diff options
57 files changed, 5269 insertions, 222 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 7da0899d1fb9..5092a2be83c5 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1369,6 +1369,27 @@ and is between 256 and 4096 characters. It is defined in the file min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this physical address is ignored. + mini2440= [ARM,HW,KNL] + Format:[0..2][b][c][t] + Default: "0tb" + MINI2440 configuration specification: + 0 - The attached screen is the 3.5" TFT + 1 - The attached screen is the 7" TFT + 2 - The VGA Shield is attached (1024x768) + Leaving out the screen size parameter will not load + the TFT driver, and the framebuffer will be left + unconfigured. + b - Enable backlight. The TFT backlight pin will be + linked to the kernel VESA blanking code and a GPIO + LED. This parameter is not necessary when using the + VGA shield. + c - Enable the s3c camera interface. + t - Reserved for enabling touchscreen support. The + touchscreen support is not enabled in the mainstream + kernel as of 2.6.30, a preliminary port can be found + in the "bleeding edge" mini2440 support kernel at + http://repo.or.cz/w/linux-2.6/mini2440.git + mminit_loglevel= [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this parameter allows control of the logging verbosity for diff --git a/MAINTAINERS b/MAINTAINERS index b114632050bf..cf5a46ef6b3f 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -653,6 +653,8 @@ M: laforge@openezx.org L: openezx-devel@lists.openezx.org (subscribers-only) W: http://www.openezx.org/ S: Maintained +T: topgit git://git.openezx.org/openezx.git +F: arch/arm/mach-pxa/ezx.c ARM/FARADAY FA526 PORT P: Paulius Zaleckas @@ -774,11 +776,25 @@ P: Philipp Zabel M: philipp.zabel@gmail.com S: Maintained +ARM/MIOA701 MACHINE SUPPORT +P: Robert Jarzmik +M: robert.jarzmik@free.fr +L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) +F: arch/arm/mach-pxa/mioa701.c +S: Maintained + ARM/NEC MOBILEPRO 900/c MACHINE SUPPORT P: Michael Petchkovsky M: mkpetch@internode.on.net S: Maintained +ARM/OPENMOKO NEO FREERUNNER (GTA02) MACHINE SUPPORT +P: Nelson Castillo +M: arhuaco@freaks-unidos.net +L: openmoko-kernel@lists.openmoko.org (subscribers-only) +W: http://wiki.openmoko.org/wiki/Neo_FreeRunner +S: Supported + ARM/TOSA MACHINE SUPPORT P: Dmitry Eremin-Solenikov M: dbaryshkov@gmail.com @@ -792,6 +808,12 @@ M: marek.vasut@gmail.com W: http://hackndev.com S: Maintained +ARM/PALM TREO 680 SUPPORT +P: Tomas Cech +M: sleep_walker@suse.cz +W: http://hackndev.com +S: Maintained + ARM/PALMZ72 SUPPORT P: Sergey Lapin M: slapin@ossfans.org diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 29475101a7b3..aef63c8e3d2d 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1241,7 +1241,7 @@ endmenu menu "CPU Power Management" -if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_PXA) +if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_PXA || ARCH_S3C64XX) source "drivers/cpufreq/Kconfig" @@ -1272,6 +1272,10 @@ config CPU_FREQ_PXA default y select CPU_FREQ_DEFAULT_GOV_USERSPACE +config CPU_FREQ_S3C64XX + bool "CPUfreq support for Samsung S3C64XX CPUs" + depends on CPU_FREQ && CPU_S3C6410 + endif source "drivers/cpuidle/Kconfig" diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S index 01d49be3b2ca..4515728c5345 100644 --- a/arch/arm/boot/compressed/head.S +++ b/arch/arm/boot/compressed/head.S @@ -674,6 +674,15 @@ proc_types: b __armv4_mmu_cache_off b __armv5tej_mmu_cache_flush +#ifdef CONFIG_CPU_FEROCEON_OLD_ID + /* this conflicts with the standard ARMv5TE entry */ + .long 0x41009260 @ Old Feroceon + .long 0xff00fff0 + b __armv4_mmu_cache_on + b __armv4_mmu_cache_off + b __armv5tej_mmu_cache_flush +#endif + .word 0x66015261 @ FA526 .word 0xff01fff1 b __fa526_cache_on diff --git a/arch/arm/common/gic.c b/arch/arm/common/gic.c index 664c7b8b1ba8..337741f734ac 100644 --- a/arch/arm/common/gic.c +++ b/arch/arm/common/gic.c @@ -117,7 +117,7 @@ static int gic_set_cpu(unsigned int irq, const struct cpumask *mask_val) u32 val; spin_lock(&irq_controller_lock); - irq_desc[irq].cpu = cpu; + irq_desc[irq].node = cpu; val = readl(reg) & ~(0xff << shift); val |= 1 << (cpu + shift); writel(val, reg); diff --git a/arch/arm/common/vic.c b/arch/arm/common/vic.c index 887c6eb3a18a..6ed89836e908 100644 --- a/arch/arm/common/vic.c +++ b/arch/arm/common/vic.c @@ -229,14 +229,18 @@ static int vic_set_wake(unsigned int irq, unsigned int on) { struct vic_device *v = vic_from_irq(irq); unsigned int off = irq & 31; + u32 bit = 1 << off; if (!v) return -EINVAL; + if (!(bit & v->resume_sources)) + return -EINVAL; + if (on) - v->resume_irqs |= 1 << off; + v->resume_irqs |= bit; else - v->resume_irqs &= ~(1 << off); + v->resume_irqs &= ~bit; return 0; } diff --git a/arch/arm/configs/mini2440_defconfig b/arch/arm/configs/mini2440_defconfig new file mode 100644 index 000000000000..e49ed40f3be7 --- /dev/null +++ b/arch/arm/configs/mini2440_defconfig @@ -0,0 +1,2097 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.30-rc6 +# Wed May 20 12:29:51 2009 +# +CONFIG_ARM=y +CONFIG_HAVE_PWM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +# CONFIG_GENERIC_TIME is not set +# CONFIG_GENERIC_CLOCKEVENTS is not set +CONFIG_MMU=y +CONFIG_NO_IOPORT=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +# CONFIG_LOCALVERSION_AUTO is not set +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_POSIX_MQUEUE=y +CONFIG_POSIX_MQUEUE_SYSCTL=y +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set + +# +# RCU Subsystem +# +CONFIG_CLASSIC_RCU=y +# CONFIG_TREE_RCU is not set +# CONFIG_PREEMPT_RCU is not set +# CONFIG_TREE_RCU_TRACE is not set +# CONFIG_PREEMPT_RCU_TRACE is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=17 +# CONFIG_GROUP_SCHED is not set +# CONFIG_CGROUPS is not set +# CONFIG_SYSFS_DEPRECATED_V2 is not set +CONFIG_RELAY=y +CONFIG_NAMESPACES=y +CONFIG_UTS_NS=y +CONFIG_IPC_NS=y +# CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set +# CONFIG_NET_NS is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_RD_GZIP=y +CONFIG_RD_BZIP2=y +CONFIG_RD_LZMA=y +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_ANON_INODES=y +# CONFIG_EMBEDDED is not set +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_STRIP_ASM_SYMS=y +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_AIO=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLUB_DEBUG=y +# CONFIG_COMPAT_BRK is not set +# CONFIG_SLAB is not set +CONFIG_SLUB=y +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_CLK=y +# CONFIG_SLOW_WORK is not set +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +CONFIG_MODULE_FORCE_LOAD=y +CONFIG_MODULE_UNLOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_BLOCK=y +CONFIG_LBD=y +# CONFIG_BLK_DEV_BSG is not set +CONFIG_BLK_DEV_INTEGRITY=y + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_FREEZER=y + +# +# System Type +# +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_GEMINI is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KIRKWOOD is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_LOKI is not set +# CONFIG_ARCH_MV78XX0 is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +CONFIG_ARCH_S3C2410=y +# CONFIG_ARCH_S3C64XX is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_DAVINCI is not set +# CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_MSM is not set +# CONFIG_ARCH_W90X900 is not set +CONFIG_PLAT_S3C24XX=y +CONFIG_S3C2410_CLOCK=y +CONFIG_CPU_S3C244X=y +CONFIG_S3C24XX_PWM=y +CONFIG_S3C24XX_GPIO_EXTRA=0 +CONFIG_S3C2410_DMA=y +# CONFIG_S3C2410_DMA_DEBUG is not set +CONFIG_S3C24XX_ADC=y +CONFIG_PLAT_S3C=y +CONFIG_CPU_LLSERIAL_S3C2440_ONLY=y +CONFIG_CPU_LLSERIAL_S3C2440=y + +# +# Boot options +# +# CONFIG_S3C_BOOT_WATCHDOG is not set +# CONFIG_S3C_BOOT_ERROR_RESET is not set +CONFIG_S3C_BOOT_UART_FORCE_FIFO=y + +# +# Power management +# +# CONFIG_S3C2410_PM_DEBUG is not set +# CONFIG_S3C2410_PM_CHECK is not set +CONFIG_S3C_LOWLEVEL_UART_PORT=0 +CONFIG_S3C_GPIO_SPACE=0 + +# +# S3C2400 Machines +# +CONFIG_S3C2410_PM=y +CONFIG_S3C2410_GPIO=y + +# +# S3C2410 Machines +# +# CONFIG_ARCH_SMDK2410 is not set +# CONFIG_ARCH_H1940 is not set +# CONFIG_MACH_N30 is not set +# CONFIG_ARCH_BAST is not set +# CONFIG_MACH_OTOM is not set +# CONFIG_MACH_AML_M5900 is not set +# CONFIG_MACH_TCT_HAMMER is not set +# CONFIG_MACH_VR1000 is not set +# CONFIG_MACH_QT2410 is not set + +# +# S3C2412 Machines +# +# CONFIG_MACH_JIVE is not set +# CONFIG_MACH_SMDK2413 is not set +# CONFIG_MACH_SMDK2412 is not set +# CONFIG_MACH_VSTMS is not set +CONFIG_CPU_S3C2440=y +CONFIG_S3C2440_DMA=y + +# +# S3C2440 Machines +# +# CONFIG_MACH_ANUBIS is not set +# CONFIG_MACH_OSIRIS is not set +# CONFIG_MACH_RX3715 is not set +# CONFIG_ARCH_S3C2440 is not set +# CONFIG_MACH_NEXCODER_2440 is not set +# CONFIG_MACH_AT2440EVB is not set +CONFIG_MACH_MINI2440=y + +# +# S3C2442 Machines +# + +# +# S3C2443 Machines +# +# CONFIG_MACH_SMDK2443 is not set + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM920T=y +CONFIG_CPU_32v4T=y +CONFIG_CPU_ABRT_EV4T=y +CONFIG_CPU_PABRT_NOIFAR=y +CONFIG_CPU_CACHE_V4WT=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +CONFIG_ARM_THUMB=y +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set +# CONFIG_OUTER_CACHE is not set + +# +# Bus support +# +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +CONFIG_VMSPLIT_3G=y +# CONFIG_VMSPLIT_2G is not set +# CONFIG_VMSPLIT_1G is not set +CONFIG_PAGE_OFFSET=0xC0000000 +# CONFIG_PREEMPT is not set +CONFIG_HZ=200 +CONFIG_AEABI=y +# CONFIG_OABI_COMPAT is not set +CONFIG_ARCH_FLATMEM_HAS_HOLES=y +# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set +# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set +# CONFIG_HIGHMEM is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_PHYS_ADDR_T_64BIT is not set +CONFIG_ZONE_DMA_FLAG=0 +CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y +CONFIG_HAVE_MLOCK=y +CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0 +CONFIG_ZBOOT_ROM_BSS=0 +CONFIG_CMDLINE="" +# CONFIG_XIP_KERNEL is not set +CONFIG_KEXEC=y +CONFIG_ATAGS_PROC=y + +# +# CPU Power Management +# +CONFIG_CPU_IDLE=y +CONFIG_CPU_IDLE_GOV_LADDER=y + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y +CONFIG_BINFMT_AOUT=m +CONFIG_BINFMT_MISC=m + +# +# Power management options +# +CONFIG_PM=y +# CONFIG_PM_DEBUG is not set +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND=y +CONFIG_SUSPEND_FREEZER=y +CONFIG_APM_EMULATION=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +CONFIG_PACKET_MMAP=y +CONFIG_UNIX=y +CONFIG_XFRM=y +CONFIG_XFRM_USER=m +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +CONFIG_NET_KEY=m +# CONFIG_NET_KEY_MIGRATE is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +CONFIG_IP_ADVANCED_ROUTER=y +CONFIG_ASK_IP_FIB_HASH=y +# CONFIG_IP_FIB_TRIE is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_MULTIPLE_TABLES=y +CONFIG_IP_ROUTE_MULTIPATH=y +CONFIG_IP_ROUTE_VERBOSE=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +CONFIG_IP_MROUTE=y +CONFIG_IP_PIMSM_V1=y +CONFIG_IP_PIMSM_V2=y +# CONFIG_ARPD is not set +CONFIG_SYN_COOKIES=y +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=m +CONFIG_INET_TCP_DIAG=m +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETWORK_SECMARK is not set +CONFIG_NETFILTER=y +# CONFIG_NETFILTER_DEBUG is not set +CONFIG_NETFILTER_ADVANCED=y +CONFIG_BRIDGE_NETFILTER=y + +# +# Core Netfilter Configuration +# +# CONFIG_NETFILTER_NETLINK_QUEUE is not set +# CONFIG_NETFILTER_NETLINK_LOG is not set +# CONFIG_NF_CONNTRACK is not set +# CONFIG_NETFILTER_XTABLES is not set +# CONFIG_IP_VS is not set + +# +# IP: Netfilter Configuration +# +# CONFIG_NF_DEFRAG_IPV4 is not set +# CONFIG_IP_NF_QUEUE is not set +# CONFIG_IP_NF_IPTABLES is not set +# CONFIG_IP_NF_ARPTABLES is not set +# CONFIG_BRIDGE_NF_EBTABLES is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +CONFIG_STP=m +CONFIG_GARP=m +CONFIG_BRIDGE=m +# CONFIG_NET_DSA is not set +CONFIG_VLAN_8021Q=m +CONFIG_VLAN_8021Q_GVRP=y +# CONFIG_DECNET is not set +CONFIG_LLC=m +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_PHONET is not set +# CONFIG_NET_SCHED is not set +# CONFIG_DCB is not set + +# +# Network testing +# +CONFIG_NET_PKTGEN=m +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +CONFIG_BT=m +CONFIG_BT_L2CAP=m +CONFIG_BT_SCO=m +CONFIG_BT_RFCOMM=m +CONFIG_BT_RFCOMM_TTY=y +CONFIG_BT_BNEP=m +CONFIG_BT_BNEP_MC_FILTER=y +CONFIG_BT_BNEP_PROTO_FILTER=y +CONFIG_BT_HIDP=m + +# +# Bluetooth device drivers +# +CONFIG_BT_HCIBTUSB=m +CONFIG_BT_HCIBTSDIO=m +CONFIG_BT_HCIUART=m +CONFIG_BT_HCIUART_H4=y +CONFIG_BT_HCIUART_BCSP=y +CONFIG_BT_HCIUART_LL=y +CONFIG_BT_HCIBCM203X=m +CONFIG_BT_HCIBPA10X=m +CONFIG_BT_HCIBFUSB=m +CONFIG_BT_HCIVHCI=m +# CONFIG_AF_RXRPC is not set +CONFIG_FIB_RULES=y +CONFIG_WIRELESS=y +CONFIG_CFG80211=m +CONFIG_CFG80211_REG_DEBUG=y +CONFIG_WIRELESS_OLD_REGULATORY=y +CONFIG_WIRELESS_EXT=y +CONFIG_WIRELESS_EXT_SYSFS=y +CONFIG_LIB80211=m +CONFIG_LIB80211_CRYPT_WEP=m +CONFIG_LIB80211_CRYPT_CCMP=m +CONFIG_LIB80211_CRYPT_TKIP=m +# CONFIG_LIB80211_DEBUG is not set +CONFIG_MAC80211=m + +# +# Rate control algorithm selection +# +CONFIG_MAC80211_RC_MINSTREL=y +# CONFIG_MAC80211_RC_DEFAULT_PID is not set +CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y +CONFIG_MAC80211_RC_DEFAULT="minstrel" +CONFIG_MAC80211_MESH=y +CONFIG_MAC80211_LEDS=y +# CONFIG_MAC80211_DEBUGFS is not set +# CONFIG_MAC80211_DEBUG_MENU is not set +# CONFIG_WIMAX is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +# CONFIG_FIRMWARE_IN_KERNEL is not set +CONFIG_EXTRA_FIRMWARE="" +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +CONFIG_CONNECTOR=m +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +CONFIG_MTD_CONCAT=y +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_TESTS is not set +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +CONFIG_FTL=y +CONFIG_NFTL=y +CONFIG_NFTL_RW=y +CONFIG_INFTL=y +CONFIG_RFD_FTL=y +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_STAA=y +CONFIG_MTD_CFI_UTIL=y +CONFIG_MTD_RAM=y +CONFIG_MTD_ROM=y +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PHYSMAP is not set +# CONFIG_MTD_ARM_INTEGRATOR is not set +# CONFIG_MTD_IMPA7 is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_DATAFLASH is not set +# CONFIG_MTD_M25P80 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_VERIFY_WRITE=y +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +# CONFIG_MTD_NAND_GPIO is not set +CONFIG_MTD_NAND_IDS=y +CONFIG_MTD_NAND_S3C2410=y +# CONFIG_MTD_NAND_S3C2410_DEBUG is not set +# CONFIG_MTD_NAND_S3C2410_HWECC is not set +# CONFIG_MTD_NAND_S3C2410_CLKSTOP is not set +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_NANDSIM is not set +CONFIG_MTD_NAND_PLATFORM=y +# CONFIG_MTD_ALAUDA is not set +# CONFIG_MTD_ONENAND is not set + +# +# LPDDR flash memory drivers +# +CONFIG_MTD_LPDDR=y +CONFIG_MTD_QINFO_PROBE=y + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=m +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +CONFIG_BLK_DEV_NBD=m +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=65536 +# CONFIG_BLK_DEV_XIP is not set +CONFIG_CDROM_PKTCDVD=m +CONFIG_CDROM_PKTCDVD_BUFFERS=8 +# CONFIG_CDROM_PKTCDVD_WCACHE is not set +# CONFIG_ATA_OVER_ETH is not set +CONFIG_MISC_DEVICES=y +# CONFIG_ICS932S401 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_ISL29003 is not set +# CONFIG_C2PORT is not set + +# +# EEPROM support +# +CONFIG_EEPROM_AT24=y +# CONFIG_EEPROM_AT25 is not set +# CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_93CX6 is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=m +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_SCSI_PROC_FS is not set + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=m +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +CONFIG_CHR_DEV_SG=m +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +# CONFIG_SCSI_LOWLEVEL is not set +# CONFIG_SCSI_DH is not set +# CONFIG_SCSI_OSD_INITIATOR is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +CONFIG_COMPAT_NET_DEV_OPS=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +CONFIG_TUN=m +# CONFIG_VETH is not set +# CONFIG_PHYLIB is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_AX88796 is not set +# CONFIG_SMC91X is not set +CONFIG_DM9000=y +CONFIG_DM9000_DEBUGLEVEL=4 +# CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL is not set +# CONFIG_ENC28J60 is not set +# CONFIG_ETHOC is not set +# CONFIG_SMC911X is not set +# CONFIG_SMSC911X is not set +# CONFIG_DNET is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set +# CONFIG_B44 is not set +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +CONFIG_WLAN_80211=y +CONFIG_LIBERTAS=m +# CONFIG_LIBERTAS_USB is not set +CONFIG_LIBERTAS_SDIO=m +# CONFIG_LIBERTAS_SPI is not set +# CONFIG_LIBERTAS_DEBUG is not set +# CONFIG_LIBERTAS_THINFIRM is not set +# CONFIG_AT76C50X_USB is not set +# CONFIG_USB_ZD1201 is not set +# CONFIG_USB_NET_RNDIS_WLAN is not set +# CONFIG_RTL8187 is not set +# CONFIG_MAC80211_HWSIM is not set +# CONFIG_P54_COMMON is not set +# CONFIG_AR9170_USB is not set +CONFIG_HOSTAP=m +CONFIG_HOSTAP_FIRMWARE=y +CONFIG_HOSTAP_FIRMWARE_NVRAM=y +# CONFIG_B43 is not set +# CONFIG_B43LEGACY is not set +CONFIG_ZD1211RW=m +CONFIG_ZD1211RW_DEBUG=y +# CONFIG_RT2X00 is not set + +# +# Enable WiMAX (Networking options) to see the WiMAX drivers +# + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +CONFIG_PPP=m +CONFIG_PPP_MULTILINK=y +CONFIG_PPP_FILTER=y +CONFIG_PPP_ASYNC=m +CONFIG_PPP_SYNC_TTY=m +CONFIG_PPP_DEFLATE=m +CONFIG_PPP_BSDCOMP=m +CONFIG_PPP_MPPE=m +# CONFIG_PPPOE is not set +# CONFIG_PPPOL2TP is not set +# CONFIG_SLIP is not set +CONFIG_SLHC=m +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y +CONFIG_INPUT_FF_MEMLESS=y +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=y +CONFIG_INPUT_EVBUG=m + +# +# Input Device Drivers +# +CONFIG_INPUT_KEYBOARD=y +# CONFIG_KEYBOARD_ATKBD is not set +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_LKKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_NEWTON is not set +# CONFIG_KEYBOARD_STOWAWAY is not set +CONFIG_KEYBOARD_GPIO=y +CONFIG_INPUT_MOUSE=y +CONFIG_MOUSE_PS2=y +CONFIG_MOUSE_PS2_ALPS=y +CONFIG_MOUSE_PS2_LOGIPS2PP=y +CONFIG_MOUSE_PS2_SYNAPTICS=y +CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set +# CONFIG_MOUSE_PS2_TOUCHKIT is not set +# CONFIG_MOUSE_SERIAL is not set +# CONFIG_MOUSE_APPLETOUCH is not set +# CONFIG_MOUSE_BCM5974 is not set +# CONFIG_MOUSE_VSXXXAA is not set +# CONFIG_MOUSE_GPIO is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +CONFIG_INPUT_TOUCHSCREEN=y +# CONFIG_TOUCHSCREEN_ADS7846 is not set +# CONFIG_TOUCHSCREEN_AD7877 is not set +# CONFIG_TOUCHSCREEN_AD7879_I2C is not set +# CONFIG_TOUCHSCREEN_AD7879_SPI is not set +# CONFIG_TOUCHSCREEN_AD7879 is not set +# CONFIG_TOUCHSCREEN_FUJITSU is not set +# CONFIG_TOUCHSCREEN_GUNZE is not set +# CONFIG_TOUCHSCREEN_ELO is not set +# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set +# CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_INEXIO is not set +# CONFIG_TOUCHSCREEN_MK712 is not set +# CONFIG_TOUCHSCREEN_PENMOUNT is not set +# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set +# CONFIG_TOUCHSCREEN_TOUCHWIN is not set +# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set +# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set +# CONFIG_TOUCHSCREEN_TSC2007 is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +CONFIG_SERIO=y +CONFIG_SERIO_SERPORT=y +CONFIG_SERIO_LIBPS2=y +CONFIG_SERIO_RAW=y +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +CONFIG_VT_HW_CONSOLE_BINDING=y +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_SAMSUNG=y +CONFIG_SERIAL_SAMSUNG_UARTS=3 +CONFIG_SERIAL_SAMSUNG_CONSOLE=y +CONFIG_SERIAL_S3C2440=y +# CONFIG_SERIAL_MAX3100 is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=128 +CONFIG_IPMI_HANDLER=m +# CONFIG_IPMI_PANIC_EVENT is not set +CONFIG_IPMI_DEVICE_INTERFACE=m +CONFIG_IPMI_SI=m +CONFIG_IPMI_WATCHDOG=m +CONFIG_IPMI_POWEROFF=m +CONFIG_HW_RANDOM=y +# CONFIG_HW_RANDOM_TIMERIOMEM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y +CONFIG_I2C_ALGOBIT=y + +# +# I2C Hardware Bus support +# + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +# CONFIG_I2C_GPIO is not set +# CONFIG_I2C_OCORES is not set +CONFIG_I2C_S3C2410=y +CONFIG_I2C_SIMTEC=y + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_MAX6875 is not set +CONFIG_SENSORS_TSL2550=m +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +CONFIG_SPI=y +# CONFIG_SPI_DEBUG is not set +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +CONFIG_SPI_BITBANG=y +# CONFIG_SPI_GPIO is not set +CONFIG_SPI_S3C24XX=y +# CONFIG_SPI_S3C24XX_GPIO is not set + +# +# SPI Protocol Masters +# +CONFIG_SPI_SPIDEV=y +# CONFIG_SPI_TLE62X0 is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_DEBUG_GPIO is not set +CONFIG_GPIO_SYSFS=y + +# +# Memory mapped GPIO expanders: +# + +# +# I2C GPIO expanders: +# +# CONFIG_GPIO_MAX732X is not set +# CONFIG_GPIO_PCA953X is not set +# CONFIG_GPIO_PCF857X is not set + +# +# PCI GPIO expanders: +# + +# +# SPI GPIO expanders: +# +# CONFIG_GPIO_MAX7301 is not set +# CONFIG_GPIO_MCP23S08 is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_AD7414 is not set +# CONFIG_SENSORS_AD7418 is not set +# CONFIG_SENSORS_ADCXX is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1029 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ADT7462 is not set +# CONFIG_SENSORS_ADT7470 is not set +# CONFIG_SENSORS_ADT7473 is not set +# CONFIG_SENSORS_ADT7475 is not set +# CONFIG_SENSORS_ATXP1 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set +# CONFIG_SENSORS_G760A is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set +# CONFIG_SENSORS_IBMAEM is not set +# CONFIG_SENSORS_IBMPEX is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM70 is not set +CONFIG_SENSORS_LM75=y +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_LM92 is not set +# CONFIG_SENSORS_LM93 is not set +# CONFIG_SENSORS_LTC4215 is not set +# CONFIG_SENSORS_LTC4245 is not set +# CONFIG_SENSORS_LM95241 is not set +# CONFIG_SENSORS_MAX1111 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_MAX6650 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_PC87427 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_SHT15 is not set +# CONFIG_SENSORS_DME1737 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47M192 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_ADS7828 is not set +# CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_VT1211 is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83791D is not set +# CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83793 is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83L786NG is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_SENSORS_LIS3_SPI is not set +# CONFIG_HWMON_DEBUG_CHIP is not set +CONFIG_THERMAL=m +# CONFIG_THERMAL_HWMON is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_S3C2410_WATCHDOG=y + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +CONFIG_SSB_POSSIBLE=y + +# +# Sonics Silicon Backplane +# +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_MFD_ASIC3 is not set +# CONFIG_HTC_EGPIO is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_TPS65010 is not set +# CONFIG_TWL4030_CORE is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_MFD_T7L66XB is not set +# CONFIG_MFD_TC6387XB is not set +# CONFIG_MFD_TC6393XB is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_MFD_PCF50633 is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +CONFIG_VIDEO_DEV=m +CONFIG_VIDEO_V4L2_COMMON=m +CONFIG_VIDEO_ALLOW_V4L1=y +CONFIG_VIDEO_V4L1_COMPAT=y +CONFIG_DVB_CORE=m +CONFIG_VIDEO_MEDIA=m + +# +# Multimedia drivers +# +# CONFIG_MEDIA_ATTACH is not set +CONFIG_MEDIA_TUNER=m +# CONFIG_MEDIA_TUNER_CUSTOMISE is not set +CONFIG_MEDIA_TUNER_SIMPLE=m +CONFIG_MEDIA_TUNER_TDA8290=m +CONFIG_MEDIA_TUNER_TDA9887=m +CONFIG_MEDIA_TUNER_TEA5761=m +CONFIG_MEDIA_TUNER_TEA5767=m +CONFIG_MEDIA_TUNER_MT20XX=m +CONFIG_MEDIA_TUNER_XC2028=m +CONFIG_MEDIA_TUNER_XC5000=m +CONFIG_MEDIA_TUNER_MC44S803=m +CONFIG_VIDEO_V4L2=m +CONFIG_VIDEO_V4L1=m +CONFIG_VIDEOBUF_GEN=m +CONFIG_VIDEO_CAPTURE_DRIVERS=y +# CONFIG_VIDEO_ADV_DEBUG is not set +# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set +CONFIG_VIDEO_HELPER_CHIPS_AUTO=y +# CONFIG_VIDEO_VIVI is not set +# CONFIG_VIDEO_CPIA is not set +# CONFIG_VIDEO_CPIA2 is not set +# CONFIG_VIDEO_SAA5246A is not set +# CONFIG_VIDEO_SAA5249 is not set +# CONFIG_VIDEO_AU0828 is not set +CONFIG_SOC_CAMERA=m +# CONFIG_SOC_CAMERA_MT9M001 is not set +# CONFIG_SOC_CAMERA_MT9M111 is not set +# CONFIG_SOC_CAMERA_MT9T031 is not set +# CONFIG_SOC_CAMERA_MT9V022 is not set +# CONFIG_SOC_CAMERA_TW9910 is not set +CONFIG_SOC_CAMERA_PLATFORM=m +# CONFIG_SOC_CAMERA_OV772X is not set +# CONFIG_VIDEO_SH_MOBILE_CEU is not set +CONFIG_V4L_USB_DRIVERS=y +# CONFIG_USB_VIDEO_CLASS is not set +CONFIG_USB_VIDEO_CLASS_INPUT_EVDEV=y +CONFIG_USB_GSPCA=m +# CONFIG_USB_M5602 is not set +# CONFIG_USB_STV06XX is not set +# CONFIG_USB_GSPCA_CONEX is not set +# CONFIG_USB_GSPCA_ETOMS is not set +# CONFIG_USB_GSPCA_FINEPIX is not set +# CONFIG_USB_GSPCA_MARS is not set +# CONFIG_USB_GSPCA_MR97310A is not set +# CONFIG_USB_GSPCA_OV519 is not set +# CONFIG_USB_GSPCA_OV534 is not set +# CONFIG_USB_GSPCA_PAC207 is not set +# CONFIG_USB_GSPCA_PAC7311 is not set +# CONFIG_USB_GSPCA_SONIXB is not set +# CONFIG_USB_GSPCA_SONIXJ is not set +# CONFIG_USB_GSPCA_SPCA500 is not set +# CONFIG_USB_GSPCA_SPCA501 is not set +# CONFIG_USB_GSPCA_SPCA505 is not set +# CONFIG_USB_GSPCA_SPCA506 is not set +# CONFIG_USB_GSPCA_SPCA508 is not set +# CONFIG_USB_GSPCA_SPCA561 is not set +# CONFIG_USB_GSPCA_SQ905 is not set +# CONFIG_USB_GSPCA_SQ905C is not set +# CONFIG_USB_GSPCA_STK014 is not set +# CONFIG_USB_GSPCA_SUNPLUS is not set +# CONFIG_USB_GSPCA_T613 is not set +# CONFIG_USB_GSPCA_TV8532 is not set +# CONFIG_USB_GSPCA_VC032X is not set +CONFIG_USB_GSPCA_ZC3XX=m +# CONFIG_VIDEO_PVRUSB2 is not set +# CONFIG_VIDEO_HDPVR is not set +# CONFIG_VIDEO_EM28XX is not set +# CONFIG_VIDEO_CX231XX is not set +# CONFIG_VIDEO_USBVISION is not set +# CONFIG_USB_VICAM is not set +# CONFIG_USB_IBMCAM is not set +# CONFIG_USB_KONICAWC is not set +# CONFIG_USB_QUICKCAM_MESSENGER is not set +# CONFIG_USB_ET61X251 is not set +# CONFIG_VIDEO_OVCAMCHIP is not set +# CONFIG_USB_OV511 is not set +# CONFIG_USB_SE401 is not set +# CONFIG_USB_SN9C102 is not set +# CONFIG_USB_STV680 is not set +# CONFIG_USB_ZC0301 is not set +# CONFIG_USB_PWC is not set +# CONFIG_USB_PWC_INPUT_EVDEV is not set +# CONFIG_USB_ZR364XX is not set +# CONFIG_USB_STKWEBCAM is not set +# CONFIG_USB_S2255 is not set +CONFIG_RADIO_ADAPTERS=y +# CONFIG_USB_DSBR is not set +# CONFIG_USB_SI470X is not set +# CONFIG_USB_MR800 is not set +# CONFIG_RADIO_TEA5764 is not set +# CONFIG_DVB_DYNAMIC_MINORS is not set +CONFIG_DVB_CAPTURE_DRIVERS=y +# CONFIG_TTPCI_EEPROM is not set + +# +# Supported USB Adapters +# +# CONFIG_DVB_USB is not set +# CONFIG_DVB_SIANO_SMS1XXX is not set + +# +# Supported FlexCopII (B2C2) Adapters +# +# CONFIG_DVB_B2C2_FLEXCOP is not set + +# +# Supported DVB Frontends +# +# CONFIG_DVB_FE_CUSTOMISE is not set +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +CONFIG_FB=y +CONFIG_FIRMWARE_EDID=y +# CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +CONFIG_FB_MODE_HELPERS=y +CONFIG_FB_TILEBLITTING=y + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_UVESA is not set +# CONFIG_FB_S1D13XXX is not set +CONFIG_FB_S3C2410=y +# CONFIG_FB_S3C2410_DEBUG is not set +# CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set +# CONFIG_FB_BROADSHEET is not set +CONFIG_BACKLIGHT_LCD_SUPPORT=y +CONFIG_LCD_CLASS_DEVICE=y +# CONFIG_LCD_LTV350QV is not set +# CONFIG_LCD_ILI9320 is not set +# CONFIG_LCD_TDO24M is not set +# CONFIG_LCD_VGG2432A4 is not set +CONFIG_LCD_PLATFORM=y +CONFIG_BACKLIGHT_CLASS_DEVICE=y +# CONFIG_BACKLIGHT_GENERIC is not set +CONFIG_BACKLIGHT_PWM=y + +# +# Display device support +# +CONFIG_DISPLAY_SUPPORT=y + +# +# Display hardware drivers +# + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +CONFIG_FRAMEBUFFER_CONSOLE=y +CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y +CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y +CONFIG_FONTS=y +CONFIG_FONT_8x8=y +# CONFIG_FONT_8x16 is not set +# CONFIG_FONT_6x11 is not set +# CONFIG_FONT_7x14 is not set +# CONFIG_FONT_PEARL_8x8 is not set +# CONFIG_FONT_ACORN_8x8 is not set +CONFIG_FONT_MINI_4x6=y +# CONFIG_FONT_SUN8x16 is not set +# CONFIG_FONT_SUN12x22 is not set +# CONFIG_FONT_10x18 is not set +CONFIG_LOGO=y +# CONFIG_LOGO_LINUX_MONO is not set +# CONFIG_LOGO_LINUX_VGA16 is not set +CONFIG_LOGO_LINUX_CLUT224=y +CONFIG_SOUND=y +CONFIG_SOUND_OSS_CORE=y +CONFIG_SND=y +CONFIG_SND_TIMER=y +CONFIG_SND_PCM=y +CONFIG_SND_HWDEP=m +CONFIG_SND_RAWMIDI=m +CONFIG_SND_JACK=y +CONFIG_SND_SEQUENCER=m +CONFIG_SND_SEQ_DUMMY=m +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=m +CONFIG_SND_PCM_OSS=m +CONFIG_SND_PCM_OSS_PLUGINS=y +CONFIG_SND_SEQUENCER_OSS=y +CONFIG_SND_DYNAMIC_MINORS=y +CONFIG_SND_SUPPORT_OLD_API=y +CONFIG_SND_VERBOSE_PROCFS=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set +# CONFIG_SND_DRIVERS is not set +# CONFIG_SND_ARM is not set +# CONFIG_SND_SPI is not set +CONFIG_SND_USB=y +CONFIG_SND_USB_AUDIO=m +CONFIG_SND_USB_CAIAQ=m +CONFIG_SND_USB_CAIAQ_INPUT=y +CONFIG_SND_SOC=y +CONFIG_SND_S3C24XX_SOC=y +CONFIG_SND_S3C24XX_SOC_I2S=y +# CONFIG_SND_S3C24XX_SOC_LN2440SBC_ALC650 is not set +CONFIG_SND_S3C24XX_SOC_S3C24XX_UDA134X=y +CONFIG_SND_SOC_I2C_AND_SPI=y +# CONFIG_SND_SOC_ALL_CODECS is not set +CONFIG_SND_SOC_L3=y +CONFIG_SND_SOC_UDA134X=y +# CONFIG_SOUND_PRIME is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +CONFIG_HIDRAW=y + +# +# USB Input Devices +# +CONFIG_USB_HID=y +CONFIG_HID_PID=y +CONFIG_USB_HIDDEV=y + +# +# Special HID drivers +# +CONFIG_HID_A4TECH=y +CONFIG_HID_APPLE=y +CONFIG_HID_BELKIN=y +CONFIG_HID_CHERRY=y +CONFIG_HID_CHICONY=y +CONFIG_HID_CYPRESS=y +# CONFIG_DRAGONRISE_FF is not set +CONFIG_HID_EZKEY=y +CONFIG_HID_KYE=y +CONFIG_HID_GYRATION=y +CONFIG_HID_KENSINGTON=y +CONFIG_HID_LOGITECH=y +# CONFIG_LOGITECH_FF is not set +# CONFIG_LOGIRUMBLEPAD2_FF is not set +CONFIG_HID_MICROSOFT=y +CONFIG_HID_MONTEREY=y +CONFIG_HID_NTRIG=y +CONFIG_HID_PANTHERLORD=y +# CONFIG_PANTHERLORD_FF is not set +CONFIG_HID_PETALYNX=y +CONFIG_HID_SAMSUNG=y +CONFIG_HID_SONY=y +CONFIG_HID_SUNPLUS=y +# CONFIG_GREENASIA_FF is not set +CONFIG_HID_TOPSEED=y +# CONFIG_THRUSTMASTER_FF is not set +# CONFIG_ZEROPLUS_FF is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +# CONFIG_USB_ARCH_HAS_EHCI is not set +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +# CONFIG_USB_DEVICE_CLASS is not set +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_SUSPEND is not set +# CONFIG_USB_OTG is not set +# CONFIG_USB_MON is not set +# CONFIG_USB_WUSB is not set +# CONFIG_USB_WUSB_CBAF is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_OXU210HP_HCD is not set +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_HWA_HCD is not set +# CONFIG_USB_MUSB_HDRC is not set +# CONFIG_USB_GADGET_MUSB_HDRC is not set + +# +# USB Device Class drivers +# +CONFIG_USB_ACM=m +# CONFIG_USB_PRINTER is not set +CONFIG_USB_WDM=m +# CONFIG_USB_TMC is not set + +# +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may +# + +# +# also be needed; see USB_STORAGE Help for more info +# +CONFIG_USB_STORAGE=m +# CONFIG_USB_STORAGE_DEBUG is not set +CONFIG_USB_STORAGE_DATAFAB=m +# CONFIG_USB_STORAGE_FREECOM is not set +CONFIG_USB_STORAGE_ISD200=m +CONFIG_USB_STORAGE_USBAT=m +CONFIG_USB_STORAGE_SDDR09=m +CONFIG_USB_STORAGE_SDDR55=m +CONFIG_USB_STORAGE_JUMPSHOT=m +CONFIG_USB_STORAGE_ALAUDA=m +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +CONFIG_USB_LIBUSUAL=y + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB port drivers +# +CONFIG_USB_SERIAL=m +# CONFIG_USB_EZUSB is not set +# CONFIG_USB_SERIAL_GENERIC is not set +# CONFIG_USB_SERIAL_AIRCABLE is not set +# CONFIG_USB_SERIAL_ARK3116 is not set +# CONFIG_USB_SERIAL_BELKIN is not set +# CONFIG_USB_SERIAL_CH341 is not set +# CONFIG_USB_SERIAL_WHITEHEAT is not set +# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set +CONFIG_USB_SERIAL_CP210X=m +# CONFIG_USB_SERIAL_CYPRESS_M8 is not set +# CONFIG_USB_SERIAL_EMPEG is not set +CONFIG_USB_SERIAL_FTDI_SIO=m +# CONFIG_USB_SERIAL_FUNSOFT is not set +# CONFIG_USB_SERIAL_VISOR is not set +# CONFIG_USB_SERIAL_IPAQ is not set +# CONFIG_USB_SERIAL_IR is not set +# CONFIG_USB_SERIAL_EDGEPORT is not set +# CONFIG_USB_SERIAL_EDGEPORT_TI is not set +# CONFIG_USB_SERIAL_GARMIN is not set +# CONFIG_USB_SERIAL_IPW is not set +# CONFIG_USB_SERIAL_IUU is not set +# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set +# CONFIG_USB_SERIAL_KEYSPAN is not set +# CONFIG_USB_SERIAL_KLSI is not set +# CONFIG_USB_SERIAL_KOBIL_SCT is not set +# CONFIG_USB_SERIAL_MCT_U232 is not set +# CONFIG_USB_SERIAL_MOS7720 is not set +# CONFIG_USB_SERIAL_MOS7840 is not set +# CONFIG_USB_SERIAL_MOTOROLA is not set +# CONFIG_USB_SERIAL_NAVMAN is not set +# CONFIG_USB_SERIAL_PL2303 is not set +# CONFIG_USB_SERIAL_OTI6858 is not set +# CONFIG_USB_SERIAL_QUALCOMM is not set +CONFIG_USB_SERIAL_SPCP8X5=m +# CONFIG_USB_SERIAL_HP4X is not set +# CONFIG_USB_SERIAL_SAFE is not set +# CONFIG_USB_SERIAL_SIEMENS_MPI is not set +# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set +# CONFIG_USB_SERIAL_SYMBOL is not set +# CONFIG_USB_SERIAL_TI is not set +# CONFIG_USB_SERIAL_CYBERJACK is not set +# CONFIG_USB_SERIAL_XIRCOM is not set +# CONFIG_USB_SERIAL_OPTION is not set +# CONFIG_USB_SERIAL_OMNINET is not set +# CONFIG_USB_SERIAL_OPTICON is not set +# CONFIG_USB_SERIAL_DEBUG is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_SEVSEG is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_VST is not set +CONFIG_USB_GADGET=y +# CONFIG_USB_GADGET_DEBUG is not set +# CONFIG_USB_GADGET_DEBUG_FILES is not set +# CONFIG_USB_GADGET_DEBUG_FS is not set +CONFIG_USB_GADGET_VBUS_DRAW=2 +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_AT91 is not set +# CONFIG_USB_GADGET_ATMEL_USBA is not set +# CONFIG_USB_GADGET_FSL_USB2 is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_PXA25X is not set +# CONFIG_USB_GADGET_PXA27X is not set +CONFIG_USB_GADGET_S3C2410=y +CONFIG_USB_S3C2410=y +# CONFIG_USB_S3C2410_DEBUG is not set +# CONFIG_USB_GADGET_IMX is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_FSL_QE is not set +# CONFIG_USB_GADGET_CI13XXX is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +CONFIG_USB_ZERO=m +CONFIG_USB_ETH=m +CONFIG_USB_ETH_RNDIS=y +CONFIG_USB_GADGETFS=m +CONFIG_USB_FILE_STORAGE=m +# CONFIG_USB_FILE_STORAGE_TEST is not set +CONFIG_USB_G_SERIAL=m +# CONFIG_USB_MIDI_GADGET is not set +# CONFIG_USB_G_PRINTER is not set +CONFIG_USB_CDC_COMPOSITE=m + +# +# OTG and related infrastructure +# +# CONFIG_USB_GPIO_VBUS is not set +# CONFIG_NOP_USB_XCEIV is not set +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD/SDIO Card Drivers +# +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_BOUNCE=y +CONFIG_SDIO_UART=y +# CONFIG_MMC_TEST is not set + +# +# MMC/SD/SDIO Host Controller Drivers +# +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SPI=y +CONFIG_MMC_S3C=y +# CONFIG_MEMSTICK is not set +# CONFIG_ACCESSIBILITY is not set +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=y + +# +# LED drivers +# +CONFIG_LEDS_S3C24XX=y +# CONFIG_LEDS_PCA9532 is not set +CONFIG_LEDS_GPIO=y +CONFIG_LEDS_GPIO_PLATFORM=y +# CONFIG_LEDS_LP5521 is not set +# CONFIG_LEDS_PCA955X is not set +# CONFIG_LEDS_DAC124S085 is not set +# CONFIG_LEDS_PWM is not set +# CONFIG_LEDS_BD2802 is not set + +# +# LED Triggers +# +CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_TIMER=y +CONFIG_LEDS_TRIGGER_HEARTBEAT=y +CONFIG_LEDS_TRIGGER_BACKLIGHT=y +CONFIG_LEDS_TRIGGER_GPIO=y +CONFIG_LEDS_TRIGGER_DEFAULT_ON=y + +# +# iptables trigger is under Netfilter config (LED target) +# +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +CONFIG_RTC_INTF_DEV_UIE_EMUL=y +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set +# CONFIG_RTC_DRV_RX8581 is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_M41T94 is not set +# CONFIG_RTC_DRV_DS1305 is not set +# CONFIG_RTC_DRV_DS1390 is not set +# CONFIG_RTC_DRV_MAX6902 is not set +# CONFIG_RTC_DRV_R9701 is not set +# CONFIG_RTC_DRV_RS5C348 is not set +# CONFIG_RTC_DRV_DS3234 is not set + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1286 is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_BQ4802 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +CONFIG_RTC_DRV_S3C=y +CONFIG_DMADEVICES=y + +# +# DMA Devices +# +# CONFIG_AUXDISPLAY is not set +# CONFIG_REGULATOR is not set +# CONFIG_UIO is not set +# CONFIG_STAGING is not set + +# +# File systems +# +CONFIG_EXT2_FS=m +CONFIG_EXT2_FS_XATTR=y +CONFIG_EXT2_FS_POSIX_ACL=y +CONFIG_EXT2_FS_SECURITY=y +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set +CONFIG_EXT3_FS_XATTR=y +CONFIG_EXT3_FS_POSIX_ACL=y +CONFIG_EXT3_FS_SECURITY=y +# CONFIG_EXT4_FS is not set +CONFIG_JBD=y +# CONFIG_JBD_DEBUG is not set +CONFIG_FS_MBCACHE=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +CONFIG_FS_POSIX_ACL=y +CONFIG_FILE_LOCKING=y +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_BTRFS_FS is not set +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +CONFIG_AUTOFS_FS=y +CONFIG_AUTOFS4_FS=y +# CONFIG_FUSE_FS is not set +CONFIG_GENERIC_ACL=y + +# +# Caches +# +# CONFIG_FSCACHE is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +CONFIG_TMPFS_POSIX_ACL=y +# CONFIG_HUGETLB_PAGE is not set +CONFIG_CONFIGFS_FS=m +CONFIG_MISC_FILESYSTEMS=y +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_ECRYPT_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +CONFIG_CRAMFS=y +# CONFIG_SQUASHFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +CONFIG_ROMFS_FS=y +# CONFIG_ROMFS_BACKED_BY_BLOCK is not set +# CONFIG_ROMFS_BACKED_BY_MTD is not set +CONFIG_ROMFS_BACKED_BY_BOTH=y +CONFIG_ROMFS_ON_BLOCK=y +CONFIG_ROMFS_ON_MTD=y +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +# CONFIG_NILFS2_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +CONFIG_NFS_V3_ACL=y +CONFIG_NFS_V4=y +CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_ACL_SUPPORT=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +CONFIG_BSD_DISKLABEL=y +CONFIG_MINIX_SUBPARTITION=y +CONFIG_SOLARIS_X86_PARTITION=y +CONFIG_UNIXWARE_DISKLABEL=y +CONFIG_LDM_PARTITION=y +# CONFIG_LDM_DEBUG is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +CONFIG_EFI_PARTITION=y +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="cp437" +CONFIG_NLS_CODEPAGE_437=m +CONFIG_NLS_CODEPAGE_737=m +CONFIG_NLS_CODEPAGE_775=m +CONFIG_NLS_CODEPAGE_850=m +CONFIG_NLS_CODEPAGE_852=m +CONFIG_NLS_CODEPAGE_855=m +CONFIG_NLS_CODEPAGE_857=m +CONFIG_NLS_CODEPAGE_860=m +CONFIG_NLS_CODEPAGE_861=m +CONFIG_NLS_CODEPAGE_862=m +CONFIG_NLS_CODEPAGE_863=m +CONFIG_NLS_CODEPAGE_864=m +CONFIG_NLS_CODEPAGE_865=m +CONFIG_NLS_CODEPAGE_866=m +CONFIG_NLS_CODEPAGE_869=m +CONFIG_NLS_CODEPAGE_936=m +CONFIG_NLS_CODEPAGE_950=m +CONFIG_NLS_CODEPAGE_932=m +CONFIG_NLS_CODEPAGE_949=m +CONFIG_NLS_CODEPAGE_874=m +CONFIG_NLS_ISO8859_8=m +CONFIG_NLS_CODEPAGE_1250=m +CONFIG_NLS_CODEPAGE_1251=m +CONFIG_NLS_ASCII=m +CONFIG_NLS_ISO8859_1=m +CONFIG_NLS_ISO8859_2=m +CONFIG_NLS_ISO8859_3=m +CONFIG_NLS_ISO8859_4=m +CONFIG_NLS_ISO8859_5=m +CONFIG_NLS_ISO8859_6=m +CONFIG_NLS_ISO8859_7=m +CONFIG_NLS_ISO8859_9=m +CONFIG_NLS_ISO8859_13=m +CONFIG_NLS_ISO8859_14=m +CONFIG_NLS_ISO8859_15=m +CONFIG_NLS_KOI8_R=m +CONFIG_NLS_KOI8_U=m +CONFIG_NLS_UTF8=m +# CONFIG_DLM is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +# CONFIG_ENABLE_WARN_DEPRECATED is not set +# CONFIG_ENABLE_MUST_CHECK is not set +CONFIG_FRAME_WARN=1024 +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +CONFIG_DEBUG_FS=y +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_DETECT_HUNG_TASK=y +# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set +CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0 +# CONFIG_SCHED_DEBUG is not set +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_SLUB_DEBUG_ON is not set +# CONFIG_SLUB_STATS is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_DEBUG_NOTIFIERS is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y +# CONFIG_PAGE_POISONING is not set +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_TRACING_SUPPORT=y + +# +# Tracers +# +# CONFIG_FUNCTION_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_EVENT_TRACER is not set +# CONFIG_BOOT_TRACER is not set +# CONFIG_TRACE_BRANCH_PROFILING is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_KMEMTRACE is not set +# CONFIG_WORKQUEUE_TRACER is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_DYNAMIC_DEBUG is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +CONFIG_ARM_UNWIND=y +CONFIG_DEBUG_USER=y +# CONFIG_DEBUG_ERRORS is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_LL is not set +CONFIG_DEBUG_S3C_UART=0 + +# +# Security options +# +CONFIG_KEYS=y +# CONFIG_KEYS_DEBUG_PROC_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set +CONFIG_SECURITY_FILE_CAPABILITIES=y +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_FIPS=y +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_ALGAPI2=y +CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_AEAD2=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_BLKCIPHER2=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_HASH2=y +CONFIG_CRYPTO_RNG=m +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_PCOMP=y +CONFIG_CRYPTO_MANAGER=y +CONFIG_CRYPTO_MANAGER2=y +CONFIG_CRYPTO_GF128MUL=m +CONFIG_CRYPTO_NULL=m +CONFIG_CRYPTO_WORKQUEUE=y +CONFIG_CRYPTO_CRYPTD=m +CONFIG_CRYPTO_AUTHENC=m +CONFIG_CRYPTO_TEST=m + +# +# Authenticated Encryption with Associated Data +# +CONFIG_CRYPTO_CCM=m +CONFIG_CRYPTO_GCM=m +CONFIG_CRYPTO_SEQIV=m + +# +# Block modes +# +CONFIG_CRYPTO_CBC=y +CONFIG_CRYPTO_CTR=m +CONFIG_CRYPTO_CTS=m +CONFIG_CRYPTO_ECB=y +CONFIG_CRYPTO_LRW=m +CONFIG_CRYPTO_PCBC=m +CONFIG_CRYPTO_XTS=m + +# +# Hash modes +# +CONFIG_CRYPTO_HMAC=y +CONFIG_CRYPTO_XCBC=m + +# +# Digest +# +CONFIG_CRYPTO_CRC32C=m +CONFIG_CRYPTO_MD4=m +CONFIG_CRYPTO_MD5=y +CONFIG_CRYPTO_MICHAEL_MIC=y +CONFIG_CRYPTO_RMD128=m +CONFIG_CRYPTO_RMD160=m +CONFIG_CRYPTO_RMD256=m +CONFIG_CRYPTO_RMD320=m +CONFIG_CRYPTO_SHA1=m +CONFIG_CRYPTO_SHA256=m +CONFIG_CRYPTO_SHA512=m +CONFIG_CRYPTO_TGR192=m +CONFIG_CRYPTO_WP512=m + +# +# Ciphers +# +CONFIG_CRYPTO_AES=y +CONFIG_CRYPTO_ANUBIS=m +CONFIG_CRYPTO_ARC4=y +CONFIG_CRYPTO_BLOWFISH=m +CONFIG_CRYPTO_CAMELLIA=m +CONFIG_CRYPTO_CAST5=m +CONFIG_CRYPTO_CAST6=m +CONFIG_CRYPTO_DES=y +CONFIG_CRYPTO_FCRYPT=m +CONFIG_CRYPTO_KHAZAD=m +CONFIG_CRYPTO_SALSA20=m +CONFIG_CRYPTO_SEED=m +CONFIG_CRYPTO_SERPENT=m +CONFIG_CRYPTO_TEA=m +CONFIG_CRYPTO_TWOFISH=m +CONFIG_CRYPTO_TWOFISH_COMMON=m + +# +# Compression +# +CONFIG_CRYPTO_DEFLATE=m +CONFIG_CRYPTO_ZLIB=m +CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +CONFIG_CRYPTO_ANSI_CPRNG=m +CONFIG_CRYPTO_HW=y +# CONFIG_BINARY_PRINTF is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +CONFIG_GENERIC_FIND_LAST_BIT=y +CONFIG_CRC_CCITT=m +CONFIG_CRC16=m +CONFIG_CRC_T10DIF=y +CONFIG_CRC_ITU_T=y +CONFIG_CRC32=y +CONFIG_CRC7=y +CONFIG_LIBCRC32C=m +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_LZO_COMPRESS=m +CONFIG_LZO_DECOMPRESS=m +CONFIG_DECOMPRESS_GZIP=y +CONFIG_DECOMPRESS_BZIP2=y +CONFIG_DECOMPRESS_LZMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_DMA=y +CONFIG_NLATTR=y diff --git a/arch/arm/include/asm/unistd.h b/arch/arm/include/asm/unistd.h index 94cc58ef61ae..0e97b8cb77d5 100644 --- a/arch/arm/include/asm/unistd.h +++ b/arch/arm/include/asm/unistd.h @@ -389,6 +389,8 @@ #define __NR_inotify_init1 (__NR_SYSCALL_BASE+360) #define __NR_preadv (__NR_SYSCALL_BASE+361) #define __NR_pwritev (__NR_SYSCALL_BASE+362) +#define __NR_rt_tgsigqueueinfo (__NR_SYSCALL_BASE+363) +#define __NR_perf_counter_open (__NR_SYSCALL_BASE+364) /* * The following SWIs are ARM private. diff --git a/arch/arm/kernel/calls.S b/arch/arm/kernel/calls.S index 1680e9e9c831..f776e72a4cb8 100644 --- a/arch/arm/kernel/calls.S +++ b/arch/arm/kernel/calls.S @@ -372,6 +372,8 @@ /* 360 */ CALL(sys_inotify_init1) CALL(sys_preadv) CALL(sys_pwritev) + CALL(sys_rt_tgsigqueueinfo) + CALL(sys_perf_counter_open) #ifndef syscalls_counted .equ syscalls_padding, ((NR_syscalls + 3) & ~3) - NR_syscalls #define syscalls_counted diff --git a/arch/arm/kernel/irq.c b/arch/arm/kernel/irq.c index 6874c7dca75a..096f600dc8d8 100644 --- a/arch/arm/kernel/irq.c +++ b/arch/arm/kernel/irq.c @@ -167,7 +167,7 @@ void __init init_IRQ(void) #ifdef CONFIG_SMP cpumask_setall(bad_irq_desc.affinity); - bad_irq_desc.cpu = smp_processor_id(); + bad_irq_desc.node = smp_processor_id(); #endif init_arch_irq(); } @@ -176,7 +176,7 @@ void __init init_IRQ(void) static void route_irq(struct irq_desc *desc, unsigned int irq, unsigned int cpu) { - pr_debug("IRQ%u: moving from cpu%u to cpu%u\n", irq, desc->cpu, cpu); + pr_debug("IRQ%u: moving from cpu%u to cpu%u\n", irq, desc->node, cpu); spin_lock_irq(&desc->lock); desc->chip->set_affinity(irq, cpumask_of(cpu)); @@ -195,7 +195,7 @@ void migrate_irqs(void) for (i = 0; i < NR_IRQS; i++) { struct irq_desc *desc = irq_desc + i; - if (desc->cpu == cpu) { + if (desc->node == cpu) { unsigned int newcpu = cpumask_any_and(desc->affinity, cpu_online_mask); if (newcpu >= nr_cpu_ids) { diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index 1585423699ee..39196dff478c 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -114,9 +114,6 @@ void arm_machine_restart(char mode, const char *cmd) /* * Function pointers to optional machine specific functions */ -void (*pm_idle)(void); -EXPORT_SYMBOL(pm_idle); - void (*pm_power_off)(void); EXPORT_SYMBOL(pm_power_off); @@ -130,20 +127,19 @@ EXPORT_SYMBOL_GPL(arm_pm_restart); */ static void default_idle(void) { - if (hlt_counter) - cpu_relax(); - else { - local_irq_disable(); - if (!need_resched()) - arch_idle(); - local_irq_enable(); - } + if (!need_resched()) + arch_idle(); + local_irq_enable(); } +void (*pm_idle)(void) = default_idle; +EXPORT_SYMBOL(pm_idle); + /* - * The idle thread. We try to conserve power, while trying to keep - * overall latency low. The architecture specific idle is passed - * a value to indicate the level of "idleness" of the system. + * The idle thread, has rather strange semantics for calling pm_idle, + * but this is what x86 does and we need to do the same, so that + * things like cpuidle get called in the same way. The only difference + * is that we always respect 'hlt_counter' to prevent low power idle. */ void cpu_idle(void) { @@ -151,21 +147,31 @@ void cpu_idle(void) /* endless idle loop with no priority at all */ while (1) { - void (*idle)(void) = pm_idle; - + tick_nohz_stop_sched_tick(1); + leds_event(led_idle_start); + while (!need_resched()) { #ifdef CONFIG_HOTPLUG_CPU - if (cpu_is_offline(smp_processor_id())) { - leds_event(led_idle_start); - cpu_die(); - } + if (cpu_is_offline(smp_processor_id())) + cpu_die(); #endif - if (!idle) - idle = default_idle; - leds_event(led_idle_start); - tick_nohz_stop_sched_tick(1); - while (!need_resched()) - idle(); + local_irq_disable(); + if (hlt_counter) { + local_irq_enable(); + cpu_relax(); + } else { + stop_critical_timings(); + pm_idle(); + start_critical_timings(); + /* + * This will eventually be removed - pm_idle + * functions should always return with IRQs + * enabled. + */ + WARN_ON(irqs_disabled()); + local_irq_enable(); + } + } leds_event(led_idle_end); tick_nohz_restart_sched_tick(); preempt_enable_no_resched(); @@ -352,6 +358,23 @@ asm( ".section .text\n" " .size kernel_thread_helper, . - kernel_thread_helper\n" " .previous"); +#ifdef CONFIG_ARM_UNWIND +extern void kernel_thread_exit(long code); +asm( ".section .text\n" +" .align\n" +" .type kernel_thread_exit, #function\n" +"kernel_thread_exit:\n" +" .fnstart\n" +" .cantunwind\n" +" bl do_exit\n" +" nop\n" +" .fnend\n" +" .size kernel_thread_exit, . - kernel_thread_exit\n" +" .previous"); +#else +#define kernel_thread_exit do_exit +#endif + /* * Create a kernel thread. */ @@ -363,7 +386,7 @@ pid_t kernel_thread(int (*fn)(void *), void *arg, unsigned long flags) regs.ARM_r1 = (unsigned long)arg; regs.ARM_r2 = (unsigned long)fn; - regs.ARM_r3 = (unsigned long)do_exit; + regs.ARM_r3 = (unsigned long)kernel_thread_exit; regs.ARM_pc = (unsigned long)kernel_thread_helper; regs.ARM_cpsr = SVC_MODE | PSR_ENDSTATE; diff --git a/arch/arm/kernel/unwind.c b/arch/arm/kernel/unwind.c index 1dedc2c7ff49..dd56e11f339a 100644 --- a/arch/arm/kernel/unwind.c +++ b/arch/arm/kernel/unwind.c @@ -212,7 +212,8 @@ static int unwind_exec_insn(struct unwind_ctrl_block *ctrl) ctrl->vrs[14] = *vsp++; ctrl->vrs[SP] = (unsigned long)vsp; } else if (insn == 0xb0) { - ctrl->vrs[PC] = ctrl->vrs[LR]; + if (ctrl->vrs[PC] == 0) + ctrl->vrs[PC] = ctrl->vrs[LR]; /* no further processing */ ctrl->entries = 0; } else if (insn == 0xb1) { @@ -309,18 +310,20 @@ int unwind_frame(struct stackframe *frame) } while (ctrl.entries > 0) { - int urc; - - if (ctrl.vrs[SP] < low || ctrl.vrs[SP] >= high) - return -URC_FAILURE; - urc = unwind_exec_insn(&ctrl); + int urc = unwind_exec_insn(&ctrl); if (urc < 0) return urc; + if (ctrl.vrs[SP] < low || ctrl.vrs[SP] >= high) + return -URC_FAILURE; } if (ctrl.vrs[PC] == 0) ctrl.vrs[PC] = ctrl.vrs[LR]; + /* check for infinite loop */ + if (frame->pc == ctrl.vrs[PC]) + return -URC_FAILURE; + frame->fp = ctrl.vrs[FP]; frame->sp = ctrl.vrs[SP]; frame->lr = ctrl.vrs[LR]; @@ -332,7 +335,6 @@ int unwind_frame(struct stackframe *frame) void unwind_backtrace(struct pt_regs *regs, struct task_struct *tsk) { struct stackframe frame; - unsigned long high, low; register unsigned long current_sp asm ("sp"); pr_debug("%s(regs = %p tsk = %p)\n", __func__, regs, tsk); @@ -362,9 +364,6 @@ void unwind_backtrace(struct pt_regs *regs, struct task_struct *tsk) frame.pc = thread_saved_pc(tsk); } - low = frame.sp & ~(THREAD_SIZE - 1); - high = low + THREAD_SIZE; - while (1) { int urc; unsigned long where = frame.pc; diff --git a/arch/arm/kernel/vmlinux.lds.S b/arch/arm/kernel/vmlinux.lds.S index 6c0779792546..4340bf3d2c84 100644 --- a/arch/arm/kernel/vmlinux.lds.S +++ b/arch/arm/kernel/vmlinux.lds.S @@ -84,6 +84,14 @@ SECTIONS *(.exitcall.exit) *(.ARM.exidx.exit.text) *(.ARM.extab.exit.text) +#ifndef CONFIG_HOTPLUG_CPU + *(.ARM.exidx.cpuexit.text) + *(.ARM.extab.cpuexit.text) +#endif +#ifndef CONFIG_HOTPLUG + *(.ARM.exidx.devexit.text) + *(.ARM.extab.devexit.text) +#endif #ifndef CONFIG_MMU *(.fixup) *(__ex_table) diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index ba528f85749c..b0665f161c03 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -302,7 +302,7 @@ int omap2_wait_clock_ready(void __iomem *reg, u32 mask, const char *name) udelay(1); } - if (i < MAX_CLOCK_ENABLE_WAIT) + if (i <= MAX_CLOCK_ENABLE_WAIT) pr_debug("Clock %s stable after %d loops\n", name, i); else printk(KERN_ERR "Clock %s didn't enable in %d tries\n", diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c index 9e43fe5209d3..045da923e75b 100644 --- a/arch/arm/mach-omap2/clock34xx.c +++ b/arch/arm/mach-omap2/clock34xx.c @@ -286,6 +286,20 @@ static struct omap_clk omap34xx_clks[] = { #define MIN_SDRC_DLL_LOCK_FREQ 83000000 +#define CYCLES_PER_MHZ 1000000 + +/* Scale factor for fixed-point arith in omap3_core_dpll_m2_set_rate() */ +#define SDRC_MPURATE_SCALE 8 + +/* 2^SDRC_MPURATE_BASE_SHIFT: MPU MHz that SDRC_MPURATE_LOOPS is defined for */ +#define SDRC_MPURATE_BASE_SHIFT 9 + +/* + * SDRC_MPURATE_LOOPS: Number of MPU loops to execute at + * 2^MPURATE_BASE_SHIFT MHz for SDRC to stabilize + */ +#define SDRC_MPURATE_LOOPS 96 + /** * omap3_dpll_recalc - recalculate DPLL rate * @clk: DPLL struct clk @@ -709,7 +723,8 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) { u32 new_div = 0; u32 unlock_dll = 0; - unsigned long validrate, sdrcrate; + u32 c; + unsigned long validrate, sdrcrate, mpurate; struct omap_sdrc_params *sp; if (!clk || !rate) @@ -718,18 +733,15 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) if (clk != &dpll3_m2_ck) return -EINVAL; - if (rate == clk->rate) - return 0; - validrate = omap2_clksel_round_rate_div(clk, rate, &new_div); if (validrate != rate) return -EINVAL; sdrcrate = sdrc_ick.rate; if (rate > clk->rate) - sdrcrate <<= ((rate / clk->rate) - 1); + sdrcrate <<= ((rate / clk->rate) >> 1); else - sdrcrate >>= ((clk->rate / rate) - 1); + sdrcrate >>= ((clk->rate / rate) >> 1); sp = omap2_sdrc_get_params(sdrcrate); if (!sp) @@ -740,17 +752,25 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) unlock_dll = 1; } + /* + * XXX This only needs to be done when the CPU frequency changes + */ + mpurate = arm_fck.rate / CYCLES_PER_MHZ; + c = (mpurate << SDRC_MPURATE_SCALE) >> SDRC_MPURATE_BASE_SHIFT; + c += 1; /* for safety */ + c *= SDRC_MPURATE_LOOPS; + c >>= SDRC_MPURATE_SCALE; + if (c == 0) + c = 1; + pr_debug("clock: changing CORE DPLL rate from %lu to %lu\n", clk->rate, validrate); pr_debug("clock: SDRC timing params used: %08x %08x %08x\n", sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb); - /* REVISIT: SRAM code doesn't support other M2 divisors yet */ - WARN_ON(new_div != 1 && new_div != 2); - - /* REVISIT: Add SDRC_MR changing to this code also */ omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla, - sp->actim_ctrlb, new_div, unlock_dll); + sp->actim_ctrlb, new_div, unlock_dll, c, + sp->mr, rate > clk->rate); return 0; } diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index 32afd9448216..3a86b0f66031 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -21,6 +21,7 @@ #include <linux/kernel.h> #include <linux/init.h> #include <linux/io.h> +#include <linux/clk.h> #include <asm/tlb.h> @@ -241,6 +242,40 @@ void __init omap2_map_common_io(void) omapfb_reserve_sdram(); } +/* + * omap2_init_reprogram_sdrc - reprogram SDRC timing parameters + * + * Sets the CORE DPLL3 M2 divider to the same value that it's at + * currently. This has the effect of setting the SDRC SDRAM AC timing + * registers to the values currently defined by the kernel. Currently + * only defined for OMAP3; will return 0 if called on OMAP2. Returns + * -EINVAL if the dpll3_m2_ck cannot be found, 0 if called on OMAP2, + * or passes along the return value of clk_set_rate(). + */ +static int __init _omap2_init_reprogram_sdrc(void) +{ + struct clk *dpll3_m2_ck; + int v = -EINVAL; + long rate; + + if (!cpu_is_omap34xx()) + return 0; + + dpll3_m2_ck = clk_get(NULL, "dpll3_m2_ck"); + if (!dpll3_m2_ck) + return -EINVAL; + + rate = clk_get_rate(dpll3_m2_ck); + pr_info("Reprogramming SDRC clock to %ld Hz\n", rate); + v = clk_set_rate(dpll3_m2_ck, rate); + if (v) + pr_err("dpll3_m2_clk rate change failed: %d\n", v); + + clk_put(dpll3_m2_ck); + + return v; +} + void __init omap2_init_common_hw(struct omap_sdrc_params *sp) { omap2_mux_init(); @@ -249,6 +284,7 @@ void __init omap2_init_common_hw(struct omap_sdrc_params *sp) clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps); omap2_clk_init(); omap2_sdrc_init(sp); + _omap2_init_reprogram_sdrc(); #endif gpmc_init(); } diff --git a/arch/arm/mach-omap2/powerdomain.c b/arch/arm/mach-omap2/powerdomain.c index 73e2971b1757..983f1cb676be 100644 --- a/arch/arm/mach-omap2/powerdomain.c +++ b/arch/arm/mach-omap2/powerdomain.c @@ -1099,7 +1099,7 @@ int pwrdm_wait_transition(struct powerdomain *pwrdm) (c++ < PWRDM_TRANSITION_BAILOUT)) udelay(1); - if (c >= PWRDM_TRANSITION_BAILOUT) { + if (c > PWRDM_TRANSITION_BAILOUT) { printk(KERN_ERR "powerdomain: waited too long for " "powerdomain %s to complete transition\n", pwrdm->name); return -EAGAIN; diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index c080c82521e1..f41f8d96ddba 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -3,13 +3,12 @@ * * Omap3 specific functions that need to be run in internal SRAM * - * (C) Copyright 2007 - * Texas Instruments Inc. - * Rajendra Nayak <rnayak@ti.com> + * Copyright (C) 2004, 2007, 2008 Texas Instruments, Inc. + * Copyright (C) 2008 Nokia Corporation * - * (C) Copyright 2004 - * Texas Instruments, <www.ti.com> + * Rajendra Nayak <rnayak@ti.com> * Richard Woodruff <r-woodruff2@ti.com> + * Paul Walmsley * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as @@ -37,61 +36,112 @@ .text +/* r4 parameters */ +#define SDRC_NO_UNLOCK_DLL 0x0 +#define SDRC_UNLOCK_DLL 0x1 + +/* SDRC_DLLA_CTRL bit settings */ +#define FIXEDDELAY_SHIFT 24 +#define FIXEDDELAY_MASK (0xff << FIXEDDELAY_SHIFT) +#define DLLIDLE_MASK 0x4 + +/* + * SDRC_DLLA_CTRL default values: TI hardware team indicates that + * FIXEDDELAY should be initialized to 0xf. This apparently was + * empirically determined during process testing, so no derivation + * was provided. + */ +#define FIXEDDELAY_DEFAULT (0x0f << FIXEDDELAY_SHIFT) + +/* SDRC_DLLA_STATUS bit settings */ +#define LOCKSTATUS_MASK 0x4 + +/* SDRC_POWER bit settings */ +#define SRFRONIDLEREQ_MASK 0x40 +#define PWDENA_MASK 0x4 + +/* CM_IDLEST1_CORE bit settings */ +#define ST_SDRC_MASK 0x2 + +/* CM_ICLKEN1_CORE bit settings */ +#define EN_SDRC_MASK 0x2 + +/* CM_CLKSEL1_PLL bit settings */ +#define CORE_DPLL_CLKOUT_DIV_SHIFT 0x1b + /* - * Change frequency of core dpll - * r0 = sdrc_rfr_ctrl r1 = sdrc_actim_ctrla r2 = sdrc_actim_ctrlb r3 = M2 - * r4 = Unlock SDRC DLL? (1 = yes, 0 = no) -- only unlock DLL for + * omap3_sram_configure_core_dpll - change DPLL3 M2 divider + * r0 = new SDRC_RFR_CTRL register contents + * r1 = new SDRC_ACTIM_CTRLA register contents + * r2 = new SDRC_ACTIM_CTRLB register contents + * r3 = new M2 divider setting (only 1 and 2 supported right now) + * r4 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for * SDRC rates < 83MHz + * r5 = number of MPU cycles to wait for SDRC to stabilize after + * reprogramming the SDRC when switching to a slower MPU speed + * r6 = new SDRC_MR_0 register value + * r7 = increasing SDRC rate? (1 = yes, 0 = no) + * */ ENTRY(omap3_sram_configure_core_dpll) stmfd sp!, {r1-r12, lr} @ store regs to stack ldr r4, [sp, #52] @ pull extra args off the stack + ldr r5, [sp, #56] @ load extra args from the stack + ldr r6, [sp, #60] @ load extra args from the stack + ldr r7, [sp, #64] @ load extra args from the stack dsb @ flush buffered writes to interconnect - cmp r3, #0x2 - blne configure_sdrc - cmp r4, #0x1 + cmp r7, #1 @ if increasing SDRC clk rate, + bleq configure_sdrc @ program the SDRC regs early (for RFR) + cmp r4, #SDRC_UNLOCK_DLL @ set the intended DLL state bleq unlock_dll blne lock_dll - bl sdram_in_selfrefresh @ put the SDRAM in self refresh - bl configure_core_dpll - bl enable_sdrc - cmp r4, #0x1 + bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC + bl configure_core_dpll @ change the DPLL3 M2 divider + bl enable_sdrc @ take SDRC out of idle + cmp r4, #SDRC_UNLOCK_DLL @ wait for DLL status to change bleq wait_dll_unlock blne wait_dll_lock - cmp r3, #0x1 - blne configure_sdrc + cmp r7, #1 @ if increasing SDRC clk rate, + beq return_to_sdram @ return to SDRAM code, otherwise, + bl configure_sdrc @ reprogram SDRC regs now + mov r12, r5 + bl wait_clk_stable @ wait for SDRC to stabilize +return_to_sdram: isb @ prevent speculative exec past here mov r0, #0 @ return value ldmfd sp!, {r1-r12, pc} @ restore regs and return unlock_dll: ldr r11, omap3_sdrc_dlla_ctrl ldr r12, [r11] - orr r12, r12, #0x4 + and r12, r12, #FIXEDDELAY_MASK + orr r12, r12, #FIXEDDELAY_DEFAULT + orr r12, r12, #DLLIDLE_MASK str r12, [r11] @ (no OCP barrier needed) bx lr lock_dll: ldr r11, omap3_sdrc_dlla_ctrl ldr r12, [r11] - bic r12, r12, #0x4 + bic r12, r12, #DLLIDLE_MASK str r12, [r11] @ (no OCP barrier needed) bx lr sdram_in_selfrefresh: ldr r11, omap3_sdrc_power @ read the SDRC_POWER register ldr r12, [r11] @ read the contents of SDRC_POWER mov r9, r12 @ keep a copy of SDRC_POWER bits - orr r12, r12, #0x40 @ enable self refresh on idle req - bic r12, r12, #0x4 @ clear PWDENA + orr r12, r12, #SRFRONIDLEREQ_MASK @ enable self refresh on idle + bic r12, r12, #PWDENA_MASK @ clear PWDENA str r12, [r11] @ write back to SDRC_POWER register ldr r12, [r11] @ posted-write barrier for SDRC +idle_sdrc: ldr r11, omap3_cm_iclken1_core @ read the CM_ICLKEN1_CORE reg ldr r12, [r11] - bic r12, r12, #0x2 @ disable iclk bit for SDRC + bic r12, r12, #EN_SDRC_MASK @ disable iclk bit for SDRC str r12, [r11] wait_sdrc_idle: ldr r11, omap3_cm_idlest1_core ldr r12, [r11] - and r12, r12, #0x2 @ check for SDRC idle - cmp r12, #2 + and r12, r12, #ST_SDRC_MASK @ check for SDRC idle + cmp r12, #ST_SDRC_MASK bne wait_sdrc_idle bx lr configure_core_dpll: @@ -99,36 +149,23 @@ configure_core_dpll: ldr r12, [r11] ldr r10, core_m2_mask_val @ modify m2 for core dpll and r12, r12, r10 - orr r12, r12, r3, lsl #0x1B @ r3 contains the M2 val + orr r12, r12, r3, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT str r12, [r11] ldr r12, [r11] @ posted-write barrier for CM - mov r12, #0x800 @ wait for the clock to stabilise - cmp r3, #2 - bne wait_clk_stable bx lr wait_clk_stable: subs r12, r12, #1 bne wait_clk_stable - nop - nop - nop - nop - nop - nop - nop - nop - nop - nop bx lr enable_sdrc: ldr r11, omap3_cm_iclken1_core ldr r12, [r11] - orr r12, r12, #0x2 @ enable iclk bit for SDRC + orr r12, r12, #EN_SDRC_MASK @ enable iclk bit for SDRC str r12, [r11] wait_sdrc_idle1: ldr r11, omap3_cm_idlest1_core ldr r12, [r11] - and r12, r12, #0x2 + and r12, r12, #ST_SDRC_MASK cmp r12, #0 bne wait_sdrc_idle1 restore_sdrc_power_val: @@ -138,14 +175,14 @@ restore_sdrc_power_val: wait_dll_lock: ldr r11, omap3_sdrc_dlla_status ldr r12, [r11] - and r12, r12, #0x4 - cmp r12, #0x4 + and r12, r12, #LOCKSTATUS_MASK + cmp r12, #LOCKSTATUS_MASK bne wait_dll_lock bx lr wait_dll_unlock: ldr r11, omap3_sdrc_dlla_status ldr r12, [r11] - and r12, r12, #0x4 + and r12, r12, #LOCKSTATUS_MASK cmp r12, #0x0 bne wait_dll_unlock bx lr @@ -156,7 +193,9 @@ configure_sdrc: str r1, [r11] ldr r11, omap3_sdrc_actim_ctrlb str r2, [r11] - ldr r2, [r11] @ posted-write barrier for SDRC + ldr r11, omap3_sdrc_mr_0 + str r6, [r11] + ldr r6, [r11] @ posted-write barrier for SDRC bx lr omap3_sdrc_power: @@ -173,6 +212,8 @@ omap3_sdrc_actim_ctrla: .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_0) omap3_sdrc_actim_ctrlb: .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_0) +omap3_sdrc_mr_0: + .word OMAP34XX_SDRC_REGADDR(SDRC_MR_0) omap3_sdrc_dlla_status: .word OMAP34XX_SDRC_REGADDR(SDRC_DLLA_STATUS) omap3_sdrc_dlla_ctrl: diff --git a/arch/arm/mach-orion5x/addr-map.c b/arch/arm/mach-orion5x/addr-map.c index 6f3f77d031d0..d78731edebb6 100644 --- a/arch/arm/mach-orion5x/addr-map.c +++ b/arch/arm/mach-orion5x/addr-map.c @@ -200,6 +200,6 @@ void __init orion5x_setup_pcie_wa_win(u32 base, u32 size) int __init orion5x_setup_sram_win(void) { - return setup_cpu_win(win_alloc_count, ORION5X_SRAM_PHYS_BASE, + return setup_cpu_win(win_alloc_count++, ORION5X_SRAM_PHYS_BASE, ORION5X_SRAM_SIZE, TARGET_SRAM, ATTR_SRAM, -1); } diff --git a/arch/arm/mach-orion5x/common.c b/arch/arm/mach-orion5x/common.c index eafcc49009ea..f87fa1253803 100644 --- a/arch/arm/mach-orion5x/common.c +++ b/arch/arm/mach-orion5x/common.c @@ -562,7 +562,7 @@ static struct platform_device orion5x_crypto_device = { .resource = orion5x_crypto_res, }; -int __init orion5x_crypto_init(void) +static int __init orion5x_crypto_init(void) { int ret; @@ -697,6 +697,14 @@ void __init orion5x_init(void) } /* + * The 5082/5181l/5182/6082/6082l/6183 have crypto + * while 5180n/5181/5281 don't have crypto. + */ + if ((dev == MV88F5181_DEV_ID && rev >= MV88F5181L_REV_A0) || + dev == MV88F5182_DEV_ID || dev == MV88F6183_DEV_ID) + orion5x_crypto_init(); + + /* * Register watchdog driver */ orion5x_wdt_init(); diff --git a/arch/arm/mach-orion5x/common.h b/arch/arm/mach-orion5x/common.h index de483e83edd7..8f004503c96d 100644 --- a/arch/arm/mach-orion5x/common.h +++ b/arch/arm/mach-orion5x/common.h @@ -38,7 +38,6 @@ void orion5x_spi_init(void); void orion5x_uart0_init(void); void orion5x_uart1_init(void); void orion5x_xor_init(void); -int orion5x_crypto_init(void); /* * PCIe/PCI functions. diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig index f4533f8ff4e8..89c992b8f75b 100644 --- a/arch/arm/mach-pxa/Kconfig +++ b/arch/arm/mach-pxa/Kconfig @@ -401,6 +401,16 @@ config MACH_PALMZ72 Say Y here if you intend to run this kernel on Palm Zire 72 handheld computer. +config MACH_TREO680 + bool "Palm Treo 680" + default y + depends on ARCH_PXA_PALM + select PXA27x + select IWMMXT + help + Say Y here if you intend to run this kernel on Palm Treo 680 + smartphone. + config MACH_PALMLD bool "Palm LifeDrive" default y diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile index d18ffef44b8c..d4c6122a342f 100644 --- a/arch/arm/mach-pxa/Makefile +++ b/arch/arm/mach-pxa/Makefile @@ -62,6 +62,7 @@ obj-$(CONFIG_MACH_PALMT5) += palmt5.o obj-$(CONFIG_MACH_PALMTX) += palmtx.o obj-$(CONFIG_MACH_PALMLD) += palmld.o obj-$(CONFIG_MACH_PALMZ72) += palmz72.o +obj-$(CONFIG_MACH_TREO680) += treo680.o obj-$(CONFIG_ARCH_VIPER) += viper.o ifeq ($(CONFIG_MACH_ZYLONITE),y) diff --git a/arch/arm/mach-pxa/corgi.c b/arch/arm/mach-pxa/corgi.c index 962dda2e154a..5363e1aea3fb 100644 --- a/arch/arm/mach-pxa/corgi.c +++ b/arch/arm/mach-pxa/corgi.c @@ -23,6 +23,7 @@ #include <linux/pm.h> #include <linux/gpio.h> #include <linux/backlight.h> +#include <linux/i2c.h> #include <linux/io.h> #include <linux/spi/spi.h> #include <linux/spi/ads7846.h> @@ -600,6 +601,10 @@ static struct platform_device *devices[] __initdata = { &sharpsl_rom_device, }; +static struct i2c_board_info __initdata corgi_i2c_devices[] = { + { I2C_BOARD_INFO("wm8731", 0x1b) }, +}; + static void corgi_poweroff(void) { if (!machine_is_corgi()) @@ -634,6 +639,7 @@ static void __init corgi_init(void) pxa_set_mci_info(&corgi_mci_platform_data); pxa_set_ficp_info(&corgi_ficp_platform_data); pxa_set_i2c_info(NULL); + i2c_register_board_info(0, ARRAY_AND_SIZE(corgi_i2c_devices)); platform_scoop_config = &corgi_pcmcia_config; diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c index 243e0802b5f4..63b10d9bb1d3 100644 --- a/arch/arm/mach-pxa/em-x270.c +++ b/arch/arm/mach-pxa/em-x270.c @@ -30,6 +30,7 @@ #include <linux/apm-emulation.h> #include <linux/i2c.h> #include <linux/i2c/pca953x.h> +#include <linux/regulator/userspace-consumer.h> #include <media/soc_camera.h> @@ -735,6 +736,7 @@ static struct pxa2xx_spi_chip em_x270_libertas_chip = { .rx_threshold = 1, .tx_threshold = 1, .timeout = 1000, + .gpio_cs = 14, }; static unsigned long em_x270_libertas_pin_config[] = { @@ -803,7 +805,6 @@ static int em_x270_libertas_teardown(struct spi_device *spi) struct libertas_spi_platform_data em_x270_libertas_pdata = { .use_dummy_writes = 1, - .gpio_cs = 14, .setup = em_x270_libertas_setup, .teardown = em_x270_libertas_teardown, }; @@ -838,10 +839,14 @@ static void __init em_x270_init_spi(void) static inline void em_x270_init_spi(void) {} #endif -#if defined(CONFIG_SND_PXA2XX_AC97) || defined(CONFIG_SND_PXA2XX_AC97_MODULE) +#if defined(CONFIG_SND_PXA2XX_LIB_AC97) +static pxa2xx_audio_ops_t em_x270_ac97_info = { + .reset_gpio = 113, +}; + static void __init em_x270_init_ac97(void) { - pxa_set_ac97_info(NULL); + pxa_set_ac97_info(&em_x270_ac97_info); } #else static inline void em_x270_init_ac97(void) {} @@ -1038,6 +1043,52 @@ static void __init em_x270_init_camera(void) static inline void em_x270_init_camera(void) {} #endif +static struct regulator_bulk_data em_x270_gps_consumer_supply = { + .supply = "vcc gps", +}; + +static struct regulator_userspace_consumer_data em_x270_gps_consumer_data = { + .name = "vcc gps", + .num_supplies = 1, + .supplies = &em_x270_gps_consumer_supply, +}; + +static struct platform_device em_x270_gps_userspace_consumer = { + .name = "reg-userspace-consumer", + .id = 0, + .dev = { + .platform_data = &em_x270_gps_consumer_data, + }, +}; + +static struct regulator_bulk_data em_x270_gprs_consumer_supply = { + .supply = "vcc gprs", +}; + +static struct regulator_userspace_consumer_data em_x270_gprs_consumer_data = { + .name = "vcc gprs", + .num_supplies = 1, + .supplies = &em_x270_gprs_consumer_supply +}; + +static struct platform_device em_x270_gprs_userspace_consumer = { + .name = "reg-userspace-consumer", + .id = 1, + .dev = { + .platform_data = &em_x270_gprs_consumer_data, + } +}; + +static struct platform_device *em_x270_userspace_consumers[] = { + &em_x270_gps_userspace_consumer, + &em_x270_gprs_userspace_consumer, +}; + +static void __init em_x270_userspace_consumers_init(void) +{ + platform_add_devices(ARRAY_AND_SIZE(em_x270_userspace_consumers)); +} + /* DA9030 related initializations */ #define REGULATOR_CONSUMER(_name, _dev, _supply) \ static struct regulator_consumer_supply _name##_consumers[] = { \ @@ -1047,11 +1098,11 @@ static inline void em_x270_init_camera(void) {} }, \ } -REGULATOR_CONSUMER(ldo3, NULL, "vcc gps"); +REGULATOR_CONSUMER(ldo3, &em_x270_gps_userspace_consumer.dev, "vcc gps"); REGULATOR_CONSUMER(ldo5, NULL, "vcc cam"); REGULATOR_CONSUMER(ldo10, &pxa_device_mci.dev, "vcc sdio"); REGULATOR_CONSUMER(ldo12, NULL, "vcc usb"); -REGULATOR_CONSUMER(ldo19, NULL, "vcc gprs"); +REGULATOR_CONSUMER(ldo19, &em_x270_gprs_userspace_consumer.dev, "vcc gprs"); #define REGULATOR_INIT(_ldo, _min_uV, _max_uV, _ops_mask) \ static struct regulator_init_data _ldo##_data = { \ @@ -1062,6 +1113,7 @@ REGULATOR_CONSUMER(ldo19, NULL, "vcc gprs"); .enabled = 0, \ }, \ .valid_ops_mask = _ops_mask, \ + .apply_uV = 1, \ }, \ .num_consumer_supplies = ARRAY_SIZE(_ldo##_consumers), \ .consumer_supplies = _ldo##_consumers, \ @@ -1240,6 +1292,7 @@ static void __init em_x270_init(void) em_x270_init_spi(); em_x270_init_i2c(); em_x270_init_camera(); + em_x270_userspace_consumers_init(); } MACHINE_START(EM_X270, "Compulab EM-X270") diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c index 7fff467e84fc..81359d574f88 100644 --- a/arch/arm/mach-pxa/hx4700.c +++ b/arch/arm/mach-pxa/hx4700.c @@ -30,6 +30,7 @@ #include <linux/pwm_backlight.h> #include <linux/regulator/bq24022.h> #include <linux/regulator/machine.h> +#include <linux/regulator/max1586.h> #include <linux/spi/ads7846.h> #include <linux/spi/spi.h> #include <linux/usb/gpio_vbus.h> @@ -775,6 +776,45 @@ static struct platform_device strataflash = { }; /* + * Maxim MAX1587A on PI2C + */ + +static struct regulator_consumer_supply max1587a_consumer = { + .supply = "vcc_core", +}; + +static struct regulator_init_data max1587a_v3_info = { + .constraints = { + .name = "vcc_core range", + .min_uV = 900000, + .max_uV = 1705000, + .always_on = 1, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE, + }, + .num_consumer_supplies = 1, + .consumer_supplies = &max1587a_consumer, +}; + +static struct max1586_subdev_data max1587a_subdev = { + .name = "vcc_core", + .id = MAX1586_V3, + .platform_data = &max1587a_v3_info, +}; + +static struct max1586_platform_data max1587a_info = { + .num_subdevs = 1, + .subdevs = &max1587a_subdev, + .v3_gain = MAX1586_GAIN_R24_3k32, /* 730..1550 mV */ +}; + +static struct i2c_board_info __initdata pi2c_board_info[] = { + { + I2C_BOARD_INFO("max1586", 0x14), + .platform_data = &max1587a_info, + }, +}; + +/* * PCMCIA */ @@ -828,6 +868,7 @@ static void __init hx4700_init(void) pxa_set_ficp_info(&ficp_info); pxa27x_set_i2c_power_info(NULL); pxa_set_i2c_info(NULL); + i2c_register_board_info(1, ARRAY_AND_SIZE(pi2c_board_info)); pxa2xx_set_spi_info(2, &pxa_ssp2_master_info); spi_register_board_info(ARRAY_AND_SIZE(tsc2046_board_info)); diff --git a/arch/arm/mach-pxa/include/mach/palmz72.h b/arch/arm/mach-pxa/include/mach/palmz72.h index 5032307ebf7d..2806ef69ba5a 100644 --- a/arch/arm/mach-pxa/include/mach/palmz72.h +++ b/arch/arm/mach-pxa/include/mach/palmz72.h @@ -21,7 +21,7 @@ /* SD/MMC */ #define GPIO_NR_PALMZ72_SD_DETECT_N 14 #define GPIO_NR_PALMZ72_SD_POWER_N 98 -#define GPIO_NR_PALMZ72_SD_RO 115 +#define GPIO_NR_PALMZ72_SD_RO 115 /* Touchscreen */ #define GPIO_NR_PALMZ72_WM9712_IRQ 27 @@ -31,8 +31,7 @@ /* USB */ #define GPIO_NR_PALMZ72_USB_DETECT_N 15 -#define GPIO_NR_PALMZ72_USB_POWER 95 -#define GPIO_NR_PALMZ72_USB_PULLUP 12 +#define GPIO_NR_PALMZ72_USB_PULLUP 95 /* LCD/Backlight */ #define GPIO_NR_PALMZ72_BL_POWER 20 diff --git a/arch/arm/mach-pxa/include/mach/treo680.h b/arch/arm/mach-pxa/include/mach/treo680.h new file mode 100644 index 000000000000..af443b24d99a --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/treo680.h @@ -0,0 +1,49 @@ +/* + * GPIOs and interrupts for Palm Treo 680 smartphone + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#ifndef _INCLUDE_TREO680_H_ +#define _INCLUDE_TREO680_H_ + +/* GPIOs */ +#define GPIO_NR_TREO680_POWER_DETECT 0 +#define GPIO_NR_TREO680_AMP_EN 27 +#define GPIO_NR_TREO680_KEYB_BL 24 +#define GPIO_NR_TREO680_VIBRATE_EN 44 +#define GPIO_NR_TREO680_GREEN_LED 20 +#define GPIO_NR_TREO680_RED_LED 79 +#define GPIO_NR_TREO680_SD_DETECT_N 113 +#define GPIO_NR_TREO680_SD_READONLY 33 +#define GPIO_NR_TREO680_EP_DETECT_N 116 +#define GPIO_NR_TREO680_SD_POWER 42 +#define GPIO_NR_TREO680_USB_DETECT 1 +#define GPIO_NR_TREO680_USB_PULLUP 114 +#define GPIO_NR_TREO680_GSM_POWER 40 +#define GPIO_NR_TREO680_GSM_RESET 87 +#define GPIO_NR_TREO680_GSM_WAKE 57 +#define GPIO_NR_TREO680_GSM_HOST_WAKE 14 +#define GPIO_NR_TREO680_GSM_TRIGGER 10 +#define GPIO_NR_TREO680_BT_EN 43 +#define GPIO_NR_TREO680_IR_EN 115 +#define GPIO_NR_TREO680_IR_TXD 47 +#define GPIO_NR_TREO680_BL_POWER 38 +#define GPIO_NR_TREO680_LCD_POWER 25 + +/* Various addresses */ +#define TREO680_PHYS_RAM_START 0xa0000000 +#define TREO680_PHYS_IO_START 0x40000000 +#define TREO680_STR_BASE 0xa2000000 + +/* BACKLIGHT */ +#define TREO680_MAX_INTENSITY 254 +#define TREO680_DEFAULT_INTENSITY 160 +#define TREO680_LIMIT_MASK 0x7F +#define TREO680_PRESCALER 63 +#define TREO680_PERIOD_NS 3500 + +#endif diff --git a/arch/arm/mach-pxa/mioa701.c b/arch/arm/mach-pxa/mioa701.c index 4dc8c2ec40a9..2d28132c725b 100644 --- a/arch/arm/mach-pxa/mioa701.c +++ b/arch/arm/mach-pxa/mioa701.c @@ -37,6 +37,7 @@ #include <linux/wm97xx_batt.h> #include <linux/mtd/physmap.h> #include <linux/usb/gpio_vbus.h> +#include <linux/regulator/max1586.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> @@ -717,6 +718,38 @@ static struct wm97xx_batt_info mioa701_battery_data = { }; /* + * Voltage regulation + */ +static struct regulator_consumer_supply max1586_consumers[] = { + { + .supply = "vcc_core", + } +}; + +static struct regulator_init_data max1586_v3_info = { + .constraints = { + .name = "vcc_core range", + .min_uV = 1000000, + .max_uV = 1705000, + .always_on = 1, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE, + }, + .num_consumer_supplies = ARRAY_SIZE(max1586_consumers), + .consumer_supplies = max1586_consumers, +}; + +static struct max1586_subdev_data max1586_subdevs[] = { + { .name = "vcc_core", .id = MAX1586_V3, + .platform_data = &max1586_v3_info }, +}; + +static struct max1586_platform_data max1586_info = { + .subdevs = max1586_subdevs, + .num_subdevs = ARRAY_SIZE(max1586_subdevs), + .v3_gain = MAX1586_GAIN_NO_R24, /* 700..1475 mV */ +}; + +/* * Camera interface */ struct pxacamera_platform_data mioa701_pxacamera_platform_data = { @@ -725,6 +758,13 @@ struct pxacamera_platform_data mioa701_pxacamera_platform_data = { .mclk_10khz = 5000, }; +static struct i2c_board_info __initdata mioa701_pi2c_devices[] = { + { + I2C_BOARD_INFO("max1586", 0x14), + .platform_data = &max1586_info, + }, +}; + static struct soc_camera_link iclink = { .bus_id = 0, /* Must match id in pxa27x_device_camera in device.c */ }; @@ -825,7 +865,9 @@ static void __init mioa701_machine_init(void) platform_add_devices(devices, ARRAY_SIZE(devices)); gsm_init(); + i2c_register_board_info(1, ARRAY_AND_SIZE(mioa701_pi2c_devices)); pxa_set_i2c_info(&i2c_pdata); + pxa27x_set_i2c_power_info(NULL); pxa_set_camera_info(&mioa701_pxacamera_platform_data); i2c_register_board_info(0, ARRAY_AND_SIZE(mioa701_i2c_devices)); } diff --git a/arch/arm/mach-pxa/palmz72.c b/arch/arm/mach-pxa/palmz72.c index b88eb4dd2c84..c3645aa3fa3d 100644 --- a/arch/arm/mach-pxa/palmz72.c +++ b/arch/arm/mach-pxa/palmz72.c @@ -27,7 +27,9 @@ #include <linux/pda_power.h> #include <linux/pwm_backlight.h> #include <linux/gpio.h> +#include <linux/wm97xx_batt.h> #include <linux/power_supply.h> +#include <linux/usb/gpio_vbus.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> @@ -41,6 +43,8 @@ #include <mach/irda.h> #include <mach/pxa27x_keypad.h> #include <mach/udc.h> +#include <mach/palmasoc.h> + #include <mach/pm.h> #include "generic.h" @@ -66,6 +70,8 @@ static unsigned long palmz72_pin_config[] __initdata = { GPIO29_AC97_SDATA_IN_0, GPIO30_AC97_SDATA_OUT, GPIO31_AC97_SYNC, + GPIO89_AC97_SYSCLK, + GPIO113_AC97_nRESET, /* IrDA */ GPIO49_GPIO, /* ir disable */ @@ -77,8 +83,7 @@ static unsigned long palmz72_pin_config[] __initdata = { /* USB */ GPIO15_GPIO, /* usb detect */ - GPIO12_GPIO, /* usb pullup */ - GPIO95_GPIO, /* usb power */ + GPIO95_GPIO, /* usb pullup */ /* Matrix keypad */ GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH, @@ -355,6 +360,22 @@ static struct platform_device palmz72_leds = { }; /****************************************************************************** + * UDC + ******************************************************************************/ +static struct gpio_vbus_mach_info palmz72_udc_info = { + .gpio_vbus = GPIO_NR_PALMZ72_USB_DETECT_N, + .gpio_pullup = GPIO_NR_PALMZ72_USB_PULLUP, +}; + +static struct platform_device palmz72_gpio_vbus = { + .name = "gpio-vbus", + .id = -1, + .dev = { + .platform_data = &palmz72_udc_info, + }, +}; + +/****************************************************************************** * Power supply ******************************************************************************/ static int power_supply_init(struct device *dev) @@ -422,6 +443,31 @@ static struct platform_device power_supply = { }; /****************************************************************************** + * WM97xx battery + ******************************************************************************/ +static struct wm97xx_batt_info wm97xx_batt_pdata = { + .batt_aux = WM97XX_AUX_ID3, + .temp_aux = WM97XX_AUX_ID2, + .charge_gpio = -1, + .max_voltage = PALMZ72_BAT_MAX_VOLTAGE, + .min_voltage = PALMZ72_BAT_MIN_VOLTAGE, + .batt_mult = 1000, + .batt_div = 414, + .temp_mult = 1, + .temp_div = 1, + .batt_tech = POWER_SUPPLY_TECHNOLOGY_LIPO, + .batt_name = "main-batt", +}; + +/****************************************************************************** + * aSoC audio + ******************************************************************************/ +static struct platform_device palmz72_asoc = { + .name = "palm27x-asoc", + .id = -1, +}; + +/****************************************************************************** * Framebuffer ******************************************************************************/ static struct pxafb_mode_info palmz72_lcd_modes[] = { @@ -527,17 +573,32 @@ device_initcall(palmz72_pm_init); static struct platform_device *devices[] __initdata = { &palmz72_backlight, &palmz72_leds, + &palmz72_asoc, &power_supply, + &palmz72_gpio_vbus, }; +/* setup udc GPIOs initial state */ +static void __init palmz72_udc_init(void) +{ + if (!gpio_request(GPIO_NR_PALMZ72_USB_PULLUP, "USB Pullup")) { + gpio_direction_output(GPIO_NR_PALMZ72_USB_PULLUP, 0); + gpio_free(GPIO_NR_PALMZ72_USB_PULLUP); + } +} + static void __init palmz72_init(void) { pxa2xx_mfp_config(ARRAY_AND_SIZE(palmz72_pin_config)); + set_pxa_fb_info(&palmz72_lcd_screen); pxa_set_mci_info(&palmz72_mci_platform_data); + palmz72_udc_init(); pxa_set_ac97_info(NULL); pxa_set_ficp_info(&palmz72_ficp_platform_data); pxa_set_keypad_info(&palmz72_keypad_platform_data); + wm97xx_bat_set_pdata(&wm97xx_batt_pdata); + platform_add_devices(devices, ARRAY_SIZE(devices)); } diff --git a/arch/arm/mach-pxa/poodle.c b/arch/arm/mach-pxa/poodle.c index ac431ed10399..9352d4a34837 100644 --- a/arch/arm/mach-pxa/poodle.c +++ b/arch/arm/mach-pxa/poodle.c @@ -22,6 +22,7 @@ #include <linux/delay.h> #include <linux/mtd/physmap.h> #include <linux/gpio.h> +#include <linux/i2c.h> #include <linux/spi/spi.h> #include <linux/spi/ads7846.h> #include <linux/mtd/sharpsl.h> @@ -486,6 +487,10 @@ static struct platform_device *devices[] __initdata = { &sharpsl_rom_device, }; +static struct i2c_board_info __initdata poodle_i2c_devices[] = { + { I2C_BOARD_INFO("wm8731", 0x1b) }, +}; + static void poodle_poweroff(void) { arm_machine_restart('h', NULL); @@ -519,6 +524,7 @@ static void __init poodle_init(void) pxa_set_mci_info(&poodle_mci_platform_data); pxa_set_ficp_info(&poodle_ficp_platform_data); pxa_set_i2c_info(NULL); + i2c_register_board_info(0, ARRAY_AND_SIZE(poodle_i2c_devices)); poodle_init_spi(); } diff --git a/arch/arm/mach-pxa/treo680.c b/arch/arm/mach-pxa/treo680.c new file mode 100644 index 000000000000..a06f19edebb3 --- /dev/null +++ b/arch/arm/mach-pxa/treo680.c @@ -0,0 +1,612 @@ +/* + * Hardware definitions for Palm Treo 680 + * + * Author: Tomas Cech <sleep_walker@suse.cz> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * (find more info at www.hackndev.com) + * + */ + +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/irq.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> +#include <linux/pda_power.h> +#include <linux/pwm_backlight.h> +#include <linux/gpio.h> +#include <linux/wm97xx_batt.h> +#include <linux/power_supply.h> +#include <linux/sysdev.h> +#include <linux/w1-gpio.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <mach/pxa27x.h> +#include <mach/pxa27x-udc.h> +#include <mach/audio.h> +#include <mach/treo680.h> +#include <mach/mmc.h> +#include <mach/pxafb.h> +#include <mach/irda.h> +#include <mach/pxa27x_keypad.h> +#include <mach/udc.h> +#include <mach/ohci.h> +#include <mach/pxa2xx-regs.h> +#include <mach/palmasoc.h> +#include <mach/camera.h> + +#include <sound/pxa2xx-lib.h> + +#include "generic.h" +#include "devices.h" + +/****************************************************************************** + * Pin configuration + ******************************************************************************/ +static unsigned long treo680_pin_config[] __initdata = { + /* MMC */ + GPIO32_MMC_CLK, + GPIO92_MMC_DAT_0, + GPIO109_MMC_DAT_1, + GPIO110_MMC_DAT_2, + GPIO111_MMC_DAT_3, + GPIO112_MMC_CMD, + GPIO33_GPIO, /* SD read only */ + GPIO113_GPIO, /* SD detect */ + + /* AC97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, + GPIO89_AC97_SYSCLK, + GPIO95_AC97_nRESET, + + /* IrDA */ + GPIO46_FICP_RXD, + GPIO47_FICP_TXD, + + /* PWM */ + GPIO16_PWM0_OUT, + + /* USB */ + GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH, /* usb detect */ + + /* MATRIX KEYPAD */ + GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH, + GPIO101_KP_MKIN_1, + GPIO102_KP_MKIN_2, + GPIO97_KP_MKIN_3, + GPIO98_KP_MKIN_4, + GPIO99_KP_MKIN_5, + GPIO91_KP_MKIN_6, + GPIO13_KP_MKIN_7, + GPIO103_KP_MKOUT_0 | MFP_LPM_DRIVE_HIGH, + GPIO104_KP_MKOUT_1, + GPIO105_KP_MKOUT_2, + GPIO106_KP_MKOUT_3, + GPIO107_KP_MKOUT_4, + GPIO108_KP_MKOUT_5, + GPIO96_KP_MKOUT_6, + GPIO93_KP_DKIN_0 | WAKEUP_ON_LEVEL_HIGH, /* Hotsync button */ + + /* LCD */ + GPIO58_LCD_LDD_0, + GPIO59_LCD_LDD_1, + GPIO60_LCD_LDD_2, + GPIO61_LCD_LDD_3, + GPIO62_LCD_LDD_4, + GPIO63_LCD_LDD_5, + GPIO64_LCD_LDD_6, + GPIO65_LCD_LDD_7, + GPIO66_LCD_LDD_8, + GPIO67_LCD_LDD_9, + GPIO68_LCD_LDD_10, + GPIO69_LCD_LDD_11, + GPIO70_LCD_LDD_12, + GPIO71_LCD_LDD_13, + GPIO72_LCD_LDD_14, + GPIO73_LCD_LDD_15, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, + + /* Quick Capture Interface */ + GPIO84_CIF_FV, + GPIO85_CIF_LV, + GPIO53_CIF_MCLK, + GPIO54_CIF_PCLK, + GPIO81_CIF_DD_0, + GPIO55_CIF_DD_1, + GPIO51_CIF_DD_2, + GPIO50_CIF_DD_3, + GPIO52_CIF_DD_4, + GPIO48_CIF_DD_5, + GPIO17_CIF_DD_6, + GPIO12_CIF_DD_7, + + /* I2C */ + GPIO117_I2C_SCL, + GPIO118_I2C_SDA, + + /* GSM */ + GPIO14_GPIO | WAKEUP_ON_EDGE_BOTH, /* GSM host wake up */ + GPIO34_FFUART_RXD, + GPIO35_FFUART_CTS, + GPIO39_FFUART_TXD, + GPIO41_FFUART_RTS, + + /* MISC. */ + GPIO0_GPIO | WAKEUP_ON_EDGE_BOTH, /* external power detect */ + GPIO15_GPIO | WAKEUP_ON_EDGE_BOTH, /* silent switch */ + GPIO116_GPIO, /* headphone detect */ + GPIO11_GPIO | WAKEUP_ON_EDGE_BOTH, /* bluetooth host wake up */ +}; + +/****************************************************************************** + * SD/MMC card controller + ******************************************************************************/ +static int treo680_mci_init(struct device *dev, + irq_handler_t treo680_detect_int, void *data) +{ + int err = 0; + + /* Setup an interrupt for detecting card insert/remove events */ + err = gpio_request(GPIO_NR_TREO680_SD_DETECT_N, "SD IRQ"); + + if (err) + goto err; + + err = gpio_direction_input(GPIO_NR_TREO680_SD_DETECT_N); + if (err) + goto err2; + + err = request_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N), + treo680_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM | + IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, + "SD/MMC card detect", data); + + if (err) { + dev_err(dev, "%s: cannot request SD/MMC card detect IRQ\n", + __func__); + goto err2; + } + + err = gpio_request(GPIO_NR_TREO680_SD_POWER, "SD_POWER"); + if (err) + goto err3; + + err = gpio_direction_output(GPIO_NR_TREO680_SD_POWER, 1); + if (err) + goto err4; + + err = gpio_request(GPIO_NR_TREO680_SD_READONLY, "SD_READONLY"); + if (err) + goto err4; + + err = gpio_direction_input(GPIO_NR_TREO680_SD_READONLY); + if (err) + goto err5; + + return 0; + +err5: + gpio_free(GPIO_NR_TREO680_SD_READONLY); +err4: + gpio_free(GPIO_NR_TREO680_SD_POWER); +err3: + free_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N), data); +err2: + gpio_free(GPIO_NR_TREO680_SD_DETECT_N); +err: + return err; +} + +static void treo680_mci_exit(struct device *dev, void *data) +{ + gpio_free(GPIO_NR_TREO680_SD_READONLY); + gpio_free(GPIO_NR_TREO680_SD_POWER); + free_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N), data); + gpio_free(GPIO_NR_TREO680_SD_DETECT_N); +} + +static void treo680_mci_power(struct device *dev, unsigned int vdd) +{ + struct pxamci_platform_data *p_d = dev->platform_data; + gpio_set_value(GPIO_NR_TREO680_SD_POWER, p_d->ocr_mask & (1 << vdd)); +} + +static int treo680_mci_get_ro(struct device *dev) +{ + return gpio_get_value(GPIO_NR_TREO680_SD_READONLY); +} + +static struct pxamci_platform_data treo680_mci_platform_data = { + .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, + .setpower = treo680_mci_power, + .get_ro = treo680_mci_get_ro, + .init = treo680_mci_init, + .exit = treo680_mci_exit, +}; + +/****************************************************************************** + * GPIO keyboard + ******************************************************************************/ +static unsigned int treo680_matrix_keys[] = { + KEY(0, 0, KEY_F8), /* Red/Off/Power */ + KEY(0, 1, KEY_LEFT), + KEY(0, 2, KEY_LEFTCTRL), /* Alternate */ + KEY(0, 3, KEY_L), + KEY(0, 4, KEY_A), + KEY(0, 5, KEY_Q), + KEY(0, 6, KEY_P), + + KEY(1, 0, KEY_RIGHTCTRL), /* Menu */ + KEY(1, 1, KEY_RIGHT), + KEY(1, 2, KEY_LEFTSHIFT), /* Left shift */ + KEY(1, 3, KEY_Z), + KEY(1, 4, KEY_S), + KEY(1, 5, KEY_W), + + KEY(2, 0, KEY_F1), /* Phone */ + KEY(2, 1, KEY_UP), + KEY(2, 2, KEY_0), + KEY(2, 3, KEY_X), + KEY(2, 4, KEY_D), + KEY(2, 5, KEY_E), + + KEY(3, 0, KEY_F10), /* Calendar */ + KEY(3, 1, KEY_DOWN), + KEY(3, 2, KEY_SPACE), + KEY(3, 3, KEY_C), + KEY(3, 4, KEY_F), + KEY(3, 5, KEY_R), + + KEY(4, 0, KEY_F12), /* Mail */ + KEY(4, 1, KEY_KPENTER), + KEY(4, 2, KEY_RIGHTALT), /* Alt */ + KEY(4, 3, KEY_V), + KEY(4, 4, KEY_G), + KEY(4, 5, KEY_T), + + KEY(5, 0, KEY_F9), /* Home */ + KEY(5, 1, KEY_PAGEUP), /* Side up */ + KEY(5, 2, KEY_DOT), + KEY(5, 3, KEY_B), + KEY(5, 4, KEY_H), + KEY(5, 5, KEY_Y), + + KEY(6, 0, KEY_TAB), /* Side Activate */ + KEY(6, 1, KEY_PAGEDOWN), /* Side down */ + KEY(6, 2, KEY_ENTER), + KEY(6, 3, KEY_N), + KEY(6, 4, KEY_J), + KEY(6, 5, KEY_U), + + KEY(7, 0, KEY_F6), /* Green/Call */ + KEY(7, 1, KEY_O), + KEY(7, 2, KEY_BACKSPACE), + KEY(7, 3, KEY_M), + KEY(7, 4, KEY_K), + KEY(7, 5, KEY_I), +}; + +static struct pxa27x_keypad_platform_data treo680_keypad_platform_data = { + .matrix_key_rows = 8, + .matrix_key_cols = 7, + .matrix_key_map = treo680_matrix_keys, + .matrix_key_map_size = ARRAY_SIZE(treo680_matrix_keys), + .direct_key_map = { KEY_CONNECT }, + .direct_key_num = 1, + + .debounce_interval = 30, +}; + +/****************************************************************************** + * aSoC audio + ******************************************************************************/ + +static pxa2xx_audio_ops_t treo680_ac97_pdata = { + .reset_gpio = 95, +}; + +/****************************************************************************** + * Backlight + ******************************************************************************/ +static int treo680_backlight_init(struct device *dev) +{ + int ret; + + ret = gpio_request(GPIO_NR_TREO680_BL_POWER, "BL POWER"); + if (ret) + goto err; + ret = gpio_direction_output(GPIO_NR_TREO680_BL_POWER, 0); + if (ret) + goto err2; + ret = gpio_request(GPIO_NR_TREO680_LCD_POWER, "LCD POWER"); + if (ret) + goto err2; + ret = gpio_direction_output(GPIO_NR_TREO680_LCD_POWER, 0); + if (ret) + goto err3; + + return 0; +err3: + gpio_free(GPIO_NR_TREO680_LCD_POWER); +err2: + gpio_free(GPIO_NR_TREO680_BL_POWER); +err: + return ret; +} + +static int treo680_backlight_notify(int brightness) +{ + gpio_set_value(GPIO_NR_TREO680_BL_POWER, brightness); + return TREO680_MAX_INTENSITY - brightness; +}; + +static void treo680_backlight_exit(struct device *dev) +{ + gpio_free(GPIO_NR_TREO680_BL_POWER); + gpio_free(GPIO_NR_TREO680_LCD_POWER); +} + +static struct platform_pwm_backlight_data treo680_backlight_data = { + .pwm_id = 0, + .max_brightness = TREO680_MAX_INTENSITY, + .dft_brightness = TREO680_DEFAULT_INTENSITY, + .pwm_period_ns = TREO680_PERIOD_NS, + .init = treo680_backlight_init, + .notify = treo680_backlight_notify, + .exit = treo680_backlight_exit, +}; + +static struct platform_device treo680_backlight = { + .name = "pwm-backlight", + .dev = { + .parent = &pxa27x_device_pwm0.dev, + .platform_data = &treo680_backlight_data, + }, +}; + +/****************************************************************************** + * IrDA + ******************************************************************************/ +static void treo680_transceiver_mode(struct device *dev, int mode) +{ + gpio_set_value(GPIO_NR_TREO680_IR_EN, mode & IR_OFF); + pxa2xx_transceiver_mode(dev, mode); +} + +static int treo680_irda_startup(struct device *dev) +{ + int err; + + err = gpio_request(GPIO_NR_TREO680_IR_EN, "Ir port disable"); + if (err) + goto err1; + + err = gpio_direction_output(GPIO_NR_TREO680_IR_EN, 1); + if (err) + goto err2; + + return 0; + +err2: + dev_err(dev, "treo680_irda: cannot change IR gpio direction\n"); + gpio_free(GPIO_NR_TREO680_IR_EN); +err1: + dev_err(dev, "treo680_irda: cannot allocate IR gpio\n"); + return err; +} + +static void treo680_irda_shutdown(struct device *dev) +{ + gpio_free(GPIO_NR_TREO680_AMP_EN); +} + +static struct pxaficp_platform_data treo680_ficp_info = { + .transceiver_cap = IR_FIRMODE | IR_SIRMODE | IR_OFF, + .startup = treo680_irda_startup, + .shutdown = treo680_irda_shutdown, + .transceiver_mode = treo680_transceiver_mode, +}; + +/****************************************************************************** + * UDC + ******************************************************************************/ +static struct pxa2xx_udc_mach_info treo680_udc_info __initdata = { + .gpio_vbus = GPIO_NR_TREO680_USB_DETECT, + .gpio_vbus_inverted = 1, + .gpio_pullup = GPIO_NR_TREO680_USB_PULLUP, +}; + + +/****************************************************************************** + * USB host + ******************************************************************************/ +static struct pxaohci_platform_data treo680_ohci_info = { + .port_mode = PMM_PERPORT_MODE, + .flags = ENABLE_PORT1 | ENABLE_PORT3, + .power_budget = 0, +}; + +/****************************************************************************** + * Power supply + ******************************************************************************/ +static int power_supply_init(struct device *dev) +{ + int ret; + + ret = gpio_request(GPIO_NR_TREO680_POWER_DETECT, "CABLE_STATE_AC"); + if (ret) + goto err1; + ret = gpio_direction_input(GPIO_NR_TREO680_POWER_DETECT); + if (ret) + goto err2; + + return 0; + +err2: + gpio_free(GPIO_NR_TREO680_POWER_DETECT); +err1: + return ret; +} + +static int treo680_is_ac_online(void) +{ + return gpio_get_value(GPIO_NR_TREO680_POWER_DETECT); +} + +static void power_supply_exit(struct device *dev) +{ + gpio_free(GPIO_NR_TREO680_POWER_DETECT); +} + +static char *treo680_supplicants[] = { + "main-battery", +}; + +static struct pda_power_pdata power_supply_info = { + .init = power_supply_init, + .is_ac_online = treo680_is_ac_online, + .exit = power_supply_exit, + .supplied_to = treo680_supplicants, + .num_supplicants = ARRAY_SIZE(treo680_supplicants), +}; + +static struct platform_device power_supply = { + .name = "pda-power", + .id = -1, + .dev = { + .platform_data = &power_supply_info, + }, +}; + +/****************************************************************************** + * Vibra and LEDs + ******************************************************************************/ +static struct gpio_led gpio_leds[] = { + { + .name = "treo680:vibra:vibra", + .default_trigger = "none", + .gpio = GPIO_NR_TREO680_VIBRATE_EN, + }, + { + .name = "treo680:green:led", + .default_trigger = "mmc0", + .gpio = GPIO_NR_TREO680_GREEN_LED, + }, + { + .name = "treo680:keybbl:keybbl", + .default_trigger = "none", + .gpio = GPIO_NR_TREO680_KEYB_BL, + }, +}; + +static struct gpio_led_platform_data gpio_led_info = { + .leds = gpio_leds, + .num_leds = ARRAY_SIZE(gpio_leds), +}; + +static struct platform_device treo680_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &gpio_led_info, + } +}; + + +/****************************************************************************** + * Framebuffer + ******************************************************************************/ +/* TODO: add support for 324x324 */ +static struct pxafb_mode_info treo680_lcd_modes[] = { +{ + .pixclock = 86538, + .xres = 320, + .yres = 320, + .bpp = 16, + + .left_margin = 20, + .right_margin = 8, + .upper_margin = 8, + .lower_margin = 5, + + .hsync_len = 4, + .vsync_len = 1, +}, +}; + +static struct pxafb_mach_info treo680_lcd_screen = { + .modes = treo680_lcd_modes, + .num_modes = ARRAY_SIZE(treo680_lcd_modes), + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, +}; + +/****************************************************************************** + * Power management - standby + ******************************************************************************/ +static void __init treo680_pm_init(void) +{ + static u32 resume[] = { + 0xe3a00101, /* mov r0, #0x40000000 */ + 0xe380060f, /* orr r0, r0, #0x00f00000 */ + 0xe590f008, /* ldr pc, [r0, #0x08] */ + }; + + /* this is where the bootloader jumps */ + memcpy(phys_to_virt(TREO680_STR_BASE), resume, sizeof(resume)); +} + +/****************************************************************************** + * Machine init + ******************************************************************************/ +static struct platform_device *devices[] __initdata = { + &treo680_backlight, + &treo680_leds, + &power_supply, +}; + +/* setup udc GPIOs initial state */ +static void __init treo680_udc_init(void) +{ + if (!gpio_request(GPIO_NR_TREO680_USB_PULLUP, "UDC Vbus")) { + gpio_direction_output(GPIO_NR_TREO680_USB_PULLUP, 1); + gpio_free(GPIO_NR_TREO680_USB_PULLUP); + } +} + +static void __init treo680_init(void) +{ + treo680_pm_init(); + pxa2xx_mfp_config(ARRAY_AND_SIZE(treo680_pin_config)); + pxa_set_keypad_info(&treo680_keypad_platform_data); + set_pxa_fb_info(&treo680_lcd_screen); + pxa_set_mci_info(&treo680_mci_platform_data); + treo680_udc_init(); + pxa_set_udc_info(&treo680_udc_info); + pxa_set_ac97_info(&treo680_ac97_pdata); + pxa_set_ficp_info(&treo680_ficp_info); + pxa_set_ohci_info(&treo680_ohci_info); + + platform_add_devices(devices, ARRAY_SIZE(devices)); +} + +MACHINE_START(TREO680, "Palm Treo 680") + .phys_io = TREO680_PHYS_IO_START, + .io_pg_offst = io_p2v(0x40000000), + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa27x_init_irq, + .timer = &pxa_timer, + .init_machine = treo680_init, +MACHINE_END diff --git a/arch/arm/mach-realview/realview_pbx.c b/arch/arm/mach-realview/realview_pbx.c index 1fe294d0bf9d..ede2a57240a3 100644 --- a/arch/arm/mach-realview/realview_pbx.c +++ b/arch/arm/mach-realview/realview_pbx.c @@ -27,6 +27,7 @@ #include <asm/irq.h> #include <asm/leds.h> #include <asm/mach-types.h> +#include <asm/smp_twd.h> #include <asm/hardware/gic.h> #include <asm/hardware/cache-l2x0.h> diff --git a/arch/arm/mach-s3c2410/usb-simtec.c b/arch/arm/mach-s3c2410/usb-simtec.c index 6cd9377ddb82..50e25fc5f8ab 100644 --- a/arch/arm/mach-s3c2410/usb-simtec.c +++ b/arch/arm/mach-s3c2410/usb-simtec.c @@ -22,7 +22,6 @@ #include <linux/timer.h> #include <linux/init.h> #include <linux/device.h> -#include <linux/gpio.h> #include <linux/io.h> #include <asm/mach/arch.h> diff --git a/arch/arm/mach-s3c2440/Kconfig b/arch/arm/mach-s3c2440/Kconfig index 5df73cbf2b40..8cfeaec37306 100644 --- a/arch/arm/mach-s3c2440/Kconfig +++ b/arch/arm/mach-s3c2440/Kconfig @@ -84,5 +84,15 @@ config MACH_AT2440EVB help Say Y here if you are using the AT2440EVB development board +config MACH_MINI2440 + bool "MINI2440 development board" + select CPU_S3C2440 + select EEPROM_AT24 + select LEDS_TRIGGER_BACKLIGHT + select SND_S3C24XX_SOC_S3C24XX_UDA134X + help + Say Y here to select support for the MINI2440. Is a 10cm x 10cm board + available via various sources. It can come with a 3.5" or 7" touch LCD. + endmenu diff --git a/arch/arm/mach-s3c2440/Makefile b/arch/arm/mach-s3c2440/Makefile index 0b4440e79b90..bfadcf684a2a 100644 --- a/arch/arm/mach-s3c2440/Makefile +++ b/arch/arm/mach-s3c2440/Makefile @@ -22,3 +22,4 @@ obj-$(CONFIG_MACH_RX3715) += mach-rx3715.o obj-$(CONFIG_ARCH_S3C2440) += mach-smdk2440.o obj-$(CONFIG_MACH_NEXCODER_2440) += mach-nexcoder.o obj-$(CONFIG_MACH_AT2440EVB) += mach-at2440evb.o +obj-$(CONFIG_MACH_MINI2440) += mach-mini2440.o diff --git a/arch/arm/mach-s3c2440/mach-mini2440.c b/arch/arm/mach-s3c2440/mach-mini2440.c new file mode 100644 index 000000000000..6a5bc3021bdb --- /dev/null +++ b/arch/arm/mach-s3c2440/mach-mini2440.c @@ -0,0 +1,703 @@ +/* linux/arch/arm/mach-s3c2440/mach-mini2440.c + * + * Copyright (c) 2008 Ramax Lo <ramaxlo@gmail.com> + * Based on mach-anubis.c by Ben Dooks <ben@simtec.co.uk> + * and modifications by SBZ <sbz@spgui.org> and + * Weibing <http://weibing.blogbus.com> and + * Michel Pollet <buserror@gmail.com> + * + * For product information, visit http://code.google.com/p/mini2440/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/list.h> +#include <linux/timer.h> +#include <linux/init.h> +#include <linux/gpio.h> +#include <linux/input.h> +#include <linux/io.h> +#include <linux/serial_core.h> +#include <linux/dm9000.h> +#include <linux/i2c/at24.h> +#include <linux/platform_device.h> +#include <linux/gpio_keys.h> +#include <linux/i2c.h> +#include <linux/mmc/host.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <mach/hardware.h> +#include <mach/fb.h> +#include <asm/mach-types.h> + +#include <plat/regs-serial.h> +#include <mach/regs-gpio.h> +#include <mach/leds-gpio.h> +#include <mach/regs-mem.h> +#include <mach/regs-lcd.h> +#include <mach/irqs.h> +#include <plat/nand.h> +#include <plat/iic.h> +#include <plat/mci.h> +#include <plat/udc.h> + +#include <plat/regs-serial.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/partitions.h> + +#include <plat/clock.h> +#include <plat/devs.h> +#include <plat/cpu.h> + +#include <sound/s3c24xx_uda134x.h> + +#define MACH_MINI2440_DM9K_BASE (S3C2410_CS4 + 0x300) + +static struct map_desc mini2440_iodesc[] __initdata = { + /* nothing to declare, move along */ +}; + +#define UCON S3C2410_UCON_DEFAULT +#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB +#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE + + +static struct s3c2410_uartcfg mini2440_uartcfgs[] __initdata = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, + [2] = { + .hwport = 2, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, +}; + +/* USB device UDC support */ + +static void mini2440_udc_pullup(enum s3c2410_udc_cmd_e cmd) +{ + pr_debug("udc: pullup(%d)\n", cmd); + + switch (cmd) { + case S3C2410_UDC_P_ENABLE : + s3c2410_gpio_setpin(S3C2410_GPC(5), 1); + break; + case S3C2410_UDC_P_DISABLE : + s3c2410_gpio_setpin(S3C2410_GPC(5), 0); + break; + case S3C2410_UDC_P_RESET : + break; + default: + break; + } +} + +static struct s3c2410_udc_mach_info mini2440_udc_cfg __initdata = { + .udc_command = mini2440_udc_pullup, +}; + + +/* LCD timing and setup */ + +/* + * This macro simplifies the table bellow + */ +#define _LCD_DECLARE(_clock,_xres,margin_left,margin_right,hsync, \ + _yres,margin_top,margin_bottom,vsync, refresh) \ + .width = _xres, \ + .xres = _xres, \ + .height = _yres, \ + .yres = _yres, \ + .left_margin = margin_left, \ + .right_margin = margin_right, \ + .upper_margin = margin_top, \ + .lower_margin = margin_bottom, \ + .hsync_len = hsync, \ + .vsync_len = vsync, \ + .pixclock = ((_clock*100000000000LL) / \ + ((refresh) * \ + (hsync + margin_left + _xres + margin_right) * \ + (vsync + margin_top + _yres + margin_bottom))), \ + .bpp = 16,\ + .type = (S3C2410_LCDCON1_TFT16BPP |\ + S3C2410_LCDCON1_TFT) + +struct s3c2410fb_display mini2440_lcd_cfg[] __initdata = { + [0] = { /* mini2440 + 3.5" TFT + touchscreen */ + _LCD_DECLARE( + 7, /* The 3.5 is quite fast */ + 240, 21, 38, 6, /* x timing */ + 320, 4, 4, 2, /* y timing */ + 60), /* refresh rate */ + .lcdcon5 = (S3C2410_LCDCON5_FRM565 | + S3C2410_LCDCON5_INVVLINE | + S3C2410_LCDCON5_INVVFRAME | + S3C2410_LCDCON5_INVVDEN | + S3C2410_LCDCON5_PWREN), + }, + [1] = { /* mini2440 + 7" TFT + touchscreen */ + _LCD_DECLARE( + 10, /* the 7" runs slower */ + 800, 40, 40, 48, /* x timing */ + 480, 29, 3, 3, /* y timing */ + 50), /* refresh rate */ + .lcdcon5 = (S3C2410_LCDCON5_FRM565 | + S3C2410_LCDCON5_INVVLINE | + S3C2410_LCDCON5_INVVFRAME | + S3C2410_LCDCON5_PWREN), + }, + /* The VGA shield can outout at several resolutions. All share + * the same timings, however, anything smaller than 1024x768 + * will only be displayed in the top left corner of a 1024x768 + * XGA output unless you add optional dip switches to the shield. + * Therefore timings for other resolutions have been ommited here. + */ + [2] = { + _LCD_DECLARE( + 10, + 1024, 1, 2, 2, /* y timing */ + 768, 200, 16, 16, /* x timing */ + 24), /* refresh rate, maximum stable, + tested with the FPGA shield */ + .lcdcon5 = (S3C2410_LCDCON5_FRM565 | + S3C2410_LCDCON5_HWSWP), + }, +}; + +/* todo - put into gpio header */ + +#define S3C2410_GPCCON_MASK(x) (3 << ((x) * 2)) +#define S3C2410_GPDCON_MASK(x) (3 << ((x) * 2)) + +struct s3c2410fb_mach_info mini2440_fb_info __initdata = { + .displays = &mini2440_lcd_cfg[0], /* not constant! see init */ + .num_displays = 1, + .default_display = 0, + + /* Enable VD[2..7], VD[10..15], VD[18..23] and VCLK, syncs, VDEN + * and disable the pull down resistors on pins we are using for LCD + * data. */ + + .gpcup = (0xf << 1) | (0x3f << 10), + + .gpccon = (S3C2410_GPC1_VCLK | S3C2410_GPC2_VLINE | + S3C2410_GPC3_VFRAME | S3C2410_GPC4_VM | + S3C2410_GPC10_VD2 | S3C2410_GPC11_VD3 | + S3C2410_GPC12_VD4 | S3C2410_GPC13_VD5 | + S3C2410_GPC14_VD6 | S3C2410_GPC15_VD7), + + .gpccon_mask = (S3C2410_GPCCON_MASK(1) | S3C2410_GPCCON_MASK(2) | + S3C2410_GPCCON_MASK(3) | S3C2410_GPCCON_MASK(4) | + S3C2410_GPCCON_MASK(10) | S3C2410_GPCCON_MASK(11) | + S3C2410_GPCCON_MASK(12) | S3C2410_GPCCON_MASK(13) | + S3C2410_GPCCON_MASK(14) | S3C2410_GPCCON_MASK(15)), + + .gpdup = (0x3f << 2) | (0x3f << 10), + + .gpdcon = (S3C2410_GPD2_VD10 | S3C2410_GPD3_VD11 | + S3C2410_GPD4_VD12 | S3C2410_GPD5_VD13 | + S3C2410_GPD6_VD14 | S3C2410_GPD7_VD15 | + S3C2410_GPD10_VD18 | S3C2410_GPD11_VD19 | + S3C2410_GPD12_VD20 | S3C2410_GPD13_VD21 | + S3C2410_GPD14_VD22 | S3C2410_GPD15_VD23), + + .gpdcon_mask = (S3C2410_GPDCON_MASK(2) | S3C2410_GPDCON_MASK(3) | + S3C2410_GPDCON_MASK(4) | S3C2410_GPDCON_MASK(5) | + S3C2410_GPDCON_MASK(6) | S3C2410_GPDCON_MASK(7) | + S3C2410_GPDCON_MASK(10) | S3C2410_GPDCON_MASK(11)| + S3C2410_GPDCON_MASK(12) | S3C2410_GPDCON_MASK(13)| + S3C2410_GPDCON_MASK(14) | S3C2410_GPDCON_MASK(15)), +}; + +/* MMC/SD */ + +static struct s3c24xx_mci_pdata mini2440_mmc_cfg __initdata = { + .gpio_detect = S3C2410_GPG(8), + .gpio_wprotect = S3C2410_GPH(8), + .set_power = NULL, + .ocr_avail = MMC_VDD_32_33|MMC_VDD_33_34, +}; + +/* NAND Flash on MINI2440 board */ + +static struct mtd_partition mini2440_default_nand_part[] __initdata = { + [0] = { + .name = "u-boot", + .size = SZ_256K, + .offset = 0, + }, + [1] = { + .name = "u-boot-env", + .size = SZ_128K, + .offset = SZ_256K, + }, + [2] = { + .name = "kernel", + /* 5 megabytes, for a kernel with no modules + * or a uImage with a ramdisk attached */ + .size = 0x00500000, + .offset = SZ_256K + SZ_128K, + }, + [3] = { + .name = "root", + .offset = SZ_256K + SZ_128K + 0x00500000, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct s3c2410_nand_set mini2440_nand_sets[] __initdata = { + [0] = { + .name = "nand", + .nr_chips = 1, + .nr_partitions = ARRAY_SIZE(mini2440_default_nand_part), + .partitions = mini2440_default_nand_part, + }, +}; + +static struct s3c2410_platform_nand mini2440_nand_info __initdata = { + .tacls = 0, + .twrph0 = 25, + .twrph1 = 15, + .nr_sets = ARRAY_SIZE(mini2440_nand_sets), + .sets = mini2440_nand_sets, + .ignore_unset_ecc = 1, +}; + +/* DM9000AEP 10/100 ethernet controller */ + +static struct resource mini2440_dm9k_resource[] __initdata = { + [0] = { + .start = MACH_MINI2440_DM9K_BASE, + .end = MACH_MINI2440_DM9K_BASE + 3, + .flags = IORESOURCE_MEM + }, + [1] = { + .start = MACH_MINI2440_DM9K_BASE + 4, + .end = MACH_MINI2440_DM9K_BASE + 7, + .flags = IORESOURCE_MEM + }, + [2] = { + .start = IRQ_EINT7, + .end = IRQ_EINT7, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, + } +}; + +/* + * The DM9000 has no eeprom, and it's MAC address is set by + * the bootloader before starting the kernel. + */ +static struct dm9000_plat_data mini2440_dm9k_pdata __initdata = { + .flags = (DM9000_PLATF_16BITONLY | DM9000_PLATF_NO_EEPROM), +}; + +static struct platform_device mini2440_device_eth __initdata = { + .name = "dm9000", + .id = -1, + .num_resources = ARRAY_SIZE(mini2440_dm9k_resource), + .resource = mini2440_dm9k_resource, + .dev = { + .platform_data = &mini2440_dm9k_pdata, + }, +}; + +/* CON5 + * +--+ /-----\ + * | | | | + * | | | BAT | + * | | \_____/ + * | | + * | | +----+ +----+ + * | | | K5 | | K1 | + * | | +----+ +----+ + * | | +----+ +----+ + * | | | K4 | | K2 | + * | | +----+ +----+ + * | | +----+ +----+ + * | | | K6 | | K3 | + * | | +----+ +----+ + * ..... + */ +static struct gpio_keys_button mini2440_buttons[] __initdata = { + { + .gpio = S3C2410_GPG(0), /* K1 */ + .code = KEY_F1, + .desc = "Button 1", + .active_low = 1, + }, + { + .gpio = S3C2410_GPG(3), /* K2 */ + .code = KEY_F2, + .desc = "Button 2", + .active_low = 1, + }, + { + .gpio = S3C2410_GPG(5), /* K3 */ + .code = KEY_F3, + .desc = "Button 3", + .active_low = 1, + }, + { + .gpio = S3C2410_GPG(6), /* K4 */ + .code = KEY_POWER, + .desc = "Power", + .active_low = 1, + }, + { + .gpio = S3C2410_GPG(7), /* K5 */ + .code = KEY_F5, + .desc = "Button 5", + .active_low = 1, + }, +#if 0 + /* this pin is also known as TCLK1 and seems to already + * marked as "in use" somehow in the kernel -- possibly wrongly */ + { + .gpio = S3C2410_GPG(11), /* K6 */ + .code = KEY_F6, + .desc = "Button 6", + .active_low = 1, + }, +#endif +}; + +static struct gpio_keys_platform_data mini2440_button_data __initdata = { + .buttons = mini2440_buttons, + .nbuttons = ARRAY_SIZE(mini2440_buttons), +}; + +static struct platform_device mini2440_button_device __initdata = { + .name = "gpio-keys", + .id = -1, + .dev = { + .platform_data = &mini2440_button_data, + } +}; + +/* LEDS */ + +static struct s3c24xx_led_platdata mini2440_led1_pdata __initdata = { + .name = "led1", + .gpio = S3C2410_GPB(5), + .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, + .def_trigger = "heartbeat", +}; + +static struct s3c24xx_led_platdata mini2440_led2_pdata __initdata = { + .name = "led2", + .gpio = S3C2410_GPB(6), + .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, + .def_trigger = "nand-disk", +}; + +static struct s3c24xx_led_platdata mini2440_led3_pdata __initdata = { + .name = "led3", + .gpio = S3C2410_GPB(7), + .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, + .def_trigger = "mmc0", +}; + +static struct s3c24xx_led_platdata mini2440_led4_pdata __initdata = { + .name = "led4", + .gpio = S3C2410_GPB(8), + .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, + .def_trigger = "", +}; + +static struct s3c24xx_led_platdata mini2440_led_backlight_pdata __initdata = { + .name = "backlight", + .gpio = S3C2410_GPG(4), + .def_trigger = "backlight", +}; + +static struct platform_device mini2440_led1 __initdata = { + .name = "s3c24xx_led", + .id = 1, + .dev = { + .platform_data = &mini2440_led1_pdata, + }, +}; + +static struct platform_device mini2440_led2 __initdata = { + .name = "s3c24xx_led", + .id = 2, + .dev = { + .platform_data = &mini2440_led2_pdata, + }, +}; + +static struct platform_device mini2440_led3 __initdata = { + .name = "s3c24xx_led", + .id = 3, + .dev = { + .platform_data = &mini2440_led3_pdata, + }, +}; + +static struct platform_device mini2440_led4 __initdata = { + .name = "s3c24xx_led", + .id = 4, + .dev = { + .platform_data = &mini2440_led4_pdata, + }, +}; + +static struct platform_device mini2440_led_backlight __initdata = { + .name = "s3c24xx_led", + .id = 5, + .dev = { + .platform_data = &mini2440_led_backlight_pdata, + }, +}; + +/* AUDIO */ + +static struct s3c24xx_uda134x_platform_data mini2440_audio_pins __initdata = { + .l3_clk = S3C2410_GPB(4), + .l3_mode = S3C2410_GPB(2), + .l3_data = S3C2410_GPB(3), + .model = UDA134X_UDA1341 +}; + +static struct platform_device mini2440_audio __initdata = { + .name = "s3c24xx_uda134x", + .id = 0, + .dev = { + .platform_data = &mini2440_audio_pins, + }, +}; + +/* + * I2C devices + */ +static struct at24_platform_data at24c08 = { + .byte_len = SZ_8K / 8, + .page_size = 16, +}; + +static struct i2c_board_info mini2440_i2c_devs[] __initdata = { + { + I2C_BOARD_INFO("24c08", 0x50), + .platform_data = &at24c08, + }, +}; + +static struct platform_device *mini2440_devices[] __initdata = { + &s3c_device_usb, + &s3c_device_wdt, +/* &s3c_device_adc,*/ /* ADC doesn't like living with touchscreen ! */ + &s3c_device_i2c0, + &s3c_device_rtc, + &s3c_device_usbgadget, + &mini2440_device_eth, + &mini2440_led1, + &mini2440_led2, + &mini2440_led3, + &mini2440_led4, + &mini2440_button_device, + &s3c_device_nand, + &s3c_device_sdi, + &s3c_device_iis, + &mini2440_audio, +/* &s3c_device_timer[0],*/ /* buzzer pwm, no API for it */ + /* remaining devices are optional */ +}; + +static void __init mini2440_map_io(void) +{ + s3c24xx_init_io(mini2440_iodesc, ARRAY_SIZE(mini2440_iodesc)); + s3c24xx_init_clocks(12000000); + s3c24xx_init_uarts(mini2440_uartcfgs, ARRAY_SIZE(mini2440_uartcfgs)); + + s3c_device_nand.dev.platform_data = &mini2440_nand_info; + s3c_device_sdi.dev.platform_data = &mini2440_mmc_cfg; +} + +/* + * mini2440_features string + * + * t = Touchscreen present + * b = backlight control + * c = camera [TODO] + * 0-9 LCD configuration + * + */ +static char mini2440_features_str[12] __initdata = "0tb"; + +static int __init mini2440_features_setup(char *str) +{ + if (str) + strlcpy(mini2440_features_str, str, sizeof(mini2440_features_str)); + return 1; +} + +__setup("mini2440=", mini2440_features_setup); + +#define FEATURE_SCREEN (1 << 0) +#define FEATURE_BACKLIGHT (1 << 1) +#define FEATURE_TOUCH (1 << 2) +#define FEATURE_CAMERA (1 << 3) + +struct mini2440_features_t { + int count; + int done; + int lcd_index; + struct platform_device *optional[8]; +}; + +static void mini2440_parse_features( + struct mini2440_features_t * features, + const char * features_str ) +{ + const char * fp = features_str; + + features->count = 0; + features->done = 0; + features->lcd_index = -1; + + while (*fp) { + char f = *fp++; + + switch (f) { + case '0'...'9': /* tft screen */ + if (features->done & FEATURE_SCREEN) { + printk(KERN_INFO "MINI2440: '%c' ignored, " + "screen type already set\n", f); + } else { + int li = f - '0'; + if (li >= ARRAY_SIZE(mini2440_lcd_cfg)) + printk(KERN_INFO "MINI2440: " + "'%c' out of range LCD mode\n", f); + else { + features->optional[features->count++] = + &s3c_device_lcd; + features->lcd_index = li; + } + } + features->done |= FEATURE_SCREEN; + break; + case 'b': + if (features->done & FEATURE_BACKLIGHT) + printk(KERN_INFO "MINI2440: '%c' ignored, " + "backlight already set\n", f); + else { + features->optional[features->count++] = + &mini2440_led_backlight; + } + features->done |= FEATURE_BACKLIGHT; + break; + case 't': + printk(KERN_INFO "MINI2440: '%c' ignored, " + "touchscreen not compiled in\n", f); + break; + case 'c': + if (features->done & FEATURE_CAMERA) + printk(KERN_INFO "MINI2440: '%c' ignored, " + "camera already registered\n", f); + else + features->optional[features->count++] = + &s3c_device_camif; + features->done |= FEATURE_CAMERA; + break; + } + } +} + +static void __init mini2440_init(void) +{ + struct mini2440_features_t features = { 0 }; + int i; + + printk(KERN_INFO "MINI2440: Option string mini2440=%s\n", + mini2440_features_str); + + /* Parse the feature string */ + mini2440_parse_features(&features, mini2440_features_str); + + /* turn LCD on */ + s3c2410_gpio_cfgpin(S3C2410_GPC(0), S3C2410_GPC0_LEND); + + /* Turn the backlight early on */ + s3c2410_gpio_setpin(S3C2410_GPG(4), 1); + s3c2410_gpio_cfgpin(S3C2410_GPG(4), S3C2410_GPIO_OUTPUT); + + /* remove pullup on optional PWM backlight -- unused on 3.5 and 7"s */ + s3c2410_gpio_pullup(S3C2410_GPB(1), 0); + s3c2410_gpio_setpin(S3C2410_GPB(1), 0); + s3c2410_gpio_cfgpin(S3C2410_GPB(1), S3C2410_GPIO_INPUT); + + /* Make sure the D+ pullup pin is output */ + s3c2410_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT); + + /* mark the key as input, without pullups (there is one on the board) */ + for (i = 0; i < ARRAY_SIZE(mini2440_buttons); i++) { + s3c2410_gpio_pullup(mini2440_buttons[i].gpio, 0); + s3c2410_gpio_cfgpin(mini2440_buttons[i].gpio, + S3C2410_GPIO_INPUT); + } + if (features.lcd_index != -1) { + int li; + + mini2440_fb_info.displays = + &mini2440_lcd_cfg[features.lcd_index]; + + printk(KERN_INFO "MINI2440: LCD"); + for (li = 0; li < ARRAY_SIZE(mini2440_lcd_cfg); li++) + if (li == features.lcd_index) + printk(" [%d:%dx%d]", li, + mini2440_lcd_cfg[li].width, + mini2440_lcd_cfg[li].height); + else + printk(" %d:%dx%d", li, + mini2440_lcd_cfg[li].width, + mini2440_lcd_cfg[li].height); + printk("\n"); + s3c24xx_fb_set_platdata(&mini2440_fb_info); + } + s3c24xx_udc_set_platdata(&mini2440_udc_cfg); + s3c_i2c0_set_platdata(NULL); + i2c_register_board_info(0, mini2440_i2c_devs, + ARRAY_SIZE(mini2440_i2c_devs)); + + platform_add_devices(mini2440_devices, ARRAY_SIZE(mini2440_devices)); + + if (features.count) /* the optional features */ + platform_add_devices(features.optional, features.count); + +} + + +MACHINE_START(MINI2440, "MINI2440") + /* Maintainer: Michel Pollet <buserror@gmail.com> */ + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + .map_io = mini2440_map_io, + .init_machine = mini2440_init, + .init_irq = s3c24xx_init_irq, + .timer = &s3c24xx_timer, +MACHINE_END diff --git a/arch/arm/mach-s3c2442/Kconfig b/arch/arm/mach-s3c2442/Kconfig index b289d198020e..103e913f2258 100644 --- a/arch/arm/mach-s3c2442/Kconfig +++ b/arch/arm/mach-s3c2442/Kconfig @@ -24,6 +24,18 @@ config SMDK2440_CPU2442 depends on ARCH_S3C2440 select CPU_S3C2442 +config MACH_NEO1973_GTA02 + bool "Openmoko GTA02 / Freerunner phone" + select CPU_S3C2442 + select MFD_PCF50633 + select PCF50633_GPIO + select I2C + select POWER_SUPPLY + select MACH_NEO1973 + select S3C2410_PWM + help + Say Y here if you are using the Openmoko GTA02 / Freerunner GSM Phone + endmenu diff --git a/arch/arm/mach-s3c2442/Makefile b/arch/arm/mach-s3c2442/Makefile index 2a909c6c5798..2a19113a5769 100644 --- a/arch/arm/mach-s3c2442/Makefile +++ b/arch/arm/mach-s3c2442/Makefile @@ -12,5 +12,7 @@ obj- := obj-$(CONFIG_CPU_S3C2442) += s3c2442.o obj-$(CONFIG_CPU_S3C2442) += clock.o +obj-$(CONFIG_MACH_NEO1973_GTA02) += mach-gta02.o + # Machine support diff --git a/arch/arm/mach-s3c2442/include/mach/gta02.h b/arch/arm/mach-s3c2442/include/mach/gta02.h new file mode 100644 index 000000000000..953331d8d56a --- /dev/null +++ b/arch/arm/mach-s3c2442/include/mach/gta02.h @@ -0,0 +1,84 @@ +#ifndef _GTA02_H +#define _GTA02_H + +#include <mach/regs-gpio.h> + +/* Different hardware revisions, passed in ATAG_REVISION by u-boot */ +#define GTA02v1_SYSTEM_REV 0x00000310 +#define GTA02v2_SYSTEM_REV 0x00000320 +#define GTA02v3_SYSTEM_REV 0x00000330 +#define GTA02v4_SYSTEM_REV 0x00000340 +#define GTA02v5_SYSTEM_REV 0x00000350 +/* since A7 is basically same as A6, we use A6 PCB ID */ +#define GTA02v6_SYSTEM_REV 0x00000360 + +#define GTA02_GPIO_n3DL_GSM S3C2410_GPA(13) /* v1 + v2 + v3 only */ + +#define GTA02_GPIO_PWR_LED1 S3C2410_GPB(0) +#define GTA02_GPIO_PWR_LED2 S3C2410_GPB(1) +#define GTA02_GPIO_AUX_LED S3C2410_GPB(2) +#define GTA02_GPIO_VIBRATOR_ON S3C2410_GPB(3) +#define GTA02_GPIO_MODEM_RST S3C2410_GPB(5) +#define GTA02_GPIO_BT_EN S3C2410_GPB(6) +#define GTA02_GPIO_MODEM_ON S3C2410_GPB(7) +#define GTA02_GPIO_EXTINT8 S3C2410_GPB(8) +#define GTA02_GPIO_USB_PULLUP S3C2410_GPB(9) + +#define GTA02_GPIO_PIO5 S3C2410_GPC(5) /* v3 + v4 only */ + +#define GTA02v3_GPIO_nG1_CS S3C2410_GPD(12) /* v3 + v4 only */ +#define GTA02v3_GPIO_nG2_CS S3C2410_GPD(13) /* v3 + v4 only */ +#define GTA02v5_GPIO_HDQ S3C2410_GPD(14) /* v5 + */ + +#define GTA02_GPIO_nG1_INT S3C2410_GPF(0) +#define GTA02_GPIO_IO1 S3C2410_GPF(1) +#define GTA02_GPIO_PIO_2 S3C2410_GPF(2) /* v2 + v3 + v4 only */ +#define GTA02_GPIO_JACK_INSERT S3C2410_GPF(4) +#define GTA02_GPIO_WLAN_GPIO1 S3C2410_GPF(5) /* v2 + v3 + v4 only */ +#define GTA02_GPIO_AUX_KEY S3C2410_GPF(6) +#define GTA02_GPIO_HOLD_KEY S3C2410_GPF(7) + +#define GTA02_GPIO_3D_IRQ S3C2410_GPG(4) +#define GTA02v2_GPIO_nG2_INT S3C2410_GPG(8) /* v2 + v3 + v4 only */ +#define GTA02v3_GPIO_nUSB_OC S3C2410_GPG(9) /* v3 + v4 only */ +#define GTA02v3_GPIO_nUSB_FLT S3C2410_GPG(10) /* v3 + v4 only */ +#define GTA02v3_GPIO_nGSM_OC S3C2410_GPG(11) /* v3 + v4 only */ + +#define GTA02_GPIO_AMP_SHUT S3C2440_GPJ1 /* v2 + v3 + v4 only */ +#define GTA02v1_GPIO_WLAN_GPIO10 S3C2440_GPJ2 +#define GTA02_GPIO_HP_IN S3C2440_GPJ2 /* v2 + v3 + v4 only */ +#define GTA02_GPIO_INT0 S3C2440_GPJ3 /* v2 + v3 + v4 only */ +#define GTA02_GPIO_nGSM_EN S3C2440_GPJ4 +#define GTA02_GPIO_3D_RESET S3C2440_GPJ5 +#define GTA02_GPIO_nDL_GSM S3C2440_GPJ6 /* v4 + v5 only */ +#define GTA02_GPIO_WLAN_GPIO0 S3C2440_GPJ7 +#define GTA02v1_GPIO_BAT_ID S3C2440_GPJ8 +#define GTA02_GPIO_KEEPACT S3C2440_GPJ8 +#define GTA02v1_GPIO_HP_IN S3C2440_GPJ10 +#define GTA02_CHIP_PWD S3C2440_GPJ11 /* v2 + v3 + v4 only */ +#define GTA02_GPIO_nWLAN_RESET S3C2440_GPJ12 /* v2 + v3 + v4 only */ + +#define GTA02_IRQ_GSENSOR_1 IRQ_EINT0 +#define GTA02_IRQ_MODEM IRQ_EINT1 +#define GTA02_IRQ_PIO_2 IRQ_EINT2 /* v2 + v3 + v4 only */ +#define GTA02_IRQ_nJACK_INSERT IRQ_EINT4 +#define GTA02_IRQ_WLAN_GPIO1 IRQ_EINT5 +#define GTA02_IRQ_AUX IRQ_EINT6 +#define GTA02_IRQ_nHOLD IRQ_EINT7 +#define GTA02_IRQ_PCF50633 IRQ_EINT9 +#define GTA02_IRQ_3D IRQ_EINT12 +#define GTA02_IRQ_GSENSOR_2 IRQ_EINT16 /* v2 + v3 + v4 only */ +#define GTA02v3_IRQ_nUSB_OC IRQ_EINT17 /* v3 + v4 only */ +#define GTA02v3_IRQ_nUSB_FLT IRQ_EINT18 /* v3 + v4 only */ +#define GTA02v3_IRQ_nGSM_OC IRQ_EINT19 /* v3 + v4 only */ + +/* returns 00 000 on GTA02 A5 and earlier, A6 returns 01 001 */ +#define GTA02_PCB_ID1_0 S3C2410_GPC(13) +#define GTA02_PCB_ID1_1 S3C2410_GPC(15) +#define GTA02_PCB_ID1_2 S3C2410_GPD(0) +#define GTA02_PCB_ID2_0 S3C2410_GPD(3) +#define GTA02_PCB_ID2_1 S3C2410_GPD(4) + +int gta02_get_pcb_revision(void); + +#endif /* _GTA02_H */ diff --git a/arch/arm/mach-s3c2442/mach-gta02.c b/arch/arm/mach-s3c2442/mach-gta02.c new file mode 100644 index 000000000000..e23b581aa0e1 --- /dev/null +++ b/arch/arm/mach-s3c2442/mach-gta02.c @@ -0,0 +1,646 @@ +/* + * linux/arch/arm/mach-s3c2442/mach-gta02.c + * + * S3C2442 Machine Support for Openmoko GTA02 / FreeRunner. + * + * Copyright (C) 2006-2009 by Openmoko, Inc. + * Authors: Harald Welte <laforge@openmoko.org> + * Andy Green <andy@openmoko.org> + * Werner Almesberger <werner@openmoko.org> + * All rights reserved. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/list.h> +#include <linux/delay.h> +#include <linux/timer.h> +#include <linux/init.h> +#include <linux/gpio.h> +#include <linux/workqueue.h> +#include <linux/platform_device.h> +#include <linux/serial_core.h> +#include <linux/spi/spi.h> + +#include <linux/mmc/host.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> +#include <linux/io.h> + +#include <linux/i2c.h> +#include <linux/backlight.h> +#include <linux/regulator/machine.h> + +#include <linux/mfd/pcf50633/core.h> +#include <linux/mfd/pcf50633/mbc.h> +#include <linux/mfd/pcf50633/adc.h> +#include <linux/mfd/pcf50633/gpio.h> +#include <linux/mfd/pcf50633/pmic.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/irq.h> +#include <asm/mach-types.h> + +#include <mach/regs-irq.h> +#include <mach/regs-gpio.h> +#include <mach/regs-gpioj.h> +#include <mach/fb.h> + +#include <mach/spi.h> +#include <mach/spi-gpio.h> +#include <plat/usb-control.h> +#include <mach/regs-mem.h> +#include <mach/hardware.h> + +#include <mach/gta02.h> + +#include <plat/regs-serial.h> +#include <plat/nand.h> +#include <plat/devs.h> +#include <plat/cpu.h> +#include <plat/pm.h> +#include <plat/udc.h> +#include <plat/gpio-cfg.h> +#include <plat/iic.h> + +static struct pcf50633 *gta02_pcf; + +/* + * This gets called every 1ms when we paniced. + */ + +static long gta02_panic_blink(long count) +{ + long delay = 0; + static long last_blink; + static char led; + + /* Fast blink: 200ms period. */ + if (count - last_blink < 100) + return 0; + + led ^= 1; + gpio_direction_output(GTA02_GPIO_AUX_LED, led); + + last_blink = count; + + return delay; +} + + +static struct map_desc gta02_iodesc[] __initdata = { + { + .virtual = 0xe0000000, + .pfn = __phys_to_pfn(S3C2410_CS3 + 0x01000000), + .length = SZ_1M, + .type = MT_DEVICE + }, +}; + +#define UCON (S3C2410_UCON_DEFAULT | S3C2443_UCON_RXERR_IRQEN) +#define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB) +#define UFCON (S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE) + +static struct s3c2410_uartcfg gta02_uartcfgs[] = { + [0] = { + .hwport = 0, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, + [1] = { + .hwport = 1, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, + [2] = { + .hwport = 2, + .flags = 0, + .ucon = UCON, + .ulcon = ULCON, + .ufcon = UFCON, + }, +}; + +#ifdef CONFIG_CHARGER_PCF50633 +/* + * On GTA02 the 1A charger features a 48K resistor to 0V on the ID pin. + * We use this to recognize that we can pull 1A from the USB socket. + * + * These constants are the measured pcf50633 ADC levels with the 1A + * charger / 48K resistor, and with no pulldown resistor. + */ + +#define ADC_NOM_CHG_DETECT_1A 6 +#define ADC_NOM_CHG_DETECT_USB 43 + +static void +gta02_configure_pmu_for_charger(struct pcf50633 *pcf, void *unused, int res) +{ + int ma; + + /* Interpret charger type */ + if (res < ((ADC_NOM_CHG_DETECT_USB + ADC_NOM_CHG_DETECT_1A) / 2)) { + + /* + * Sanity - stop GPO driving out now that we have a 1A charger + * GPO controls USB Host power generation on GTA02 + */ + pcf50633_gpio_set(pcf, PCF50633_GPO, 0); + + ma = 1000; + } else + ma = 100; + + pcf50633_mbc_usb_curlim_set(pcf, ma); +} + +static struct delayed_work gta02_charger_work; +static int gta02_usb_vbus_draw; + +static void gta02_charger_worker(struct work_struct *work) +{ + if (gta02_usb_vbus_draw) { + pcf50633_mbc_usb_curlim_set(gta02_pcf, gta02_usb_vbus_draw); + return; + } + +#ifdef CONFIG_PCF50633_ADC + pcf50633_adc_async_read(gta02_pcf, + PCF50633_ADCC1_MUX_ADCIN1, + PCF50633_ADCC1_AVERAGE_16, + gta02_configure_pmu_for_charger, + NULL); +#else + /* + * If the PCF50633 ADC is disabled we fallback to a + * 100mA limit for safety. + */ + pcf50633_mbc_usb_curlim_set(pcf, 100); +#endif +} + +#define GTA02_CHARGER_CONFIGURE_TIMEOUT ((3000 * HZ) / 1000) + +static void gta02_pmu_event_callback(struct pcf50633 *pcf, int irq) +{ + if (irq == PCF50633_IRQ_USBINS) { + schedule_delayed_work(>a02_charger_work, + GTA02_CHARGER_CONFIGURE_TIMEOUT); + + return; + } + + if (irq == PCF50633_IRQ_USBREM) { + cancel_delayed_work_sync(>a02_charger_work); + gta02_usb_vbus_draw = 0; + } +} + +static void gta02_udc_vbus_draw(unsigned int ma) +{ + if (!gta02_pcf) + return; + + gta02_usb_vbus_draw = ma; + + schedule_delayed_work(>a02_charger_work, + GTA02_CHARGER_CONFIGURE_TIMEOUT); +} +#else /* !CONFIG_CHARGER_PCF50633 */ +#define gta02_pmu_event_callback NULL +#define gta02_udc_vbus_draw NULL +#endif + +/* + * This is called when pc50633 is probed, unfortunately quite late in the + * day since it is an I2C bus device. Here we can belatedly define some + * platform devices with the advantage that we can mark the pcf50633 as the + * parent. This makes them get suspended and resumed with their parent + * the pcf50633 still around. + */ + +static void gta02_pmu_attach_child_devices(struct pcf50633 *pcf); + + +static char *gta02_batteries[] = { + "battery", +}; + +struct pcf50633_platform_data gta02_pcf_pdata = { + .resumers = { + [0] = PCF50633_INT1_USBINS | + PCF50633_INT1_USBREM | + PCF50633_INT1_ALARM, + [1] = PCF50633_INT2_ONKEYF, + [2] = PCF50633_INT3_ONKEY1S, + [3] = PCF50633_INT4_LOWSYS | + PCF50633_INT4_LOWBAT | + PCF50633_INT4_HIGHTMP, + }, + + .batteries = gta02_batteries, + .num_batteries = ARRAY_SIZE(gta02_batteries), + .reg_init_data = { + [PCF50633_REGULATOR_AUTO] = { + .constraints = { + .min_uV = 3300000, + .max_uV = 3300000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .always_on = 1, + .apply_uV = 1, + .state_mem = { + .enabled = 1, + }, + }, + }, + [PCF50633_REGULATOR_DOWN1] = { + .constraints = { + .min_uV = 1300000, + .max_uV = 1600000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .always_on = 1, + .apply_uV = 1, + }, + }, + [PCF50633_REGULATOR_DOWN2] = { + .constraints = { + .min_uV = 1800000, + .max_uV = 1800000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .apply_uV = 1, + .always_on = 1, + .state_mem = { + .enabled = 1, + }, + }, + }, + [PCF50633_REGULATOR_HCLDO] = { + .constraints = { + .min_uV = 2000000, + .max_uV = 3300000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE, + .always_on = 1, + }, + }, + [PCF50633_REGULATOR_LDO1] = { + .constraints = { + .min_uV = 3300000, + .max_uV = 3300000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .apply_uV = 1, + .state_mem = { + .enabled = 0, + }, + }, + }, + [PCF50633_REGULATOR_LDO2] = { + .constraints = { + .min_uV = 3300000, + .max_uV = 3300000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .apply_uV = 1, + }, + }, + [PCF50633_REGULATOR_LDO3] = { + .constraints = { + .min_uV = 3000000, + .max_uV = 3000000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .apply_uV = 1, + }, + }, + [PCF50633_REGULATOR_LDO4] = { + .constraints = { + .min_uV = 3200000, + .max_uV = 3200000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .apply_uV = 1, + }, + }, + [PCF50633_REGULATOR_LDO5] = { + .constraints = { + .min_uV = 3000000, + .max_uV = 3000000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .apply_uV = 1, + .state_mem = { + .enabled = 1, + }, + }, + }, + [PCF50633_REGULATOR_LDO6] = { + .constraints = { + .min_uV = 3000000, + .max_uV = 3000000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + }, + }, + [PCF50633_REGULATOR_MEMLDO] = { + .constraints = { + .min_uV = 1800000, + .max_uV = 1800000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .state_mem = { + .enabled = 1, + }, + }, + }, + + }, + .probe_done = gta02_pmu_attach_child_devices, + .mbc_event_callback = gta02_pmu_event_callback, +}; + + +/* NOR Flash. */ + +#define GTA02_FLASH_BASE 0x18000000 /* GCS3 */ +#define GTA02_FLASH_SIZE 0x200000 /* 2MBytes */ + +static struct physmap_flash_data gta02_nor_flash_data = { + .width = 2, +}; + +static struct resource gta02_nor_flash_resource = { + .start = GTA02_FLASH_BASE, + .end = GTA02_FLASH_BASE + GTA02_FLASH_SIZE - 1, + .flags = IORESOURCE_MEM, +}; + +static struct platform_device gta02_nor_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = >a02_nor_flash_data, + }, + .resource = >a02_nor_flash_resource, + .num_resources = 1, +}; + + +struct platform_device s3c24xx_pwm_device = { + .name = "s3c24xx_pwm", + .num_resources = 0, +}; + +static struct i2c_board_info gta02_i2c_devs[] __initdata = { + { + I2C_BOARD_INFO("pcf50633", 0x73), + .irq = GTA02_IRQ_PCF50633, + .platform_data = >a02_pcf_pdata, + }, + { + I2C_BOARD_INFO("wm8753", 0x1a), + }, +}; + +static struct s3c2410_nand_set gta02_nand_sets[] = { + [0] = { + /* + * This name is also hard-coded in the boot loaders, so + * changing it would would require all users to upgrade + * their boot loaders, some of which are stored in a NOR + * that is considered to be immutable. + */ + .name = "neo1973-nand", + .nr_chips = 1, + .use_bbt = 1, + .force_soft_ecc = 1, + }, +}; + +/* + * Choose a set of timings derived from S3C@2442B MCP54 + * data sheet (K5D2G13ACM-D075 MCP Memory). + */ + +static struct s3c2410_platform_nand gta02_nand_info = { + .tacls = 0, + .twrph0 = 25, + .twrph1 = 15, + .nr_sets = ARRAY_SIZE(gta02_nand_sets), + .sets = gta02_nand_sets, +}; + + +static void gta02_udc_command(enum s3c2410_udc_cmd_e cmd) +{ + switch (cmd) { + case S3C2410_UDC_P_ENABLE: + pr_debug("%s S3C2410_UDC_P_ENABLE\n", __func__); + gpio_direction_output(GTA02_GPIO_USB_PULLUP, 1); + break; + case S3C2410_UDC_P_DISABLE: + pr_debug("%s S3C2410_UDC_P_DISABLE\n", __func__); + gpio_direction_output(GTA02_GPIO_USB_PULLUP, 0); + break; + case S3C2410_UDC_P_RESET: + pr_debug("%s S3C2410_UDC_P_RESET\n", __func__); + /* FIXME: Do something here. */ + } +} + +/* Get PMU to set USB current limit accordingly. */ +static struct s3c2410_udc_mach_info gta02_udc_cfg = { + .vbus_draw = gta02_udc_vbus_draw, + .udc_command = gta02_udc_command, + +}; + + + +static void gta02_bl_set_intensity(int intensity) +{ + struct pcf50633 *pcf = gta02_pcf; + int old_intensity = pcf50633_reg_read(pcf, PCF50633_REG_LEDOUT); + + /* We map 8-bit intensity to 6-bit intensity in hardware. */ + intensity >>= 2; + + /* + * This can happen during, eg, print of panic on blanked console, + * but we can't service i2c without interrupts active, so abort. + */ + if (in_atomic()) { + printk(KERN_ERR "gta02_bl_set_intensity called while atomic\n"); + return; + } + + old_intensity = pcf50633_reg_read(pcf, PCF50633_REG_LEDOUT); + if (intensity == old_intensity) + return; + + /* We can't do this anywhere else. */ + pcf50633_reg_write(pcf, PCF50633_REG_LEDDIM, 5); + + if (!(pcf50633_reg_read(pcf, PCF50633_REG_LEDENA) & 3)) + old_intensity = 0; + + /* + * The PCF50633 cannot handle LEDOUT = 0 (datasheet p60) + * if seen, you have to re-enable the LED unit. + */ + if (!intensity || !old_intensity) + pcf50633_reg_write(pcf, PCF50633_REG_LEDENA, 0); + + /* Illegal to set LEDOUT to 0. */ + if (!intensity) + pcf50633_reg_set_bit_mask(pcf, PCF50633_REG_LEDOUT, 0x3f, 2); + else + pcf50633_reg_set_bit_mask(pcf, PCF50633_REG_LEDOUT, 0x3f, + intensity); + + if (intensity) + pcf50633_reg_write(pcf, PCF50633_REG_LEDENA, 2); + +} + +static struct generic_bl_info gta02_bl_info = { + .name = "gta02-bl", + .max_intensity = 0xff, + .default_intensity = 0xff, + .set_bl_intensity = gta02_bl_set_intensity, +}; + +static struct platform_device gta02_bl_dev = { + .name = "generic-bl", + .id = 1, + .dev = { + .platform_data = >a02_bl_info, + }, +}; + + + +/* USB */ +static struct s3c2410_hcd_info gta02_usb_info = { + .port[0] = { + .flags = S3C_HCDFLG_USED, + }, + .port[1] = { + .flags = 0, + }, +}; + + +static void __init gta02_map_io(void) +{ + s3c24xx_init_io(gta02_iodesc, ARRAY_SIZE(gta02_iodesc)); + s3c24xx_init_clocks(12000000); + s3c24xx_init_uarts(gta02_uartcfgs, ARRAY_SIZE(gta02_uartcfgs)); +} + + +/* These are the guys that don't need to be children of PMU. */ + +static struct platform_device *gta02_devices[] __initdata = { + &s3c_device_usb, + &s3c_device_wdt, + &s3c_device_sdi, + &s3c_device_usbgadget, + &s3c_device_nand, + >a02_nor_flash, + &s3c24xx_pwm_device, + &s3c_device_iis, + &s3c_device_i2c0, +}; + +/* These guys DO need to be children of PMU. */ + +static struct platform_device *gta02_devices_pmu_children[] = { + >a02_bl_dev, +}; + + +/* + * This is called when pc50633 is probed, quite late in the day since it is an + * I2C bus device. Here we can define platform devices with the advantage that + * we can mark the pcf50633 as the parent. This makes them get suspended and + * resumed with their parent the pcf50633 still around. All devices whose + * operation depends on something from pcf50633 must have this relationship + * made explicit like this, or suspend and resume will become an unreliable + * hellworld. + */ + +static void gta02_pmu_attach_child_devices(struct pcf50633 *pcf) +{ + int n; + + /* Grab a copy of the now probed PMU pointer. */ + gta02_pcf = pcf; + + for (n = 0; n < ARRAY_SIZE(gta02_devices_pmu_children); n++) + gta02_devices_pmu_children[n]->dev.parent = pcf->dev; + + platform_add_devices(gta02_devices_pmu_children, + ARRAY_SIZE(gta02_devices_pmu_children)); +} + +static void gta02_poweroff(void) +{ + pcf50633_reg_set_bit_mask(gta02_pcf, PCF50633_REG_OOCSHDWN, 1, 1); +} + +static void __init gta02_machine_init(void) +{ + /* Set the panic callback to make AUX LED blink at ~5Hz. */ + panic_blink = gta02_panic_blink; + + s3c_pm_init(); + +#ifdef CONFIG_CHARGER_PCF50633 + INIT_DELAYED_WORK(>a02_charger_work, gta02_charger_worker); +#endif + + s3c_device_usb.dev.platform_data = >a02_usb_info; + s3c_device_nand.dev.platform_data = >a02_nand_info; + + s3c24xx_udc_set_platdata(>a02_udc_cfg); + s3c_i2c0_set_platdata(NULL); + + i2c_register_board_info(0, gta02_i2c_devs, ARRAY_SIZE(gta02_i2c_devs)); + + platform_add_devices(gta02_devices, ARRAY_SIZE(gta02_devices)); + pm_power_off = gta02_poweroff; +} + + +MACHINE_START(NEO1973_GTA02, "GTA02") + /* Maintainer: Nelson Castillo <arhuaco@freaks-unidos.net> */ + .phys_io = S3C2410_PA_UART, + .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, + .boot_params = S3C2410_SDRAM_PA + 0x100, + .map_io = gta02_map_io, + .init_irq = s3c24xx_init_irq, + .init_machine = gta02_machine_init, + .timer = &s3c24xx_timer, +MACHINE_END diff --git a/arch/arm/mm/alignment.c b/arch/arm/mm/alignment.c index 3a398befed41..03cd27d917b9 100644 --- a/arch/arm/mm/alignment.c +++ b/arch/arm/mm/alignment.c @@ -62,6 +62,12 @@ #define SHIFT_ASR 0x40 #define SHIFT_RORRRX 0x60 +#define BAD_INSTR 0xdeadc0de + +/* Thumb-2 32 bit format per ARMv7 DDI0406A A6.3, either f800h,e800h,f800h */ +#define IS_T32(hi16) \ + (((hi16) & 0xe000) == 0xe000 && ((hi16) & 0x1800)) + static unsigned long ai_user; static unsigned long ai_sys; static unsigned long ai_skipped; @@ -332,38 +338,48 @@ do_alignment_ldrdstrd(unsigned long addr, unsigned long instr, struct pt_regs *regs) { unsigned int rd = RD_BITS(instr); - - if (((rd & 1) == 1) || (rd == 14)) + unsigned int rd2; + int load; + + if ((instr & 0xfe000000) == 0xe8000000) { + /* ARMv7 Thumb-2 32-bit LDRD/STRD */ + rd2 = (instr >> 8) & 0xf; + load = !!(LDST_L_BIT(instr)); + } else if (((rd & 1) == 1) || (rd == 14)) goto bad; + else { + load = ((instr & 0xf0) == 0xd0); + rd2 = rd + 1; + } ai_dword += 1; if (user_mode(regs)) goto user; - if ((instr & 0xf0) == 0xd0) { + if (load) { unsigned long val; get32_unaligned_check(val, addr); regs->uregs[rd] = val; get32_unaligned_check(val, addr + 4); - regs->uregs[rd + 1] = val; + regs->uregs[rd2] = val; } else { put32_unaligned_check(regs->uregs[rd], addr); - put32_unaligned_check(regs->uregs[rd + 1], addr + 4); + put32_unaligned_check(regs->uregs[rd2], addr + 4); } return TYPE_LDST; user: - if ((instr & 0xf0) == 0xd0) { + if (load) { unsigned long val; get32t_unaligned_check(val, addr); regs->uregs[rd] = val; get32t_unaligned_check(val, addr + 4); - regs->uregs[rd + 1] = val; + regs->uregs[rd2] = val; } else { put32t_unaligned_check(regs->uregs[rd], addr); - put32t_unaligned_check(regs->uregs[rd + 1], addr + 4); + put32t_unaligned_check(regs->uregs[rd2], addr + 4); } return TYPE_LDST; @@ -616,8 +632,72 @@ thumb2arm(u16 tinstr) /* Else fall through for illegal instruction case */ default: - return 0xdeadc0de; + return BAD_INSTR; + } +} + +/* + * Convert Thumb-2 32 bit LDM, STM, LDRD, STRD to equivalent instruction + * handlable by ARM alignment handler, also find the corresponding handler, + * so that we can reuse ARM userland alignment fault fixups for Thumb. + * + * @pinstr: original Thumb-2 instruction; returns new handlable instruction + * @regs: register context. + * @poffset: return offset from faulted addr for later writeback + * + * NOTES: + * 1. Comments below refer to ARMv7 DDI0406A Thumb Instruction sections. + * 2. Register name Rt from ARMv7 is same as Rd from ARMv6 (Rd is Rt) + */ +static void * +do_alignment_t32_to_handler(unsigned long *pinstr, struct pt_regs *regs, + union offset_union *poffset) +{ + unsigned long instr = *pinstr; + u16 tinst1 = (instr >> 16) & 0xffff; + u16 tinst2 = instr & 0xffff; + poffset->un = 0; + + switch (tinst1 & 0xffe0) { + /* A6.3.5 Load/Store multiple */ + case 0xe880: /* STM/STMIA/STMEA,LDM/LDMIA, PUSH/POP T2 */ + case 0xe8a0: /* ...above writeback version */ + case 0xe900: /* STMDB/STMFD, LDMDB/LDMEA */ + case 0xe920: /* ...above writeback version */ + /* no need offset decision since handler calculates it */ + return do_alignment_ldmstm; + + case 0xf840: /* POP/PUSH T3 (single register) */ + if (RN_BITS(instr) == 13 && (tinst2 & 0x09ff) == 0x0904) { + u32 L = !!(LDST_L_BIT(instr)); + const u32 subset[2] = { + 0xe92d0000, /* STMDB sp!,{registers} */ + 0xe8bd0000, /* LDMIA sp!,{registers} */ + }; + *pinstr = subset[L] | (1<<RD_BITS(instr)); + return do_alignment_ldmstm; + } + /* Else fall through for illegal instruction case */ + break; + + /* A6.3.6 Load/store double, STRD/LDRD(immed, lit, reg) */ + case 0xe860: + case 0xe960: + case 0xe8e0: + case 0xe9e0: + poffset->un = (tinst2 & 0xff) << 2; + case 0xe940: + case 0xe9c0: + return do_alignment_ldrdstrd; + + /* + * No need to handle load/store instructions up to word size + * since ARMv6 and later CPUs can perform unaligned accesses. + */ + default: + break; } + return NULL; } static int @@ -630,6 +710,8 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs) mm_segment_t fs; unsigned int fault; u16 tinstr = 0; + int isize = 4; + int thumb2_32b = 0; instrptr = instruction_pointer(regs); @@ -637,8 +719,19 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs) set_fs(KERNEL_DS); if (thumb_mode(regs)) { fault = __get_user(tinstr, (u16 *)(instrptr & ~1)); - if (!(fault)) - instr = thumb2arm(tinstr); + if (!fault) { + if (cpu_architecture() >= CPU_ARCH_ARMv7 && + IS_T32(tinstr)) { + /* Thumb-2 32-bit */ + u16 tinst2 = 0; + fault = __get_user(tinst2, (u16 *)(instrptr+2)); + instr = (tinstr << 16) | tinst2; + thumb2_32b = 1; + } else { + isize = 2; + instr = thumb2arm(tinstr); + } + } } else fault = __get_user(instr, (u32 *)instrptr); set_fs(fs); @@ -655,7 +748,7 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs) fixup: - regs->ARM_pc += thumb_mode(regs) ? 2 : 4; + regs->ARM_pc += isize; switch (CODING_BITS(instr)) { case 0x00000000: /* 3.13.4 load/store instruction extensions */ @@ -714,18 +807,25 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs) handler = do_alignment_ldrstr; break; - case 0x08000000: /* ldm or stm */ - handler = do_alignment_ldmstm; + case 0x08000000: /* ldm or stm, or thumb-2 32bit instruction */ + if (thumb2_32b) + handler = do_alignment_t32_to_handler(&instr, regs, &offset); + else + handler = do_alignment_ldmstm; break; default: goto bad; } + if (!handler) + goto bad; type = handler(addr, instr, regs); - if (type == TYPE_ERROR || type == TYPE_FAULT) + if (type == TYPE_ERROR || type == TYPE_FAULT) { + regs->ARM_pc -= isize; goto bad_or_fault; + } if (type == TYPE_LDST) do_alignment_finish_ldst(addr, instr, regs, offset); @@ -735,7 +835,6 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs) bad_or_fault: if (type == TYPE_ERROR) goto bad; - regs->ARM_pc -= thumb_mode(regs) ? 2 : 4; /* * We got a fault - fix it up, or die. */ @@ -751,8 +850,8 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs) */ printk(KERN_ERR "Alignment trap: not handling instruction " "%0*lx at [<%08lx>]\n", - thumb_mode(regs) ? 4 : 8, - thumb_mode(regs) ? tinstr : instr, instrptr); + isize << 1, + isize == 2 ? tinstr : instr, instrptr); ai_skipped += 1; return 1; @@ -763,8 +862,8 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs) printk("Alignment trap: %s (%d) PC=0x%08lx Instr=0x%0*lx " "Address=0x%08lx FSR 0x%03x\n", current->comm, task_pid_nr(current), instrptr, - thumb_mode(regs) ? 4 : 8, - thumb_mode(regs) ? tinstr : instr, + isize << 1, + isize == 2 ? tinstr : instr, addr, fsr); if (ai_usermode & UM_FIXUP) diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c index fdaa9bb87c16..4722582b17b8 100644 --- a/arch/arm/mm/mmu.c +++ b/arch/arm/mm/mmu.c @@ -836,6 +836,13 @@ void __init reserve_node_zero(pg_data_t *pgdat) BOOTMEM_EXCLUSIVE); } + if (machine_is_treo680()) { + reserve_bootmem_node(pgdat, 0xa0000000, 0x1000, + BOOTMEM_EXCLUSIVE); + reserve_bootmem_node(pgdat, 0xa2000000, 0x1000, + BOOTMEM_EXCLUSIVE); + } + if (machine_is_palmt5()) reserve_bootmem_node(pgdat, 0xa0200000, 0x1000, BOOTMEM_EXCLUSIVE); diff --git a/arch/arm/plat-omap/include/mach/sram.h b/arch/arm/plat-omap/include/mach/sram.h index dca7c16ae903..4d53cc59d7a3 100644 --- a/arch/arm/plat-omap/include/mach/sram.h +++ b/arch/arm/plat-omap/include/mach/sram.h @@ -24,7 +24,8 @@ extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass); extern u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, u32 sdrc_actim_ctrlb, u32 m2, - u32 unlock_dll); + u32 unlock_dll, u32 f, u32 sdrc_mr, + u32 inc); /* Do not use these */ extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl); @@ -62,7 +63,8 @@ extern unsigned long omap243x_sram_reprogram_sdrc_sz; extern u32 omap3_sram_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, u32 sdrc_actim_ctrlb, u32 m2, - u32 unlock_dll); + u32 unlock_dll, u32 f, u32 sdrc_mr, + u32 inc); extern unsigned long omap3_sram_configure_core_dpll_sz; #endif diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c index a5b9bcd6b108..65006df3f1b7 100644 --- a/arch/arm/plat-omap/sram.c +++ b/arch/arm/plat-omap/sram.c @@ -371,15 +371,17 @@ static inline int omap243x_sram_init(void) static u32 (*_omap3_sram_configure_core_dpll)(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, u32 sdrc_actim_ctrlb, - u32 m2, u32 unlock_dll); + u32 m2, u32 unlock_dll, + u32 f, u32 sdrc_mr, u32 inc); u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, - u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll) + u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll, + u32 f, u32 sdrc_mr, u32 inc) { BUG_ON(!_omap3_sram_configure_core_dpll); return _omap3_sram_configure_core_dpll(sdrc_rfr_ctrl, sdrc_actim_ctrla, sdrc_actim_ctrlb, m2, - unlock_dll); + unlock_dll, f, sdrc_mr, inc); } /* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */ diff --git a/arch/arm/plat-s3c/Makefile b/arch/arm/plat-s3c/Makefile index 610651455a78..74bb7cb5da49 100644 --- a/arch/arm/plat-s3c/Makefile +++ b/arch/arm/plat-s3c/Makefile @@ -34,6 +34,7 @@ obj-$(CONFIG_S3C_DEV_HSMMC) += dev-hsmmc.o obj-$(CONFIG_S3C_DEV_HSMMC1) += dev-hsmmc1.o obj-y += dev-i2c0.o obj-$(CONFIG_S3C_DEV_I2C1) += dev-i2c1.o +obj-$(CONFIG_SND_S3C24XX_SOC) += dev-audio.o obj-$(CONFIG_S3C_DEV_FB) += dev-fb.o obj-$(CONFIG_S3C_DEV_USB_HOST) += dev-usb.o obj-$(CONFIG_S3C_DEV_USB_HSOTG) += dev-usb-hsotg.o diff --git a/arch/arm/plat-s3c/dev-audio.c b/arch/arm/plat-s3c/dev-audio.c new file mode 100644 index 000000000000..1322beb40dd7 --- /dev/null +++ b/arch/arm/plat-s3c/dev-audio.c @@ -0,0 +1,68 @@ +/* linux/arch/arm/plat-s3c/dev-audio.c + * + * Copyright 2009 Wolfson Microelectronics + * Mark Brown <broonie@opensource.wolfsonmicro.com> + * + + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/platform_device.h> + +#include <mach/irqs.h> +#include <mach/map.h> + +#include <plat/devs.h> + + +static struct resource s3c64xx_iis0_resource[] = { + [0] = { + .start = S3C64XX_PA_IIS0, + .end = S3C64XX_PA_IIS0 + 0x100 - 1, + .flags = IORESOURCE_MEM, + }, +}; + +struct platform_device s3c64xx_device_iis0 = { + .name = "s3c64xx-iis", + .id = 0, + .num_resources = ARRAY_SIZE(s3c64xx_iis0_resource), + .resource = s3c64xx_iis0_resource, +}; +EXPORT_SYMBOL(s3c64xx_device_iis0); + +static struct resource s3c64xx_iis1_resource[] = { + [0] = { + .start = S3C64XX_PA_IIS1, + .end = S3C64XX_PA_IIS1 + 0x100 - 1, + .flags = IORESOURCE_MEM, + }, +}; + +struct platform_device s3c64xx_device_iis1 = { + .name = "s3c64xx-iis", + .id = 1, + .num_resources = ARRAY_SIZE(s3c64xx_iis1_resource), + .resource = s3c64xx_iis1_resource, +}; +EXPORT_SYMBOL(s3c64xx_device_iis1); + +static struct resource s3c64xx_iisv4_resource[] = { + [0] = { + .start = S3C64XX_PA_IISV4, + .end = S3C64XX_PA_IISV4 + 0x100 - 1, + .flags = IORESOURCE_MEM, + }, +}; + +struct platform_device s3c64xx_device_iisv4 = { + .name = "s3c64xx-iis-v4", + .id = -1, + .num_resources = ARRAY_SIZE(s3c64xx_iisv4_resource), + .resource = s3c64xx_iisv4_resource, +}; +EXPORT_SYMBOL(s3c64xx_device_iisv4); diff --git a/arch/arm/plat-s3c/gpio-config.c b/arch/arm/plat-s3c/gpio-config.c index 08044dec9731..456969b6fa0d 100644 --- a/arch/arm/plat-s3c/gpio-config.c +++ b/arch/arm/plat-s3c/gpio-config.c @@ -119,7 +119,7 @@ int s3c_gpio_setcfg_s3c64xx_4bit(struct s3c_gpio_chip *chip, unsigned int shift = (off & 7) * 4; u32 con; - if (off < 8 && chip->chip.ngpio >= 8) + if (off < 8 && chip->chip.ngpio > 8) reg -= 4; if (s3c_gpio_is_cfg_special(cfg)) { diff --git a/arch/arm/plat-s3c/include/plat/devs.h b/arch/arm/plat-s3c/include/plat/devs.h index a0b6768fddcf..b5b9c4d46e9a 100644 --- a/arch/arm/plat-s3c/include/plat/devs.h +++ b/arch/arm/plat-s3c/include/plat/devs.h @@ -24,13 +24,16 @@ extern struct platform_device *s3c24xx_uart_src[]; extern struct platform_device s3c_device_timer[]; +extern struct platform_device s3c64xx_device_iis0; +extern struct platform_device s3c64xx_device_iis1; +extern struct platform_device s3c64xx_device_iisv4; + extern struct platform_device s3c_device_fb; extern struct platform_device s3c_device_usb; extern struct platform_device s3c_device_lcd; extern struct platform_device s3c_device_wdt; extern struct platform_device s3c_device_i2c0; extern struct platform_device s3c_device_i2c1; -extern struct platform_device s3c_device_iis; extern struct platform_device s3c_device_rtc; extern struct platform_device s3c_device_adc; extern struct platform_device s3c_device_sdi; diff --git a/arch/arm/plat-s3c64xx/Makefile b/arch/arm/plat-s3c64xx/Makefile index 2ed5df34f9ea..3c8882cd6268 100644 --- a/arch/arm/plat-s3c64xx/Makefile +++ b/arch/arm/plat-s3c64xx/Makefile @@ -23,6 +23,7 @@ obj-y += gpiolib.o obj-$(CONFIG_CPU_S3C6400_INIT) += s3c6400-init.o obj-$(CONFIG_CPU_S3C6400_CLOCK) += s3c6400-clock.o +obj-$(CONFIG_CPU_FREQ_S3C64XX) += cpufreq.o # PM support diff --git a/arch/arm/plat-s3c64xx/clock.c b/arch/arm/plat-s3c64xx/clock.c index 0bc2fa1dfc40..7a36e899360d 100644 --- a/arch/arm/plat-s3c64xx/clock.c +++ b/arch/arm/plat-s3c64xx/clock.c @@ -191,7 +191,7 @@ static struct clk init_clocks[] = { .id = -1, .parent = &clk_h, .enable = s3c64xx_hclk_ctrl, - .ctrlbit = S3C_CLKCON_SCLK_UHOST, + .ctrlbit = S3C_CLKCON_HCLK_UHOST, }, { .name = "hsmmc", .id = 0, diff --git a/arch/arm/plat-s3c64xx/cpufreq.c b/arch/arm/plat-s3c64xx/cpufreq.c new file mode 100644 index 000000000000..e6e0843215df --- /dev/null +++ b/arch/arm/plat-s3c64xx/cpufreq.c @@ -0,0 +1,262 @@ +/* linux/arch/arm/plat-s3c64xx/cpufreq.c + * + * Copyright 2009 Wolfson Microelectronics plc + * + * S3C64xx CPUfreq Support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/init.h> +#include <linux/cpufreq.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/regulator/consumer.h> + +static struct clk *armclk; +static struct regulator *vddarm; + +#ifdef CONFIG_CPU_S3C6410 +struct s3c64xx_dvfs { + unsigned int vddarm_min; + unsigned int vddarm_max; +}; + +static struct s3c64xx_dvfs s3c64xx_dvfs_table[] = { + [0] = { 1000000, 1000000 }, + [1] = { 1000000, 1050000 }, + [2] = { 1050000, 1100000 }, + [3] = { 1050000, 1150000 }, + [4] = { 1250000, 1350000 }, +}; + +static struct cpufreq_frequency_table s3c64xx_freq_table[] = { + { 0, 66000 }, + { 0, 133000 }, + { 1, 222000 }, + { 1, 266000 }, + { 2, 333000 }, + { 2, 400000 }, + { 3, 532000 }, + { 3, 533000 }, + { 4, 667000 }, + { 0, CPUFREQ_TABLE_END }, +}; +#endif + +static int s3c64xx_cpufreq_verify_speed(struct cpufreq_policy *policy) +{ + if (policy->cpu != 0) + return -EINVAL; + + return cpufreq_frequency_table_verify(policy, s3c64xx_freq_table); +} + +static unsigned int s3c64xx_cpufreq_get_speed(unsigned int cpu) +{ + if (cpu != 0) + return 0; + + return clk_get_rate(armclk) / 1000; +} + +static int s3c64xx_cpufreq_set_target(struct cpufreq_policy *policy, + unsigned int target_freq, + unsigned int relation) +{ + int ret; + unsigned int i; + struct cpufreq_freqs freqs; + struct s3c64xx_dvfs *dvfs; + + ret = cpufreq_frequency_table_target(policy, s3c64xx_freq_table, + target_freq, relation, &i); + if (ret != 0) + return ret; + + freqs.cpu = 0; + freqs.old = clk_get_rate(armclk) / 1000; + freqs.new = s3c64xx_freq_table[i].frequency; + freqs.flags = 0; + dvfs = &s3c64xx_dvfs_table[s3c64xx_freq_table[i].index]; + + if (freqs.old == freqs.new) + return 0; + + pr_debug("cpufreq: Transition %d-%dkHz\n", freqs.old, freqs.new); + + cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); + +#ifdef CONFIG_REGULATOR + if (vddarm && freqs.new > freqs.old) { + ret = regulator_set_voltage(vddarm, + dvfs->vddarm_min, + dvfs->vddarm_max); + if (ret != 0) { + pr_err("cpufreq: Failed to set VDDARM for %dkHz: %d\n", + freqs.new, ret); + goto err; + } + } +#endif + + ret = clk_set_rate(armclk, freqs.new * 1000); + if (ret < 0) { + pr_err("cpufreq: Failed to set rate %dkHz: %d\n", + freqs.new, ret); + goto err; + } + +#ifdef CONFIG_REGULATOR + if (vddarm && freqs.new < freqs.old) { + ret = regulator_set_voltage(vddarm, + dvfs->vddarm_min, + dvfs->vddarm_max); + if (ret != 0) { + pr_err("cpufreq: Failed to set VDDARM for %dkHz: %d\n", + freqs.new, ret); + goto err_clk; + } + } +#endif + + cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); + + pr_debug("cpufreq: Set actual frequency %lukHz\n", + clk_get_rate(armclk) / 1000); + + return 0; + +err_clk: + if (clk_set_rate(armclk, freqs.old * 1000) < 0) + pr_err("Failed to restore original clock rate\n"); +err: + cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); + + return ret; +} + +#ifdef CONFIG_REGULATOR +static void __init s3c64xx_cpufreq_constrain_voltages(void) +{ + int count, v, i, found; + struct cpufreq_frequency_table *freq; + struct s3c64xx_dvfs *dvfs; + + count = regulator_count_voltages(vddarm); + if (count < 0) { + pr_err("cpufreq: Unable to check supported voltages\n"); + return; + } + + freq = s3c64xx_freq_table; + while (freq->frequency != CPUFREQ_TABLE_END) { + if (freq->frequency == CPUFREQ_ENTRY_INVALID) + continue; + + dvfs = &s3c64xx_dvfs_table[freq->index]; + found = 0; + + for (i = 0; i < count; i++) { + v = regulator_list_voltage(vddarm, i); + if (v >= dvfs->vddarm_min && v <= dvfs->vddarm_max) + found = 1; + } + + if (!found) { + pr_debug("cpufreq: %dkHz unsupported by regulator\n", + freq->frequency); + freq->frequency = CPUFREQ_ENTRY_INVALID; + } + + freq++; + } +} +#endif + +static int __init s3c64xx_cpufreq_driver_init(struct cpufreq_policy *policy) +{ + int ret; + struct cpufreq_frequency_table *freq; + + if (policy->cpu != 0) + return -EINVAL; + + if (s3c64xx_freq_table == NULL) { + pr_err("cpufreq: No frequency information for this CPU\n"); + return -ENODEV; + } + + armclk = clk_get(NULL, "armclk"); + if (IS_ERR(armclk)) { + pr_err("cpufreq: Unable to obtain ARMCLK: %ld\n", + PTR_ERR(armclk)); + return PTR_ERR(armclk); + } + +#ifdef CONFIG_REGULATOR + vddarm = regulator_get(NULL, "vddarm"); + if (IS_ERR(vddarm)) { + ret = PTR_ERR(vddarm); + pr_err("cpufreq: Failed to obtain VDDARM: %d\n", ret); + pr_err("cpufreq: Only frequency scaling available\n"); + vddarm = NULL; + } else { + s3c64xx_cpufreq_constrain_voltages(); + } +#endif + + freq = s3c64xx_freq_table; + while (freq->frequency != CPUFREQ_TABLE_END) { + unsigned long r; + + /* Check for frequencies we can generate */ + r = clk_round_rate(armclk, freq->frequency * 1000); + r /= 1000; + if (r != freq->frequency) + freq->frequency = CPUFREQ_ENTRY_INVALID; + + /* If we have no regulator then assume startup + * frequency is the maximum we can support. */ + if (!vddarm && freq->frequency > s3c64xx_cpufreq_get_speed(0)) + freq->frequency = CPUFREQ_ENTRY_INVALID; + + freq++; + } + + policy->cur = clk_get_rate(armclk) / 1000; + + /* Pick a conservative guess in ns: we'll need ~1 I2C/SPI + * write plus clock reprogramming. */ + policy->cpuinfo.transition_latency = 2 * 1000 * 1000; + + ret = cpufreq_frequency_table_cpuinfo(policy, s3c64xx_freq_table); + if (ret != 0) { + pr_err("cpufreq: Failed to configure frequency table: %d\n", + ret); + regulator_put(vddarm); + clk_put(armclk); + } + + return ret; +} + +static struct cpufreq_driver s3c64xx_cpufreq_driver = { + .owner = THIS_MODULE, + .flags = 0, + .verify = s3c64xx_cpufreq_verify_speed, + .target = s3c64xx_cpufreq_set_target, + .get = s3c64xx_cpufreq_get_speed, + .init = s3c64xx_cpufreq_driver_init, + .name = "s3c", +}; + +static int __init s3c64xx_cpufreq_init(void) +{ + return cpufreq_register_driver(&s3c64xx_cpufreq_driver); +} +module_init(s3c64xx_cpufreq_init); diff --git a/arch/arm/plat-s3c64xx/gpiolib.c b/arch/arm/plat-s3c64xx/gpiolib.c index da7b60ee5e67..92859290ea33 100644 --- a/arch/arm/plat-s3c64xx/gpiolib.c +++ b/arch/arm/plat-s3c64xx/gpiolib.c @@ -321,6 +321,11 @@ static struct s3c_gpio_cfg gpio_2bit_cfg_eint11 = { .get_pull = s3c_gpio_getpull_updown, }; +int s3c64xx_gpio2int_gpn(struct gpio_chip *chip, unsigned pin) +{ + return IRQ_EINT(0) + pin; +} + static struct s3c_gpio_chip gpio_2bit[] = { { .base = S3C64XX_GPF_BASE, @@ -353,6 +358,7 @@ static struct s3c_gpio_chip gpio_2bit[] = { .base = S3C64XX_GPN(0), .ngpio = S3C64XX_GPIO_N_NR, .label = "GPN", + .to_irq = s3c64xx_gpio2int_gpn, }, }, { .base = S3C64XX_GPO_BASE, diff --git a/arch/arm/plat-s3c64xx/include/plat/regs-clock.h b/arch/arm/plat-s3c64xx/include/plat/regs-clock.h index 52836d41e333..a8777a755dfa 100644 --- a/arch/arm/plat-s3c64xx/include/plat/regs-clock.h +++ b/arch/arm/plat-s3c64xx/include/plat/regs-clock.h @@ -88,11 +88,11 @@ #define S3C6400_CLKDIV2_SPI0_SHIFT (0) /* HCLK GATE Registers */ -#define S3C_CLKCON_HCLK_BUS (1<<30) -#define S3C_CLKCON_HCLK_SECUR (1<<29) -#define S3C_CLKCON_HCLK_SDMA1 (1<<28) -#define S3C_CLKCON_HCLK_SDMA2 (1<<27) -#define S3C_CLKCON_HCLK_UHOST (1<<26) +#define S3C_CLKCON_HCLK_3DSE (1<<31) +#define S3C_CLKCON_HCLK_UHOST (1<<29) +#define S3C_CLKCON_HCLK_SECUR (1<<28) +#define S3C_CLKCON_HCLK_SDMA1 (1<<27) +#define S3C_CLKCON_HCLK_SDMA0 (1<<26) #define S3C_CLKCON_HCLK_IROM (1<<25) #define S3C_CLKCON_HCLK_DDR1 (1<<24) #define S3C_CLKCON_HCLK_DDR0 (1<<23) diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types index fec64678a63a..33026eff2aa4 100644 --- a/arch/arm/tools/mach-types +++ b/arch/arm/tools/mach-types @@ -12,7 +12,7 @@ # # http://www.arm.linux.org.uk/developer/machines/?action=new # -# Last update: Fri May 29 10:14:20 2009 +# Last update: Sat Jun 20 22:28:39 2009 # # machine_is_xxx CONFIG_xxxx MACH_TYPE_xxx number # @@ -1455,7 +1455,7 @@ gba MACH_GBA GBA 1457 h6044 MACH_H6044 H6044 1458 app MACH_APP APP 1459 tct_hammer MACH_TCT_HAMMER TCT_HAMMER 1460 -herald MACH_HERMES HERMES 1461 +herald MACH_HERALD HERALD 1461 artemis MACH_ARTEMIS ARTEMIS 1462 htctitan MACH_HTCTITAN HTCTITAN 1463 qranium MACH_QRANIUM QRANIUM 1464 @@ -2245,3 +2245,38 @@ str9 MACH_STR9 STR9 2257 omap3_wl_ff MACH_OMAP3_WL_FF OMAP3_WL_FF 2258 simcom MACH_SIMCOM SIMCOM 2259 mcwebio MACH_MCWEBIO MCWEBIO 2260 +omap3_phrazer MACH_OMAP3_PHRAZER OMAP3_PHRAZER 2261 +darwin MACH_DARWIN DARWIN 2262 +oratiscomu MACH_ORATISCOMU ORATISCOMU 2263 +rtsbc20 MACH_RTSBC20 RTSBC20 2264 +i780 MACH_I780 I780 2265 +gemini324 MACH_GEMINI324 GEMINI324 2266 +oratislan MACH_ORATISLAN ORATISLAN 2267 +oratisalog MACH_ORATISALOG ORATISALOG 2268 +oratismadi MACH_ORATISMADI ORATISMADI 2269 +oratisot16 MACH_ORATISOT16 ORATISOT16 2270 +oratisdesk MACH_ORATISDESK ORATISDESK 2271 +v2p_ca9 MACH_V2P_CA9 V2P_CA9 2272 +sintexo MACH_SINTEXO SINTEXO 2273 +cm3389 MACH_CM3389 CM3389 2274 +omap3_cio MACH_OMAP3_CIO OMAP3_CIO 2275 +sgh_i900 MACH_SGH_I900 SGH_I900 2276 +bst100 MACH_BST100 BST100 2277 +passion MACH_PASSION PASSION 2278 +indesign_at91sam MACH_INDESIGN_AT91SAM INDESIGN_AT91SAM 2279 +c4_badger MACH_C4_BADGER C4_BADGER 2280 +c4_viper MACH_C4_VIPER C4_VIPER 2281 +d2net MACH_D2NET D2NET 2282 +bigdisk MACH_BIGDISK BIGDISK 2283 +notalvision MACH_NOTALVISION NOTALVISION 2284 +omap3_kboc MACH_OMAP3_KBOC OMAP3_KBOC 2285 +cyclone MACH_CYCLONE CYCLONE 2286 +ninja MACH_NINJA NINJA 2287 +at91sam9g20ek_2mmc MACH_AT91SAM9G20EK_2MMC AT91SAM9G20EK_2MMC 2288 +bcmring MACH_BCMRING BCMRING 2289 +resol_dl2 MACH_RESOL_DL2 RESOL_DL2 2290 +ifosw MACH_IFOSW IFOSW 2291 +htcrhodium MACH_HTCRHODIUM HTCRHODIUM 2292 +htctopaz MACH_HTCTOPAZ HTCTOPAZ 2293 +matrix504 MACH_MATRIX504 MATRIX504 2294 +mrfsa MACH_MRFSA MRFSA 2295 diff --git a/sound/soc/pxa/corgi.c b/sound/soc/pxa/corgi.c index d5be2b30cda5..fefe1a57f31a 100644 --- a/sound/soc/pxa/corgi.c +++ b/sound/soc/pxa/corgi.c @@ -320,38 +320,6 @@ static struct snd_soc_device corgi_snd_devdata = { .codec_dev = &soc_codec_dev_wm8731, }; -/* - * FIXME: This is a temporary bodge to avoid cross-tree merge issues. - * New drivers should register the wm8731 I2C device in the machine - * setup code (under arch/arm for ARM systems). - */ -static int wm8731_i2c_register(void) -{ - struct i2c_board_info info; - struct i2c_adapter *adapter; - struct i2c_client *client; - - memset(&info, 0, sizeof(struct i2c_board_info)); - info.addr = 0x1b; - strlcpy(info.type, "wm8731", I2C_NAME_SIZE); - - adapter = i2c_get_adapter(0); - if (!adapter) { - printk(KERN_ERR "can't get i2c adapter 0\n"); - return -ENODEV; - } - - client = i2c_new_device(adapter, &info); - i2c_put_adapter(adapter); - if (!client) { - printk(KERN_ERR "can't add i2c device at 0x%x\n", - (unsigned int)info.addr); - return -ENODEV; - } - - return 0; -} - static struct platform_device *corgi_snd_device; static int __init corgi_init(void) @@ -362,10 +330,6 @@ static int __init corgi_init(void) machine_is_husky())) return -ENODEV; - ret = wm8731_i2c_register(); - if (ret != 0) - return ret; - corgi_snd_device = platform_device_alloc("soc-audio", -1); if (!corgi_snd_device) return -ENOMEM; diff --git a/sound/soc/pxa/poodle.c b/sound/soc/pxa/poodle.c index a51058f66747..c5f36e0eab58 100644 --- a/sound/soc/pxa/poodle.c +++ b/sound/soc/pxa/poodle.c @@ -280,38 +280,6 @@ static struct snd_soc_card snd_soc_poodle = { .num_links = 1, }; -/* - * FIXME: This is a temporary bodge to avoid cross-tree merge issues. - * New drivers should register the wm8731 I2C device in the machine - * setup code (under arch/arm for ARM systems). - */ -static int wm8731_i2c_register(void) -{ - struct i2c_board_info info; - struct i2c_adapter *adapter; - struct i2c_client *client; - - memset(&info, 0, sizeof(struct i2c_board_info)); - info.addr = 0x1b; - strlcpy(info.type, "wm8731", I2C_NAME_SIZE); - - adapter = i2c_get_adapter(0); - if (!adapter) { - printk(KERN_ERR "can't get i2c adapter 0\n"); - return -ENODEV; - } - - client = i2c_new_device(adapter, &info); - i2c_put_adapter(adapter); - if (!client) { - printk(KERN_ERR "can't add i2c device at 0x%x\n", - (unsigned int)info.addr); - return -ENODEV; - } - - return 0; -} - /* poodle audio subsystem */ static struct snd_soc_device poodle_snd_devdata = { .card = &snd_soc_poodle, @@ -327,10 +295,6 @@ static int __init poodle_init(void) if (!machine_is_poodle()) return -ENODEV; - ret = wm8731_i2c_register(); - if (ret != 0) - return ret; - locomo_gpio_set_dir(&poodle_locomo_device.dev, POODLE_LOCOMO_GPIO_AMP_ON, 0); /* should we mute HP at startup - burning power ?*/ |
