&udc->op_regs->epsetupstat); + writel(tmp, &udc->op_regs->epsetupstat); + + /* Clear all the endpoint complete status bits */ + tmp = readl(&udc->op_regs->epcomplete); + writel(tmp, &udc->op_regs->epcomplete); + + /* wait until all endptprime bits cleared */ + loops = LOOPS(PRIME_TIMEOUT); + while (readl(&udc->op_regs->epprime) & 0xFFFFFFFF) { + if (loops == 0) { + dev_err(&udc->dev->dev, + "Timeout for ENDPTPRIME = 0x%x\n", + readl(&udc->op_regs->epprime)); + break; + } + loops--; + udelay(LOOPS_USEC); + } + + /* Write 1s to the Flush register */ + writel((u32)~0, &udc->op_regs->epflush); + + if (readl(&udc->op_regs->portsc[0]) & PORTSCX_PORT_RESET) { + dev_info(&udc->dev->dev, "usb bus reset\n"); + udc->usb_state = USB_STATE_DEFAULT; + /* reset all the queues, stop all USB activities */ + stop_activity(udc, udc->driver); + } else { + dev_info(&udc->dev->dev, "USB reset portsc 0x%x\n", + readl(&udc->op_regs->portsc)); + + /* + * re-initialize + * controller reset + */ + udc_reset(udc); + + /* reset all the queues, stop all USB activities */ + stop_activity(udc, udc->driver); + + /* reset ep0 dQH and endptctrl */ + ep0_reset(udc); + + /* enable interrupt and set controller to run state */ + udc_start(udc); + + udc->usb_state = USB_STATE_ATTACHED; + } +} + +static void handle_bus_resume(struct mv_udc *udc) +{ + udc->usb_state = udc->resume_state; + udc->resume_state = 0; + + /* report resume to the driver */ + if (udc->driver) { + if (udc->driver->resume) { + spin_unlock(&udc->lock); + udc->driver->resume(&udc->gadget); + spin_lock(&udc->lock); + } + } +} + +static void irq_process_suspend(struct mv_udc *udc) +{ + udc->resume_state = udc->usb_state; + udc->usb_state = USB_STATE_SUSPENDED; + + if (udc->driver->suspend) { + spin_unlock(&udc->lock); + udc->driver->suspend(&udc->gadget); + spin_lock(&udc->lock); + } +} + +static void irq_process_port_change(struct mv_udc *udc) +{ + u32 portsc; + + portsc = readl(&udc->op_regs->portsc[0]); + if (!(portsc & PORTSCX_PORT_RESET)) { + /* Get the speed */ + u32 speed = portsc & PORTSCX_PORT_SPEED_MASK; + switch (speed) { + case PORTSCX_PORT_SPEED_HIGH: + udc->gadget.speed = USB_SPEED_HIGH; + break; + case PORTSCX_PORT_SPEED_FULL: + udc->gadget.speed = USB_SPEED_FULL; + break; + case PORTSCX_PORT_SPEED_LOW: + udc->gadget.speed = USB_SPEED_LOW; + break; + default: + udc->gadget.speed = USB_SPEED_UNKNOWN; + break; + } + } + + if (portsc & PORTSCX_PORT_SUSPEND) { + udc->resume_state = udc->usb_state; + udc->usb_state = USB_STATE_SUSPENDED; + if (udc->driver->suspend) { + spin_unlock(&udc->lock); + udc->driver->suspend(&udc->gadget); + spin_lock(&udc->lock); + } + } + + if (!(portsc & PORTSCX_PORT_SUSPEND) + && udc->usb_state == USB_STATE_SUSPENDED) { + handle_bus_resume(udc); + } + + if (!udc->resume_state) + udc->usb_state = USB_STATE_DEFAULT; +} + +static void irq_process_error(struct mv_udc *udc) +{ + /* Increment the error count */ + udc->errors++; +} + +static irqreturn_t mv_udc_irq(int irq, void *dev) +{ + struct mv_udc *udc = (struct mv_udc *)dev; + u32 status, intr; + + spin_lock(&udc->lock); + + status = readl(&udc->op_regs->usbsts); + intr = readl(&udc->op_regs->usbintr); + status &= intr; + + if (status == 0) { + spin_unlock(&udc->lock); + return IRQ_NONE; + } + + /* Clear all the interrupts occured */ + writel(status, &udc->op_regs->usbsts); + + if (status & USBSTS_ERR) + irq_process_error(udc); + + if (status & USBSTS_RESET) + irq_process_reset(udc); + + if (status & USBSTS_PORT_CHANGE) + irq_process_port_change(udc); + + if (status & USBSTS_INT) + irq_process_tr_complete(udc); + + if (status & USBSTS_SUSPEND) + irq_process_suspend(udc); + + spin_unlock(&udc->lock); + + return IRQ_HANDLED; +} + +/* release device structure */ +static void gadget_release(struct device *_dev) +{ + struct mv_udc *udc = the_controller; + + complete(udc->done); + kfree(udc); +} + +static int mv_udc_remove(struct platform_device *dev) +{ + struct mv_udc *udc = the_controller; + + DECLARE_COMPLETION(done); + + udc->done = &done; + + /* free memory allocated in probe */ + if (udc->dtd_pool) + dma_pool_destroy(udc->dtd_pool); + + if (udc->ep_dqh) + dma_free_coherent(&dev->dev, udc->ep_dqh_size, + udc->ep_dqh, udc->ep_dqh_dma); + + kfree(udc->eps); + + if (udc->irq) + free_irq(udc->irq, &dev->dev); + + if (udc->cap_regs) + iounmap(udc->cap_regs); + udc->cap_regs = NULL; + + if (udc->phy_regs) + iounmap((void *)udc->phy_regs); + udc->phy_regs = 0; + + if (udc->status_req) { + kfree(udc->status_req->req.buf); + kfree(udc->status_req); + } + + device_unregister(&udc->gadget.dev); + + /* free dev, wait for the release() finished */ + wait_for_completion(&done); + + the_controller = NULL; + + return 0; +} + +int mv_udc_probe(struct platform_device *dev) +{ + struct mv_udc *udc; + int retval = 0; + struct resource *r; + size_t size; + + udc = kzalloc(sizeof *udc, GFP_KERNEL); + if (udc == NULL) { + dev_err(&dev->dev, "failed to allocate memory for udc\n"); + retval = -ENOMEM; + goto error; + } + + spin_lock_init(&udc->lock); + + udc->dev = dev; + + udc->clk = clk_get(&dev->dev, "U2OCLK"); + if (IS_ERR(udc->clk)) { + retval = PTR_ERR(udc->clk); + goto error; + } + + r = platform_get_resource_byname(udc->dev, IORESOURCE_MEM, "u2o"); + if (r == NULL) { + dev_err(&dev->dev, "no I/O memory resource defined\n"); + retval = -ENODEV; + goto error; + } + + udc->cap_regs = (struct mv_cap_regs __iomem *) + ioremap(r->start, resource_size(r)); + if (udc->cap_regs == NULL) { + dev_err(&dev->dev, "failed to map I/O memory\n"); + retval = -EBUSY; + goto error; + } + + r = platform_get_resource_byname(udc->dev, IORESOURCE_MEM, "u2ophy"); + if (r == NULL) { + dev_err(&dev->dev, "no phy I/O memory resource defined\n"); + retval = -ENODEV; + goto error; + } + + udc->phy_regs = (unsigned int)ioremap(r->start, resource_size(r)); + if (udc->phy_regs == 0) { + dev_err(&dev->dev, "failed to map phy I/O memory\n"); + retval = -EBUSY; + goto error; + } + + /* we will acces controller register, so enable the clk */ + clk_enable(udc->clk); + retval = mv_udc_phy_init(udc->phy_regs); + if (retval) { + dev_err(&dev->dev, "phy initialization error %d\n", retval); + goto error; + } + + udc->op_regs = (struct mv_op_regs __iomem *)((u32)udc->cap_regs + + (readl(&udc->cap_regs->caplength_hciversion) + & CAPLENGTH_MASK)); + udc->max_eps = readl(&udc->cap_regs->dccparams) & DCCPARAMS_DEN_MASK; + + size = udc->max_eps * sizeof(struct mv_dqh) *2; + size = (size + DQH_ALIGNMENT - 1) & ~(DQH_ALIGNMENT - 1); + udc->ep_dqh = dma_alloc_coherent(&dev->dev, size, + &udc->ep_dqh_dma, GFP_KERNEL); + + if (udc->ep_dqh == NULL) { + dev_err(&dev->dev, "allocate dQH memory failed\n"); + retval = -ENOMEM; + goto error; + } + udc->ep_dqh_size = size; + + /* create dTD dma_pool resource */ + udc->dtd_pool = dma_pool_create("mv_dtd", + &dev->dev, + sizeof(struct mv_dtd), + DTD_ALIGNMENT, + DMA_BOUNDARY); + + if (!udc->dtd_pool) { + retval = -ENOMEM; + goto error; + } + + size = udc->max_eps * sizeof(struct mv_ep) *2; + udc->eps = kzalloc(size, GFP_KERNEL); + if (udc->eps == NULL) { + dev_err(&dev->dev, "allocate ep memory failed\n"); + retval = -ENOMEM; + goto error; + } + + /* initialize ep0 status request structure */ + udc->status_req = kzalloc(sizeof(struct mv_req), GFP_KERNEL); + if (!udc->status_req) { + dev_err(&dev->dev, "allocate status_req memory failed\n"); + retval = -ENOMEM; + goto error; + } + INIT_LIST_HEAD(&udc->status_req->queue); + + /* allocate a small amount of memory to get valid address */ + udc->status_req->req.buf = kzalloc(8, GFP_KERNEL); + udc->status_req->req.dma = virt_to_phys(udc->status_req->req.buf); + + udc->resume_state = USB_STATE_NOTATTACHED; + udc->usb_state = USB_STATE_POWERED; + udc->ep0_dir = EP_DIR_OUT; + udc->remote_wakeup = 0; + + r = platform_get_resource(udc->dev, IORESOURCE_IRQ, 0); + if (r == NULL) { + dev_err(&dev->dev, "no IRQ resource defined\n"); + retval = -ENODEV; + goto error; + } + udc->irq = r->start; + if (request_irq(udc->irq, mv_udc_irq, + IRQF_DISABLED | IRQF_SHARED, driver_name, udc)) { + dev_err(&dev->dev, "Request irq %d for UDC failed\n", + udc->irq); + retval = -ENODEV; + goto error; + } + + /* initialize gadget structure */ + udc->gadget.ops = &mv_ops; /* usb_gadget_ops */ + udc->gadget.ep0 = &udc->eps[0].ep; /* gadget ep0 */ + INIT_LIST_HEAD(&udc->gadget.ep_list); /* ep_list */ + udc->gadget.speed = USB_SPEED_UNKNOWN; /* speed */ + udc->gadget.is_dualspeed = 1; /* support dual speed */ + + /* the "gadget" abstracts/virtualizes the controller */ + dev_set_name(&udc->gadget.dev, "gadget"); + udc->gadget.dev.parent = &dev->dev; + udc->gadget.dev.dma_mask = dev->dev.dma_mask; + udc->gadget.dev.release = gadget_release; + udc->gadget.name = driver_name; /* gadget name */ + + retval = device_register(&udc->gadget.dev); + if (retval) + goto error; + + eps_init(udc); + + the_controller = udc; + + goto out; +error: + if (udc) + mv_udc_remove(udc->dev); +out: + return retval; +} + +#ifdef CONFIG_PM +static int mv_udc_suspend(struct platform_device *_dev, pm_message_t state) +{ + struct mv_udc *udc = the_controller; + + udc_stop(udc); + + return 0; +} + +static int mv_udc_resume(struct platform_device *_dev) +{ + struct mv_udc *udc = the_controller; + int retval; + + retval = mv_udc_phy_init(udc->phy_regs); + if (retval) { + dev_err(_dev, "phy initialization error %d\n", retval); + goto error; + } + udc_reset(udc); + ep0_reset(udc); + udc_start(udc); + + return 0; +} + +static const struct dev_pm_ops mv_udc_pm_ops = { + .suspend = mv_udc_suspend, + .resume = mv_udc_resume, +}; +#endif + +static struct platform_driver udc_driver = { + .probe = mv_udc_probe, + .remove = __exit_p(mv_udc_remove), + .driver = { + .owner = THIS_MODULE, + .name = "pxa-u2o", +#ifdef CONFIG_PM + .pm = mv_udc_pm_ops, +#endif + }, +}; + + +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_AUTHOR("Chao Xie <chao.xie@marvell.com>"); +MODULE_VERSION(DRIVER_VERSION); +MODULE_LICENSE("GPL"); + + +static int __init init(void) +{ + return platform_driver_register(&udc_driver); +} +module_init(init); + + +static void __exit cleanup(void) +{ + platform_driver_unregister(&udc_driver); +} +module_exit(cleanup); + diff --git a/drivers/usb/gadget/mv_udc_phy.c b/drivers/usb/gadget/mv_udc_phy.c new file mode 100644 index 000000000000..d4dea97e38a5 --- /dev/null +++ b/drivers/usb/gadget/mv_udc_phy.c @@ -0,0 +1,214 @@ +#include <linux/delay.h> +#include <linux/timer.h> +#include <linux/io.h> +#include <linux/errno.h> + +#include <mach/cputype.h> + +#ifdef CONFIG_ARCH_MMP + +#define UTMI_REVISION 0x0 +#define UTMI_CTRL 0x4 +#define UTMI_PLL 0x8 +#define UTMI_TX 0xc +#define UTMI_RX 0x10 +#define UTMI_IVREF 0x14 +#define UTMI_T0 0x18 +#define UTMI_T1 0x1c +#define UTMI_T2 0x20 +#define UTMI_T3 0x24 +#define UTMI_T4 0x28 +#define UTMI_T5 0x2c +#define UTMI_RESERVE 0x30 +#define UTMI_USB_INT 0x34 +#define UTMI_DBG_CTL 0x38 +#define UTMI_OTG_ADDON 0x3c + +/* For UTMICTRL Register */ +#define UTMI_CTRL_USB_CLK_EN (1 << 31) +/* pxa168 */ +#define UTMI_CTRL_SUSPEND_SET1 (1 << 30) +#define UTMI_CTRL_SUSPEND_SET2 (1 << 29) +#define UTMI_CTRL_RXBUF_PDWN (1 << 24) +#define UTMI_CTRL_TXBUF_PDWN (1 << 11) + +#define UTMI_CTRL_INPKT_DELAY_SHIFT 30 +#define UTMI_CTRL_INPKT_DELAY_SOF_SHIFT 28 +#define UTMI_CTRL_PU_REF_SHIFT 20 +#define UTMI_CTRL_ARC_PULLDN_SHIFT 12 +#define UTMI_CTRL_PLL_PWR_UP_SHIFT 1 +#define UTMI_CTRL_PWR_UP_SHIFT 0 +/* For UTMI_PLL Register */ +#define UTMI_PLL_CLK_BLK_EN_SHIFT 24 +#define UTMI_PLL_FBDIV_SHIFT 4 +#define UTMI_PLL_REFDIV_SHIFT 0 +#define UTMI_PLL_FBDIV_MASK 0x00000FF0 +#define UTMI_PLL_REFDIV_MASK 0x0000000F +#define UTMI_PLL_ICP_MASK 0x00007000 +#define UTMI_PLL_KVCO_MASK 0x00031000 +#define UTMI_PLL_PLLCALI12_SHIFT 29 +#define UTMI_PLL_PLLCALI12_MASK (0x3 << 29) +#define UTMI_PLL_PLLVDD18_SHIFT 27 +#define UTMI_PLL_PLLVDD18_MASK (0x3 << 27) +#define UTMI_PLL_PLLVDD12_SHIFT 25 +#define UTMI_PLL_PLLVDD12_MASK (0x3 << 25) +#define UTMI_PLL_KVCO_SHIFT 15 +#define UTMI_PLL_ICP_SHIFT 12 +/* For UTMI_TX Register */ +#define UTMI_TX_REG_EXT_FS_RCAL_SHIFT 27 +#define UTMI_TX_REG_EXT_FS_RCAL_MASK (0xf << 27) +#define UTMI_TX_REG_EXT_FS_RCAL_EN_MASK 26 +#define UTMI_TX_REG_EXT_FS_RCAL_EN (0x1 << 26) +#define UTMI_TX_LOW_VDD_EN_SHIFT 11 +#define UTMI_TX_IMPCAL_VTH_SHIFT 14 +#define UTMI_TX_IMPCAL_VTH_MASK (0x7 << 14) +#define UTMI_TX_CK60_PHSEL_SHIFT 17 +#define UTMI_TX_CK60_PHSEL_MASK (0xf << 17) +#define UTMI_TX_TXVDD12_SHIFT 22 +#define UTMI_TX_TXVDD12_MASK (0x3 << 22) +#define UTMI_TX_AMP_SHIFT 0 +#define UTMI_TX_AMP_MASK (0x7 << 0) +/* For UTMI_RX Register */ +#define UTMI_RX_SQ_THRESH_SHIFT 4 +#define UTMI_RX_SQ_THRESH_MASK (0xf << 4) +#define UTMI_REG_SQ_LENGTH_SHIFT 15 +#define UTMI_REG_SQ_LENGTH_MASK (0x3 << 15) + +#define REG_RCAL_START 0x00001000 +#define VCOCAL_START 0x00200000 +#define KVCO_EXT 0x00400000 +#define PLL_READY 0x00800000 +#define CLK_BLK_EN 0x01000000 +#endif + +static unsigned int u2o_read(unsigned int base, unsigned int offset) +{ + return readl(base + offset); +} + +static void u2o_set(unsigned int base, unsigned int offset, unsigned int value) +{ + unsigned int reg; + + reg = readl(base + offset); + reg |= value; + writel(reg, base + offset); + readl(base + offset); +} + +static void u2o_clear(unsigned int base, unsigned int offset, + unsigned int value) +{ + unsigned int reg; + + reg = readl(base + offset); + reg &= ~value; + writel(reg, base + offset); + readl(base + offset); +} + +static void u2o_write(unsigned int base, unsigned int offset, + unsigned int value) +{ + writel(value, base + offset); + readl(base + offset); +} + +#ifdef CONFIG_ARCH_MMP +int mv_udc_phy_init(unsigned int base) +{ + unsigned long timeout; + + /* Initialize the USB PHY power */ + if (cpu_is_pxa910()) { + u2o_set(base, UTMI_CTRL, (1 << UTMI_CTRL_INPKT_DELAY_SOF_SHIFT) + | (1 << UTMI_CTRL_PU_REF_SHIFT)); + } + + u2o_set(base, UTMI_CTRL, 1 << UTMI_CTRL_PLL_PWR_UP_SHIFT); + u2o_set(base, UTMI_CTRL, 1 << UTMI_CTRL_PWR_UP_SHIFT); + + /* UTMI_PLL settings */ + u2o_clear(base, UTMI_PLL, UTMI_PLL_PLLVDD18_MASK + | UTMI_PLL_PLLVDD12_MASK | UTMI_PLL_PLLCALI12_MASK + | UTMI_PLL_FBDIV_MASK | UTMI_PLL_REFDIV_MASK + | UTMI_PLL_ICP_MASK | UTMI_PLL_KVCO_MASK); + + u2o_set(base, UTMI_PLL, (0xee << UTMI_PLL_FBDIV_SHIFT) + | (0xb << UTMI_PLL_REFDIV_SHIFT) + | (3 << UTMI_PLL_PLLVDD18_SHIFT) + | (3 << UTMI_PLL_PLLVDD12_SHIFT) + | (3 << UTMI_PLL_PLLCALI12_SHIFT) + | (1 << UTMI_PLL_ICP_SHIFT) | (3 << UTMI_PLL_KVCO_SHIFT)); + + /* UTMI_TX */ + u2o_clear(base, UTMI_TX, UTMI_TX_REG_EXT_FS_RCAL_EN_MASK + | UTMI_TX_TXVDD12_MASK + | UTMI_TX_CK60_PHSEL_MASK | UTMI_TX_IMPCAL_VTH_MASK + | UTMI_TX_REG_EXT_FS_RCAL_MASK | UTMI_TX_AMP_MASK); + u2o_set(base, UTMI_TX, (3 << UTMI_TX_TXVDD12_SHIFT) + | (4 << UTMI_TX_CK60_PHSEL_SHIFT) + | (4 << UTMI_TX_IMPCAL_VTH_SHIFT) + | (8 << UTMI_TX_REG_EXT_FS_RCAL_SHIFT) + | (3 << UTMI_TX_AMP_SHIFT)); + + /* UTMI_RX */ + u2o_clear(base, UTMI_RX, UTMI_RX_SQ_THRESH_MASK + | UTMI_REG_SQ_LENGTH_MASK); + if (cpu_is_pxa168()) + u2o_set(base, UTMI_RX, (7 << UTMI_RX_SQ_THRESH_SHIFT) + | (2 << UTMI_REG_SQ_LENGTH_SHIFT)); + else + u2o_set(base, UTMI_RX, (0x7 << UTMI_RX_SQ_THRESH_SHIFT) + | (2 << UTMI_REG_SQ_LENGTH_SHIFT)); + + /* UTMI_IVREF */ + if (cpu_is_pxa168()) + /* + * fixing Microsoft Altair board interface with NEC hub issue - + * Set UTMI_IVREF from 0x4a3 to 0x4bf + */ + u2o_write(base, UTMI_IVREF, 0x4bf); + + /* calibrate */ + timeout = jiffies + 100; + while ((u2o_read(base, UTMI_PLL) & PLL_READY) == 0) { + if (time_after(jiffies, timeout)) + return -ETIME; + cpu_relax(); + } + + /* toggle VCOCAL_START bit of UTMI_PLL */ + udelay(200); + u2o_set(base, UTMI_PLL, VCOCAL_START); + udelay(40); + u2o_clear(base, UTMI_PLL, VCOCAL_START); + + /* toggle REG_RCAL_START bit of UTMI_TX */ + udelay(200); + u2o_set(base, UTMI_TX, REG_RCAL_START); + udelay(40); + u2o_clear(base, UTMI_TX, REG_RCAL_START); + udelay(200); + + /* make sure phy is ready */ + timeout = jiffies + 100; + while ((u2o_read(base, UTMI_PLL) & PLL_READY) == 0) { + if (time_after(jiffies, timeout)) + return -ETIME; + cpu_relax(); + } + + if (cpu_is_pxa168()) { + u2o_set(base, UTMI_RESERVE, 1 << 5); + /* Turn on UTMI PHY OTG extension */ + u2o_write(base, UTMI_OTG_ADDON, 1); + } + return 0; +} +#else +int mv_udc_phy_init(unsigned int base) +{ + return 0; +} +#endif diff --git a/drivers/usb/gadget/ncm.c b/drivers/usb/gadget/ncm.c new file mode 100644 index 000000000000..99c179ad729d --- /dev/null +++ b/drivers/usb/gadget/ncm.c @@ -0,0 +1,248 @@ +/* + * ncm.c -- NCM gadget driver + * + * Copyright (C) 2010 Nokia Corporation + * Contact: Yauheni Kaliuta <yauheni.kaliuta@nokia.com> + * + * The driver borrows from ether.c which is: + * + * Copyright (C) 2003-2005,2008 David Brownell + * Copyright (C) 2003-2004 Robert Schwebel, Benedikt Spranger + * Copyright (C) 2008 Nokia Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +/* #define DEBUG */ +/* #define VERBOSE_DEBUG */ + +#include <linux/kernel.h> +#include <linux/utsname.h> + + +#include "u_ether.h" + +#define DRIVER_DESC "NCM Gadget" + +/*-------------------------------------------------------------------------*/ + +/* + * Kbuild is not very cooperative with respect to linking separately + * compiled library objects into one module. So for now we won't use + * separate compilation ... ensuring init/exit sections work to shrink + * the runtime footprint, and giving us at least some parts of what + * a "gcc --combine ... part1.c part2.c part3.c ... " build would. + */ +#include "composite.c" +#include "usbstring.c" +#include "config.c" +#include "epautoconf.c" + +#include "f_ncm.c" +#include "u_ether.c" + +/*-------------------------------------------------------------------------*/ + +/* DO NOT REUSE THESE IDs with a protocol-incompatible driver!! Ever!! + * Instead: allocate your own, using normal USB-IF procedures. + */ + +/* Thanks to NetChip Technologies for donating this product ID. + * It's for devices with only CDC Ethernet configurations. + */ +#define CDC_VENDOR_NUM 0x0525 /* NetChip */ +#define CDC_PRODUCT_NUM 0xa4a1 /* Linux-USB Ethernet Gadget */ + +/*-------------------------------------------------------------------------*/ + +static struct usb_device_descriptor device_desc = { + .bLength = sizeof device_desc, + .bDescriptorType = USB_DT_DEVICE, + + .bcdUSB = cpu_to_le16 (0x0200), + + .bDeviceClass = USB_CLASS_COMM, + .bDeviceSubClass = 0, + .bDeviceProtocol = 0, + /* .bMaxPacketSize0 = f(hardware) */ + + /* Vendor and product id defaults change according to what configs + * we support. (As does bNumConfigurations.) These values can + * also be overridden by module parameters. + */ + .idVendor = cpu_to_le16 (CDC_VENDOR_NUM), + .idProduct = cpu_to_le16 (CDC_PRODUCT_NUM), + /* .bcdDevice = f(hardware) */ + /* .iManufacturer = DYNAMIC */ + /* .iProduct = DYNAMIC */ + /* NO SERIAL NUMBER */ + .bNumConfigurations = 1, +}; + +static struct usb_otg_descriptor otg_descriptor = { + .bLength = sizeof otg_descriptor, + .bDescriptorType = USB_DT_OTG, + + /* REVISIT SRP-only hardware is possible, although + * it would not be called "OTG" ... + */ + .bmAttributes = USB_OTG_SRP | USB_OTG_HNP, +}; + +static const struct usb_descriptor_header *otg_desc[] = { + (struct usb_descriptor_header *) &otg_descriptor, + NULL, +}; + + +/* string IDs are assigned dynamically */ + +#define STRING_MANUFACTURER_IDX 0 +#define STRING_PRODUCT_IDX 1 + +static char manufacturer[50]; + +static struct usb_string strings_dev[] = { + [STRING_MANUFACTURER_IDX].s = manufacturer, + [STRING_PRODUCT_IDX].s = DRIVER_DESC, + { } /* end of list */ +}; + +static struct usb_gadget_strings stringtab_dev = { + .language = 0x0409, /* en-us */ + .strings = strings_dev, +}; + +static struct usb_gadget_strings *dev_strings[] = { + &stringtab_dev, + NULL, +}; + +static u8 hostaddr[ETH_ALEN]; + +/*-------------------------------------------------------------------------*/ + +static int __init ncm_do_config(struct usb_configuration *c) +{ + /* FIXME alloc iConfiguration string, set it in c->strings */ + + if (gadget_is_otg(c->cdev->gadget)) { + c->descriptors = otg_desc; + c->bmAttributes |= USB_CONFIG_ATT_WAKEUP; + } + + return ncm_bind_config(c, hostaddr); +} + +static struct usb_configuration ncm_config_driver = { + /* .label = f(hardware) */ + .label = "CDC Ethernet (NCM)", + .bConfigurationValue = 1, + /* .iConfiguration = DYNAMIC */ + .bmAttributes = USB_CONFIG_ATT_SELFPOWER, +}; + +/*-------------------------------------------------------------------------*/ + +static int __init gncm_bind(struct usb_composite_dev *cdev) +{ + int gcnum; + struct usb_gadget *gadget = cdev->gadget; + int status; + + /* set up network link layer */ + status = gether_setup(cdev->gadget, hostaddr); + if (status < 0) + return status; + + gcnum = usb_gadget_controller_number(gadget); + if (gcnum >= 0) + device_desc.bcdDevice = cpu_to_le16(0x0300 | gcnum); + else { + /* We assume that can_support_ecm() tells the truth; + * but if the controller isn't recognized at all then + * that assumption is a bit more likely to be wrong. + */ + dev_warn(&gadget->dev, + "controller '%s' not recognized; trying %s\n", + gadget->name, + ncm_config_driver.label); + device_desc.bcdDevice = + cpu_to_le16(0x0300 | 0x0099); + } + + + /* Allocate string descriptor numbers ... note that string + * contents can be overridden by the composite_dev glue. + */ + + /* device descriptor strings: manufacturer, product */ + snprintf(manufacturer, sizeof manufacturer, "%s %s with %s", + init_utsname()->sysname, init_utsname()->release, + gadget->name); + status = usb_string_id(cdev); + if (status < 0) + goto fail; + strings_dev[STRING_MANUFACTURER_IDX].id = status; + device_desc.iManufacturer = status; + + status = usb_string_id(cdev); + if (status < 0) + goto fail; + strings_dev[STRING_PRODUCT_IDX].id = status; + device_desc.iProduct = status; + + status = usb_add_config(cdev, &ncm_config_driver, + ncm_do_config); + if (status < 0) + goto fail; + + dev_info(&gadget->dev, "%s\n", DRIVER_DESC); + + return 0; + +fail: + gether_cleanup(); + return status; +} + +static int __exit gncm_unbind(struct usb_composite_dev *cdev) +{ + gether_cleanup(); + return 0; +} + +static struct usb_composite_driver ncm_driver = { + .name = "g_ncm", + .dev = &device_desc, + .strings = dev_strings, + .unbind = __exit_p(gncm_unbind), +}; + +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_AUTHOR("Yauheni Kaliuta"); +MODULE_LICENSE("GPL"); + +static int __init init(void) +{ + return usb_composite_probe(&ncm_driver, gncm_bind); +} +module_init(init); + +static void __exit cleanup(void) +{ + usb_composite_unregister(&ncm_driver); +} +module_exit(cleanup); diff --git a/drivers/usb/gadget/pch_udc.c b/drivers/usb/gadget/pch_udc.c new file mode 100644 index 000000000000..0c8dd81dddca --- /dev/null +++ b/drivers/usb/gadget/pch_udc.c @@ -0,0 +1,2947 @@ +/* + * Copyright (C) 2010 OKI SEMICONDUCTOR CO., LTD. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA. + */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/delay.h> +#include <linux/errno.h> +#include <linux/list.h> +#include <linux/interrupt.h> +#include <linux/usb/ch9.h> +#include <linux/usb/gadget.h> + +/* Address offset of Registers */ +#define UDC_EP_REG_SHIFT 0x20 /* Offset to next EP */ + +#define UDC_EPCTL_ADDR 0x00 /* Endpoint control */ +#define UDC_EPSTS_ADDR 0x04 /* Endpoint status */ +#define UDC_BUFIN_FRAMENUM_ADDR 0x08 /* buffer size in / frame number out */ +#define UDC_BUFOUT_MAXPKT_ADDR 0x0C /* buffer size out / maxpkt in */ +#define UDC_SUBPTR_ADDR 0x10 /* setup buffer pointer */ +#define UDC_DESPTR_ADDR 0x14 /* Data descriptor pointer */ +#define UDC_CONFIRM_ADDR 0x18 /* Write/Read confirmation */ + +#define UDC_DEVCFG_ADDR 0x400 /* Device configuration */ +#define UDC_DEVCTL_ADDR 0x404 /* Device control */ +#define UDC_DEVSTS_ADDR 0x408 /* Device status */ +#define UDC_DEVIRQSTS_ADDR 0x40C /* Device irq status */ +#define UDC_DEVIRQMSK_ADDR 0x410 /* Device irq mask */ +#define UDC_EPIRQSTS_ADDR 0x414 /* Endpoint irq status */ +#define UDC_EPIRQMSK_ADDR 0x418 /* Endpoint irq mask */ +#define UDC_DEVLPM_ADDR 0x41C /* LPM control / status */ +#define UDC_CSR_BUSY_ADDR 0x4f0 /* UDC_CSR_BUSY Status register */ +#define UDC_SRST_ADDR 0x4fc /* SOFT RESET register */ +#define UDC_CSR_ADDR 0x500 /* USB_DEVICE endpoint register */ + +/* Endpoint control register */ +/* Bit position */ +#define UDC_EPCTL_MRXFLUSH (1 << 12) +#define UDC_EPCTL_RRDY (1 << 9) +#define UDC_EPCTL_CNAK (1 << 8) +#define UDC_EPCTL_SNAK (1 << 7) +#define UDC_EPCTL_NAK (1 << 6) +#define UDC_EPCTL_P (1 << 3) +#define UDC_EPCTL_F (1 << 1) +#define UDC_EPCTL_S (1 << 0) +#define UDC_EPCTL_ET_SHIFT 4 +/* Mask patern */ +#define UDC_EPCTL_ET_MASK 0x00000030 +/* Value for ET field */ +#define UDC_EPCTL_ET_CONTROL 0 +#define UDC_EPCTL_ET_ISO 1 +#define UDC_EPCTL_ET_BULK 2 +#define UDC_EPCTL_ET_INTERRUPT 3 + +/* Endpoint status register */ +/* Bit position */ +#define UDC_EPSTS_XFERDONE (1 << 27) +#define UDC_EPSTS_RSS (1 << 26) +#define UDC_EPSTS_RCS (1 << 25) +#define UDC_EPSTS_TXEMPTY (1 << 24) +#define UDC_EPSTS_TDC (1 << 10) +#define UDC_EPSTS_HE (1 << 9) +#define UDC_EPSTS_MRXFIFO_EMP (1 << 8) +#define UDC_EPSTS_BNA (1 << 7) +#define UDC_EPSTS_IN (1 << 6) +#define UDC_EPSTS_OUT_SHIFT 4 +/* Mask patern */ +#define UDC_EPSTS_OUT_MASK 0x00000030 +#define UDC_EPSTS_ALL_CLR_MASK 0x1F0006F0 +/* Value for OUT field */ +#define UDC_EPSTS_OUT_SETUP 2 +#define UDC_EPSTS_OUT_DATA 1 + +/* Device configuration register */ +/* Bit position */ +#define UDC_DEVCFG_CSR_PRG (1 << 17) +#define UDC_DEVCFG_SP (1 << 3) +/* SPD Valee */ +#define UDC_DEVCFG_SPD_HS 0x0 +#define UDC_DEVCFG_SPD_FS 0x1 +#define UDC_DEVCFG_SPD_LS 0x2 + +/* Device control register */ +/* Bit position */ +#define UDC_DEVCTL_THLEN_SHIFT 24 +#define UDC_DEVCTL_BRLEN_SHIFT 16 +#define UDC_DEVCTL_CSR_DONE (1 << 13) +#define UDC_DEVCTL_SD (1 << 10) +#define UDC_DEVCTL_MODE (1 << 9) +#define UDC_DEVCTL_BREN (1 << 8) +#define UDC_DEVCTL_THE (1 << 7) +#define UDC_DEVCTL_DU (1 << 4) +#define UDC_DEVCTL_TDE (1 << 3) +#define UDC_DEVCTL_RDE (1 << 2) +#define UDC_DEVCTL_RES (1 << 0) + +/* Device status register */ +/* Bit position */ +#define UDC_DEVSTS_TS_SHIFT 18 +#define UDC_DEVSTS_ENUM_SPEED_SHIFT 13 +#define UDC_DEVSTS_ALT_SHIFT 8 +#define UDC_DEVSTS_INTF_SHIFT 4 +#define UDC_DEVSTS_CFG_SHIFT 0 +/* Mask patern */ +#define UDC_DEVSTS_TS_MASK 0xfffc0000 +#define UDC_DEVSTS_ENUM_SPEED_MASK 0x00006000 +#define UDC_DEVSTS_ALT_MASK 0x00000f00 +#define UDC_DEVSTS_INTF_MASK 0x000000f0 +#define UDC_DEVSTS_CFG_MASK 0x0000000f +/* value for maximum speed for SPEED field */ +#define UDC_DEVSTS_ENUM_SPEED_FULL 1 +#define UDC_DEVSTS_ENUM_SPEED_HIGH 0 +#define UDC_DEVSTS_ENUM_SPEED_LOW 2 +#define UDC_DEVSTS_ENUM_SPEED_FULLX 3 + +/* Device irq register */ +/* Bit position */ +#define UDC_DEVINT_RWKP (1 << 7) +#define UDC_DEVINT_ENUM (1 << 6) +#define UDC_DEVINT_SOF (1 << 5) +#define UDC_DEVINT_US (1 << 4) +#define UDC_DEVINT_UR (1 << 3) +#define UDC_DEVINT_ES (1 << 2) +#define UDC_DEVINT_SI (1 << 1) +#define UDC_DEVINT_SC (1 << 0) +/* Mask patern */ +#define UDC_DEVINT_MSK 0x7f + +/* Endpoint irq register */ +/* Bit position */ +#define UDC_EPINT_IN_SHIFT 0 +#define UDC_EPINT_OUT_SHIFT 16 +#define UDC_EPINT_IN_EP0 (1 << 0) +#define UDC_EPINT_OUT_EP0 (1 << 16) +/* Mask patern */ +#define UDC_EPINT_MSK_DISABLE_ALL 0xffffffff + +/* UDC_CSR_BUSY Status register */ +/* Bit position */ +#define UDC_CSR_BUSY (1 << 0) + +/* SOFT RESET register */ +/* Bit position */ +#define UDC_PSRST (1 << 1) +#define UDC_SRST (1 << 0) + +/* USB_DEVICE endpoint register */ +/* Bit position */ +#define UDC_CSR_NE_NUM_SHIFT 0 +#define UDC_CSR_NE_DIR_SHIFT 4 +#define UDC_CSR_NE_TYPE_SHIFT 5 +#define UDC_CSR_NE_CFG_SHIFT 7 +#define UDC_CSR_NE_INTF_SHIFT 11 +#define UDC_CSR_NE_ALT_SHIFT 15 +#define UDC_CSR_NE_MAX_PKT_SHIFT 19 +/* Mask patern */ +#define UDC_CSR_NE_NUM_MASK 0x0000000f +#define UDC_CSR_NE_DIR_MASK 0x00000010 +#define UDC_CSR_NE_TYPE_MASK 0x00000060 +#define UDC_CSR_NE_CFG_MASK 0x00000780 +#define UDC_CSR_NE_INTF_MASK 0x00007800 +#define UDC_CSR_NE_ALT_MASK 0x00078000 +#define UDC_CSR_NE_MAX_PKT_MASK 0x3ff80000 + +#define PCH_UDC_CSR(ep) (UDC_CSR_ADDR + ep*4) +#define PCH_UDC_EPINT(in, num)\ + (1 << (num + (in ? UDC_EPINT_IN_SHIFT : UDC_EPINT_OUT_SHIFT))) + +/* Index of endpoint */ +#define UDC_EP0IN_IDX 0 +#define UDC_EP0OUT_IDX 1 +#define UDC_EPIN_IDX(ep) (ep * 2) +#define UDC_EPOUT_IDX(ep) (ep * 2 + 1) +#define PCH_UDC_EP0 0 +#define PCH_UDC_EP1 1 +#define PCH_UDC_EP2 2 +#define PCH_UDC_EP3 3 + +/* Number of endpoint */ +#define PCH_UDC_EP_NUM 32 /* Total number of EPs (16 IN,16 OUT) */ +#define PCH_UDC_USED_EP_NUM 4 /* EP number of EP's really used */ +/* Length Value */ +#define PCH_UDC_BRLEN 0x0F /* Burst length */ +#define PCH_UDC_THLEN 0x1F /* Threshold length */ +/* Value of EP Buffer Size */ +#define UDC_EP0IN_BUFF_SIZE 64 +#define UDC_EPIN_BUFF_SIZE 512 +#define UDC_EP0OUT_BUFF_SIZE 64 +#define UDC_EPOUT_BUFF_SIZE 512 +/* Value of EP maximum packet size */ +#define UDC_EP0IN_MAX_PKT_SIZE 64 +#define UDC_EP0OUT_MAX_PKT_SIZE 64 +#define UDC_BULK_MAX_PKT_SIZE 512 + +/* DMA */ +#define DMA_DIR_RX 1 /* DMA for data receive */ +#define DMA_DIR_TX 2 /* DMA for data transmit */ +#define DMA_ADDR_INVALID (~(dma_addr_t)0) +#define UDC_DMA_MAXPACKET 65536 /* maximum packet size for DMA */ + +/** + * struct pch_udc_data_dma_desc - Structure to hold DMA descriptor information + * for data + * @status: Status quadlet + * @reserved: Reserved + * @dataptr: Buffer descriptor + * @next: Next descriptor + */ +struct pch_udc_data_dma_desc { + u32 status; + u32 reserved; + u32 dataptr; + u32 next; +}; + +/** + * struct pch_udc_stp_dma_desc - Structure to hold DMA descriptor information + * for control data + * @status: Status + * @reserved: Reserved + * @data12: First setup word + * @data34: Second setup word + */ +struct pch_udc_stp_dma_desc { + u32 status; + u32 reserved; + struct usb_ctrlrequest request; +} __attribute((packed)); + +/* DMA status definitions */ +/* Buffer status */ +#define PCH_UDC_BUFF_STS 0xC0000000 +#define PCH_UDC_BS_HST_RDY 0x00000000 +#define PCH_UDC_BS_DMA_BSY 0x40000000 +#define PCH_UDC_BS_DMA_DONE 0x80000000 +#define PCH_UDC_BS_HST_BSY 0xC0000000 +/* Rx/Tx Status */ +#define PCH_UDC_RXTX_STS 0x30000000 +#define PCH_UDC_RTS_SUCC 0x00000000 +#define PCH_UDC_RTS_DESERR 0x10000000 +#define PCH_UDC_RTS_BUFERR 0x30000000 +/* Last Descriptor Indication */ +#define PCH_UDC_DMA_LAST 0x08000000 +/* Number of Rx/Tx Bytes Mask */ +#define PCH_UDC_RXTX_BYTES 0x0000ffff + +/** + * struct pch_udc_cfg_data - Structure to hold current configuration + * and interface information + * @cur_cfg: current configuration in use + * @cur_intf: current interface in use + * @cur_alt: current alt interface in use + */ +struct pch_udc_cfg_data { + u16 cur_cfg; + u16 cur_intf; + u16 cur_alt; +}; + +/** + * struct pch_udc_ep - Structure holding a PCH USB device Endpoint information + * @ep: embedded ep request + * @td_stp_phys: for setup request + * @td_data_phys: for data request + * @td_stp: for setup request + * @td_data: for data request + * @dev: reference to device struct + * @offset_addr: offset address of ep register + * @desc: for this ep + * @queue: queue for requests + * @num: endpoint number + * @in: endpoint is IN + * @halted: endpoint halted? + * @epsts: Endpoint status + */ +struct pch_udc_ep { + struct usb_ep ep; + dma_addr_t td_stp_phys; + dma_addr_t td_data_phys; + struct pch_udc_stp_dma_desc *td_stp; + struct pch_udc_data_dma_desc *td_data; + struct pch_udc_dev *dev; + unsigned long offset_addr; + const struct usb_endpoint_descriptor *desc; + struct list_head queue; + unsigned num:5, + in:1, + halted:1; + unsigned long epsts; +}; + +/** + * struct pch_udc_dev - Structure holding complete information + * of the PCH USB device + * @gadget: gadget driver data + * @driver: reference to gadget driver bound + * @pdev: reference to the PCI device + * @ep: array of endpoints + * @lock: protects all state + * @active: enabled the PCI device + * @stall: stall requested + * @prot_stall: protcol stall requested + * @irq_registered: irq registered with system + * @mem_region: device memory mapped + * @registered: driver regsitered with system + * @suspended: driver in suspended state + * @connected: gadget driver associated + * @set_cfg_not_acked: pending acknowledgement 4 setup + * @waiting_zlp_ack: pending acknowledgement 4 ZLP + * @data_requests: DMA pool for data requests + * @stp_requests: DMA pool for setup requests + * @dma_addr: DMA pool for received + * @ep0out_buf: Buffer for DMA + * @setup_data: Received setup data + * @phys_addr: of device memory + * @base_addr: for mapped device memory + * @irq: IRQ line for the device + * @cfg_data: current cfg, intf, and alt in use + */ +struct pch_udc_dev { + struct usb_gadget gadget; + struct usb_gadget_driver *driver; + struct pci_dev *pdev; + struct pch_udc_ep ep[PCH_UDC_EP_NUM]; + spinlock_t lock; /* protects all state */ + unsigned active:1, + stall:1, + prot_stall:1, + irq_registered:1, + mem_region:1, + registered:1, + suspended:1, + connected:1, + set_cfg_not_acked:1, + waiting_zlp_ack:1; + struct pci_pool *data_requests; + struct pci_pool *stp_requests; + dma_addr_t dma_addr; + unsigned long ep0out_buf[64]; + struct usb_ctrlrequest setup_data; + unsigned long phys_addr; + void __iomem *base_addr; + unsigned irq; + struct pch_udc_cfg_data cfg_data; +}; + +#define PCH_UDC_PCI_BAR 1 +#define PCI_DEVICE_ID_INTEL_EG20T_UDC 0x8808 + +static const char ep0_string[] = "ep0in"; +static DEFINE_SPINLOCK(udc_stall_spinlock); /* stall spin lock */ +struct pch_udc_dev *pch_udc; /* pointer to device object */ + +static int speed_fs; +module_param_named(speed_fs, speed_fs, bool, S_IRUGO); +MODULE_PARM_DESC(speed_fs, "true for Full speed operation"); + +/** + * struct pch_udc_request - Structure holding a PCH USB device request packet + * @req: embedded ep request + * @td_data_phys: phys. address + * @td_data: first dma desc. of chain + * @td_data_last: last dma desc. of chain + * @queue: associated queue + * @dma_going: DMA in progress for request + * @dma_mapped: DMA memory mapped for request + * @dma_done: DMA completed for request + * @chain_len: chain length + */ +struct pch_udc_request { + struct usb_request req; + dma_addr_t td_data_phys; + struct pch_udc_data_dma_desc *td_data; + struct pch_udc_data_dma_desc *td_data_last; + struct list_head queue; + unsigned dma_going:1, + dma_mapped:1, + dma_done:1; + unsigned chain_len; +}; + +static inline u32 pch_udc_readl(struct pch_udc_dev *dev, unsigned long reg) +{ + return ioread32(dev->base_addr + reg); +} + +static inline void pch_udc_writel(struct pch_udc_dev *dev, + unsigned long val, unsigned long reg) +{ + iowrite32(val, dev->base_addr + reg); +} + +static inline void pch_udc_bit_set(struct pch_udc_dev *dev, + unsigned long reg, + unsigned long bitmask) +{ + pch_udc_writel(dev, pch_udc_readl(dev, reg) | bitmask, reg); +} + +static inline void pch_udc_bit_clr(struct pch_udc_dev *dev, + unsigned long reg, + unsigned long bitmask) +{ + pch_udc_writel(dev, pch_udc_readl(dev, reg) & ~(bitmask), reg); +} + +static inline u32 pch_udc_ep_readl(struct pch_udc_ep *ep, unsigned long reg) +{ + return ioread32(ep->dev->base_addr + ep->offset_addr + reg); +} + +static inline void pch_udc_ep_writel(struct pch_udc_ep *ep, + unsigned long val, unsigned long reg) +{ + iowrite32(val, ep->dev->base_addr + ep->offset_addr + reg); +} + +static inline void pch_udc_ep_bit_set(struct pch_udc_ep *ep, + unsigned long reg, + unsigned long bitmask) +{ + pch_udc_ep_writel(ep, pch_udc_ep_readl(ep, reg) | bitmask, reg); +} + +static inline void pch_udc_ep_bit_clr(struct pch_udc_ep *ep, + unsigned long reg, + unsigned long bitmask) +{ + pch_udc_ep_writel(ep, pch_udc_ep_readl(ep, reg) & ~(bitmask), reg); +} + +/** + * pch_udc_csr_busy() - Wait till idle. + * @dev: Reference to pch_udc_dev structure + */ +static void pch_udc_csr_busy(struct pch_udc_dev *dev) +{ + unsigned int count = 200; + + /* Wait till idle */ + while ((pch_udc_readl(dev, UDC_CSR_BUSY_ADDR) & UDC_CSR_BUSY) + && --count) + cpu_relax(); + if (!count) + dev_err(&dev->pdev->dev, "%s: wait error\n", __func__); +} + +/** + * pch_udc_write_csr() - Write the command and status registers. + * @dev: Reference to pch_udc_dev structure + * @val: value to be written to CSR register + * @addr: address of CSR register + */ +static void pch_udc_write_csr(struct pch_udc_dev *dev, unsigned long val, + unsigned int ep) +{ + unsigned long reg = PCH_UDC_CSR(ep); + + pch_udc_csr_busy(dev); /* Wait till idle */ + pch_udc_writel(dev, val, reg); + pch_udc_csr_busy(dev); /* Wait till idle */ +} + +/** + * pch_udc_read_csr() - Read the command and status registers. + * @dev: Reference to pch_udc_dev structure + * @addr: address of CSR register + * + * Return codes: content of CSR register + */ +static u32 pch_udc_read_csr(struct pch_udc_dev *dev, unsigned int ep) +{ + unsigned long reg = PCH_UDC_CSR(ep); + + pch_udc_csr_busy(dev); /* Wait till idle */ + pch_udc_readl(dev, reg); /* Dummy read */ + pch_udc_csr_busy(dev); /* Wait till idle */ + return pch_udc_readl(dev, reg); +} + +/** + * pch_udc_rmt_wakeup() - Initiate for remote wakeup + * @dev: Reference to pch_udc_dev structure + */ +static inline void pch_udc_rmt_wakeup(struct pch_udc_dev *dev) +{ + pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_RES); + mdelay(1); + pch_udc_bit_clr(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_RES); +} + +/** + * pch_udc_get_frame() - Get the current frame from device status register + * @dev: Reference to pch_udc_dev structure + * Retern current frame + */ +static inline int pch_udc_get_frame(struct pch_udc_dev *dev) +{ + u32 frame = pch_udc_readl(dev, UDC_DEVSTS_ADDR); + return (frame & UDC_DEVSTS_TS_MASK) >> UDC_DEVSTS_TS_SHIFT; +} + +/** + * pch_udc_clear_selfpowered() - Clear the self power control + * @dev: Reference to pch_udc_regs structure + */ +static inline void pch_udc_clear_selfpowered(struct pch_udc_dev *dev) +{ + pch_udc_bit_clr(dev, UDC_DEVCFG_ADDR, UDC_DEVCFG_SP); +} + +/** + * pch_udc_set_selfpowered() - Set the self power control + * @dev: Reference to pch_udc_regs structure + */ +static inline void pch_udc_set_selfpowered(struct pch_udc_dev *dev) +{ + pch_udc_bit_set(dev, UDC_DEVCFG_ADDR, UDC_DEVCFG_SP); +} + +/** + * pch_udc_set_disconnect() - Set the disconnect status. + * @dev: Reference to pch_udc_regs structure + */ +static inline void pch_udc_set_disconnect(struct pch_udc_dev *dev) +{ + pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_SD); +} + +/** + * pch_udc_clear_disconnect() - Clear the disconnect status. + * @dev: Reference to pch_udc_regs structure + */ +static void pch_udc_clear_disconnect(struct pch_udc_dev *dev) +{ + /* Clear the disconnect */ + pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_RES); + pch_udc_bit_clr(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_SD); + mdelay(1); + /* Resume USB signalling */ + pch_udc_bit_clr(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_RES); +} + +/** + * pch_udc_vbus_session() - set or clearr the disconnect status. + * @dev: Reference to pch_udc_regs structure + * @is_active: Parameter specifying the action + * 0: indicating VBUS power is ending + * !0: indicating VBUS power is starting + */ +static inline void pch_udc_vbus_session(struct pch_udc_dev *dev, + int is_active) +{ + if (is_active) + pch_udc_clear_disconnect(dev); + else + pch_udc_set_disconnect(dev); +} + +/** + * pch_udc_ep_set_stall() - Set the stall of endpoint + * @ep: Reference to structure of type pch_udc_ep_regs + */ +static void pch_udc_ep_set_stall(struct pch_udc_ep *ep) +{ + if (ep->in) { + pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_F); + pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_S); + } else { + pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_S); + } +} + +/** + * pch_udc_ep_clear_stall() - Clear the stall of endpoint + * @ep: Reference to structure of type pch_udc_ep_regs + */ +static inline void pch_udc_ep_clear_stall(struct pch_udc_ep *ep) +{ + /* Clear the stall */ + pch_udc_ep_bit_clr(ep, UDC_EPCTL_ADDR, UDC_EPCTL_S); + /* Clear NAK by writing CNAK */ + pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_CNAK); +} + +/** + * pch_udc_ep_set_trfr_type() - Set the transfer type of endpoint + * @ep: Reference to structure of type pch_udc_ep_regs + * @type: Type of endpoint + */ +static inline void pch_udc_ep_set_trfr_type(struct pch_udc_ep *ep, + u8 type) +{ + pch_udc_ep_writel(ep, ((type << UDC_EPCTL_ET_SHIFT) & + UDC_EPCTL_ET_MASK), UDC_EPCTL_ADDR); +} + +/** + * pch_udc_ep_set_bufsz() - Set the maximum packet size for the endpoint + * @ep: Reference to structure of type pch_udc_ep_regs + * @buf_size: The buffer size + */ +static void pch_udc_ep_set_bufsz(struct pch_udc_ep *ep, + u32 buf_size, u32 ep_in) +{ + u32 data; + if (ep_in) { + data = pch_udc_ep_readl(ep, UDC_BUFIN_FRAMENUM_ADDR); + data = (data & 0xffff0000) | (buf_size & 0xffff); + pch_udc_ep_writel(ep, data, UDC_BUFIN_FRAMENUM_ADDR); + } else { + data = pch_udc_ep_readl(ep, UDC_BUFOUT_MAXPKT_ADDR); + data = (buf_size << 16) | (data & 0xffff); + pch_udc_ep_writel(ep, data, UDC_BUFOUT_MAXPKT_ADDR); + } +} + +/** + * pch_udc_ep_set_maxpkt() - Set the Max packet size for the endpoint + * @ep: Reference to structure of type pch_udc_ep_regs + * @pkt_size: The packet size + */ +static void pch_udc_ep_set_maxpkt(struct pch_udc_ep *ep, u32 pkt_size) +{ + u32 data = pch_udc_ep_readl(ep, UDC_BUFOUT_MAXPKT_ADDR); + data = (data & 0xffff0000) | (pkt_size & 0xffff); + pch_udc_ep_writel(ep, data, UDC_BUFOUT_MAXPKT_ADDR); +} + +/** + * pch_udc_ep_set_subptr() - Set the Setup buffer pointer for the endpoint + * @ep: Reference to structure of type pch_udc_ep_regs + * @addr: Address of the register + */ +static inline void pch_udc_ep_set_subptr(struct pch_udc_ep *ep, u32 addr) +{ + pch_udc_ep_writel(ep, addr, UDC_SUBPTR_ADDR); +} + +/** + * pch_udc_ep_set_ddptr() - Set the Data descriptor pointer for the endpoint + * @ep: Reference to structure of type pch_udc_ep_regs + * @addr: Address of the register + */ +static inline void pch_udc_ep_set_ddptr(struct pch_udc_ep *ep, u32 addr) +{ + pch_udc_ep_writel(ep, addr, UDC_DESPTR_ADDR); +} + +/** + * pch_udc_ep_set_pd() - Set the poll demand bit for the endpoint + * @ep: Reference to structure of type pch_udc_ep_regs + */ +static inline void pch_udc_ep_set_pd(struct pch_udc_ep *ep) +{ + pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_P); +} + +/** + * pch_udc_ep_set_rrdy() - Set the receive ready bit for the endpoint + * @ep: Reference to structure of type pch_udc_ep_regs + */ +static inline void pch_udc_ep_set_rrdy(struct pch_udc_ep *ep) +{ + pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_RRDY); +} + +/** + * pch_udc_ep_clear_rrdy() - Clear the receive ready bit for the endpoint + * @ep: Reference to structure of type pch_udc_ep_regs + */ +static inline void pch_udc_ep_clear_rrdy(struct pch_udc_ep *ep) +{ + pch_udc_ep_bit_clr(ep, UDC_EPCTL_ADDR, UDC_EPCTL_RRDY); +} + +/** + * pch_udc_set_dma() - Set the 'TDE' or RDE bit of device control + * register depending on the direction specified + * @dev: Reference to structure of type pch_udc_regs + * @dir: whether Tx or Rx + * DMA_DIR_RX: Receive + * DMA_DIR_TX: Transmit + */ +static inline void pch_udc_set_dma(struct pch_udc_dev *dev, int dir) +{ + if (dir == DMA_DIR_RX) + pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_RDE); + else if (dir == DMA_DIR_TX) + pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_TDE); +} + +/** + * pch_udc_clear_dma() - Clear the 'TDE' or RDE bit of device control + * register depending on the direction specified + * @dev: Reference to structure of type pch_udc_regs + * @dir: Whether Tx or Rx + * DMA_DIR_RX: Receive + * DMA_DIR_TX: Transmit + */ +static inline void pch_udc_clear_dma(struct pch_udc_dev *dev, int dir) +{ + if (dir == DMA_DIR_RX) + pch_udc_bit_clr(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_RDE); + else if (dir == DMA_DIR_TX) + pch_udc_bit_clr(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_TDE); +} + +/** + * pch_udc_set_csr_done() - Set the device control register + * CSR done field (bit 13) + * @dev: reference to structure of type pch_udc_regs + */ +static inline void pch_udc_set_csr_done(struct pch_udc_dev *dev) +{ + pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_CSR_DONE); +} + +/** + * pch_udc_disable_interrupts() - Disables the specified interrupts + * @dev: Reference to structure of type pch_udc_regs + * @mask: Mask to disable interrupts + */ +static inline void pch_udc_disable_interrupts(struct pch_udc_dev *dev, + u32 mask) +{ + pch_udc_bit_set(dev, UDC_DEVIRQMSK_ADDR, mask); +} + +/** + * pch_udc_enable_interrupts() - Enable the specified interrupts + * @dev: Reference to structure of type pch_udc_regs + * @mask: Mask to enable interrupts + */ +static inline void pch_udc_enable_interrupts(struct pch_udc_dev *dev, + u32 mask) +{ + pch_udc_bit_clr(dev, UDC_DEVIRQMSK_ADDR, mask); +} + +/** + * pch_udc_disable_ep_interrupts() - Disable endpoint interrupts + * @dev: Reference to structure of type pch_udc_regs + * @mask: Mask to disable interrupts + */ +static inline void pch_udc_disable_ep_interrupts(struct pch_udc_dev *dev, + u32 mask) +{ + pch_udc_bit_set(dev, UDC_EPIRQMSK_ADDR, mask); +} + +/** + * pch_udc_enable_ep_interrupts() - Enable endpoint interrupts + * @dev: Reference to structure of type pch_udc_regs + * @mask: Mask to enable interrupts + */ +static inline void pch_udc_enable_ep_interrupts(struct pch_udc_dev *dev, + u32 mask) +{ + pch_udc_bit_clr(dev, UDC_EPIRQMSK_ADDR, mask); +} + +/** + * pch_udc_read_device_interrupts() - Read the device interrupts + * @dev: Reference to structure of type pch_udc_regs + * Retern The device interrupts + */ +static inline u32 pch_udc_read_device_interrupts(struct pch_udc_dev *dev) +{ + return pch_udc_readl(dev, UDC_DEVIRQSTS_ADDR); +} + +/** + * pch_udc_write_device_interrupts() - Write device interrupts + * @dev: Reference to structure of type pch_udc_regs + * @val: The value to be written to interrupt register + */ +static inline void pch_udc_write_device_interrupts(struct pch_udc_dev *dev, + u32 val) +{ + pch_udc_writel(dev, val, UDC_DEVIRQSTS_ADDR); +} + +/** + * pch_udc_read_ep_interrupts() - Read the endpoint interrupts + * @dev: Reference to structure of type pch_udc_regs + * Retern The endpoint interrupt + */ +static inline u32 pch_udc_read_ep_interrupts(struct pch_udc_dev *dev) +{ + return pch_udc_readl(dev, UDC_EPIRQSTS_ADDR); +} + +/** + * pch_udc_write_ep_interrupts() - Clear endpoint interupts + * @dev: Reference to structure of type pch_udc_regs + * @val: The value to be written to interrupt register + */ +static inline void pch_udc_write_ep_interrupts(struct pch_udc_dev *dev, + u32 val) +{ + pch_udc_writel(dev, val, UDC_EPIRQSTS_ADDR); +} + +/** + * pch_udc_read_device_status() - Read the device status + * @dev: Reference to structure of type pch_udc_regs + * Retern The device status + */ +static inline u32 pch_udc_read_device_status(struct pch_udc_dev *dev) +{ + return pch_udc_readl(dev, UDC_DEVSTS_ADDR); +} + +/** + * pch_udc_read_ep_control() - Read the endpoint control + * @ep: Reference to structure of type pch_udc_ep_regs + * Retern The endpoint control register value + */ +static inline u32 pch_udc_read_ep_control(struct pch_udc_ep *ep) +{ + return pch_udc_ep_readl(ep, UDC_EPCTL_ADDR); +} + +/** + * pch_udc_clear_ep_control() - Clear the endpoint control register + * @ep: Reference to structure of type pch_udc_ep_regs + * Retern The endpoint control register value + */ +static inline void pch_udc_clear_ep_control(struct pch_udc_ep *ep) +{ + return pch_udc_ep_writel(ep, 0, UDC_EPCTL_ADDR); +} + +/** + * pch_udc_read_ep_status() - Read the endpoint status + * @ep: Reference to structure of type pch_udc_ep_regs + * Retern The endpoint status + */ +static inline u32 pch_udc_read_ep_status(struct pch_udc_ep *ep) +{ + return pch_udc_ep_readl(ep, UDC_EPSTS_ADDR); +} + +/** + * pch_udc_clear_ep_status() - Clear the endpoint status + * @ep: Reference to structure of type pch_udc_ep_regs + * @stat: Endpoint status + */ +static inline void pch_udc_clear_ep_status(struct pch_udc_ep *ep, + u32 stat) +{ + return pch_udc_ep_writel(ep, stat, UDC_EPSTS_ADDR); +} + +/** + * pch_udc_ep_set_nak() - Set the bit 7 (SNAK field) + * of the endpoint control register + * @ep: Reference to structure of type pch_udc_ep_regs + */ +static inline void pch_udc_ep_set_nak(struct pch_udc_ep *ep) +{ + pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_SNAK); +} + +/** + * pch_udc_ep_clear_nak() - Set the bit 8 (CNAK field) + * of the endpoint control register + * @ep: reference to structure of type pch_udc_ep_regs + */ +static void pch_udc_ep_clear_nak(struct pch_udc_ep *ep) +{ + unsigned int loopcnt = 0; + struct pch_udc_dev *dev = ep->dev; + + if (!(pch_udc_ep_readl(ep, UDC_EPCTL_ADDR) & UDC_EPCTL_NAK)) + return; + if (!ep->in) { + loopcnt = 10000; + while (!(pch_udc_read_ep_status(ep) & UDC_EPSTS_MRXFIFO_EMP) && + --loopcnt) + udelay(5); + if (!loopcnt) + dev_err(&dev->pdev->dev, "%s: RxFIFO not Empty\n", + __func__); + } + loopcnt = 10000; + while ((pch_udc_read_ep_control(ep) & UDC_EPCTL_NAK) && --loopcnt) { + pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_CNAK); + udelay(5); + } + if (!loopcnt) + dev_err(&dev->pdev->dev, "%s: Clear NAK not set for ep%d%s\n", + __func__, ep->num, (ep->in ? "in" : "out")); +} + +/** + * pch_udc_ep_fifo_flush() - Flush the endpoint fifo + * @ep: reference to structure of type pch_udc_ep_regs + * @dir: direction of endpoint + * 0: endpoint is OUT + * !0: endpoint is IN + */ +static void pch_udc_ep_fifo_flush(struct pch_udc_ep *ep, int dir) +{ + unsigned int loopcnt = 0; + struct pch_udc_dev *dev = ep->dev; + + if (dir) { /* IN ep */ + pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_F); + return; + } + + if (pch_udc_read_ep_status(ep) & UDC_EPSTS_MRXFIFO_EMP) + return; + pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_MRXFLUSH); + /* Wait for RxFIFO Empty */ + loopcnt = 10000; + while (!(pch_udc_read_ep_status(ep) & UDC_EPSTS_MRXFIFO_EMP) && + --loopcnt) + udelay(5); + if (!loopcnt) + dev_err(&dev->pdev->dev, "RxFIFO not Empty\n"); + pch_udc_ep_bit_clr(ep, UDC_EPCTL_ADDR, UDC_EPCTL_MRXFLUSH); +} + +/** + * pch_udc_ep_enable() - This api enables endpoint + * @regs: Reference to structure pch_udc_ep_regs + * @desc: endpoint descriptor + */ +static void pch_udc_ep_enable(struct pch_udc_ep *ep, + struct pch_udc_cfg_data *cfg, + const struct usb_endpoint_descriptor *desc) +{ + u32 val = 0; + u32 buff_size = 0; + + pch_udc_ep_set_trfr_type(ep, desc->bmAttributes); + if (ep->in) + buff_size = UDC_EPIN_BUFF_SIZE; + else + buff_size = UDC_EPOUT_BUFF_SIZE; + pch_udc_ep_set_bufsz(ep, buff_size, ep->in); + pch_udc_ep_set_maxpkt(ep, le16_to_cpu(desc->wMaxPacketSize)); + pch_udc_ep_set_nak(ep); + pch_udc_ep_fifo_flush(ep, ep->in); + /* Configure the endpoint */ + val = ep->num << UDC_CSR_NE_NUM_SHIFT | ep->in << UDC_CSR_NE_DIR_SHIFT | + ((desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) << + UDC_CSR_NE_TYPE_SHIFT) | + (cfg->cur_cfg << UDC_CSR_NE_CFG_SHIFT) | + (cfg->cur_intf << UDC_CSR_NE_INTF_SHIFT) | + (cfg->cur_alt << UDC_CSR_NE_ALT_SHIFT) | + le16_to_cpu(desc->wMaxPacketSize) << UDC_CSR_NE_MAX_PKT_SHIFT; + + if (ep->in) + pch_udc_write_csr(ep->dev, val, UDC_EPIN_IDX(ep->num)); + else + pch_udc_write_csr(ep->dev, val, UDC_EPOUT_IDX(ep->num)); +} + +/** + * pch_udc_ep_disable() - This api disables endpoint + * @regs: Reference to structure pch_udc_ep_regs + */ +static void pch_udc_ep_disable(struct pch_udc_ep *ep) +{ + if (ep->in) { + /* flush the fifo */ + pch_udc_ep_writel(ep, UDC_EPCTL_F, UDC_EPCTL_ADDR); + /* set NAK */ + pch_udc_ep_writel(ep, UDC_EPCTL_SNAK, UDC_EPCTL_ADDR); + pch_udc_ep_bit_set(ep, UDC_EPSTS_ADDR, UDC_EPSTS_IN); + } else { + /* set NAK */ + pch_udc_ep_writel(ep, UDC_EPCTL_SNAK, UDC_EPCTL_ADDR); + } + /* reset desc pointer */ + pch_udc_ep_writel(ep, 0, UDC_DESPTR_ADDR); +} + +/** + * pch_udc_wait_ep_stall() - Wait EP stall. + * @dev: Reference to pch_udc_dev structure + */ +static void pch_udc_wait_ep_stall(struct pch_udc_ep *ep) +{ + unsigned int count = 10000; + + /* Wait till idle */ + while ((pch_udc_read_ep_control(ep) & UDC_EPCTL_S) && --count) + udelay(5); + if (!count) + dev_err(&ep->dev->pdev->dev, "%s: wait error\n", __func__); +} + +/** + * pch_udc_init() - This API initializes usb device controller + * @dev: Rreference to pch_udc_regs structure + */ +static void pch_udc_init(struct pch_udc_dev *dev) +{ + if (NULL == dev) { + pr_err("%s: Invalid address\n", __func__); + return; + } + /* Soft Reset and Reset PHY */ + pch_udc_writel(dev, UDC_SRST, UDC_SRST_ADDR); + pch_udc_writel(dev, UDC_SRST | UDC_PSRST, UDC_SRST_ADDR); + mdelay(1); + pch_udc_writel(dev, UDC_SRST, UDC_SRST_ADDR); + pch_udc_writel(dev, 0x00, UDC_SRST_ADDR); + mdelay(1); + /* mask and clear all device interrupts */ + pch_udc_bit_set(dev, UDC_DEVIRQMSK_ADDR, UDC_DEVINT_MSK); + pch_udc_bit_set(dev, UDC_DEVIRQSTS_ADDR, UDC_DEVINT_MSK); + + /* mask and clear all ep interrupts */ + pch_udc_bit_set(dev, UDC_EPIRQMSK_ADDR, UDC_EPINT_MSK_DISABLE_ALL); + pch_udc_bit_set(dev, UDC_EPIRQSTS_ADDR, UDC_EPINT_MSK_DISABLE_ALL); + + /* enable dynamic CSR programmingi, self powered and device speed */ + if (speed_fs) + pch_udc_bit_set(dev, UDC_DEVCFG_ADDR, UDC_DEVCFG_CSR_PRG | + UDC_DEVCFG_SP | UDC_DEVCFG_SPD_FS); + else /* defaul high speed */ + pch_udc_bit_set(dev, UDC_DEVCFG_ADDR, UDC_DEVCFG_CSR_PRG | + UDC_DEVCFG_SP | UDC_DEVCFG_SPD_HS); + pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, + (PCH_UDC_THLEN << UDC_DEVCTL_THLEN_SHIFT) | + (PCH_UDC_BRLEN << UDC_DEVCTL_BRLEN_SHIFT) | + UDC_DEVCTL_MODE | UDC_DEVCTL_BREN | + UDC_DEVCTL_THE); +} + +/** + * pch_udc_exit() - This API exit usb device controller + * @dev: Reference to pch_udc_regs structure + */ +static void pch_udc_exit(struct pch_udc_dev *dev) +{ + /* mask all device interrupts */ + pch_udc_bit_set(dev, UDC_DEVIRQMSK_ADDR, UDC_DEVINT_MSK); + /* mask all ep interrupts */ + pch_udc_bit_set(dev, UDC_EPIRQMSK_ADDR, UDC_EPINT_MSK_DISABLE_ALL); + /* put device in disconnected state */ + pch_udc_set_disconnect(dev); +} + +/** + * pch_udc_pcd_get_frame() - This API is invoked to get the current frame number + * @gadget: Reference to the gadget driver + * + * Return codes: + * 0: Success + * -EINVAL: If the gadget passed is NULL + */ +static int pch_udc_pcd_get_frame(struct usb_gadget *gadget) +{ + struct pch_udc_dev *dev; + + if (!gadget) + return -EINVAL; + dev = container_of(gadget, struct pch_udc_dev, gadget); + return pch_udc_get_frame(dev); +} + +/** + * pch_udc_pcd_wakeup() - This API is invoked to initiate a remote wakeup + * @gadget: Reference to the gadget driver + * + * Return codes: + * 0: Success + * -EINVAL: If the gadget passed is NULL + */ +static int pch_udc_pcd_wakeup(struct usb_gadget *gadget) +{ + struct pch_udc_dev *dev; + unsigned long flags; + + if (!gadget) + return -EINVAL; + dev = container_of(gadget, struct pch_udc_dev, gadget); + spin_lock_irqsave(&dev->lock, flags); + pch_udc_rmt_wakeup(dev); + spin_unlock_irqrestore(&dev->lock, flags); + return 0; +} + +/** + * pch_udc_pcd_selfpowered() - This API is invoked to specify whether the device + * is self powered or not + * @gadget: Reference to the gadget driver + * @value: Specifies self powered or not + * + * Return codes: + * 0: Success + * -EINVAL: If the gadget passed is NULL + */ +static int pch_udc_pcd_selfpowered(struct usb_gadget *gadget, int value) +{ + struct pch_udc_dev *dev; + + if (!gadget) + return -EINVAL; + dev = container_of(gadget, struct pch_udc_dev, gadget); + if (value) + pch_udc_set_selfpowered(dev); + else + pch_udc_clear_selfpowered(dev); + return 0; +} + +/** + * pch_udc_pcd_pullup() - This API is invoked to make the device + * visible/invisible to the host + * @gadget: Reference to the gadget driver + * @is_on: Specifies whether the pull up is made active or inactive + * + * Return codes: + * 0: Success + * -EINVAL: If the gadget passed is NULL + */ +static int pch_udc_pcd_pullup(struct usb_gadget *gadget, int is_on) +{ + struct pch_udc_dev *dev; + + if (!gadget) + return -EINVAL; + dev = container_of(gadget, struct pch_udc_dev, gadget); + pch_udc_vbus_session(dev, is_on); + return 0; +} + +/** + * pch_udc_pcd_vbus_session() - This API is used by a driver for an external + * transceiver (or GPIO) that + * detects a VBUS power session starting/ending + * @gadget: Reference to the gadget driver + * @is_active: specifies whether the session is starting or ending + * + * Return codes: + * 0: Success + * -EINVAL: If the gadget passed is NULL + */ +static int pch_udc_pcd_vbus_session(struct usb_gadget *gadget, int is_active) +{ + struct pch_udc_dev *dev; + + if (!gadget) + return -EINVAL; + dev = container_of(gadget, struct pch_udc_dev, gadget); + pch_udc_vbus_session(dev, is_active); + return 0; +} + +/** + * pch_udc_pcd_vbus_draw() - This API is used by gadget drivers during + * SET_CONFIGURATION calls to + * specify how much power the device can consume + * @gadget: Reference to the gadget driver + * @mA: specifies the current limit in 2mA unit + * + * Return codes: + * -EINVAL: If the gadget passed is NULL + * -EOPNOTSUPP: + */ +static int pch_udc_pcd_vbus_draw(struct usb_gadget *gadget, unsigned int mA) +{ + return -EOPNOTSUPP; +} + +static const struct usb_gadget_ops pch_udc_ops = { + .get_frame = pch_udc_pcd_get_frame, + .wakeup = pch_udc_pcd_wakeup, + .set_selfpowered = pch_udc_pcd_selfpowered, + .pullup = pch_udc_pcd_pullup, + .vbus_session = pch_udc_pcd_vbus_session, + .vbus_draw = pch_udc_pcd_vbus_draw, +}; + +/** + * complete_req() - This API is invoked from the driver when processing + * of a request is complete + * @ep: Reference to the endpoint structure + * @req: Reference to the request structure + * @status: Indicates the success/failure of completion + */ +static void complete_req(struct pch_udc_ep *ep, struct pch_udc_request *req, + int status) +{ + struct pch_udc_dev *dev; + unsigned halted = ep->halted; + + list_del_init(&req->queue); + + /* set new status if pending */ + if (req->req.status == -EINPROGRESS) + req->req.status = status; + else + status = req->req.status; + + dev = ep->dev; + if (req->dma_mapped) { + if (ep->in) + pci_unmap_single(dev->pdev, req->req.dma, + req->req.length, PCI_DMA_TODEVICE); + else + pci_unmap_single(dev->pdev, req->req.dma, + req->req.length, PCI_DMA_FROMDEVICE); + req->dma_mapped = 0; + req->req.dma = DMA_ADDR_INVALID; + } + ep->halted = 1; + spin_unlock(&dev->lock); + if (!ep->in) + pch_udc_ep_clear_rrdy(ep); + req->req.complete(&ep->ep, &req->req); + spin_lock(&dev->lock); + ep->halted = halted; +} + +/** + * empty_req_queue() - This API empties the request queue of an endpoint + * @ep: Reference to the endpoint structure + */ +static void empty_req_queue(struct pch_udc_ep *ep) +{ + struct pch_udc_request *req; + + ep->halted = 1; + while (!list_empty(&ep->queue)) { + req = list_entry(ep->queue.next, struct pch_udc_request, queue); + complete_req(ep, req, -ESHUTDOWN); /* Remove from list */ + } +} + +/** + * pch_udc_free_dma_chain() - This function frees the DMA chain created + * for the request + * @dev Reference to the driver structure + * @req Reference to the request to be freed + * + * Return codes: + * 0: Success + */ +static void pch_udc_free_dma_chain(struct pch_udc_dev *dev, + struct pch_udc_request *req) +{ + struct pch_udc_data_dma_desc *td = req->td_data; + unsigned i = req->chain_len; + + for (; i > 1; --i) { + dma_addr_t addr = (dma_addr_t)td->next; + /* do not free first desc., will be done by free for request */ + td = phys_to_virt(addr); + pci_pool_free(dev->data_requests, td, addr); + } +} + +/** + * pch_udc_create_dma_chain() - This function creates or reinitializes + * a DMA chain + * @ep: Reference to the endpoint structure + * @req: Reference to the request + * @buf_len: The buffer length + * @gfp_flags: Flags to be used while mapping the data buffer + * + * Return codes: + * 0: success, + * -ENOMEM: pci_pool_alloc invocation fails + */ +static int pch_udc_create_dma_chain(struct pch_udc_ep *ep, + struct pch_udc_request *req, + unsigned long buf_len, + gfp_t gfp_flags) +{ + struct pch_udc_data_dma_desc *td = req->td_data, *last; + unsigned long bytes = req->req.length, i = 0; + dma_addr_t dma_addr; + unsigned len = 1; + + if (req->chain_len > 1) + pch_udc_free_dma_chain(ep->dev, req); + + for (; ; bytes -= buf_len, ++len) { + if (ep->in) + td->status = PCH_UDC_BS_HST_BSY | min(buf_len, bytes); + else + td->status = PCH_UDC_BS_HST_BSY; + + if (bytes <= buf_len) + break; + + last = td; + td = pci_pool_alloc(ep->dev->data_requests, gfp_flags, + &dma_addr); + if (!td) + goto nomem; + + i += buf_len; + td->dataptr = req->req.dma + i; + last->next = dma_addr; + } + + req->td_data_last = td; + td->status |= PCH_UDC_DMA_LAST; + td->next = req->td_data_phys; + req->chain_len = len; + return 0; + +nomem: + if (len > 1) { + req->chain_len = len; + pch_udc_free_dma_chain(ep->dev, req); + } + req->chain_len = 1; + return -ENOMEM; +} + +/** + * prepare_dma() - This function creates and initializes the DMA chain + * for the request + * @ep: Reference to the endpoint structure + * @req: Reference to the request + * @gfp: Flag to be used while mapping the data buffer + * + * Return codes: + * 0: Success + * Other 0: linux error number on failure + */ +static int prepare_dma(struct pch_udc_ep *ep, struct pch_udc_request *req, + gfp_t gfp) +{ + int retval; + + req->td_data->dataptr = req->req.dma; + req->td_data->status |= PCH_UDC_DMA_LAST; + /* Allocate and create a DMA chain */ + retval = pch_udc_create_dma_chain(ep, req, ep->ep.maxpacket, gfp); + if (retval) { + pr_err("%s: could not create DMA chain: %d\n", + __func__, retval); + return retval; + } + if (!ep->in) + return 0; + if (req->req.length <= ep->ep.maxpacket) + req->td_data->status = PCH_UDC_DMA_LAST | PCH_UDC_BS_HST_BSY | + req->req.length; + /* if bytes < max packet then tx bytes must + * be written in packet per buffer mode + */ + if ((req->req.length < ep->ep.maxpacket) || !ep->num) + req->td_data->status = (req->td_data->status & + ~PCH_UDC_RXTX_BYTES) | req->req.length; + req->td_data->status = (req->td_data->status & + ~PCH_UDC_BUFF_STS) | PCH_UDC_BS_HST_BSY; + return 0; +} + +/** + * process_zlp() - This function process zero length packets + * from the gadget driver + * @ep: Reference to the endpoint structure + * @req: Reference to the request + */ +static void process_zlp(struct pch_udc_ep *ep, struct pch_udc_request *req) +{ + struct pch_udc_dev *dev = ep->dev; + + /* IN zlp's are handled by hardware */ + complete_req(ep, req, 0); + + /* if set_config or set_intf is waiting for ack by zlp + * then set CSR_DONE + */ + if (dev->set_cfg_not_acked) { + pch_udc_set_csr_done(dev); + dev->set_cfg_not_acked = 0; + } + /* setup command is ACK'ed now by zlp */ + if (!dev->stall && dev->waiting_zlp_ack) { + pch_udc_ep_clear_nak(&(dev->ep[UDC_EP0IN_IDX])); + dev->waiting_zlp_ack = 0; + } +} + +/** + * pch_udc_start_rxrequest() - This function starts the receive requirement. + * @ep: Reference to the endpoint structure + * @req: Reference to the request structure + */ +static void pch_udc_start_rxrequest(struct pch_udc_ep *ep, + struct pch_udc_request *req) +{ + struct pch_udc_data_dma_desc *td_data; + + pch_udc_clear_dma(ep->dev, DMA_DIR_RX); + td_data = req->td_data; + ep->td_data = req->td_data; + /* Set the status bits for all descriptors */ + while (1) { + td_data->status = (td_data->status & ~PCH_UDC_BUFF_STS) | + PCH_UDC_BS_HST_RDY; + if ((td_data->status & PCH_UDC_DMA_LAST) == PCH_UDC_DMA_LAST) + break; + td_data = phys_to_virt(td_data->next); + } + /* Write the descriptor pointer */ + pch_udc_ep_set_ddptr(ep, req->td_data_phys); + req->dma_going = 1; + pch_udc_enable_ep_interrupts(ep->dev, UDC_EPINT_OUT_EP0 << ep->num); + pch_udc_set_dma(ep->dev, DMA_DIR_RX); + pch_udc_ep_clear_nak(ep); + pch_udc_ep_set_rrdy(ep); +} + +/** + * pch_udc_pcd_ep_enable() - This API enables the endpoint. It is called + * from gadget driver + * @usbep: Reference to the USB endpoint structure + * @desc: Reference to the USB endpoint descriptor structure + * + * Return codes: + * 0: Success + * -EINVAL: + * -ESHUTDOWN: + */ +static int pch_udc_pcd_ep_enable(struct usb_ep *usbep, + const struct usb_endpoint_descriptor *desc) +{ + struct pch_udc_ep *ep; + struct pch_udc_dev *dev; + unsigned long iflags; + + if (!usbep || (usbep->name == ep0_string) || !desc || + (desc->bDescriptorType != USB_DT_ENDPOINT) || !desc->wMaxPacketSize) + return -EINVAL; + + ep = container_of(usbep, struct pch_udc_ep, ep); + dev = ep->dev; + if (!dev->driver || (dev->gadget.speed == USB_SPEED_UNKNOWN)) + return -ESHUTDOWN; + spin_lock_irqsave(&dev->lock, iflags); + ep->desc = desc; + ep->halted = 0; + pch_udc_ep_enable(ep, &ep->dev->cfg_data, desc); + ep->ep.maxpacket = le16_to_cpu(desc->wMaxPacketSize); + pch_udc_enable_ep_interrupts(ep->dev, PCH_UDC_EPINT(ep->in, ep->num)); + spin_unlock_irqrestore(&dev->lock, iflags); + return 0; +} + +/** + * pch_udc_pcd_ep_disable() - This API disables endpoint and is called + * from gadget driver + * @usbep Reference to the USB endpoint structure + * + * Return codes: + * 0: Success + * -EINVAL: + */ +static int pch_udc_pcd_ep_disable(struct usb_ep *usbep) +{ + struct pch_udc_ep *ep; + struct pch_udc_dev *dev; + unsigned long iflags; + + if (!usbep) + return -EINVAL; + + ep = container_of(usbep, struct pch_udc_ep, ep); + dev = ep->dev; + if ((usbep->name == ep0_string) || !ep->desc) + return -EINVAL; + + spin_lock_irqsave(&ep->dev->lock, iflags); + empty_req_queue(ep); + ep->halted = 1; + pch_udc_ep_disable(ep); + pch_udc_disable_ep_interrupts(ep->dev, PCH_UDC_EPINT(ep->in, ep->num)); + ep->desc = NULL; + INIT_LIST_HEAD(&ep->queue); + spin_unlock_irqrestore(&ep->dev->lock, iflags); + return 0; +} + +/** + * pch_udc_alloc_request() - This function allocates request structure. + * It is called by gadget driver + * @usbep: Reference to the USB endpoint structure + * @gfp: Flag to be used while allocating memory + * + * Return codes: + * NULL: Failure + * Allocated address: Success + */ +static struct usb_request *pch_udc_alloc_request(struct usb_ep *usbep, + gfp_t gfp) +{ + struct pch_udc_request *req; + struct pch_udc_ep *ep; + struct pch_udc_data_dma_desc *dma_desc; + struct pch_udc_dev *dev; + + if (!usbep) + return NULL; + ep = container_of(usbep, struct pch_udc_ep, ep); + dev = ep->dev; + req = kzalloc(sizeof *req, gfp); + if (!req) + return NULL; + req->req.dma = DMA_ADDR_INVALID; + INIT_LIST_HEAD(&req->queue); + if (!ep->dev->dma_addr) + return &req->req; + /* ep0 in requests are allocated from data pool here */ + dma_desc = pci_pool_alloc(ep->dev->data_requests, gfp, + &req->td_data_phys); + if (NULL == dma_desc) { + kfree(req); + return NULL; + } + /* prevent from using desc. - set HOST BUSY */ + dma_desc->status |= PCH_UDC_BS_HST_BSY; + dma_desc->dataptr = __constant_cpu_to_le32(DMA_ADDR_INVALID); + req->td_data = dma_desc; + req->td_data_last = dma_desc; + req->chain_len = 1; + return &req->req; +} + +/** + * pch_udc_free_request() - This function frees request structure. + * It is called by gadget driver + * @usbep: Reference to the USB endpoint structure + * @usbreq: Reference to the USB request + */ +static void pch_udc_free_request(struct usb_ep *usbep, + struct usb_request *usbreq) +{ + struct pch_udc_ep *ep; + struct pch_udc_request *req; + struct pch_udc_dev *dev; + + if (!usbep || !usbreq) + return; + ep = container_of(usbep, struct pch_udc_ep, ep); + req = container_of(usbreq, struct pch_udc_request, req); + dev = ep->dev; + if (!list_empty(&req->queue)) + dev_err(&dev->pdev->dev, "%s: %s req=0x%p queue not empty\n", + __func__, usbep->name, req); + if (req->td_data != NULL) { + if (req->chain_len > 1) + pch_udc_free_dma_chain(ep->dev, req); + pci_pool_free(ep->dev->data_requests, req->td_data, + req->td_data_phys); + } + kfree(req); +} + +/** + * pch_udc_pcd_queue() - This function queues a request packet. It is called + * by gadget driver + * @usbep: Reference to the USB endpoint structure + * @usbreq: Reference to the USB request + * @gfp: Flag to be used while mapping the data buffer + * + * Return codes: + * 0: Success + * linux error number: Failure + */ +static int pch_udc_pcd_queue(struct usb_ep *usbep, struct usb_request *usbreq, + gfp_t gfp) +{ + int retval = 0; + struct pch_udc_ep *ep; + struct pch_udc_dev *dev; + struct pch_udc_request *req; + unsigned long iflags; + + if (!usbep || !usbreq || !usbreq->complete || !usbreq->buf) + return -EINVAL; + ep = container_of(usbep, struct pch_udc_ep, ep); + dev = ep->dev; + if (!ep->desc && ep->num) + return -EINVAL; + req = container_of(usbreq, struct pch_udc_request, req); + if (!list_empty(&req->queue)) + return -EINVAL; + if (!dev->driver || (dev->gadget.speed == USB_SPEED_UNKNOWN)) + return -ESHUTDOWN; + spin_lock_irqsave(&ep->dev->lock, iflags); + /* map the buffer for dma */ + if (usbreq->length && + ((usbreq->dma == DMA_ADDR_INVALID) || !usbreq->dma)) { + if (ep->in) + usbreq->dma = pci_map_single(dev->pdev, usbreq->buf, + usbreq->length, PCI_DMA_TODEVICE); + else + usbreq->dma = pci_map_single(dev->pdev, usbreq->buf, + usbreq->length, PCI_DMA_FROMDEVICE); + req->dma_mapped = 1; + } + if (usbreq->length > 0) { + retval = prepare_dma(ep, req, gfp); + if (retval) + goto probe_end; + } + usbreq->actual = 0; + usbreq->status = -EINPROGRESS; + req->dma_done = 0; + if (list_empty(&ep->queue) && !ep->halted) { + /* no pending transfer, so start this req */ + if (!usbreq->length) { + process_zlp(ep, req); + retval = 0; + goto probe_end; + } + if (!ep->in) { + pch_udc_start_rxrequest(ep, req); + } else { + /* + * For IN trfr the descriptors will be programmed and + * P bit will be set when + * we get an IN token + */ + pch_udc_wait_ep_stall(ep); + pch_udc_ep_clear_nak(ep); + pch_udc_enable_ep_interrupts(ep->dev, (1 << ep->num)); + pch_udc_set_dma(dev, DMA_DIR_TX); + } + } + /* Now add this request to the ep's pending requests */ + if (req != NULL) + list_add_tail(&req->queue, &ep->queue); + +probe_end: + spin_unlock_irqrestore(&dev->lock, iflags); + return retval; +} + +/** + * pch_udc_pcd_dequeue() - This function de-queues a request packet. + * It is called by gadget driver + * @usbep: Reference to the USB endpoint structure + * @usbreq: Reference to the USB request + * + * Return codes: + * 0: Success + * linux error number: Failure + */ +static int pch_udc_pcd_dequeue(struct usb_ep *usbep, + struct usb_request *usbreq) +{ + struct pch_udc_ep *ep; + struct pch_udc_request *req; + struct pch_udc_dev *dev; + unsigned long flags; + int ret = -EINVAL; + + ep = container_of(usbep, struct pch_udc_ep, ep); + dev = ep->dev; + if (!usbep || !usbreq || (!ep->desc && ep->num)) + return ret; + req = container_of(usbreq, struct pch_udc_request, req); + spin_lock_irqsave(&ep->dev->lock, flags); + /* make sure it's still queued on this endpoint */ + list_for_each_entry(req, &ep->queue, queue) { + if (&req->req == usbreq) { + pch_udc_ep_set_nak(ep); + if (!list_empty(&req->queue)) + complete_req(ep, req, -ECONNRESET); + ret = 0; + break; + } + } + spin_unlock_irqrestore(&ep->dev->lock, flags); + return ret; +} + +/** + * pch_udc_pcd_set_halt() - This function Sets or clear the endpoint halt + * feature + * @usbep: Reference to the USB endpoint structure + * @halt: Specifies whether to set or clear the feature + * + * Return codes: + * 0: Success + * linux error number: Failure + */ +static int pch_udc_pcd_set_halt(struct usb_ep *usbep, int halt) +{ + struct pch_udc_ep *ep; + struct pch_udc_dev *dev; + unsigned long iflags; + int ret; + + if (!usbep) + return -EINVAL; + ep = container_of(usbep, struct pch_udc_ep, ep); + dev = ep->dev; + if (!ep->desc && !ep->num) + return -EINVAL; + if (!ep->dev->driver || (ep->dev->gadget.speed == USB_SPEED_UNKNOWN)) + return -ESHUTDOWN; + spin_lock_irqsave(&udc_stall_spinlock, iflags); + if (list_empty(&ep->queue)) { + if (halt) { + if (ep->num == PCH_UDC_EP0) + ep->dev->stall = 1; + pch_udc_ep_set_stall(ep); + pch_udc_enable_ep_interrupts(ep->dev, + PCH_UDC_EPINT(ep->in, + ep->num)); + } else { + pch_udc_ep_clear_stall(ep); + } + ret = 0; + } else { + ret = -EAGAIN; + } + spin_unlock_irqrestore(&udc_stall_spinlock, iflags); + return ret; +} + +/** + * pch_udc_pcd_set_wedge() - This function Sets or clear the endpoint + * halt feature + * @usbep: Reference to the USB endpoint structure + * @halt: Specifies whether to set or clear the feature + * + * Return codes: + * 0: Success + * linux error number: Failure + */ +static int pch_udc_pcd_set_wedge(struct usb_ep *usbep) +{ + struct pch_udc_ep *ep; + struct pch_udc_dev *dev; + unsigned long iflags; + int ret; + + if (!usbep) + return -EINVAL; + ep = container_of(usbep, struct pch_udc_ep, ep); + dev = ep->dev; + if (!ep->desc && !ep->num) + return -EINVAL; + if (!ep->dev->driver || (ep->dev->gadget.speed == USB_SPEED_UNKNOWN)) + return -ESHUTDOWN; + spin_lock_irqsave(&udc_stall_spinlock, iflags); + if (!list_empty(&ep->queue)) { + ret = -EAGAIN; + } else { + if (ep->num == PCH_UDC_EP0) + ep->dev->stall = 1; + pch_udc_ep_set_stall(ep); + pch_udc_enable_ep_interrupts(ep->dev, + PCH_UDC_EPINT(ep->in, ep->num)); + ep->dev->prot_stall = 1; + ret = 0; + } + spin_unlock_irqrestore(&udc_stall_spinlock, iflags); + return ret; +} + +/** + * pch_udc_pcd_fifo_flush() - This function Flush the FIFO of specified endpoint + * @usbep: Reference to the USB endpoint structure + */ +static void pch_udc_pcd_fifo_flush(struct usb_ep *usbep) +{ + struct pch_udc_ep *ep; + + if (!usbep) + return; + + ep = container_of(usbep, struct pch_udc_ep, ep); + if (ep->desc || !ep->num) + pch_udc_ep_fifo_flush(ep, ep->in); +} + +static const struct usb_ep_ops pch_udc_ep_ops = { + .enable = pch_udc_pcd_ep_enable, + .disable = pch_udc_pcd_ep_disable, + .alloc_request = pch_udc_alloc_request, + .free_request = pch_udc_free_request, + .queue = pch_udc_pcd_queue, + .dequeue = pch_udc_pcd_dequeue, + .set_halt = pch_udc_pcd_set_halt, + .set_wedge = pch_udc_pcd_set_wedge, + .fifo_status = NULL, + .fifo_flush = pch_udc_pcd_fifo_flush, +}; + +/** + * pch_udc_init_setup_buff() - This function initializes the SETUP buffer + * @td_stp: Reference to the SETP buffer structure + */ +static void pch_udc_init_setup_buff(struct pch_udc_stp_dma_desc *td_stp) +{ + static u32 pky_marker; + + if (!td_stp) + return; + td_stp->reserved = ++pky_marker; + memset(&td_stp->request, 0xFF, sizeof td_stp->request); + td_stp->status = PCH_UDC_BS_HST_RDY; +} + +/** + * pch_udc_start_next_txrequest() - This function starts + * the next transmission requirement + * @ep: Reference to the endpoint structure + */ +static void pch_udc_start_next_txrequest(struct pch_udc_ep *ep) +{ + struct pch_udc_request *req; + struct pch_udc_data_dma_desc *td_data; + + if (pch_udc_read_ep_control(ep) & UDC_EPCTL_P) + return; + + if (list_empty(&ep->queue)) + return; + + /* next request */ + req = list_entry(ep->queue.next, struct pch_udc_request, queue); + if (req->dma_going) + return; + if (!req->td_data) + return; + pch_udc_wait_ep_stall(ep); + req->dma_going = 1; + pch_udc_ep_set_ddptr(ep, 0); + td_data = req->td_data; + while (1) { + td_data->status = (td_data->status & ~PCH_UDC_BUFF_STS) | + PCH_UDC_BS_HST_RDY; + if ((td_data->status & PCH_UDC_DMA_LAST) == PCH_UDC_DMA_LAST) + break; + td_data = phys_to_virt(td_data->next); + } + pch_udc_ep_set_ddptr(ep, req->td_data_phys); + pch_udc_set_dma(ep->dev, DMA_DIR_TX); + pch_udc_ep_set_pd(ep); + pch_udc_enable_ep_interrupts(ep->dev, PCH_UDC_EPINT(ep->in, ep->num)); + pch_udc_ep_clear_nak(ep); +} + +/** + * pch_udc_complete_transfer() - This function completes a transfer + * @ep: Reference to the endpoint structure + */ +static void pch_udc_complete_transfer(struct pch_udc_ep *ep) +{ + struct pch_udc_request *req; + struct pch_udc_dev *dev = ep->dev; + + if (list_empty(&ep->queue)) + return; + req = list_entry(ep->queue.next, struct pch_udc_request, queue); + if ((req->td_data_last->status & PCH_UDC_BUFF_STS) != + PCH_UDC_BS_DMA_DONE) + return; + if ((req->td_data_last->status & PCH_UDC_RXTX_STS) != + PCH_UDC_RTS_SUCC) { + dev_err(&dev->pdev->dev, "Invalid RXTX status (0x%08x) " + "epstatus=0x%08x\n", + (req->td_data_last->status & PCH_UDC_RXTX_STS), + (int)(ep->epsts)); + return; + } + + req->req.actual = req->req.length; + req->td_data_last->status = PCH_UDC_BS_HST_BSY | PCH_UDC_DMA_LAST; + req->td_data->status = PCH_UDC_BS_HST_BSY | PCH_UDC_DMA_LAST; + complete_req(ep, req, 0); + req->dma_going = 0; + if (!list_empty(&ep->queue)) { + pch_udc_wait_ep_stall(ep); + pch_udc_ep_clear_nak(ep); + pch_udc_enable_ep_interrupts(ep->dev, + PCH_UDC_EPINT(ep->in, ep->num)); + } else { + pch_udc_disable_ep_interrupts(ep->dev, + PCH_UDC_EPINT(ep->in, ep->num)); + } +} + +/** + * pch_udc_complete_receiver() - This function completes a receiver + * @ep: Reference to the endpoint structure + */ +static void pch_udc_complete_receiver(struct pch_udc_ep *ep) +{ + struct pch_udc_request *req; + struct pch_udc_dev *dev = ep->dev; + unsigned int count; + + if (list_empty(&ep->queue)) + return; + + /* next request */ + req = list_entry(ep->queue.next, struct pch_udc_request, queue); + if ((req->td_data_last->status & PCH_UDC_BUFF_STS) != + PCH_UDC_BS_DMA_DONE) + return; + pch_udc_clear_dma(ep->dev, DMA_DIR_RX); + if ((req->td_data_last->status & PCH_UDC_RXTX_STS) != + PCH_UDC_RTS_SUCC) { + dev_err(&dev->pdev->dev, "Invalid RXTX status (0x%08x) " + "epstatus=0x%08x\n", + (req->td_data_last->status & PCH_UDC_RXTX_STS), + (int)(ep->epsts)); + return; + } + count = req->td_data_last->status & PCH_UDC_RXTX_BYTES; + + /* on 64k packets the RXBYTES field is zero */ + if (!count && (req->req.length == UDC_DMA_MAXPACKET)) + count = UDC_DMA_MAXPACKET; + req->td_data->status |= PCH_UDC_DMA_LAST; + req->td_data_last->status |= PCH_UDC_BS_HST_BSY; + + req->dma_going = 0; + req->req.actual = count; + complete_req(ep, req, 0); + /* If there is a new/failed requests try that now */ + if (!list_empty(&ep->queue)) { + req = list_entry(ep->queue.next, struct pch_udc_request, queue); + pch_udc_start_rxrequest(ep, req); + } +} + +/** + * pch_udc_svc_data_in() - This function process endpoint interrupts + * for IN endpoints + * @dev: Reference to the device structure + * @ep_num: Endpoint that generated the interrupt + */ +static void pch_udc_svc_data_in(struct pch_udc_dev *dev, int ep_num) +{ + u32 epsts; + struct pch_udc_ep *ep; + + ep = &dev->ep[2*ep_num]; + epsts = ep->epsts; + ep->epsts = 0; + + if (!(epsts & (UDC_EPSTS_IN | UDC_EPSTS_BNA | UDC_EPSTS_HE | + UDC_EPSTS_TDC | UDC_EPSTS_RCS | UDC_EPSTS_TXEMPTY | + UDC_EPSTS_RSS | UDC_EPSTS_XFERDONE))) + return; + if ((epsts & UDC_EPSTS_BNA)) + return; + if (epsts & UDC_EPSTS_HE) + return; + if (epsts & UDC_EPSTS_RSS) { + pch_udc_ep_set_stall(ep); + pch_udc_enable_ep_interrupts(ep->dev, + PCH_UDC_EPINT(ep->in, ep->num)); + } + if (epsts & UDC_EPSTS_RCS) { + if (!dev->prot_stall) { + pch_udc_ep_clear_stall(ep); + } else { + pch_udc_ep_set_stall(ep); + pch_udc_enable_ep_interrupts(ep->dev, + PCH_UDC_EPINT(ep->in, ep->num)); + } + } + if (epsts & UDC_EPSTS_TDC) + pch_udc_complete_transfer(ep); + /* On IN interrupt, provide data if we have any */ + if ((epsts & UDC_EPSTS_IN) && !(epsts & UDC_EPSTS_RSS) && + !(epsts & UDC_EPSTS_TDC) && !(epsts & UDC_EPSTS_TXEMPTY)) + pch_udc_start_next_txrequest(ep); +} + +/** + * pch_udc_svc_data_out() - Handles interrupts from OUT endpoint + * @dev: Reference to the device structure + * @ep_num: Endpoint that generated the interrupt + */ +static void pch_udc_svc_data_out(struct pch_udc_dev *dev, int ep_num) +{ + u32 epsts; + struct pch_udc_ep *ep; + struct pch_udc_request *req = NULL; + + ep = &dev->ep[2*ep_num + 1]; + epsts = ep->epsts; + ep->epsts = 0; + + if ((epsts & UDC_EPSTS_BNA) && (!list_empty(&ep->queue))) { + /* next request */ + req = list_entry(ep->queue.next, struct pch_udc_request, + queue); + if ((req->td_data_last->status & PCH_UDC_BUFF_STS) != + PCH_UDC_BS_DMA_DONE) { + if (!req->dma_going) + pch_udc_start_rxrequest(ep, req); + return; + } + } + if (epsts & UDC_EPSTS_HE) + return; + if (epsts & UDC_EPSTS_RSS) + pch_udc_ep_set_stall(ep); + pch_udc_enable_ep_interrupts(ep->dev, + PCH_UDC_EPINT(ep->in, ep->num)); + if (epsts & UDC_EPSTS_RCS) { + if (!dev->prot_stall) { + pch_udc_ep_clear_stall(ep); + } else { + pch_udc_ep_set_stall(ep); + pch_udc_enable_ep_interrupts(ep->dev, + PCH_UDC_EPINT(ep->in, ep->num)); + } + } + if (((epsts & UDC_EPSTS_OUT_MASK) >> UDC_EPSTS_OUT_SHIFT) == + UDC_EPSTS_OUT_DATA) { + if (ep->dev->prot_stall == 1) { + pch_udc_ep_set_stall(ep); + pch_udc_enable_ep_interrupts(ep->dev, + PCH_UDC_EPINT(ep->in, ep->num)); + } else { + pch_udc_complete_receiver(ep); + } + } + if (list_empty(&ep->queue)) + pch_udc_set_dma(dev, DMA_DIR_RX); +} + +/** + * pch_udc_svc_control_in() - Handle Control IN endpoint interrupts + * @dev: Reference to the device structure + */ +static void pch_udc_svc_control_in(struct pch_udc_dev *dev) +{ + u32 epsts; + struct pch_udc_ep *ep; + + ep = &dev->ep[UDC_EP0IN_IDX]; + epsts = ep->epsts; + ep->epsts = 0; + + if (!(epsts & (UDC_EPSTS_IN | UDC_EPSTS_BNA | UDC_EPSTS_HE | + UDC_EPSTS_TDC | UDC_EPSTS_RCS | UDC_EPSTS_TXEMPTY | + UDC_EPSTS_XFERDONE))) + return; + if ((epsts & UDC_EPSTS_BNA)) + return; + if (epsts & UDC_EPSTS_HE) + return; + if ((epsts & UDC_EPSTS_TDC) && (!dev->stall)) + pch_udc_complete_transfer(ep); + /* On IN interrupt, provide data if we have any */ + if ((epsts & UDC_EPSTS_IN) && !(epsts & UDC_EPSTS_TDC) && + !(epsts & UDC_EPSTS_TXEMPTY)) + pch_udc_start_next_txrequest(ep); +} + +/** + * pch_udc_svc_control_out() - Routine that handle Control + * OUT endpoint interrupts + * @dev: Reference to the device structure + */ +static void pch_udc_svc_control_out(struct pch_udc_dev *dev) +{ + u32 stat; + int setup_supported; + struct pch_udc_ep *ep; + + ep = &dev->ep[UDC_EP0OUT_IDX]; + stat = ep->epsts; + ep->epsts = 0; + + /* If setup data */ + if (((stat & UDC_EPSTS_OUT_MASK) >> UDC_EPSTS_OUT_SHIFT) == + UDC_EPSTS_OUT_SETUP) { + dev->stall = 0; + dev->ep[UDC_EP0IN_IDX].halted = 0; + dev->ep[UDC_EP0OUT_IDX].halted = 0; + /* In data not ready */ + pch_udc_ep_set_nak(&(dev->ep[UDC_EP0IN_IDX])); + dev->setup_data = ep->td_stp->request; + pch_udc_init_setup_buff(ep->td_stp); + pch_udc_clear_dma(dev, DMA_DIR_TX); + pch_udc_ep_fifo_flush(&(dev->ep[UDC_EP0IN_IDX]), + dev->ep[UDC_EP0IN_IDX].in); + if ((dev->setup_data.bRequestType & USB_DIR_IN)) + dev->gadget.ep0 = &dev->ep[UDC_EP0IN_IDX].ep; + else /* OUT */ + dev->gadget.ep0 = &ep->ep; + spin_unlock(&dev->lock); + /* If Mass storage Reset */ + if ((dev->setup_data.bRequestType == 0x21) && + (dev->setup_data.bRequest == 0xFF)) + dev->prot_stall = 0; + /* call gadget with setup data received */ + setup_supported = dev->driver->setup(&dev->gadget, + &dev->setup_data); + spin_lock(&dev->lock); + /* ep0 in returns data on IN phase */ + if (setup_supported >= 0 && setup_supported < + UDC_EP0IN_MAX_PKT_SIZE) { + pch_udc_ep_clear_nak(&(dev->ep[UDC_EP0IN_IDX])); + /* Gadget would have queued a request when + * we called the setup */ + pch_udc_set_dma(dev, DMA_DIR_RX); + pch_udc_ep_clear_nak(ep); + } else if (setup_supported < 0) { + /* if unsupported request, then stall */ + pch_udc_ep_set_stall(&(dev->ep[UDC_EP0IN_IDX])); + pch_udc_enable_ep_interrupts(ep->dev, + PCH_UDC_EPINT(ep->in, ep->num)); + dev->stall = 0; + pch_udc_set_dma(dev, DMA_DIR_RX); + } else { + dev->waiting_zlp_ack = 1; + } + } else if ((((stat & UDC_EPSTS_OUT_MASK) >> UDC_EPSTS_OUT_SHIFT) == + UDC_EPSTS_OUT_DATA) && !dev->stall) { + if (list_empty(&ep->queue)) { + dev_err(&dev->pdev->dev, "%s: No request\n", __func__); + ep->td_data->status = (ep->td_data->status & + ~PCH_UDC_BUFF_STS) | + PCH_UDC_BS_HST_RDY; + pch_udc_set_dma(dev, DMA_DIR_RX); + } else { + /* control write */ + /* next function will pickuo an clear the status */ + ep->epsts = stat; + + pch_udc_svc_data_out(dev, 0); + /* re-program desc. pointer for possible ZLPs */ + pch_udc_ep_set_ddptr(ep, ep->td_data_phys); + pch_udc_set_dma(dev, DMA_DIR_RX); + } + } + pch_udc_ep_set_rrdy(ep); +} + + +/** + * pch_udc_postsvc_epinters() - This function enables end point interrupts + * and clears NAK status + * @dev: Reference to the device structure + * @ep_num: End point number + */ +static void pch_udc_postsvc_epinters(struct pch_udc_dev *dev, int ep_num) +{ + struct pch_udc_ep *ep; + struct pch_udc_request *req; + + ep = &dev->ep[2*ep_num]; + if (!list_empty(&ep->queue)) { + req = list_entry(ep->queue.next, struct pch_udc_request, queue); + pch_udc_enable_ep_interrupts(ep->dev, + PCH_UDC_EPINT(ep->in, ep->num)); + pch_udc_ep_clear_nak(ep); + } +} + +/** + * pch_udc_read_all_epstatus() - This function read all endpoint status + * @dev: Reference to the device structure + * @ep_intr: Status of endpoint interrupt + */ +static void pch_udc_read_all_epstatus(struct pch_udc_dev *dev, u32 ep_intr) +{ + int i; + struct pch_udc_ep *ep; + + for (i = 0; i < PCH_UDC_USED_EP_NUM; i++) { + /* IN */ + if (ep_intr & (0x1 << i)) { + ep = &dev->ep[2*i]; + ep->epsts = pch_udc_read_ep_status(ep); + pch_udc_clear_ep_status(ep, ep->epsts); + } + /* OUT */ + if (ep_intr & (0x10000 << i)) { + ep = &dev->ep[2*i+1]; + ep->epsts = pch_udc_read_ep_status(ep); + pch_udc_clear_ep_status(ep, ep->epsts); + } + } +} + +/** + * pch_udc_activate_control_ep() - This function enables the control endpoints + * for traffic after a reset + * @dev: Reference to the device structure + */ +static void pch_udc_activate_control_ep(struct pch_udc_dev *dev) +{ + struct pch_udc_ep *ep; + u32 val; + + /* Setup the IN endpoint */ + ep = &dev->ep[UDC_EP0IN_IDX]; + pch_udc_clear_ep_control(ep); + pch_udc_ep_fifo_flush(ep, ep->in); + pch_udc_ep_set_bufsz(ep, UDC_EP0IN_BUFF_SIZE, ep->in); + pch_udc_ep_set_maxpkt(ep, UDC_EP0IN_MAX_PKT_SIZE); + /* Initialize the IN EP Descriptor */ + ep->td_data = NULL; + ep->td_stp = NULL; + ep->td_data_phys = 0; + ep->td_stp_phys = 0; + + /* Setup the OUT endpoint */ + ep = &dev->ep[UDC_EP0OUT_IDX]; + pch_udc_clear_ep_control(ep); + pch_udc_ep_fifo_flush(ep, ep->in); + pch_udc_ep_set_bufsz(ep, UDC_EP0OUT_BUFF_SIZE, ep->in); + pch_udc_ep_set_maxpkt(ep, UDC_EP0OUT_MAX_PKT_SIZE); + val = UDC_EP0OUT_MAX_PKT_SIZE << UDC_CSR_NE_MAX_PKT_SHIFT; + pch_udc_write_csr(ep->dev, val, UDC_EP0OUT_IDX); + + /* Initialize the SETUP buffer */ + pch_udc_init_setup_buff(ep->td_stp); + /* Write the pointer address of dma descriptor */ + pch_udc_ep_set_subptr(ep, ep->td_stp_phys); + /* Write the pointer address of Setup descriptor */ + pch_udc_ep_set_ddptr(ep, ep->td_data_phys); + + /* Initialize the dma descriptor */ + ep->td_data->status = PCH_UDC_DMA_LAST; + ep->td_data->dataptr = dev->dma_addr; + ep->td_data->next = ep->td_data_phys; + + pch_udc_ep_clear_nak(ep); +} + + +/** + * pch_udc_svc_ur_interrupt() - This function handles a USB reset interrupt + * @dev: Reference to driver structure + */ +static void pch_udc_svc_ur_interrupt(struct pch_udc_dev *dev) +{ + struct pch_udc_ep *ep; + int i; + + pch_udc_clear_dma(dev, DMA_DIR_TX); + pch_udc_clear_dma(dev, DMA_DIR_RX); + /* Mask all endpoint interrupts */ + pch_udc_disable_ep_interrupts(dev, UDC_EPINT_MSK_DISABLE_ALL); + /* clear all endpoint interrupts */ + pch_udc_write_ep_interrupts(dev, UDC_EPINT_MSK_DISABLE_ALL); + + for (i = 0; i < PCH_UDC_EP_NUM; i++) { + ep = &dev->ep[i]; + pch_udc_clear_ep_status(ep, UDC_EPSTS_ALL_CLR_MASK); + pch_udc_clear_ep_control(ep); + pch_udc_ep_set_ddptr(ep, 0); + pch_udc_write_csr(ep->dev, 0x00, i); + } + dev->stall = 0; + dev->prot_stall = 0; + dev->waiting_zlp_ack = 0; + dev->set_cfg_not_acked = 0; + + /* disable ep to empty req queue. Skip the control EP's */ + for (i = 0; i < (PCH_UDC_USED_EP_NUM*2); i++) { + ep = &dev->ep[i]; + pch_udc_ep_set_nak(ep); + pch_udc_ep_fifo_flush(ep, ep->in); + /* Complete request queue */ + empty_req_queue(ep); + } + if (dev->driver && dev->driver->disconnect) + dev->driver->disconnect(&dev->gadget); +} + +/** + * pch_udc_svc_enum_interrupt() - This function handles a USB speed enumeration + * done interrupt + * @dev: Reference to driver structure + */ +static void pch_udc_svc_enum_interrupt(struct pch_udc_dev *dev) +{ + u32 dev_stat, dev_speed; + u32 speed = USB_SPEED_FULL; + + dev_stat = pch_udc_read_device_status(dev); + dev_speed = (dev_stat & UDC_DEVSTS_ENUM_SPEED_MASK) >> + UDC_DEVSTS_ENUM_SPEED_SHIFT; + switch (dev_speed) { + case UDC_DEVSTS_ENUM_SPEED_HIGH: + speed = USB_SPEED_HIGH; + break; + case UDC_DEVSTS_ENUM_SPEED_FULL: + speed = USB_SPEED_FULL; + break; + case UDC_DEVSTS_ENUM_SPEED_LOW: + speed = USB_SPEED_LOW; + break; + default: + BUG(); + } + dev->gadget.speed = speed; + pch_udc_activate_control_ep(dev); + pch_udc_enable_ep_interrupts(dev, UDC_EPINT_IN_EP0 | UDC_EPINT_OUT_EP0); + pch_udc_set_dma(dev, DMA_DIR_TX); + pch_udc_set_dma(dev, DMA_DIR_RX); + pch_udc_ep_set_rrdy(&(dev->ep[UDC_EP0OUT_IDX])); +} + +/** + * pch_udc_svc_intf_interrupt() - This function handles a set interface + * interrupt + * @dev: Reference to driver structure + */ +static void pch_udc_svc_intf_interrupt(struct pch_udc_dev *dev) +{ + u32 reg, dev_stat = 0; + int i, ret; + + dev_stat = pch_udc_read_device_status(dev); + dev->cfg_data.cur_intf = (dev_stat & UDC_DEVSTS_INTF_MASK) >> + UDC_DEVSTS_INTF_SHIFT; + dev->cfg_data.cur_alt = (dev_stat & UDC_DEVSTS_ALT_MASK) >> + UDC_DEVSTS_ALT_SHIFT; + dev->set_cfg_not_acked = 1; + /* Construct the usb request for gadget driver and inform it */ + memset(&dev->setup_data, 0 , sizeof dev->setup_data); + dev->setup_data.bRequest = USB_REQ_SET_INTERFACE; + dev->setup_data.bRequestType = USB_RECIP_INTERFACE; + dev->setup_data.wValue = cpu_to_le16(dev->cfg_data.cur_alt); + dev->setup_data.wIndex = cpu_to_le16(dev->cfg_data.cur_intf); + /* programm the Endpoint Cfg registers */ + /* Only one end point cfg register */ + reg = pch_udc_read_csr(dev, UDC_EP0OUT_IDX); + reg = (reg & ~UDC_CSR_NE_INTF_MASK) | + (dev->cfg_data.cur_intf << UDC_CSR_NE_INTF_SHIFT); + reg = (reg & ~UDC_CSR_NE_ALT_MASK) | + (dev->cfg_data.cur_alt << UDC_CSR_NE_ALT_SHIFT); + pch_udc_write_csr(dev, reg, UDC_EP0OUT_IDX); + for (i = 0; i < PCH_UDC_USED_EP_NUM * 2; i++) { + /* clear stall bits */ + pch_udc_ep_clear_stall(&(dev->ep[i])); + dev->ep[i].halted = 0; + } + dev->stall = 0; + spin_unlock(&dev->lock); + ret = dev->driver->setup(&dev->gadget, &dev->setup_data); + spin_lock(&dev->lock); +} + +/** + * pch_udc_svc_cfg_interrupt() - This function handles a set configuration + * interrupt + * @dev: Reference to driver structure + */ +static void pch_udc_svc_cfg_interrupt(struct pch_udc_dev *dev) +{ + int i, ret; + u32 reg, dev_stat = 0; + + dev_stat = pch_udc_read_device_status(dev); + dev->set_cfg_not_acked = 1; + dev->cfg_data.cur_cfg = (dev_stat & UDC_DEVSTS_CFG_MASK) >> + UDC_DEVSTS_CFG_SHIFT; + /* make usb request for gadget driver */ + memset(&dev->setup_data, 0 , sizeof dev->setup_data); + dev->setup_data.bRequest = USB_REQ_SET_CONFIGURATION; + dev->setup_data.wValue = cpu_to_le16(dev->cfg_data.cur_cfg); + /* program the NE registers */ + /* Only one end point cfg register */ + reg = pch_udc_read_csr(dev, UDC_EP0OUT_IDX); + reg = (reg & ~UDC_CSR_NE_CFG_MASK) | + (dev->cfg_data.cur_cfg << UDC_CSR_NE_CFG_SHIFT); + pch_udc_write_csr(dev, reg, UDC_EP0OUT_IDX); + for (i = 0; i < PCH_UDC_USED_EP_NUM * 2; i++) { + /* clear stall bits */ + pch_udc_ep_clear_stall(&(dev->ep[i])); + dev->ep[i].halted = 0; + } + dev->stall = 0; + + /* call gadget zero with setup data received */ + spin_unlock(&dev->lock); + ret = dev->driver->setup(&dev->gadget, &dev->setup_data); + spin_lock(&dev->lock); +} + +/** + * pch_udc_dev_isr() - This function services device interrupts + * by invoking appropriate routines. + * @dev: Reference to the device structure + * @dev_intr: The Device interrupt status. + */ +static void pch_udc_dev_isr(struct pch_udc_dev *dev, u32 dev_intr) +{ + /* USB Reset Interrupt */ + if (dev_intr & UDC_DEVINT_UR) + pch_udc_svc_ur_interrupt(dev); + /* Enumeration Done Interrupt */ + if (dev_intr & UDC_DEVINT_ENUM) + pch_udc_svc_enum_interrupt(dev); + /* Set Interface Interrupt */ + if (dev_intr & UDC_DEVINT_SI) + pch_udc_svc_intf_interrupt(dev); + /* Set Config Interrupt */ + if (dev_intr & UDC_DEVINT_SC) + pch_udc_svc_cfg_interrupt(dev); + /* USB Suspend interrupt */ + if (dev_intr & UDC_DEVINT_US) + dev_dbg(&dev->pdev->dev, "USB_SUSPEND\n"); + /* Clear the SOF interrupt, if enabled */ + if (dev_intr & UDC_DEVINT_SOF) + dev_dbg(&dev->pdev->dev, "SOF\n"); + /* ES interrupt, IDLE > 3ms on the USB */ + if (dev_intr & UDC_DEVINT_ES) + dev_dbg(&dev->pdev->dev, "ES\n"); + /* RWKP interrupt */ + if (dev_intr & UDC_DEVINT_RWKP) + dev_dbg(&dev->pdev->dev, "RWKP\n"); +} + +/** + * pch_udc_isr() - This function handles interrupts from the PCH USB Device + * @irq: Interrupt request number + * @dev: Reference to the device structure + */ +static irqreturn_t pch_udc_isr(int irq, void *pdev) +{ + struct pch_udc_dev *dev = (struct pch_udc_dev *) pdev; + u32 dev_intr, ep_intr; + int i; + + dev_intr = pch_udc_read_device_interrupts(dev); + ep_intr = pch_udc_read_ep_interrupts(dev); + + if (dev_intr) + /* Clear device interrupts */ + pch_udc_write_device_interrupts(dev, dev_intr); + if (ep_intr) + /* Clear ep interrupts */ + pch_udc_write_ep_interrupts(dev, ep_intr); + if (!dev_intr && !ep_intr) + return IRQ_NONE; + spin_lock(&dev->lock); + if (dev_intr) + pch_udc_dev_isr(dev, dev_intr); + if (ep_intr) { + pch_udc_read_all_epstatus(dev, ep_intr); + /* Process Control In interrupts, if present */ + if (ep_intr & UDC_EPINT_IN_EP0) { + pch_udc_svc_control_in(dev); + pch_udc_postsvc_epinters(dev, 0); + } + /* Process Control Out interrupts, if present */ + if (ep_intr & UDC_EPINT_OUT_EP0) + pch_udc_svc_control_out(dev); + /* Process data in end point interrupts */ + for (i = 1; i < PCH_UDC_USED_EP_NUM; i++) { + if (ep_intr & (1 << i)) { + pch_udc_svc_data_in(dev, i); + pch_udc_postsvc_epinters(dev, i); + } + } + /* Process data out end point interrupts */ + for (i = UDC_EPINT_OUT_SHIFT + 1; i < (UDC_EPINT_OUT_SHIFT + + PCH_UDC_USED_EP_NUM); i++) + if (ep_intr & (1 << i)) + pch_udc_svc_data_out(dev, i - + UDC_EPINT_OUT_SHIFT); + } + spin_unlock(&dev->lock); + return IRQ_HANDLED; +} + +/** + * pch_udc_setup_ep0() - This function enables control endpoint for traffic + * @dev: Reference to the device structure + */ +static void pch_udc_setup_ep0(struct pch_udc_dev *dev) +{ + /* enable ep0 interrupts */ + pch_udc_enable_ep_interrupts(dev, UDC_EPINT_IN_EP0 | + UDC_EPINT_OUT_EP0); + /* enable device interrupts */ + pch_udc_enable_interrupts(dev, UDC_DEVINT_UR | UDC_DEVINT_US | + UDC_DEVINT_ES | UDC_DEVINT_ENUM | + UDC_DEVINT_SI | UDC_DEVINT_SC); +} + +/** + * gadget_release() - Free the gadget driver private data + * @pdev reference to struct pci_dev + */ +static void gadget_release(struct device *pdev) +{ + struct pch_udc_dev *dev = dev_get_drvdata(pdev); + + kfree(dev); +} + +/** + * pch_udc_pcd_reinit() - This API initializes the endpoint structures + * @dev: Reference to the driver structure + */ +static void pch_udc_pcd_reinit(struct pch_udc_dev *dev) +{ + const char *const ep_string[] = { + ep0_string, "ep0out", "ep1in", "ep1out", "ep2in", "ep2out", + "ep3in", "ep3out", "ep4in", "ep4out", "ep5in", "ep5out", + "ep6in", "ep6out", "ep7in", "ep7out", "ep8in", "ep8out", + "ep9in", "ep9out", "ep10in", "ep10out", "ep11in", "ep11out", + "ep12in", "ep12out", "ep13in", "ep13out", "ep14in", "ep14out", + "ep15in", "ep15out", + }; + int i; + + dev->gadget.speed = USB_SPEED_UNKNOWN; + INIT_LIST_HEAD(&dev->gadget.ep_list); + + /* Initialize the endpoints structures */ + memset(dev->ep, 0, sizeof dev->ep); + for (i = 0; i < PCH_UDC_EP_NUM; i++) { + struct pch_udc_ep *ep = &dev->ep[i]; + ep->dev = dev; + ep->halted = 1; + ep->num = i / 2; + ep->in = ~i & 1; + ep->ep.name = ep_string[i]; + ep->ep.ops = &pch_udc_ep_ops; + if (ep->in) + ep->offset_addr = ep->num * UDC_EP_REG_SHIFT; + else + ep->offset_addr = (UDC_EPINT_OUT_SHIFT + ep->num) * + UDC_EP_REG_SHIFT; + /* need to set ep->ep.maxpacket and set Default Configuration?*/ + ep->ep.maxpacket = UDC_BULK_MAX_PKT_SIZE; + list_add_tail(&ep->ep.ep_list, &dev->gadget.ep_list); + INIT_LIST_HEAD(&ep->queue); + } + dev->ep[UDC_EP0IN_IDX].ep.maxpacket = UDC_EP0IN_MAX_PKT_SIZE; + dev->ep[UDC_EP0OUT_IDX].ep.maxpacket = UDC_EP0OUT_MAX_PKT_SIZE; + + dev->dma_addr = pci_map_single(dev->pdev, dev->ep0out_buf, 256, + PCI_DMA_FROMDEVICE); + + /* remove ep0 in and out from the list. They have own pointer */ + list_del_init(&dev->ep[UDC_EP0IN_IDX].ep.ep_list); + list_del_init(&dev->ep[UDC_EP0OUT_IDX].ep.ep_list); + + dev->gadget.ep0 = &dev->ep[UDC_EP0IN_IDX].ep; + INIT_LIST_HEAD(&dev->gadget.ep0->ep_list); +} + +/** + * pch_udc_pcd_init() - This API initializes the driver structure + * @dev: Reference to the driver structure + * + * Return codes: + * 0: Success + */ +static int pch_udc_pcd_init(struct pch_udc_dev *dev) +{ + pch_udc_init(dev); + pch_udc_pcd_reinit(dev); + return 0; +} + +/** + * init_dma_pools() - create dma pools during initialization + * @pdev: reference to struct pci_dev + */ +static int init_dma_pools(struct pch_udc_dev *dev) +{ + struct pch_udc_stp_dma_desc *td_stp; + struct pch_udc_data_dma_desc *td_data; + + /* DMA setup */ + dev->data_requests = pci_pool_create("data_requests", dev->pdev, + sizeof(struct pch_udc_data_dma_desc), 0, 0); + if (!dev->data_requests) { + dev_err(&dev->pdev->dev, "%s: can't get request data pool\n", + __func__); + return -ENOMEM; + } + + /* dma desc for setup data */ + dev->stp_requests = pci_pool_create("setup requests", dev->pdev, + sizeof(struct pch_udc_stp_dma_desc), 0, 0); + if (!dev->stp_requests) { + dev_err(&dev->pdev->dev, "%s: can't get setup request pool\n", + __func__); + return -ENOMEM; + } + /* setup */ + td_stp = pci_pool_alloc(dev->stp_requests, GFP_KERNEL, + &dev->ep[UDC_EP0OUT_IDX].td_stp_phys); + if (!td_stp) { + dev_err(&dev->pdev->dev, + "%s: can't allocate setup dma descriptor\n", __func__); + return -ENOMEM; + } + dev->ep[UDC_EP0OUT_IDX].td_stp = td_stp; + + /* data: 0 packets !? */ + td_data = pci_pool_alloc(dev->data_requests, GFP_KERNEL, + &dev->ep[UDC_EP0OUT_IDX].td_data_phys); + if (!td_data) { + dev_err(&dev->pdev->dev, + "%s: can't allocate data dma descriptor\n", __func__); + return -ENOMEM; + } + dev->ep[UDC_EP0OUT_IDX].td_data = td_data; + dev->ep[UDC_EP0IN_IDX].td_stp = NULL; + dev->ep[UDC_EP0IN_IDX].td_stp_phys = 0; + dev->ep[UDC_EP0IN_IDX].td_data = NULL; + dev->ep[UDC_EP0IN_IDX].td_data_phys = 0; + return 0; +} + +int usb_gadget_probe_driver(struct usb_gadget_driver *driver, + int (*bind)(struct usb_gadget *)) +{ + struct pch_udc_dev *dev = pch_udc; + int retval; + + if (!driver || (driver->speed == USB_SPEED_UNKNOWN) || !bind || + !driver->setup || !driver->unbind || !driver->disconnect) { + dev_err(&dev->pdev->dev, + "%s: invalid driver parameter\n", __func__); + return -EINVAL; + } + + if (!dev) + return -ENODEV; + + if (dev->driver) { + dev_err(&dev->pdev->dev, "%s: already bound\n", __func__); + return -EBUSY; + } + driver->driver.bus = NULL; + dev->driver = driver; + dev->gadget.dev.driver = &driver->driver; + + /* Invoke the bind routine of the gadget driver */ + retval = bind(&dev->gadget); + + if (retval) { + dev_err(&dev->pdev->dev, "%s: binding to %s returning %d\n", + __func__, driver->driver.name, retval); + dev->driver = NULL; + dev->gadget.dev.driver = NULL; + return retval; + } + /* get ready for ep0 traffic */ + pch_udc_setup_ep0(dev); + + /* clear SD */ + pch_udc_clear_disconnect(dev); + + dev->connected = 1; + return 0; +} +EXPORT_SYMBOL(usb_gadget_probe_driver); + +int usb_gadget_unregister_driver(struct usb_gadget_driver *driver) +{ + struct pch_udc_dev *dev = pch_udc; + + if (!dev) + return -ENODEV; + + if (!driver || (driver != dev->driver)) { + dev_err(&dev->pdev->dev, + "%s: invalid driver parameter\n", __func__); + return -EINVAL; + } + + pch_udc_disable_interrupts(dev, UDC_DEVINT_MSK); + + /* Assues that there are no pending requets with this driver */ + driver->unbind(&dev->gadget); + dev->gadget.dev.driver = NULL; + dev->driver = NULL; + dev->connected = 0; + + /* set SD */ + pch_udc_set_disconnect(dev); + return 0; +} +EXPORT_SYMBOL(usb_gadget_unregister_driver); + +static void pch_udc_shutdown(struct pci_dev *pdev) +{ + struct pch_udc_dev *dev = pci_get_drvdata(pdev); + + pch_udc_disable_interrupts(dev, UDC_DEVINT_MSK); + pch_udc_disable_ep_interrupts(dev, UDC_EPINT_MSK_DISABLE_ALL); + + /* disable the pullup so the host will think we're gone */ + pch_udc_set_disconnect(dev); +} + +static void pch_udc_remove(struct pci_dev *pdev) +{ + struct pch_udc_dev *dev = pci_get_drvdata(pdev); + + /* gadget driver must not be registered */ + if (dev->driver) + dev_err(&pdev->dev, + "%s: gadget driver still bound!!!\n", __func__); + /* dma pool cleanup */ + if (dev->data_requests) + pci_pool_destroy(dev->data_requests); + + if (dev->stp_requests) { + /* cleanup DMA desc's for ep0in */ + if (dev->ep[UDC_EP0OUT_IDX].td_stp) { + pci_pool_free(dev->stp_requests, + dev->ep[UDC_EP0OUT_IDX].td_stp, + dev->ep[UDC_EP0OUT_IDX].td_stp_phys); + } + if (dev->ep[UDC_EP0OUT_IDX].td_data) { + pci_pool_free(dev->stp_requests, + dev->ep[UDC_EP0OUT_IDX].td_data, + dev->ep[UDC_EP0OUT_IDX].td_data_phys); + } + pci_pool_destroy(dev->stp_requests); + } + + pch_udc_exit(dev); + + if (dev->irq_registered) + free_irq(pdev->irq, dev); + if (dev->base_addr) + iounmap(dev->base_addr); + if (dev->mem_region) + release_mem_region(dev->phys_addr, + pci_resource_len(pdev, PCH_UDC_PCI_BAR)); + if (dev->active) + pci_disable_device(pdev); + if (dev->registered) + device_unregister(&dev->gadget.dev); + kfree(dev); + pci_set_drvdata(pdev, NULL); +} + +#ifdef CONFIG_PM +static int pch_udc_suspend(struct pci_dev *pdev, pm_message_t state) +{ + struct pch_udc_dev *dev = pci_get_drvdata(pdev); + + pch_udc_disable_interrupts(dev, UDC_DEVINT_MSK); + pch_udc_disable_ep_interrupts(dev, UDC_EPINT_MSK_DISABLE_ALL); + + pci_disable_device(pdev); + pci_enable_wake(pdev, PCI_D3hot, 0); + + if (pci_save_state(pdev)) { + dev_err(&pdev->dev, + "%s: could not save PCI config state\n", __func__); + return -ENOMEM; + } + pci_set_power_state(pdev, pci_choose_state(pdev, state)); + return 0; +} + +static int pch_udc_resume(struct pci_dev *pdev) +{ + int ret; + + pci_set_power_state(pdev, PCI_D0); + ret = pci_restore_state(pdev); + if (ret) { + dev_err(&pdev->dev, "%s: pci_restore_state failed\n", __func__); + return ret; + } + ret = pci_enable_device(pdev); + if (ret) { + dev_err(&pdev->dev, "%s: pci_enable_device failed\n", __func__); + return ret; + } + pci_enable_wake(pdev, PCI_D3hot, 0); + return 0; +} +#else +#define pch_udc_suspend NULL +#define pch_udc_resume NULL +#endif /* CONFIG_PM */ + +static int pch_udc_probe(struct pci_dev *pdev, + const struct pci_device_id *id) +{ + unsigned long resource; + unsigned long len; + int retval; + struct pch_udc_dev *dev; + + /* one udc only */ + if (pch_udc) { + pr_err("%s: already probed\n", __func__); + return -EBUSY; + } + /* init */ + dev = kzalloc(sizeof *dev, GFP_KERNEL); + if (!dev) { + pr_err("%s: no memory for device structure\n", __func__); + return -ENOMEM; + } + /* pci setup */ + if (pci_enable_device(pdev) < 0) { + kfree(dev); + pr_err("%s: pci_enable_device failed\n", __func__); + return -ENODEV; + } + dev->active = 1; + pci_set_drvdata(pdev, dev); + + /* PCI resource allocation */ + resource = pci_resource_start(pdev, 1); + len = pci_resource_len(pdev, 1); + + if (!request_mem_region(resource, len, KBUILD_MODNAME)) { + dev_err(&pdev->dev, "%s: pci device used already\n", __func__); + retval = -EBUSY; + goto finished; + } + dev->phys_addr = resource; + dev->mem_region = 1; + + dev->base_addr = ioremap_nocache(resource, len); + if (!dev->base_addr) { + pr_err("%s: device memory cannot be mapped\n", __func__); + retval = -ENOMEM; + goto finished; + } + if (!pdev->irq) { + dev_err(&pdev->dev, "%s: irq not set\n", __func__); + retval = -ENODEV; + goto finished; + } + pch_udc = dev; + /* initialize the hardware */ + if (pch_udc_pcd_init(dev)) + goto finished; + if (request_irq(pdev->irq, pch_udc_isr, IRQF_SHARED, KBUILD_MODNAME, + dev)) { + dev_err(&pdev->dev, "%s: request_irq(%d) fail\n", __func__, + pdev->irq); + retval = -ENODEV; + goto finished; + } + dev->irq = pdev->irq; + dev->irq_registered = 1; + + pci_set_master(pdev); + pci_try_set_mwi(pdev); + + /* device struct setup */ + spin_lock_init(&dev->lock); + dev->pdev = pdev; + dev->gadget.ops = &pch_udc_ops; + + retval = init_dma_pools(dev); + if (retval) + goto finished; + + dev_set_name(&dev->gadget.dev, "gadget"); + dev->gadget.dev.parent = &pdev->dev; + dev->gadget.dev.dma_mask = pdev->dev.dma_mask; + dev->gadget.dev.release = gadget_release; + dev->gadget.name = KBUILD_MODNAME; + dev->gadget.is_dualspeed = 1; + + retval = device_register(&dev->gadget.dev); + if (retval) + goto finished; + dev->registered = 1; + + /* Put the device in disconnected state till a driver is bound */ + pch_udc_set_disconnect(dev); + return 0; + +finished: + pch_udc_remove(pdev); + return retval; +} + +static DEFINE_PCI_DEVICE_TABLE(pch_udc_pcidev_id) = { + { + PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EG20T_UDC), + .class = (PCI_CLASS_SERIAL_USB << 8) | 0xfe, + .class_mask = 0xffffffff, + }, + { 0 }, +}; + +MODULE_DEVICE_TABLE(pci, pch_udc_pcidev_id); + + +static struct pci_driver pch_udc_driver = { + .name = KBUILD_MODNAME, + .id_table = pch_udc_pcidev_id, + .probe = pch_udc_probe, + .remove = pch_udc_remove, + .suspend = pch_udc_suspend, + .resume = pch_udc_resume, + .shutdown = pch_udc_shutdown, +}; + +static int __init pch_udc_pci_init(void) +{ + return pci_register_driver(&pch_udc_driver); +} +module_init(pch_udc_pci_init); + +static void __exit pch_udc_pci_exit(void) +{ + pci_unregister_driver(&pch_udc_driver); +} +module_exit(pch_udc_pci_exit); + +MODULE_DESCRIPTION("Intel EG20T USB Device Controller"); +MODULE_AUTHOR("OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com>"); +MODULE_LICENSE("GPL"); diff --git a/drivers/usb/gadget/u_audio.c b/drivers/usb/gadget/u_audio.c index 7a86d2c9109c..59ffe1ecf1c9 100644 --- a/drivers/usb/gadget/u_audio.c +++ b/drivers/usb/gadget/u_audio.c @@ -255,6 +255,7 @@ static int gaudio_open_snd_dev(struct gaudio *card) ERROR(card, "No such PCM capture device: %s\n", fn_cap); snd->substream = NULL; snd->card = NULL; + snd->filp = NULL; } else { pcm_file = snd->filp->private_data; snd->substream = pcm_file->substream; @@ -273,17 +274,17 @@ static int gaudio_close_snd_dev(struct gaudio *gau) /* Close control device */ snd = &gau->control; - if (!IS_ERR(snd->filp)) + if (snd->filp) filp_close(snd->filp, current->files); /* Close PCM playback device and setup substream */ snd = &gau->playback; - if (!IS_ERR(snd->filp)) + if (snd->filp) filp_close(snd->filp, current->files); /* Close PCM capture device and setup substream */ snd = &gau->capture; - if (!IS_ERR(snd->filp)) + if (snd->filp) filp_close(snd->filp, current->files); return 0; @@ -304,8 +305,7 @@ int __init gaudio_setup(struct gaudio *card) ret = gaudio_open_snd_dev(card); if (ret) ERROR(card, "we need at least one control device\n"); - - if (!the_card) + else if (!the_card) the_card = card; return ret; diff --git a/drivers/usb/gadget/u_ether.c b/drivers/usb/gadget/u_ether.c index fbe86ca95802..e3454fe46b47 100644 --- a/drivers/usb/gadget/u_ether.c +++ b/drivers/usb/gadget/u_ether.c @@ -240,6 +240,9 @@ rx_submit(struct eth_dev *dev, struct usb_request *req, gfp_t gfp_flags) size += out->maxpacket - 1; size -= size % out->maxpacket; + if (dev->port_usb->is_fixed) + size = max(size, dev->port_usb->fixed_out_len); + skb = alloc_skb(size + NET_IP_ALIGN, gfp_flags); if (skb == NULL) { DBG(dev, "no rx skb\n"); @@ -578,12 +581,19 @@ static netdev_tx_t eth_start_xmit(struct sk_buff *skb, req->context = skb; req->complete = tx_complete; + /* NCM requires no zlp if transfer is dwNtbInMaxSize */ + if (dev->port_usb->is_fixed && + length == dev->port_usb->fixed_in_len && + (length % in->maxpacket) == 0) + req->zero = 0; + else + req->zero = 1; + /* use zlp framing on tx for strict CDC-Ether conformance, * though any robust network rx path ignores extra padding. * and some hardware doesn't like to write zlps. */ - req->zero = 1; - if (!dev->zlp && (length % in->maxpacket) == 0) + if (req->zero && !dev->zlp && (length % in->maxpacket) == 0) length++; req->length = length; diff --git a/drivers/usb/gadget/u_ether.h b/drivers/usb/gadget/u_ether.h index 3c8c0c9f9d72..b56e1e7d423c 100644 --- a/drivers/usb/gadget/u_ether.h +++ b/drivers/usb/gadget/u_ether.h @@ -62,6 +62,10 @@ struct gether { /* hooks for added framing, as needed for RNDIS and EEM. */ u32 header_len; + /* NCM requires fixed size bundles */ + bool is_fixed; + u32 fixed_out_len; + u32 fixed_in_len; struct sk_buff *(*wrap)(struct gether *port, struct sk_buff *skb); int (*unwrap)(struct gether *port, @@ -103,6 +107,7 @@ static inline bool can_support_ecm(struct usb_gadget *gadget) /* each configuration may bind one instance of an ethernet link */ int geth_bind_config(struct usb_configuration *c, u8 ethaddr[ETH_ALEN]); int ecm_bind_config(struct usb_configuration *c, u8 ethaddr[ETH_ALEN]); +int ncm_bind_config(struct usb_configuration *c, u8 ethaddr[ETH_ALEN]); int eem_bind_config(struct usb_configuration *c); #ifdef USB_ETH_RNDIS diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index 6f4f8e6a40c7..fa3782a30f0a 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -133,6 +133,25 @@ config USB_EHCI_MXC ---help--- Variation of ARC USB block used in some Freescale chips. +config USB_EHCI_HCD_OMAP + bool "EHCI support for OMAP3 and later chips" + depends on USB_EHCI_HCD && ARCH_OMAP + default y + --- help --- + Enables support for the on-chip EHCI controller on + OMAP3 and later chips. + +config USB_EHCI_MSM + bool "Support for MSM on-chip EHCI USB controller" + depends on USB_EHCI_HCD && ARCH_MSM + select USB_EHCI_ROOT_HUB_TT + select USB_MSM_OTG_72K + ---help--- + Enables support for the USB Host controller present on the + Qualcomm chipsets. Root Hub has inbuilt TT. + This driver depends on OTG driver for PHY initialization, + clock management, powering up VBUS, and power management. + config USB_EHCI_HCD_PPC_OF bool "EHCI support for PPC USB controller on OF platform bus" depends on USB_EHCI_HCD && PPC_OF diff --git a/drivers/usb/host/ehci-atmel.c b/drivers/usb/host/ehci-atmel.c index 51bd0edf544f..d6a69d514a84 100644 --- a/drivers/usb/host/ehci-atmel.c +++ b/drivers/usb/host/ehci-atmel.c @@ -99,6 +99,7 @@ static const struct hc_driver ehci_atmel_hc_driver = { .urb_enqueue = ehci_urb_enqueue, .urb_dequeue = ehci_urb_dequeue, .endpoint_disable = ehci_endpoint_disable, + .endpoint_reset = ehci_endpoint_reset, /* scheduling support */ .get_frame_number = ehci_get_frame, @@ -110,6 +111,8 @@ static const struct hc_driver ehci_atmel_hc_driver = { .bus_resume = ehci_bus_resume, .relinquish_port = ehci_relinquish_port, .port_handed_over = ehci_port_handed_over, + + .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete, }; static int __init ehci_atmel_drv_probe(struct platform_device *pdev) diff --git a/drivers/usb/host/ehci-dbg.c b/drivers/usb/host/ehci-dbg.c index 6e2599661b5b..3be238a24cc5 100644 --- a/drivers/usb/host/ehci-dbg.c +++ b/drivers/usb/host/ehci-dbg.c @@ -879,7 +879,7 @@ static int fill_buffer(struct debug_buffer *buf) int ret = 0; if (!buf->output_buf) - buf->output_buf = (char *)vmalloc(buf->alloc_size); + buf->output_buf = vmalloc(buf->alloc_size); if (!buf->output_buf) { ret = -ENOMEM; diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index e9062806d4a2..72732daa3b3e 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -114,6 +114,9 @@ MODULE_PARM_DESC(hird, "host initiated resume duration, +1 for each 75us\n"); #define INTR_MASK (STS_IAA | STS_FATAL | STS_PCD | STS_ERR | STS_INT) +/* for ASPM quirk of ISOC on AMD SB800 */ +static struct pci_dev *amd_nb_dev; + /*-------------------------------------------------------------------------*/ #include "ehci.h" @@ -529,6 +532,11 @@ static void ehci_stop (struct usb_hcd *hcd) spin_unlock_irq (&ehci->lock); ehci_mem_cleanup (ehci); + if (amd_nb_dev) { + pci_dev_put(amd_nb_dev); + amd_nb_dev = NULL; + } + #ifdef EHCI_STATS ehci_dbg (ehci, "irq normal %ld err %ld reclaim %ld (lost %ld)\n", ehci->stats.normal, ehci->stats.error, ehci->stats.reclaim, @@ -1166,12 +1174,17 @@ MODULE_LICENSE ("GPL"); #define PLATFORM_DRIVER ehci_mxc_driver #endif +#ifdef CONFIG_CPU_SUBTYPE_SH7786 +#include "ehci-sh.c" +#define PLATFORM_DRIVER ehci_hcd_sh_driver +#endif + #ifdef CONFIG_SOC_AU1200 #include "ehci-au1xxx.c" #define PLATFORM_DRIVER ehci_hcd_au1xxx_driver #endif -#ifdef CONFIG_ARCH_OMAP3 +#ifdef CONFIG_USB_EHCI_HCD_OMAP #include "ehci-omap.c" #define PLATFORM_DRIVER ehci_hcd_omap_driver #endif @@ -1216,6 +1229,21 @@ MODULE_LICENSE ("GPL"); #define PLATFORM_DRIVER ehci_octeon_driver #endif +#ifdef CONFIG_ARCH_VT8500 +#include "ehci-vt8500.c" +#define PLATFORM_DRIVER vt8500_ehci_driver +#endif + +#ifdef CONFIG_PLAT_SPEAR +#include "ehci-spear.c" +#define PLATFORM_DRIVER spear_ehci_hcd_driver +#endif + +#ifdef CONFIG_USB_EHCI_MSM +#include "ehci-msm.c" +#define PLATFORM_DRIVER ehci_msm_driver +#endif + #if !defined(PCI_DRIVER) && !defined(PLATFORM_DRIVER) && \ !defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER) && \ !defined(XILINX_OF_PLATFORM_DRIVER) diff --git a/drivers/usb/host/ehci-msm.c b/drivers/usb/host/ehci-msm.c new file mode 100644 index 000000000000..413f4deca532 --- /dev/null +++ b/drivers/usb/host/ehci-msm.c @@ -0,0 +1,345 @@ +/* ehci-msm.c - HSUSB Host Controller Driver Implementation + * + * Copyright (c) 2008-2010, Code Aurora Forum. All rights reserved. + * + * Partly derived from ehci-fsl.c and ehci-hcd.c + * Copyright (c) 2000-2004 by David Brownell + * Copyright (c) 2005 MontaVista Software + * + * All source code in this file is licensed under the following license except + * where indicated. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. + * + * See the GNU General Public License for more details. + * You should have received a copy of the GNU General Public License + * along with this program; if not, you can find it at http://www.fsf.org + */ + +#include <linux/platform_device.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/pm_runtime.h> + +#include <linux/usb/otg.h> +#include <linux/usb/msm_hsusb_hw.h> + +#define MSM_USB_BASE (hcd->regs) + +static struct otg_transceiver *otg; + +/* + * ehci_run defined in drivers/usb/host/ehci-hcd.c reset the controller and + * the configuration settings in ehci_msm_reset vanish after controller is + * reset. Resetting the controler in ehci_run seems to be un-necessary + * provided HCD reset the controller before calling ehci_run. Most of the HCD + * do but some are not. So this function is same as ehci_run but we don't + * reset the controller here. + */ +static int ehci_msm_run(struct usb_hcd *hcd) +{ + struct ehci_hcd *ehci = hcd_to_ehci(hcd); + u32 temp; + u32 hcc_params; + + hcd->uses_new_polling = 1; + + ehci_writel(ehci, ehci->periodic_dma, &ehci->regs->frame_list); + ehci_writel(ehci, (u32)ehci->async->qh_dma, &ehci->regs->async_next); + + /* + * hcc_params controls whether ehci->regs->segment must (!!!) + * be used; it constrains QH/ITD/SITD and QTD locations. + * pci_pool consistent memory always uses segment zero. + * streaming mappings for I/O buffers, like pci_map_single(), + * can return segments above 4GB, if the device allows. + * + * NOTE: the dma mask is visible through dma_supported(), so + * drivers can pass this info along ... like NETIF_F_HIGHDMA, + * Scsi_Host.highmem_io, and so forth. It's readonly to all + * host side drivers though. + */ + hcc_params = ehci_readl(ehci, &ehci->caps->hcc_params); + if (HCC_64BIT_ADDR(hcc_params)) + ehci_writel(ehci, 0, &ehci->regs->segment); + + /* + * Philips, Intel, and maybe others need CMD_RUN before the + * root hub will detect new devices (why?); NEC doesn't + */ + ehci->command &= ~(CMD_LRESET|CMD_IAAD|CMD_PSE|CMD_ASE|CMD_RESET); + ehci->command |= CMD_RUN; + ehci_writel(ehci, ehci->command, &ehci->regs->command); + dbg_cmd(ehci, "init", ehci->command); + + /* + * Start, enabling full USB 2.0 functionality ... usb 1.1 devices + * are explicitly handed to companion controller(s), so no TT is + * involved with the root hub. (Except where one is integrated, + * and there's no companion controller unless maybe for USB OTG.) + * + * Turning on the CF flag will transfer ownership of all ports + * from the companions to the EHCI controller. If any of the + * companions are in the middle of a port reset at the time, it + * could cause trouble. Write-locking ehci_cf_port_reset_rwsem + * guarantees that no resets are in progress. After we set CF, + * a short delay lets the hardware catch up; new resets shouldn't + * be started before the port switching actions could complete. + */ + down_write(&ehci_cf_port_reset_rwsem); + hcd->state = HC_STATE_RUNNING; + ehci_writel(ehci, FLAG_CF, &ehci->regs->configured_flag); + ehci_readl(ehci, &ehci->regs->command); /* unblock posted writes */ + usleep_range(5000, 5500); + up_write(&ehci_cf_port_reset_rwsem); + ehci->last_periodic_enable = ktime_get_real(); + + temp = HC_VERSION(ehci_readl(ehci, &ehci->caps->hc_capbase)); + ehci_info(ehci, + "USB %x.%x started, EHCI %x.%02x%s\n", + ((ehci->sbrn & 0xf0)>>4), (ehci->sbrn & 0x0f), + temp >> 8, temp & 0xff, + ignore_oc ? ", overcurrent ignored" : ""); + + ehci_writel(ehci, INTR_MASK, + &ehci->regs->intr_enable); /* Turn On Interrupts */ + + /* GRR this is run-once init(), being done every time the HC starts. + * So long as they're part of class devices, we can't do it init() + * since the class device isn't created that early. + */ + create_debug_files(ehci); + create_companion_file(ehci); + + return 0; +} + +static int ehci_msm_reset(struct usb_hcd *hcd) +{ + struct ehci_hcd *ehci = hcd_to_ehci(hcd); + int retval; + + ehci->caps = USB_CAPLENGTH; + ehci->regs = USB_CAPLENGTH + + HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase)); + + /* cache the data to minimize the chip reads*/ + ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params); + + hcd->has_tt = 1; + ehci->sbrn = HCD_USB2; + + /* data structure init */ + retval = ehci_init(hcd); + if (retval) + return retval; + + retval = ehci_reset(ehci); + if (retval) + return retval; + + /* bursts of unspecified length. */ + writel(0, USB_AHBBURST); + /* Use the AHB transactor */ + writel(0, USB_AHBMODE); + /* Disable streaming mode and select host mode */ + writel(0x13, USB_USBMODE); + + ehci_port_power(ehci, 1); + return 0; +} + +static struct hc_driver msm_hc_driver = { + .description = hcd_name, + .product_desc = "Qualcomm On-Chip EHCI Host Controller", + .hcd_priv_size = sizeof(struct ehci_hcd), + + /* + * generic hardware linkage + */ + .irq = ehci_irq, + .flags = HCD_USB2 | HCD_MEMORY, + + .reset = ehci_msm_reset, + .start = ehci_msm_run, + + .stop = ehci_stop, + .shutdown = ehci_shutdown, + + /* + * managing i/o requests and associated device resources + */ + .urb_enqueue = ehci_urb_enqueue, + .urb_dequeue = ehci_urb_dequeue, + .endpoint_disable = ehci_endpoint_disable, + .endpoint_reset = ehci_endpoint_reset, + .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete, + + /* + * scheduling support + */ + .get_frame_number = ehci_get_frame, + + /* + * root hub support + */ + .hub_status_data = ehci_hub_status_data, + .hub_control = ehci_hub_control, + .relinquish_port = ehci_relinquish_port, + .port_handed_over = ehci_port_handed_over, + + /* + * PM support + */ + .bus_suspend = ehci_bus_suspend, + .bus_resume = ehci_bus_resume, +}; + +static int ehci_msm_probe(struct platform_device *pdev) +{ + struct usb_hcd *hcd; + struct resource *res; + int ret; + + dev_dbg(&pdev->dev, "ehci_msm proble\n"); + + hcd = usb_create_hcd(&msm_hc_driver, &pdev->dev, dev_name(&pdev->dev)); + if (!hcd) { + dev_err(&pdev->dev, "Unable to create HCD\n"); + return -ENOMEM; + } + + hcd->irq = platform_get_irq(pdev, 0); + if (hcd->irq < 0) { + dev_err(&pdev->dev, "Unable to get IRQ resource\n"); + ret = hcd->irq; + goto put_hcd; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "Unable to get memory resource\n"); + ret = -ENODEV; + goto put_hcd; + } + + hcd->rsrc_start = res->start; + hcd->rsrc_len = resource_size(res); + hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len); + if (!hcd->regs) { + dev_err(&pdev->dev, "ioremap failed\n"); + ret = -ENOMEM; + goto put_hcd; + } + + /* + * OTG driver takes care of PHY initialization, clock management, + * powering up VBUS, mapping of registers address space and power + * management. + */ + otg = otg_get_transceiver(); + if (!otg) { + dev_err(&pdev->dev, "unable to find transceiver\n"); + ret = -ENODEV; + goto unmap; + } + + ret = otg_set_host(otg, &hcd->self); + if (ret < 0) { + dev_err(&pdev->dev, "unable to register with transceiver\n"); + goto put_transceiver; + } + + device_init_wakeup(&pdev->dev, 1); + /* + * OTG device parent of HCD takes care of putting + * hardware into low power mode. + */ + pm_runtime_no_callbacks(&pdev->dev); + pm_runtime_enable(&pdev->dev); + + return 0; + +put_transceiver: + otg_put_transceiver(otg); +unmap: + iounmap(hcd->regs); +put_hcd: + usb_put_hcd(hcd); + + return ret; +} + +static int __devexit ehci_msm_remove(struct platform_device *pdev) +{ + struct usb_hcd *hcd = platform_get_drvdata(pdev); + + device_init_wakeup(&pdev->dev, 0); + pm_runtime_disable(&pdev->dev); + pm_runtime_set_suspended(&pdev->dev); + + otg_set_host(otg, NULL); + otg_put_transceiver(otg); + + usb_put_hcd(hcd); + + return 0; +} + +#ifdef CONFIG_PM +static int ehci_msm_pm_suspend(struct device *dev) +{ + struct usb_hcd *hcd = dev_get_drvdata(dev); + bool wakeup = device_may_wakeup(dev); + + dev_dbg(dev, "ehci-msm PM suspend\n"); + + /* + * EHCI helper function has also the same check before manipulating + * port wakeup flags. We do check here the same condition before + * calling the same helper function to avoid bringing hardware + * from Low power mode when there is no need for adjusting port + * wakeup flags. + */ + if (hcd->self.root_hub->do_remote_wakeup && !wakeup) { + pm_runtime_resume(dev); + ehci_prepare_ports_for_controller_suspend(hcd_to_ehci(hcd), + wakeup); + } + + return 0; +} + +static int ehci_msm_pm_resume(struct device *dev) +{ + struct usb_hcd *hcd = dev_get_drvdata(dev); + + dev_dbg(dev, "ehci-msm PM resume\n"); + ehci_prepare_ports_for_controller_resume(hcd_to_ehci(hcd)); + + return 0; +} +#else +#define ehci_msm_pm_suspend NULL +#define ehci_msm_pm_resume NULL +#endif + +static const struct dev_pm_ops ehci_msm_dev_pm_ops = { + .suspend = ehci_msm_pm_suspend, + .resume = ehci_msm_pm_resume, +}; + +static struct platform_driver ehci_msm_driver = { + .probe = ehci_msm_probe, + .remove = __devexit_p(ehci_msm_remove), + .driver = { + .name = "msm_hsusb_host", + .pm = &ehci_msm_dev_pm_ops, + }, +}; diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c index bce85055019a..f6e5d44c06b6 100644 --- a/drivers/usb/host/ehci-mxc.c +++ b/drivers/usb/host/ehci-mxc.c @@ -100,6 +100,7 @@ static const struct hc_driver ehci_mxc_hc_driver = { .urb_enqueue = ehci_urb_enqueue, .urb_dequeue = ehci_urb_dequeue, .endpoint_disable = ehci_endpoint_disable, + .endpoint_reset = ehci_endpoint_reset, /* * scheduling support @@ -115,6 +116,8 @@ static const struct hc_driver ehci_mxc_hc_driver = { .bus_resume = ehci_bus_resume, .relinquish_port = ehci_relinquish_port, .port_handed_over = ehci_port_handed_over, + + .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete, }; static int ehci_mxc_drv_probe(struct platform_device *pdev) diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c index 116ae280053a..0374eb47f09b 100644 --- a/drivers/usb/host/ehci-omap.c +++ b/drivers/usb/host/ehci-omap.c @@ -1,11 +1,12 @@ /* - * ehci-omap.c - driver for USBHOST on OMAP 34xx processor + * ehci-omap.c - driver for USBHOST on OMAP3/4 processors * - * Bus Glue for OMAP34xx USBHOST 3 port EHCI controller - * Tested on OMAP3430 ES2.0 SDP + * Bus Glue for the EHCI controllers in OMAP3/4 + * Tested on several OMAP3 boards, and OMAP4 Pandaboard * - * Copyright (C) 2007-2008 Texas Instruments, Inc. + * Copyright (C) 2007-2010 Texas Instruments, Inc. * Author: Vikram Pandita <vikram.pandita@ti.com> + * Author: Anand Gadiyar <gadiyar@ti.com> * * Copyright (C) 2009 Nokia Corporation * Contact: Felipe Balbi <felipe.balbi@nokia.com> @@ -26,11 +27,14 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA * - * TODO (last updated Feb 12, 2010): + * TODO (last updated Nov 21, 2010): * - add kernel-doc * - enable AUTOIDLE * - add suspend/resume * - move workarounds to board-files + * - factor out code common to OHCI + * - add HSIC and TLL support + * - convert to use hwmod and runtime PM */ #include <linux/platform_device.h> @@ -114,6 +118,23 @@ #define OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS (1 << 9) #define OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS (1 << 10) +/* OMAP4-specific defines */ +#define OMAP4_UHH_SYSCONFIG_IDLEMODE_CLEAR (3 << 2) +#define OMAP4_UHH_SYSCONFIG_NOIDLE (1 << 2) + +#define OMAP4_UHH_SYSCONFIG_STDBYMODE_CLEAR (3 << 4) +#define OMAP4_UHH_SYSCONFIG_NOSTDBY (1 << 4) +#define OMAP4_UHH_SYSCONFIG_SOFTRESET (1 << 0) + +#define OMAP4_P1_MODE_CLEAR (3 << 16) +#define OMAP4_P1_MODE_TLL (1 << 16) +#define OMAP4_P1_MODE_HSIC (3 << 16) +#define OMAP4_P2_MODE_CLEAR (3 << 18) +#define OMAP4_P2_MODE_TLL (1 << 18) +#define OMAP4_P2_MODE_HSIC (3 << 18) + +#define OMAP_REV2_TLL_CHANNEL_COUNT 2 + #define OMAP_UHH_DEBUG_CSR (0x44) /* EHCI Register Set */ @@ -127,6 +148,17 @@ #define EHCI_INSNREG05_ULPI_EXTREGADD_SHIFT 8 #define EHCI_INSNREG05_ULPI_WRDATA_SHIFT 0 +/* Values of UHH_REVISION - Note: these are not given in the TRM */ +#define OMAP_EHCI_REV1 0x00000010 /* OMAP3 */ +#define OMAP_EHCI_REV2 0x50700100 /* OMAP4 */ + +#define is_omap_ehci_rev1(x) (x->omap_ehci_rev == OMAP_EHCI_REV1) +#define is_omap_ehci_rev2(x) (x->omap_ehci_rev == OMAP_EHCI_REV2) + +#define is_ehci_phy_mode(x) (x == EHCI_HCD_OMAP_MODE_PHY) +#define is_ehci_tll_mode(x) (x == EHCI_HCD_OMAP_MODE_TLL) +#define is_ehci_hsic_mode(x) (x == EHCI_HCD_OMAP_MODE_HSIC) + /*-------------------------------------------------------------------------*/ static inline void ehci_omap_writel(void __iomem *base, u32 reg, u32 val) @@ -156,10 +188,14 @@ struct ehci_hcd_omap { struct device *dev; struct clk *usbhost_ick; - struct clk *usbhost2_120m_fck; - struct clk *usbhost1_48m_fck; + struct clk *usbhost_hs_fck; + struct clk *usbhost_fs_fck; struct clk *usbtll_fck; struct clk *usbtll_ick; + struct clk *xclk60mhsp1_ck; + struct clk *xclk60mhsp2_ck; + struct clk *utmi_p1_fck; + struct clk *utmi_p2_fck; /* FIXME the following two workarounds are * board specific not silicon-specific so these @@ -176,6 +212,9 @@ struct ehci_hcd_omap { /* phy reset workaround */ int phy_reset; + /* IP revision */ + u32 omap_ehci_rev; + /* desired phy_mode: TLL, PHY */ enum ehci_hcd_omap_mode port_mode[OMAP3_HS_USB_PORTS]; @@ -191,13 +230,14 @@ struct ehci_hcd_omap { /*-------------------------------------------------------------------------*/ -static void omap_usb_utmi_init(struct ehci_hcd_omap *omap, u8 tll_channel_mask) +static void omap_usb_utmi_init(struct ehci_hcd_omap *omap, u8 tll_channel_mask, + u8 tll_channel_count) { unsigned reg; int i; /* Program the 3 TLL channels upfront */ - for (i = 0; i < OMAP_TLL_CHANNEL_COUNT; i++) { + for (i = 0; i < tll_channel_count; i++) { reg = ehci_omap_readl(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i)); /* Disable AutoIdle, BitStuffing and use SDR Mode */ @@ -217,7 +257,7 @@ static void omap_usb_utmi_init(struct ehci_hcd_omap *omap, u8 tll_channel_mask) ehci_omap_writel(omap->tll_base, OMAP_TLL_SHARED_CONF, reg); /* Enable channels now */ - for (i = 0; i < OMAP_TLL_CHANNEL_COUNT; i++) { + for (i = 0; i < tll_channel_count; i++) { reg = ehci_omap_readl(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i)); /* Enable only the reg that is needed */ @@ -286,19 +326,19 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) } clk_enable(omap->usbhost_ick); - omap->usbhost2_120m_fck = clk_get(omap->dev, "usbhost_120m_fck"); - if (IS_ERR(omap->usbhost2_120m_fck)) { - ret = PTR_ERR(omap->usbhost2_120m_fck); + omap->usbhost_hs_fck = clk_get(omap->dev, "hs_fck"); + if (IS_ERR(omap->usbhost_hs_fck)) { + ret = PTR_ERR(omap->usbhost_hs_fck); goto err_host_120m_fck; } - clk_enable(omap->usbhost2_120m_fck); + clk_enable(omap->usbhost_hs_fck); - omap->usbhost1_48m_fck = clk_get(omap->dev, "usbhost_48m_fck"); - if (IS_ERR(omap->usbhost1_48m_fck)) { - ret = PTR_ERR(omap->usbhost1_48m_fck); + omap->usbhost_fs_fck = clk_get(omap->dev, "fs_fck"); + if (IS_ERR(omap->usbhost_fs_fck)) { + ret = PTR_ERR(omap->usbhost_fs_fck); goto err_host_48m_fck; } - clk_enable(omap->usbhost1_48m_fck); + clk_enable(omap->usbhost_fs_fck); if (omap->phy_reset) { /* Refer: ISSUE1 */ @@ -333,6 +373,80 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) } clk_enable(omap->usbtll_ick); + omap->omap_ehci_rev = ehci_omap_readl(omap->uhh_base, + OMAP_UHH_REVISION); + dev_dbg(omap->dev, "OMAP UHH_REVISION 0x%x\n", + omap->omap_ehci_rev); + + /* + * Enable per-port clocks as needed (newer controllers only). + * - External ULPI clock for PHY mode + * - Internal clocks for TLL and HSIC modes (TODO) + */ + if (is_omap_ehci_rev2(omap)) { + switch (omap->port_mode[0]) { + case EHCI_HCD_OMAP_MODE_PHY: + omap->xclk60mhsp1_ck = clk_get(omap->dev, + "xclk60mhsp1_ck"); + if (IS_ERR(omap->xclk60mhsp1_ck)) { + ret = PTR_ERR(omap->xclk60mhsp1_ck); + dev_err(omap->dev, + "Unable to get Port1 ULPI clock\n"); + } + + omap->utmi_p1_fck = clk_get(omap->dev, + "utmi_p1_gfclk"); + if (IS_ERR(omap->utmi_p1_fck)) { + ret = PTR_ERR(omap->utmi_p1_fck); + dev_err(omap->dev, + "Unable to get utmi_p1_fck\n"); + } + + ret = clk_set_parent(omap->utmi_p1_fck, + omap->xclk60mhsp1_ck); + if (ret != 0) { + dev_err(omap->dev, + "Unable to set P1 f-clock\n"); + } + break; + case EHCI_HCD_OMAP_MODE_TLL: + /* TODO */ + default: + break; + } + switch (omap->port_mode[1]) { + case EHCI_HCD_OMAP_MODE_PHY: + omap->xclk60mhsp2_ck = clk_get(omap->dev, + "xclk60mhsp2_ck"); + if (IS_ERR(omap->xclk60mhsp2_ck)) { + ret = PTR_ERR(omap->xclk60mhsp2_ck); + dev_err(omap->dev, + "Unable to get Port2 ULPI clock\n"); + } + + omap->utmi_p2_fck = clk_get(omap->dev, + "utmi_p2_gfclk"); + if (IS_ERR(omap->utmi_p2_fck)) { + ret = PTR_ERR(omap->utmi_p2_fck); + dev_err(omap->dev, + "Unable to get utmi_p2_fck\n"); + } + + ret = clk_set_parent(omap->utmi_p2_fck, + omap->xclk60mhsp2_ck); + if (ret != 0) { + dev_err(omap->dev, + "Unable to set P2 f-clock\n"); + } + break; + case EHCI_HCD_OMAP_MODE_TLL: + /* TODO */ + default: + break; + } + } + + /* perform TLL soft reset, and wait until reset is complete */ ehci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG, OMAP_USBTLL_SYSCONFIG_SOFTRESET); @@ -360,12 +474,20 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) /* Put UHH in NoIdle/NoStandby mode */ reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSCONFIG); - reg |= (OMAP_UHH_SYSCONFIG_ENAWAKEUP - | OMAP_UHH_SYSCONFIG_SIDLEMODE - | OMAP_UHH_SYSCONFIG_CACTIVITY - | OMAP_UHH_SYSCONFIG_MIDLEMODE); - reg &= ~OMAP_UHH_SYSCONFIG_AUTOIDLE; + if (is_omap_ehci_rev1(omap)) { + reg |= (OMAP_UHH_SYSCONFIG_ENAWAKEUP + | OMAP_UHH_SYSCONFIG_SIDLEMODE + | OMAP_UHH_SYSCONFIG_CACTIVITY + | OMAP_UHH_SYSCONFIG_MIDLEMODE); + reg &= ~OMAP_UHH_SYSCONFIG_AUTOIDLE; + + } else if (is_omap_ehci_rev2(omap)) { + reg &= ~OMAP4_UHH_SYSCONFIG_IDLEMODE_CLEAR; + reg |= OMAP4_UHH_SYSCONFIG_NOIDLE; + reg &= ~OMAP4_UHH_SYSCONFIG_STDBYMODE_CLEAR; + reg |= OMAP4_UHH_SYSCONFIG_NOSTDBY; + } ehci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG, reg); reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_HOSTCONFIG); @@ -376,40 +498,56 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) | OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN); reg &= ~OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN; - if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_UNKNOWN) - reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS; - if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_UNKNOWN) - reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS; - if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_UNKNOWN) - reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS; - - /* Bypass the TLL module for PHY mode operation */ - if (cpu_is_omap3430() && (omap_rev() <= OMAP3430_REV_ES2_1)) { - dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1\n"); - if ((omap->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY) || - (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY) || - (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_PHY)) - reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_BYPASS; - else - reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS; - } else { - dev_dbg(omap->dev, "OMAP3 ES version > ES2.1\n"); - if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY) - reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS; - else if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL) - reg |= OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS; - - if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY) - reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS; - else if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_TLL) - reg |= OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS; - - if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_PHY) - reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS; - else if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_TLL) - reg |= OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS; + if (is_omap_ehci_rev1(omap)) { + if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_UNKNOWN) + reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS; + if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_UNKNOWN) + reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS; + if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_UNKNOWN) + reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS; + + /* Bypass the TLL module for PHY mode operation */ + if (cpu_is_omap3430() && (omap_rev() <= OMAP3430_REV_ES2_1)) { + dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1\n"); + if (is_ehci_phy_mode(omap->port_mode[0]) || + is_ehci_phy_mode(omap->port_mode[1]) || + is_ehci_phy_mode(omap->port_mode[2])) + reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_BYPASS; + else + reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS; + } else { + dev_dbg(omap->dev, "OMAP3 ES version > ES2.1\n"); + if (is_ehci_phy_mode(omap->port_mode[0])) + reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS; + else if (is_ehci_tll_mode(omap->port_mode[0])) + reg |= OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS; + + if (is_ehci_phy_mode(omap->port_mode[1])) + reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS; + else if (is_ehci_tll_mode(omap->port_mode[1])) + reg |= OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS; + + if (is_ehci_phy_mode(omap->port_mode[2])) + reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS; + else if (is_ehci_tll_mode(omap->port_mode[2])) + reg |= OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS; + } + } else if (is_omap_ehci_rev2(omap)) { + /* Clear port mode fields for PHY mode*/ + reg &= ~OMAP4_P1_MODE_CLEAR; + reg &= ~OMAP4_P2_MODE_CLEAR; + + if (is_ehci_tll_mode(omap->port_mode[0])) + reg |= OMAP4_P1_MODE_TLL; + else if (is_ehci_hsic_mode(omap->port_mode[0])) + reg |= OMAP4_P1_MODE_HSIC; + if (is_ehci_tll_mode(omap->port_mode[1])) + reg |= OMAP4_P2_MODE_TLL; + else if (is_ehci_hsic_mode(omap->port_mode[1])) + reg |= OMAP4_P2_MODE_HSIC; } + ehci_omap_writel(omap->uhh_base, OMAP_UHH_HOSTCONFIG, reg); dev_dbg(omap->dev, "UHH setup done, uhh_hostconfig=%x\n", reg); @@ -438,7 +576,7 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) tll_ch_mask |= OMAP_TLL_CHANNEL_3_EN_MASK; /* Enable UTMI mode for required TLL channels */ - omap_usb_utmi_init(omap, tll_ch_mask); + omap_usb_utmi_init(omap, tll_ch_mask, OMAP_TLL_CHANNEL_COUNT); } if (omap->phy_reset) { @@ -464,6 +602,14 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) return 0; err_sys_status: + clk_disable(omap->utmi_p2_fck); + clk_put(omap->utmi_p2_fck); + clk_disable(omap->xclk60mhsp2_ck); + clk_put(omap->xclk60mhsp2_ck); + clk_disable(omap->utmi_p1_fck); + clk_put(omap->utmi_p1_fck); + clk_disable(omap->xclk60mhsp1_ck); + clk_put(omap->xclk60mhsp1_ck); clk_disable(omap->usbtll_ick); clk_put(omap->usbtll_ick); @@ -472,8 +618,8 @@ err_tll_ick: clk_put(omap->usbtll_fck); err_tll_fck: - clk_disable(omap->usbhost1_48m_fck); - clk_put(omap->usbhost1_48m_fck); + clk_disable(omap->usbhost_fs_fck); + clk_put(omap->usbhost_fs_fck); if (omap->phy_reset) { if (gpio_is_valid(omap->reset_gpio_port[0])) @@ -484,8 +630,8 @@ err_tll_fck: } err_host_48m_fck: - clk_disable(omap->usbhost2_120m_fck); - clk_put(omap->usbhost2_120m_fck); + clk_disable(omap->usbhost_hs_fck); + clk_put(omap->usbhost_hs_fck); err_host_120m_fck: clk_disable(omap->usbhost_ick); @@ -503,6 +649,8 @@ static void omap_stop_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) /* Reset OMAP modules for insmod/rmmod to work */ ehci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG, + is_omap_ehci_rev2(omap) ? + OMAP4_UHH_SYSCONFIG_SOFTRESET : OMAP_UHH_SYSCONFIG_SOFTRESET); while (!(ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS) & (1 << 0))) { @@ -550,16 +698,16 @@ static void omap_stop_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) omap->usbhost_ick = NULL; } - if (omap->usbhost1_48m_fck != NULL) { - clk_disable(omap->usbhost1_48m_fck); - clk_put(omap->usbhost1_48m_fck); - omap->usbhost1_48m_fck = NULL; + if (omap->usbhost_fs_fck != NULL) { + clk_disable(omap->usbhost_fs_fck); + clk_put(omap->usbhost_fs_fck); + omap->usbhost_fs_fck = NULL; } - if (omap->usbhost2_120m_fck != NULL) { - clk_disable(omap->usbhost2_120m_fck); - clk_put(omap->usbhost2_120m_fck); - omap->usbhost2_120m_fck = NULL; + if (omap->usbhost_hs_fck != NULL) { + clk_disable(omap->usbhost_hs_fck); + clk_put(omap->usbhost_hs_fck); + omap->usbhost_hs_fck = NULL; } if (omap->usbtll_ick != NULL) { @@ -568,6 +716,32 @@ static void omap_stop_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) omap->usbtll_ick = NULL; } + if (is_omap_ehci_rev2(omap)) { + if (omap->xclk60mhsp1_ck != NULL) { + clk_disable(omap->xclk60mhsp1_ck); + clk_put(omap->xclk60mhsp1_ck); + omap->xclk60mhsp1_ck = NULL; + } + + if (omap->utmi_p1_fck != NULL) { + clk_disable(omap->utmi_p1_fck); + clk_put(omap->utmi_p1_fck); + omap->utmi_p1_fck = NULL; + } + + if (omap->xclk60mhsp2_ck != NULL) { + clk_disable(omap->xclk60mhsp2_ck); + clk_put(omap->xclk60mhsp2_ck); + omap->xclk60mhsp2_ck = NULL; + } + + if (omap->utmi_p2_fck != NULL) { + clk_disable(omap->utmi_p2_fck); + clk_put(omap->utmi_p2_fck); + omap->utmi_p2_fck = NULL; + } + } + if (omap->phy_reset) { if (gpio_is_valid(omap->reset_gpio_port[0])) gpio_free(omap->reset_gpio_port[0]); diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c index 655f3c9f88bf..76179c39c0e3 100644 --- a/drivers/usb/host/ehci-pci.c +++ b/drivers/usb/host/ehci-pci.c @@ -22,6 +22,9 @@ #error "This file is PCI bus glue. CONFIG_PCI must be defined." #endif +/* defined here to avoid adding to pci_ids.h for single instance use */ +#define PCI_DEVICE_ID_INTEL_CE4100_USB 0x2e70 + /*-------------------------------------------------------------------------*/ /* called after powerup, by probe or system-pm "wakeup" */ @@ -41,6 +44,35 @@ static int ehci_pci_reinit(struct ehci_hcd *ehci, struct pci_dev *pdev) return 0; } +static int ehci_quirk_amd_SB800(struct ehci_hcd *ehci) +{ + struct pci_dev *amd_smbus_dev; + u8 rev = 0; + + amd_smbus_dev = pci_get_device(PCI_VENDOR_ID_ATI, 0x4385, NULL); + if (!amd_smbus_dev) + return 0; + + pci_read_config_byte(amd_smbus_dev, PCI_REVISION_ID, &rev); + if (rev < 0x40) { + pci_dev_put(amd_smbus_dev); + amd_smbus_dev = NULL; + return 0; + } + + if (!amd_nb_dev) + amd_nb_dev = pci_get_device(PCI_VENDOR_ID_AMD, 0x1510, NULL); + if (!amd_nb_dev) + ehci_err(ehci, "QUIRK: unable to get AMD NB device\n"); + + ehci_info(ehci, "QUIRK: Enable AMD SB800 L1 fix\n"); + + pci_dev_put(amd_smbus_dev); + amd_smbus_dev = NULL; + + return 1; +} + /* called during probe() after chip reset completes */ static int ehci_pci_setup(struct usb_hcd *hcd) { @@ -99,6 +131,9 @@ static int ehci_pci_setup(struct usb_hcd *hcd) /* cache this readonly data; minimize chip reads */ ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params); + if (ehci_quirk_amd_SB800(ehci)) + ehci->amd_l1_fix = 1; + retval = ehci_halt(ehci); if (retval) return retval; @@ -137,6 +172,10 @@ static int ehci_pci_setup(struct usb_hcd *hcd) ehci_info(ehci, "disable lpm for langwell/penwell\n"); ehci->has_lpm = 0; } + if (pdev->device == PCI_DEVICE_ID_INTEL_CE4100_USB) { + hcd->has_tt = 1; + tdi_reset(ehci); + } break; case PCI_VENDOR_ID_TDI: if (pdev->device == PCI_DEVICE_ID_TDI_EHCI) { diff --git a/drivers/usb/host/ehci-sched.c b/drivers/usb/host/ehci-sched.c index d9f78eb26572..aa46f57f9ec8 100644 --- a/drivers/usb/host/ehci-sched.c +++ b/drivers/usb/host/ehci-sched.c @@ -1590,6 +1590,63 @@ itd_link (struct ehci_hcd *ehci, unsigned frame, struct ehci_itd *itd) *hw_p = cpu_to_hc32(ehci, itd->itd_dma | Q_TYPE_ITD); } +#define AB_REG_BAR_LOW 0xe0 +#define AB_REG_BAR_HIGH 0xe1 +#define AB_INDX(addr) ((addr) + 0x00) +#define AB_DATA(addr) ((addr) + 0x04) +#define NB_PCIE_INDX_ADDR 0xe0 +#define NB_PCIE_INDX_DATA 0xe4 +#define NB_PIF0_PWRDOWN_0 0x01100012 +#define NB_PIF0_PWRDOWN_1 0x01100013 + +static void ehci_quirk_amd_L1(struct ehci_hcd *ehci, int disable) +{ + u32 addr, addr_low, addr_high, val; + + outb_p(AB_REG_BAR_LOW, 0xcd6); + addr_low = inb_p(0xcd7); + outb_p(AB_REG_BAR_HIGH, 0xcd6); + addr_high = inb_p(0xcd7); + addr = addr_high << 8 | addr_low; + outl_p(0x30, AB_INDX(addr)); + outl_p(0x40, AB_DATA(addr)); + outl_p(0x34, AB_INDX(addr)); + val = inl_p(AB_DATA(addr)); + + if (disable) { + val &= ~0x8; + val |= (1 << 4) | (1 << 9); + } else { + val |= 0x8; + val &= ~((1 << 4) | (1 << 9)); + } + outl_p(val, AB_DATA(addr)); + + if (amd_nb_dev) { + addr = NB_PIF0_PWRDOWN_0; + pci_write_config_dword(amd_nb_dev, NB_PCIE_INDX_ADDR, addr); + pci_read_config_dword(amd_nb_dev, NB_PCIE_INDX_DATA, &val); + if (disable) + val &= ~(0x3f << 7); + else + val |= 0x3f << 7; + + pci_write_config_dword(amd_nb_dev, NB_PCIE_INDX_DATA, val); + + addr = NB_PIF0_PWRDOWN_1; + pci_write_config_dword(amd_nb_dev, NB_PCIE_INDX_ADDR, addr); + pci_read_config_dword(amd_nb_dev, NB_PCIE_INDX_DATA, &val); + if (disable) + val &= ~(0x3f << 7); + else + val |= 0x3f << 7; + + pci_write_config_dword(amd_nb_dev, NB_PCIE_INDX_DATA, val); + } + + return; +} + /* fit urb's itds into the selected schedule slot; activate as needed */ static int itd_link_urb ( @@ -1616,6 +1673,12 @@ itd_link_urb ( urb->interval, next_uframe >> 3, next_uframe & 0x7); } + + if (ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs == 0) { + if (ehci->amd_l1_fix == 1) + ehci_quirk_amd_L1(ehci, 1); + } + ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs++; /* fill iTDs uframe by uframe */ @@ -1740,6 +1803,11 @@ itd_complete ( (void) disable_periodic(ehci); ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs--; + if (ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs == 0) { + if (ehci->amd_l1_fix == 1) + ehci_quirk_amd_L1(ehci, 0); + } + if (unlikely(list_is_singular(&stream->td_list))) { ehci_to_hcd(ehci)->self.bandwidth_allocated -= stream->bandwidth; @@ -2025,6 +2093,12 @@ sitd_link_urb ( (next_uframe >> 3) & (ehci->periodic_size - 1), stream->interval, hc32_to_cpu(ehci, stream->splits)); } + + if (ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs == 0) { + if (ehci->amd_l1_fix == 1) + ehci_quirk_amd_L1(ehci, 1); + } + ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs++; /* fill sITDs frame by frame */ @@ -2125,6 +2199,11 @@ sitd_complete ( (void) disable_periodic(ehci); ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs--; + if (ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs == 0) { + if (ehci->amd_l1_fix == 1) + ehci_quirk_amd_L1(ehci, 0); + } + if (list_is_singular(&stream->td_list)) { ehci_to_hcd(ehci)->self.bandwidth_allocated -= stream->bandwidth; diff --git a/drivers/usb/host/ehci-sh.c b/drivers/usb/host/ehci-sh.c new file mode 100644 index 000000000000..595f70f42b52 --- /dev/null +++ b/drivers/usb/host/ehci-sh.c @@ -0,0 +1,243 @@ +/* + * SuperH EHCI host controller driver + * + * Copyright (C) 2010 Paul Mundt + * + * Based on ohci-sh.c and ehci-atmel.c. + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + */ +#include <linux/platform_device.h> +#include <linux/clk.h> + +struct ehci_sh_priv { + struct clk *iclk, *fclk; + struct usb_hcd *hcd; +}; + +static int ehci_sh_reset(struct usb_hcd *hcd) +{ + struct ehci_hcd *ehci = hcd_to_ehci(hcd); + int ret; + + ehci->caps = hcd->regs; + ehci->regs = hcd->regs + HC_LENGTH(ehci_readl(ehci, + &ehci->caps->hc_capbase)); + + dbg_hcs_params(ehci, "reset"); + dbg_hcc_params(ehci, "reset"); + + ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params); + + ret = ehci_halt(ehci); + if (unlikely(ret)) + return ret; + + ret = ehci_init(hcd); + if (unlikely(ret)) + return ret; + + ehci->sbrn = 0x20; + + ehci_reset(ehci); + ehci_port_power(ehci, 0); + + return ret; +} + +static const struct hc_driver ehci_sh_hc_driver = { + .description = hcd_name, + .product_desc = "SuperH EHCI", + .hcd_priv_size = sizeof(struct ehci_hcd), + + /* + * generic hardware linkage + */ + .irq = ehci_irq, + .flags = HCD_USB2 | HCD_MEMORY, + + /* + * basic lifecycle operations + */ + .reset = ehci_sh_reset, + .start = ehci_run, + .stop = ehci_stop, + .shutdown = ehci_shutdown, + + /* + * managing i/o requests and associated device resources + */ + .urb_enqueue = ehci_urb_enqueue, + .urb_dequeue = ehci_urb_dequeue, + .endpoint_disable = ehci_endpoint_disable, + .endpoint_reset = ehci_endpoint_reset, + + /* + * scheduling support + */ + .get_frame_number = ehci_get_frame, + + /* + * root hub support + */ + .hub_status_data = ehci_hub_status_data, + .hub_control = ehci_hub_control, + +#ifdef CONFIG_PM + .bus_suspend = ehci_bus_suspend, + .bus_resume = ehci_bus_resume, +#endif + + .relinquish_port = ehci_relinquish_port, + .port_handed_over = ehci_port_handed_over, + .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete, +}; + +static int ehci_hcd_sh_probe(struct platform_device *pdev) +{ + const struct hc_driver *driver = &ehci_sh_hc_driver; + struct resource *res; + struct ehci_sh_priv *priv; + struct usb_hcd *hcd; + int irq, ret; + + if (usb_disabled()) + return -ENODEV; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, + "Found HC with no register addr. Check %s setup!\n", + dev_name(&pdev->dev)); + ret = -ENODEV; + goto fail_create_hcd; + } + + irq = platform_get_irq(pdev, 0); + if (irq <= 0) { + dev_err(&pdev->dev, + "Found HC with no IRQ. Check %s setup!\n", + dev_name(&pdev->dev)); + ret = -ENODEV; + goto fail_create_hcd; + } + + /* initialize hcd */ + hcd = usb_create_hcd(&ehci_sh_hc_driver, &pdev->dev, + dev_name(&pdev->dev)); + if (!hcd) { + ret = -ENOMEM; + goto fail_create_hcd; + } + + hcd->rsrc_start = res->start; + hcd->rsrc_len = resource_size(res); + + if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, + driver->description)) { + dev_dbg(&pdev->dev, "controller already in use\n"); + ret = -EBUSY; + goto fail_request_resource; + } + + hcd->regs = ioremap_nocache(hcd->rsrc_start, hcd->rsrc_len); + if (hcd->regs == NULL) { + dev_dbg(&pdev->dev, "error mapping memory\n"); + ret = -ENXIO; + goto fail_ioremap; + } + + priv = kmalloc(sizeof(struct ehci_sh_priv), GFP_KERNEL); + if (!priv) { + dev_dbg(&pdev->dev, "error allocating priv data\n"); + ret = -ENOMEM; + goto fail_alloc; + } + + /* These are optional, we don't care if they fail */ + priv->fclk = clk_get(&pdev->dev, "usb_fck"); + if (IS_ERR(priv->fclk)) + priv->fclk = NULL; + + priv->iclk = clk_get(&pdev->dev, "usb_ick"); + if (IS_ERR(priv->iclk)) + priv->iclk = NULL; + + clk_enable(priv->fclk); + clk_enable(priv->iclk); + + ret = usb_add_hcd(hcd, irq, IRQF_DISABLED | IRQF_SHARED); + if (ret != 0) { + dev_err(&pdev->dev, "Failed to add hcd"); + goto fail_add_hcd; + } + + priv->hcd = hcd; + platform_set_drvdata(pdev, priv); + + return ret; + +fail_add_hcd: + clk_disable(priv->iclk); + clk_disable(priv->fclk); + + clk_put(priv->iclk); + clk_put(priv->fclk); + + kfree(priv); +fail_alloc: + iounmap(hcd->regs); +fail_ioremap: + release_mem_region(hcd->rsrc_start, hcd->rsrc_len); +fail_request_resource: + usb_put_hcd(hcd); +fail_create_hcd: + dev_err(&pdev->dev, "init %s fail, %d\n", dev_name(&pdev->dev), ret); + + return ret; +} + +static int __exit ehci_hcd_sh_remove(struct platform_device *pdev) +{ + struct ehci_sh_priv *priv = platform_get_drvdata(pdev); + struct usb_hcd *hcd = priv->hcd; + + usb_remove_hcd(hcd); + iounmap(hcd->regs); + release_mem_region(hcd->rsrc_start, hcd->rsrc_len); + usb_put_hcd(hcd); + platform_set_drvdata(pdev, NULL); + + clk_disable(priv->fclk); + clk_disable(priv->iclk); + + clk_put(priv->fclk); + clk_put(priv->iclk); + + kfree(priv); + + return 0; +} + +static void ehci_hcd_sh_shutdown(struct platform_device *pdev) +{ + struct ehci_sh_priv *priv = platform_get_drvdata(pdev); + struct usb_hcd *hcd = priv->hcd; + + if (hcd->driver->shutdown) + hcd->driver->shutdown(hcd); +} + +static struct platform_driver ehci_hcd_sh_driver = { + .probe = ehci_hcd_sh_probe, + .remove = __exit_p(ehci_hcd_sh_remove), + .shutdown = ehci_hcd_sh_shutdown, + .driver = { + .name = "sh_ehci", + .owner = THIS_MODULE, + }, +}; + +MODULE_ALIAS("platform:sh_ehci"); diff --git a/drivers/usb/host/ehci-spear.c b/drivers/usb/host/ehci-spear.c new file mode 100644 index 000000000000..75c00873443d --- /dev/null +++ b/drivers/usb/host/ehci-spear.c @@ -0,0 +1,212 @@ +/* +* Driver for EHCI HCD on SPEAR SOC +* +* Copyright (C) 2010 ST Micro Electronics, +* Deepak Sikri <deepak.sikri@st.com> +* +* Based on various ehci-*.c drivers +* +* This file is subject to the terms and conditions of the GNU General Public +* License. See the file COPYING in the main directory of this archive for +* more details. +*/ + +#include <linux/platform_device.h> +#include <linux/clk.h> + +struct spear_ehci { + struct ehci_hcd ehci; + struct clk *clk; +}; + +#define to_spear_ehci(hcd) (struct spear_ehci *)hcd_to_ehci(hcd) + +static void spear_start_ehci(struct spear_ehci *ehci) +{ + clk_enable(ehci->clk); +} + +static void spear_stop_ehci(struct spear_ehci *ehci) +{ + clk_disable(ehci->clk); +} + +static int ehci_spear_setup(struct usb_hcd *hcd) +{ + struct ehci_hcd *ehci = hcd_to_ehci(hcd); + int retval = 0; + + /* registers start at offset 0x0 */ + ehci->caps = hcd->regs; + ehci->regs = hcd->regs + HC_LENGTH(ehci_readl(ehci, + &ehci->caps->hc_capbase)); + /* cache this readonly data; minimize chip reads */ + ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params); + retval = ehci_halt(ehci); + if (retval) + return retval; + + retval = ehci_init(hcd); + if (retval) + return retval; + + ehci_reset(ehci); + ehci_port_power(ehci, 0); + + return retval; +} + +static const struct hc_driver ehci_spear_hc_driver = { + .description = hcd_name, + .product_desc = "SPEAr EHCI", + .hcd_priv_size = sizeof(struct spear_ehci), + + /* generic hardware linkage */ + .irq = ehci_irq, + .flags = HCD_MEMORY | HCD_USB2, + + /* basic lifecycle operations */ + .reset = ehci_spear_setup, + .start = ehci_run, + .stop = ehci_stop, + .shutdown = ehci_shutdown, + + /* managing i/o requests and associated device resources */ + .urb_enqueue = ehci_urb_enqueue, + .urb_dequeue = ehci_urb_dequeue, + .endpoint_disable = ehci_endpoint_disable, + .endpoint_reset = ehci_endpoint_reset, + + /* scheduling support */ + .get_frame_number = ehci_get_frame, + + /* root hub support */ + .hub_status_data = ehci_hub_status_data, + .hub_control = ehci_hub_control, + .bus_suspend = ehci_bus_suspend, + .bus_resume = ehci_bus_resume, + .relinquish_port = ehci_relinquish_port, + .port_handed_over = ehci_port_handed_over, + .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete, +}; + +static int spear_ehci_hcd_drv_probe(struct platform_device *pdev) +{ + struct usb_hcd *hcd ; + struct spear_ehci *ehci; + struct resource *res; + struct clk *usbh_clk; + const struct hc_driver *driver = &ehci_spear_hc_driver; + int *pdata = pdev->dev.platform_data; + int irq, retval; + char clk_name[20] = "usbh_clk"; + + if (pdata == NULL) + return -EFAULT; + + if (usb_disabled()) + return -ENODEV; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + retval = irq; + goto fail_irq_get; + } + + if (*pdata >= 0) + sprintf(clk_name, "usbh.%01d_clk", *pdata); + + usbh_clk = clk_get(NULL, clk_name); + if (IS_ERR(usbh_clk)) { + dev_err(&pdev->dev, "Error getting interface clock\n"); + retval = PTR_ERR(usbh_clk); + goto fail_get_usbh_clk; + } + + hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev)); + if (!hcd) { + retval = -ENOMEM; + goto fail_create_hcd; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + retval = -ENODEV; + goto fail_request_resource; + } + + hcd->rsrc_start = res->start; + hcd->rsrc_len = resource_size(res); + if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, + driver->description)) { + retval = -EBUSY; + goto fail_request_resource; + } + + hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len); + if (hcd->regs == NULL) { + dev_dbg(&pdev->dev, "error mapping memory\n"); + retval = -ENOMEM; + goto fail_ioremap; + } + + ehci = (struct spear_ehci *)hcd_to_ehci(hcd); + ehci->clk = usbh_clk; + + spear_start_ehci(ehci); + retval = usb_add_hcd(hcd, irq, IRQF_SHARED | IRQF_DISABLED); + if (retval) + goto fail_add_hcd; + + return retval; + +fail_add_hcd: + spear_stop_ehci(ehci); + iounmap(hcd->regs); +fail_ioremap: + release_mem_region(hcd->rsrc_start, hcd->rsrc_len); +fail_request_resource: + usb_put_hcd(hcd); +fail_create_hcd: + clk_put(usbh_clk); +fail_get_usbh_clk: +fail_irq_get: + dev_err(&pdev->dev, "init fail, %d\n", retval); + + return retval ; +} + +static int spear_ehci_hcd_drv_remove(struct platform_device *pdev) +{ + struct usb_hcd *hcd = platform_get_drvdata(pdev); + struct spear_ehci *ehci_p = to_spear_ehci(hcd); + + if (!hcd) + return 0; + if (in_interrupt()) + BUG(); + usb_remove_hcd(hcd); + + if (ehci_p->clk) + spear_stop_ehci(ehci_p); + iounmap(hcd->regs); + release_mem_region(hcd->rsrc_start, hcd->rsrc_len); + usb_put_hcd(hcd); + + if (ehci_p->clk) + clk_put(ehci_p->clk); + + return 0; +} + +static struct platform_driver spear_ehci_hcd_driver = { + .probe = spear_ehci_hcd_drv_probe, + .remove = spear_ehci_hcd_drv_remove, + .shutdown = usb_hcd_platform_shutdown, + .driver = { + .name = "spear-ehci", + .bus = &platform_bus_type + } +}; + +MODULE_ALIAS("platform:spear-ehci"); diff --git a/drivers/usb/host/ehci-vt8500.c b/drivers/usb/host/ehci-vt8500.c new file mode 100644 index 000000000000..20168062035a --- /dev/null +++ b/drivers/usb/host/ehci-vt8500.c @@ -0,0 +1,172 @@ +/* + * drivers/usb/host/ehci-vt8500.c + * + * Copyright (C) 2010 Alexey Charkov <alchark@gmail.com> + * + * Based on ehci-au1xxx.c + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/platform_device.h> + +static int ehci_update_device(struct usb_hcd *hcd, struct usb_device *udev) +{ + struct ehci_hcd *ehci = hcd_to_ehci(hcd); + int rc = 0; + + if (!udev->parent) /* udev is root hub itself, impossible */ + rc = -1; + /* we only support lpm device connected to root hub yet */ + if (ehci->has_lpm && !udev->parent->parent) { + rc = ehci_lpm_set_da(ehci, udev->devnum, udev->portnum); + if (!rc) + rc = ehci_lpm_check(ehci, udev->portnum); + } + return rc; +} + +static const struct hc_driver vt8500_ehci_hc_driver = { + .description = hcd_name, + .product_desc = "VT8500 EHCI", + .hcd_priv_size = sizeof(struct ehci_hcd), + + /* + * generic hardware linkage + */ + .irq = ehci_irq, + .flags = HCD_MEMORY | HCD_USB2, + + /* + * basic lifecycle operations + */ + .reset = ehci_init, + .start = ehci_run, + .stop = ehci_stop, + .shutdown = ehci_shutdown, + + /* + * managing i/o requests and associated device resources + */ + .urb_enqueue = ehci_urb_enqueue, + .urb_dequeue = ehci_urb_dequeue, + .endpoint_disable = ehci_endpoint_disable, + .endpoint_reset = ehci_endpoint_reset, + + /* + * scheduling support + */ + .get_frame_number = ehci_get_frame, + + /* + * root hub support + */ + .hub_status_data = ehci_hub_status_data, + .hub_control = ehci_hub_control, + .bus_suspend = ehci_bus_suspend, + .bus_resume = ehci_bus_resume, + .relinquish_port = ehci_relinquish_port, + .port_handed_over = ehci_port_handed_over, + + /* + * call back when device connected and addressed + */ + .update_device = ehci_update_device, + + .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete, +}; + +static int vt8500_ehci_drv_probe(struct platform_device *pdev) +{ + struct usb_hcd *hcd; + struct ehci_hcd *ehci; + struct resource *res; + int ret; + + if (usb_disabled()) + return -ENODEV; + + if (pdev->resource[1].flags != IORESOURCE_IRQ) { + pr_debug("resource[1] is not IORESOURCE_IRQ"); + return -ENOMEM; + } + hcd = usb_create_hcd(&vt8500_ehci_hc_driver, &pdev->dev, "VT8500"); + if (!hcd) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + hcd->rsrc_start = res->start; + hcd->rsrc_len = resource_size(res); + + if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) { + pr_debug("request_mem_region failed"); + ret = -EBUSY; + goto err1; + } + + hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len); + if (!hcd->regs) { + pr_debug("ioremap failed"); + ret = -ENOMEM; + goto err2; + } + + ehci = hcd_to_ehci(hcd); + ehci->caps = hcd->regs; + ehci->regs = hcd->regs + HC_LENGTH(readl(&ehci->caps->hc_capbase)); + + dbg_hcs_params(ehci, "reset"); + dbg_hcc_params(ehci, "reset"); + + /* cache this readonly data; minimize chip reads */ + ehci->hcs_params = readl(&ehci->caps->hcs_params); + + ehci_port_power(ehci, 1); + + ret = usb_add_hcd(hcd, pdev->resource[1].start, + IRQF_DISABLED | IRQF_SHARED); + if (ret == 0) { + platform_set_drvdata(pdev, hcd); + return ret; + } + + iounmap(hcd->regs); +err2: + release_mem_region(hcd->rsrc_start, hcd->rsrc_len); +err1: + usb_put_hcd(hcd); + return ret; +} + +static int vt8500_ehci_drv_remove(struct platform_device *pdev) +{ + struct usb_hcd *hcd = platform_get_drvdata(pdev); + + usb_remove_hcd(hcd); + iounmap(hcd->regs); + release_mem_region(hcd->rsrc_start, hcd->rsrc_len); + usb_put_hcd(hcd); + platform_set_drvdata(pdev, NULL); + + return 0; +} + +static struct platform_driver vt8500_ehci_driver = { + .probe = vt8500_ehci_drv_probe, + .remove = vt8500_ehci_drv_remove, + .shutdown = usb_hcd_platform_shutdown, + .driver = { + .name = "vt8500-ehci", + .owner = THIS_MODULE, + } +}; + +MODULE_ALIAS("platform:vt8500-ehci"); diff --git a/drivers/usb/host/ehci-w90x900.c b/drivers/usb/host/ehci-w90x900.c index cfa21ea20f82..6bc35809a5c6 100644 --- a/drivers/usb/host/ehci-w90x900.c +++ b/drivers/usb/host/ehci-w90x900.c @@ -130,6 +130,7 @@ static const struct hc_driver ehci_w90x900_hc_driver = { .urb_enqueue = ehci_urb_enqueue, .urb_dequeue = ehci_urb_dequeue, .endpoint_disable = ehci_endpoint_disable, + .endpoint_reset = ehci_endpoint_reset, /* * scheduling support @@ -147,6 +148,8 @@ static const struct hc_driver ehci_w90x900_hc_driver = { #endif .relinquish_port = ehci_relinquish_port, .port_handed_over = ehci_port_handed_over, + + .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete, }; static int __devinit ehci_w90x900_probe(struct platform_device *pdev) diff --git a/drivers/usb/host/ehci-xilinx-of.c b/drivers/usb/host/ehci-xilinx-of.c index 6c8076ad821d..e8f4f36fdf0b 100644 --- a/drivers/usb/host/ehci-xilinx-of.c +++ b/drivers/usb/host/ehci-xilinx-of.c @@ -117,6 +117,7 @@ static const struct hc_driver ehci_xilinx_of_hc_driver = { .urb_enqueue = ehci_urb_enqueue, .urb_dequeue = ehci_urb_dequeue, .endpoint_disable = ehci_endpoint_disable, + .endpoint_reset = ehci_endpoint_reset, /* * scheduling support diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h index ba8eab366b82..799ac16a54b4 100644 --- a/drivers/usb/host/ehci.h +++ b/drivers/usb/host/ehci.h @@ -131,6 +131,7 @@ struct ehci_hcd { /* one per controller */ unsigned has_amcc_usb23:1; unsigned need_io_watchdog:1; unsigned broken_periodic:1; + unsigned amd_l1_fix:1; unsigned fs_i_thresh:1; /* Intel iso scheduling */ unsigned use_dummy_qh:1; /* AMD Frame List table quirk*/ diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c index 5179acb7aa2f..4a4a4f025385 100644 --- a/drivers/usb/host/ohci-hcd.c +++ b/drivers/usb/host/ohci-hcd.c @@ -1081,6 +1081,11 @@ MODULE_LICENSE ("GPL"); #define OF_PLATFORM_DRIVER ohci_hcd_ppc_of_driver #endif +#ifdef CONFIG_PLAT_SPEAR +#include "ohci-spear.c" +#define PLATFORM_DRIVER spear_ohci_hcd_driver +#endif + #ifdef CONFIG_PPC_PS3 #include "ohci-ps3.c" #define PS3_SYSTEM_BUS_DRIVER ps3_ohci_driver diff --git a/drivers/usb/host/ohci-sh.c b/drivers/usb/host/ohci-sh.c index 0b35d22cc70e..f47867ff78c7 100644 --- a/drivers/usb/host/ohci-sh.c +++ b/drivers/usb/host/ohci-sh.c @@ -109,7 +109,7 @@ static int ohci_hcd_sh_probe(struct platform_device *pdev) hcd->regs = (void __iomem *)res->start; hcd->rsrc_start = res->start; hcd->rsrc_len = resource_size(res); - ret = usb_add_hcd(hcd, irq, IRQF_DISABLED); + ret = usb_add_hcd(hcd, irq, IRQF_DISABLED | IRQF_SHARED); if (ret != 0) { err("Failed to add hcd"); usb_put_hcd(hcd); diff --git a/drivers/usb/host/ohci-spear.c b/drivers/usb/host/ohci-spear.c new file mode 100644 index 000000000000..4fd4bea9ac7a --- /dev/null +++ b/drivers/usb/host/ohci-spear.c @@ -0,0 +1,240 @@ +/* +* OHCI HCD (Host Controller Driver) for USB. +* +* Copyright (C) 2010 ST Microelectronics. +* Deepak Sikri<deepak.sikri@st.com> +* +* Based on various ohci-*.c drivers +* +* This file is licensed under the terms of the GNU General Public +* License version 2. This program is licensed "as is" without any +* warranty of any kind, whether express or implied. +*/ + +#include <linux/signal.h> +#include <linux/platform_device.h> +#include <linux/clk.h> + +struct spear_ohci { + struct ohci_hcd ohci; + struct clk *clk; +}; + +#define to_spear_ohci(hcd) (struct spear_ohci *)hcd_to_ohci(hcd) + +static void spear_start_ohci(struct spear_ohci *ohci) +{ + clk_enable(ohci->clk); +} + +static void spear_stop_ohci(struct spear_ohci *ohci) +{ + clk_disable(ohci->clk); +} + +static int __devinit ohci_spear_start(struct usb_hcd *hcd) +{ + struct ohci_hcd *ohci = hcd_to_ohci(hcd); + int ret; + + ret = ohci_init(ohci); + if (ret < 0) + return ret; + ohci->regs = hcd->regs; + + ret = ohci_run(ohci); + if (ret < 0) { + dev_err(hcd->self.controller, "can't start\n"); + ohci_stop(hcd); + return ret; + } + + create_debug_files(ohci); + +#ifdef DEBUG + ohci_dump(ohci, 1); +#endif + return 0; +} + +static const struct hc_driver ohci_spear_hc_driver = { + .description = hcd_name, + .product_desc = "SPEAr OHCI", + .hcd_priv_size = sizeof(struct spear_ohci), + + /* generic hardware linkage */ + .irq = ohci_irq, + .flags = HCD_USB11 | HCD_MEMORY, + + /* basic lifecycle operations */ + .start = ohci_spear_start, + .stop = ohci_stop, + .shutdown = ohci_shutdown, +#ifdef CONFIG_PM + .bus_suspend = ohci_bus_suspend, + .bus_resume = ohci_bus_resume, +#endif + + /* managing i/o requests and associated device resources */ + .urb_enqueue = ohci_urb_enqueue, + .urb_dequeue = ohci_urb_dequeue, + .endpoint_disable = ohci_endpoint_disable, + + /* scheduling support */ + .get_frame_number = ohci_get_frame, + + /* root hub support */ + .hub_status_data = ohci_hub_status_data, + .hub_control = ohci_hub_control, + + .start_port_reset = ohci_start_port_reset, +}; + +static int spear_ohci_hcd_drv_probe(struct platform_device *pdev) +{ + const struct hc_driver *driver = &ohci_spear_hc_driver; + struct usb_hcd *hcd = NULL; + struct clk *usbh_clk; + struct spear_ohci *ohci_p; + struct resource *res; + int retval, irq; + int *pdata = pdev->dev.platform_data; + char clk_name[20] = "usbh_clk"; + + if (pdata == NULL) + return -EFAULT; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + retval = irq; + goto fail_irq_get; + } + + if (*pdata >= 0) + sprintf(clk_name, "usbh.%01d_clk", *pdata); + + usbh_clk = clk_get(NULL, clk_name); + if (IS_ERR(usbh_clk)) { + dev_err(&pdev->dev, "Error getting interface clock\n"); + retval = PTR_ERR(usbh_clk); + goto fail_get_usbh_clk; + } + + hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev)); + if (!hcd) { + retval = -ENOMEM; + goto fail_create_hcd; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + retval = -ENODEV; + goto fail_request_resource; + } + + hcd->rsrc_start = pdev->resource[0].start; + hcd->rsrc_len = resource_size(res); + if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) { + dev_dbg(&pdev->dev, "request_mem_region failed\n"); + retval = -EBUSY; + goto fail_request_resource; + } + + hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len); + if (!hcd->regs) { + dev_dbg(&pdev->dev, "ioremap failed\n"); + retval = -ENOMEM; + goto fail_ioremap; + } + + ohci_p = (struct spear_ohci *)hcd_to_ohci(hcd); + ohci_p->clk = usbh_clk; + spear_start_ohci(ohci_p); + ohci_hcd_init(hcd_to_ohci(hcd)); + + retval = usb_add_hcd(hcd, platform_get_irq(pdev, 0), IRQF_DISABLED); + if (retval == 0) + return retval; + + spear_stop_ohci(ohci_p); + iounmap(hcd->regs); +fail_ioremap: + release_mem_region(hcd->rsrc_start, hcd->rsrc_len); +fail_request_resource: + usb_put_hcd(hcd); +fail_create_hcd: + clk_put(usbh_clk); +fail_get_usbh_clk: +fail_irq_get: + dev_err(&pdev->dev, "init fail, %d\n", retval); + + return retval; +} + +static int spear_ohci_hcd_drv_remove(struct platform_device *pdev) +{ + struct usb_hcd *hcd = platform_get_drvdata(pdev); + struct spear_ohci *ohci_p = to_spear_ohci(hcd); + + usb_remove_hcd(hcd); + if (ohci_p->clk) + spear_stop_ohci(ohci_p); + + iounmap(hcd->regs); + release_mem_region(hcd->rsrc_start, hcd->rsrc_len); + usb_put_hcd(hcd); + + if (ohci_p->clk) + clk_put(ohci_p->clk); + platform_set_drvdata(pdev, NULL); + return 0; +} + +#if defined(CONFIG_PM) +static int spear_ohci_hcd_drv_suspend(struct platform_device *dev, + pm_message_t message) +{ + struct usb_hcd *hcd = platform_get_drvdata(dev); + struct ohci_hcd *ohci = hcd_to_ohci(hcd); + struct spear_ohci *ohci_p = to_spear_ohci(hcd); + + if (time_before(jiffies, ohci->next_statechange)) + msleep(5); + ohci->next_statechange = jiffies; + + spear_stop_ohci(ohci_p); + ohci_to_hcd(ohci)->state = HC_STATE_SUSPENDED; + return 0; +} + +static int spear_ohci_hcd_drv_resume(struct platform_device *dev) +{ + struct usb_hcd *hcd = platform_get_drvdata(dev); + struct ohci_hcd *ohci = hcd_to_ohci(hcd); + struct spear_ohci *ohci_p = to_spear_ohci(hcd); + + if (time_before(jiffies, ohci->next_statechange)) + msleep(5); + ohci->next_statechange = jiffies; + + spear_start_ohci(ohci_p); + ohci_finish_controller_resume(hcd); + return 0; +} +#endif + +/* Driver definition to register with the platform bus */ +static struct platform_driver spear_ohci_hcd_driver = { + .probe = spear_ohci_hcd_drv_probe, + .remove = spear_ohci_hcd_drv_remove, +#ifdef CONFIG_PM + .suspend = spear_ohci_hcd_drv_suspend, + .resume = spear_ohci_hcd_drv_resume, +#endif + .driver = { + .owner = THIS_MODULE, + .name = "spear-ohci", + }, +}; + +MODULE_ALIAS("platform:spear-ohci"); diff --git a/drivers/usb/host/uhci-hcd.c b/drivers/usb/host/uhci-hcd.c index f52d04db28f4..cee867829ec9 100644 --- a/drivers/usb/host/uhci-hcd.c +++ b/drivers/usb/host/uhci-hcd.c @@ -569,7 +569,7 @@ static int uhci_init(struct usb_hcd *hcd) */ static void uhci_shutdown(struct pci_dev *pdev) { - struct usb_hcd *hcd = (struct usb_hcd *) pci_get_drvdata(pdev); + struct usb_hcd *hcd = pci_get_drvdata(pdev); uhci_hc_died(hcd_to_uhci(hcd)); } diff --git a/drivers/usb/host/uhci-q.c b/drivers/usb/host/uhci-q.c index 2090b45eb606..af77abb5c68b 100644 --- a/drivers/usb/host/uhci-q.c +++ b/drivers/usb/host/uhci-q.c @@ -29,7 +29,7 @@ static void uhci_set_next_interrupt(struct uhci_hcd *uhci) { if (uhci->is_stopped) mod_timer(&uhci_to_hcd(uhci)->rh_timer, jiffies); - uhci->term_td->status |= cpu_to_le32(TD_CTRL_IOC); + uhci->term_td->status |= cpu_to_le32(TD_CTRL_IOC); } static inline void uhci_clear_next_interrupt(struct uhci_hcd *uhci) @@ -195,7 +195,9 @@ static inline void uhci_remove_td_from_frame_list(struct uhci_hcd *uhci, } else { struct uhci_td *ntd; - ntd = list_entry(td->fl_list.next, struct uhci_td, fl_list); + ntd = list_entry(td->fl_list.next, + struct uhci_td, + fl_list); uhci->frame[td->frame] = LINK_TO_TD(ntd); uhci->frame_cpu[td->frame] = ntd; } @@ -728,7 +730,7 @@ static inline struct urb_priv *uhci_alloc_urb_priv(struct uhci_hcd *uhci, urbp->urb = urb; urb->hcpriv = urbp; - + INIT_LIST_HEAD(&urbp->node); INIT_LIST_HEAD(&urbp->td_list); @@ -846,7 +848,7 @@ static int uhci_submit_control(struct uhci_hcd *uhci, struct urb *urb, /* Alternate Data0/1 (start with Data1) */ destination ^= TD_TOKEN_TOGGLE; - + uhci_add_td_to_urbp(td, urbp); uhci_fill_td(td, status, destination | uhci_explen(pktsze), data); @@ -857,7 +859,7 @@ static int uhci_submit_control(struct uhci_hcd *uhci, struct urb *urb, } /* - * Build the final TD for control status + * Build the final TD for control status */ td = uhci_alloc_td(uhci); if (!td) diff --git a/drivers/usb/host/whci/hcd.c b/drivers/usb/host/whci/hcd.c index 72b6892fda67..9546f6cd01f0 100644 --- a/drivers/usb/host/whci/hcd.c +++ b/drivers/usb/host/whci/hcd.c @@ -356,7 +356,7 @@ static void __exit whci_hc_driver_exit(void) module_exit(whci_hc_driver_exit); /* PCI device ID's that we handle (so it gets loaded) */ -static struct pci_device_id whci_hcd_id_table[] = { +static struct pci_device_id __used whci_hcd_id_table[] = { { PCI_DEVICE_CLASS(PCI_CLASS_WIRELESS_WHCI, ~0) }, { /* empty last entry */ } }; diff --git a/drivers/usb/mon/mon_bin.c b/drivers/usb/mon/mon_bin.c index c436e1e2c3b6..a09dbd243eb3 100644 --- a/drivers/usb/mon/mon_bin.c +++ b/drivers/usb/mon/mon_bin.c @@ -436,6 +436,28 @@ static unsigned int mon_bin_get_data(const struct mon_reader_bin *rp, return length; } +/* + * This is the look-ahead pass in case of 'C Zi', when actual_length cannot + * be used to determine the length of the whole contiguous buffer. + */ +static unsigned int mon_bin_collate_isodesc(const struct mon_reader_bin *rp, + struct urb *urb, unsigned int ndesc) +{ + struct usb_iso_packet_descriptor *fp; + unsigned int length; + + length = 0; + fp = urb->iso_frame_desc; + while (ndesc-- != 0) { + if (fp->actual_length != 0) { + if (fp->offset + fp->actual_length > length) + length = fp->offset + fp->actual_length; + } + fp++; + } + return length; +} + static void mon_bin_get_isodesc(const struct mon_reader_bin *rp, unsigned int offset, struct urb *urb, char ev_type, unsigned int ndesc) { @@ -478,6 +500,10 @@ static void mon_bin_event(struct mon_reader_bin *rp, struct urb *urb, /* * Find the maximum allowable length, then allocate space. */ + urb_length = (ev_type == 'S') ? + urb->transfer_buffer_length : urb->actual_length; + length = urb_length; + if (usb_endpoint_xfer_isoc(epd)) { if (urb->number_of_packets < 0) { ndesc = 0; @@ -486,14 +512,16 @@ static void mon_bin_event(struct mon_reader_bin *rp, struct urb *urb, } else { ndesc = urb->number_of_packets; } + if (ev_type == 'C' && usb_urb_dir_in(urb)) + length = mon_bin_collate_isodesc(rp, urb, ndesc); } else { ndesc = 0; } lendesc = ndesc*sizeof(struct mon_bin_isodesc); - urb_length = (ev_type == 'S') ? - urb->transfer_buffer_length : urb->actual_length; - length = urb_length; + /* not an issue unless there's a subtle bug in a HCD somewhere */ + if (length >= urb->transfer_buffer_length) + length = urb->transfer_buffer_length; if (length >= rp->b_size/5) length = rp->b_size/5; diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig index 341a37a469bd..4cbb7e4b368d 100644 --- a/drivers/usb/musb/Kconfig +++ b/drivers/usb/musb/Kconfig @@ -12,6 +12,7 @@ config USB_MUSB_HDRC depends on (ARM || (BF54x && !BF544) || (BF52x && !BF522 && !BF523)) select NOP_USB_XCEIV if (ARCH_DAVINCI || MACH_OMAP3EVM || BLACKFIN) select TWL4030_USB if MACH_OMAP_3430SDP + select TWL6030_USB if MACH_OMAP_4430SDP || MACH_OMAP4_PANDA select USB_OTG_UTILS tristate 'Inventra Highspeed Dual Role Controller (TI, ADI, ...)' help @@ -30,57 +31,41 @@ config USB_MUSB_HDRC If you do not know what this is, please say N. To compile this driver as a module, choose M here; the - module will be called "musb_hdrc". + module will be called "musb-hdrc". -config USB_MUSB_SOC - boolean +choice + prompt "Platform Glue Layer" depends on USB_MUSB_HDRC - default y if ARCH_DAVINCI - default y if ARCH_OMAP2430 - default y if ARCH_OMAP3 - default y if ARCH_OMAP4 - default y if (BF54x && !BF544) - default y if (BF52x && !BF522 && !BF523) -comment "DaVinci 35x and 644x USB support" - depends on USB_MUSB_HDRC && ARCH_DAVINCI_DMx +config USB_MUSB_DAVINCI + bool "DaVinci" + depends on ARCH_DAVINCI_DMx -comment "DA8xx/OMAP-L1x USB support" - depends on USB_MUSB_HDRC && ARCH_DAVINCI_DA8XX +config USB_MUSB_DA8XX + bool "DA8xx/OMAP-L1x" + depends on ARCH_DAVINCI_DA8XX -comment "OMAP 243x high speed USB support" - depends on USB_MUSB_HDRC && ARCH_OMAP2430 +config USB_MUSB_TUSB6010 + bool "TUSB6010" + depends on ARCH_OMAP -comment "OMAP 343x high speed USB support" - depends on USB_MUSB_HDRC && ARCH_OMAP3 +config USB_MUSB_OMAP2PLUS + bool "OMAP2430 and onwards" + depends on ARCH_OMAP2PLUS -comment "OMAP 44xx high speed USB support" - depends on USB_MUSB_HDRC && ARCH_OMAP4 +config USB_MUSB_AM35X + bool "AM35x" + depends on ARCH_OMAP -comment "Blackfin high speed USB Support" - depends on USB_MUSB_HDRC && ((BF54x && !BF544) || (BF52x && !BF522 && !BF523)) +config USB_MUSB_BLACKFIN + bool "Blackfin" + depends on (BF54x && !BF544) || (BF52x && ! BF522 && !BF523) -config USB_MUSB_AM35X - bool - depends on USB_MUSB_HDRC && !ARCH_OMAP2430 && !ARCH_OMAP4 - select NOP_USB_XCEIV - default MACH_OMAP3517EVM - help - Select this option if your platform is based on AM35x. As - AM35x has an updated MUSB with CPPI4.1 DMA so this config - is introduced to differentiate musb ip between OMAP3x and - AM35x platforms. - -config USB_TUSB6010 - boolean "TUSB 6010 support" - depends on USB_MUSB_HDRC && !USB_MUSB_SOC - select NOP_USB_XCEIV - default y - help - The TUSB 6010 chip, from Texas Instruments, connects a discrete - HDRC core using a 16-bit parallel bus (NOR flash style) or VLYNQ - (a high speed serial link). It can use system-specific external - DMA controllers. +config USB_MUSB_UX500 + bool "U8500 and U5500" + depends on (ARCH_U8500 && AB8500_USB) || (ARCH_U5500) + +endchoice choice prompt "Driver Mode" @@ -158,7 +143,7 @@ config USB_MUSB_HDRC_HCD config MUSB_PIO_ONLY bool 'Disable DMA (always use PIO)' depends on USB_MUSB_HDRC - default USB_TUSB6010 || ARCH_DAVINCI_DA8XX || USB_MUSB_AM35X + default USB_MUSB_TUSB6010 || USB_MUSB_DA8XX || USB_MUSB_AM35X help All data is copied between memory and FIFO by the CPU. DMA controllers are ignored. @@ -171,21 +156,21 @@ config MUSB_PIO_ONLY config USB_INVENTRA_DMA bool depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY - default ARCH_OMAP2430 || ARCH_OMAP3 || BLACKFIN || ARCH_OMAP4 + default USB_MUSB_OMAP2PLUS || USB_MUSB_BLACKFIN help Enable DMA transfers using Mentor's engine. config USB_TI_CPPI_DMA bool depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY - default ARCH_DAVINCI + default USB_MUSB_DAVINCI help Enable DMA transfers when TI CPPI DMA is available. config USB_TUSB_OMAP_DMA bool depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY - depends on USB_TUSB6010 + depends on USB_MUSB_TUSB6010 depends on ARCH_OMAP default y help diff --git a/drivers/usb/musb/Makefile b/drivers/usb/musb/Makefile index ce164e8998d8..74df5284894f 100644 --- a/drivers/usb/musb/Makefile +++ b/drivers/usb/musb/Makefile @@ -8,22 +8,19 @@ obj-$(CONFIG_USB_MUSB_HDRC) += musb_hdrc.o musb_hdrc-y := musb_core.o -musb_hdrc-$(CONFIG_ARCH_DAVINCI_DMx) += davinci.o -musb_hdrc-$(CONFIG_ARCH_DAVINCI_DA8XX) += da8xx.o -musb_hdrc-$(CONFIG_USB_TUSB6010) += tusb6010.o -musb_hdrc-$(CONFIG_ARCH_OMAP2430) += omap2430.o -ifeq ($(CONFIG_USB_MUSB_AM35X),y) - musb_hdrc-$(CONFIG_ARCH_OMAP3430) += am35x.o -else - musb_hdrc-$(CONFIG_ARCH_OMAP3430) += omap2430.o -endif -musb_hdrc-$(CONFIG_ARCH_OMAP4) += omap2430.o -musb_hdrc-$(CONFIG_BF54x) += blackfin.o -musb_hdrc-$(CONFIG_BF52x) += blackfin.o musb_hdrc-$(CONFIG_USB_GADGET_MUSB_HDRC) += musb_gadget_ep0.o musb_gadget.o musb_hdrc-$(CONFIG_USB_MUSB_HDRC_HCD) += musb_virthub.o musb_host.o musb_hdrc-$(CONFIG_DEBUG_FS) += musb_debugfs.o +# Hardware Glue Layer +obj-$(CONFIG_USB_MUSB_OMAP2PLUS) += omap2430.o +obj-$(CONFIG_USB_MUSB_AM35X) += am35x.o +obj-$(CONFIG_USB_MUSB_TUSB6010) += tusb6010.o +obj-$(CONFIG_USB_MUSB_DAVINCI) += davinci.o +obj-$(CONFIG_USB_MUSB_DA8XX) += da8xx.o +obj-$(CONFIG_USB_MUSB_BLACKFIN) += blackfin.o +obj-$(CONFIG_USB_MUSB_UX500) += ux500.o + # the kconfig must guarantee that only one of the # possible I/O schemes will be enabled at a time ... # PIO only, or DMA (several potential schemes). diff --git a/drivers/usb/musb/am35x.c b/drivers/usb/musb/am35x.c index b0aabf3a606f..d5a3da37c90c 100644 --- a/drivers/usb/musb/am35x.c +++ b/drivers/usb/musb/am35x.c @@ -29,8 +29,9 @@ #include <linux/init.h> #include <linux/clk.h> #include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/dma-mapping.h> -#include <plat/control.h> #include <plat/usb.h> #include "musb_core.h" @@ -80,51 +81,18 @@ #define USB_MENTOR_CORE_OFFSET 0x400 -static inline void phy_on(void) -{ - unsigned long timeout = jiffies + msecs_to_jiffies(100); - u32 devconf2; - - /* - * Start the on-chip PHY and its PLL. - */ - devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2); - - devconf2 &= ~(CONF2_RESET | CONF2_PHYPWRDN | CONF2_OTGPWRDN); - devconf2 |= CONF2_PHY_PLLON; - - omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2); - - DBG(1, "Waiting for PHY clock good...\n"); - while (!(omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2) - & CONF2_PHYCLKGD)) { - cpu_relax(); - - if (time_after(jiffies, timeout)) { - DBG(1, "musb PHY clock good timed out\n"); - break; - } - } -} - -static inline void phy_off(void) -{ - u32 devconf2; - - /* - * Power down the on-chip PHY. - */ - devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2); - - devconf2 &= ~CONF2_PHY_PLLON; - devconf2 |= CONF2_PHYPWRDN | CONF2_OTGPWRDN; - omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2); -} +struct am35x_glue { + struct device *dev; + struct platform_device *musb; + struct clk *phy_clk; + struct clk *clk; +}; +#define glue_to_musb(g) platform_get_drvdata(g->musb) /* - * musb_platform_enable - enable interrupts + * am35x_musb_enable - enable interrupts */ -void musb_platform_enable(struct musb *musb) +static void am35x_musb_enable(struct musb *musb) { void __iomem *reg_base = musb->ctrl_base; u32 epmask; @@ -143,9 +111,9 @@ void musb_platform_enable(struct musb *musb) } /* - * musb_platform_disable - disable HDRC and flush interrupts + * am35x_musb_disable - disable HDRC and flush interrupts */ -void musb_platform_disable(struct musb *musb) +static void am35x_musb_disable(struct musb *musb) { void __iomem *reg_base = musb->ctrl_base; @@ -162,7 +130,7 @@ void musb_platform_disable(struct musb *musb) #define portstate(stmt) #endif -static void am35x_set_vbus(struct musb *musb, int is_on) +static void am35x_musb_set_vbus(struct musb *musb, int is_on) { WARN_ON(is_on && is_peripheral_active(musb)); } @@ -221,7 +189,7 @@ static void otg_timer(unsigned long _musb) spin_unlock_irqrestore(&musb->lock, flags); } -void musb_platform_try_idle(struct musb *musb, unsigned long timeout) +static void am35x_musb_try_idle(struct musb *musb, unsigned long timeout) { static unsigned long last_timer; @@ -251,13 +219,16 @@ void musb_platform_try_idle(struct musb *musb, unsigned long timeout) mod_timer(&otg_workaround, timeout); } -static irqreturn_t am35x_interrupt(int irq, void *hci) +static irqreturn_t am35x_musb_interrupt(int irq, void *hci) { struct musb *musb = hci; void __iomem *reg_base = musb->ctrl_base; + struct device *dev = musb->controller; + struct musb_hdrc_platform_data *plat = dev->platform_data; + struct omap_musb_board_data *data = plat->board_data; unsigned long flags; irqreturn_t ret = IRQ_NONE; - u32 epintr, usbintr, lvl_intr; + u32 epintr, usbintr; spin_lock_irqsave(&musb->lock, flags); @@ -346,9 +317,8 @@ eoi: /* EOI needs to be written for the IRQ to be re-asserted. */ if (ret == IRQ_HANDLED || epintr || usbintr) { /* clear level interrupt */ - lvl_intr = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR); - lvl_intr |= AM35XX_USBOTGSS_INT_CLR; - omap_ctrl_writel(lvl_intr, AM35XX_CONTROL_LVL_INTR_CLEAR); + if (data->clear_irq) + data->clear_irq(); /* write EOI */ musb_writel(reg_base, USB_END_OF_INTR_REG, 0); } @@ -362,137 +332,85 @@ eoi: return ret; } -int musb_platform_set_mode(struct musb *musb, u8 musb_mode) +static int am35x_musb_set_mode(struct musb *musb, u8 musb_mode) { - u32 devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2); + struct device *dev = musb->controller; + struct musb_hdrc_platform_data *plat = dev->platform_data; + struct omap_musb_board_data *data = plat->board_data; + int retval = 0; - devconf2 &= ~CONF2_OTGMODE; - switch (musb_mode) { -#ifdef CONFIG_USB_MUSB_HDRC_HCD - case MUSB_HOST: /* Force VBUS valid, ID = 0 */ - devconf2 |= CONF2_FORCE_HOST; - break; -#endif -#ifdef CONFIG_USB_GADGET_MUSB_HDRC - case MUSB_PERIPHERAL: /* Force VBUS valid, ID = 1 */ - devconf2 |= CONF2_FORCE_DEVICE; - break; -#endif -#ifdef CONFIG_USB_MUSB_OTG - case MUSB_OTG: /* Don't override the VBUS/ID comparators */ - devconf2 |= CONF2_NO_OVERRIDE; - break; -#endif - default: - DBG(2, "Trying to set unsupported mode %u\n", musb_mode); - } + if (data->set_mode) + data->set_mode(musb_mode); + else + retval = -EIO; - omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2); - return 0; + return retval; } -int __init musb_platform_init(struct musb *musb, void *board_data) +static int am35x_musb_init(struct musb *musb) { + struct device *dev = musb->controller; + struct musb_hdrc_platform_data *plat = dev->platform_data; + struct omap_musb_board_data *data = plat->board_data; void __iomem *reg_base = musb->ctrl_base; - u32 rev, lvl_intr, sw_reset; - int status; + u32 rev; musb->mregs += USB_MENTOR_CORE_OFFSET; - clk_enable(musb->clock); - DBG(2, "musb->clock=%lud\n", clk_get_rate(musb->clock)); - - musb->phy_clock = clk_get(musb->controller, "fck"); - if (IS_ERR(musb->phy_clock)) { - status = PTR_ERR(musb->phy_clock); - goto exit0; - } - clk_enable(musb->phy_clock); - DBG(2, "musb->phy_clock=%lud\n", clk_get_rate(musb->phy_clock)); - /* Returns zero if e.g. not clocked */ rev = musb_readl(reg_base, USB_REVISION_REG); - if (!rev) { - status = -ENODEV; - goto exit1; - } + if (!rev) + return -ENODEV; usb_nop_xceiv_register(); musb->xceiv = otg_get_transceiver(); - if (!musb->xceiv) { - status = -ENODEV; - goto exit1; - } + if (!musb->xceiv) + return -ENODEV; if (is_host_enabled(musb)) setup_timer(&otg_workaround, otg_timer, (unsigned long) musb); - musb->board_set_vbus = am35x_set_vbus; - - /* Global reset */ - sw_reset = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET); - - sw_reset |= AM35XX_USBOTGSS_SW_RST; - omap_ctrl_writel(sw_reset, AM35XX_CONTROL_IP_SW_RESET); - - sw_reset &= ~AM35XX_USBOTGSS_SW_RST; - omap_ctrl_writel(sw_reset, AM35XX_CONTROL_IP_SW_RESET); + /* Reset the musb */ + if (data->reset) + data->reset(); /* Reset the controller */ musb_writel(reg_base, USB_CTRL_REG, AM35X_SOFT_RESET_MASK); /* Start the on-chip PHY and its PLL. */ - phy_on(); + if (data->set_phy_power) + data->set_phy_power(1); msleep(5); - musb->isr = am35x_interrupt; + musb->isr = am35x_musb_interrupt; /* clear level interrupt */ - lvl_intr = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR); - lvl_intr |= AM35XX_USBOTGSS_INT_CLR; - omap_ctrl_writel(lvl_intr, AM35XX_CONTROL_LVL_INTR_CLEAR); + if (data->clear_irq) + data->clear_irq(); + return 0; -exit1: - clk_disable(musb->phy_clock); - clk_put(musb->phy_clock); -exit0: - clk_disable(musb->clock); - return status; } -int musb_platform_exit(struct musb *musb) +static int am35x_musb_exit(struct musb *musb) { + struct device *dev = musb->controller; + struct musb_hdrc_platform_data *plat = dev->platform_data; + struct omap_musb_board_data *data = plat->board_data; + if (is_host_enabled(musb)) del_timer_sync(&otg_workaround); - phy_off(); + /* Shutdown the on-chip PHY and its PLL. */ + if (data->set_phy_power) + data->set_phy_power(0); otg_put_transceiver(musb->xceiv); usb_nop_xceiv_unregister(); - clk_disable(musb->clock); - - clk_disable(musb->phy_clock); - clk_put(musb->phy_clock); - return 0; } -#ifdef CONFIG_PM -void musb_platform_save_context(struct musb *musb, - struct musb_context_registers *musb_context) -{ - phy_off(); -} - -void musb_platform_restore_context(struct musb *musb, - struct musb_context_registers *musb_context) -{ - phy_on(); -} -#endif - /* AM35x supports only 32bit read operation */ void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst) { @@ -522,3 +440,215 @@ void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst) memcpy(dst, &val, len); } } + +static const struct musb_platform_ops am35x_ops = { + .init = am35x_musb_init, + .exit = am35x_musb_exit, + + .enable = am35x_musb_enable, + .disable = am35x_musb_disable, + + .set_mode = am35x_musb_set_mode, + .try_idle = am35x_musb_try_idle, + + .set_vbus = am35x_musb_set_vbus, +}; + +static u64 am35x_dmamask = DMA_BIT_MASK(32); + +static int __init am35x_probe(struct platform_device *pdev) +{ + struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data; + struct platform_device *musb; + struct am35x_glue *glue; + + struct clk *phy_clk; + struct clk *clk; + + int ret = -ENOMEM; + + glue = kzalloc(sizeof(*glue), GFP_KERNEL); + if (!glue) { + dev_err(&pdev->dev, "failed to allocate glue context\n"); + goto err0; + } + + musb = platform_device_alloc("musb-hdrc", -1); + if (!musb) { + dev_err(&pdev->dev, "failed to allocate musb device\n"); + goto err1; + } + + phy_clk = clk_get(&pdev->dev, "fck"); + if (IS_ERR(phy_clk)) { + dev_err(&pdev->dev, "failed to get PHY clock\n"); + ret = PTR_ERR(phy_clk); + goto err2; + } + + clk = clk_get(&pdev->dev, "ick"); + if (IS_ERR(clk)) { + dev_err(&pdev->dev, "failed to get clock\n"); + ret = PTR_ERR(clk); + goto err3; + } + + ret = clk_enable(phy_clk); + if (ret) { + dev_err(&pdev->dev, "failed to enable PHY clock\n"); + goto err4; + } + + ret = clk_enable(clk); + if (ret) { + dev_err(&pdev->dev, "failed to enable clock\n"); + goto err5; + } + + musb->dev.parent = &pdev->dev; + musb->dev.dma_mask = &am35x_dmamask; + musb->dev.coherent_dma_mask = am35x_dmamask; + + glue->dev = &pdev->dev; + glue->musb = musb; + glue->phy_clk = phy_clk; + glue->clk = clk; + + pdata->platform_ops = &am35x_ops; + + platform_set_drvdata(pdev, glue); + + ret = platform_device_add_resources(musb, pdev->resource, + pdev->num_resources); + if (ret) { + dev_err(&pdev->dev, "failed to add resources\n"); + goto err6; + } + + ret = platform_device_add_data(musb, pdata, sizeof(*pdata)); + if (ret) { + dev_err(&pdev->dev, "failed to add platform_data\n"); + goto err6; + } + + ret = platform_device_add(musb); + if (ret) { + dev_err(&pdev->dev, "failed to register musb device\n"); + goto err6; + } + + return 0; + +err6: + clk_disable(clk); + +err5: + clk_disable(phy_clk); + +err4: + clk_put(clk); + +err3: + clk_put(phy_clk); + +err2: + platform_device_put(musb); + +err1: + kfree(glue); + +err0: + return ret; +} + +static int __exit am35x_remove(struct platform_device *pdev) +{ + struct am35x_glue *glue = platform_get_drvdata(pdev); + + platform_device_del(glue->musb); + platform_device_put(glue->musb); + clk_disable(glue->clk); + clk_disable(glue->phy_clk); + clk_put(glue->clk); + clk_put(glue->phy_clk); + kfree(glue); + + return 0; +} + +#ifdef CONFIG_PM +static int am35x_suspend(struct device *dev) +{ + struct am35x_glue *glue = dev_get_drvdata(dev); + struct musb_hdrc_platform_data *plat = dev->platform_data; + struct omap_musb_board_data *data = plat->board_data; + + /* Shutdown the on-chip PHY and its PLL. */ + if (data->set_phy_power) + data->set_phy_power(0); + + clk_disable(glue->phy_clk); + clk_disable(glue->clk); + + return 0; +} + +static int am35x_resume(struct device *dev) +{ + struct am35x_glue *glue = dev_get_drvdata(dev); + struct musb_hdrc_platform_data *plat = dev->platform_data; + struct omap_musb_board_data *data = plat->board_data; + int ret; + + /* Start the on-chip PHY and its PLL. */ + if (data->set_phy_power) + data->set_phy_power(1); + + ret = clk_enable(glue->phy_clk); + if (ret) { + dev_err(dev, "failed to enable PHY clock\n"); + return ret; + } + + ret = clk_enable(glue->clk); + if (ret) { + dev_err(dev, "failed to enable clock\n"); + return ret; + } + + return 0; +} + +static struct dev_pm_ops am35x_pm_ops = { + .suspend = am35x_suspend, + .resume = am35x_resume, +}; + +#define DEV_PM_OPS &am35x_pm_ops +#else +#define DEV_PM_OPS NULL +#endif + +static struct platform_driver am35x_driver = { + .remove = __exit_p(am35x_remove), + .driver = { + .name = "musb-am35x", + .pm = DEV_PM_OPS, + }, +}; + +MODULE_DESCRIPTION("AM35x MUSB Glue Layer"); +MODULE_AUTHOR("Ajay Kumar Gupta <ajay.gupta@ti.com>"); +MODULE_LICENSE("GPL v2"); + +static int __init am35x_init(void) +{ + return platform_driver_probe(&am35x_driver, am35x_probe); +} +subsys_initcall(am35x_init); + +static void __exit am35x_exit(void) +{ + platform_driver_unregister(&am35x_driver); +} +module_exit(am35x_exit); diff --git a/drivers/usb/musb/blackfin.c b/drivers/usb/musb/blackfin.c index 930a2611fe3e..eeba228eb2af 100644 --- a/drivers/usb/musb/blackfin.c +++ b/drivers/usb/musb/blackfin.c @@ -15,12 +15,20 @@ #include <linux/list.h> #include <linux/gpio.h> #include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/dma-mapping.h> #include <asm/cacheflush.h> #include "musb_core.h" #include "blackfin.h" +struct bfin_glue { + struct device *dev; + struct platform_device *musb; +}; +#define glue_to_musb(g) platform_get_drvdata(g->musb) + /* * Load an endpoint's FIFO */ @@ -278,7 +286,7 @@ static void musb_conn_timer_handler(unsigned long _musb) DBG(4, "state is %s\n", otg_state_string(musb)); } -void musb_platform_enable(struct musb *musb) +static void bfin_musb_enable(struct musb *musb) { if (!is_otg_enabled(musb) && is_host_enabled(musb)) { mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY); @@ -286,11 +294,11 @@ void musb_platform_enable(struct musb *musb) } } -void musb_platform_disable(struct musb *musb) +static void bfin_musb_disable(struct musb *musb) { } -static void bfin_set_vbus(struct musb *musb, int is_on) +static void bfin_musb_set_vbus(struct musb *musb, int is_on) { int value = musb->config->gpio_vrsel_active; if (!is_on) @@ -303,51 +311,29 @@ static void bfin_set_vbus(struct musb *musb, int is_on) musb_readb(musb->mregs, MUSB_DEVCTL)); } -static int bfin_set_power(struct otg_transceiver *x, unsigned mA) +static int bfin_musb_set_power(struct otg_transceiver *x, unsigned mA) { return 0; } -void musb_platform_try_idle(struct musb *musb, unsigned long timeout) +static void bfin_musb_try_idle(struct musb *musb, unsigned long timeout) { if (!is_otg_enabled(musb) && is_host_enabled(musb)) mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY); } -int musb_platform_get_vbus_status(struct musb *musb) +static int bfin_musb_get_vbus_status(struct musb *musb) { return 0; } -int musb_platform_set_mode(struct musb *musb, u8 musb_mode) +static int bfin_musb_set_mode(struct musb *musb, u8 musb_mode) { return -EIO; } -int __init musb_platform_init(struct musb *musb, void *board_data) +static void bfin_musb_reg_init(struct musb *musb) { - - /* - * Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE - * and OTG HOST modes, while rev 1.1 and greater require PE7 to - * be low for DEVICE mode and high for HOST mode. We set it high - * here because we are in host mode - */ - - if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) { - printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d \n", - musb->config->gpio_vrsel); - return -ENODEV; - } - gpio_direction_output(musb->config->gpio_vrsel, 0); - - usb_nop_xceiv_register(); - musb->xceiv = otg_get_transceiver(); - if (!musb->xceiv) { - gpio_free(musb->config->gpio_vrsel); - return -ENODEV; - } - if (ANOMALY_05000346) { bfin_write_USB_APHY_CALIB(ANOMALY_05000346_value); SSYNC(); @@ -382,21 +368,47 @@ int __init musb_platform_init(struct musb *musb, void *board_data) EP2_RX_ENA | EP3_RX_ENA | EP4_RX_ENA | EP5_RX_ENA | EP6_RX_ENA | EP7_RX_ENA); SSYNC(); +} + +static int bfin_musb_init(struct musb *musb) +{ + + /* + * Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE + * and OTG HOST modes, while rev 1.1 and greater require PE7 to + * be low for DEVICE mode and high for HOST mode. We set it high + * here because we are in host mode + */ + + if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) { + printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d\n", + musb->config->gpio_vrsel); + return -ENODEV; + } + gpio_direction_output(musb->config->gpio_vrsel, 0); + + usb_nop_xceiv_register(); + musb->xceiv = otg_get_transceiver(); + if (!musb->xceiv) { + gpio_free(musb->config->gpio_vrsel); + return -ENODEV; + } + + bfin_musb_reg_init(musb); if (is_host_enabled(musb)) { - musb->board_set_vbus = bfin_set_vbus; setup_timer(&musb_conn_timer, musb_conn_timer_handler, (unsigned long) musb); } if (is_peripheral_enabled(musb)) - musb->xceiv->set_power = bfin_set_power; + musb->xceiv->set_power = bfin_musb_set_power; musb->isr = blackfin_interrupt; return 0; } -int musb_platform_exit(struct musb *musb) +static int bfin_musb_exit(struct musb *musb) { gpio_free(musb->config->gpio_vrsel); @@ -404,3 +416,154 @@ int musb_platform_exit(struct musb *musb) usb_nop_xceiv_unregister(); return 0; } + +static const struct musb_platform_ops bfin_ops = { + .init = bfin_musb_init, + .exit = bfin_musb_exit, + + .enable = bfin_musb_enable, + .disable = bfin_musb_disable, + + .set_mode = bfin_musb_set_mode, + .try_idle = bfin_musb_try_idle, + + .vbus_status = bfin_musb_vbus_status, + .set_vbus = bfin_musb_set_vbus, +}; + +static u64 bfin_dmamask = DMA_BIT_MASK(32); + +static int __init bfin_probe(struct platform_device *pdev) +{ + struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data; + struct platform_device *musb; + struct bfin_glue *glue; + + int ret = -ENOMEM; + + glue = kzalloc(sizeof(*glue), GFP_KERNEL); + if (!glue) { + dev_err(&pdev->dev, "failed to allocate glue context\n"); + goto err0; + } + + musb = platform_device_alloc("musb-hdrc", -1); + if (!musb) { + dev_err(&pdev->dev, "failed to allocate musb device\n"); + goto err1; + } + + musb->dev.parent = &pdev->dev; + musb->dev.dma_mask = &bfin_dmamask; + musb->dev.coherent_dma_mask = bfin_dmamask; + + glue->dev = &pdev->dev; + glue->musb = musb; + + pdata->platform_ops = &bfin_ops; + + platform_set_drvdata(pdev, glue); + + ret = platform_device_add_resources(musb, pdev->resource, + pdev->num_resources); + if (ret) { + dev_err(&pdev->dev, "failed to add resources\n"); + goto err2; + } + + ret = platform_device_add_data(musb, pdata, sizeof(*pdata)); + if (ret) { + dev_err(&pdev->dev, "failed to add platform_data\n"); + goto err2; + } + + ret = platform_device_add(musb); + if (ret) { + dev_err(&pdev->dev, "failed to register musb device\n"); + goto err2; + } + + return 0; + +err2: + platform_device_put(musb); + +err1: + kfree(glue); + +err0: + return ret; +} + +static int __exit bfin_remove(struct platform_device *pdev) +{ + struct bfin_glue *glue = platform_get_drvdata(pdev); + + platform_device_del(glue->musb); + platform_device_put(glue->musb); + kfree(glue); + + return 0; +} + +#ifdef CONFIG_PM +static int bfin_suspend(struct device *dev) +{ + struct bfin_glue *glue = dev_get_drvdata(dev); + struct musb *musb = glue_to_musb(glue); + + if (is_host_active(musb)) + /* + * During hibernate gpio_vrsel will change from high to low + * low which will generate wakeup event resume the system + * immediately. Set it to 0 before hibernate to avoid this + * wakeup event. + */ + gpio_set_value(musb->config->gpio_vrsel, 0); + + return 0; +} + +static int bfin_resume(struct device *dev) +{ + struct bfin_glue *glue = dev_get_drvdata(dev); + struct musb *musb = glue_to_musb(glue); + + bfin_musb_reg_init(musb); + + return 0; +} + +static struct dev_pm_ops bfin_pm_ops = { + .suspend = bfin_suspend, + .resume = bfin_resume, +}; + +#define DEV_PM_OPS &bfin_pm_op, +#else +#define DEV_PM_OPS NULL +#endif + +static struct platform_driver bfin_driver = { + .remove = __exit_p(bfin_remove), + .driver = { + .name = "musb-bfin", + .pm = DEV_PM_OPS, + }, +}; + +MODULE_DESCRIPTION("Blackfin MUSB Glue Layer"); +MODULE_AUTHOR("Bryan Wy <cooloney@kernel.org>"); +MODULE_LICENSE("GPL v2"); + +static int __init bfin_init(void) +{ + return platform_driver_probe(&bfin_driver, bfin_probe); +} +subsys_initcall(bfin_init); + +static void __exit bfin_exit(void) +{ + platform_driver_unregister(&bfin_driver); +} +module_exit(bfin_exit); diff --git a/drivers/usb/musb/cppi_dma.c b/drivers/usb/musb/cppi_dma.c index f5a65ff0ac2b..de55a3c3259a 100644 --- a/drivers/usb/musb/cppi_dma.c +++ b/drivers/usb/musb/cppi_dma.c @@ -1308,7 +1308,7 @@ dma_controller_create(struct musb *musb, void __iomem *mregs) struct cppi *controller; struct device *dev = musb->controller; struct platform_device *pdev = to_platform_device(dev); - int irq = platform_get_irq(pdev, 1); + int irq = platform_get_irq_byname(pdev, "dma"); controller = kzalloc(sizeof *controller, GFP_KERNEL); if (!controller) diff --git a/drivers/usb/musb/da8xx.c b/drivers/usb/musb/da8xx.c index 84427bebbf62..69a0da3c8f09 100644 --- a/drivers/usb/musb/da8xx.c +++ b/drivers/usb/musb/da8xx.c @@ -29,6 +29,8 @@ #include <linux/init.h> #include <linux/clk.h> #include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/dma-mapping.h> #include <mach/da8xx.h> #include <mach/usb.h> @@ -78,6 +80,12 @@ #define CFGCHIP2 IO_ADDRESS(DA8XX_SYSCFG0_BASE + DA8XX_CFGCHIP2_REG) +struct da8xx_glue { + struct device *dev; + struct platform_device *musb; + struct clk *clk; +}; + /* * REVISIT (PM): we should be able to keep the PHY in low power mode most * of the time (24 MHz oscillator and PLL off, etc.) by setting POWER.D0 @@ -131,9 +139,9 @@ static inline void phy_off(void) */ /** - * musb_platform_enable - enable interrupts + * da8xx_musb_enable - enable interrupts */ -void musb_platform_enable(struct musb *musb) +static void da8xx_musb_enable(struct musb *musb) { void __iomem *reg_base = musb->ctrl_base; u32 mask; @@ -151,9 +159,9 @@ void musb_platform_enable(struct musb *musb) } /** - * musb_platform_disable - disable HDRC and flush interrupts + * da8xx_musb_disable - disable HDRC and flush interrupts */ -void musb_platform_disable(struct musb *musb) +static void da8xx_musb_disable(struct musb *musb) { void __iomem *reg_base = musb->ctrl_base; @@ -170,7 +178,7 @@ void musb_platform_disable(struct musb *musb) #define portstate(stmt) #endif -static void da8xx_set_vbus(struct musb *musb, int is_on) +static void da8xx_musb_set_vbus(struct musb *musb, int is_on) { WARN_ON(is_on && is_peripheral_active(musb)); } @@ -252,7 +260,7 @@ static void otg_timer(unsigned long _musb) spin_unlock_irqrestore(&musb->lock, flags); } -void musb_platform_try_idle(struct musb *musb, unsigned long timeout) +static void da8xx_musb_try_idle(struct musb *musb, unsigned long timeout) { static unsigned long last_timer; @@ -282,7 +290,7 @@ void musb_platform_try_idle(struct musb *musb, unsigned long timeout) mod_timer(&otg_workaround, timeout); } -static irqreturn_t da8xx_interrupt(int irq, void *hci) +static irqreturn_t da8xx_musb_interrupt(int irq, void *hci) { struct musb *musb = hci; void __iomem *reg_base = musb->ctrl_base; @@ -380,7 +388,7 @@ static irqreturn_t da8xx_interrupt(int irq, void *hci) return ret; } -int musb_platform_set_mode(struct musb *musb, u8 musb_mode) +static int da8xx_musb_set_mode(struct musb *musb, u8 musb_mode) { u32 cfgchip2 = __raw_readl(CFGCHIP2); @@ -409,15 +417,13 @@ int musb_platform_set_mode(struct musb *musb, u8 musb_mode) return 0; } -int __init musb_platform_init(struct musb *musb, void *board_data) +static int da8xx_musb_init(struct musb *musb) { void __iomem *reg_base = musb->ctrl_base; u32 rev; musb->mregs += DA8XX_MENTOR_CORE_OFFSET; - clk_enable(musb->clock); - /* Returns zero if e.g. not clocked */ rev = musb_readl(reg_base, DA8XX_USB_REVISION_REG); if (!rev) @@ -431,8 +437,6 @@ int __init musb_platform_init(struct musb *musb, void *board_data) if (is_host_enabled(musb)) setup_timer(&otg_workaround, otg_timer, (unsigned long)musb); - musb->board_set_vbus = da8xx_set_vbus; - /* Reset the controller */ musb_writel(reg_base, DA8XX_USB_CTRL_REG, DA8XX_SOFT_RESET_MASK); @@ -446,14 +450,13 @@ int __init musb_platform_init(struct musb *musb, void *board_data) rev, __raw_readl(CFGCHIP2), musb_readb(reg_base, DA8XX_USB_CTRL_REG)); - musb->isr = da8xx_interrupt; + musb->isr = da8xx_musb_interrupt; return 0; fail: - clk_disable(musb->clock); return -ENODEV; } -int musb_platform_exit(struct musb *musb) +static int da8xx_musb_exit(struct musb *musb) { if (is_host_enabled(musb)) del_timer_sync(&otg_workaround); @@ -463,7 +466,140 @@ int musb_platform_exit(struct musb *musb) otg_put_transceiver(musb->xceiv); usb_nop_xceiv_unregister(); - clk_disable(musb->clock); + return 0; +} + +static const struct musb_platform_ops da8xx_ops = { + .init = da8xx_musb_init, + .exit = da8xx_musb_exit, + + .enable = da8xx_musb_enable, + .disable = da8xx_musb_disable, + + .set_mode = da8xx_musb_set_mode, + .try_idle = da8xx_musb_try_idle, + + .set_vbus = da8xx_musb_set_vbus, +}; + +static u64 da8xx_dmamask = DMA_BIT_MASK(32); + +static int __init da8xx_probe(struct platform_device *pdev) +{ + struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data; + struct platform_device *musb; + struct da8xx_glue *glue; + + struct clk *clk; + + int ret = -ENOMEM; + + glue = kzalloc(sizeof(*glue), GFP_KERNEL); + if (!glue) { + dev_err(&pdev->dev, "failed to allocate glue context\n"); + goto err0; + } + + musb = platform_device_alloc("musb-hdrc", -1); + if (!musb) { + dev_err(&pdev->dev, "failed to allocate musb device\n"); + goto err1; + } + + clk = clk_get(&pdev->dev, "usb20"); + if (IS_ERR(clk)) { + dev_err(&pdev->dev, "failed to get clock\n"); + ret = PTR_ERR(clk); + goto err2; + } + + ret = clk_enable(clk); + if (ret) { + dev_err(&pdev->dev, "failed to enable clock\n"); + goto err3; + } + + musb->dev.parent = &pdev->dev; + musb->dev.dma_mask = &da8xx_dmamask; + musb->dev.coherent_dma_mask = da8xx_dmamask; + + glue->dev = &pdev->dev; + glue->musb = musb; + glue->clk = clk; + + pdata->platform_ops = &da8xx_ops; + + platform_set_drvdata(pdev, glue); + + ret = platform_device_add_resources(musb, pdev->resource, + pdev->num_resources); + if (ret) { + dev_err(&pdev->dev, "failed to add resources\n"); + goto err4; + } + + ret = platform_device_add_data(musb, pdata, sizeof(*pdata)); + if (ret) { + dev_err(&pdev->dev, "failed to add platform_data\n"); + goto err4; + } + + ret = platform_device_add(musb); + if (ret) { + dev_err(&pdev->dev, "failed to register musb device\n"); + goto err4; + } + + return 0; + +err4: + clk_disable(clk); + +err3: + clk_put(clk); + +err2: + platform_device_put(musb); + +err1: + kfree(glue); + +err0: + return ret; +} + +static int __exit da8xx_remove(struct platform_device *pdev) +{ + struct da8xx_glue *glue = platform_get_drvdata(pdev); + + platform_device_del(glue->musb); + platform_device_put(glue->musb); + clk_disable(glue->clk); + clk_put(glue->clk); + kfree(glue); return 0; } + +static struct platform_driver da8xx_driver = { + .remove = __exit_p(da8xx_remove), + .driver = { + .name = "musb-da8xx", + }, +}; + +MODULE_DESCRIPTION("DA8xx/OMAP-L1x MUSB Glue Layer"); +MODULE_AUTHOR("Sergei Shtylyov <sshtylyov@ru.mvista.com>"); +MODULE_LICENSE("GPL v2"); + +static int __init da8xx_init(void) +{ + return platform_driver_probe(&da8xx_driver, da8xx_probe); +} +subsys_initcall(da8xx_init); + +static void __exit da8xx_exit(void) +{ + platform_driver_unregister(&da8xx_driver); +} +module_exit(da8xx_exit); diff --git a/drivers/usb/musb/davinci.c b/drivers/usb/musb/davinci.c index 6e67629f50cc..e6de097fb7e8 100644 --- a/drivers/usb/musb/davinci.c +++ b/drivers/usb/musb/davinci.c @@ -30,6 +30,8 @@ #include <linux/clk.h> #include <linux/io.h> #include <linux/gpio.h> +#include <linux/platform_device.h> +#include <linux/dma-mapping.h> #include <mach/hardware.h> #include <mach/memory.h> @@ -51,6 +53,12 @@ #define USB_PHY_CTRL IO_ADDRESS(USBPHY_CTL_PADDR) #define DM355_DEEPSLEEP IO_ADDRESS(DM355_DEEPSLEEP_PADDR) +struct davinci_glue { + struct device *dev; + struct platform_device *musb; + struct clk *clk; +}; + /* REVISIT (PM) we should be able to keep the PHY in low power mode most * of the time (24 MHZ oscillator and PLL off, etc) by setting POWER.D0 * and, when in host mode, autosuspending idle root ports... PHYPLLON @@ -83,7 +91,7 @@ static inline void phy_off(void) static int dma_off = 1; -void musb_platform_enable(struct musb *musb) +static void davinci_musb_enable(struct musb *musb) { u32 tmp, old, val; @@ -116,7 +124,7 @@ void musb_platform_enable(struct musb *musb) /* * Disable the HDRC and flush interrupts */ -void musb_platform_disable(struct musb *musb) +static void davinci_musb_disable(struct musb *musb) { /* because we don't set CTRLR.UINT, "important" to: * - not read/write INTRUSB/INTRUSBE @@ -167,7 +175,7 @@ static void evm_deferred_drvvbus(struct work_struct *ignored) #endif /* EVM */ -static void davinci_source_power(struct musb *musb, int is_on, int immediate) +static void davinci_musb_source_power(struct musb *musb, int is_on, int immediate) { #ifdef CONFIG_MACH_DAVINCI_EVM if (is_on) @@ -190,10 +198,10 @@ static void davinci_source_power(struct musb *musb, int is_on, int immediate) #endif } -static void davinci_set_vbus(struct musb *musb, int is_on) +static void davinci_musb_set_vbus(struct musb *musb, int is_on) { WARN_ON(is_on && is_peripheral_active(musb)); - davinci_source_power(musb, is_on, 0); + davinci_musb_source_power(musb, is_on, 0); } @@ -259,7 +267,7 @@ static void otg_timer(unsigned long _musb) spin_unlock_irqrestore(&musb->lock, flags); } -static irqreturn_t davinci_interrupt(int irq, void *__hci) +static irqreturn_t davinci_musb_interrupt(int irq, void *__hci) { unsigned long flags; irqreturn_t retval = IRQ_NONE; @@ -345,7 +353,7 @@ static irqreturn_t davinci_interrupt(int irq, void *__hci) /* NOTE: this must complete poweron within 100 msec * (OTG_TIME_A_WAIT_VRISE) but we don't check for that. */ - davinci_source_power(musb, drvvbus, 0); + davinci_musb_source_power(musb, drvvbus, 0); DBG(2, "VBUS %s (%s)%s, devctl %02x\n", drvvbus ? "on" : "off", otg_state_string(musb), @@ -370,13 +378,13 @@ static irqreturn_t davinci_interrupt(int irq, void *__hci) return retval; } -int musb_platform_set_mode(struct musb *musb, u8 mode) +static int davinci_musb_set_mode(struct musb *musb, u8 mode) { /* EVM can't do this (right?) */ return -EIO; } -int __init musb_platform_init(struct musb *musb, void *board_data) +static int davinci_musb_init(struct musb *musb) { void __iomem *tibase = musb->ctrl_base; u32 revision; @@ -388,8 +396,6 @@ int __init musb_platform_init(struct musb *musb, void *board_data) musb->mregs += DAVINCI_BASE_OFFSET; - clk_enable(musb->clock); - /* returns zero if e.g. not clocked */ revision = musb_readl(tibase, DAVINCI_USB_VERSION_REG); if (revision == 0) @@ -398,8 +404,7 @@ int __init musb_platform_init(struct musb *musb, void *board_data) if (is_host_enabled(musb)) setup_timer(&otg_workaround, otg_timer, (unsigned long) musb); - musb->board_set_vbus = davinci_set_vbus; - davinci_source_power(musb, 0, 1); + davinci_musb_source_power(musb, 0, 1); /* dm355 EVM swaps D+/D- for signal integrity, and * is clocked from the main 24 MHz crystal. @@ -440,18 +445,16 @@ int __init musb_platform_init(struct musb *musb, void *board_data) revision, __raw_readl(USB_PHY_CTRL), musb_readb(tibase, DAVINCI_USB_CTRL_REG)); - musb->isr = davinci_interrupt; + musb->isr = davinci_musb_interrupt; return 0; fail: - clk_disable(musb->clock); - otg_put_transceiver(musb->xceiv); usb_nop_xceiv_unregister(); return -ENODEV; } -int musb_platform_exit(struct musb *musb) +static int davinci_musb_exit(struct musb *musb) { if (is_host_enabled(musb)) del_timer_sync(&otg_workaround); @@ -465,7 +468,7 @@ int musb_platform_exit(struct musb *musb) __raw_writel(deepsleep, DM355_DEEPSLEEP); } - davinci_source_power(musb, 0 /*off*/, 1); + davinci_musb_source_power(musb, 0 /*off*/, 1); /* delay, to avoid problems with module reload */ if (is_host_enabled(musb) && musb->xceiv->default_a) { @@ -495,10 +498,141 @@ int musb_platform_exit(struct musb *musb) phy_off(); - clk_disable(musb->clock); - otg_put_transceiver(musb->xceiv); usb_nop_xceiv_unregister(); return 0; } + +static const struct musb_platform_ops davinci_ops = { + .init = davinci_musb_init, + .exit = davinci_musb_exit, + + .enable = davinci_musb_enable, + .disable = davinci_musb_disable, + + .set_mode = davinci_musb_set_mode, + + .set_vbus = davinci_musb_set_vbus, +}; + +static u64 davinci_dmamask = DMA_BIT_MASK(32); + +static int __init davinci_probe(struct platform_device *pdev) +{ + struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data; + struct platform_device *musb; + struct davinci_glue *glue; + struct clk *clk; + + int ret = -ENOMEM; + + glue = kzalloc(sizeof(*glue), GFP_KERNEL); + if (!glue) { + dev_err(&pdev->dev, "failed to allocate glue context\n"); + goto err0; + } + + musb = platform_device_alloc("musb-hdrc", -1); + if (!musb) { + dev_err(&pdev->dev, "failed to allocate musb device\n"); + goto err1; + } + + clk = clk_get(&pdev->dev, "usb"); + if (IS_ERR(clk)) { + dev_err(&pdev->dev, "failed to get clock\n"); + ret = PTR_ERR(clk); + goto err2; + } + + ret = clk_enable(clk); + if (ret) { + dev_err(&pdev->dev, "failed to enable clock\n"); + goto err3; + } + + musb->dev.parent = &pdev->dev; + musb->dev.dma_mask = &davinci_dmamask; + musb->dev.coherent_dma_mask = davinci_dmamask; + + glue->dev = &pdev->dev; + glue->musb = musb; + glue->clk = clk; + + pdata->platform_ops = &davinci_ops; + + platform_set_drvdata(pdev, glue); + + ret = platform_device_add_resources(musb, pdev->resource, + pdev->num_resources); + if (ret) { + dev_err(&pdev->dev, "failed to add resources\n"); + goto err4; + } + + ret = platform_device_add_data(musb, pdata, sizeof(*pdata)); + if (ret) { + dev_err(&pdev->dev, "failed to add platform_data\n"); + goto err4; + } + + ret = platform_device_add(musb); + if (ret) { + dev_err(&pdev->dev, "failed to register musb device\n"); + goto err4; + } + + return 0; + +err4: + clk_disable(clk); + +err3: + clk_put(clk); + +err2: + platform_device_put(musb); + +err1: + kfree(glue); + +err0: + return ret; +} + +static int __exit davinci_remove(struct platform_device *pdev) +{ + struct davinci_glue *glue = platform_get_drvdata(pdev); + + platform_device_del(glue->musb); + platform_device_put(glue->musb); + clk_disable(glue->clk); + clk_put(glue->clk); + kfree(glue); + + return 0; +} + +static struct platform_driver davinci_driver = { + .remove = __exit_p(davinci_remove), + .driver = { + .name = "musb-davinci", + }, +}; + +MODULE_DESCRIPTION("DaVinci MUSB Glue Layer"); +MODULE_AUTHOR("Felipe Balbi <balbi@ti.com>"); +MODULE_LICENSE("GPL v2"); + +static int __init davinci_init(void) +{ + return platform_driver_probe(&davinci_driver, davinci_probe); +} +subsys_initcall(davinci_init); + +static void __exit davinci_exit(void) +{ + platform_driver_unregister(&davinci_driver); +} +module_exit(davinci_exit); diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index 365a4fab5c64..07cf394e491b 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -99,19 +99,8 @@ #include <linux/platform_device.h> #include <linux/io.h> -#ifdef CONFIG_ARM -#include <mach/hardware.h> -#include <mach/memory.h> -#include <asm/mach-types.h> -#endif - #include "musb_core.h" - -#ifdef CONFIG_ARCH_DAVINCI -#include "davinci.h" -#endif - #define TA_WAIT_BCON(m) max_t(int, (m)->a_wait_bcon, OTG_TIME_A_WAIT_BCON) @@ -126,7 +115,7 @@ MODULE_PARM_DESC(debug, "Debug message level. Default = 0"); #define DRIVER_INFO DRIVER_DESC ", v" MUSB_VERSION -#define MUSB_DRIVER_NAME "musb_hdrc" +#define MUSB_DRIVER_NAME "musb-hdrc" const char musb_driver_name[] = MUSB_DRIVER_NAME; MODULE_DESCRIPTION(DRIVER_INFO); @@ -230,7 +219,7 @@ static struct otg_io_access_ops musb_ulpi_access = { /*-------------------------------------------------------------------------*/ -#if !defined(CONFIG_USB_TUSB6010) && !defined(CONFIG_BLACKFIN) +#if !defined(CONFIG_USB_MUSB_TUSB6010) && !defined(CONFIG_USB_MUSB_BLACKFIN) /* * Load an endpoint's FIFO @@ -390,7 +379,7 @@ void musb_otg_timer_func(unsigned long data) case OTG_STATE_A_SUSPEND: case OTG_STATE_A_WAIT_BCON: DBG(1, "HNP: %s timeout\n", otg_state_string(musb)); - musb_set_vbus(musb, 0); + musb_platform_set_vbus(musb, 0); musb->xceiv->state = OTG_STATE_A_WAIT_VFALL; break; default: @@ -571,7 +560,7 @@ static irqreturn_t musb_stage0_irq(struct musb *musb, u8 int_usb, musb->ep0_stage = MUSB_EP0_START; musb->xceiv->state = OTG_STATE_A_IDLE; MUSB_HST_MODE(musb); - musb_set_vbus(musb, 1); + musb_platform_set_vbus(musb, 1); handled = IRQ_HANDLED; } @@ -642,7 +631,7 @@ static irqreturn_t musb_stage0_irq(struct musb *musb, u8 int_usb, /* go through A_WAIT_VFALL then start a new session */ if (!ignore) - musb_set_vbus(musb, 0); + musb_platform_set_vbus(musb, 0); handled = IRQ_HANDLED; } @@ -1049,8 +1038,6 @@ static void musb_shutdown(struct platform_device *pdev) spin_lock_irqsave(&musb->lock, flags); musb_platform_disable(musb); musb_generic_disable(musb); - if (musb->clock) - clk_put(musb->clock); spin_unlock_irqrestore(&musb->lock, flags); if (!is_otg_enabled(musb) && is_host_enabled(musb)) @@ -1074,10 +1061,11 @@ static void musb_shutdown(struct platform_device *pdev) * We don't currently use dynamic fifo setup capability to do anything * more than selecting one of a bunch of predefined configurations. */ -#if defined(CONFIG_USB_TUSB6010) || \ - defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3) \ - || defined(CONFIG_ARCH_OMAP4) +#if defined(CONFIG_USB_MUSB_TUSB6010) || defined(CONFIG_USB_MUSB_OMAP2PLUS) \ + || defined(CONFIG_USB_MUSB_AM35X) static ushort __initdata fifo_mode = 4; +#elif defined(CONFIG_USB_MUSB_UX500) +static ushort __initdata fifo_mode = 5; #else static ushort __initdata fifo_mode = 2; #endif @@ -1501,7 +1489,7 @@ static int __init musb_core_init(u16 musb_type, struct musb *musb) struct musb_hw_ep *hw_ep = musb->endpoints + i; hw_ep->fifo = MUSB_FIFO_OFFSET(i) + mbase; -#ifdef CONFIG_USB_TUSB6010 +#ifdef CONFIG_USB_MUSB_TUSB6010 hw_ep->fifo_async = musb->async + 0x400 + MUSB_FIFO_OFFSET(i); hw_ep->fifo_sync = musb->sync + 0x400 + MUSB_FIFO_OFFSET(i); hw_ep->fifo_sync_va = @@ -1548,7 +1536,8 @@ static int __init musb_core_init(u16 musb_type, struct musb *musb) /*-------------------------------------------------------------------------*/ #if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3430) || \ - defined(CONFIG_ARCH_OMAP4) + defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_ARCH_U8500) || \ + defined(CONFIG_ARCH_U5500) static irqreturn_t generic_interrupt(int irq, void *__hci) { @@ -1904,6 +1893,7 @@ allocate_instance(struct device *dev, } musb->controller = dev; + return musb; } @@ -2000,30 +1990,14 @@ bad_config: spin_lock_init(&musb->lock); musb->board_mode = plat->mode; musb->board_set_power = plat->set_power; - musb->set_clock = plat->set_clock; musb->min_power = plat->min_power; - - /* Clock usage is chip-specific ... functional clock (DaVinci, - * OMAP2430), or PHY ref (some TUSB6010 boards). All this core - * code does is make sure a clock handle is available; platform - * code manages it during start/stop and suspend/resume. - */ - if (plat->clock) { - musb->clock = clk_get(dev, plat->clock); - if (IS_ERR(musb->clock)) { - status = PTR_ERR(musb->clock); - musb->clock = NULL; - goto fail1; - } - } + musb->ops = plat->platform_ops; /* The musb_platform_init() call: * - adjusts musb->mregs and musb->isr if needed, * - may initialize an integrated tranceiver * - initializes musb->xceiv, usually by otg_get_transceiver() - * - activates clocks. * - stops powering VBUS - * - assigns musb->board_set_vbus if host mode is enabled * * There are various transciever configurations. Blackfin, * DaVinci, TUSB60x0, and others integrate them. OMAP3 uses @@ -2031,9 +2005,9 @@ bad_config: * isp1504, non-OTG, etc) mostly hooking up through ULPI. */ musb->isr = generic_interrupt; - status = musb_platform_init(musb, plat->board_data); + status = musb_platform_init(musb); if (status < 0) - goto fail2; + goto fail1; if (!musb->isr) { status = -ENODEV; @@ -2186,10 +2160,6 @@ fail3: device_init_wakeup(dev, 0); musb_platform_exit(musb); -fail2: - if (musb->clock) - clk_put(musb->clock); - fail1: dev_err(musb->controller, "musb_init_controller failed with status %d\n", status); @@ -2215,7 +2185,7 @@ static u64 *orig_dma_mask; static int __init musb_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; - int irq = platform_get_irq(pdev, 0); + int irq = platform_get_irq_byname(pdev, "mc"); int status; struct resource *iomem; void __iomem *base; @@ -2265,144 +2235,138 @@ static int __exit musb_remove(struct platform_device *pdev) #ifdef CONFIG_PM -static struct musb_context_registers musb_context; - -void musb_save_context(struct musb *musb) +static void musb_save_context(struct musb *musb) { int i; void __iomem *musb_base = musb->mregs; void __iomem *epio; if (is_host_enabled(musb)) { - musb_context.frame = musb_readw(musb_base, MUSB_FRAME); - musb_context.testmode = musb_readb(musb_base, MUSB_TESTMODE); - musb_context.busctl = musb_read_ulpi_buscontrol(musb->mregs); + musb->context.frame = musb_readw(musb_base, MUSB_FRAME); + musb->context.testmode = musb_readb(musb_base, MUSB_TESTMODE); + musb->context.busctl = musb_read_ulpi_buscontrol(musb->mregs); } - musb_context.power = musb_readb(musb_base, MUSB_POWER); - musb_context.intrtxe = musb_readw(musb_base, MUSB_INTRTXE); - musb_context.intrrxe = musb_readw(musb_base, MUSB_INTRRXE); - musb_context.intrusbe = musb_readb(musb_base, MUSB_INTRUSBE); - musb_context.index = musb_readb(musb_base, MUSB_INDEX); - musb_context.devctl = musb_readb(musb_base, MUSB_DEVCTL); + musb->context.power = musb_readb(musb_base, MUSB_POWER); + musb->context.intrtxe = musb_readw(musb_base, MUSB_INTRTXE); + musb->context.intrrxe = musb_readw(musb_base, MUSB_INTRRXE); + musb->context.intrusbe = musb_readb(musb_base, MUSB_INTRUSBE); + musb->context.index = musb_readb(musb_base, MUSB_INDEX); + musb->context.devctl = musb_readb(musb_base, MUSB_DEVCTL); for (i = 0; i < musb->config->num_eps; ++i) { epio = musb->endpoints[i].regs; - musb_context.index_regs[i].txmaxp = + musb->context.index_regs[i].txmaxp = musb_readw(epio, MUSB_TXMAXP); - musb_context.index_regs[i].txcsr = + musb->context.index_regs[i].txcsr = musb_readw(epio, MUSB_TXCSR); - musb_context.index_regs[i].rxmaxp = + musb->context.index_regs[i].rxmaxp = musb_readw(epio, MUSB_RXMAXP); - musb_context.index_regs[i].rxcsr = + musb->context.index_regs[i].rxcsr = musb_readw(epio, MUSB_RXCSR); if (musb->dyn_fifo) { - musb_context.index_regs[i].txfifoadd = + musb->context.index_regs[i].txfifoadd = musb_read_txfifoadd(musb_base); - musb_context.index_regs[i].rxfifoadd = + musb->context.index_regs[i].rxfifoadd = musb_read_rxfifoadd(musb_base); - musb_context.index_regs[i].txfifosz = + musb->context.index_regs[i].txfifosz = musb_read_txfifosz(musb_base); - musb_context.index_regs[i].rxfifosz = + musb->context.index_regs[i].rxfifosz = musb_read_rxfifosz(musb_base); } if (is_host_enabled(musb)) { - musb_context.index_regs[i].txtype = + musb->context.index_regs[i].txtype = musb_readb(epio, MUSB_TXTYPE); - musb_context.index_regs[i].txinterval = + musb->context.index_regs[i].txinterval = musb_readb(epio, MUSB_TXINTERVAL); - musb_context.index_regs[i].rxtype = + musb->context.index_regs[i].rxtype = musb_readb(epio, MUSB_RXTYPE); - musb_context.index_regs[i].rxinterval = + musb->context.index_regs[i].rxinterval = musb_readb(epio, MUSB_RXINTERVAL); - musb_context.index_regs[i].txfunaddr = + musb->context.index_regs[i].txfunaddr = musb_read_txfunaddr(musb_base, i); - musb_context.index_regs[i].txhubaddr = + musb->context.index_regs[i].txhubaddr = musb_read_txhubaddr(musb_base, i); - musb_context.index_regs[i].txhubport = + musb->context.index_regs[i].txhubport = musb_read_txhubport(musb_base, i); - musb_context.index_regs[i].rxfunaddr = + musb->context.index_regs[i].rxfunaddr = musb_read_rxfunaddr(musb_base, i); - musb_context.index_regs[i].rxhubaddr = + musb->context.index_regs[i].rxhubaddr = musb_read_rxhubaddr(musb_base, i); - musb_context.index_regs[i].rxhubport = + musb->context.index_regs[i].rxhubport = musb_read_rxhubport(musb_base, i); } } - - musb_platform_save_context(musb, &musb_context); } -void musb_restore_context(struct musb *musb) +static void musb_restore_context(struct musb *musb) { int i; void __iomem *musb_base = musb->mregs; void __iomem *ep_target_regs; void __iomem *epio; - musb_platform_restore_context(musb, &musb_context); - if (is_host_enabled(musb)) { - musb_writew(musb_base, MUSB_FRAME, musb_context.frame); - musb_writeb(musb_base, MUSB_TESTMODE, musb_context.testmode); - musb_write_ulpi_buscontrol(musb->mregs, musb_context.busctl); + musb_writew(musb_base, MUSB_FRAME, musb->context.frame); + musb_writeb(musb_base, MUSB_TESTMODE, musb->context.testmode); + musb_write_ulpi_buscontrol(musb->mregs, musb->context.busctl); } - musb_writeb(musb_base, MUSB_POWER, musb_context.power); - musb_writew(musb_base, MUSB_INTRTXE, musb_context.intrtxe); - musb_writew(musb_base, MUSB_INTRRXE, musb_context.intrrxe); - musb_writeb(musb_base, MUSB_INTRUSBE, musb_context.intrusbe); - musb_writeb(musb_base, MUSB_DEVCTL, musb_context.devctl); + musb_writeb(musb_base, MUSB_POWER, musb->context.power); + musb_writew(musb_base, MUSB_INTRTXE, musb->context.intrtxe); + musb_writew(musb_base, MUSB_INTRRXE, musb->context.intrrxe); + musb_writeb(musb_base, MUSB_INTRUSBE, musb->context.intrusbe); + musb_writeb(musb_base, MUSB_DEVCTL, musb->context.devctl); for (i = 0; i < musb->config->num_eps; ++i) { epio = musb->endpoints[i].regs; musb_writew(epio, MUSB_TXMAXP, - musb_context.index_regs[i].txmaxp); + musb->context.index_regs[i].txmaxp); musb_writew(epio, MUSB_TXCSR, - musb_context.index_regs[i].txcsr); + musb->context.index_regs[i].txcsr); musb_writew(epio, MUSB_RXMAXP, - musb_context.index_regs[i].rxmaxp); + musb->context.index_regs[i].rxmaxp); musb_writew(epio, MUSB_RXCSR, - musb_context.index_regs[i].rxcsr); + musb->context.index_regs[i].rxcsr); if (musb->dyn_fifo) { musb_write_txfifosz(musb_base, - musb_context.index_regs[i].txfifosz); + musb->context.index_regs[i].txfifosz); musb_write_rxfifosz(musb_base, - musb_context.index_regs[i].rxfifosz); + musb->context.index_regs[i].rxfifosz); musb_write_txfifoadd(musb_base, - musb_context.index_regs[i].txfifoadd); + musb->context.index_regs[i].txfifoadd); musb_write_rxfifoadd(musb_base, - musb_context.index_regs[i].rxfifoadd); + musb->context.index_regs[i].rxfifoadd); } if (is_host_enabled(musb)) { musb_writeb(epio, MUSB_TXTYPE, - musb_context.index_regs[i].txtype); + musb->context.index_regs[i].txtype); musb_writeb(epio, MUSB_TXINTERVAL, - musb_context.index_regs[i].txinterval); + musb->context.index_regs[i].txinterval); musb_writeb(epio, MUSB_RXTYPE, - musb_context.index_regs[i].rxtype); + musb->context.index_regs[i].rxtype); musb_writeb(epio, MUSB_RXINTERVAL, - musb_context.index_regs[i].rxinterval); + musb->context.index_regs[i].rxinterval); musb_write_txfunaddr(musb_base, i, - musb_context.index_regs[i].txfunaddr); + musb->context.index_regs[i].txfunaddr); musb_write_txhubaddr(musb_base, i, - musb_context.index_regs[i].txhubaddr); + musb->context.index_regs[i].txhubaddr); musb_write_txhubport(musb_base, i, - musb_context.index_regs[i].txhubport); + musb->context.index_regs[i].txhubport); ep_target_regs = musb_read_target_reg_base(i, musb_base); musb_write_rxfunaddr(ep_target_regs, - musb_context.index_regs[i].rxfunaddr); + musb->context.index_regs[i].rxfunaddr); musb_write_rxhubaddr(ep_target_regs, - musb_context.index_regs[i].rxhubaddr); + musb->context.index_regs[i].rxhubaddr); musb_write_rxhubport(ep_target_regs, - musb_context.index_regs[i].rxhubport); + musb->context.index_regs[i].rxhubport); } } } @@ -2413,9 +2377,6 @@ static int musb_suspend(struct device *dev) unsigned long flags; struct musb *musb = dev_to_musb(&pdev->dev); - if (!musb->clock) - return 0; - spin_lock_irqsave(&musb->lock, flags); if (is_peripheral_active(musb)) { @@ -2430,10 +2391,6 @@ static int musb_suspend(struct device *dev) musb_save_context(musb); - if (musb->set_clock) - musb->set_clock(musb->clock, 0); - else - clk_disable(musb->clock); spin_unlock_irqrestore(&musb->lock, flags); return 0; } @@ -2443,14 +2400,6 @@ static int musb_resume_noirq(struct device *dev) struct platform_device *pdev = to_platform_device(dev); struct musb *musb = dev_to_musb(&pdev->dev); - if (!musb->clock) - return 0; - - if (musb->set_clock) - musb->set_clock(musb->clock, 1); - else - clk_enable(musb->clock); - musb_restore_context(musb); /* for static cmos like DaVinci, register values were preserved diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h index 69797e5b46a7..d0c236f8e191 100644 --- a/drivers/usb/musb/musb_core.h +++ b/drivers/usb/musb/musb_core.h @@ -222,7 +222,7 @@ enum musb_g_ep0_state { #endif /* TUSB mapping: "flat" plus ep0 special cases */ -#if defined(CONFIG_USB_TUSB6010) +#if defined(CONFIG_USB_MUSB_TUSB6010) #define musb_ep_select(_mbase, _epnum) \ musb_writeb((_mbase), MUSB_INDEX, (_epnum)) #define MUSB_EP_OFFSET MUSB_TUSB_OFFSET @@ -253,6 +253,29 @@ enum musb_g_ep0_state { /******************************** TYPES *************************************/ +/** + * struct musb_platform_ops - Operations passed to musb_core by HW glue layer + * @init: turns on clocks, sets up platform-specific registers, etc + * @exit: undoes @init + * @set_mode: forcefully changes operating mode + * @try_ilde: tries to idle the IP + * @vbus_status: returns vbus status if possible + * @set_vbus: forces vbus status + */ +struct musb_platform_ops { + int (*init)(struct musb *musb); + int (*exit)(struct musb *musb); + + void (*enable)(struct musb *musb); + void (*disable)(struct musb *musb); + + int (*set_mode)(struct musb *musb, u8 mode); + void (*try_idle)(struct musb *musb, unsigned long timeout); + + int (*vbus_status)(struct musb *musb); + void (*set_vbus)(struct musb *musb, int on); +}; + /* * struct musb_hw_ep - endpoint hardware (bidirectional) * @@ -263,7 +286,7 @@ struct musb_hw_ep { void __iomem *fifo; void __iomem *regs; -#ifdef CONFIG_USB_TUSB6010 +#ifdef CONFIG_USB_MUSB_TUSB6010 void __iomem *conf; #endif @@ -280,7 +303,7 @@ struct musb_hw_ep { struct dma_channel *tx_channel; struct dma_channel *rx_channel; -#ifdef CONFIG_USB_TUSB6010 +#ifdef CONFIG_USB_MUSB_TUSB6010 /* TUSB has "asynchronous" and "synchronous" dma modes */ dma_addr_t fifo_async; dma_addr_t fifo_sync; @@ -323,14 +346,43 @@ static inline struct usb_request *next_out_request(struct musb_hw_ep *hw_ep) #endif } +struct musb_csr_regs { + /* FIFO registers */ + u16 txmaxp, txcsr, rxmaxp, rxcsr; + u16 rxfifoadd, txfifoadd; + u8 txtype, txinterval, rxtype, rxinterval; + u8 rxfifosz, txfifosz; + u8 txfunaddr, txhubaddr, txhubport; + u8 rxfunaddr, rxhubaddr, rxhubport; +}; + +struct musb_context_registers { + +#if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3) || \ + defined(CONFIG_ARCH_OMAP4) + u32 otg_sysconfig, otg_forcestandby; +#endif + u8 power; + u16 intrtxe, intrrxe; + u8 intrusbe; + u16 frame; + u8 index, testmode; + + u8 devctl, busctl, misc; + + struct musb_csr_regs index_regs[MUSB_C_NUM_EPS]; +}; + /* * struct musb - Driver instance data. */ struct musb { /* device lock */ spinlock_t lock; - struct clk *clock; - struct clk *phy_clock; + + const struct musb_platform_ops *ops; + struct musb_context_registers context; + irqreturn_t (*isr)(int, void *); struct work_struct irq_work; u16 hwvers; @@ -359,11 +411,7 @@ struct musb { struct timer_list otg_timer; #endif - - /* called with IRQs blocked; ON/nonzero implies starting a session, - * and waiting at least a_wait_vrise_tmout. - */ - void (*board_set_vbus)(struct musb *, int is_on); + struct notifier_block nb; struct dma_controller *dma_controller; @@ -371,7 +419,7 @@ struct musb { void __iomem *ctrl_base; void __iomem *mregs; -#ifdef CONFIG_USB_TUSB6010 +#ifdef CONFIG_USB_MUSB_TUSB6010 dma_addr_t async; dma_addr_t sync; void __iomem *sync_va; @@ -398,8 +446,6 @@ struct musb { u8 board_mode; /* enum musb_mode */ int (*board_set_power)(int state); - int (*set_clock)(struct clk *clk, int is_active); - u8 min_power; /* vbus for periph, in mA/2 */ bool is_host; @@ -458,52 +504,6 @@ struct musb { #endif }; -#ifdef CONFIG_PM -struct musb_csr_regs { - /* FIFO registers */ - u16 txmaxp, txcsr, rxmaxp, rxcsr; - u16 rxfifoadd, txfifoadd; - u8 txtype, txinterval, rxtype, rxinterval; - u8 rxfifosz, txfifosz; - u8 txfunaddr, txhubaddr, txhubport; - u8 rxfunaddr, rxhubaddr, rxhubport; -}; - -struct musb_context_registers { - -#if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3) || \ - defined(CONFIG_ARCH_OMAP4) - u32 otg_sysconfig, otg_forcestandby; -#endif - u8 power; - u16 intrtxe, intrrxe; - u8 intrusbe; - u16 frame; - u8 index, testmode; - - u8 devctl, busctl, misc; - - struct musb_csr_regs index_regs[MUSB_C_NUM_EPS]; -}; - -#if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3) || \ - defined(CONFIG_ARCH_OMAP4) -extern void musb_platform_save_context(struct musb *musb, - struct musb_context_registers *musb_context); -extern void musb_platform_restore_context(struct musb *musb, - struct musb_context_registers *musb_context); -#else -#define musb_platform_save_context(m, x) do {} while (0) -#define musb_platform_restore_context(m, x) do {} while (0) -#endif - -#endif - -static inline void musb_set_vbus(struct musb *musb, int is_on) -{ - musb->board_set_vbus(musb, is_on); -} - #ifdef CONFIG_USB_GADGET_MUSB_HDRC static inline struct musb *gadget_to_musb(struct usb_gadget *g) { @@ -592,29 +592,63 @@ extern void musb_load_testpacket(struct musb *); extern irqreturn_t musb_interrupt(struct musb *); -extern void musb_platform_enable(struct musb *musb); -extern void musb_platform_disable(struct musb *musb); - extern void musb_hnp_stop(struct musb *musb); -extern int musb_platform_set_mode(struct musb *musb, u8 musb_mode); +static inline void musb_platform_set_vbus(struct musb *musb, int is_on) +{ + if (musb->ops->set_vbus) + musb->ops->set_vbus(musb, is_on); +} -#if defined(CONFIG_USB_TUSB6010) || defined(CONFIG_BLACKFIN) || \ - defined(CONFIG_ARCH_DAVINCI_DA8XX) || \ - defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3) || \ - defined(CONFIG_ARCH_OMAP4) -extern void musb_platform_try_idle(struct musb *musb, unsigned long timeout); -#else -#define musb_platform_try_idle(x, y) do {} while (0) -#endif +static inline void musb_platform_enable(struct musb *musb) +{ + if (musb->ops->enable) + musb->ops->enable(musb); +} -#if defined(CONFIG_USB_TUSB6010) || defined(CONFIG_BLACKFIN) -extern int musb_platform_get_vbus_status(struct musb *musb); -#else -#define musb_platform_get_vbus_status(x) 0 -#endif +static inline void musb_platform_disable(struct musb *musb) +{ + if (musb->ops->disable) + musb->ops->disable(musb); +} + +static inline int musb_platform_set_mode(struct musb *musb, u8 mode) +{ + if (!musb->ops->set_mode) + return 0; + + return musb->ops->set_mode(musb, mode); +} + +static inline void musb_platform_try_idle(struct musb *musb, + unsigned long timeout) +{ + if (musb->ops->try_idle) + musb->ops->try_idle(musb, timeout); +} + +static inline int musb_platform_get_vbus_status(struct musb *musb) +{ + if (!musb->ops->vbus_status) + return 0; -extern int __init musb_platform_init(struct musb *musb, void *board_data); -extern int musb_platform_exit(struct musb *musb); + return musb->ops->vbus_status(musb); +} + +static inline int musb_platform_init(struct musb *musb) +{ + if (!musb->ops->init) + return -EINVAL; + + return musb->ops->init(musb); +} + +static inline int musb_platform_exit(struct musb *musb) +{ + if (!musb->ops->exit) + return -EINVAL; + + return musb->ops->exit(musb); +} #endif /* __MUSB_CORE_H__ */ diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c index 9d6ade82b9f2..9b162dfaa4fb 100644 --- a/drivers/usb/musb/musb_gadget.c +++ b/drivers/usb/musb/musb_gadget.c @@ -1136,13 +1136,16 @@ struct usb_request *musb_alloc_request(struct usb_ep *ep, gfp_t gfp_flags) struct musb_request *request = NULL; request = kzalloc(sizeof *request, gfp_flags); - if (request) { - INIT_LIST_HEAD(&request->request.list); - request->request.dma = DMA_ADDR_INVALID; - request->epnum = musb_ep->current_epnum; - request->ep = musb_ep; + if (!request) { + DBG(4, "not enough memory\n"); + return NULL; } + INIT_LIST_HEAD(&request->request.list); + request->request.dma = DMA_ADDR_INVALID; + request->epnum = musb_ep->current_epnum; + request->ep = musb_ep; + return &request->request; } diff --git a/drivers/usb/musb/musb_io.h b/drivers/usb/musb/musb_io.h index b06e9ef00cfc..03c6ccdbb3be 100644 --- a/drivers/usb/musb/musb_io.h +++ b/drivers/usb/musb/musb_io.h @@ -74,7 +74,7 @@ static inline void musb_writel(void __iomem *addr, unsigned offset, u32 data) { __raw_writel(data, addr + offset); } -#ifdef CONFIG_USB_TUSB6010 +#ifdef CONFIG_USB_MUSB_TUSB6010 /* * TUSB6010 doesn't allow 8-bit access; 16-bit access is the minimum. @@ -114,7 +114,7 @@ static inline u8 musb_readb(const void __iomem *addr, unsigned offset) static inline void musb_writeb(void __iomem *addr, unsigned offset, u8 data) { __raw_writeb(data, addr + offset); } -#endif /* CONFIG_USB_TUSB6010 */ +#endif /* CONFIG_USB_MUSB_TUSB6010 */ #else diff --git a/drivers/usb/musb/musb_regs.h b/drivers/usb/musb/musb_regs.h index 5a727c5b8676..82410703dcd3 100644 --- a/drivers/usb/musb/musb_regs.h +++ b/drivers/usb/musb/musb_regs.h @@ -234,7 +234,7 @@ #define MUSB_TESTMODE 0x0F /* 8 bit */ /* Get offset for a given FIFO from musb->mregs */ -#ifdef CONFIG_USB_TUSB6010 +#ifdef CONFIG_USB_MUSB_TUSB6010 #define MUSB_FIFO_OFFSET(epnum) (0x200 + ((epnum) * 0x20)) #else #define MUSB_FIFO_OFFSET(epnum) (0x20 + ((epnum) * 4)) @@ -295,7 +295,7 @@ #define MUSB_FLAT_OFFSET(_epnum, _offset) \ (0x100 + (0x10*(_epnum)) + (_offset)) -#ifdef CONFIG_USB_TUSB6010 +#ifdef CONFIG_USB_MUSB_TUSB6010 /* TUSB6010 EP0 configuration register is special */ #define MUSB_TUSB_OFFSET(_epnum, _offset) \ (0x10 + _offset) diff --git a/drivers/usb/musb/musb_virthub.c b/drivers/usb/musb/musb_virthub.c index 43233c397b6e..b46d1877e28e 100644 --- a/drivers/usb/musb/musb_virthub.c +++ b/drivers/usb/musb/musb_virthub.c @@ -276,7 +276,7 @@ int musb_hub_control( break; case USB_PORT_FEAT_POWER: if (!(is_otg_enabled(musb) && hcd->self.is_b_host)) - musb_set_vbus(musb, 0); + musb_platform_set_vbus(musb, 0); break; case USB_PORT_FEAT_C_CONNECTION: case USB_PORT_FEAT_C_ENABLE: diff --git a/drivers/usb/musb/musbhsdma.c b/drivers/usb/musb/musbhsdma.c index 563114d613d6..0144a2d481fd 100644 --- a/drivers/usb/musb/musbhsdma.c +++ b/drivers/usb/musb/musbhsdma.c @@ -377,7 +377,7 @@ dma_controller_create(struct musb *musb, void __iomem *base) struct musb_dma_controller *controller; struct device *dev = musb->controller; struct platform_device *pdev = to_platform_device(dev); - int irq = platform_get_irq(pdev, 1); + int irq = platform_get_irq_byname(pdev, "dma"); if (irq == 0) { dev_err(dev, "No DMA interrupt line!\n"); diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c index ed618bde1eec..a3f12333fc41 100644 --- a/drivers/usb/musb/omap2430.c +++ b/drivers/usb/musb/omap2430.c @@ -31,10 +31,18 @@ #include <linux/list.h> #include <linux/clk.h> #include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/dma-mapping.h> #include "musb_core.h" #include "omap2430.h" +struct omap2430_glue { + struct device *dev; + struct platform_device *musb; + struct clk *clk; +}; +#define glue_to_musb(g) platform_get_drvdata(g->musb) static struct timer_list musb_idle_timer; @@ -49,12 +57,8 @@ static void musb_do_idle(unsigned long _musb) spin_lock_irqsave(&musb->lock, flags); - devctl = musb_readb(musb->mregs, MUSB_DEVCTL); - switch (musb->xceiv->state) { case OTG_STATE_A_WAIT_BCON: - devctl &= ~MUSB_DEVCTL_SESSION; - musb_writeb(musb->mregs, MUSB_DEVCTL, devctl); devctl = musb_readb(musb->mregs, MUSB_DEVCTL); if (devctl & MUSB_DEVCTL_BDEVICE) { @@ -98,7 +102,7 @@ static void musb_do_idle(unsigned long _musb) } -void musb_platform_try_idle(struct musb *musb, unsigned long timeout) +static void omap2430_musb_try_idle(struct musb *musb, unsigned long timeout) { unsigned long default_timeout = jiffies + msecs_to_jiffies(3); static unsigned long last_timer; @@ -131,15 +135,11 @@ void musb_platform_try_idle(struct musb *musb, unsigned long timeout) mod_timer(&musb_idle_timer, timeout); } -void musb_platform_enable(struct musb *musb) -{ -} -void musb_platform_disable(struct musb *musb) -{ -} -static void omap_set_vbus(struct musb *musb, int is_on) +static void omap2430_musb_set_vbus(struct musb *musb, int is_on) { u8 devctl; + unsigned long timeout = jiffies + msecs_to_jiffies(1000); + int ret = 1; /* HDRC controls CPEN, but beware current surges during device * connect. They can trigger transient overcurrent conditions * that must be ignored. @@ -148,12 +148,35 @@ static void omap_set_vbus(struct musb *musb, int is_on) devctl = musb_readb(musb->mregs, MUSB_DEVCTL); if (is_on) { - musb->is_active = 1; - musb->xceiv->default_a = 1; - musb->xceiv->state = OTG_STATE_A_WAIT_VRISE; - devctl |= MUSB_DEVCTL_SESSION; - - MUSB_HST_MODE(musb); + if (musb->xceiv->state == OTG_STATE_A_IDLE) { + /* start the session */ + devctl |= MUSB_DEVCTL_SESSION; + musb_writeb(musb->mregs, MUSB_DEVCTL, devctl); + /* + * Wait for the musb to set as A device to enable the + * VBUS + */ + while (musb_readb(musb->mregs, MUSB_DEVCTL) & 0x80) { + + cpu_relax(); + + if (time_after(jiffies, timeout)) { + dev_err(musb->controller, + "configured as A device timeout"); + ret = -EINVAL; + break; + } + } + + if (ret && musb->xceiv->set_vbus) + otg_set_vbus(musb->xceiv, 1); + } else { + musb->is_active = 1; + musb->xceiv->default_a = 1; + musb->xceiv->state = OTG_STATE_A_WAIT_VRISE; + devctl |= MUSB_DEVCTL_SESSION; + MUSB_HST_MODE(musb); + } } else { musb->is_active = 0; @@ -175,9 +198,7 @@ static void omap_set_vbus(struct musb *musb, int is_on) musb_readb(musb->mregs, MUSB_DEVCTL)); } -static int musb_platform_resume(struct musb *musb); - -int musb_platform_set_mode(struct musb *musb, u8 musb_mode) +static int omap2430_musb_set_mode(struct musb *musb, u8 musb_mode) { u8 devctl = musb_readb(musb->mregs, MUSB_DEVCTL); @@ -187,10 +208,94 @@ int musb_platform_set_mode(struct musb *musb, u8 musb_mode) return 0; } -int __init musb_platform_init(struct musb *musb, void *board_data) +static inline void omap2430_low_level_exit(struct musb *musb) { u32 l; - struct omap_musb_board_data *data = board_data; + + /* in any role */ + l = musb_readl(musb->mregs, OTG_FORCESTDBY); + l |= ENABLEFORCE; /* enable MSTANDBY */ + musb_writel(musb->mregs, OTG_FORCESTDBY, l); + + l = musb_readl(musb->mregs, OTG_SYSCONFIG); + l |= ENABLEWAKEUP; /* enable wakeup */ + musb_writel(musb->mregs, OTG_SYSCONFIG, l); +} + +static inline void omap2430_low_level_init(struct musb *musb) +{ + u32 l; + + l = musb_readl(musb->mregs, OTG_SYSCONFIG); + l &= ~ENABLEWAKEUP; /* disable wakeup */ + musb_writel(musb->mregs, OTG_SYSCONFIG, l); + + l = musb_readl(musb->mregs, OTG_FORCESTDBY); + l &= ~ENABLEFORCE; /* disable MSTANDBY */ + musb_writel(musb->mregs, OTG_FORCESTDBY, l); +} + +/* blocking notifier support */ +static int musb_otg_notifications(struct notifier_block *nb, + unsigned long event, void *unused) +{ + struct musb *musb = container_of(nb, struct musb, nb); + struct device *dev = musb->controller; + struct musb_hdrc_platform_data *pdata = dev->platform_data; + struct omap_musb_board_data *data = pdata->board_data; + + switch (event) { + case USB_EVENT_ID: + DBG(4, "ID GND\n"); + + if (is_otg_enabled(musb)) { +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + if (musb->gadget_driver) { + otg_init(musb->xceiv); + + if (data->interface_type == + MUSB_INTERFACE_UTMI) + omap2430_musb_set_vbus(musb, 1); + + } +#endif + } else { + otg_init(musb->xceiv); + if (data->interface_type == + MUSB_INTERFACE_UTMI) + omap2430_musb_set_vbus(musb, 1); + } + break; + + case USB_EVENT_VBUS: + DBG(4, "VBUS Connect\n"); + + otg_init(musb->xceiv); + break; + + case USB_EVENT_NONE: + DBG(4, "VBUS Disconnect\n"); + + if (data->interface_type == MUSB_INTERFACE_UTMI) { + if (musb->xceiv->set_vbus) + otg_set_vbus(musb->xceiv, 0); + } + otg_shutdown(musb->xceiv); + break; + default: + DBG(4, "ID float\n"); + return NOTIFY_DONE; + } + + return NOTIFY_OK; +} + +static int omap2430_musb_init(struct musb *musb) +{ + u32 l, status = 0; + struct device *dev = musb->controller; + struct musb_hdrc_platform_data *plat = dev->platform_data; + struct omap_musb_board_data *data = plat->board_data; /* We require some kind of external transceiver, hooked * up through ULPI. TWL4030-family PMICs include one, @@ -202,7 +307,7 @@ int __init musb_platform_init(struct musb *musb, void *board_data) return -ENODEV; } - musb_platform_resume(musb); + omap2430_low_level_init(musb); l = musb_readl(musb->mregs, OTG_SYSCONFIG); l &= ~ENABLEWAKEUP; /* disable wakeup */ @@ -239,87 +344,214 @@ int __init musb_platform_init(struct musb *musb, void *board_data) musb_readl(musb->mregs, OTG_INTERFSEL), musb_readl(musb->mregs, OTG_SIMENABLE)); - if (is_host_enabled(musb)) - musb->board_set_vbus = omap_set_vbus; + musb->nb.notifier_call = musb_otg_notifications; + status = otg_register_notifier(musb->xceiv, &musb->nb); + + if (status) + DBG(1, "notification register failed\n"); + + /* check whether cable is already connected */ + if (musb->xceiv->state ==OTG_STATE_B_IDLE) + musb_otg_notifications(&musb->nb, 1, + musb->xceiv->gadget); setup_timer(&musb_idle_timer, musb_do_idle, (unsigned long) musb); return 0; } -#ifdef CONFIG_PM -void musb_platform_save_context(struct musb *musb, - struct musb_context_registers *musb_context) +static int omap2430_musb_exit(struct musb *musb) { - musb_context->otg_sysconfig = musb_readl(musb->mregs, OTG_SYSCONFIG); - musb_context->otg_forcestandby = musb_readl(musb->mregs, OTG_FORCESTDBY); -} -void musb_platform_restore_context(struct musb *musb, - struct musb_context_registers *musb_context) -{ - musb_writel(musb->mregs, OTG_SYSCONFIG, musb_context->otg_sysconfig); - musb_writel(musb->mregs, OTG_FORCESTDBY, musb_context->otg_forcestandby); + omap2430_low_level_exit(musb); + otg_put_transceiver(musb->xceiv); + + return 0; } -#endif -static int musb_platform_suspend(struct musb *musb) +static const struct musb_platform_ops omap2430_ops = { + .init = omap2430_musb_init, + .exit = omap2430_musb_exit, + + .set_mode = omap2430_musb_set_mode, + .try_idle = omap2430_musb_try_idle, + + .set_vbus = omap2430_musb_set_vbus, +}; + +static u64 omap2430_dmamask = DMA_BIT_MASK(32); + +static int __init omap2430_probe(struct platform_device *pdev) { - u32 l; + struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data; + struct platform_device *musb; + struct omap2430_glue *glue; + struct clk *clk; - if (!musb->clock) - return 0; + int ret = -ENOMEM; - /* in any role */ - l = musb_readl(musb->mregs, OTG_FORCESTDBY); - l |= ENABLEFORCE; /* enable MSTANDBY */ - musb_writel(musb->mregs, OTG_FORCESTDBY, l); + glue = kzalloc(sizeof(*glue), GFP_KERNEL); + if (!glue) { + dev_err(&pdev->dev, "failed to allocate glue context\n"); + goto err0; + } - l = musb_readl(musb->mregs, OTG_SYSCONFIG); - l |= ENABLEWAKEUP; /* enable wakeup */ - musb_writel(musb->mregs, OTG_SYSCONFIG, l); + musb = platform_device_alloc("musb-hdrc", -1); + if (!musb) { + dev_err(&pdev->dev, "failed to allocate musb device\n"); + goto err1; + } - otg_set_suspend(musb->xceiv, 1); + clk = clk_get(&pdev->dev, "ick"); + if (IS_ERR(clk)) { + dev_err(&pdev->dev, "failed to get clock\n"); + ret = PTR_ERR(clk); + goto err2; + } - if (musb->set_clock) - musb->set_clock(musb->clock, 0); - else - clk_disable(musb->clock); + ret = clk_enable(clk); + if (ret) { + dev_err(&pdev->dev, "failed to enable clock\n"); + goto err3; + } + + musb->dev.parent = &pdev->dev; + musb->dev.dma_mask = &omap2430_dmamask; + musb->dev.coherent_dma_mask = omap2430_dmamask; + + glue->dev = &pdev->dev; + glue->musb = musb; + glue->clk = clk; + + pdata->platform_ops = &omap2430_ops; + + platform_set_drvdata(pdev, glue); + + ret = platform_device_add_resources(musb, pdev->resource, + pdev->num_resources); + if (ret) { + dev_err(&pdev->dev, "failed to add resources\n"); + goto err4; + } + + ret = platform_device_add_data(musb, pdata, sizeof(*pdata)); + if (ret) { + dev_err(&pdev->dev, "failed to add platform_data\n"); + goto err4; + } + + ret = platform_device_add(musb); + if (ret) { + dev_err(&pdev->dev, "failed to register musb device\n"); + goto err4; + } return 0; + +err4: + clk_disable(clk); + +err3: + clk_put(clk); + +err2: + platform_device_put(musb); + +err1: + kfree(glue); + +err0: + return ret; } -static int musb_platform_resume(struct musb *musb) +static int __exit omap2430_remove(struct platform_device *pdev) { - u32 l; + struct omap2430_glue *glue = platform_get_drvdata(pdev); - if (!musb->clock) - return 0; + platform_device_del(glue->musb); + platform_device_put(glue->musb); + clk_disable(glue->clk); + clk_put(glue->clk); + kfree(glue); - otg_set_suspend(musb->xceiv, 0); + return 0; +} - if (musb->set_clock) - musb->set_clock(musb->clock, 1); - else - clk_enable(musb->clock); +#ifdef CONFIG_PM +static void omap2430_save_context(struct musb *musb) +{ + musb->context.otg_sysconfig = musb_readl(musb->mregs, OTG_SYSCONFIG); + musb->context.otg_forcestandby = musb_readl(musb->mregs, OTG_FORCESTDBY); +} - l = musb_readl(musb->mregs, OTG_SYSCONFIG); - l &= ~ENABLEWAKEUP; /* disable wakeup */ - musb_writel(musb->mregs, OTG_SYSCONFIG, l); +static void omap2430_restore_context(struct musb *musb) +{ + musb_writel(musb->mregs, OTG_SYSCONFIG, musb->context.otg_sysconfig); + musb_writel(musb->mregs, OTG_FORCESTDBY, musb->context.otg_forcestandby); +} - l = musb_readl(musb->mregs, OTG_FORCESTDBY); - l &= ~ENABLEFORCE; /* disable MSTANDBY */ - musb_writel(musb->mregs, OTG_FORCESTDBY, l); +static int omap2430_suspend(struct device *dev) +{ + struct omap2430_glue *glue = dev_get_drvdata(dev); + struct musb *musb = glue_to_musb(glue); + + omap2430_low_level_exit(musb); + otg_set_suspend(musb->xceiv, 1); + omap2430_save_context(musb); + clk_disable(glue->clk); return 0; } - -int musb_platform_exit(struct musb *musb) +static int omap2430_resume(struct device *dev) { + struct omap2430_glue *glue = dev_get_drvdata(dev); + struct musb *musb = glue_to_musb(glue); + int ret; + + ret = clk_enable(glue->clk); + if (ret) { + dev_err(dev, "faled to enable clock\n"); + return ret; + } - musb_platform_suspend(musb); + omap2430_low_level_init(musb); + omap2430_restore_context(musb); + otg_set_suspend(musb->xceiv, 0); - otg_put_transceiver(musb->xceiv); return 0; } + +static struct dev_pm_ops omap2430_pm_ops = { + .suspend = omap2430_suspend, + .resume = omap2430_resume, +}; + +#define DEV_PM_OPS (&omap2430_pm_ops) +#else +#define DEV_PM_OPS NULL +#endif + +static struct platform_driver omap2430_driver = { + .remove = __exit_p(omap2430_remove), + .driver = { + .name = "musb-omap2430", + .pm = DEV_PM_OPS, + }, +}; + +MODULE_DESCRIPTION("OMAP2PLUS MUSB Glue Layer"); +MODULE_AUTHOR("Felipe Balbi <balbi@ti.com>"); +MODULE_LICENSE("GPL v2"); + +static int __init omap2430_init(void) +{ + return platform_driver_probe(&omap2430_driver, omap2430_probe); +} +subsys_initcall(omap2430_init); + +static void __exit omap2430_exit(void) +{ + platform_driver_unregister(&omap2430_driver); +} +module_exit(omap2430_exit); diff --git a/drivers/usb/musb/tusb6010.c b/drivers/usb/musb/tusb6010.c index bde40efc7046..2ba3b070ed0b 100644 --- a/drivers/usb/musb/tusb6010.c +++ b/drivers/usb/musb/tusb6010.c @@ -21,10 +21,16 @@ #include <linux/usb.h> #include <linux/irq.h> #include <linux/platform_device.h> +#include <linux/dma-mapping.h> #include "musb_core.h" -static void tusb_source_power(struct musb *musb, int is_on); +struct tusb6010_glue { + struct device *dev; + struct platform_device *musb; +}; + +static void tusb_musb_set_vbus(struct musb *musb, int is_on); #define TUSB_REV_MAJOR(reg_val) ((reg_val >> 4) & 0xf) #define TUSB_REV_MINOR(reg_val) (reg_val & 0xf) @@ -50,7 +56,7 @@ u8 tusb_get_revision(struct musb *musb) return rev; } -static int __init tusb_print_revision(struct musb *musb) +static int tusb_print_revision(struct musb *musb) { void __iomem *tbase = musb->ctrl_base; u8 rev; @@ -275,17 +281,6 @@ static int tusb_draw_power(struct otg_transceiver *x, unsigned mA) void __iomem *tbase = musb->ctrl_base; u32 reg; - /* - * Keep clock active when enabled. Note that this is not tied to - * drawing VBUS, as with OTG mA can be less than musb->min_power. - */ - if (musb->set_clock) { - if (mA) - musb->set_clock(musb->clock, 1); - else - musb->set_clock(musb->clock, 0); - } - /* tps65030 seems to consume max 100mA, with maybe 60mA available * (measured on one board) for things other than tps and tusb. * @@ -348,7 +343,7 @@ static void tusb_set_clock_source(struct musb *musb, unsigned mode) * USB link is not suspended ... and tells us the relevant wakeup * events. SW_EN for voltage is handled separately. */ -void tusb_allow_idle(struct musb *musb, u32 wakeup_enables) +static void tusb_allow_idle(struct musb *musb, u32 wakeup_enables) { void __iomem *tbase = musb->ctrl_base; u32 reg; @@ -385,7 +380,7 @@ void tusb_allow_idle(struct musb *musb, u32 wakeup_enables) /* * Updates cable VBUS status. Caller must take care of locking. */ -int musb_platform_get_vbus_status(struct musb *musb) +static int tusb_musb_vbus_status(struct musb *musb) { void __iomem *tbase = musb->ctrl_base; u32 otg_stat, prcm_mngmt; @@ -431,7 +426,7 @@ static void musb_do_idle(unsigned long _musb) } /* FALLTHROUGH */ case OTG_STATE_A_IDLE: - tusb_source_power(musb, 0); + tusb_musb_set_vbus(musb, 0); default: break; } @@ -475,7 +470,7 @@ done: * we don't want to treat that full speed J as a wakeup event. * ... peripherals must draw only suspend current after 10 msec. */ -void musb_platform_try_idle(struct musb *musb, unsigned long timeout) +static void tusb_musb_try_idle(struct musb *musb, unsigned long timeout) { unsigned long default_timeout = jiffies + msecs_to_jiffies(3); static unsigned long last_timer; @@ -515,7 +510,7 @@ void musb_platform_try_idle(struct musb *musb, unsigned long timeout) | TUSB_DEV_OTG_TIMER_ENABLE) \ : 0) -static void tusb_source_power(struct musb *musb, int is_on) +static void tusb_musb_set_vbus(struct musb *musb, int is_on) { void __iomem *tbase = musb->ctrl_base; u32 conf, prcm, timer; @@ -531,8 +526,6 @@ static void tusb_source_power(struct musb *musb, int is_on) devctl = musb_readb(musb->mregs, MUSB_DEVCTL); if (is_on) { - if (musb->set_clock) - musb->set_clock(musb->clock, 1); timer = OTG_TIMER_MS(OTG_TIME_A_WAIT_VRISE); musb->xceiv->default_a = 1; musb->xceiv->state = OTG_STATE_A_WAIT_VRISE; @@ -571,8 +564,6 @@ static void tusb_source_power(struct musb *musb, int is_on) devctl &= ~MUSB_DEVCTL_SESSION; conf &= ~TUSB_DEV_CONF_USB_HOST_MODE; - if (musb->set_clock) - musb->set_clock(musb->clock, 0); } prcm &= ~(TUSB_PRCM_MNGMT_15_SW_EN | TUSB_PRCM_MNGMT_33_SW_EN); @@ -599,7 +590,7 @@ static void tusb_source_power(struct musb *musb, int is_on) * and peripheral modes in non-OTG configurations by reconfiguring hardware * and then setting musb->board_mode. For now, only support OTG mode. */ -int musb_platform_set_mode(struct musb *musb, u8 musb_mode) +static int tusb_musb_set_mode(struct musb *musb, u8 musb_mode) { void __iomem *tbase = musb->ctrl_base; u32 otg_stat, phy_otg_ctrl, phy_otg_ena, dev_conf; @@ -677,7 +668,7 @@ tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase) default_a = is_host_enabled(musb); DBG(2, "Default-%c\n", default_a ? 'A' : 'B'); musb->xceiv->default_a = default_a; - tusb_source_power(musb, default_a); + tusb_musb_set_vbus(musb, default_a); /* Don't allow idling immediately */ if (default_a) @@ -722,7 +713,7 @@ tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase) switch (musb->xceiv->state) { case OTG_STATE_A_IDLE: DBG(2, "Got SRP, turning on VBUS\n"); - musb_set_vbus(musb, 1); + musb_platform_set_vbus(musb, 1); /* CONNECT can wake if a_wait_bcon is set */ if (musb->a_wait_bcon != 0) @@ -748,11 +739,11 @@ tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase) */ if (musb->vbuserr_retry) { musb->vbuserr_retry--; - tusb_source_power(musb, 1); + tusb_musb_set_vbus(musb, 1); } else { musb->vbuserr_retry = VBUSERR_RETRY_COUNT; - tusb_source_power(musb, 0); + tusb_musb_set_vbus(musb, 0); } break; default: @@ -786,7 +777,7 @@ tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase) } else { /* REVISIT report overcurrent to hub? */ ERR("vbus too slow, devctl %02x\n", devctl); - tusb_source_power(musb, 0); + tusb_musb_set_vbus(musb, 0); } break; case OTG_STATE_A_WAIT_BCON: @@ -807,7 +798,7 @@ tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase) return idle_timeout; } -static irqreturn_t tusb_interrupt(int irq, void *__hci) +static irqreturn_t tusb_musb_interrupt(int irq, void *__hci) { struct musb *musb = __hci; void __iomem *tbase = musb->ctrl_base; @@ -911,7 +902,7 @@ static irqreturn_t tusb_interrupt(int irq, void *__hci) musb_writel(tbase, TUSB_INT_SRC_CLEAR, int_src & ~TUSB_INT_MASK_RESERVED_BITS); - musb_platform_try_idle(musb, idle_timeout); + tusb_musb_try_idle(musb, idle_timeout); musb_writel(tbase, TUSB_INT_MASK, int_mask); spin_unlock_irqrestore(&musb->lock, flags); @@ -926,7 +917,7 @@ static int dma_off; * REVISIT: * - Check what is unnecessary in MGC_HdrcStart() */ -void musb_platform_enable(struct musb *musb) +static void tusb_musb_enable(struct musb *musb) { void __iomem *tbase = musb->ctrl_base; @@ -970,7 +961,7 @@ void musb_platform_enable(struct musb *musb) /* * Disables TUSB6010. Caller must take care of locking. */ -void musb_platform_disable(struct musb *musb) +static void tusb_musb_disable(struct musb *musb) { void __iomem *tbase = musb->ctrl_base; @@ -995,7 +986,7 @@ void musb_platform_disable(struct musb *musb) * Sets up TUSB6010 CPU interface specific signals and registers * Note: Settings optimized for OMAP24xx */ -static void __init tusb_setup_cpu_interface(struct musb *musb) +static void tusb_setup_cpu_interface(struct musb *musb) { void __iomem *tbase = musb->ctrl_base; @@ -1022,7 +1013,7 @@ static void __init tusb_setup_cpu_interface(struct musb *musb) musb_writel(tbase, TUSB_WAIT_COUNT, 1); } -static int __init tusb_start(struct musb *musb) +static int tusb_musb_start(struct musb *musb) { void __iomem *tbase = musb->ctrl_base; int ret = 0; @@ -1091,7 +1082,7 @@ err: return -ENODEV; } -int __init musb_platform_init(struct musb *musb, void *board_data) +static int tusb_musb_init(struct musb *musb) { struct platform_device *pdev; struct resource *mem; @@ -1131,16 +1122,14 @@ int __init musb_platform_init(struct musb *musb, void *board_data) */ musb->mregs += TUSB_BASE_OFFSET; - ret = tusb_start(musb); + ret = tusb_musb_start(musb); if (ret) { printk(KERN_ERR "Could not start tusb6010 (%d)\n", ret); goto done; } - musb->isr = tusb_interrupt; + musb->isr = tusb_musb_interrupt; - if (is_host_enabled(musb)) - musb->board_set_vbus = tusb_source_power; if (is_peripheral_enabled(musb)) { musb->xceiv->set_power = tusb_draw_power; the_musb = musb; @@ -1159,7 +1148,7 @@ done: return ret; } -int musb_platform_exit(struct musb *musb) +static int tusb_musb_exit(struct musb *musb) { del_timer_sync(&musb_idle_timer); the_musb = NULL; @@ -1173,3 +1162,115 @@ int musb_platform_exit(struct musb *musb) usb_nop_xceiv_unregister(); return 0; } + +static const struct musb_platform_ops tusb_ops = { + .init = tusb_musb_init, + .exit = tusb_musb_exit, + + .enable = tusb_musb_enable, + .disable = tusb_musb_disable, + + .set_mode = tusb_musb_set_mode, + .try_idle = tusb_musb_try_idle, + + .vbus_status = tusb_musb_vbus_status, + .set_vbus = tusb_musb_set_vbus, +}; + +static u64 tusb_dmamask = DMA_BIT_MASK(32); + +static int __init tusb_probe(struct platform_device *pdev) +{ + struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data; + struct platform_device *musb; + struct tusb6010_glue *glue; + + int ret = -ENOMEM; + + glue = kzalloc(sizeof(*glue), GFP_KERNEL); + if (!glue) { + dev_err(&pdev->dev, "failed to allocate glue context\n"); + goto err0; + } + + musb = platform_device_alloc("musb-hdrc", -1); + if (!musb) { + dev_err(&pdev->dev, "failed to allocate musb device\n"); + goto err1; + } + + musb->dev.parent = &pdev->dev; + musb->dev.dma_mask = &tusb_dmamask; + musb->dev.coherent_dma_mask = tusb_dmamask; + + glue->dev = &pdev->dev; + glue->musb = musb; + + pdata->platform_ops = &tusb_ops; + + platform_set_drvdata(pdev, glue); + + ret = platform_device_add_resources(musb, pdev->resource, + pdev->num_resources); + if (ret) { + dev_err(&pdev->dev, "failed to add resources\n"); + goto err2; + } + + ret = platform_device_add_data(musb, pdata, sizeof(*pdata)); + if (ret) { + dev_err(&pdev->dev, "failed to add platform_data\n"); + goto err2; + } + + ret = platform_device_add(musb); + if (ret) { + dev_err(&pdev->dev, "failed to register musb device\n"); + goto err1; + } + + return 0; + +err2: + platform_device_put(musb); + +err1: + kfree(glue); + +err0: + return ret; +} + +static int __exit tusb_remove(struct platform_device *pdev) +{ + struct tusb6010_glue *glue = platform_get_drvdata(pdev); + + platform_device_del(glue->musb); + platform_device_put(glue->musb); + kfree(glue); + + return 0; +} + +static struct platform_driver tusb_driver = { + .remove = __exit_p(tusb_remove), + .driver = { + .name = "musb-tusb", + }, +}; + +MODULE_DESCRIPTION("TUSB6010 MUSB Glue Layer"); +MODULE_AUTHOR("Felipe Balbi <balbi@ti.com>"); +MODULE_LICENSE("GPL v2"); + +static int __init tusb_init(void) +{ + return platform_driver_probe(&tusb_driver, tusb_probe); +} +subsys_initcall(tusb_init); + +static void __exit tusb_exit(void) +{ + platform_driver_unregister(&tusb_driver); +} +module_exit(tusb_exit); diff --git a/drivers/usb/musb/ux500.c b/drivers/usb/musb/ux500.c new file mode 100644 index 000000000000..d6384e4aeef9 --- /dev/null +++ b/drivers/usb/musb/ux500.c @@ -0,0 +1,216 @@ +/* + * Copyright (C) 2010 ST-Ericsson AB + * Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com> + * + * Based on omap2430.c + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/clk.h> +#include <linux/io.h> +#include <linux/platform_device.h> + +#include "musb_core.h" + +struct ux500_glue { + struct device *dev; + struct platform_device *musb; + struct clk *clk; +}; +#define glue_to_musb(g) platform_get_drvdata(g->musb) + +static int ux500_musb_init(struct musb *musb) +{ + musb->xceiv = otg_get_transceiver(); + if (!musb->xceiv) { + pr_err("HS USB OTG: no transceiver configured\n"); + return -ENODEV; + } + + return 0; +} + +static int ux500_musb_exit(struct musb *musb) +{ + otg_put_transceiver(musb->xceiv); + + return 0; +} + +static const struct musb_platform_ops ux500_ops = { + .init = ux500_musb_init, + .exit = ux500_musb_exit, +}; + +static int __init ux500_probe(struct platform_device *pdev) +{ + struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data; + struct platform_device *musb; + struct ux500_glue *glue; + struct clk *clk; + + int ret = -ENOMEM; + + glue = kzalloc(sizeof(*glue), GFP_KERNEL); + if (!glue) { + dev_err(&pdev->dev, "failed to allocate glue context\n"); + goto err0; + } + + musb = platform_device_alloc("musb-hdrc", -1); + if (!musb) { + dev_err(&pdev->dev, "failed to allocate musb device\n"); + goto err1; + } + + clk = clk_get(&pdev->dev, "usb"); + if (IS_ERR(clk)) { + dev_err(&pdev->dev, "failed to get clock\n"); + ret = PTR_ERR(clk); + goto err2; + } + + ret = clk_enable(clk); + if (ret) { + dev_err(&pdev->dev, "failed to enable clock\n"); + goto err3; + } + + musb->dev.parent = &pdev->dev; + + glue->dev = &pdev->dev; + glue->musb = musb; + glue->clk = clk; + + pdata->platform_ops = &ux500_ops; + + platform_set_drvdata(pdev, glue); + + ret = platform_device_add_resources(musb, pdev->resource, + pdev->num_resources); + if (ret) { + dev_err(&pdev->dev, "failed to add resources\n"); + goto err4; + } + + ret = platform_device_add_data(musb, pdata, sizeof(*pdata)); + if (ret) { + dev_err(&pdev->dev, "failed to add platform_data\n"); + goto err4; + } + + ret = platform_device_add(musb); + if (ret) { + dev_err(&pdev->dev, "failed to register musb device\n"); + goto err4; + } + + return 0; + +err4: + clk_disable(clk); + +err3: + clk_put(clk); + +err2: + platform_device_put(musb); + +err1: + kfree(glue); + +err0: + return ret; +} + +static int __exit ux500_remove(struct platform_device *pdev) +{ + struct ux500_glue *glue = platform_get_drvdata(pdev); + + platform_device_del(glue->musb); + platform_device_put(glue->musb); + clk_disable(glue->clk); + clk_put(glue->clk); + kfree(glue); + + return 0; +} + +#ifdef CONFIG_PM +static int ux500_suspend(struct device *dev) +{ + struct ux500_glue *glue = dev_get_drvdata(dev); + struct musb *musb = glue_to_musb(glue); + + otg_set_suspend(musb->xceiv, 1); + clk_disable(glue->clk); + + return 0; +} + +static int ux500_resume(struct device *dev) +{ + struct ux500_glue *glue = dev_get_drvdata(dev); + struct musb *musb = glue_to_musb(glue); + int ret; + + ret = clk_enable(glue->clk); + if (ret) { + dev_err(dev, "failed to enable clock\n"); + return ret; + } + + otg_set_suspend(musb->xceiv, 0); + + return 0; +} + +static const struct dev_pm_ops ux500_pm_ops = { + .suspend = ux500_suspend, + .resume = ux500_resume, +}; + +#define DEV_PM_OPS (&ux500_pm_ops) +#else +#define DEV_PM_OPS NULL +#endif + +static struct platform_driver ux500_driver = { + .remove = __exit_p(ux500_remove), + .driver = { + .name = "musb-ux500", + .pm = DEV_PM_OPS, + }, +}; + +MODULE_DESCRIPTION("UX500 MUSB Glue Layer"); +MODULE_AUTHOR("Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>"); +MODULE_LICENSE("GPL v2"); + +static int __init ux500_init(void) +{ + return platform_driver_probe(&ux500_driver, ux500_probe); +} +subsys_initcall(ux500_init); + +static void __exit ux500_exit(void) +{ + platform_driver_unregister(&ux500_driver); +} +module_exit(ux500_exit); diff --git a/drivers/usb/otg/Kconfig b/drivers/usb/otg/Kconfig index 5ce07528cd0c..9fb875d5f09c 100644 --- a/drivers/usb/otg/Kconfig +++ b/drivers/usb/otg/Kconfig @@ -59,6 +59,18 @@ config TWL4030_USB This transceiver supports high and full speed devices plus, in host mode, low speed. +config TWL6030_USB + tristate "TWL6030 USB Transceiver Driver" + depends on TWL4030_CORE + select USB_OTG_UTILS + help + Enable this to support the USB OTG transceiver on TWL6030 + family chips. This TWL6030 transceiver has the VBUS and ID GND + and OTG SRP events capabilities. For all other transceiver functionality + UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs + are hooked to this driver through platform_data structure. + The definition of internal PHY APIs are in the mach-omap2 layer. + config NOP_USB_XCEIV tristate "NOP USB Transceiver Driver" select USB_OTG_UTILS @@ -81,4 +93,24 @@ config USB_LANGWELL_OTG To compile this driver as a module, choose M here: the module will be called langwell_otg. +config USB_MSM_OTG_72K + tristate "OTG support for Qualcomm on-chip USB controller" + depends on (USB || USB_GADGET) && ARCH_MSM + select USB_OTG_UTILS + help + Enable this to support the USB OTG transceiver on MSM chips. It + handles PHY initialization, clock management, and workarounds + required after resetting the hardware and power management. + This driver is required even for peripheral only or host only + mode configurations. + +config AB8500_USB + tristate "AB8500 USB Transceiver Driver" + depends on AB8500_CORE + select USB_OTG_UTILS + help + Enable this to support the USB OTG transceiver in AB8500 chip. + This transceiver supports high and full speed devices plus, + in host mode, low speed. + endif # USB || OTG diff --git a/drivers/usb/otg/Makefile b/drivers/usb/otg/Makefile index 66f1b83e4fa7..a520e715cfd6 100644 --- a/drivers/usb/otg/Makefile +++ b/drivers/usb/otg/Makefile @@ -12,6 +12,9 @@ obj-$(CONFIG_USB_OTG_UTILS) += otg.o obj-$(CONFIG_USB_GPIO_VBUS) += gpio_vbus.o obj-$(CONFIG_ISP1301_OMAP) += isp1301_omap.o obj-$(CONFIG_TWL4030_USB) += twl4030-usb.o +obj-$(CONFIG_TWL6030_USB) += twl6030-usb.o obj-$(CONFIG_USB_LANGWELL_OTG) += langwell_otg.o obj-$(CONFIG_NOP_USB_XCEIV) += nop-usb-xceiv.o obj-$(CONFIG_USB_ULPI) += ulpi.o +obj-$(CONFIG_USB_MSM_OTG_72K) += msm72k_otg.o +obj-$(CONFIG_AB8500_USB) += ab8500-usb.o diff --git a/drivers/usb/otg/ab8500-usb.c b/drivers/usb/otg/ab8500-usb.c new file mode 100644 index 000000000000..d14736b3107b --- /dev/null +++ b/drivers/usb/otg/ab8500-usb.c @@ -0,0 +1,585 @@ +/* + * drivers/usb/otg/ab8500_usb.c + * + * USB transceiver driver for AB8500 chip + * + * Copyright (C) 2010 ST-Ericsson AB + * Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/usb/otg.h> +#include <linux/slab.h> +#include <linux/notifier.h> +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/mfd/abx500.h> +#include <linux/mfd/ab8500.h> + +#define AB8500_MAIN_WD_CTRL_REG 0x01 +#define AB8500_USB_LINE_STAT_REG 0x80 +#define AB8500_USB_PHY_CTRL_REG 0x8A + +#define AB8500_BIT_OTG_STAT_ID (1 << 0) +#define AB8500_BIT_PHY_CTRL_HOST_EN (1 << 0) +#define AB8500_BIT_PHY_CTRL_DEVICE_EN (1 << 1) +#define AB8500_BIT_WD_CTRL_ENABLE (1 << 0) +#define AB8500_BIT_WD_CTRL_KICK (1 << 1) + +#define AB8500_V1x_LINK_STAT_WAIT (HZ/10) +#define AB8500_WD_KICK_DELAY_US 100 /* usec */ +#define AB8500_WD_V11_DISABLE_DELAY_US 100 /* usec */ +#define AB8500_WD_V10_DISABLE_DELAY_MS 100 /* ms */ + +/* Usb line status register */ +enum ab8500_usb_link_status { + USB_LINK_NOT_CONFIGURED = 0, + USB_LINK_STD_HOST_NC, + USB_LINK_STD_HOST_C_NS, + USB_LINK_STD_HOST_C_S, + USB_LINK_HOST_CHG_NM, + USB_LINK_HOST_CHG_HS, + USB_LINK_HOST_CHG_HS_CHIRP, + USB_LINK_DEDICATED_CHG, + USB_LINK_ACA_RID_A, + USB_LINK_ACA_RID_B, + USB_LINK_ACA_RID_C_NM, + USB_LINK_ACA_RID_C_HS, + USB_LINK_ACA_RID_C_HS_CHIRP, + USB_LINK_HM_IDGND, + USB_LINK_RESERVED, + USB_LINK_NOT_VALID_LINK +}; + +struct ab8500_usb { + struct otg_transceiver otg; + struct device *dev; + int irq_num_id_rise; + int irq_num_id_fall; + int irq_num_vbus_rise; + int irq_num_vbus_fall; + int irq_num_link_status; + unsigned vbus_draw; + struct delayed_work dwork; + struct work_struct phy_dis_work; + unsigned long link_status_wait; + int rev; +}; + +static inline struct ab8500_usb *xceiv_to_ab(struct otg_transceiver *x) +{ + return container_of(x, struct ab8500_usb, otg); +} + +static void ab8500_usb_wd_workaround(struct ab8500_usb *ab) +{ + abx500_set_register_interruptible(ab->dev, + AB8500_SYS_CTRL2_BLOCK, + AB8500_MAIN_WD_CTRL_REG, + AB8500_BIT_WD_CTRL_ENABLE); + + udelay(AB8500_WD_KICK_DELAY_US); + + abx500_set_register_interruptible(ab->dev, + AB8500_SYS_CTRL2_BLOCK, + AB8500_MAIN_WD_CTRL_REG, + (AB8500_BIT_WD_CTRL_ENABLE + | AB8500_BIT_WD_CTRL_KICK)); + + if (ab->rev > 0x10) /* v1.1 v2.0 */ + udelay(AB8500_WD_V11_DISABLE_DELAY_US); + else /* v1.0 */ + msleep(AB8500_WD_V10_DISABLE_DELAY_MS); + + abx500_set_register_interruptible(ab->dev, + AB8500_SYS_CTRL2_BLOCK, + AB8500_MAIN_WD_CTRL_REG, + 0); +} + +static void ab8500_usb_phy_ctrl(struct ab8500_usb *ab, bool sel_host, + bool enable) +{ + u8 ctrl_reg; + abx500_get_register_interruptible(ab->dev, + AB8500_USB, + AB8500_USB_PHY_CTRL_REG, + &ctrl_reg); + if (sel_host) { + if (enable) + ctrl_reg |= AB8500_BIT_PHY_CTRL_HOST_EN; + else + ctrl_reg &= ~AB8500_BIT_PHY_CTRL_HOST_EN; + } else { + if (enable) + ctrl_reg |= AB8500_BIT_PHY_CTRL_DEVICE_EN; + else + ctrl_reg &= ~AB8500_BIT_PHY_CTRL_DEVICE_EN; + } + + abx500_set_register_interruptible(ab->dev, + AB8500_USB, + AB8500_USB_PHY_CTRL_REG, + ctrl_reg); + + /* Needed to enable the phy.*/ + if (enable) + ab8500_usb_wd_workaround(ab); +} + +#define ab8500_usb_host_phy_en(ab) ab8500_usb_phy_ctrl(ab, true, true) +#define ab8500_usb_host_phy_dis(ab) ab8500_usb_phy_ctrl(ab, true, false) +#define ab8500_usb_peri_phy_en(ab) ab8500_usb_phy_ctrl(ab, false, true) +#define ab8500_usb_peri_phy_dis(ab) ab8500_usb_phy_ctrl(ab, false, false) + +static int ab8500_usb_link_status_update(struct ab8500_usb *ab) +{ + u8 reg; + enum ab8500_usb_link_status lsts; + void *v = NULL; + enum usb_xceiv_events event; + + abx500_get_register_interruptible(ab->dev, + AB8500_USB, + AB8500_USB_LINE_STAT_REG, + ®); + + lsts = (reg >> 3) & 0x0F; + + switch (lsts) { + case USB_LINK_NOT_CONFIGURED: + case USB_LINK_RESERVED: + case USB_LINK_NOT_VALID_LINK: + /* TODO: Disable regulators. */ + ab8500_usb_host_phy_dis(ab); + ab8500_usb_peri_phy_dis(ab); + ab->otg.state = OTG_STATE_B_IDLE; + ab->otg.default_a = false; + ab->vbus_draw = 0; + event = USB_EVENT_NONE; + break; + + case USB_LINK_STD_HOST_NC: + case USB_LINK_STD_HOST_C_NS: + case USB_LINK_STD_HOST_C_S: + case USB_LINK_HOST_CHG_NM: + case USB_LINK_HOST_CHG_HS: + case USB_LINK_HOST_CHG_HS_CHIRP: + if (ab->otg.gadget) { + /* TODO: Enable regulators. */ + ab8500_usb_peri_phy_en(ab); + v = ab->otg.gadget; + } + event = USB_EVENT_VBUS; + break; + + case USB_LINK_HM_IDGND: + if (ab->otg.host) { + /* TODO: Enable regulators. */ + ab8500_usb_host_phy_en(ab); + v = ab->otg.host; + } + ab->otg.state = OTG_STATE_A_IDLE; + ab->otg.default_a = true; + event = USB_EVENT_ID; + break; + + case USB_LINK_ACA_RID_A: + case USB_LINK_ACA_RID_B: + /* TODO */ + case USB_LINK_ACA_RID_C_NM: + case USB_LINK_ACA_RID_C_HS: + case USB_LINK_ACA_RID_C_HS_CHIRP: + case USB_LINK_DEDICATED_CHG: + /* TODO: vbus_draw */ + event = USB_EVENT_CHARGER; + break; + } + + blocking_notifier_call_chain(&ab->otg.notifier, event, v); + + return 0; +} + +static void ab8500_usb_delayed_work(struct work_struct *work) +{ + struct ab8500_usb *ab = container_of(work, struct ab8500_usb, + dwork.work); + + ab8500_usb_link_status_update(ab); +} + +static irqreturn_t ab8500_usb_v1x_common_irq(int irq, void *data) +{ + struct ab8500_usb *ab = (struct ab8500_usb *) data; + + /* Wait for link status to become stable. */ + schedule_delayed_work(&ab->dwork, ab->link_status_wait); + + return IRQ_HANDLED; +} + +static irqreturn_t ab8500_usb_v1x_vbus_fall_irq(int irq, void *data) +{ + struct ab8500_usb *ab = (struct ab8500_usb *) data; + + /* Link status will not be updated till phy is disabled. */ + ab8500_usb_peri_phy_dis(ab); + + /* Wait for link status to become stable. */ + schedule_delayed_work(&ab->dwork, ab->link_status_wait); + + return IRQ_HANDLED; +} + +static irqreturn_t ab8500_usb_v20_irq(int irq, void *data) +{ + struct ab8500_usb *ab = (struct ab8500_usb *) data; + + ab8500_usb_link_status_update(ab); + + return IRQ_HANDLED; +} + +static void ab8500_usb_phy_disable_work(struct work_struct *work) +{ + struct ab8500_usb *ab = container_of(work, struct ab8500_usb, + phy_dis_work); + + if (!ab->otg.host) + ab8500_usb_host_phy_dis(ab); + + if (!ab->otg.gadget) + ab8500_usb_peri_phy_dis(ab); +} + +static int ab8500_usb_set_power(struct otg_transceiver *otg, unsigned mA) +{ + struct ab8500_usb *ab; + + if (!otg) + return -ENODEV; + + ab = xceiv_to_ab(otg); + + ab->vbus_draw = mA; + + if (mA) + blocking_notifier_call_chain(&ab->otg.notifier, + USB_EVENT_ENUMERATED, ab->otg.gadget); + return 0; +} + +/* TODO: Implement some way for charging or other drivers to read + * ab->vbus_draw. + */ + +static int ab8500_usb_set_suspend(struct otg_transceiver *x, int suspend) +{ + /* TODO */ + return 0; +} + +static int ab8500_usb_set_peripheral(struct otg_transceiver *otg, + struct usb_gadget *gadget) +{ + struct ab8500_usb *ab; + + if (!otg) + return -ENODEV; + + ab = xceiv_to_ab(otg); + + /* Some drivers call this function in atomic context. + * Do not update ab8500 registers directly till this + * is fixed. + */ + + if (!gadget) { + /* TODO: Disable regulators. */ + ab->otg.gadget = NULL; + schedule_work(&ab->phy_dis_work); + } else { + ab->otg.gadget = gadget; + ab->otg.state = OTG_STATE_B_IDLE; + + /* Phy will not be enabled if cable is already + * plugged-in. Schedule to enable phy. + * Use same delay to avoid any race condition. + */ + schedule_delayed_work(&ab->dwork, ab->link_status_wait); + } + + return 0; +} + +static int ab8500_usb_set_host(struct otg_transceiver *otg, + struct usb_bus *host) +{ + struct ab8500_usb *ab; + + if (!otg) + return -ENODEV; + + ab = xceiv_to_ab(otg); + + /* Some drivers call this function in atomic context. + * Do not update ab8500 registers directly till this + * is fixed. + */ + + if (!host) { + /* TODO: Disable regulators. */ + ab->otg.host = NULL; + schedule_work(&ab->phy_dis_work); + } else { + ab->otg.host = host; + /* Phy will not be enabled if cable is already + * plugged-in. Schedule to enable phy. + * Use same delay to avoid any race condition. + */ + schedule_delayed_work(&ab->dwork, ab->link_status_wait); + } + + return 0; +} + +static void ab8500_usb_irq_free(struct ab8500_usb *ab) +{ + if (ab->rev < 0x20) { + free_irq(ab->irq_num_id_rise, ab); + free_irq(ab->irq_num_id_fall, ab); + free_irq(ab->irq_num_vbus_rise, ab); + free_irq(ab->irq_num_vbus_fall, ab); + } else { + free_irq(ab->irq_num_link_status, ab); + } +} + +static int ab8500_usb_v1x_res_setup(struct platform_device *pdev, + struct ab8500_usb *ab) +{ + int err; + + ab->irq_num_id_rise = platform_get_irq_byname(pdev, "ID_WAKEUP_R"); + if (ab->irq_num_id_rise < 0) { + dev_err(&pdev->dev, "ID rise irq not found\n"); + return ab->irq_num_id_rise; + } + err = request_threaded_irq(ab->irq_num_id_rise, NULL, + ab8500_usb_v1x_common_irq, + IRQF_NO_SUSPEND | IRQF_SHARED, + "usb-id-rise", ab); + if (err < 0) { + dev_err(ab->dev, "request_irq failed for ID rise irq\n"); + goto fail0; + } + + ab->irq_num_id_fall = platform_get_irq_byname(pdev, "ID_WAKEUP_F"); + if (ab->irq_num_id_fall < 0) { + dev_err(&pdev->dev, "ID fall irq not found\n"); + return ab->irq_num_id_fall; + } + err = request_threaded_irq(ab->irq_num_id_fall, NULL, + ab8500_usb_v1x_common_irq, + IRQF_NO_SUSPEND | IRQF_SHARED, + "usb-id-fall", ab); + if (err < 0) { + dev_err(ab->dev, "request_irq failed for ID fall irq\n"); + goto fail1; + } + + ab->irq_num_vbus_rise = platform_get_irq_byname(pdev, "VBUS_DET_R"); + if (ab->irq_num_vbus_rise < 0) { + dev_err(&pdev->dev, "VBUS rise irq not found\n"); + return ab->irq_num_vbus_rise; + } + err = request_threaded_irq(ab->irq_num_vbus_rise, NULL, + ab8500_usb_v1x_common_irq, + IRQF_NO_SUSPEND | IRQF_SHARED, + "usb-vbus-rise", ab); + if (err < 0) { + dev_err(ab->dev, "request_irq failed for Vbus rise irq\n"); + goto fail2; + } + + ab->irq_num_vbus_fall = platform_get_irq_byname(pdev, "VBUS_DET_F"); + if (ab->irq_num_vbus_fall < 0) { + dev_err(&pdev->dev, "VBUS fall irq not found\n"); + return ab->irq_num_vbus_fall; + } + err = request_threaded_irq(ab->irq_num_vbus_fall, NULL, + ab8500_usb_v1x_vbus_fall_irq, + IRQF_NO_SUSPEND | IRQF_SHARED, + "usb-vbus-fall", ab); + if (err < 0) { + dev_err(ab->dev, "request_irq failed for Vbus fall irq\n"); + goto fail3; + } + + return 0; +fail3: + free_irq(ab->irq_num_vbus_rise, ab); +fail2: + free_irq(ab->irq_num_id_fall, ab); +fail1: + free_irq(ab->irq_num_id_rise, ab); +fail0: + return err; +} + +static int ab8500_usb_v2_res_setup(struct platform_device *pdev, + struct ab8500_usb *ab) +{ + int err; + + ab->irq_num_link_status = platform_get_irq_byname(pdev, + "USB_LINK_STATUS"); + if (ab->irq_num_link_status < 0) { + dev_err(&pdev->dev, "Link status irq not found\n"); + return ab->irq_num_link_status; + } + + err = request_threaded_irq(ab->irq_num_link_status, NULL, + ab8500_usb_v20_irq, + IRQF_NO_SUSPEND | IRQF_SHARED, + "usb-link-status", ab); + if (err < 0) { + dev_err(ab->dev, + "request_irq failed for link status irq\n"); + return err; + } + + return 0; +} + +static int __devinit ab8500_usb_probe(struct platform_device *pdev) +{ + struct ab8500_usb *ab; + int err; + int rev; + + rev = abx500_get_chip_id(&pdev->dev); + if (rev < 0) { + dev_err(&pdev->dev, "Chip id read failed\n"); + return rev; + } else if (rev < 0x10) { + dev_err(&pdev->dev, "Unsupported AB8500 chip\n"); + return -ENODEV; + } + + ab = kzalloc(sizeof *ab, GFP_KERNEL); + if (!ab) + return -ENOMEM; + + ab->dev = &pdev->dev; + ab->rev = rev; + ab->otg.dev = ab->dev; + ab->otg.label = "ab8500"; + ab->otg.state = OTG_STATE_UNDEFINED; + ab->otg.set_host = ab8500_usb_set_host; + ab->otg.set_peripheral = ab8500_usb_set_peripheral; + ab->otg.set_suspend = ab8500_usb_set_suspend; + ab->otg.set_power = ab8500_usb_set_power; + + platform_set_drvdata(pdev, ab); + + BLOCKING_INIT_NOTIFIER_HEAD(&ab->otg.notifier); + + /* v1: Wait for link status to become stable. + * all: Updates form set_host and set_peripheral as they are atomic. + */ + INIT_DELAYED_WORK(&ab->dwork, ab8500_usb_delayed_work); + + /* all: Disable phy when called from set_host and set_peripheral */ + INIT_WORK(&ab->phy_dis_work, ab8500_usb_phy_disable_work); + + if (ab->rev < 0x20) { + err = ab8500_usb_v1x_res_setup(pdev, ab); + ab->link_status_wait = AB8500_V1x_LINK_STAT_WAIT; + } else { + err = ab8500_usb_v2_res_setup(pdev, ab); + } + + if (err < 0) + goto fail0; + + err = otg_set_transceiver(&ab->otg); + if (err) { + dev_err(&pdev->dev, "Can't register transceiver\n"); + goto fail1; + } + + dev_info(&pdev->dev, "AB8500 usb driver initialized\n"); + + return 0; +fail1: + ab8500_usb_irq_free(ab); +fail0: + kfree(ab); + return err; +} + +static int __devexit ab8500_usb_remove(struct platform_device *pdev) +{ + struct ab8500_usb *ab = platform_get_drvdata(pdev); + + ab8500_usb_irq_free(ab); + + cancel_delayed_work_sync(&ab->dwork); + + cancel_work_sync(&ab->phy_dis_work); + + otg_set_transceiver(NULL); + + ab8500_usb_host_phy_dis(ab); + ab8500_usb_peri_phy_dis(ab); + + platform_set_drvdata(pdev, NULL); + + kfree(ab); + + return 0; +} + +static struct platform_driver ab8500_usb_driver = { + .probe = ab8500_usb_probe, + .remove = __devexit_p(ab8500_usb_remove), + .driver = { + .name = "ab8500-usb", + .owner = THIS_MODULE, + }, +}; + +static int __init ab8500_usb_init(void) +{ + return platform_driver_register(&ab8500_usb_driver); +} +subsys_initcall(ab8500_usb_init); + +static void __exit ab8500_usb_exit(void) +{ + platform_driver_unregister(&ab8500_usb_driver); +} +module_exit(ab8500_usb_exit); + +MODULE_ALIAS("platform:ab8500_usb"); +MODULE_AUTHOR("ST-Ericsson AB"); +MODULE_DESCRIPTION("AB8500 usb transceiver driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/usb/otg/msm72k_otg.c b/drivers/usb/otg/msm72k_otg.c new file mode 100644 index 000000000000..1cd52edcd0c2 --- /dev/null +++ b/drivers/usb/otg/msm72k_otg.c @@ -0,0 +1,1125 @@ +/* Copyright (c) 2009-2010, Code Aurora Forum. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA + * 02110-1301, USA. + * + */ + +#include <linux/module.h> +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/clk.h> +#include <linux/slab.h> +#include <linux/interrupt.h> +#include <linux/err.h> +#include <linux/delay.h> +#include <linux/io.h> +#include <linux/ioport.h> +#include <linux/uaccess.h> +#include <linux/debugfs.h> +#include <linux/seq_file.h> +#include <linux/pm_runtime.h> + +#include <linux/usb.h> +#include <linux/usb/otg.h> +#include <linux/usb/ulpi.h> +#include <linux/usb/gadget.h> +#include <linux/usb/hcd.h> +#include <linux/usb/msm_hsusb.h> +#include <linux/usb/msm_hsusb_hw.h> + +#include <mach/clk.h> + +#define MSM_USB_BASE (motg->regs) +#define DRIVER_NAME "msm_otg" + +#define ULPI_IO_TIMEOUT_USEC (10 * 1000) +static int ulpi_read(struct otg_transceiver *otg, u32 reg) +{ + struct msm_otg *motg = container_of(otg, struct msm_otg, otg); + int cnt = 0; + + /* initiate read operation */ + writel(ULPI_RUN | ULPI_READ | ULPI_ADDR(reg), + USB_ULPI_VIEWPORT); + + /* wait for completion */ + while (cnt < ULPI_IO_TIMEOUT_USEC) { + if (!(readl(USB_ULPI_VIEWPORT) & ULPI_RUN)) + break; + udelay(1); + cnt++; + } + + if (cnt >= ULPI_IO_TIMEOUT_USEC) { + dev_err(otg->dev, "ulpi_read: timeout %08x\n", + readl(USB_ULPI_VIEWPORT)); + return -ETIMEDOUT; + } + return ULPI_DATA_READ(readl(USB_ULPI_VIEWPORT)); +} + +static int ulpi_write(struct otg_transceiver *otg, u32 val, u32 reg) +{ + struct msm_otg *motg = container_of(otg, struct msm_otg, otg); + int cnt = 0; + + /* initiate write operation */ + writel(ULPI_RUN | ULPI_WRITE | + ULPI_ADDR(reg) | ULPI_DATA(val), + USB_ULPI_VIEWPORT); + + /* wait for completion */ + while (cnt < ULPI_IO_TIMEOUT_USEC) { + if (!(readl(USB_ULPI_VIEWPORT) & ULPI_RUN)) + break; + udelay(1); + cnt++; + } + + if (cnt >= ULPI_IO_TIMEOUT_USEC) { + dev_err(otg->dev, "ulpi_write: timeout\n"); + return -ETIMEDOUT; + } + return 0; +} + +static struct otg_io_access_ops msm_otg_io_ops = { + .read = ulpi_read, + .write = ulpi_write, +}; + +static void ulpi_init(struct msm_otg *motg) +{ + struct msm_otg_platform_data *pdata = motg->pdata; + int *seq = pdata->phy_init_seq; + + if (!seq) + return; + + while (seq[0] >= 0) { + dev_vdbg(motg->otg.dev, "ulpi: write 0x%02x to 0x%02x\n", + seq[0], seq[1]); + ulpi_write(&motg->otg, seq[0], seq[1]); + seq += 2; + } +} + +static int msm_otg_link_clk_reset(struct msm_otg *motg, bool assert) +{ + int ret; + + if (assert) { + ret = clk_reset(motg->clk, CLK_RESET_ASSERT); + if (ret) + dev_err(motg->otg.dev, "usb hs_clk assert failed\n"); + } else { + ret = clk_reset(motg->clk, CLK_RESET_DEASSERT); + if (ret) + dev_err(motg->otg.dev, "usb hs_clk deassert failed\n"); + } + return ret; +} + +static int msm_otg_phy_clk_reset(struct msm_otg *motg) +{ + int ret; + + ret = clk_reset(motg->phy_reset_clk, CLK_RESET_ASSERT); + if (ret) { + dev_err(motg->otg.dev, "usb phy clk assert failed\n"); + return ret; + } + usleep_range(10000, 12000); + ret = clk_reset(motg->phy_reset_clk, CLK_RESET_DEASSERT); + if (ret) + dev_err(motg->otg.dev, "usb phy clk deassert failed\n"); + return ret; +} + +static int msm_otg_phy_reset(struct msm_otg *motg) +{ + u32 val; + int ret; + int retries; + + ret = msm_otg_link_clk_reset(motg, 1); + if (ret) + return ret; + ret = msm_otg_phy_clk_reset(motg); + if (ret) + return ret; + ret = msm_otg_link_clk_reset(motg, 0); + if (ret) + return ret; + + val = readl(USB_PORTSC) & ~PORTSC_PTS_MASK; + writel(val | PORTSC_PTS_ULPI, USB_PORTSC); + + for (retries = 3; retries > 0; retries--) { + ret = ulpi_write(&motg->otg, ULPI_FUNC_CTRL_SUSPENDM, + ULPI_CLR(ULPI_FUNC_CTRL)); + if (!ret) + break; + ret = msm_otg_phy_clk_reset(motg); + if (ret) + return ret; + } + if (!retries) + return -ETIMEDOUT; + + /* This reset calibrates the phy, if the above write succeeded */ + ret = msm_otg_phy_clk_reset(motg); + if (ret) + return ret; + + for (retries = 3; retries > 0; retries--) { + ret = ulpi_read(&motg->otg, ULPI_DEBUG); + if (ret != -ETIMEDOUT) + break; + ret = msm_otg_phy_clk_reset(motg); + if (ret) + return ret; + } + if (!retries) + return -ETIMEDOUT; + + dev_info(motg->otg.dev, "phy_reset: success\n"); + return 0; +} + +#define LINK_RESET_TIMEOUT_USEC (250 * 1000) +static int msm_otg_reset(struct otg_transceiver *otg) +{ + struct msm_otg *motg = container_of(otg, struct msm_otg, otg); + struct msm_otg_platform_data *pdata = motg->pdata; + int cnt = 0; + int ret; + u32 val = 0; + u32 ulpi_val = 0; + + ret = msm_otg_phy_reset(motg); + if (ret) { + dev_err(otg->dev, "phy_reset failed\n"); + return ret; + } + + ulpi_init(motg); + + writel(USBCMD_RESET, USB_USBCMD); + while (cnt < LINK_RESET_TIMEOUT_USEC) { + if (!(readl(USB_USBCMD) & USBCMD_RESET)) + break; + udelay(1); + cnt++; + } + if (cnt >= LINK_RESET_TIMEOUT_USEC) + return -ETIMEDOUT; + + /* select ULPI phy */ + writel(0x80000000, USB_PORTSC); + + msleep(100); + + writel(0x0, USB_AHBBURST); + writel(0x00, USB_AHBMODE); + + if (pdata->otg_control == OTG_PHY_CONTROL) { + val = readl(USB_OTGSC); + if (pdata->mode == USB_OTG) { + ulpi_val = ULPI_INT_IDGRD | ULPI_INT_SESS_VALID; + val |= OTGSC_IDIE | OTGSC_BSVIE; + } else if (pdata->mode == USB_PERIPHERAL) { + ulpi_val = ULPI_INT_SESS_VALID; + val |= OTGSC_BSVIE; + } + writel(val, USB_OTGSC); + ulpi_write(otg, ulpi_val, ULPI_USB_INT_EN_RISE); + ulpi_write(otg, ulpi_val, ULPI_USB_INT_EN_FALL); + } + + return 0; +} + +#define PHY_SUSPEND_TIMEOUT_USEC (500 * 1000) +static int msm_otg_suspend(struct msm_otg *motg) +{ + struct otg_transceiver *otg = &motg->otg; + struct usb_bus *bus = otg->host; + struct msm_otg_platform_data *pdata = motg->pdata; + int cnt = 0; + + if (atomic_read(&motg->in_lpm)) + return 0; + + disable_irq(motg->irq); + /* + * Interrupt Latch Register auto-clear feature is not present + * in all PHY versions. Latch register is clear on read type. + * Clear latch register to avoid spurious wakeup from + * low power mode (LPM). + */ + ulpi_read(otg, 0x14); + + /* + * PHY comparators are disabled when PHY enters into low power + * mode (LPM). Keep PHY comparators ON in LPM only when we expect + * VBUS/Id notifications from USB PHY. Otherwise turn off USB + * PHY comparators. This save significant amount of power. + */ + if (pdata->otg_control == OTG_PHY_CONTROL) + ulpi_write(otg, 0x01, 0x30); + + /* + * PLL is not turned off when PHY enters into low power mode (LPM). + * Disable PLL for maximum power savings. + */ + ulpi_write(otg, 0x08, 0x09); + + /* + * PHY may take some time or even fail to enter into low power + * mode (LPM). Hence poll for 500 msec and reset the PHY and link + * in failure case. + */ + writel(readl(USB_PORTSC) | PORTSC_PHCD, USB_PORTSC); + while (cnt < PHY_SUSPEND_TIMEOUT_USEC) { + if (readl(USB_PORTSC) & PORTSC_PHCD) + break; + udelay(1); + cnt++; + } + + if (cnt >= PHY_SUSPEND_TIMEOUT_USEC) { + dev_err(otg->dev, "Unable to suspend PHY\n"); + msm_otg_reset(otg); + enable_irq(motg->irq); + return -ETIMEDOUT; + } + + /* + * PHY has capability to generate interrupt asynchronously in low + * power mode (LPM). This interrupt is level triggered. So USB IRQ + * line must be disabled till async interrupt enable bit is cleared + * in USBCMD register. Assert STP (ULPI interface STOP signal) to + * block data communication from PHY. + */ + writel(readl(USB_USBCMD) | ASYNC_INTR_CTRL | ULPI_STP_CTRL, USB_USBCMD); + + clk_disable(motg->pclk); + clk_disable(motg->clk); + if (motg->core_clk) + clk_disable(motg->core_clk); + + if (device_may_wakeup(otg->dev)) + enable_irq_wake(motg->irq); + if (bus) + clear_bit(HCD_FLAG_HW_ACCESSIBLE, &(bus_to_hcd(bus))->flags); + + atomic_set(&motg->in_lpm, 1); + enable_irq(motg->irq); + + dev_info(otg->dev, "USB in low power mode\n"); + + return 0; +} + +#define PHY_RESUME_TIMEOUT_USEC (100 * 1000) +static int msm_otg_resume(struct msm_otg *motg) +{ + struct otg_transceiver *otg = &motg->otg; + struct usb_bus *bus = otg->host; + int cnt = 0; + unsigned temp; + + if (!atomic_read(&motg->in_lpm)) + return 0; + + clk_enable(motg->pclk); + clk_enable(motg->clk); + if (motg->core_clk) + clk_enable(motg->core_clk); + + temp = readl(USB_USBCMD); + temp &= ~ASYNC_INTR_CTRL; + temp &= ~ULPI_STP_CTRL; + writel(temp, USB_USBCMD); + + /* + * PHY comes out of low power mode (LPM) in case of wakeup + * from asynchronous interrupt. + */ + if (!(readl(USB_PORTSC) & PORTSC_PHCD)) + goto skip_phy_resume; + + writel(readl(USB_PORTSC) & ~PORTSC_PHCD, USB_PORTSC); + while (cnt < PHY_RESUME_TIMEOUT_USEC) { + if (!(readl(USB_PORTSC) & PORTSC_PHCD)) + break; + udelay(1); + cnt++; + } + + if (cnt >= PHY_RESUME_TIMEOUT_USEC) { + /* + * This is a fatal error. Reset the link and + * PHY. USB state can not be restored. Re-insertion + * of USB cable is the only way to get USB working. + */ + dev_err(otg->dev, "Unable to resume USB." + "Re-plugin the cable\n"); + msm_otg_reset(otg); + } + +skip_phy_resume: + if (device_may_wakeup(otg->dev)) + disable_irq_wake(motg->irq); + if (bus) + set_bit(HCD_FLAG_HW_ACCESSIBLE, &(bus_to_hcd(bus))->flags); + + if (motg->async_int) { + motg->async_int = 0; + pm_runtime_put(otg->dev); + enable_irq(motg->irq); + } + + atomic_set(&motg->in_lpm, 0); + + dev_info(otg->dev, "USB exited from low power mode\n"); + + return 0; +} + +static void msm_otg_start_host(struct otg_transceiver *otg, int on) +{ + struct msm_otg *motg = container_of(otg, struct msm_otg, otg); + struct msm_otg_platform_data *pdata = motg->pdata; + struct usb_hcd *hcd; + + if (!otg->host) + return; + + hcd = bus_to_hcd(otg->host); + + if (on) { + dev_dbg(otg->dev, "host on\n"); + + if (pdata->vbus_power) + pdata->vbus_power(1); + /* + * Some boards have a switch cotrolled by gpio + * to enable/disable internal HUB. Enable internal + * HUB before kicking the host. + */ + if (pdata->setup_gpio) + pdata->setup_gpio(OTG_STATE_A_HOST); +#ifdef CONFIG_USB + usb_add_hcd(hcd, hcd->irq, IRQF_SHARED); +#endif + } else { + dev_dbg(otg->dev, "host off\n"); + +#ifdef CONFIG_USB + usb_remove_hcd(hcd); +#endif + if (pdata->setup_gpio) + pdata->setup_gpio(OTG_STATE_UNDEFINED); + if (pdata->vbus_power) + pdata->vbus_power(0); + } +} + +static int msm_otg_set_host(struct otg_transceiver *otg, struct usb_bus *host) +{ + struct msm_otg *motg = container_of(otg, struct msm_otg, otg); + struct usb_hcd *hcd; + + /* + * Fail host registration if this board can support + * only peripheral configuration. + */ + if (motg->pdata->mode == USB_PERIPHERAL) { + dev_info(otg->dev, "Host mode is not supported\n"); + return -ENODEV; + } + + if (!host) { + if (otg->state == OTG_STATE_A_HOST) { + pm_runtime_get_sync(otg->dev); + msm_otg_start_host(otg, 0); + otg->host = NULL; + otg->state = OTG_STATE_UNDEFINED; + schedule_work(&motg->sm_work); + } else { + otg->host = NULL; + } + + return 0; + } + + hcd = bus_to_hcd(host); + hcd->power_budget = motg->pdata->power_budget; + + otg->host = host; + dev_dbg(otg->dev, "host driver registered w/ tranceiver\n"); + + /* + * Kick the state machine work, if peripheral is not supported + * or peripheral is already registered with us. + */ + if (motg->pdata->mode == USB_HOST || otg->gadget) { + pm_runtime_get_sync(otg->dev); + schedule_work(&motg->sm_work); + } + + return 0; +} + +static void msm_otg_start_peripheral(struct otg_transceiver *otg, int on) +{ + struct msm_otg *motg = container_of(otg, struct msm_otg, otg); + struct msm_otg_platform_data *pdata = motg->pdata; + + if (!otg->gadget) + return; + + if (on) { + dev_dbg(otg->dev, "gadget on\n"); + /* + * Some boards have a switch cotrolled by gpio + * to enable/disable internal HUB. Disable internal + * HUB before kicking the gadget. + */ + if (pdata->setup_gpio) + pdata->setup_gpio(OTG_STATE_B_PERIPHERAL); + usb_gadget_vbus_connect(otg->gadget); + } else { + dev_dbg(otg->dev, "gadget off\n"); + usb_gadget_vbus_disconnect(otg->gadget); + if (pdata->setup_gpio) + pdata->setup_gpio(OTG_STATE_UNDEFINED); + } + +} + +static int msm_otg_set_peripheral(struct otg_transceiver *otg, + struct usb_gadget *gadget) +{ + struct msm_otg *motg = container_of(otg, struct msm_otg, otg); + + /* + * Fail peripheral registration if this board can support + * only host configuration. + */ + if (motg->pdata->mode == USB_HOST) { + dev_info(otg->dev, "Peripheral mode is not supported\n"); + return -ENODEV; + } + + if (!gadget) { + if (otg->state == OTG_STATE_B_PERIPHERAL) { + pm_runtime_get_sync(otg->dev); + msm_otg_start_peripheral(otg, 0); + otg->gadget = NULL; + otg->state = OTG_STATE_UNDEFINED; + schedule_work(&motg->sm_work); + } else { + otg->gadget = NULL; + } + + return 0; + } + otg->gadget = gadget; + dev_dbg(otg->dev, "peripheral driver registered w/ tranceiver\n"); + + /* + * Kick the state machine work, if host is not supported + * or host is already registered with us. + */ + if (motg->pdata->mode == USB_PERIPHERAL || otg->host) { + pm_runtime_get_sync(otg->dev); + schedule_work(&motg->sm_work); + } + + return 0; +} + +/* + * We support OTG, Peripheral only and Host only configurations. In case + * of OTG, mode switch (host-->peripheral/peripheral-->host) can happen + * via Id pin status or user request (debugfs). Id/BSV interrupts are not + * enabled when switch is controlled by user and default mode is supplied + * by board file, which can be changed by userspace later. + */ +static void msm_otg_init_sm(struct msm_otg *motg) +{ + struct msm_otg_platform_data *pdata = motg->pdata; + u32 otgsc = readl(USB_OTGSC); + + switch (pdata->mode) { + case USB_OTG: + if (pdata->otg_control == OTG_PHY_CONTROL) { + if (otgsc & OTGSC_ID) + set_bit(ID, &motg->inputs); + else + clear_bit(ID, &motg->inputs); + + if (otgsc & OTGSC_BSV) + set_bit(B_SESS_VLD, &motg->inputs); + else + clear_bit(B_SESS_VLD, &motg->inputs); + } else if (pdata->otg_control == OTG_USER_CONTROL) { + if (pdata->default_mode == USB_HOST) { + clear_bit(ID, &motg->inputs); + } else if (pdata->default_mode == USB_PERIPHERAL) { + set_bit(ID, &motg->inputs); + set_bit(B_SESS_VLD, &motg->inputs); + } else { + set_bit(ID, &motg->inputs); + clear_bit(B_SESS_VLD, &motg->inputs); + } + } + break; + case USB_HOST: + clear_bit(ID, &motg->inputs); + break; + case USB_PERIPHERAL: + set_bit(ID, &motg->inputs); + if (otgsc & OTGSC_BSV) + set_bit(B_SESS_VLD, &motg->inputs); + else + clear_bit(B_SESS_VLD, &motg->inputs); + break; + default: + break; + } +} + +static void msm_otg_sm_work(struct work_struct *w) +{ + struct msm_otg *motg = container_of(w, struct msm_otg, sm_work); + struct otg_transceiver *otg = &motg->otg; + + switch (otg->state) { + case OTG_STATE_UNDEFINED: + dev_dbg(otg->dev, "OTG_STATE_UNDEFINED state\n"); + msm_otg_reset(otg); + msm_otg_init_sm(motg); + otg->state = OTG_STATE_B_IDLE; + /* FALL THROUGH */ + case OTG_STATE_B_IDLE: + dev_dbg(otg->dev, "OTG_STATE_B_IDLE state\n"); + if (!test_bit(ID, &motg->inputs) && otg->host) { + /* disable BSV bit */ + writel(readl(USB_OTGSC) & ~OTGSC_BSVIE, USB_OTGSC); + msm_otg_start_host(otg, 1); + otg->state = OTG_STATE_A_HOST; + } else if (test_bit(B_SESS_VLD, &motg->inputs) && otg->gadget) { + msm_otg_start_peripheral(otg, 1); + otg->state = OTG_STATE_B_PERIPHERAL; + } + pm_runtime_put_sync(otg->dev); + break; + case OTG_STATE_B_PERIPHERAL: + dev_dbg(otg->dev, "OTG_STATE_B_PERIPHERAL state\n"); + if (!test_bit(B_SESS_VLD, &motg->inputs) || + !test_bit(ID, &motg->inputs)) { + msm_otg_start_peripheral(otg, 0); + otg->state = OTG_STATE_B_IDLE; + msm_otg_reset(otg); + schedule_work(w); + } + break; + case OTG_STATE_A_HOST: + dev_dbg(otg->dev, "OTG_STATE_A_HOST state\n"); + if (test_bit(ID, &motg->inputs)) { + msm_otg_start_host(otg, 0); + otg->state = OTG_STATE_B_IDLE; + msm_otg_reset(otg); + schedule_work(w); + } + break; + default: + break; + } +} + +static irqreturn_t msm_otg_irq(int irq, void *data) +{ + struct msm_otg *motg = data; + struct otg_transceiver *otg = &motg->otg; + u32 otgsc = 0; + + if (atomic_read(&motg->in_lpm)) { + disable_irq_nosync(irq); + motg->async_int = 1; + pm_runtime_get(otg->dev); + return IRQ_HANDLED; + } + + otgsc = readl(USB_OTGSC); + if (!(otgsc & (OTGSC_IDIS | OTGSC_BSVIS))) + return IRQ_NONE; + + if ((otgsc & OTGSC_IDIS) && (otgsc & OTGSC_IDIE)) { + if (otgsc & OTGSC_ID) + set_bit(ID, &motg->inputs); + else + clear_bit(ID, &motg->inputs); + dev_dbg(otg->dev, "ID set/clear\n"); + pm_runtime_get_noresume(otg->dev); + } else if ((otgsc & OTGSC_BSVIS) && (otgsc & OTGSC_BSVIE)) { + if (otgsc & OTGSC_BSV) + set_bit(B_SESS_VLD, &motg->inputs); + else + clear_bit(B_SESS_VLD, &motg->inputs); + dev_dbg(otg->dev, "BSV set/clear\n"); + pm_runtime_get_noresume(otg->dev); + } + + writel(otgsc, USB_OTGSC); + schedule_work(&motg->sm_work); + return IRQ_HANDLED; +} + +static int msm_otg_mode_show(struct seq_file *s, void *unused) +{ + struct msm_otg *motg = s->private; + struct otg_transceiver *otg = &motg->otg; + + switch (otg->state) { + case OTG_STATE_A_HOST: + seq_printf(s, "host\n"); + break; + case OTG_STATE_B_PERIPHERAL: + seq_printf(s, "peripheral\n"); + break; + default: + seq_printf(s, "none\n"); + break; + } + + return 0; +} + +static int msm_otg_mode_open(struct inode *inode, struct file *file) +{ + return single_open(file, msm_otg_mode_show, inode->i_private); +} + +static ssize_t msm_otg_mode_write(struct file *file, const char __user *ubuf, + size_t count, loff_t *ppos) +{ + struct msm_otg *motg = file->private_data; + char buf[16]; + struct otg_transceiver *otg = &motg->otg; + int status = count; + enum usb_mode_type req_mode; + + memset(buf, 0x00, sizeof(buf)); + + if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count))) { + status = -EFAULT; + goto out; + } + + if (!strncmp(buf, "host", 4)) { + req_mode = USB_HOST; + } else if (!strncmp(buf, "peripheral", 10)) { + req_mode = USB_PERIPHERAL; + } else if (!strncmp(buf, "none", 4)) { + req_mode = USB_NONE; + } else { + status = -EINVAL; + goto out; + } + + switch (req_mode) { + case USB_NONE: + switch (otg->state) { + case OTG_STATE_A_HOST: + case OTG_STATE_B_PERIPHERAL: + set_bit(ID, &motg->inputs); + clear_bit(B_SESS_VLD, &motg->inputs); + break; + default: + goto out; + } + break; + case USB_PERIPHERAL: + switch (otg->state) { + case OTG_STATE_B_IDLE: + case OTG_STATE_A_HOST: + set_bit(ID, &motg->inputs); + set_bit(B_SESS_VLD, &motg->inputs); + break; + default: + goto out; + } + break; + case USB_HOST: + switch (otg->state) { + case OTG_STATE_B_IDLE: + case OTG_STATE_B_PERIPHERAL: + clear_bit(ID, &motg->inputs); + break; + default: + goto out; + } + break; + default: + goto out; + } + + pm_runtime_get_sync(otg->dev); + schedule_work(&motg->sm_work); +out: + return status; +} + +const struct file_operations msm_otg_mode_fops = { + .open = msm_otg_mode_open, + .read = seq_read, + .write = msm_otg_mode_write, + .llseek = seq_lseek, + .release = single_release, +}; + +static struct dentry *msm_otg_dbg_root; +static struct dentry *msm_otg_dbg_mode; + +static int msm_otg_debugfs_init(struct msm_otg *motg) +{ + msm_otg_dbg_root = debugfs_create_dir("msm_otg", NULL); + + if (!msm_otg_dbg_root || IS_ERR(msm_otg_dbg_root)) + return -ENODEV; + + msm_otg_dbg_mode = debugfs_create_file("mode", S_IRUGO | S_IWUSR, + msm_otg_dbg_root, motg, &msm_otg_mode_fops); + if (!msm_otg_dbg_mode) { + debugfs_remove(msm_otg_dbg_root); + msm_otg_dbg_root = NULL; + return -ENODEV; + } + + return 0; +} + +static void msm_otg_debugfs_cleanup(void) +{ + debugfs_remove(msm_otg_dbg_mode); + debugfs_remove(msm_otg_dbg_root); +} + +static int __init msm_otg_probe(struct platform_device *pdev) +{ + int ret = 0; + struct resource *res; + struct msm_otg *motg; + struct otg_transceiver *otg; + + dev_info(&pdev->dev, "msm_otg probe\n"); + if (!pdev->dev.platform_data) { + dev_err(&pdev->dev, "No platform data given. Bailing out\n"); + return -ENODEV; + } + + motg = kzalloc(sizeof(struct msm_otg), GFP_KERNEL); + if (!motg) { + dev_err(&pdev->dev, "unable to allocate msm_otg\n"); + return -ENOMEM; + } + + motg->pdata = pdev->dev.platform_data; + otg = &motg->otg; + otg->dev = &pdev->dev; + + motg->phy_reset_clk = clk_get(&pdev->dev, "usb_phy_clk"); + if (IS_ERR(motg->phy_reset_clk)) { + dev_err(&pdev->dev, "failed to get usb_phy_clk\n"); + ret = PTR_ERR(motg->phy_reset_clk); + goto free_motg; + } + + motg->clk = clk_get(&pdev->dev, "usb_hs_clk"); + if (IS_ERR(motg->clk)) { + dev_err(&pdev->dev, "failed to get usb_hs_clk\n"); + ret = PTR_ERR(motg->clk); + goto put_phy_reset_clk; + } + + motg->pclk = clk_get(&pdev->dev, "usb_hs_pclk"); + if (IS_ERR(motg->pclk)) { + dev_err(&pdev->dev, "failed to get usb_hs_pclk\n"); + ret = PTR_ERR(motg->pclk); + goto put_clk; + } + + /* + * USB core clock is not present on all MSM chips. This + * clock is introduced to remove the dependency on AXI + * bus frequency. + */ + motg->core_clk = clk_get(&pdev->dev, "usb_hs_core_clk"); + if (IS_ERR(motg->core_clk)) + motg->core_clk = NULL; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "failed to get platform resource mem\n"); + ret = -ENODEV; + goto put_core_clk; + } + + motg->regs = ioremap(res->start, resource_size(res)); + if (!motg->regs) { + dev_err(&pdev->dev, "ioremap failed\n"); + ret = -ENOMEM; + goto put_core_clk; + } + dev_info(&pdev->dev, "OTG regs = %p\n", motg->regs); + + motg->irq = platform_get_irq(pdev, 0); + if (!motg->irq) { + dev_err(&pdev->dev, "platform_get_irq failed\n"); + ret = -ENODEV; + goto free_regs; + } + + clk_enable(motg->clk); + clk_enable(motg->pclk); + if (motg->core_clk) + clk_enable(motg->core_clk); + + writel(0, USB_USBINTR); + writel(0, USB_OTGSC); + + INIT_WORK(&motg->sm_work, msm_otg_sm_work); + ret = request_irq(motg->irq, msm_otg_irq, IRQF_SHARED, + "msm_otg", motg); + if (ret) { + dev_err(&pdev->dev, "request irq failed\n"); + goto disable_clks; + } + + otg->init = msm_otg_reset; + otg->set_host = msm_otg_set_host; + otg->set_peripheral = msm_otg_set_peripheral; + + otg->io_ops = &msm_otg_io_ops; + + ret = otg_set_transceiver(&motg->otg); + if (ret) { + dev_err(&pdev->dev, "otg_set_transceiver failed\n"); + goto free_irq; + } + + platform_set_drvdata(pdev, motg); + device_init_wakeup(&pdev->dev, 1); + + if (motg->pdata->mode == USB_OTG && + motg->pdata->otg_control == OTG_USER_CONTROL) { + ret = msm_otg_debugfs_init(motg); + if (ret) + dev_dbg(&pdev->dev, "mode debugfs file is" + "not available\n"); + } + + pm_runtime_set_active(&pdev->dev); + pm_runtime_enable(&pdev->dev); + + return 0; +free_irq: + free_irq(motg->irq, motg); +disable_clks: + clk_disable(motg->pclk); + clk_disable(motg->clk); +free_regs: + iounmap(motg->regs); +put_core_clk: + if (motg->core_clk) + clk_put(motg->core_clk); + clk_put(motg->pclk); +put_clk: + clk_put(motg->clk); +put_phy_reset_clk: + clk_put(motg->phy_reset_clk); +free_motg: + kfree(motg); + return ret; +} + +static int __devexit msm_otg_remove(struct platform_device *pdev) +{ + struct msm_otg *motg = platform_get_drvdata(pdev); + struct otg_transceiver *otg = &motg->otg; + int cnt = 0; + + if (otg->host || otg->gadget) + return -EBUSY; + + msm_otg_debugfs_cleanup(); + cancel_work_sync(&motg->sm_work); + + msm_otg_resume(motg); + + device_init_wakeup(&pdev->dev, 0); + pm_runtime_disable(&pdev->dev); + + otg_set_transceiver(NULL); + free_irq(motg->irq, motg); + + /* + * Put PHY in low power mode. + */ + ulpi_read(otg, 0x14); + ulpi_write(otg, 0x08, 0x09); + + writel(readl(USB_PORTSC) | PORTSC_PHCD, USB_PORTSC); + while (cnt < PHY_SUSPEND_TIMEOUT_USEC) { + if (readl(USB_PORTSC) & PORTSC_PHCD) + break; + udelay(1); + cnt++; + } + if (cnt >= PHY_SUSPEND_TIMEOUT_USEC) + dev_err(otg->dev, "Unable to suspend PHY\n"); + + clk_disable(motg->pclk); + clk_disable(motg->clk); + if (motg->core_clk) + clk_disable(motg->core_clk); + + iounmap(motg->regs); + pm_runtime_set_suspended(&pdev->dev); + + clk_put(motg->phy_reset_clk); + clk_put(motg->pclk); + clk_put(motg->clk); + if (motg->core_clk) + clk_put(motg->core_clk); + + kfree(motg); + + return 0; +} + +#ifdef CONFIG_PM_RUNTIME +static int msm_otg_runtime_idle(struct device *dev) +{ + struct msm_otg *motg = dev_get_drvdata(dev); + struct otg_transceiver *otg = &motg->otg; + + dev_dbg(dev, "OTG runtime idle\n"); + + /* + * It is observed some times that a spurious interrupt + * comes when PHY is put into LPM immediately after PHY reset. + * This 1 sec delay also prevents entering into LPM immediately + * after asynchronous interrupt. + */ + if (otg->state != OTG_STATE_UNDEFINED) + pm_schedule_suspend(dev, 1000); + + return -EAGAIN; +} + +static int msm_otg_runtime_suspend(struct device *dev) +{ + struct msm_otg *motg = dev_get_drvdata(dev); + + dev_dbg(dev, "OTG runtime suspend\n"); + return msm_otg_suspend(motg); +} + +static int msm_otg_runtime_resume(struct device *dev) +{ + struct msm_otg *motg = dev_get_drvdata(dev); + + dev_dbg(dev, "OTG runtime resume\n"); + return msm_otg_resume(motg); +} +#else +#define msm_otg_runtime_idle NULL +#define msm_otg_runtime_suspend NULL +#define msm_otg_runtime_resume NULL +#endif + +#ifdef CONFIG_PM +static int msm_otg_pm_suspend(struct device *dev) +{ + struct msm_otg *motg = dev_get_drvdata(dev); + + dev_dbg(dev, "OTG PM suspend\n"); + return msm_otg_suspend(motg); +} + +static int msm_otg_pm_resume(struct device *dev) +{ + struct msm_otg *motg = dev_get_drvdata(dev); + int ret; + + dev_dbg(dev, "OTG PM resume\n"); + + ret = msm_otg_resume(motg); + if (ret) + return ret; + + /* + * Runtime PM Documentation recommends bringing the + * device to full powered state upon resume. + */ + pm_runtime_disable(dev); + pm_runtime_set_active(dev); + pm_runtime_enable(dev); + + return 0; +} +#else +#define msm_otg_pm_suspend NULL +#define msm_otg_pm_resume NULL +#endif + +static const struct dev_pm_ops msm_otg_dev_pm_ops = { + .runtime_suspend = msm_otg_runtime_suspend, + .runtime_resume = msm_otg_runtime_resume, + .runtime_idle = msm_otg_runtime_idle, + .suspend = msm_otg_pm_suspend, + .resume = msm_otg_pm_resume, +}; + +static struct platform_driver msm_otg_driver = { + .remove = __devexit_p(msm_otg_remove), + .driver = { + .name = DRIVER_NAME, + .owner = THIS_MODULE, + .pm = &msm_otg_dev_pm_ops, + }, +}; + +static int __init msm_otg_init(void) +{ + return platform_driver_probe(&msm_otg_driver, msm_otg_probe); +} + +static void __exit msm_otg_exit(void) +{ + platform_driver_unregister(&msm_otg_driver); +} + +module_init(msm_otg_init); +module_exit(msm_otg_exit); + +MODULE_LICENSE("GPL v2"); +MODULE_DESCRIPTION("MSM USB transceiver driver"); diff --git a/drivers/usb/otg/twl4030-usb.c b/drivers/usb/otg/twl4030-usb.c index d335f484fcd8..6ca505f333e4 100644 --- a/drivers/usb/otg/twl4030-usb.c +++ b/drivers/usb/otg/twl4030-usb.c @@ -678,7 +678,8 @@ static int __exit twl4030_usb_remove(struct platform_device *pdev) /* disable complete OTG block */ twl4030_usb_clear_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB); - twl4030_phy_power(twl, 0); + if (!twl->asleep) + twl4030_phy_power(twl, 0); regulator_put(twl->usb1v5); regulator_put(twl->usb1v8); regulator_put(twl->usb3v1); diff --git a/drivers/usb/otg/twl6030-usb.c b/drivers/usb/otg/twl6030-usb.c new file mode 100644 index 000000000000..28f770103640 --- /dev/null +++ b/drivers/usb/otg/twl6030-usb.c @@ -0,0 +1,493 @@ +/* + * twl6030_usb - TWL6030 USB transceiver, talking to OMAP OTG driver. + * + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * Author: Hema HK <hemahk@ti.com> + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/usb/otg.h> +#include <linux/i2c/twl.h> +#include <linux/regulator/consumer.h> +#include <linux/err.h> +#include <linux/notifier.h> +#include <linux/slab.h> + +/* usb register definitions */ +#define USB_VENDOR_ID_LSB 0x00 +#define USB_VENDOR_ID_MSB 0x01 +#define USB_PRODUCT_ID_LSB 0x02 +#define USB_PRODUCT_ID_MSB 0x03 +#define USB_VBUS_CTRL_SET 0x04 +#define USB_VBUS_CTRL_CLR 0x05 +#define USB_ID_CTRL_SET 0x06 +#define USB_ID_CTRL_CLR 0x07 +#define USB_VBUS_INT_SRC 0x08 +#define USB_VBUS_INT_LATCH_SET 0x09 +#define USB_VBUS_INT_LATCH_CLR 0x0A +#define USB_VBUS_INT_EN_LO_SET 0x0B +#define USB_VBUS_INT_EN_LO_CLR 0x0C +#define USB_VBUS_INT_EN_HI_SET 0x0D +#define USB_VBUS_INT_EN_HI_CLR 0x0E +#define USB_ID_INT_SRC 0x0F +#define USB_ID_INT_LATCH_SET 0x10 +#define USB_ID_INT_LATCH_CLR 0x11 + +#define USB_ID_INT_EN_LO_SET 0x12 +#define USB_ID_INT_EN_LO_CLR 0x13 +#define USB_ID_INT_EN_HI_SET 0x14 +#define USB_ID_INT_EN_HI_CLR 0x15 +#define USB_OTG_ADP_CTRL 0x16 +#define USB_OTG_ADP_HIGH 0x17 +#define USB_OTG_ADP_LOW 0x18 +#define USB_OTG_ADP_RISE 0x19 +#define USB_OTG_REVISION 0x1A + +/* to be moved to LDO */ +#define TWL6030_MISC2 0xE5 +#define TWL6030_CFG_LDO_PD2 0xF5 +#define TWL6030_BACKUP_REG 0xFA + +#define STS_HW_CONDITIONS 0x21 + +/* In module TWL6030_MODULE_PM_MASTER */ +#define STS_HW_CONDITIONS 0x21 +#define STS_USB_ID BIT(2) + +/* In module TWL6030_MODULE_PM_RECEIVER */ +#define VUSB_CFG_TRANS 0x71 +#define VUSB_CFG_STATE 0x72 +#define VUSB_CFG_VOLTAGE 0x73 + +/* in module TWL6030_MODULE_MAIN_CHARGE */ + +#define CHARGERUSB_CTRL1 0x8 + +#define CONTROLLER_STAT1 0x03 +#define VBUS_DET BIT(2) + +struct twl6030_usb { + struct otg_transceiver otg; + struct device *dev; + + /* for vbus reporting with irqs disabled */ + spinlock_t lock; + + struct regulator *usb3v3; + + int irq1; + int irq2; + u8 linkstat; + u8 asleep; + bool irq_enabled; +}; + +#define xceiv_to_twl(x) container_of((x), struct twl6030_usb, otg); + +/*-------------------------------------------------------------------------*/ + +static inline int twl6030_writeb(struct twl6030_usb *twl, u8 module, + u8 data, u8 address) +{ + int ret = 0; + + ret = twl_i2c_write_u8(module, data, address); + if (ret < 0) + dev_err(twl->dev, + "Write[0x%x] Error %d\n", address, ret); + return ret; +} + +static inline u8 twl6030_readb(struct twl6030_usb *twl, u8 module, u8 address) +{ + u8 data, ret = 0; + + ret = twl_i2c_read_u8(module, &data, address); + if (ret >= 0) + ret = data; + else + dev_err(twl->dev, + "readb[0x%x,0x%x] Error %d\n", + module, address, ret); + return ret; +} + +/*-------------------------------------------------------------------------*/ +static int twl6030_set_phy_clk(struct otg_transceiver *x, int on) +{ + struct twl6030_usb *twl; + struct device *dev; + struct twl4030_usb_data *pdata; + + twl = xceiv_to_twl(x); + dev = twl->dev; + pdata = dev->platform_data; + + pdata->phy_set_clock(twl->dev, on); + + return 0; +} + +static int twl6030_phy_init(struct otg_transceiver *x) +{ + u8 hw_state; + struct twl6030_usb *twl; + struct device *dev; + struct twl4030_usb_data *pdata; + + twl = xceiv_to_twl(x); + dev = twl->dev; + pdata = dev->platform_data; + + regulator_enable(twl->usb3v3); + + hw_state = twl6030_readb(twl, TWL6030_MODULE_ID0, STS_HW_CONDITIONS); + + if (hw_state & STS_USB_ID) + pdata->phy_power(twl->dev, 1, 1); + else + pdata->phy_power(twl->dev, 0, 1); + + return 0; +} + +static void twl6030_phy_shutdown(struct otg_transceiver *x) +{ + struct twl6030_usb *twl; + struct device *dev; + struct twl4030_usb_data *pdata; + + twl = xceiv_to_twl(x); + dev = twl->dev; + pdata = dev->platform_data; + pdata->phy_power(twl->dev, 0, 0); + regulator_disable(twl->usb3v3); +} + +static int twl6030_usb_ldo_init(struct twl6030_usb *twl) +{ + + /* Set to OTG_REV 1.3 and turn on the ID_WAKEUP_COMP */ + twl6030_writeb(twl, TWL6030_MODULE_ID0 , 0x1, TWL6030_BACKUP_REG); + + /* Program CFG_LDO_PD2 register and set VUSB bit */ + twl6030_writeb(twl, TWL6030_MODULE_ID0 , 0x1, TWL6030_CFG_LDO_PD2); + + /* Program MISC2 register and set bit VUSB_IN_VBAT */ + twl6030_writeb(twl, TWL6030_MODULE_ID0 , 0x10, TWL6030_MISC2); + + twl->usb3v3 = regulator_get(twl->dev, "vusb"); + if (IS_ERR(twl->usb3v3)) + return -ENODEV; + + regulator_enable(twl->usb3v3); + + /* Program the VUSB_CFG_TRANS for ACTIVE state. */ + twl6030_writeb(twl, TWL_MODULE_PM_RECEIVER, 0x3F, + VUSB_CFG_TRANS); + + /* Program the VUSB_CFG_STATE register to ON on all groups. */ + twl6030_writeb(twl, TWL_MODULE_PM_RECEIVER, 0xE1, + VUSB_CFG_STATE); + + /* Program the USB_VBUS_CTRL_SET and set VBUS_ACT_COMP bit */ + twl6030_writeb(twl, TWL_MODULE_USB, 0x4, USB_VBUS_CTRL_SET); + + /* + * Program the USB_ID_CTRL_SET register to enable GND drive + * and the ID comparators + */ + twl6030_writeb(twl, TWL_MODULE_USB, 0x14, USB_ID_CTRL_SET); + + return 0; +} + +static ssize_t twl6030_usb_vbus_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct twl6030_usb *twl = dev_get_drvdata(dev); + unsigned long flags; + int ret = -EINVAL; + + spin_lock_irqsave(&twl->lock, flags); + + switch (twl->linkstat) { + case USB_EVENT_VBUS: + ret = snprintf(buf, PAGE_SIZE, "vbus\n"); + break; + case USB_EVENT_ID: + ret = snprintf(buf, PAGE_SIZE, "id\n"); + break; + case USB_EVENT_NONE: + ret = snprintf(buf, PAGE_SIZE, "none\n"); + break; + default: + ret = snprintf(buf, PAGE_SIZE, "UNKNOWN\n"); + } + spin_unlock_irqrestore(&twl->lock, flags); + + return ret; +} +static DEVICE_ATTR(vbus, 0444, twl6030_usb_vbus_show, NULL); + +static irqreturn_t twl6030_usb_irq(int irq, void *_twl) +{ + struct twl6030_usb *twl = _twl; + int status; + u8 vbus_state, hw_state; + + hw_state = twl6030_readb(twl, TWL6030_MODULE_ID0, STS_HW_CONDITIONS); + + vbus_state = twl6030_readb(twl, TWL_MODULE_MAIN_CHARGE, + CONTROLLER_STAT1); + if (!(hw_state & STS_USB_ID)) { + if (vbus_state & VBUS_DET) { + status = USB_EVENT_VBUS; + twl->otg.default_a = false; + twl->otg.state = OTG_STATE_B_IDLE; + } else { + status = USB_EVENT_NONE; + } + if (status >= 0) { + twl->linkstat = status; + blocking_notifier_call_chain(&twl->otg.notifier, + status, twl->otg.gadget); + } + } + sysfs_notify(&twl->dev->kobj, NULL, "vbus"); + + return IRQ_HANDLED; +} + +static irqreturn_t twl6030_usbotg_irq(int irq, void *_twl) +{ + struct twl6030_usb *twl = _twl; + int status = USB_EVENT_NONE; + u8 hw_state; + + hw_state = twl6030_readb(twl, TWL6030_MODULE_ID0, STS_HW_CONDITIONS); + + if (hw_state & STS_USB_ID) { + + twl6030_writeb(twl, TWL_MODULE_USB, USB_ID_INT_EN_HI_CLR, 0x1); + twl6030_writeb(twl, TWL_MODULE_USB, USB_ID_INT_EN_HI_SET, + 0x10); + status = USB_EVENT_ID; + twl->otg.default_a = true; + twl->otg.state = OTG_STATE_A_IDLE; + blocking_notifier_call_chain(&twl->otg.notifier, status, + twl->otg.gadget); + } else { + twl6030_writeb(twl, TWL_MODULE_USB, USB_ID_INT_EN_HI_CLR, + 0x10); + twl6030_writeb(twl, TWL_MODULE_USB, USB_ID_INT_EN_HI_SET, + 0x1); + } + twl6030_writeb(twl, TWL_MODULE_USB, USB_ID_INT_LATCH_CLR, status); + twl->linkstat = status; + + return IRQ_HANDLED; +} + +static int twl6030_set_peripheral(struct otg_transceiver *x, + struct usb_gadget *gadget) +{ + struct twl6030_usb *twl; + + if (!x) + return -ENODEV; + + twl = xceiv_to_twl(x); + twl->otg.gadget = gadget; + if (!gadget) + twl->otg.state = OTG_STATE_UNDEFINED; + + return 0; +} + +static int twl6030_enable_irq(struct otg_transceiver *x) +{ + struct twl6030_usb *twl = xceiv_to_twl(x); + + twl6030_writeb(twl, TWL_MODULE_USB, USB_ID_INT_EN_HI_SET, 0x1); + twl6030_interrupt_unmask(0x05, REG_INT_MSK_LINE_C); + twl6030_interrupt_unmask(0x05, REG_INT_MSK_STS_C); + + twl6030_interrupt_unmask(TWL6030_CHARGER_CTRL_INT_MASK, + REG_INT_MSK_LINE_C); + twl6030_interrupt_unmask(TWL6030_CHARGER_CTRL_INT_MASK, + REG_INT_MSK_STS_C); + twl6030_usb_irq(twl->irq2, twl); + twl6030_usbotg_irq(twl->irq1, twl); + + return 0; +} + +static int twl6030_set_vbus(struct otg_transceiver *x, bool enabled) +{ + struct twl6030_usb *twl = xceiv_to_twl(x); + + /* + * Start driving VBUS. Set OPA_MODE bit in CHARGERUSB_CTRL1 + * register. This enables boost mode. + */ + if (enabled) + twl6030_writeb(twl, TWL_MODULE_MAIN_CHARGE , 0x40, + CHARGERUSB_CTRL1); + else + twl6030_writeb(twl, TWL_MODULE_MAIN_CHARGE , 0x00, + CHARGERUSB_CTRL1); + return 0; +} + +static int twl6030_set_host(struct otg_transceiver *x, struct usb_bus *host) +{ + struct twl6030_usb *twl; + + if (!x) + return -ENODEV; + + twl = xceiv_to_twl(x); + twl->otg.host = host; + if (!host) + twl->otg.state = OTG_STATE_UNDEFINED; + return 0; +} + +static int __devinit twl6030_usb_probe(struct platform_device *pdev) +{ + struct twl6030_usb *twl; + int status, err; + struct twl4030_usb_data *pdata; + struct device *dev = &pdev->dev; + pdata = dev->platform_data; + + twl = kzalloc(sizeof *twl, GFP_KERNEL); + if (!twl) + return -ENOMEM; + + twl->dev = &pdev->dev; + twl->irq1 = platform_get_irq(pdev, 0); + twl->irq2 = platform_get_irq(pdev, 1); + twl->otg.dev = twl->dev; + twl->otg.label = "twl6030"; + twl->otg.set_host = twl6030_set_host; + twl->otg.set_peripheral = twl6030_set_peripheral; + twl->otg.set_vbus = twl6030_set_vbus; + twl->otg.init = twl6030_phy_init; + twl->otg.shutdown = twl6030_phy_shutdown; + + /* init spinlock for workqueue */ + spin_lock_init(&twl->lock); + + err = twl6030_usb_ldo_init(twl); + if (err) { + dev_err(&pdev->dev, "ldo init failed\n"); + kfree(twl); + return err; + } + otg_set_transceiver(&twl->otg); + + platform_set_drvdata(pdev, twl); + if (device_create_file(&pdev->dev, &dev_attr_vbus)) + dev_warn(&pdev->dev, "could not create sysfs file\n"); + + BLOCKING_INIT_NOTIFIER_HEAD(&twl->otg.notifier); + + twl->irq_enabled = true; + status = request_threaded_irq(twl->irq1, NULL, twl6030_usbotg_irq, + IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, + "twl6030_usb", twl); + if (status < 0) { + dev_err(&pdev->dev, "can't get IRQ %d, err %d\n", + twl->irq1, status); + device_remove_file(twl->dev, &dev_attr_vbus); + kfree(twl); + return status; + } + + status = request_threaded_irq(twl->irq2, NULL, twl6030_usb_irq, + IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, + "twl6030_usb", twl); + if (status < 0) { + dev_err(&pdev->dev, "can't get IRQ %d, err %d\n", + twl->irq2, status); + free_irq(twl->irq1, twl); + device_remove_file(twl->dev, &dev_attr_vbus); + kfree(twl); + return status; + } + + pdata->phy_init(dev); + twl6030_enable_irq(&twl->otg); + dev_info(&pdev->dev, "Initialized TWL6030 USB module\n"); + + return 0; +} + +static int __exit twl6030_usb_remove(struct platform_device *pdev) +{ + struct twl6030_usb *twl = platform_get_drvdata(pdev); + + struct twl4030_usb_data *pdata; + struct device *dev = &pdev->dev; + pdata = dev->platform_data; + + twl6030_interrupt_mask(TWL6030_USBOTG_INT_MASK, + REG_INT_MSK_LINE_C); + twl6030_interrupt_mask(TWL6030_USBOTG_INT_MASK, + REG_INT_MSK_STS_C); + free_irq(twl->irq1, twl); + free_irq(twl->irq2, twl); + regulator_put(twl->usb3v3); + pdata->phy_exit(twl->dev); + device_remove_file(twl->dev, &dev_attr_vbus); + kfree(twl); + + return 0; +} + +static struct platform_driver twl6030_usb_driver = { + .probe = twl6030_usb_probe, + .remove = __exit_p(twl6030_usb_remove), + .driver = { + .name = "twl6030_usb", + .owner = THIS_MODULE, + }, +}; + +static int __init twl6030_usb_init(void) +{ + return platform_driver_register(&twl6030_usb_driver); +} +subsys_initcall(twl6030_usb_init); + +static void __exit twl6030_usb_exit(void) +{ + platform_driver_unregister(&twl6030_usb_driver); +} +module_exit(twl6030_usb_exit); + +MODULE_ALIAS("platform:twl6030_usb"); +MODULE_AUTHOR("Hema HK <hemahk@ti.com>"); +MODULE_DESCRIPTION("TWL6030 USB transceiver driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index ef2977d3a613..cdfb1868caef 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -989,6 +989,7 @@ static struct usb_serial_driver option_1port_device = { .set_termios = usb_wwan_set_termios, .tiocmget = usb_wwan_tiocmget, .tiocmset = usb_wwan_tiocmset, + .ioctl = usb_wwan_ioctl, .attach = usb_wwan_startup, .disconnect = usb_wwan_disconnect, .release = usb_wwan_release, diff --git a/drivers/usb/serial/ssu100.c b/drivers/usb/serial/ssu100.c index f5312dd3331b..8359ec798959 100644 --- a/drivers/usb/serial/ssu100.c +++ b/drivers/usb/serial/ssu100.c @@ -79,7 +79,6 @@ struct ssu100_port_private { u8 shadowLSR; u8 shadowMSR; wait_queue_head_t delta_msr_wait; /* Used for TIOCMIWAIT */ - unsigned short max_packet_size; struct async_icount icount; }; @@ -464,36 +463,6 @@ static int ssu100_ioctl(struct tty_struct *tty, struct file *file, return -ENOIOCTLCMD; } -static void ssu100_set_max_packet_size(struct usb_serial_port *port) -{ - struct ssu100_port_private *priv = usb_get_serial_port_data(port); - struct usb_serial *serial = port->serial; - struct usb_device *udev = serial->dev; - - struct usb_interface *interface = serial->interface; - struct usb_endpoint_descriptor *ep_desc = &interface->cur_altsetting->endpoint[1].desc; - - unsigned num_endpoints; - int i; - unsigned long flags; - - num_endpoints = interface->cur_altsetting->desc.bNumEndpoints; - dev_info(&udev->dev, "Number of endpoints %d\n", num_endpoints); - - for (i = 0; i < num_endpoints; i++) { - dev_info(&udev->dev, "Endpoint %d MaxPacketSize %d\n", i+1, - interface->cur_altsetting->endpoint[i].desc.wMaxPacketSize); - ep_desc = &interface->cur_altsetting->endpoint[i].desc; - } - - /* set max packet size based on descriptor */ - spin_lock_irqsave(&priv->status_lock, flags); - priv->max_packet_size = ep_desc->wMaxPacketSize; - spin_unlock_irqrestore(&priv->status_lock, flags); - - dev_info(&udev->dev, "Setting MaxPacketSize %d\n", priv->max_packet_size); -} - static int ssu100_attach(struct usb_serial *serial) { struct ssu100_port_private *priv; @@ -511,7 +480,6 @@ static int ssu100_attach(struct usb_serial *serial) spin_lock_init(&priv->status_lock); init_waitqueue_head(&priv->delta_msr_wait); usb_set_serial_port_data(port, priv); - ssu100_set_max_packet_size(port); return ssu100_initdevice(serial->dev); } @@ -641,13 +609,14 @@ static void ssu100_update_lsr(struct usb_serial_port *port, u8 lsr, } -static int ssu100_process_packet(struct tty_struct *tty, - struct usb_serial_port *port, - struct ssu100_port_private *priv, - char *packet, int len) +static int ssu100_process_packet(struct urb *urb, + struct tty_struct *tty) { - int i; + struct usb_serial_port *port = urb->context; + char *packet = (char *)urb->transfer_buffer; char flag = TTY_NORMAL; + u32 len = urb->actual_length; + int i; char *ch; dbg("%s - port %d", __func__, port->number); @@ -685,12 +654,8 @@ static int ssu100_process_packet(struct tty_struct *tty, static void ssu100_process_read_urb(struct urb *urb) { struct usb_serial_port *port = urb->context; - struct ssu100_port_private *priv = usb_get_serial_port_data(port); - char *data = (char *)urb->transfer_buffer; struct tty_struct *tty; - int count = 0; - int i; - int len; + int count; dbg("%s", __func__); @@ -698,10 +663,7 @@ static void ssu100_process_read_urb(struct urb *urb) if (!tty) return; - for (i = 0; i < urb->actual_length; i += priv->max_packet_size) { - len = min_t(int, urb->actual_length - i, priv->max_packet_size); - count += ssu100_process_packet(tty, port, priv, &data[i], len); - } + count = ssu100_process_packet(urb, tty); if (count) tty_flip_buffer_push(tty); @@ -717,8 +679,6 @@ static struct usb_serial_driver ssu100_device = { .id_table = id_table, .usb_driver = &ssu100_driver, .num_ports = 1, - .bulk_in_size = 256, - .bulk_out_size = 256, .open = ssu100_open, .close = ssu100_close, .attach = ssu100_attach, diff --git a/drivers/usb/serial/usb-wwan.h b/drivers/usb/serial/usb-wwan.h index 2be298a1305b..3ab77c5d9819 100644 --- a/drivers/usb/serial/usb-wwan.h +++ b/drivers/usb/serial/usb-wwan.h @@ -18,6 +18,8 @@ extern void usb_wwan_set_termios(struct tty_struct *tty, extern int usb_wwan_tiocmget(struct tty_struct *tty, struct file *file); extern int usb_wwan_tiocmset(struct tty_struct *tty, struct file *file, unsigned int set, unsigned int clear); +extern int usb_wwan_ioctl(struct tty_struct *tty, struct file *file, + unsigned int cmd, unsigned long arg); extern int usb_wwan_send_setup(struct usb_serial_port *port); extern int usb_wwan_write(struct tty_struct *tty, struct usb_serial_port *port, const unsigned char *buf, int count); diff --git a/drivers/usb/serial/usb_wwan.c b/drivers/usb/serial/usb_wwan.c index fbc946797801..b004b2a485c3 100644 --- a/drivers/usb/serial/usb_wwan.c +++ b/drivers/usb/serial/usb_wwan.c @@ -31,8 +31,10 @@ #include <linux/tty_flip.h> #include <linux/module.h> #include <linux/bitops.h> +#include <linux/uaccess.h> #include <linux/usb.h> #include <linux/usb/serial.h> +#include <linux/serial.h> #include "usb-wwan.h" static int debug; @@ -123,6 +125,83 @@ int usb_wwan_tiocmset(struct tty_struct *tty, struct file *file, } EXPORT_SYMBOL(usb_wwan_tiocmset); +static int get_serial_info(struct usb_serial_port *port, + struct serial_struct __user *retinfo) +{ + struct serial_struct tmp; + + if (!retinfo) + return -EFAULT; + + memset(&tmp, 0, sizeof(tmp)); + tmp.line = port->serial->minor; + tmp.port = port->number; + tmp.baud_base = tty_get_baud_rate(port->port.tty); + tmp.close_delay = port->port.close_delay / 10; + tmp.closing_wait = port->port.closing_wait == ASYNC_CLOSING_WAIT_NONE ? + ASYNC_CLOSING_WAIT_NONE : + port->port.closing_wait / 10; + + if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) + return -EFAULT; + return 0; +} + +static int set_serial_info(struct usb_serial_port *port, + struct serial_struct __user *newinfo) +{ + struct serial_struct new_serial; + unsigned int closing_wait, close_delay; + int retval = 0; + + if (copy_from_user(&new_serial, newinfo, sizeof(new_serial))) + return -EFAULT; + + close_delay = new_serial.close_delay * 10; + closing_wait = new_serial.closing_wait == ASYNC_CLOSING_WAIT_NONE ? + ASYNC_CLOSING_WAIT_NONE : new_serial.closing_wait * 10; + + mutex_lock(&port->port.mutex); + + if (!capable(CAP_SYS_ADMIN)) { + if ((close_delay != port->port.close_delay) || + (closing_wait != port->port.closing_wait)) + retval = -EPERM; + else + retval = -EOPNOTSUPP; + } else { + port->port.close_delay = close_delay; + port->port.closing_wait = closing_wait; + } + + mutex_unlock(&port->port.mutex); + return retval; +} + +int usb_wwan_ioctl(struct tty_struct *tty, struct file *file, + unsigned int cmd, unsigned long arg) +{ + struct usb_serial_port *port = tty->driver_data; + + dbg("%s cmd 0x%04x", __func__, cmd); + + switch (cmd) { + case TIOCGSERIAL: + return get_serial_info(port, + (struct serial_struct __user *) arg); + case TIOCSSERIAL: + return set_serial_info(port, + (struct serial_struct __user *) arg); + default: + break; + } + + dbg("%s arg not supported", __func__); + + return -ENOIOCTLCMD; +} +EXPORT_SYMBOL(usb_wwan_ioctl); + /* Write */ int usb_wwan_write(struct tty_struct *tty, struct usb_serial_port *port, const unsigned char *buf, int count) diff --git a/drivers/usb/storage/uas.c b/drivers/usb/storage/uas.c index 339fac3949df..23f0dd9c36d4 100644 --- a/drivers/usb/storage/uas.c +++ b/drivers/usb/storage/uas.c @@ -49,14 +49,17 @@ struct command_iu { __u8 cdb[16]; /* XXX: Overflow-checking tools may misunderstand */ }; +/* + * Also used for the Read Ready and Write Ready IUs since they have the + * same first four bytes + */ struct sense_iu { __u8 iu_id; __u8 rsvd1; __be16 tag; __be16 status_qual; __u8 status; - __u8 service_response; - __u8 rsvd8[6]; + __u8 rsvd7[7]; __be16 len; __u8 sense[SCSI_SENSE_BUFFERSIZE]; }; @@ -97,8 +100,8 @@ struct uas_dev_info { }; enum { - ALLOC_SENSE_URB = (1 << 0), - SUBMIT_SENSE_URB = (1 << 1), + ALLOC_STATUS_URB = (1 << 0), + SUBMIT_STATUS_URB = (1 << 1), ALLOC_DATA_IN_URB = (1 << 2), SUBMIT_DATA_IN_URB = (1 << 3), ALLOC_DATA_OUT_URB = (1 << 4), @@ -112,7 +115,7 @@ struct uas_cmd_info { unsigned int state; unsigned int stream; struct urb *cmd_urb; - struct urb *sense_urb; + struct urb *status_urb; struct urb *data_in_urb; struct urb *data_out_urb; struct list_head list; @@ -138,7 +141,7 @@ static void uas_do_work(struct work_struct *work) struct scsi_pointer *scp = (void *)cmdinfo; struct scsi_cmnd *cmnd = container_of(scp, struct scsi_cmnd, SCp); - uas_submit_urbs(cmnd, cmnd->device->hostdata, GFP_KERNEL); + uas_submit_urbs(cmnd, cmnd->device->hostdata, GFP_NOIO); } } @@ -204,7 +207,7 @@ static void uas_xfer_data(struct urb *urb, struct scsi_cmnd *cmnd, struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp; int err; - cmdinfo->state = direction | SUBMIT_SENSE_URB; + cmdinfo->state = direction | SUBMIT_STATUS_URB; err = uas_submit_urbs(cmnd, cmnd->device->hostdata, GFP_ATOMIC); if (err) { spin_lock(&uas_work_lock); @@ -294,7 +297,7 @@ static struct urb *uas_alloc_sense_urb(struct uas_dev_info *devinfo, gfp_t gfp, if (!urb) goto out; - iu = kmalloc(sizeof(*iu), gfp); + iu = kzalloc(sizeof(*iu), gfp); if (!iu) goto free; @@ -325,7 +328,7 @@ static struct urb *uas_alloc_cmd_urb(struct uas_dev_info *devinfo, gfp_t gfp, if (len < 0) len = 0; len = ALIGN(len, 4); - iu = kmalloc(sizeof(*iu) + len, gfp); + iu = kzalloc(sizeof(*iu) + len, gfp); if (!iu) goto free; @@ -357,21 +360,21 @@ static int uas_submit_urbs(struct scsi_cmnd *cmnd, { struct uas_cmd_info *cmdinfo = (void *)&cmnd->SCp; - if (cmdinfo->state & ALLOC_SENSE_URB) { - cmdinfo->sense_urb = uas_alloc_sense_urb(devinfo, gfp, cmnd, - cmdinfo->stream); - if (!cmdinfo->sense_urb) + if (cmdinfo->state & ALLOC_STATUS_URB) { + cmdinfo->status_urb = uas_alloc_sense_urb(devinfo, gfp, cmnd, + cmdinfo->stream); + if (!cmdinfo->status_urb) return SCSI_MLQUEUE_DEVICE_BUSY; - cmdinfo->state &= ~ALLOC_SENSE_URB; + cmdinfo->state &= ~ALLOC_STATUS_URB; } - if (cmdinfo->state & SUBMIT_SENSE_URB) { - if (usb_submit_urb(cmdinfo->sense_urb, gfp)) { + if (cmdinfo->state & SUBMIT_STATUS_URB) { + if (usb_submit_urb(cmdinfo->status_urb, gfp)) { scmd_printk(KERN_INFO, cmnd, "sense urb submission failure\n"); return SCSI_MLQUEUE_DEVICE_BUSY; } - cmdinfo->state &= ~SUBMIT_SENSE_URB; + cmdinfo->state &= ~SUBMIT_STATUS_URB; } if (cmdinfo->state & ALLOC_DATA_IN_URB) { @@ -440,7 +443,7 @@ static int uas_queuecommand_lck(struct scsi_cmnd *cmnd, BUILD_BUG_ON(sizeof(struct uas_cmd_info) > sizeof(struct scsi_pointer)); - if (!cmdinfo->sense_urb && sdev->current_cmnd) + if (!cmdinfo->status_urb && sdev->current_cmnd) return SCSI_MLQUEUE_DEVICE_BUSY; if (blk_rq_tagged(cmnd->request)) { @@ -452,7 +455,7 @@ static int uas_queuecommand_lck(struct scsi_cmnd *cmnd, cmnd->scsi_done = done; - cmdinfo->state = ALLOC_SENSE_URB | SUBMIT_SENSE_URB | + cmdinfo->state = ALLOC_STATUS_URB | SUBMIT_STATUS_URB | ALLOC_CMD_URB | SUBMIT_CMD_URB; switch (cmnd->sc_data_direction) { @@ -475,8 +478,8 @@ static int uas_queuecommand_lck(struct scsi_cmnd *cmnd, err = uas_submit_urbs(cmnd, devinfo, GFP_ATOMIC); if (err) { /* If we did nothing, give up now */ - if (cmdinfo->state & SUBMIT_SENSE_URB) { - usb_free_urb(cmdinfo->sense_urb); + if (cmdinfo->state & SUBMIT_STATUS_URB) { + usb_free_urb(cmdinfo->status_urb); return SCSI_MLQUEUE_DEVICE_BUSY; } spin_lock(&uas_work_lock); @@ -578,6 +581,34 @@ static struct usb_device_id uas_usb_ids[] = { }; MODULE_DEVICE_TABLE(usb, uas_usb_ids); +static int uas_is_interface(struct usb_host_interface *intf) +{ + return (intf->desc.bInterfaceClass == USB_CLASS_MASS_STORAGE && + intf->desc.bInterfaceSubClass == USB_SC_SCSI && + intf->desc.bInterfaceProtocol == USB_PR_UAS); +} + +static int uas_switch_interface(struct usb_device *udev, + struct usb_interface *intf) +{ + int i; + + if (uas_is_interface(intf->cur_altsetting)) + return 0; + + for (i = 0; i < intf->num_altsetting; i++) { + struct usb_host_interface *alt = &intf->altsetting[i]; + if (alt == intf->cur_altsetting) + continue; + if (uas_is_interface(alt)) + return usb_set_interface(udev, + alt->desc.bInterfaceNumber, + alt->desc.bAlternateSetting); + } + + return -ENODEV; +} + static void uas_configure_endpoints(struct uas_dev_info *devinfo) { struct usb_host_endpoint *eps[4] = { }; @@ -651,13 +682,8 @@ static int uas_probe(struct usb_interface *intf, const struct usb_device_id *id) struct uas_dev_info *devinfo; struct usb_device *udev = interface_to_usbdev(intf); - if (id->bInterfaceProtocol == 0x50) { - int ifnum = intf->cur_altsetting->desc.bInterfaceNumber; -/* XXX: Shouldn't assume that 1 is the alternative we want */ - int ret = usb_set_interface(udev, ifnum, 1); - if (ret) - return -ENODEV; - } + if (uas_switch_interface(udev, intf)) + return -ENODEV; devinfo = kmalloc(sizeof(struct uas_dev_info), GFP_KERNEL); if (!devinfo) diff --git a/drivers/uwb/i1480/i1480-est.c b/drivers/uwb/i1480/i1480-est.c index f2eb4d8b76c9..d5de5e131d47 100644 --- a/drivers/uwb/i1480/i1480-est.c +++ b/drivers/uwb/i1480/i1480-est.c @@ -91,7 +91,7 @@ MODULE_LICENSE("GPL"); * * [so we are loaded when this kind device is connected] */ -static struct usb_device_id i1480_est_id_table[] = { +static struct usb_device_id __used i1480_est_id_table[] = { { USB_DEVICE(0x8086, 0xdf3b), }, { USB_DEVICE(0x8086, 0x0c3b), }, { }, diff --git a/drivers/uwb/umc-dev.c b/drivers/uwb/umc-dev.c index 43ea9982e687..ccd2184e05d2 100644 --- a/drivers/uwb/umc-dev.c +++ b/drivers/uwb/umc-dev.c @@ -54,11 +54,8 @@ int umc_device_register(struct umc_dev *umc) err = request_resource(umc->resource.parent, &umc->resource); if (err < 0) { - dev_err(&umc->dev, "can't allocate resource range " - "%016Lx to %016Lx: %d\n", - (unsigned long long)umc->resource.start, - (unsigned long long)umc->resource.end, - err); + dev_err(&umc->dev, "can't allocate resource range %pR: %d\n", + &umc->resource, err); goto error_request_resource; } diff --git a/drivers/uwb/whc-rc.c b/drivers/uwb/whc-rc.c index 73495583c444..70a004aa19db 100644 --- a/drivers/uwb/whc-rc.c +++ b/drivers/uwb/whc-rc.c @@ -449,7 +449,7 @@ static int whcrc_post_reset(struct umc_dev *umc) } /* PCI device ID's that we handle [so it gets loaded] */ -static struct pci_device_id whcrc_id_table[] = { +static struct pci_device_id __used whcrc_id_table[] = { { PCI_DEVICE_CLASS(PCI_CLASS_WIRELESS_WHCI, ~0) }, { /* empty last entry */ } }; diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h index c760991b354a..61b9609e55f2 100644 --- a/include/linux/i2c/twl.h +++ b/include/linux/i2c/twl.h @@ -593,6 +593,13 @@ enum twl4030_usb_mode { struct twl4030_usb_data { enum twl4030_usb_mode usb_mode; + + int (*phy_init)(struct device *dev); + int (*phy_exit)(struct device *dev); + /* Power on/off the PHY */ + int (*phy_power)(struct device *dev, int iD, int on); + /* enable/disable phy clocks */ + int (*phy_set_clock)(struct device *dev, int on); }; struct twl4030_ins { diff --git a/include/linux/usb.h b/include/linux/usb.h index a28eb2592577..bd69b65f3356 100644 --- a/include/linux/usb.h +++ b/include/linux/usb.h @@ -20,6 +20,7 @@ #include <linux/completion.h> /* for struct completion */ #include <linux/sched.h> /* for current && schedule_timeout */ #include <linux/mutex.h> /* for struct mutex */ +#include <linux/pm_runtime.h> /* for runtime PM */ struct usb_device; struct usb_driver; @@ -411,8 +412,6 @@ struct usb_tt; * @quirks: quirks of the whole device * @urbnum: number of URBs submitted for the whole device * @active_duration: total time device is not suspended - * @last_busy: time of last use - * @autosuspend_delay: in jiffies * @connect_time: time device was first connected * @do_remote_wakeup: remote wakeup should be enabled * @reset_resume: needs reset instead of resume @@ -485,8 +484,6 @@ struct usb_device { unsigned long active_duration; #ifdef CONFIG_PM - unsigned long last_busy; - int autosuspend_delay; unsigned long connect_time; unsigned do_remote_wakeup:1; @@ -531,7 +528,7 @@ extern void usb_autopm_put_interface_no_suspend(struct usb_interface *intf); static inline void usb_mark_last_busy(struct usb_device *udev) { - udev->last_busy = jiffies; + pm_runtime_mark_last_busy(&udev->dev); } #else diff --git a/include/linux/usb/ch11.h b/include/linux/usb/ch11.h index 119194c85d10..10ec0699bea4 100644 --- a/include/linux/usb/ch11.h +++ b/include/linux/usb/ch11.h @@ -28,6 +28,13 @@ #define HUB_STOP_TT 11 /* + * Hub class additional requests defined by USB 3.0 spec + * See USB 3.0 spec Table 10-6 + */ +#define HUB_SET_DEPTH 12 +#define HUB_GET_PORT_ERR_COUNT 13 + +/* * Hub Class feature numbers * See USB 2.0 spec Table 11-17 */ @@ -56,6 +63,20 @@ #define USB_PORT_FEAT_C_PORT_L1 23 /* + * Port feature selectors added by USB 3.0 spec. + * See USB 3.0 spec Table 10-7 + */ +#define USB_PORT_FEAT_LINK_STATE 5 +#define USB_PORT_FEAT_U1_TIMEOUT 23 +#define USB_PORT_FEAT_U2_TIMEOUT 24 +#define USB_PORT_FEAT_C_LINK_STATE 25 +#define USB_PORT_FEAT_C_CONFIG_ERR 26 +#define USB_PORT_FEAT_REMOTE_WAKE_MASK 27 +#define USB_PORT_FEAT_BH_PORT_RESET 28 +#define USB_PORT_FEAT_C_BH_PORT_RESET 29 +#define USB_PORT_FEAT_FORCE_LINKPM_ACCEPT 30 + +/* * Hub Status and Hub Change results * See USB 2.0 spec Table 11-19 and Table 11-20 */ @@ -84,6 +105,32 @@ struct usb_port_status { #define USB_PORT_STAT_SUPER_SPEED 0x8000 /* Linux-internal */ /* + * Additions to wPortStatus bit field from USB 3.0 + * See USB 3.0 spec Table 10-10 + */ +#define USB_PORT_STAT_LINK_STATE 0x01e0 +#define USB_SS_PORT_STAT_POWER 0x0200 +#define USB_PORT_STAT_SPEED_5GBPS 0x0000 +/* Valid only if port is enabled */ + +/* + * Definitions for PORT_LINK_STATE values + * (bits 5-8) in wPortStatus + */ +#define USB_SS_PORT_LS_U0 0x0000 +#define USB_SS_PORT_LS_U1 0x0020 +#define USB_SS_PORT_LS_U2 0x0040 +#define USB_SS_PORT_LS_U3 0x0060 +#define USB_SS_PORT_LS_SS_DISABLED 0x0080 +#define USB_SS_PORT_LS_RX_DETECT 0x00a0 +#define USB_SS_PORT_LS_SS_INACTIVE 0x00c0 +#define USB_SS_PORT_LS_POLLING 0x00e0 +#define USB_SS_PORT_LS_RECOVERY 0x0100 +#define USB_SS_PORT_LS_HOT_RESET 0x0120 +#define USB_SS_PORT_LS_COMP_MOD 0x0140 +#define USB_SS_PORT_LS_LOOPBACK 0x0160 + +/* * wPortChange bit field * See USB 2.0 spec Table 11-22 * Bits 0 to 4 shown, bits 5 to 15 are reserved diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h index f917bbbc8901..ab461948b579 100644 --- a/include/linux/usb/ch9.h +++ b/include/linux/usb/ch9.h @@ -124,6 +124,16 @@ #define USB_DEVICE_DEBUG_MODE 6 /* (special devices only) */ /* + * Test Mode Selectors + * See USB 2.0 spec Table 9-7 + */ +#define TEST_J 1 +#define TEST_K 2 +#define TEST_SE0_NAK 3 +#define TEST_PACKET 4 +#define TEST_FORCE_EN 5 + +/* * New Feature Selectors as added by USB 3.0 * See USB 3.0 spec Table 9-6 */ diff --git a/include/linux/usb/hcd.h b/include/linux/usb/hcd.h index 0b6e751ea0b1..dd6ee49a0844 100644 --- a/include/linux/usb/hcd.h +++ b/include/linux/usb/hcd.h @@ -471,6 +471,10 @@ extern void usb_ep0_reinit(struct usb_device *); /*-------------------------------------------------------------------------*/ +/* class requests from USB 3.0 hub spec, table 10-5 */ +#define SetHubDepth (0x3000 | HUB_SET_DEPTH) +#define GetPortErrorCount (0x8000 | HUB_GET_PORT_ERR_COUNT) + /* * Generic bandwidth allocation constants/support */ diff --git a/include/linux/usb/msm_hsusb.h b/include/linux/usb/msm_hsusb.h new file mode 100644 index 000000000000..3675e03b1539 --- /dev/null +++ b/include/linux/usb/msm_hsusb.h @@ -0,0 +1,112 @@ +/* linux/include/asm-arm/arch-msm/hsusb.h + * + * Copyright (C) 2008 Google, Inc. + * Author: Brian Swetland <swetland@google.com> + * Copyright (c) 2009-2010, Code Aurora Forum. All rights reserved. + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef __ASM_ARCH_MSM_HSUSB_H +#define __ASM_ARCH_MSM_HSUSB_H + +#include <linux/types.h> +#include <linux/usb/otg.h> + +/** + * Supported USB modes + * + * USB_PERIPHERAL Only peripheral mode is supported. + * USB_HOST Only host mode is supported. + * USB_OTG OTG mode is supported. + * + */ +enum usb_mode_type { + USB_NONE = 0, + USB_PERIPHERAL, + USB_HOST, + USB_OTG, +}; + +/** + * OTG control + * + * OTG_NO_CONTROL Id/VBUS notifications not required. Useful in host + * only configuration. + * OTG_PHY_CONTROL Id/VBUS notifications comes form USB PHY. + * OTG_PMIC_CONTROL Id/VBUS notifications comes from PMIC hardware. + * OTG_USER_CONTROL Id/VBUS notifcations comes from User via sysfs. + * + */ +enum otg_control_type { + OTG_NO_CONTROL = 0, + OTG_PHY_CONTROL, + OTG_PMIC_CONTROL, + OTG_USER_CONTROL, +}; + +/** + * struct msm_otg_platform_data - platform device data + * for msm72k_otg driver. + * @phy_init_seq: PHY configuration sequence. val, reg pairs + * terminated by -1. + * @vbus_power: VBUS power on/off routine. + * @power_budget: VBUS power budget in mA (0 will be treated as 500mA). + * @mode: Supported mode (OTG/peripheral/host). + * @otg_control: OTG switch controlled by user/Id pin + * @default_mode: Default operational mode. Applicable only if + * OTG switch is controller by user. + * + */ +struct msm_otg_platform_data { + int *phy_init_seq; + void (*vbus_power)(bool on); + unsigned power_budget; + enum usb_mode_type mode; + enum otg_control_type otg_control; + enum usb_mode_type default_mode; + void (*setup_gpio)(enum usb_otg_state state); +}; + +/** + * struct msm_otg: OTG driver data. Shared by HCD and DCD. + * @otg: USB OTG Transceiver structure. + * @pdata: otg device platform data. + * @irq: IRQ number assigned for HSUSB controller. + * @clk: clock struct of usb_hs_clk. + * @pclk: clock struct of usb_hs_pclk. + * @phy_reset_clk: clock struct of usb_phy_clk. + * @core_clk: clock struct of usb_hs_core_clk. + * @regs: ioremapped register base address. + * @inputs: OTG state machine inputs(Id, SessValid etc). + * @sm_work: OTG state machine work. + * @in_lpm: indicates low power mode (LPM) state. + * @async_int: Async interrupt arrived. + * + */ +struct msm_otg { + struct otg_transceiver otg; + struct msm_otg_platform_data *pdata; + int irq; + struct clk *clk; + struct clk *pclk; + struct clk *phy_reset_clk; + struct clk *core_clk; + void __iomem *regs; +#define ID 0 +#define B_SESS_VLD 1 + unsigned long inputs; + struct work_struct sm_work; + atomic_t in_lpm; + int async_int; +}; + +#endif diff --git a/include/linux/usb/msm_hsusb_hw.h b/include/linux/usb/msm_hsusb_hw.h new file mode 100644 index 000000000000..b92e17349c7b --- /dev/null +++ b/include/linux/usb/msm_hsusb_hw.h @@ -0,0 +1,59 @@ +/* + * Copyright (C) 2007 Google, Inc. + * Author: Brian Swetland <swetland@google.com> + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef __LINUX_USB_GADGET_MSM72K_UDC_H__ +#define __LINUX_USB_GADGET_MSM72K_UDC_H__ + +#ifdef CONFIG_ARCH_MSM7X00A +#define USB_SBUSCFG (MSM_USB_BASE + 0x0090) +#else +#define USB_AHBBURST (MSM_USB_BASE + 0x0090) +#define USB_AHBMODE (MSM_USB_BASE + 0x0098) +#endif +#define USB_CAPLENGTH (MSM_USB_BASE + 0x0100) /* 8 bit */ + +#define USB_USBCMD (MSM_USB_BASE + 0x0140) +#define USB_PORTSC (MSM_USB_BASE + 0x0184) +#define USB_OTGSC (MSM_USB_BASE + 0x01A4) +#define USB_USBMODE (MSM_USB_BASE + 0x01A8) + +#define USBCMD_RESET 2 +#define USB_USBINTR (MSM_USB_BASE + 0x0148) + +#define PORTSC_PHCD (1 << 23) /* phy suspend mode */ +#define PORTSC_PTS_MASK (3 << 30) +#define PORTSC_PTS_ULPI (3 << 30) + +#define USB_ULPI_VIEWPORT (MSM_USB_BASE + 0x0170) +#define ULPI_RUN (1 << 30) +#define ULPI_WRITE (1 << 29) +#define ULPI_READ (0 << 29) +#define ULPI_ADDR(n) (((n) & 255) << 16) +#define ULPI_DATA(n) ((n) & 255) +#define ULPI_DATA_READ(n) (((n) >> 8) & 255) + +#define ASYNC_INTR_CTRL (1 << 29) /* Enable async interrupt */ +#define ULPI_STP_CTRL (1 << 30) /* Block communication with PHY */ + +/* OTG definitions */ +#define OTGSC_INTSTS_MASK (0x7f << 16) +#define OTGSC_ID (1 << 8) +#define OTGSC_BSV (1 << 11) +#define OTGSC_IDIS (1 << 16) +#define OTGSC_BSVIS (1 << 19) +#define OTGSC_IDIE (1 << 24) +#define OTGSC_BSVIE (1 << 27) + +#endif /* __LINUX_USB_GADGET_MSM72K_UDC_H__ */ diff --git a/include/linux/usb/musb.h b/include/linux/usb/musb.h index 2387f9fc8138..eb505250940a 100644 --- a/include/linux/usb/musb.h +++ b/include/linux/usb/musb.h @@ -3,7 +3,7 @@ * Inventra (Multidrop) Highspeed Dual-Role Controllers: (M)HDRC. * * Board initialization should put one of these into dev->platform_data, - * probably on some platform_device named "musb_hdrc". It encapsulates + * probably on some platform_device named "musb-hdrc". It encapsulates * key configuration differences between boards. */ @@ -120,14 +120,14 @@ struct musb_hdrc_platform_data { /* Power the device on or off */ int (*set_power)(int state); - /* Turn device clock on or off */ - int (*set_clock)(struct clk *clock, int is_on); - /* MUSB configuration-specific details */ struct musb_hdrc_config *config; /* Architecture specific board data */ void *board_data; + + /* Platform specific struct musb_ops pointer */ + const void *platform_ops; }; diff --git a/include/linux/usb/otg.h b/include/linux/usb/otg.h index 0a5b3711e502..a1a1e7a73ec9 100644 --- a/include/linux/usb/otg.h +++ b/include/linux/usb/otg.h @@ -116,7 +116,7 @@ struct otg_transceiver { /* for board-specific init logic */ extern int otg_set_transceiver(struct otg_transceiver *); -#if defined(CONFIG_NOP_USB_XCEIV) || defined(CONFIG_NOP_USB_XCEIV_MODULE) +#if defined(CONFIG_NOP_USB_XCEIV) || (defined(CONFIG_NOP_USB_XCEIV_MODULE) && defined(MODULE)) /* sometimes transceivers are accessed only through e.g. ULPI */ extern void usb_nop_xceiv_register(void); extern void usb_nop_xceiv_unregister(void); |
