USB: remove CONFIG_USB_SUSPEND option

This patch (as1675) removes the CONFIG_USB_SUSPEND option, essentially
replacing it everywhere with CONFIG_PM_RUNTIME (except for one place
in hub.c, where it is replaced with CONFIG_PM because the code needs
to be used in both runtime and system PM).  The net result is code
shrinkage and simplification.

There's very little point in keeping CONFIG_USB_SUSPEND because almost
everybody enables it.  The few that don't will find that the usbcore
module has gotten somewhat bigger and they will have to take active
measures if they want to prevent hubs from being runtime suspended.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 files changed, 10 insertions, 25 deletions

diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c
index 170b9399e09f..a573d5ff9adc 100644
--- a/drivers/usb/host/ehci-pci.c
+++ b/drivers/usb/host/ehci-pci.c
@@ -292,17 +292,7 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 		}
 	}
 
-#ifdef	CONFIG_USB_SUSPEND
-	/* REVISIT: the controller works fine for wakeup iff the root hub
-	 * itself is "globally" suspended, but usbcore currently doesn't
-	 * understand such things.
-	 *
-	 * System suspend currently expects to be able to suspend the entire
-	 * device tree, device-at-a-time.  If we failed selective suspend
-	 * reports, system suspend would fail; so the root hub code must claim
-	 * success.  That's lying to usbcore, and it matters for runtime
-	 * PM scenarios with selective suspend and remote wakeup...
-	 */
+#ifdef	CONFIG_PM_RUNTIME
 	if (ehci->no_selective_suspend && device_can_wakeup(&pdev->dev))
 		ehci_warn(ehci, "selective suspend/wakeup unavailable\n");
 #endif
diff --git a/drivers/usb/host/ohci-hub.c b/drivers/usb/host/ohci-hub.c
index db09dae7b557..60ff4220e8b4 100644
--- a/drivers/usb/host/ohci-hub.c
+++ b/drivers/usb/host/ohci-hub.c
@@ -580,14 +580,8 @@ static int ohci_start_port_reset (struct usb_hcd *hcd, unsigned port)
 
 /* See usb 7.1.7.5:  root hubs must issue at least 50 msec reset signaling,
  * not necessarily continuous ... to guard against resume signaling.
- * The short timeout is safe for non-root hubs, and is backward-compatible
- * with earlier Linux hosts.
  */
-#ifdef	CONFIG_USB_SUSPEND
 #define	PORT_RESET_MSEC		50
-#else
-#define	PORT_RESET_MSEC		10
-#endif
 
 /* this timer value might be vendor-specific ... */
 #define	PORT_RESET_HW_MSEC	10
diff --git a/drivers/usb/host/sl811-hcd.c b/drivers/usb/host/sl811-hcd.c
index d62f0404baaa..15ed7e8d887f 100644
--- a/drivers/usb/host/sl811-hcd.c
+++ b/drivers/usb/host/sl811-hcd.c
@@ -1755,7 +1755,7 @@ sl811h_probe(struct platform_device *dev)
 
 /* for this device there's no useful distinction between the controller
  * and its root hub, except that the root hub only gets direct PM calls
- * when CONFIG_USB_SUSPEND is enabled.
+ * when CONFIG_PM_RUNTIME is enabled.
  */
 
 static int
diff --git a/drivers/usb/host/u132-hcd.c b/drivers/usb/host/u132-hcd.c
index 5efdffe32365..5c124bf5d018 100644
--- a/drivers/usb/host/u132-hcd.c
+++ b/drivers/usb/host/u132-hcd.c
@@ -3141,10 +3141,11 @@ static int u132_probe(struct platform_device *pdev)
 
 
 #ifdef CONFIG_PM
-/* for this device there's no useful distinction between the controller
-* and its root hub, except that the root hub only gets direct PM calls
-* when CONFIG_USB_SUSPEND is enabled.
-*/
+/*
+ * for this device there's no useful distinction between the controller
+ * and its root hub, except that the root hub only gets direct PM calls
+ * when CONFIG_PM_RUNTIME is enabled.
+ */
 static int u132_suspend(struct platform_device *pdev, pm_message_t state)
 {
 	struct usb_hcd *hcd = platform_get_drvdata(pdev);
diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index 68914429482f..187a3ec1069a 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -1075,7 +1075,7 @@ int xhci_bus_suspend(struct usb_hcd *hcd)
 			set_bit(port_index, &bus_state->bus_suspended);
 		}
 		/* USB core sets remote wake mask for USB 3.0 hubs,
-		 * including the USB 3.0 roothub, but only if CONFIG_USB_SUSPEND
+		 * including the USB 3.0 roothub, but only if CONFIG_PM_RUNTIME
 		 * is enabled, so also enable remote wake here.
 		 */
 		if (hcd->self.root_hub->do_remote_wakeup) {
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 53b8f89a0b1c..5156b720a53a 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -3801,7 +3801,7 @@ int xhci_find_raw_port_number(struct usb_hcd *hcd, int port1)
 	return raw_port;
 }
 
-#ifdef CONFIG_USB_SUSPEND
+#ifdef CONFIG_PM_RUNTIME
 
 /* BESL to HIRD Encoding array for USB2 LPM */
 static int xhci_besl_encoding[16] = {125, 150, 200, 300, 400, 500, 1000, 2000,
@@ -4051,7 +4051,7 @@ int xhci_update_device(struct usb_hcd *hcd, struct usb_device *udev)
 	return 0;
 }
 
-#endif /* CONFIG_USB_SUSPEND */
+#endif /* CONFIG_PM_RUNTIME */
 
 /*---------------------- USB 3.0 Link PM functions ------------------------*/