Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6

26 files changed, 1038 insertions, 830 deletions

diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 350d14fc1cc9..58321d3f314c 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -1,8 +1,9 @@
 #
-# Makefile for USB Host Controller Driver
-# framework and drivers
+# Makefile for USB Host Controller Drivers
 #
 
+obj-$(CONFIG_PCI)		+= pci-quirks.o
+
 obj-$(CONFIG_USB_EHCI_HCD)	+= ehci-hcd.o
 obj-$(CONFIG_USB_ISP116X_HCD)	+= isp116x-hcd.o
 obj-$(CONFIG_USB_OHCI_HCD)	+= ohci-hcd.o
diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c
index f5eb9e7b5b18..af3c05eb86fc 100644
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -182,6 +182,9 @@ static int ehci_halt (struct ehci_hcd *ehci)
 {
 	u32	temp = readl (&ehci->regs->status);
 
+	/* disable any irqs left enabled by previous code */
+	writel (0, &ehci->regs->intr_enable);
+
 	if ((temp & STS_HALT) != 0)
 		return 0;
 
@@ -297,50 +300,17 @@ static void ehci_watchdog (unsigned long param)
 	spin_unlock_irqrestore (&ehci->lock, flags);
 }
 
-#ifdef	CONFIG_PCI
-
-/* EHCI 0.96 (and later) section 5.1 says how to kick BIOS/SMM/...
- * off the controller (maybe it can boot from highspeed USB disks).
+/* Reboot notifiers kick in for silicon on any bus (not just pci, etc).
+ * This forcibly disables dma and IRQs, helping kexec and other cases
+ * where the next system software may expect clean state.
  */
-static int bios_handoff (struct ehci_hcd *ehci, int where, u32 cap)
-{
-	struct pci_dev *pdev = to_pci_dev(ehci_to_hcd(ehci)->self.controller);
-
-	/* always say Linux will own the hardware */
-	pci_write_config_byte(pdev, where + 3, 1);
-
-	/* maybe wait a while for BIOS to respond */
-	if (cap & (1 << 16)) {
-		int msec = 5000;
-
-		do {
-			msleep(10);
-			msec -= 10;
-			pci_read_config_dword(pdev, where, &cap);
-		} while ((cap & (1 << 16)) && msec);
-		if (cap & (1 << 16)) {
-			ehci_err(ehci, "BIOS handoff failed (%d, %08x)\n",
-				where, cap);
-			// some BIOS versions seem buggy...
-			// return 1;
-			ehci_warn (ehci, "continuing after BIOS bug...\n");
-			/* disable all SMIs, and clear "BIOS owns" flag */
-			pci_write_config_dword(pdev, where + 4, 0);
-			pci_write_config_byte(pdev, where + 2, 0);
-		} else
-			ehci_dbg(ehci, "BIOS handoff succeeded\n");
-	}
-	return 0;
-}
-
-#endif
-
 static int
 ehci_reboot (struct notifier_block *self, unsigned long code, void *null)
 {
 	struct ehci_hcd		*ehci;
 
 	ehci = container_of (self, struct ehci_hcd, reboot_notifier);
+	(void) ehci_halt (ehci);
 
 	/* make BIOS/etc use companion controller during reboot */
 	writel (0, &ehci->regs->configured_flag);
@@ -363,156 +333,90 @@ static void ehci_port_power (struct ehci_hcd *ehci, int is_on)
 	msleep(20);
 }
 
+/*-------------------------------------------------------------------------*/
+
+/*
+ * ehci_work is called from some interrupts, timers, and so on.
+ * it calls driver completion functions, after dropping ehci->lock.
+ */
+static void ehci_work (struct ehci_hcd *ehci, struct pt_regs *regs)
+{
+	timer_action_done (ehci, TIMER_IO_WATCHDOG);
+	if (ehci->reclaim_ready)
+		end_unlink_async (ehci, regs);
+
+	/* another CPU may drop ehci->lock during a schedule scan while
+	 * it reports urb completions.  this flag guards against bogus
+	 * attempts at re-entrant schedule scanning.
+	 */
+	if (ehci->scanning)
+		return;
+	ehci->scanning = 1;
+	scan_async (ehci, regs);
+	if (ehci->next_uframe != -1)
+		scan_periodic (ehci, regs);
+	ehci->scanning = 0;
 
-/* called by khubd or root hub init threads */
+	/* the IO watchdog guards against hardware or driver bugs that
+	 * misplace IRQs, and should let us run completely without IRQs.
+	 * such lossage has been observed on both VT6202 and VT8235.
+	 */
+	if (HC_IS_RUNNING (ehci_to_hcd(ehci)->state) &&
+			(ehci->async->qh_next.ptr != NULL ||
+			 ehci->periodic_sched != 0))
+		timer_action (ehci, TIMER_IO_WATCHDOG);
+}
 
-static int ehci_hc_reset (struct usb_hcd *hcd)
+static void ehci_stop (struct usb_hcd *hcd)
 {
 	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
-	u32			temp;
-	unsigned		count = 256/4;
 
-	spin_lock_init (&ehci->lock);
+	ehci_dbg (ehci, "stop\n");
 
-	ehci->caps = hcd->regs;
-	ehci->regs = hcd->regs + HC_LENGTH (readl (&ehci->caps->hc_capbase));
-	dbg_hcs_params (ehci, "reset");
-	dbg_hcc_params (ehci, "reset");
+	/* Turn off port power on all root hub ports. */
+	ehci_port_power (ehci, 0);
 
-	/* cache this readonly data; minimize chip reads */
-	ehci->hcs_params = readl (&ehci->caps->hcs_params);
+	/* no more interrupts ... */
+	del_timer_sync (&ehci->watchdog);
 
-#ifdef	CONFIG_PCI
-	if (hcd->self.controller->bus == &pci_bus_type) {
-		struct pci_dev	*pdev = to_pci_dev(hcd->self.controller);
+	spin_lock_irq(&ehci->lock);
+	if (HC_IS_RUNNING (hcd->state))
+		ehci_quiesce (ehci);
 
-		switch (pdev->vendor) {
-		case PCI_VENDOR_ID_TDI:
-			if (pdev->device == PCI_DEVICE_ID_TDI_EHCI) {
-				ehci->is_tdi_rh_tt = 1;
-				tdi_reset (ehci);
-			}
-			break;
-		case PCI_VENDOR_ID_AMD:
-			/* AMD8111 EHCI doesn't work, according to AMD errata */
-			if (pdev->device == 0x7463) {
-				ehci_info (ehci, "ignoring AMD8111 (errata)\n");
-				return -EIO;
-			}
-			break;
-		case PCI_VENDOR_ID_NVIDIA:
-			/* NVidia reports that certain chips don't handle
-			 * QH, ITD, or SITD addresses above 2GB.  (But TD,
-			 * data buffer, and periodic schedule are normal.)
-			 */
-			switch (pdev->device) {
-			case 0x003c:	/* MCP04 */
-			case 0x005b:	/* CK804 */
-			case 0x00d8:	/* CK8 */
-			case 0x00e8:	/* CK8S */
-				if (pci_set_consistent_dma_mask(pdev,
-							DMA_31BIT_MASK) < 0)
-					ehci_warn (ehci, "can't enable NVidia "
-						"workaround for >2GB RAM\n");
-				break;
-			}
-			break;
-		}
+	ehci_reset (ehci);
+	writel (0, &ehci->regs->intr_enable);
+	spin_unlock_irq(&ehci->lock);
 
-		/* optional debug port, normally in the first BAR */
-		temp = pci_find_capability (pdev, 0x0a);
-		if (temp) {
-			pci_read_config_dword(pdev, temp, &temp);
-			temp >>= 16;
-			if ((temp & (3 << 13)) == (1 << 13)) {
-				temp &= 0x1fff;
-				ehci->debug = hcd->regs + temp;
-				temp = readl (&ehci->debug->control);
-				ehci_info (ehci, "debug port %d%s\n",
-					HCS_DEBUG_PORT(ehci->hcs_params),
-					(temp & DBGP_ENABLED)
-						? " IN USE"
-						: "");
-				if (!(temp & DBGP_ENABLED))
-					ehci->debug = NULL;
-			}
-		}
+	/* let companion controllers work when we aren't */
+	writel (0, &ehci->regs->configured_flag);
+	unregister_reboot_notifier (&ehci->reboot_notifier);
 
-		temp = HCC_EXT_CAPS (readl (&ehci->caps->hcc_params));
-	} else
-		temp = 0;
-
-	/* EHCI 0.96 and later may have "extended capabilities" */
-	while (temp && count--) {
-		u32		cap;
-
-		pci_read_config_dword (to_pci_dev(hcd->self.controller),
-				temp, &cap);
-		ehci_dbg (ehci, "capability %04x at %02x\n", cap, temp);
-		switch (cap & 0xff) {
-		case 1:			/* BIOS/SMM/... handoff */
-			if (bios_handoff (ehci, temp, cap) != 0)
-				return -EOPNOTSUPP;
-			break;
-		case 0:			/* illegal reserved capability */
-			ehci_warn (ehci, "illegal capability!\n");
-			cap = 0;
-			/* FALLTHROUGH */
-		default:		/* unknown */
-			break;
-		}
-		temp = (cap >> 8) & 0xff;
-	}
-	if (!count) {
-		ehci_err (ehci, "bogus capabilities ... PCI problems!\n");
-		return -EIO;
-	}
-	if (ehci_is_TDI(ehci))
-		ehci_reset (ehci);
-#endif
+	remove_debug_files (ehci);
 
-	ehci_port_power (ehci, 0);
+	/* root hub is shut down separately (first, when possible) */
+	spin_lock_irq (&ehci->lock);
+	if (ehci->async)
+		ehci_work (ehci, NULL);
+	spin_unlock_irq (&ehci->lock);
+	ehci_mem_cleanup (ehci);
 
-	/* at least the Genesys GL880S needs fixup here */
-	temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params);
-	temp &= 0x0f;
-	if (temp && HCS_N_PORTS(ehci->hcs_params) > temp) {
-		ehci_dbg (ehci, "bogus port configuration: "
-			"cc=%d x pcc=%d < ports=%d\n",
-			HCS_N_CC(ehci->hcs_params),
-			HCS_N_PCC(ehci->hcs_params),
-			HCS_N_PORTS(ehci->hcs_params));
-
-#ifdef	CONFIG_PCI
-		if (hcd->self.controller->bus == &pci_bus_type) {
-			struct pci_dev	*pdev;
-
-			pdev = to_pci_dev(hcd->self.controller);
-			switch (pdev->vendor) {
-			case 0x17a0:		/* GENESYS */
-				/* GL880S: should be PORTS=2 */
-				temp |= (ehci->hcs_params & ~0xf);
-				ehci->hcs_params = temp;
-				break;
-			case PCI_VENDOR_ID_NVIDIA:
-				/* NF4: should be PCC=10 */
-				break;
-			}
-		}
+#ifdef	EHCI_STATS
+	ehci_dbg (ehci, "irq normal %ld err %ld reclaim %ld (lost %ld)\n",
+		ehci->stats.normal, ehci->stats.error, ehci->stats.reclaim,
+		ehci->stats.lost_iaa);
+	ehci_dbg (ehci, "complete %ld unlink %ld\n",
+		ehci->stats.complete, ehci->stats.unlink);
 #endif
-	}
 
-	/* force HC to halt state */
-	return ehci_halt (ehci);
+	dbg_status (ehci, "ehci_stop completed", readl (&ehci->regs->status));
 }
 
-static int ehci_start (struct usb_hcd *hcd)
+static int ehci_run (struct usb_hcd *hcd)
 {
 	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
 	u32			temp;
 	int			retval;
 	u32			hcc_params;
-	u8                      sbrn = 0;
 	int			first;
 
 	/* skip some things on restart paths */
@@ -551,27 +455,6 @@ static int ehci_start (struct usb_hcd *hcd)
 	}
 	writel (ehci->periodic_dma, &ehci->regs->frame_list);
 
-#ifdef	CONFIG_PCI
-	if (hcd->self.controller->bus == &pci_bus_type) {
-		struct pci_dev		*pdev;
-		u16			port_wake;
-
-		pdev = to_pci_dev(hcd->self.controller);
-
-		/* Serial Bus Release Number is at PCI 0x60 offset */
-		pci_read_config_byte(pdev, 0x60, &sbrn);
-
-		/* port wake capability, reported by boot firmware */
-		pci_read_config_word(pdev, 0x62, &port_wake);
-		hcd->can_wakeup = (port_wake & 1) != 0;
-
-		/* help hc dma work well with cachelines */
-		retval = pci_set_mwi(pdev);
-		if (retval)
-			ehci_dbg(ehci, "unable to enable MWI - not fatal.\n");
-	}
-#endif
-
 	/*
 	 * dedicate a qh for the async ring head, since we couldn't unlink
 	 * a 'real' qh without stopping the async schedule [4.8].  use it
@@ -667,7 +550,7 @@ static int ehci_start (struct usb_hcd *hcd)
 	temp = HC_VERSION(readl (&ehci->caps->hc_capbase));
 	ehci_info (ehci,
 		"USB %x.%x %s, EHCI %x.%02x, driver %s\n",
-		((sbrn & 0xf0)>>4), (sbrn & 0x0f),
+		((ehci->sbrn & 0xf0)>>4), (ehci->sbrn & 0x0f),
 		first ? "initialized" : "restarted",
 		temp >> 8, temp & 0xff, DRIVER_VERSION);
 
@@ -679,188 +562,6 @@ static int ehci_start (struct usb_hcd *hcd)
 	return 0;
 }
 
-/* always called by thread; normally rmmod */
-
-static void ehci_stop (struct usb_hcd *hcd)
-{
-	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
-
-	ehci_dbg (ehci, "stop\n");
-
-	/* Turn off port power on all root hub ports. */
-	ehci_port_power (ehci, 0);
-
-	/* no more interrupts ... */
-	del_timer_sync (&ehci->watchdog);
-
-	spin_lock_irq(&ehci->lock);
-	if (HC_IS_RUNNING (hcd->state))
-		ehci_quiesce (ehci);
-
-	ehci_reset (ehci);
-	writel (0, &ehci->regs->intr_enable);
-	spin_unlock_irq(&ehci->lock);
-
-	/* let companion controllers work when we aren't */
-	writel (0, &ehci->regs->configured_flag);
-	unregister_reboot_notifier (&ehci->reboot_notifier);
-
-	remove_debug_files (ehci);
-
-	/* root hub is shut down separately (first, when possible) */
-	spin_lock_irq (&ehci->lock);
-	if (ehci->async)
-		ehci_work (ehci, NULL);
-	spin_unlock_irq (&ehci->lock);
-	ehci_mem_cleanup (ehci);
-
-#ifdef	EHCI_STATS
-	ehci_dbg (ehci, "irq normal %ld err %ld reclaim %ld (lost %ld)\n",
-		ehci->stats.normal, ehci->stats.error, ehci->stats.reclaim,
-		ehci->stats.lost_iaa);
-	ehci_dbg (ehci, "complete %ld unlink %ld\n",
-		ehci->stats.complete, ehci->stats.unlink);
-#endif
-
-	dbg_status (ehci, "ehci_stop completed", readl (&ehci->regs->status));
-}
-
-static int ehci_get_frame (struct usb_hcd *hcd)
-{
-	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
-	return (readl (&ehci->regs->frame_index) >> 3) % ehci->periodic_size;
-}
-
-/*-------------------------------------------------------------------------*/
-
-#ifdef	CONFIG_PM
-
-/* suspend/resume, section 4.3 */
-
-/* These routines rely on the bus (pci, platform, etc)
- * to handle powerdown and wakeup, and currently also on
- * transceivers that don't need any software attention to set up
- * the right sort of wakeup.  
- */
-
-static int ehci_suspend (struct usb_hcd *hcd, pm_message_t message)
-{
-	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
-
-	if (time_before (jiffies, ehci->next_statechange))
-		msleep (100);
-
-#ifdef	CONFIG_USB_SUSPEND
-	(void) usb_suspend_device (hcd->self.root_hub, message);
-#else
-	usb_lock_device (hcd->self.root_hub);
-	(void) ehci_hub_suspend (hcd);
-	usb_unlock_device (hcd->self.root_hub);
-#endif
-
-	// save (PCI) FLADJ in case of Vaux power loss
-	// ... we'd only use it to handle clock skew
-
-	return 0;
-}
-
-static int ehci_resume (struct usb_hcd *hcd)
-{
-	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
-	unsigned		port;
-	struct usb_device	*root = hcd->self.root_hub;
-	int			retval = -EINVAL;
-
-	// maybe restore (PCI) FLADJ
-
-	if (time_before (jiffies, ehci->next_statechange))
-		msleep (100);
-
-	/* If any port is suspended (or owned by the companion),
-	 * we know we can/must resume the HC (and mustn't reset it).
-	 */
-	for (port = HCS_N_PORTS (ehci->hcs_params); port > 0; ) {
-		u32	status;
-		port--;
-		status = readl (&ehci->regs->port_status [port]);
-		if (!(status & PORT_POWER))
-			continue;
-		if (status & (PORT_SUSPEND | PORT_OWNER)) {
-			down (&hcd->self.root_hub->serialize);
-			retval = ehci_hub_resume (hcd);
-			up (&hcd->self.root_hub->serialize);
-			break;
-		}
-		if (!root->children [port])
-			continue;
-		dbg_port (ehci, __FUNCTION__, port + 1, status);
-		usb_set_device_state (root->children[port],
-					USB_STATE_NOTATTACHED);
-	}
-
-	/* Else reset, to cope with power loss or flush-to-storage
-	 * style "resume" having activated BIOS during reboot.
-	 */
-	if (port == 0) {
-		(void) ehci_halt (ehci);
-		(void) ehci_reset (ehci);
-		(void) ehci_hc_reset (hcd);
-
-		/* emptying the schedule aborts any urbs */
-		spin_lock_irq (&ehci->lock);
-		if (ehci->reclaim)
-			ehci->reclaim_ready = 1;
-		ehci_work (ehci, NULL);
-		spin_unlock_irq (&ehci->lock);
-
-		/* restart; khubd will disconnect devices */
-		retval = ehci_start (hcd);
-
-		/* here we "know" root ports should always stay powered;
-		 * but some controllers may lose all power.
-		 */
-		ehci_port_power (ehci, 1);
-	}
-
-	return retval;
-}
-
-#endif
-
-/*-------------------------------------------------------------------------*/
-
-/*
- * ehci_work is called from some interrupts, timers, and so on.
- * it calls driver completion functions, after dropping ehci->lock.
- */
-static void ehci_work (struct ehci_hcd *ehci, struct pt_regs *regs)
-{
-	timer_action_done (ehci, TIMER_IO_WATCHDOG);
-	if (ehci->reclaim_ready)
-		end_unlink_async (ehci, regs);
-
-	/* another CPU may drop ehci->lock during a schedule scan while
-	 * it reports urb completions.  this flag guards against bogus
-	 * attempts at re-entrant schedule scanning.
-	 */
-	if (ehci->scanning)
-		return;
-	ehci->scanning = 1;
-	scan_async (ehci, regs);
-	if (ehci->next_uframe != -1)
-		scan_periodic (ehci, regs);
-	ehci->scanning = 0;
-
-	/* the IO watchdog guards against hardware or driver bugs that
-	 * misplace IRQs, and should let us run completely without IRQs.
-	 * such lossage has been observed on both VT6202 and VT8235. 
-	 */
-	if (HC_IS_RUNNING (ehci_to_hcd(ehci)->state) &&
-			(ehci->async->qh_next.ptr != NULL ||
-			 ehci->periodic_sched != 0))
-		timer_action (ehci, TIMER_IO_WATCHDOG);
-}
-
 /*-------------------------------------------------------------------------*/
 
 static irqreturn_t ehci_irq (struct usb_hcd *hcd, struct pt_regs *regs)
@@ -1171,106 +872,24 @@ done:
 	return;
 }
 
-/*-------------------------------------------------------------------------*/
-
-static const struct hc_driver ehci_driver = {
-	.description =		hcd_name,
-	.product_desc =		"EHCI Host Controller",
-	.hcd_priv_size =	sizeof(struct ehci_hcd),
-
-	/*
-	 * generic hardware linkage
-	 */
-	.irq =			ehci_irq,
-	.flags =		HCD_MEMORY | HCD_USB2,
-
-	/*
-	 * basic lifecycle operations
-	 */
-	.reset =		ehci_hc_reset,
-	.start =		ehci_start,
-#ifdef	CONFIG_PM
-	.suspend =		ehci_suspend,
-	.resume =		ehci_resume,
-#endif
-	.stop =			ehci_stop,
-
-	/*
-	 * managing i/o requests and associated device resources
-	 */
-	.urb_enqueue =		ehci_urb_enqueue,
-	.urb_dequeue =		ehci_urb_dequeue,
-	.endpoint_disable =	ehci_endpoint_disable,
-
-	/*
-	 * scheduling support
-	 */
-	.get_frame_number =	ehci_get_frame,
-
-	/*
-	 * root hub support
-	 */
-	.hub_status_data =	ehci_hub_status_data,
-	.hub_control =		ehci_hub_control,
-	.hub_suspend =		ehci_hub_suspend,
-	.hub_resume =		ehci_hub_resume,
-};
+static int ehci_get_frame (struct usb_hcd *hcd)
+{
+	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
+	return (readl (&ehci->regs->frame_index) >> 3) % ehci->periodic_size;
+}
 
 /*-------------------------------------------------------------------------*/
 
-/* EHCI 1.0 doesn't require PCI */
-
-#ifdef	CONFIG_PCI
-
-/* PCI driver selection metadata; PCI hotplugging uses this */
-static const struct pci_device_id pci_ids [] = { {
-	/* handle any USB 2.0 EHCI controller */
-	PCI_DEVICE_CLASS(((PCI_CLASS_SERIAL_USB << 8) | 0x20), ~0),
-	.driver_data =	(unsigned long) &ehci_driver,
-	},
-	{ /* end: all zeroes */ }
-};
-MODULE_DEVICE_TABLE (pci, pci_ids);
-
-/* pci driver glue; this is a "new style" PCI driver module */
-static struct pci_driver ehci_pci_driver = {
-	.name =		(char *) hcd_name,
-	.id_table =	pci_ids,
-
-	.probe =	usb_hcd_pci_probe,
-	.remove =	usb_hcd_pci_remove,
-
-#ifdef	CONFIG_PM
-	.suspend =	usb_hcd_pci_suspend,
-	.resume =	usb_hcd_pci_resume,
-#endif
-};
-
-#endif	/* PCI */
-
-
 #define DRIVER_INFO DRIVER_VERSION " " DRIVER_DESC
 
 MODULE_DESCRIPTION (DRIVER_INFO);
 MODULE_AUTHOR (DRIVER_AUTHOR);
 MODULE_LICENSE ("GPL");
 
-static int __init init (void) 
-{
-	if (usb_disabled())
-		return -ENODEV;
-
-	pr_debug ("%s: block sizes: qh %Zd qtd %Zd itd %Zd sitd %Zd\n",
-		hcd_name,
-		sizeof (struct ehci_qh), sizeof (struct ehci_qtd),
-		sizeof (struct ehci_itd), sizeof (struct ehci_sitd));
-
-	return pci_register_driver (&ehci_pci_driver);
-}
-module_init (init);
+#ifdef CONFIG_PCI
+#include "ehci-pci.c"
+#endif
 
-static void __exit cleanup (void) 
-{	
-	pci_unregister_driver (&ehci_pci_driver);
-}
-module_exit (cleanup);
+#if !defined(CONFIG_PCI)
+#error "missing bus glue for ehci-hcd"
+#endif
diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c
index 18d3f2270316..88cb4ada686e 100644
--- a/drivers/usb/host/ehci-hub.c
+++ b/drivers/usb/host/ehci-hub.c
@@ -30,7 +30,7 @@
 
 #ifdef	CONFIG_PM
 
-static int ehci_hub_suspend (struct usb_hcd *hcd)
+static int ehci_bus_suspend (struct usb_hcd *hcd)
 {
 	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
 	int			port;
@@ -83,7 +83,7 @@ static int ehci_hub_suspend (struct usb_hcd *hcd)
 
 
 /* caller has locked the root hub, and should reset/reinit on error */
-static int ehci_hub_resume (struct usb_hcd *hcd)
+static int ehci_bus_resume (struct usb_hcd *hcd)
 {
 	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
 	u32			temp;
@@ -159,8 +159,8 @@ static int ehci_hub_resume (struct usb_hcd *hcd)
 
 #else
 
-#define ehci_hub_suspend	NULL
-#define ehci_hub_resume		NULL
+#define ehci_bus_suspend	NULL
+#define ehci_bus_resume		NULL
 
 #endif	/* CONFIG_PM */
 
diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c
new file mode 100644
index 000000000000..145008853966
--- /dev/null
+++ b/drivers/usb/host/ehci-pci.c
@@ -0,0 +1,415 @@
+/*
+ * EHCI HCD (Host Controller Driver) PCI Bus Glue.
+ *
+ * Copyright (c) 2000-2004 by David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
+ * or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software Foundation,
+ * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef CONFIG_PCI
+#error "This file is PCI bus glue.  CONFIG_PCI must be defined."
+#endif
+
+/*-------------------------------------------------------------------------*/
+
+/* EHCI 0.96 (and later) section 5.1 says how to kick BIOS/SMM/...
+ * off the controller (maybe it can boot from highspeed USB disks).
+ */
+static int bios_handoff (struct ehci_hcd *ehci, int where, u32 cap)
+{
+	struct pci_dev *pdev = to_pci_dev(ehci_to_hcd(ehci)->self.controller);
+
+	/* always say Linux will own the hardware */
+	pci_write_config_byte(pdev, where + 3, 1);
+
+	/* maybe wait a while for BIOS to respond */
+	if (cap & (1 << 16)) {
+		int msec = 5000;
+
+		do {
+			msleep(10);
+			msec -= 10;
+			pci_read_config_dword(pdev, where, &cap);
+		} while ((cap & (1 << 16)) && msec);
+		if (cap & (1 << 16)) {
+			ehci_err(ehci, "BIOS handoff failed (%d, %08x)\n",
+				where, cap);
+			// some BIOS versions seem buggy...
+			// return 1;
+			ehci_warn (ehci, "continuing after BIOS bug...\n");
+			/* disable all SMIs, and clear "BIOS owns" flag */
+			pci_write_config_dword(pdev, where + 4, 0);
+			pci_write_config_byte(pdev, where + 2, 0);
+		} else
+			ehci_dbg(ehci, "BIOS handoff succeeded\n");
+	}
+	return 0;
+}
+
+/* called by khubd or root hub init threads */
+static int ehci_pci_reset (struct usb_hcd *hcd)
+{
+	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
+	u32			temp;
+	unsigned		count = 256/4;
+
+	spin_lock_init (&ehci->lock);
+
+	ehci->caps = hcd->regs;
+	ehci->regs = hcd->regs + HC_LENGTH (readl (&ehci->caps->hc_capbase));
+	dbg_hcs_params (ehci, "reset");
+	dbg_hcc_params (ehci, "reset");
+
+	/* cache this readonly data; minimize chip reads */
+	ehci->hcs_params = readl (&ehci->caps->hcs_params);
+
+	if (hcd->self.controller->bus == &pci_bus_type) {
+		struct pci_dev	*pdev = to_pci_dev(hcd->self.controller);
+
+		switch (pdev->vendor) {
+		case PCI_VENDOR_ID_TDI:
+			if (pdev->device == PCI_DEVICE_ID_TDI_EHCI) {
+				ehci->is_tdi_rh_tt = 1;
+				tdi_reset (ehci);
+			}
+			break;
+		case PCI_VENDOR_ID_AMD:
+			/* AMD8111 EHCI doesn't work, according to AMD errata */
+			if (pdev->device == 0x7463) {
+				ehci_info (ehci, "ignoring AMD8111 (errata)\n");
+				return -EIO;
+			}
+			break;
+		case PCI_VENDOR_ID_NVIDIA:
+			/* NVidia reports that certain chips don't handle
+			 * QH, ITD, or SITD addresses above 2GB.  (But TD,
+			 * data buffer, and periodic schedule are normal.)
+			 */
+			switch (pdev->device) {
+			case 0x003c:	/* MCP04 */
+			case 0x005b:	/* CK804 */
+			case 0x00d8:	/* CK8 */
+			case 0x00e8:	/* CK8S */
+				if (pci_set_consistent_dma_mask(pdev,
+							DMA_31BIT_MASK) < 0)
+					ehci_warn (ehci, "can't enable NVidia "
+						"workaround for >2GB RAM\n");
+				break;
+			}
+			break;
+		}
+
+		/* optional debug port, normally in the first BAR */
+		temp = pci_find_capability (pdev, 0x0a);
+		if (temp) {
+			pci_read_config_dword(pdev, temp, &temp);
+			temp >>= 16;
+			if ((temp & (3 << 13)) == (1 << 13)) {
+				temp &= 0x1fff;
+				ehci->debug = hcd->regs + temp;
+				temp = readl (&ehci->debug->control);
+				ehci_info (ehci, "debug port %d%s\n",
+					HCS_DEBUG_PORT(ehci->hcs_params),
+					(temp & DBGP_ENABLED)
+						? " IN USE"
+						: "");
+				if (!(temp & DBGP_ENABLED))
+					ehci->debug = NULL;
+			}
+		}
+
+		temp = HCC_EXT_CAPS (readl (&ehci->caps->hcc_params));
+	} else
+		temp = 0;
+
+	/* EHCI 0.96 and later may have "extended capabilities" */
+	while (temp && count--) {
+		u32		cap;
+
+		pci_read_config_dword (to_pci_dev(hcd->self.controller),
+				temp, &cap);
+		ehci_dbg (ehci, "capability %04x at %02x\n", cap, temp);
+		switch (cap & 0xff) {
+		case 1:			/* BIOS/SMM/... handoff */
+			if (bios_handoff (ehci, temp, cap) != 0)
+				return -EOPNOTSUPP;
+			break;
+		case 0:			/* illegal reserved capability */
+			ehci_warn (ehci, "illegal capability!\n");
+			cap = 0;
+			/* FALLTHROUGH */
+		default:		/* unknown */
+			break;
+		}
+		temp = (cap >> 8) & 0xff;
+	}
+	if (!count) {
+		ehci_err (ehci, "bogus capabilities ... PCI problems!\n");
+		return -EIO;
+	}
+	if (ehci_is_TDI(ehci))
+		ehci_reset (ehci);
+
+	ehci_port_power (ehci, 0);
+
+	/* at least the Genesys GL880S needs fixup here */
+	temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params);
+	temp &= 0x0f;
+	if (temp && HCS_N_PORTS(ehci->hcs_params) > temp) {
+		ehci_dbg (ehci, "bogus port configuration: "
+			"cc=%d x pcc=%d < ports=%d\n",
+			HCS_N_CC(ehci->hcs_params),
+			HCS_N_PCC(ehci->hcs_params),
+			HCS_N_PORTS(ehci->hcs_params));
+
+		if (hcd->self.controller->bus == &pci_bus_type) {
+			struct pci_dev	*pdev;
+
+			pdev = to_pci_dev(hcd->self.controller);
+			switch (pdev->vendor) {
+			case 0x17a0:		/* GENESYS */
+				/* GL880S: should be PORTS=2 */
+				temp |= (ehci->hcs_params & ~0xf);
+				ehci->hcs_params = temp;
+				break;
+			case PCI_VENDOR_ID_NVIDIA:
+				/* NF4: should be PCC=10 */
+				break;
+			}
+		}
+	}
+
+	/* force HC to halt state */
+	return ehci_halt (ehci);
+}
+
+static int ehci_pci_start (struct usb_hcd *hcd)
+{
+	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
+	int result = 0;
+
+	if (hcd->self.controller->bus == &pci_bus_type) {
+		struct pci_dev		*pdev;
+		u16			port_wake;
+
+		pdev = to_pci_dev(hcd->self.controller);
+
+		/* Serial Bus Release Number is at PCI 0x60 offset */
+		pci_read_config_byte(pdev, 0x60, &ehci->sbrn);
+
+		/* port wake capability, reported by boot firmware */
+		pci_read_config_word(pdev, 0x62, &port_wake);
+		hcd->can_wakeup = (port_wake & 1) != 0;
+
+		/* help hc dma work well with cachelines */
+		result = pci_set_mwi(pdev);
+		if (result)
+			ehci_dbg(ehci, "unable to enable MWI - not fatal.\n");
+	}
+
+	return ehci_run (hcd);
+}
+
+/* always called by thread; normally rmmod */
+
+static void ehci_pci_stop (struct usb_hcd *hcd)
+{
+	ehci_stop (hcd);
+}
+
+/*-------------------------------------------------------------------------*/
+
+#ifdef	CONFIG_PM
+
+/* suspend/resume, section 4.3 */
+
+/* These routines rely on the bus (pci, platform, etc)
+ * to handle powerdown and wakeup, and currently also on
+ * transceivers that don't need any software attention to set up
+ * the right sort of wakeup.
+ */
+
+static int ehci_pci_suspend (struct usb_hcd *hcd, pm_message_t message)
+{
+	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
+
+	if (time_before (jiffies, ehci->next_statechange))
+		msleep (100);
+
+#ifdef	CONFIG_USB_SUSPEND
+	(void) usb_suspend_device (hcd->self.root_hub);
+#else
+	usb_lock_device (hcd->self.root_hub);
+	(void) ehci_bus_suspend (hcd);
+	usb_unlock_device (hcd->self.root_hub);
+#endif
+
+	// save (PCI) FLADJ in case of Vaux power loss
+	// ... we'd only use it to handle clock skew
+
+	return 0;
+}
+
+static int ehci_pci_resume (struct usb_hcd *hcd)
+{
+	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
+	unsigned		port;
+	struct usb_device	*root = hcd->self.root_hub;
+	int			retval = -EINVAL;
+
+	// maybe restore (PCI) FLADJ
+
+	if (time_before (jiffies, ehci->next_statechange))
+		msleep (100);
+
+	/* If any port is suspended (or owned by the companion),
+	 * we know we can/must resume the HC (and mustn't reset it).
+	 */
+	for (port = HCS_N_PORTS (ehci->hcs_params); port > 0; ) {
+		u32	status;
+		port--;
+		status = readl (&ehci->regs->port_status [port]);
+		if (!(status & PORT_POWER))
+			continue;
+		if (status & (PORT_SUSPEND | PORT_OWNER)) {
+			down (&hcd->self.root_hub->serialize);
+			retval = ehci_bus_resume (hcd);
+			up (&hcd->self.root_hub->serialize);
+			break;
+		}
+		if (!root->children [port])
+			continue;
+		dbg_port (ehci, __FUNCTION__, port + 1, status);
+		usb_set_device_state (root->children[port],
+					USB_STATE_NOTATTACHED);
+	}
+
+	/* Else reset, to cope with power loss or flush-to-storage
+	 * style "resume" having activated BIOS during reboot.
+	 */
+	if (port == 0) {
+		(void) ehci_halt (ehci);
+		(void) ehci_reset (ehci);
+		(void) ehci_pci_reset (hcd);
+
+		/* emptying the schedule aborts any urbs */
+		spin_lock_irq (&ehci->lock);
+		if (ehci->reclaim)
+			ehci->reclaim_ready = 1;
+		ehci_work (ehci, NULL);
+		spin_unlock_irq (&ehci->lock);
+
+		/* restart; khubd will disconnect devices */
+		retval = ehci_run (hcd);
+
+		/* here we "know" root ports should always stay powered;
+		 * but some controllers may lose all power.
+		 */
+		ehci_port_power (ehci, 1);
+	}
+
+	return retval;
+}
+#endif
+
+static const struct hc_driver ehci_pci_hc_driver = {
+	.description =		hcd_name,
+	.product_desc =		"EHCI Host Controller",
+	.hcd_priv_size =	sizeof(struct ehci_hcd),
+
+	/*
+	 * generic hardware linkage
+	 */
+	.irq =			ehci_irq,
+	.flags =		HCD_MEMORY | HCD_USB2,
+
+	/*
+	 * basic lifecycle operations
+	 */
+	.reset =		ehci_pci_reset,
+	.start =		ehci_pci_start,
+#ifdef	CONFIG_PM
+	.suspend =		ehci_pci_suspend,
+	.resume =		ehci_pci_resume,
+#endif
+	.stop =			ehci_pci_stop,
+
+	/*
+	 * managing i/o requests and associated device resources
+	 */
+	.urb_enqueue =		ehci_urb_enqueue,
+	.urb_dequeue =		ehci_urb_dequeue,
+	.endpoint_disable =	ehci_endpoint_disable,
+
+	/*
+	 * scheduling support
+	 */
+	.get_frame_number =	ehci_get_frame,
+
+	/*
+	 * root hub support
+	 */
+	.hub_status_data =	ehci_hub_status_data,
+	.hub_control =		ehci_hub_control,
+	.bus_suspend =		ehci_bus_suspend,
+	.bus_resume =		ehci_bus_resume,
+};
+
+/*-------------------------------------------------------------------------*/
+
+/* PCI driver selection metadata; PCI hotplugging uses this */
+static const struct pci_device_id pci_ids [] = { {
+	/* handle any USB 2.0 EHCI controller */
+	PCI_DEVICE_CLASS(((PCI_CLASS_SERIAL_USB << 8) | 0x20), ~0),
+	.driver_data =	(unsigned long) &ehci_pci_hc_driver,
+	},
+	{ /* end: all zeroes */ }
+};
+MODULE_DEVICE_TABLE (pci, pci_ids);
+
+/* pci driver glue; this is a "new style" PCI driver module */
+static struct pci_driver ehci_pci_driver = {
+	.name =		(char *) hcd_name,
+	.id_table =	pci_ids,
+	.owner = 	THIS_MODULE,
+
+	.probe =	usb_hcd_pci_probe,
+	.remove =	usb_hcd_pci_remove,
+
+#ifdef	CONFIG_PM
+	.suspend =	usb_hcd_pci_suspend,
+	.resume =	usb_hcd_pci_resume,
+#endif
+};
+
+static int __init ehci_hcd_pci_init (void)
+{
+	if (usb_disabled())
+		return -ENODEV;
+
+	pr_debug ("%s: block sizes: qh %Zd qtd %Zd itd %Zd sitd %Zd\n",
+		hcd_name,
+		sizeof (struct ehci_qh), sizeof (struct ehci_qtd),
+		sizeof (struct ehci_itd), sizeof (struct ehci_sitd));
+
+	return pci_register_driver (&ehci_pci_driver);
+}
+module_init (ehci_hcd_pci_init);
+
+static void __exit ehci_hcd_pci_cleanup (void)
+{
+	pci_unregister_driver (&ehci_pci_driver);
+}
+module_exit (ehci_hcd_pci_cleanup);
diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h
index f34a0516d35f..18e257c2bdb5 100644
--- a/drivers/usb/host/ehci.h
+++ b/drivers/usb/host/ehci.h
@@ -97,6 +97,7 @@ struct ehci_hcd {			/* one per controller */
 #else
 #	define COUNT(x) do {} while (0)
 #endif
+	u8			sbrn;		/* packed release number */
 };
 
 /* convert between an HCD pointer and the corresponding EHCI_HCD */ 
diff --git a/drivers/usb/host/isp116x-hcd.c b/drivers/usb/host/isp116x-hcd.c
index 642f35068ce2..ddb8fc591466 100644
--- a/drivers/usb/host/isp116x-hcd.c
+++ b/drivers/usb/host/isp116x-hcd.c
@@ -638,7 +638,7 @@ static irqreturn_t isp116x_irq(struct usb_hcd *hcd, struct pt_regs *regs)
 				  + msecs_to_jiffies(20) + 1);
 		if (intstat & HCINT_RD) {
 			DBG("---- remote wakeup\n");
-			schedule_work(&isp116x->rh_resume);
+			usb_hcd_resume_root_hub(hcd);
 			ret = IRQ_HANDLED;
 		}
 		irqstat &= ~HCuPINT_OPR;
@@ -1160,7 +1160,7 @@ static int isp116x_hub_control(struct usb_hcd *hcd,
 
 #ifdef	CONFIG_PM
 
-static int isp116x_hub_suspend(struct usb_hcd *hcd)
+static int isp116x_bus_suspend(struct usb_hcd *hcd)
 {
 	struct isp116x *isp116x = hcd_to_isp116x(hcd);
 	unsigned long flags;
@@ -1200,7 +1200,7 @@ static int isp116x_hub_suspend(struct usb_hcd *hcd)
 	return ret;
 }
 
-static int isp116x_hub_resume(struct usb_hcd *hcd)
+static int isp116x_bus_resume(struct usb_hcd *hcd)
 {
 	struct isp116x *isp116x = hcd_to_isp116x(hcd);
 	u32 val;
@@ -1263,21 +1263,11 @@ static int isp116x_hub_resume(struct usb_hcd *hcd)
 	return 0;
 }
 
-static void isp116x_rh_resume(void *_hcd)
-{
-	struct usb_hcd *hcd = _hcd;
-
-	usb_resume_device(hcd->self.root_hub);
-}
 
 #else
 
-#define	isp116x_hub_suspend	NULL
-#define	isp116x_hub_resume	NULL
-
-static void isp116x_rh_resume(void *_hcd)
-{
-}
+#define	isp116x_bus_suspend	NULL
+#define	isp116x_bus_resume	NULL
 
 #endif
 
@@ -1636,8 +1626,8 @@ static struct hc_driver isp116x_hc_driver = {
 
 	.hub_status_data = isp116x_hub_status_data,
 	.hub_control = isp116x_hub_control,
-	.hub_suspend = isp116x_hub_suspend,
-	.hub_resume = isp116x_hub_resume,
+	.bus_suspend = isp116x_bus_suspend,
+	.bus_resume = isp116x_bus_resume,
 };
 
 /*----------------------------------------------------------------*/
@@ -1732,7 +1722,6 @@ static int __init isp116x_probe(struct device *dev)
 	isp116x->addr_reg = addr_reg;
 	spin_lock_init(&isp116x->lock);
 	INIT_LIST_HEAD(&isp116x->async);
-	INIT_WORK(&isp116x->rh_resume, isp116x_rh_resume, hcd);
 	isp116x->board = dev->platform_data;
 
 	if (!isp116x->board) {
@@ -1777,16 +1766,10 @@ static int __init isp116x_probe(struct device *dev)
 static int isp116x_suspend(struct device *dev, pm_message_t state)
 {
 	int ret = 0;
-	struct usb_hcd *hcd = dev_get_drvdata(dev);
 
 	VDBG("%s: state %x\n", __func__, state);
 
-	ret = usb_suspend_device(hcd->self.root_hub, state);
-	if (!ret) {
-		dev->power.power_state = state;
-		INFO("%s suspended\n", hcd_name);
-	} else
-		ERR("%s suspend failed\n", hcd_name);
+	dev->power.power_state = state;
 
 	return ret;
 }
@@ -1797,15 +1780,11 @@ static int isp116x_suspend(struct device *dev, pm_message_t state)
 static int isp116x_resume(struct device *dev)
 {
 	int ret = 0;
-	struct usb_hcd *hcd = dev_get_drvdata(dev);
 
 	VDBG("%s:  state %x\n", __func__, dev->power.power_state);
 
-	ret = usb_resume_device(hcd->self.root_hub);
-	if (!ret) {
-		dev->power.power_state = PMSG_ON;
-		VDBG("%s resumed\n", (char *)hcd_name);
-	}
+	dev->power.power_state = PMSG_ON;
+
 	return ret;
 }
 
diff --git a/drivers/usb/host/isp116x.h b/drivers/usb/host/isp116x.h
index 58873470dcf5..c6fec96785fe 100644
--- a/drivers/usb/host/isp116x.h
+++ b/drivers/usb/host/isp116x.h
@@ -253,7 +253,6 @@ static const int cc_to_error[16] = {
 
 struct isp116x {
 	spinlock_t lock;
-	struct work_struct rh_resume;
 
 	void __iomem *addr_reg;
 	void __iomem *data_reg;
diff --git a/drivers/usb/host/ohci-au1xxx.c b/drivers/usb/host/ohci-au1xxx.c
index 3981bf15c8c7..a277e258eb6c 100644
--- a/drivers/usb/host/ohci-au1xxx.c
+++ b/drivers/usb/host/ohci-au1xxx.c
@@ -214,6 +214,11 @@ static const struct hc_driver ohci_au1xxx_hc_driver = {
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
+#ifdef	CONFIG_PM
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
+#endif
+	.start_port_reset =	ohci_start_port_reset,
 };
 
 /*-------------------------------------------------------------------------*/
@@ -259,6 +264,7 @@ static int ohci_hcd_au1xxx_drv_resume(struct device *dev)
 
 static struct device_driver ohci_hcd_au1xxx_driver = {
 	.name		= "au1xxx-ohci",
+	.owner		= THIS_MODULE,
 	.bus		= &platform_bus_type,
 	.probe		= ohci_hcd_au1xxx_drv_probe,
 	.remove		= ohci_hcd_au1xxx_drv_remove,
diff --git a/drivers/usb/host/ohci-dbg.c b/drivers/usb/host/ohci-dbg.c
index 7924c74f958e..7bfffcbbd226 100644
--- a/drivers/usb/host/ohci-dbg.c
+++ b/drivers/usb/host/ohci-dbg.c
@@ -193,10 +193,6 @@ ohci_dump_status (struct ohci_hcd *controller, char **next, unsigned *size)
 
 	maybe_print_eds (controller, "donehead",
 			ohci_readl (controller, &regs->donehead), next, size);
-
-	/* broken fminterval means traffic won't flow! */ 
-	ohci_dbg (controller, "fminterval %08x\n", 
-			ohci_readl (controller, &regs->fminterval));
 }
 
 #define dbg_port_sw(hc,num,value,next,size) \
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index f8da8c7af7c6..5c0c6c8a7a82 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -723,7 +723,7 @@ static irqreturn_t ohci_irq (struct usb_hcd *hcd, struct pt_regs *ptregs)
 		ohci_vdbg (ohci, "resume detect\n");
 		ohci_writel (ohci, OHCI_INTR_RD, &regs->intrstatus);
 		if (hcd->state != HC_STATE_QUIESCING)
-			schedule_work(&ohci->rh_resume);
+			usb_hcd_resume_root_hub(hcd);
 	}
 
 	if (ints & OHCI_INTR_WDH) {
@@ -791,7 +791,7 @@ static void ohci_stop (struct usb_hcd *hcd)
 
 /* must not be called from interrupt context */
 
-#if	defined(CONFIG_USB_SUSPEND) || defined(CONFIG_PM)
+#ifdef	CONFIG_PM
 
 static int ohci_restart (struct ohci_hcd *ohci)
 {
diff --git a/drivers/usb/host/ohci-hub.c b/drivers/usb/host/ohci-hub.c
index ce7b28da7a15..e01e77bc324b 100644
--- a/drivers/usb/host/ohci-hub.c
+++ b/drivers/usb/host/ohci-hub.c
@@ -36,7 +36,7 @@
 
 /*-------------------------------------------------------------------------*/
 
-#if	defined(CONFIG_USB_SUSPEND) || defined(CONFIG_PM)
+#ifdef	CONFIG_PM
 
 #define OHCI_SCHED_ENABLES \
 	(OHCI_CTRL_CLE|OHCI_CTRL_BLE|OHCI_CTRL_PLE|OHCI_CTRL_IE)
@@ -45,7 +45,7 @@ static void dl_done_list (struct ohci_hcd *, struct pt_regs *);
 static void finish_unlinks (struct ohci_hcd *, u16 , struct pt_regs *);
 static int ohci_restart (struct ohci_hcd *ohci);
 
-static int ohci_hub_suspend (struct usb_hcd *hcd)
+static int ohci_bus_suspend (struct usb_hcd *hcd)
 {
 	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
 	int			status = 0;
@@ -73,7 +73,6 @@ static int ohci_hub_suspend (struct usb_hcd *hcd)
 	ohci_dbg (ohci, "suspend root hub\n");
 
 	/* First stop any processing */
-	hcd->state = HC_STATE_QUIESCING;
 	if (ohci->hc_control & OHCI_SCHED_ENABLES) {
 		int		limit;
 
@@ -108,7 +107,9 @@ static int ohci_hub_suspend (struct usb_hcd *hcd)
 	else
 		ohci->hc_control &= ~OHCI_CTRL_RWE;
 
-	/* Suspend hub */
+	/* Suspend hub ... this is the "global (to this bus) suspend" mode,
+	 * which doesn't imply ports will first be individually suspended.
+	 */
 	ohci->hc_control &= ~OHCI_CTRL_HCFS;
 	ohci->hc_control |= OHCI_USB_SUSPEND;
 	ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
@@ -118,8 +119,9 @@ static int ohci_hub_suspend (struct usb_hcd *hcd)
 	ohci->next_statechange = jiffies + msecs_to_jiffies (5);
 
 done:
+	/* external suspend vs self autosuspend ... same effect */
 	if (status == 0)
-		hcd->state = HC_STATE_SUSPENDED;
+		usb_hcd_suspend_root_hub(hcd);
 	spin_unlock_irqrestore (&ohci->lock, flags);
 	return status;
 }
@@ -133,7 +135,7 @@ static inline struct ed *find_head (struct ed *ed)
 }
 
 /* caller has locked the root hub */
-static int ohci_hub_resume (struct usb_hcd *hcd)
+static int ohci_bus_resume (struct usb_hcd *hcd)
 {
 	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
 	u32			temp, enables;
@@ -146,7 +148,7 @@ static int ohci_hub_resume (struct usb_hcd *hcd)
 	ohci->hc_control = ohci_readl (ohci, &ohci->regs->control);
 
 	if (ohci->hc_control & (OHCI_CTRL_IR | OHCI_SCHED_ENABLES)) {
-		/* this can happen after suspend-to-disk */
+		/* this can happen after resuming a swsusp snapshot */
 		if (hcd->state == HC_STATE_RESUMING) {
 			ohci_dbg (ohci, "BIOS/SMM active, control %03x\n",
 					ohci->hc_control);
@@ -169,11 +171,12 @@ static int ohci_hub_resume (struct usb_hcd *hcd)
 		ohci_info (ohci, "wakeup\n");
 		break;
 	case OHCI_USB_OPER:
-		ohci_dbg (ohci, "already resumed\n");
-		status = 0;
+		/* this can happen after resuming a swsusp snapshot */
+		ohci_dbg (ohci, "snapshot resume? reinit\n");
+		status = -EBUSY;
 		break;
 	default:		/* RESET, we lost power */
-		ohci_dbg (ohci, "root hub hardware reset\n");
+		ohci_dbg (ohci, "lost power\n");
 		status = -EBUSY;
 	}
 	spin_unlock_irq (&ohci->lock);
@@ -198,8 +201,7 @@ static int ohci_hub_resume (struct usb_hcd *hcd)
 	}
 
 	/* Some controllers (lucent erratum) need extra-long delays */
-	hcd->state = HC_STATE_RESUMING;
-	mdelay (20 /* usb 11.5.1.10 */ + 15);
+	msleep (20 /* usb 11.5.1.10 */ + 12 /* 32 msec counter */ + 1);
 
 	temp = ohci_readl (ohci, &ohci->regs->control);
 	temp &= OHCI_CTRL_HCFS;
@@ -273,28 +275,10 @@ static int ohci_hub_resume (struct usb_hcd *hcd)
 		(void) ohci_readl (ohci, &ohci->regs->control);
 	}
 
-	hcd->state = HC_STATE_RUNNING;
 	return 0;
 }
 
-static void ohci_rh_resume (void *_hcd)
-{
-	struct usb_hcd	*hcd = _hcd;
-
-	usb_lock_device (hcd->self.root_hub);
-	(void) ohci_hub_resume (hcd);
-	usb_unlock_device (hcd->self.root_hub);
-}
-
-#else
-
-static void ohci_rh_resume (void *_hcd)
-{
-	struct ohci_hcd	*ohci = hcd_to_ohci (_hcd);
-	ohci_dbg(ohci, "rh_resume ??\n");
-}
-
-#endif	/* CONFIG_USB_SUSPEND || CONFIG_PM */
+#endif	/* CONFIG_PM */
 
 /*-------------------------------------------------------------------------*/
 
@@ -367,7 +351,6 @@ done:
 #ifdef CONFIG_PM
 	/* save power by suspending idle root hubs;
 	 * INTR_RD wakes us when there's work
-	 * NOTE: if we can do this, we don't need a root hub timer!
 	 */
 	if (can_suspend
 			&& !changed
@@ -379,8 +362,7 @@ done:
 			&& usb_trylock_device (hcd->self.root_hub)
 			) {
 		ohci_vdbg (ohci, "autosuspend\n");
-		(void) ohci_hub_suspend (hcd);
-		hcd->state = HC_STATE_RUNNING;
+		(void) ohci_bus_suspend (hcd);
 		usb_unlock_device (hcd->self.root_hub);
 	}
 #endif
@@ -554,7 +536,7 @@ static int ohci_hub_control (
 			temp = RH_PS_POCI;
 			if ((ohci->hc_control & OHCI_CTRL_HCFS)
 					!= OHCI_USB_OPER)
-				schedule_work (&ohci->rh_resume);
+				usb_hcd_resume_root_hub(hcd);
 			break;
 		case USB_PORT_FEAT_C_SUSPEND:
 			temp = RH_PS_PSSC;
diff --git a/drivers/usb/host/ohci-lh7a404.c b/drivers/usb/host/ohci-lh7a404.c
index 859aca7be753..238fa4ade615 100644
--- a/drivers/usb/host/ohci-lh7a404.c
+++ b/drivers/usb/host/ohci-lh7a404.c
@@ -193,6 +193,11 @@ static const struct hc_driver ohci_lh7a404_hc_driver = {
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
+#ifdef	CONFIG_PM
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
+#endif
+	.start_port_reset =	ohci_start_port_reset,
 };
 
 /*-------------------------------------------------------------------------*/
@@ -239,6 +244,7 @@ static int ohci_hcd_lh7a404_drv_resume(struct device *dev)
 
 static struct device_driver ohci_hcd_lh7a404_driver = {
 	.name		= "lh7a404-ohci",
+	.owner		= THIS_MODULE,
 	.bus		= &platform_bus_type,
 	.probe		= ohci_hcd_lh7a404_drv_probe,
 	.remove		= ohci_hcd_lh7a404_drv_remove,
diff --git a/drivers/usb/host/ohci-mem.c b/drivers/usb/host/ohci-mem.c
index 9fb83dfb1eb4..bfbe328a4788 100644
--- a/drivers/usb/host/ohci-mem.c
+++ b/drivers/usb/host/ohci-mem.c
@@ -28,7 +28,6 @@ static void ohci_hcd_init (struct ohci_hcd *ohci)
 	ohci->next_statechange = jiffies;
 	spin_lock_init (&ohci->lock);
 	INIT_LIST_HEAD (&ohci->pending);
-	INIT_WORK (&ohci->rh_resume, ohci_rh_resume, ohci_to_hcd(ohci));
 	ohci->reboot_notifier.notifier_call = ohci_reboot;
 }
 
diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c
index a574216625a0..45efeed1fcc3 100644
--- a/drivers/usb/host/ohci-omap.c
+++ b/drivers/usb/host/ohci-omap.c
@@ -420,9 +420,9 @@ static const struct hc_driver ohci_omap_hc_driver = {
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
-#ifdef	CONFIG_USB_SUSPEND
-	.hub_suspend =		ohci_hub_suspend,
-	.hub_resume =		ohci_hub_resume,
+#ifdef	CONFIG_PM
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
 #endif
 	.start_port_reset =	ohci_start_port_reset,
 };
@@ -458,41 +458,29 @@ static int ohci_hcd_omap_drv_remove(struct device *dev)
 static int ohci_omap_suspend(struct device *dev, pm_message_t message)
 {
 	struct ohci_hcd	*ohci = hcd_to_ohci(dev_get_drvdata(dev));
-	int		status = -EINVAL;
-
-	down(&ohci_to_hcd(ohci)->self.root_hub->serialize);
-	status = ohci_hub_suspend(ohci_to_hcd(ohci));
-	if (status == 0) {
-		omap_ohci_clock_power(0);
-		ohci_to_hcd(ohci)->self.root_hub->state =
-			USB_STATE_SUSPENDED;
-		ohci_to_hcd(ohci)->state = HC_STATE_SUSPENDED;
-		dev->power.power_state = PMSG_SUSPEND;
-	}
-	up(&ohci_to_hcd(ohci)->self.root_hub->serialize);
-	return status;
+
+	if (time_before(jiffies, ohci->next_statechange))
+		msleep(5);
+	ohci->next_statechange = jiffies;
+
+	omap_ohci_clock_power(0);
+	ohci_to_hcd(ohci)->state = HC_STATE_SUSPENDED;
+	dev->power.power_state = PMSG_SUSPEND;
+	return 0;
 }
 
 static int ohci_omap_resume(struct device *dev)
 {
 	struct ohci_hcd	*ohci = hcd_to_ohci(dev_get_drvdata(dev));
-	int		status = 0;
 
 	if (time_before(jiffies, ohci->next_statechange))
 		msleep(5);
 	ohci->next_statechange = jiffies;
+
 	omap_ohci_clock_power(1);
-#ifdef	CONFIG_USB_SUSPEND
-	/* get extra cleanup even if remote wakeup isn't in use */
-	status = usb_resume_device(ohci_to_hcd(ohci)->self.root_hub);
-#else
-	down(&ohci_to_hcd(ohci)->self.root_hub->serialize);
-	status = ohci_hub_resume(ohci_to_hcd(ohci));
-	up(&ohci_to_hcd(ohci)->self.root_hub->serialize);
-#endif
-	if (status == 0)
-		dev->power.power_state = PMSG_ON;
-	return status;
+	dev->power.power_state = PMSG_ON;
+	usb_hcd_resume_root_hub(dev_get_drvdata(dev));
+	return 0;
 }
 
 #endif
@@ -504,6 +492,7 @@ static int ohci_omap_resume(struct device *dev)
  */
 static struct device_driver ohci_hcd_omap_driver = {
 	.name		= "ohci",
+	.owner		= THIS_MODULE,
 	.bus		= &platform_bus_type,
 	.probe		= ohci_hcd_omap_drv_probe,
 	.remove		= ohci_hcd_omap_drv_remove,
diff --git a/drivers/usb/host/ohci-pci.c b/drivers/usb/host/ohci-pci.c
index eede6be098d2..bf1d5ab4aa3a 100644
--- a/drivers/usb/host/ohci-pci.c
+++ b/drivers/usb/host/ohci-pci.c
@@ -112,23 +112,13 @@ ohci_pci_start (struct usb_hcd *hcd)
 
 static int ohci_pci_suspend (struct usb_hcd *hcd, pm_message_t message)
 {
-	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
-
-	/* suspend root hub, hoping it keeps power during suspend */
-	if (time_before (jiffies, ohci->next_statechange))
-		msleep (100);
-
-#ifdef	CONFIG_USB_SUSPEND
-	(void) usb_suspend_device (hcd->self.root_hub, message);
-#else
-	usb_lock_device (hcd->self.root_hub);
-	(void) ohci_hub_suspend (hcd);
-	usb_unlock_device (hcd->self.root_hub);
-#endif
+	/* root hub was already suspended */
 
-	/* let things settle down a bit */
-	msleep (100);
-	
+	/* FIXME these PMAC things get called in the wrong places.  ASIC
+	 * clocks should be turned off AFTER entering D3, and on BEFORE
+	 * trying to enter D0.  Evidently the PCI layer doesn't currently
+	 * provide the right sort of platform hooks for this ...
+	 */
 #ifdef CONFIG_PPC_PMAC
 	if (_machine == _MACH_Pmac) {
 	   	struct device_node	*of_node;
@@ -145,9 +135,6 @@ static int ohci_pci_suspend (struct usb_hcd *hcd, pm_message_t message)
 
 static int ohci_pci_resume (struct usb_hcd *hcd)
 {
-	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
-	int			retval = 0;
-
 #ifdef CONFIG_PPC_PMAC
 	if (_machine == _MACH_Pmac) {
 		struct device_node *of_node;
@@ -159,19 +146,8 @@ static int ohci_pci_resume (struct usb_hcd *hcd)
 	}
 #endif /* CONFIG_PPC_PMAC */
 
-	/* resume root hub */
-	if (time_before (jiffies, ohci->next_statechange))
-		msleep (100);
-#ifdef	CONFIG_USB_SUSPEND
-	/* get extra cleanup even if remote wakeup isn't in use */
-	retval = usb_resume_device (hcd->self.root_hub);
-#else
-	usb_lock_device (hcd->self.root_hub);
-	retval = ohci_hub_resume (hcd);
-	usb_unlock_device (hcd->self.root_hub);
-#endif
-
-	return retval;
+	usb_hcd_resume_root_hub(hcd);
+	return 0;
 }
 
 #endif	/* CONFIG_PM */
@@ -218,9 +194,9 @@ static const struct hc_driver ohci_pci_hc_driver = {
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
-#ifdef	CONFIG_USB_SUSPEND
-	.hub_suspend =		ohci_hub_suspend,
-	.hub_resume =		ohci_hub_resume,
+#ifdef	CONFIG_PM
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
 #endif
 	.start_port_reset =	ohci_start_port_reset,
 };
@@ -240,6 +216,7 @@ MODULE_DEVICE_TABLE (pci, pci_ids);
 static struct pci_driver ohci_pci_driver = {
 	.name =		(char *) hcd_name,
 	.id_table =	pci_ids,
+	.owner =	THIS_MODULE,
 
 	.probe =	usb_hcd_pci_probe,
 	.remove =	usb_hcd_pci_remove,
diff --git a/drivers/usb/host/ohci-ppc-soc.c b/drivers/usb/host/ohci-ppc-soc.c
index 251533363028..4832e57ae579 100644
--- a/drivers/usb/host/ohci-ppc-soc.c
+++ b/drivers/usb/host/ohci-ppc-soc.c
@@ -163,9 +163,9 @@ static const struct hc_driver ohci_ppc_soc_hc_driver = {
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
-#ifdef	CONFIG_USB_SUSPEND
-	.hub_suspend =		ohci_hub_suspend,
-	.hub_resume =		ohci_hub_resume,
+#ifdef	CONFIG_PM
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
 #endif
 	.start_port_reset =	ohci_start_port_reset,
 };
@@ -193,10 +193,11 @@ static int ohci_hcd_ppc_soc_drv_remove(struct device *dev)
 
 static struct device_driver ohci_hcd_ppc_soc_driver = {
 	.name		= "ppc-soc-ohci",
+	.owner		= THIS_MODULE,
 	.bus		= &platform_bus_type,
 	.probe		= ohci_hcd_ppc_soc_drv_probe,
 	.remove		= ohci_hcd_ppc_soc_drv_remove,
-#if	defined(CONFIG_USB_SUSPEND) || defined(CONFIG_PM)
+#ifdef	CONFIG_PM
 	/*.suspend	= ohci_hcd_ppc_soc_drv_suspend,*/
 	/*.resume	= ohci_hcd_ppc_soc_drv_resume,*/
 #endif
diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
index f042261ecb8e..d287dcccd415 100644
--- a/drivers/usb/host/ohci-pxa27x.c
+++ b/drivers/usb/host/ohci-pxa27x.c
@@ -278,10 +278,11 @@ static const struct hc_driver ohci_pxa27x_hc_driver = {
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
-#ifdef  CONFIG_USB_SUSPEND
-	.hub_suspend =		ohci_hub_suspend,
-	.hub_resume =		ohci_hub_resume,
+#ifdef  CONFIG_PM
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
 #endif
+	.start_port_reset =	ohci_start_port_reset,
 };
 
 /*-------------------------------------------------------------------------*/
diff --git a/drivers/usb/host/ohci-s3c2410.c b/drivers/usb/host/ohci-s3c2410.c
index da7d5478f74d..fab420a2ce71 100644
--- a/drivers/usb/host/ohci-s3c2410.c
+++ b/drivers/usb/host/ohci-s3c2410.c
@@ -448,11 +448,11 @@ static const struct hc_driver ohci_s3c2410_hc_driver = {
 	 */
 	.hub_status_data =	ohci_s3c2410_hub_status_data,
 	.hub_control =		ohci_s3c2410_hub_control,
-
-#if defined(CONFIG_USB_SUSPEND) && 0
-	.hub_suspend =		ohci_hub_suspend,
-	.hub_resume =		ohci_hub_resume,
+#ifdef	CONFIG_PM
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
 #endif
+	.start_port_reset =	ohci_start_port_reset,
 };
 
 /* device driver */
@@ -474,6 +474,7 @@ static int ohci_hcd_s3c2410_drv_remove(struct device *dev)
 
 static struct device_driver ohci_hcd_s3c2410_driver = {
 	.name		= "s3c2410-ohci",
+	.owner		= THIS_MODULE,
 	.bus		= &platform_bus_type,
 	.probe		= ohci_hcd_s3c2410_drv_probe,
 	.remove		= ohci_hcd_s3c2410_drv_remove,
diff --git a/drivers/usb/host/ohci-sa1111.c b/drivers/usb/host/ohci-sa1111.c
index 814d2be4ee7b..fb3221ebbb29 100644
--- a/drivers/usb/host/ohci-sa1111.c
+++ b/drivers/usb/host/ohci-sa1111.c
@@ -235,10 +235,11 @@ static const struct hc_driver ohci_sa1111_hc_driver = {
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
-#ifdef	CONFIG_USB_SUSPEND
-	.hub_suspend =		ohci_hub_suspend,
-	.hub_resume =		ohci_hub_resume,
+#ifdef	CONFIG_PM
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
 #endif
+	.start_port_reset =	ohci_start_port_reset,
 };
 
 /*-------------------------------------------------------------------------*/
diff --git a/drivers/usb/host/ohci.h b/drivers/usb/host/ohci.h
index 8a9b9d9209e9..caacf14371f5 100644
--- a/drivers/usb/host/ohci.h
+++ b/drivers/usb/host/ohci.h
@@ -389,7 +389,6 @@ struct ohci_hcd {
 	unsigned long		next_statechange;	/* suspend/resume */
 	u32			fminterval;		/* saved register */
 
-	struct work_struct	rh_resume;
 	struct notifier_block	reboot_notifier;
 
 	unsigned long		flags;		/* for HC bugs */
diff --git a/drivers/usb/host/pci-quirks.c b/drivers/usb/host/pci-quirks.c
new file mode 100644
index 000000000000..b7fd3f644e1e
--- /dev/null
+++ b/drivers/usb/host/pci-quirks.c
@@ -0,0 +1,296 @@
+/*
+ * This file contains code to reset and initialize USB host controllers.
+ * Some of it includes work-arounds for PCI hardware and BIOS quirks.
+ * It may need to run early during booting -- before USB would normally
+ * initialize -- to ensure that Linux doesn't use any legacy modes.
+ *
+ *  Copyright (c) 1999 Martin Mares <mj@ucw.cz>
+ *  (and others)
+ */
+
+#include <linux/config.h>
+#ifdef CONFIG_USB_DEBUG
+#define DEBUG
+#else
+#undef DEBUG
+#endif
+
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/acpi.h>
+
+
+#define UHCI_USBLEGSUP		0xc0		/* legacy support */
+#define UHCI_USBCMD		0		/* command register */
+#define UHCI_USBINTR		4		/* interrupt register */
+#define UHCI_USBLEGSUP_RWC	0x8f00		/* the R/WC bits */
+#define UHCI_USBLEGSUP_RO	0x5040		/* R/O and reserved bits */
+#define UHCI_USBCMD_RUN		0x0001		/* RUN/STOP bit */
+#define UHCI_USBCMD_HCRESET	0x0002		/* Host Controller reset */
+#define UHCI_USBCMD_EGSM	0x0008		/* Global Suspend Mode */
+#define UHCI_USBCMD_CONFIGURE	0x0040		/* Config Flag */
+#define UHCI_USBINTR_RESUME	0x0002		/* Resume interrupt enable */
+
+#define OHCI_CONTROL		0x04
+#define OHCI_CMDSTATUS		0x08
+#define OHCI_INTRSTATUS		0x0c
+#define OHCI_INTRENABLE		0x10
+#define OHCI_INTRDISABLE	0x14
+#define OHCI_OCR		(1 << 3)	/* ownership change request */
+#define OHCI_CTRL_RWC		(1 << 9)	/* remote wakeup connected */
+#define OHCI_CTRL_IR		(1 << 8)	/* interrupt routing */
+#define OHCI_INTR_OC		(1 << 30)	/* ownership change */
+
+#define EHCI_HCC_PARAMS		0x08		/* extended capabilities */
+#define EHCI_USBCMD		0		/* command register */
+#define EHCI_USBCMD_RUN		(1 << 0)	/* RUN/STOP bit */
+#define EHCI_USBSTS		4		/* status register */
+#define EHCI_USBSTS_HALTED	(1 << 12)	/* HCHalted bit */
+#define EHCI_USBINTR		8		/* interrupt register */
+#define EHCI_USBLEGSUP		0		/* legacy support register */
+#define EHCI_USBLEGSUP_BIOS	(1 << 16)	/* BIOS semaphore */
+#define EHCI_USBLEGSUP_OS	(1 << 24)	/* OS semaphore */
+#define EHCI_USBLEGCTLSTS	4		/* legacy control/status */
+#define EHCI_USBLEGCTLSTS_SOOE	(1 << 13)	/* SMI on ownership change */
+
+
+/*
+ * Make sure the controller is completely inactive, unable to
+ * generate interrupts or do DMA.
+ */
+void uhci_reset_hc(struct pci_dev *pdev, unsigned long base)
+{
+	/* Turn off PIRQ enable and SMI enable.  (This also turns off the
+	 * BIOS's USB Legacy Support.)  Turn off all the R/WC bits too.
+	 */
+	pci_write_config_word(pdev, UHCI_USBLEGSUP, UHCI_USBLEGSUP_RWC);
+
+	/* Reset the HC - this will force us to get a
+	 * new notification of any already connected
+	 * ports due to the virtual disconnect that it
+	 * implies.
+	 */
+	outw(UHCI_USBCMD_HCRESET, base + UHCI_USBCMD);
+	mb();
+	udelay(5);
+	if (inw(base + UHCI_USBCMD) & UHCI_USBCMD_HCRESET)
+		dev_warn(&pdev->dev, "HCRESET not completed yet!\n");
+
+	/* Just to be safe, disable interrupt requests and
+	 * make sure the controller is stopped.
+	 */
+	outw(0, base + UHCI_USBINTR);
+	outw(0, base + UHCI_USBCMD);
+}
+EXPORT_SYMBOL_GPL(uhci_reset_hc);
+
+/*
+ * Initialize a controller that was newly discovered or has just been
+ * resumed.  In either case we can't be sure of its previous state.
+ *
+ * Returns: 1 if the controller was reset, 0 otherwise.
+ */
+int uhci_check_and_reset_hc(struct pci_dev *pdev, unsigned long base)
+{
+	u16 legsup;
+	unsigned int cmd, intr;
+
+	/*
+	 * When restarting a suspended controller, we expect all the
+	 * settings to be the same as we left them:
+	 *
+	 *	PIRQ and SMI disabled, no R/W bits set in USBLEGSUP;
+	 *	Controller is stopped and configured with EGSM set;
+	 *	No interrupts enabled except possibly Resume Detect.
+	 *
+	 * If any of these conditions are violated we do a complete reset.
+	 */
+	pci_read_config_word(pdev, UHCI_USBLEGSUP, &legsup);
+	if (legsup & ~(UHCI_USBLEGSUP_RO | UHCI_USBLEGSUP_RWC)) {
+		dev_dbg(&pdev->dev, "%s: legsup = 0x%04x\n",
+				__FUNCTION__, legsup);
+		goto reset_needed;
+	}
+
+	cmd = inw(base + UHCI_USBCMD);
+	if ((cmd & UHCI_USBCMD_RUN) || !(cmd & UHCI_USBCMD_CONFIGURE) ||
+			!(cmd & UHCI_USBCMD_EGSM)) {
+		dev_dbg(&pdev->dev, "%s: cmd = 0x%04x\n",
+				__FUNCTION__, cmd);
+		goto reset_needed;
+	}
+
+	intr = inw(base + UHCI_USBINTR);
+	if (intr & (~UHCI_USBINTR_RESUME)) {
+		dev_dbg(&pdev->dev, "%s: intr = 0x%04x\n",
+				__FUNCTION__, intr);
+		goto reset_needed;
+	}
+	return 0;
+
+reset_needed:
+	dev_dbg(&pdev->dev, "Performing full reset\n");
+	uhci_reset_hc(pdev, base);
+	return 1;
+}
+EXPORT_SYMBOL_GPL(uhci_check_and_reset_hc);
+
+static void __devinit quirk_usb_handoff_uhci(struct pci_dev *pdev)
+{
+	unsigned long base = 0;
+	int i;
+
+	for (i = 0; i < PCI_ROM_RESOURCE; i++)
+		if ((pci_resource_flags(pdev, i) & IORESOURCE_IO)) {
+			base = pci_resource_start(pdev, i);
+			break;
+		}
+
+	if (base)
+		uhci_check_and_reset_hc(pdev, base);
+}
+
+static void __devinit quirk_usb_handoff_ohci(struct pci_dev *pdev)
+{
+	void __iomem *base;
+	int wait_time;
+	u32 control;
+
+	base = ioremap_nocache(pci_resource_start(pdev, 0),
+				     pci_resource_len(pdev, 0));
+	if (base == NULL) return;
+
+/* On PA-RISC, PDC can leave IR set incorrectly; ignore it there. */
+#ifndef __hppa__
+	control = readl(base + OHCI_CONTROL);
+	if (control & OHCI_CTRL_IR) {
+		wait_time = 500; /* arbitrary; 5 seconds */
+		writel(OHCI_INTR_OC, base + OHCI_INTRENABLE);
+		writel(OHCI_OCR, base + OHCI_CMDSTATUS);
+		while (wait_time > 0 &&
+				readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
+			wait_time -= 10;
+			msleep(10);
+		}
+		if (wait_time <= 0)
+			printk(KERN_WARNING "%s %s: early BIOS handoff "
+					"failed (BIOS bug ?)\n",
+					pdev->dev.bus_id, "OHCI");
+
+		/* reset controller, preserving RWC */
+		writel(control & OHCI_CTRL_RWC, base + OHCI_CONTROL);
+	}
+#endif
+
+	/*
+	 * disable interrupts
+	 */
+	writel(~(u32)0, base + OHCI_INTRDISABLE);
+	writel(~(u32)0, base + OHCI_INTRSTATUS);
+
+	iounmap(base);
+}
+
+static void __devinit quirk_usb_disable_ehci(struct pci_dev *pdev)
+{
+	int wait_time, delta;
+	void __iomem *base, *op_reg_base;
+	u32 hcc_params, val, temp;
+	u8 cap_length;
+
+	base = ioremap_nocache(pci_resource_start(pdev, 0),
+				pci_resource_len(pdev, 0));
+	if (base == NULL) return;
+
+	cap_length = readb(base);
+	op_reg_base = base + cap_length;
+	hcc_params = readl(base + EHCI_HCC_PARAMS);
+	hcc_params = (hcc_params >> 8) & 0xff;
+	if (hcc_params) {
+		pci_read_config_dword(pdev,
+					hcc_params + EHCI_USBLEGSUP,
+					&val);
+		if (((val & 0xff) == 1) && (val & EHCI_USBLEGSUP_BIOS)) {
+			/*
+			 * Ok, BIOS is in smm mode, try to hand off...
+			 */
+			pci_read_config_dword(pdev,
+						hcc_params + EHCI_USBLEGCTLSTS,
+						&temp);
+			pci_write_config_dword(pdev,
+						hcc_params + EHCI_USBLEGCTLSTS,
+						temp | EHCI_USBLEGCTLSTS_SOOE);
+			val |= EHCI_USBLEGSUP_OS;
+			pci_write_config_dword(pdev,
+						hcc_params + EHCI_USBLEGSUP,
+						val);
+
+			wait_time = 500;
+			do {
+				msleep(10);
+				wait_time -= 10;
+				pci_read_config_dword(pdev,
+						hcc_params + EHCI_USBLEGSUP,
+						&val);
+			} while (wait_time && (val & EHCI_USBLEGSUP_BIOS));
+			if (!wait_time) {
+				/*
+				 * well, possibly buggy BIOS...
+				 */
+				printk(KERN_WARNING "%s %s: early BIOS handoff "
+						"failed (BIOS bug ?)\n",
+					pdev->dev.bus_id, "EHCI");
+				pci_write_config_dword(pdev,
+						hcc_params + EHCI_USBLEGSUP,
+						EHCI_USBLEGSUP_OS);
+				pci_write_config_dword(pdev,
+						hcc_params + EHCI_USBLEGCTLSTS,
+						0);
+			}
+		}
+	}
+
+	/*
+	 * halt EHCI & disable its interrupts in any case
+	 */
+	val = readl(op_reg_base + EHCI_USBSTS);
+	if ((val & EHCI_USBSTS_HALTED) == 0) {
+		val = readl(op_reg_base + EHCI_USBCMD);
+		val &= ~EHCI_USBCMD_RUN;
+		writel(val, op_reg_base + EHCI_USBCMD);
+
+		wait_time = 2000;
+		delta = 100;
+		do {
+			writel(0x3f, op_reg_base + EHCI_USBSTS);
+			udelay(delta);
+			wait_time -= delta;
+			val = readl(op_reg_base + EHCI_USBSTS);
+			if ((val == ~(u32)0) || (val & EHCI_USBSTS_HALTED)) {
+				break;
+			}
+		} while (wait_time > 0);
+	}
+	writel(0, op_reg_base + EHCI_USBINTR);
+	writel(0x3f, op_reg_base + EHCI_USBSTS);
+
+	iounmap(base);
+
+	return;
+}
+
+
+
+static void __devinit quirk_usb_early_handoff(struct pci_dev *pdev)
+{
+	if (pdev->class == PCI_CLASS_SERIAL_USB_UHCI)
+		quirk_usb_handoff_uhci(pdev);
+	else if (pdev->class == PCI_CLASS_SERIAL_USB_OHCI)
+		quirk_usb_handoff_ohci(pdev);
+	else if (pdev->class == PCI_CLASS_SERIAL_USB_EHCI)
+		quirk_usb_disable_ehci(pdev);
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_usb_early_handoff);
diff --git a/drivers/usb/host/sl811-hcd.c b/drivers/usb/host/sl811-hcd.c
index b5e7a478bc01..40169d9cf2b1 100644
--- a/drivers/usb/host/sl811-hcd.c
+++ b/drivers/usb/host/sl811-hcd.c
@@ -1363,7 +1363,7 @@ error:
 #ifdef	CONFIG_PM
 
 static int
-sl811h_hub_suspend(struct usb_hcd *hcd)
+sl811h_bus_suspend(struct usb_hcd *hcd)
 {
 	// SOFs off
 	DBG("%s\n", __FUNCTION__);
@@ -1371,7 +1371,7 @@ sl811h_hub_suspend(struct usb_hcd *hcd)
 }
 
 static int
-sl811h_hub_resume(struct usb_hcd *hcd)
+sl811h_bus_resume(struct usb_hcd *hcd)
 {
 	// SOFs on
 	DBG("%s\n", __FUNCTION__);
@@ -1380,8 +1380,8 @@ sl811h_hub_resume(struct usb_hcd *hcd)
 
 #else
 
-#define	sl811h_hub_suspend	NULL
-#define	sl811h_hub_resume	NULL
+#define	sl811h_bus_suspend	NULL
+#define	sl811h_bus_resume	NULL
 
 #endif
 
@@ -1623,8 +1623,8 @@ static struct hc_driver sl811h_hc_driver = {
 	 */
 	.hub_status_data =	sl811h_hub_status_data,
 	.hub_control =		sl811h_hub_control,
-	.hub_suspend =		sl811h_hub_suspend,
-	.hub_resume =		sl811h_hub_resume,
+	.bus_suspend =		sl811h_bus_suspend,
+	.bus_resume =		sl811h_bus_resume,
 };
 
 /*-------------------------------------------------------------------------*/
@@ -1791,7 +1791,7 @@ sl811h_suspend(struct device *dev, pm_message_t state)
 	int		retval = 0;
 
 	if (state.event == PM_EVENT_FREEZE)
-		retval = sl811h_hub_suspend(hcd);
+		retval = sl811h_bus_suspend(hcd);
 	else if (state.event == PM_EVENT_SUSPEND)
 		port_power(sl811, 0);
 	if (retval == 0)
@@ -1816,7 +1816,7 @@ sl811h_resume(struct device *dev)
 	}
 
 	dev->power.power_state = PMSG_ON;
-	return sl811h_hub_resume(hcd);
+	return sl811h_bus_resume(hcd);
 }
 
 #else
@@ -1831,6 +1831,7 @@ sl811h_resume(struct device *dev)
 struct device_driver sl811h_driver = {
 	.name =		(char *) hcd_name,
 	.bus =		&platform_bus_type,
+	.owner =	THIS_MODULE,
 
 	.probe =	sl811h_probe,
 	.remove =	__devexit_p(sl811h_remove),
diff --git a/drivers/usb/host/uhci-debug.c b/drivers/usb/host/uhci-debug.c
index 4538a98b6f9d..151154df37fa 100644
--- a/drivers/usb/host/uhci-debug.c
+++ b/drivers/usb/host/uhci-debug.c
@@ -348,7 +348,6 @@ static int uhci_show_urbp(struct uhci_hcd *uhci, struct urb_priv *urbp, char *bu
 
 	if (urbp->urb->status != -EINPROGRESS)
 		out += sprintf(out, "Status=%d ", urbp->urb->status);
-	//out += sprintf(out, "Inserttime=%lx ",urbp->inserttime);
 	//out += sprintf(out, "FSBRtime=%lx ",urbp->fsbrtime);
 
 	count = 0;
@@ -446,11 +445,11 @@ static int uhci_sprint_schedule(struct uhci_hcd *uhci, char *buf, int len)
 	out += sprintf(out, "Frame List\n");
 	for (i = 0; i < UHCI_NUMFRAMES; ++i) {
 		int shown = 0;
-		td = uhci->fl->frame_cpu[i];
+		td = uhci->frame_cpu[i];
 		if (!td)
 			continue;
 
-		if (td->dma_handle != (dma_addr_t)uhci->fl->frame[i]) {
+		if (td->dma_handle != (dma_addr_t)uhci->frame[i]) {
 			show_frame_num();
 			out += sprintf(out, "    frame list does not match td->dma_handle!\n");
 		}
diff --git a/drivers/usb/host/uhci-hcd.c b/drivers/usb/host/uhci-hcd.c
index 0c024898cbea..15e0a511069b 100644
--- a/drivers/usb/host/uhci-hcd.c
+++ b/drivers/usb/host/uhci-hcd.c
@@ -101,37 +101,16 @@ static void uhci_get_current_frame_number(struct uhci_hcd *uhci);
 #include "uhci-q.c"
 #include "uhci-hub.c"
 
+extern void uhci_reset_hc(struct pci_dev *pdev, unsigned long base);
+extern int uhci_check_and_reset_hc(struct pci_dev *pdev, unsigned long base);
+
 /*
- * Make sure the controller is completely inactive, unable to
- * generate interrupts or do DMA.
+ * Finish up a host controller reset and update the recorded state.
  */
-static void reset_hc(struct uhci_hcd *uhci)
+static void finish_reset(struct uhci_hcd *uhci)
 {
 	int port;
 
-	/* Turn off PIRQ enable and SMI enable.  (This also turns off the
-	 * BIOS's USB Legacy Support.)  Turn off all the R/WC bits too.
-	 */
-	pci_write_config_word(to_pci_dev(uhci_dev(uhci)), USBLEGSUP,
-			USBLEGSUP_RWC);
-
-	/* Reset the HC - this will force us to get a
-	 * new notification of any already connected
-	 * ports due to the virtual disconnect that it
-	 * implies.
-	 */
-	outw(USBCMD_HCRESET, uhci->io_addr + USBCMD);
-	mb();
-	udelay(5);
-	if (inw(uhci->io_addr + USBCMD) & USBCMD_HCRESET)
-		dev_warn(uhci_dev(uhci), "HCRESET not completed yet!\n");
-
-	/* Just to be safe, disable interrupt requests and
-	 * make sure the controller is stopped.
-	 */
-	outw(0, uhci->io_addr + USBINTR);
-	outw(0, uhci->io_addr + USBCMD);
-
 	/* HCRESET doesn't affect the Suspend, Reset, and Resume Detect
 	 * bits in the port status and control registers.
 	 * We have to clear them by hand.
@@ -153,7 +132,8 @@ static void reset_hc(struct uhci_hcd *uhci)
  */
 static void hc_died(struct uhci_hcd *uhci)
 {
-	reset_hc(uhci);
+	uhci_reset_hc(to_pci_dev(uhci_dev(uhci)), uhci->io_addr);
+	finish_reset(uhci);
 	uhci->hc_inaccessible = 1;
 }
 
@@ -163,44 +143,8 @@ static void hc_died(struct uhci_hcd *uhci)
  */
 static void check_and_reset_hc(struct uhci_hcd *uhci)
 {
-	u16 legsup;
-	unsigned int cmd, intr;
-
-	/*
-	 * When restarting a suspended controller, we expect all the
-	 * settings to be the same as we left them:
-	 *
-	 *	PIRQ and SMI disabled, no R/W bits set in USBLEGSUP;
-	 *	Controller is stopped and configured with EGSM set;
-	 *	No interrupts enabled except possibly Resume Detect.
-	 *
-	 * If any of these conditions are violated we do a complete reset.
-	 */
-	pci_read_config_word(to_pci_dev(uhci_dev(uhci)), USBLEGSUP, &legsup);
-	if (legsup & ~(USBLEGSUP_RO | USBLEGSUP_RWC)) {
-		dev_dbg(uhci_dev(uhci), "%s: legsup = 0x%04x\n",
-				__FUNCTION__, legsup);
-		goto reset_needed;
-	}
-
-	cmd = inw(uhci->io_addr + USBCMD);
-	if ((cmd & USBCMD_RS) || !(cmd & USBCMD_CF) || !(cmd & USBCMD_EGSM)) {
-		dev_dbg(uhci_dev(uhci), "%s: cmd = 0x%04x\n",
-				__FUNCTION__, cmd);
-		goto reset_needed;
-	}
-
-	intr = inw(uhci->io_addr + USBINTR);
-	if (intr & (~USBINTR_RESUME)) {
-		dev_dbg(uhci_dev(uhci), "%s: intr = 0x%04x\n",
-				__FUNCTION__, intr);
-		goto reset_needed;
-	}
-	return;
-
-reset_needed:
-	dev_dbg(uhci_dev(uhci), "Performing full reset\n");
-	reset_hc(uhci);
+	if (uhci_check_and_reset_hc(to_pci_dev(uhci_dev(uhci)), uhci->io_addr))
+		finish_reset(uhci);
 }
 
 /*
@@ -212,13 +156,13 @@ static void configure_hc(struct uhci_hcd *uhci)
 	outb(USBSOF_DEFAULT, uhci->io_addr + USBSOF);
 
 	/* Store the frame list base address */
-	outl(uhci->fl->dma_handle, uhci->io_addr + USBFLBASEADD);
+	outl(uhci->frame_dma_handle, uhci->io_addr + USBFLBASEADD);
 
 	/* Set the current frame number */
 	outw(uhci->frame_number, uhci->io_addr + USBFRNUM);
 
-	/* Mark controller as running before we enable interrupts */
-	uhci_to_hcd(uhci)->state = HC_STATE_RUNNING;
+	/* Mark controller as not halted before we enable interrupts */
+	uhci_to_hcd(uhci)->state = HC_STATE_SUSPENDED;
 	mb();
 
 	/* Enable PIRQ */
@@ -319,6 +263,7 @@ __acquires(uhci->lock)
 
 static void start_rh(struct uhci_hcd *uhci)
 {
+	uhci_to_hcd(uhci)->state = HC_STATE_RUNNING;
 	uhci->is_stopped = 0;
 	smp_wmb();
 
@@ -437,36 +382,21 @@ static void release_uhci(struct uhci_hcd *uhci)
 	int i;
 
 	for (i = 0; i < UHCI_NUM_SKELQH; i++)
-		if (uhci->skelqh[i]) {
-			uhci_free_qh(uhci, uhci->skelqh[i]);
-			uhci->skelqh[i] = NULL;
-		}
+		uhci_free_qh(uhci, uhci->skelqh[i]);
 
-	if (uhci->term_td) {
-		uhci_free_td(uhci, uhci->term_td);
-		uhci->term_td = NULL;
-	}
+	uhci_free_td(uhci, uhci->term_td);
 
-	if (uhci->qh_pool) {
-		dma_pool_destroy(uhci->qh_pool);
-		uhci->qh_pool = NULL;
-	}
+	dma_pool_destroy(uhci->qh_pool);
 
-	if (uhci->td_pool) {
-		dma_pool_destroy(uhci->td_pool);
-		uhci->td_pool = NULL;
-	}
+	dma_pool_destroy(uhci->td_pool);
 
-	if (uhci->fl) {
-		dma_free_coherent(uhci_dev(uhci), sizeof(*uhci->fl),
-				uhci->fl, uhci->fl->dma_handle);
-		uhci->fl = NULL;
-	}
+	kfree(uhci->frame_cpu);
 
-	if (uhci->dentry) {
-		debugfs_remove(uhci->dentry);
-		uhci->dentry = NULL;
-	}
+	dma_free_coherent(uhci_dev(uhci),
+			UHCI_NUMFRAMES * sizeof(*uhci->frame),
+			uhci->frame, uhci->frame_dma_handle);
+
+	debugfs_remove(uhci->dentry);
 }
 
 static int uhci_reset(struct usb_hcd *hcd)
@@ -545,7 +475,6 @@ static int uhci_start(struct usb_hcd *hcd)
 	struct uhci_hcd *uhci = hcd_to_uhci(hcd);
 	int retval = -EBUSY;
 	int i;
-	dma_addr_t dma_handle;
 	struct dentry *dentry;
 
 	hcd->uses_new_polling = 1;
@@ -579,17 +508,23 @@ static int uhci_start(struct usb_hcd *hcd)
 
 	init_waitqueue_head(&uhci->waitqh);
 
-	uhci->fl = dma_alloc_coherent(uhci_dev(uhci), sizeof(*uhci->fl),
-			&dma_handle, 0);
-	if (!uhci->fl) {
+	uhci->frame = dma_alloc_coherent(uhci_dev(uhci),
+			UHCI_NUMFRAMES * sizeof(*uhci->frame),
+			&uhci->frame_dma_handle, 0);
+	if (!uhci->frame) {
 		dev_err(uhci_dev(uhci), "unable to allocate "
 				"consistent memory for frame list\n");
-		goto err_alloc_fl;
+		goto err_alloc_frame;
 	}
+	memset(uhci->frame, 0, UHCI_NUMFRAMES * sizeof(*uhci->frame));
 
-	memset((void *)uhci->fl, 0, sizeof(*uhci->fl));
-
-	uhci->fl->dma_handle = dma_handle;
+	uhci->frame_cpu = kcalloc(UHCI_NUMFRAMES, sizeof(*uhci->frame_cpu),
+			GFP_KERNEL);
+	if (!uhci->frame_cpu) {
+		dev_err(uhci_dev(uhci), "unable to allocate "
+				"memory for frame pointers\n");
+		goto err_alloc_frame_cpu;
+	}
 
 	uhci->td_pool = dma_pool_create("uhci_td", uhci_dev(uhci),
 			sizeof(struct uhci_td), 16, 0);
@@ -672,7 +607,7 @@ static int uhci_start(struct usb_hcd *hcd)
 			irq = 7;
 
 		/* Only place we don't use the frame list routines */
-		uhci->fl->frame[i] = UHCI_PTR_QH |
+		uhci->frame[i] = UHCI_PTR_QH |
 				cpu_to_le32(uhci->skelqh[irq]->dma_handle);
 	}
 
@@ -690,31 +625,29 @@ static int uhci_start(struct usb_hcd *hcd)
  * error exits:
  */
 err_alloc_skelqh:
-	for (i = 0; i < UHCI_NUM_SKELQH; i++)
-		if (uhci->skelqh[i]) {
+	for (i = 0; i < UHCI_NUM_SKELQH; i++) {
+		if (uhci->skelqh[i])
 			uhci_free_qh(uhci, uhci->skelqh[i]);
-			uhci->skelqh[i] = NULL;
-		}
+	}
 
 	uhci_free_td(uhci, uhci->term_td);
-	uhci->term_td = NULL;
 
 err_alloc_term_td:
 	dma_pool_destroy(uhci->qh_pool);
-	uhci->qh_pool = NULL;
 
 err_create_qh_pool:
 	dma_pool_destroy(uhci->td_pool);
-	uhci->td_pool = NULL;
 
 err_create_td_pool:
-	dma_free_coherent(uhci_dev(uhci), sizeof(*uhci->fl),
-			uhci->fl, uhci->fl->dma_handle);
-	uhci->fl = NULL;
+	kfree(uhci->frame_cpu);
+
+err_alloc_frame_cpu:
+	dma_free_coherent(uhci_dev(uhci),
+			UHCI_NUMFRAMES * sizeof(*uhci->frame),
+			uhci->frame, uhci->frame_dma_handle);
 
-err_alloc_fl:
+err_alloc_frame:
 	debugfs_remove(uhci->dentry);
-	uhci->dentry = NULL;
 
 err_create_debug_entry:
 	return retval;
@@ -726,7 +659,7 @@ static void uhci_stop(struct usb_hcd *hcd)
 
 	spin_lock_irq(&uhci->lock);
 	if (!uhci->hc_inaccessible)
-		reset_hc(uhci);
+		hc_died(uhci);
 	uhci_scan_schedule(uhci, NULL);
 	spin_unlock_irq(&uhci->lock);
 
@@ -774,14 +707,8 @@ static int uhci_suspend(struct usb_hcd *hcd, pm_message_t message)
 	if (uhci->hc_inaccessible)	/* Dead or already suspended */
 		goto done;
 
-#ifndef CONFIG_USB_SUSPEND
-	/* Otherwise this would never happen */
-	suspend_rh(uhci, UHCI_RH_SUSPENDED);
-#endif
-
 	if (uhci->rh_state > UHCI_RH_SUSPENDED) {
 		dev_warn(uhci_dev(uhci), "Root hub isn't suspended!\n");
-		hcd->state = HC_STATE_RUNNING;
 		rc = -EBUSY;
 		goto done;
 	};
@@ -820,10 +747,6 @@ static int uhci_resume(struct usb_hcd *hcd)
 	check_and_reset_hc(uhci);
 	configure_hc(uhci);
 
-#ifndef CONFIG_USB_SUSPEND
-	/* Otherwise this would never happen */
-	wakeup_rh(uhci);
-#endif
 	if (uhci->rh_state == UHCI_RH_RESET)
 		suspend_rh(uhci, UHCI_RH_SUSPENDED);
 
@@ -881,8 +804,8 @@ static const struct hc_driver uhci_driver = {
 #ifdef CONFIG_PM
 	.suspend =		uhci_suspend,
 	.resume =		uhci_resume,
-	.hub_suspend =		uhci_rh_suspend,
-	.hub_resume =		uhci_rh_resume,
+	.bus_suspend =		uhci_rh_suspend,
+	.bus_resume =		uhci_rh_resume,
 #endif
 	.stop =			uhci_stop,
 
@@ -908,6 +831,7 @@ MODULE_DEVICE_TABLE(pci, uhci_pci_ids);
 static struct pci_driver uhci_pci_driver = {
 	.name =		(char *)hcd_name,
 	.id_table =	uhci_pci_ids,
+	.owner =	THIS_MODULE,
 
 	.probe =	usb_hcd_pci_probe,
 	.remove =	usb_hcd_pci_remove,
diff --git a/drivers/usb/host/uhci-hcd.h b/drivers/usb/host/uhci-hcd.h
index 282f40b75881..e576db57a926 100644
--- a/drivers/usb/host/uhci-hcd.h
+++ b/drivers/usb/host/uhci-hcd.h
@@ -7,6 +7,7 @@
 #define usb_packetid(pipe)	(usb_pipein(pipe) ? USB_PID_IN : USB_PID_OUT)
 #define PIPE_DEVEP_MASK		0x0007ff00
 
+
 /*
  * Universal Host Controller Interface data structures and defines
  */
@@ -82,15 +83,10 @@
 #define UHCI_MAX_SOF_NUMBER	2047	/* in an SOF packet */
 #define CAN_SCHEDULE_FRAMES	1000	/* how far future frames can be scheduled */
 
-struct uhci_frame_list {
-	__le32 frame[UHCI_NUMFRAMES];
-
-	void *frame_cpu[UHCI_NUMFRAMES];
-
-	dma_addr_t dma_handle;
-};
 
-struct urb_priv;
+/*
+ *	Queue Headers
+ */
 
 /*
  * One role of a QH is to hold a queue of TDs for some endpoint.  Each QH is
@@ -116,13 +112,13 @@ struct uhci_qh {
 
 	struct urb_priv *urbp;
 
-	struct list_head list;		/* P: uhci->frame_list_lock */
-	struct list_head remove_list;	/* P: uhci->remove_list_lock */
+	struct list_head list;
+	struct list_head remove_list;
 } __attribute__((aligned(16)));
 
 /*
  * We need a special accessor for the element pointer because it is
- * subject to asynchronous updates by the controller
+ * subject to asynchronous updates by the controller.
  */
 static __le32 inline qh_element(struct uhci_qh *qh) {
 	__le32 element = qh->element;
@@ -131,6 +127,11 @@ static __le32 inline qh_element(struct uhci_qh *qh) {
 	return element;
 }
 
+
+/*
+ *	Transfer Descriptors
+ */
+
 /*
  * for TD <status>:
  */
@@ -183,17 +184,10 @@ static __le32 inline qh_element(struct uhci_qh *qh) {
  *
  * That's silly, the hardware doesn't care. The hardware only cares that
  * the hardware words are 16-byte aligned, and we can have any amount of
- * sw space after the TD entry as far as I can tell.
- *
- * But let's just go with the documentation, at least for 32-bit machines.
- * On 64-bit machines we probably want to take advantage of the fact that
- * hw doesn't really care about the size of the sw-only area.
- *
- * Alas, not anymore, we have more than 4 words for software, woops.
- * Everything still works tho, surprise! -jerdfelt
+ * sw space after the TD entry.
  *
  * td->link points to either another TD (not necessarily for the same urb or
- * even the same endpoint), or nothing (PTR_TERM), or a QH (for queued urbs)
+ * even the same endpoint), or nothing (PTR_TERM), or a QH (for queued urbs).
  */
 struct uhci_td {
 	/* Hardware fields */
@@ -205,18 +199,16 @@ struct uhci_td {
 	/* Software fields */
 	dma_addr_t dma_handle;
 
-	struct urb *urb;
-
-	struct list_head list;		/* P: urb->lock */
-	struct list_head remove_list;	/* P: uhci->td_remove_list_lock */
+	struct list_head list;
+	struct list_head remove_list;
 
 	int frame;			/* for iso: what frame? */
-	struct list_head fl_list;	/* P: uhci->frame_list_lock */
+	struct list_head fl_list;
 } __attribute__((aligned(16)));
 
 /*
  * We need a special accessor for the control/status word because it is
- * subject to asynchronous updates by the controller
+ * subject to asynchronous updates by the controller.
  */
 static u32 inline td_status(struct uhci_td *td) {
 	__le32 status = td->status;
@@ -227,6 +219,10 @@ static u32 inline td_status(struct uhci_td *td) {
 
 
 /*
+ *	Skeleton Queue Headers
+ */
+
+/*
  * The UHCI driver places Interrupt, Control and Bulk into QH's both
  * to group together TD's for one transfer, and also to faciliate queuing
  * of URB's. To make it easy to insert entries into the schedule, we have
@@ -256,15 +252,15 @@ static u32 inline td_status(struct uhci_td *td) {
  *
  * The terminating QH is used for 2 reasons:
  * - To place a terminating TD which is used to workaround a PIIX bug
- *   (see Intel errata for explanation)
+ *   (see Intel errata for explanation), and
  * - To loop back to the full-speed control queue for full-speed bandwidth
- *   reclamation
+ *   reclamation.
  *
  * Isochronous transfers are stored before the start of the skeleton
  * schedule and don't use QH's. While the UHCI spec doesn't forbid the
- * use of QH's for Isochronous, it doesn't use them either. Since we don't
- * need to use them either, we follow the spec diagrams in hope that it'll
- * be more compatible with future UHCI implementations.
+ * use of QH's for Isochronous, it doesn't use them either. And the spec
+ * says that queues never advance on an error completion status, which
+ * makes them totally unsuitable for Isochronous transfers.
  */
 
 #define UHCI_NUM_SKELQH		12
@@ -314,8 +310,13 @@ static inline int __interval_to_skel(int interval)
 	return 0;				/* int128 for 128-255 ms (Max.) */
 }
 
+
+/*
+ *	The UHCI controller and root hub
+ */
+
 /*
- * States for the root hub.
+ * States for the root hub:
  *
  * To prevent "bouncing" in the presence of electrical noise,
  * when there are no devices attached we delay for 1 second in the
@@ -326,7 +327,7 @@ static inline int __interval_to_skel(int interval)
  */
 enum uhci_rh_state {
 	/* In the following states the HC must be halted.
-	 * These two must come first */
+	 * These two must come first. */
 	UHCI_RH_RESET,
 	UHCI_RH_SUSPENDED,
 
@@ -338,13 +339,13 @@ enum uhci_rh_state {
 	UHCI_RH_SUSPENDING,
 
 	/* In the following states it's an error if the HC is halted.
-	 * These two must come last */
+	 * These two must come last. */
 	UHCI_RH_RUNNING,		/* The normal state */
 	UHCI_RH_RUNNING_NODEVS,		/* Running with no devices attached */
 };
 
 /*
- * This describes the full uhci information.
+ * The full UHCI controller information:
  */
 struct uhci_hcd {
 
@@ -361,7 +362,11 @@ struct uhci_hcd {
 	struct uhci_qh *skelqh[UHCI_NUM_SKELQH];	/* Skeleton QH's */
 
 	spinlock_t lock;
-	struct uhci_frame_list *fl;		/* P: uhci->lock */
+
+	dma_addr_t frame_dma_handle;		/* Hardware frame list */
+	__le32 *frame;
+	void **frame_cpu;			/* CPU's frame list */
+
 	int fsbr;				/* Full-speed bandwidth reclamation */
 	unsigned long fsbrtimeout;		/* FSBR delay */
 
@@ -385,22 +390,22 @@ struct uhci_hcd {
 	unsigned long ports_timeout;		/* Time to stop signalling */
 
 	/* Main list of URB's currently controlled by this HC */
-	struct list_head urb_list;		/* P: uhci->lock */
+	struct list_head urb_list;
 
 	/* List of QH's that are done, but waiting to be unlinked (race) */
-	struct list_head qh_remove_list;	/* P: uhci->lock */
+	struct list_head qh_remove_list;
 	unsigned int qh_remove_age;		/* Age in frames */
 
 	/* List of TD's that are done, but waiting to be freed (race) */
-	struct list_head td_remove_list;	/* P: uhci->lock */
+	struct list_head td_remove_list;
 	unsigned int td_remove_age;		/* Age in frames */
 
 	/* List of asynchronously unlinked URB's */
-	struct list_head urb_remove_list;	/* P: uhci->lock */
+	struct list_head urb_remove_list;
 	unsigned int urb_remove_age;		/* Age in frames */
 
 	/* List of URB's awaiting completion callback */
-	struct list_head complete_list;		/* P: uhci->lock */
+	struct list_head complete_list;
 
 	int rh_numports;			/* Number of root-hub ports */
 
@@ -419,13 +424,17 @@ static inline struct usb_hcd *uhci_to_hcd(struct uhci_hcd *uhci)
 
 #define uhci_dev(u)	(uhci_to_hcd(u)->self.controller)
 
+
+/*
+ *	Private per-URB data
+ */
 struct urb_priv {
 	struct list_head urb_list;
 
 	struct urb *urb;
 
 	struct uhci_qh *qh;		/* QH for this URB */
-	struct list_head td_list;	/* P: urb->lock */
+	struct list_head td_list;
 
 	unsigned fsbr : 1;		/* URB turned on FSBR */
 	unsigned fsbr_timeout : 1;	/* URB timed out on FSBR */
@@ -434,12 +443,12 @@ struct urb_priv {
 						/*  a control transfer, retrigger */
 						/*  the status phase */
 
-	unsigned long inserttime;	/* In jiffies */
 	unsigned long fsbrtime;		/* In jiffies */
 
-	struct list_head queue_list;	/* P: uhci->frame_list_lock */
+	struct list_head queue_list;
 };
 
+
 /*
  * Locking in uhci.c
  *
@@ -459,6 +468,5 @@ struct urb_priv {
 
 #define PCI_VENDOR_ID_GENESYS		0x17a0
 #define PCI_DEVICE_ID_GL880S_UHCI	0x8083
-#define PCI_DEVICE_ID_GL880S_EHCI	0x8084
 
 #endif
diff --git a/drivers/usb/host/uhci-q.c b/drivers/usb/host/uhci-q.c
index 4e0fbe2c1a9a..7e46887d9e12 100644
--- a/drivers/usb/host/uhci-q.c
+++ b/drivers/usb/host/uhci-q.c
@@ -89,10 +89,10 @@ static void uhci_insert_td_frame_list(struct uhci_hcd *uhci, struct uhci_td *td,
 	td->frame = framenum;
 
 	/* Is there a TD already mapped there? */
-	if (uhci->fl->frame_cpu[framenum]) {
+	if (uhci->frame_cpu[framenum]) {
 		struct uhci_td *ftd, *ltd;
 
-		ftd = uhci->fl->frame_cpu[framenum];
+		ftd = uhci->frame_cpu[framenum];
 		ltd = list_entry(ftd->fl_list.prev, struct uhci_td, fl_list);
 
 		list_add_tail(&td->fl_list, &ftd->fl_list);
@@ -101,29 +101,32 @@ static void uhci_insert_td_frame_list(struct uhci_hcd *uhci, struct uhci_td *td,
 		wmb();
 		ltd->link = cpu_to_le32(td->dma_handle);
 	} else {
-		td->link = uhci->fl->frame[framenum];
+		td->link = uhci->frame[framenum];
 		wmb();
-		uhci->fl->frame[framenum] = cpu_to_le32(td->dma_handle);
-		uhci->fl->frame_cpu[framenum] = td;
+		uhci->frame[framenum] = cpu_to_le32(td->dma_handle);
+		uhci->frame_cpu[framenum] = td;
 	}
 }
 
-static void uhci_remove_td(struct uhci_hcd *uhci, struct uhci_td *td)
+static inline void uhci_remove_td_frame_list(struct uhci_hcd *uhci,
+		struct uhci_td *td)
 {
 	/* If it's not inserted, don't remove it */
-	if (td->frame == -1 && list_empty(&td->fl_list))
+	if (td->frame == -1) {
+		WARN_ON(!list_empty(&td->fl_list));
 		return;
+	}
 
-	if (td->frame != -1 && uhci->fl->frame_cpu[td->frame] == td) {
+	if (uhci->frame_cpu[td->frame] == td) {
 		if (list_empty(&td->fl_list)) {
-			uhci->fl->frame[td->frame] = td->link;
-			uhci->fl->frame_cpu[td->frame] = NULL;
+			uhci->frame[td->frame] = td->link;
+			uhci->frame_cpu[td->frame] = NULL;
 		} else {
 			struct uhci_td *ntd;
 
 			ntd = list_entry(td->fl_list.next, struct uhci_td, fl_list);
-			uhci->fl->frame[td->frame] = cpu_to_le32(ntd->dma_handle);
-			uhci->fl->frame_cpu[td->frame] = ntd;
+			uhci->frame[td->frame] = cpu_to_le32(ntd->dma_handle);
+			uhci->frame_cpu[td->frame] = ntd;
 		}
 	} else {
 		struct uhci_td *ptd;
@@ -132,13 +135,20 @@ static void uhci_remove_td(struct uhci_hcd *uhci, struct uhci_td *td)
 		ptd->link = td->link;
 	}
 
-	wmb();
-	td->link = UHCI_PTR_TERM;
-
 	list_del_init(&td->fl_list);
 	td->frame = -1;
 }
 
+static void unlink_isochronous_tds(struct uhci_hcd *uhci, struct urb *urb)
+{
+	struct urb_priv *urbp = (struct urb_priv *) urb->hcpriv;
+	struct uhci_td *td;
+
+	list_for_each_entry(td, &urbp->td_list, list)
+		uhci_remove_td_frame_list(uhci, td);
+	wmb();
+}
+
 /*
  * Inserts a td list into qh.
  */
@@ -443,7 +453,6 @@ static struct urb_priv *uhci_alloc_urb_priv(struct uhci_hcd *uhci, struct urb *u
 
 	memset((void *)urbp, 0, sizeof(*urbp));
 
-	urbp->inserttime = jiffies;
 	urbp->fsbrtime = jiffies;
 	urbp->urb = urb;
 	
@@ -462,8 +471,6 @@ static void uhci_add_td_to_urb(struct urb *urb, struct uhci_td *td)
 {
 	struct urb_priv *urbp = (struct urb_priv *)urb->hcpriv;
 
-	td->urb = urb;
-
 	list_add_tail(&td->list, &urbp->td_list);
 }
 
@@ -473,8 +480,6 @@ static void uhci_remove_td_from_urb(struct uhci_td *td)
 		return;
 
 	list_del_init(&td->list);
-
-	td->urb = NULL;
 }
 
 static void uhci_destroy_urb_priv(struct uhci_hcd *uhci, struct urb *urb)
@@ -503,7 +508,6 @@ static void uhci_destroy_urb_priv(struct uhci_hcd *uhci, struct urb *urb)
 
 	list_for_each_entry_safe(td, tmp, &urbp->td_list, list) {
 		uhci_remove_td_from_urb(td);
-		uhci_remove_td(uhci, td);
 		list_add(&td->remove_list, &uhci->td_remove_list);
 	}
 
@@ -1073,6 +1077,7 @@ static int uhci_submit_isochronous(struct uhci_hcd *uhci, struct urb *urb)
 	struct uhci_td *td;
 	int i, ret, frame;
 	int status, destination;
+	struct urb_priv *urbp = (struct urb_priv *) urb->hcpriv;
 
 	status = TD_CTRL_ACTIVE | TD_CTRL_IOS;
 	destination = (urb->pipe & PIPE_DEVEP_MASK) | usb_packetid(urb->pipe);
@@ -1081,11 +1086,7 @@ static int uhci_submit_isochronous(struct uhci_hcd *uhci, struct urb *urb)
 	if (ret)
 		return ret;
 
-	frame = urb->start_frame;
-	for (i = 0; i < urb->number_of_packets; i++, frame += urb->interval) {
-		if (!urb->iso_frame_desc[i].length)
-			continue;
-
+	for (i = 0; i < urb->number_of_packets; i++) {
 		td = uhci_alloc_td(uhci);
 		if (!td)
 			return -ENOMEM;
@@ -1096,8 +1097,12 @@ static int uhci_submit_isochronous(struct uhci_hcd *uhci, struct urb *urb)
 
 		if (i + 1 >= urb->number_of_packets)
 			td->status |= cpu_to_le32(TD_CTRL_IOC);
+	}
 
+	frame = urb->start_frame;
+	list_for_each_entry(td, &urbp->td_list, list) {
 		uhci_insert_td_frame_list(uhci, td, frame);
+		frame += urb->interval;
 	}
 
 	return -EINPROGRESS;
@@ -1110,7 +1115,7 @@ static int uhci_result_isochronous(struct uhci_hcd *uhci, struct urb *urb)
 	int status;
 	int i, ret = 0;
 
-	urb->actual_length = 0;
+	urb->actual_length = urb->error_count = 0;
 
 	i = 0;
 	list_for_each_entry(td, &urbp->td_list, list) {
@@ -1134,6 +1139,7 @@ static int uhci_result_isochronous(struct uhci_hcd *uhci, struct urb *urb)
 
 		i++;
 	}
+	unlink_isochronous_tds(uhci, urb);
 
 	return ret;
 }
@@ -1366,6 +1372,8 @@ static int uhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb)
 		goto done;
 	list_del_init(&urbp->urb_list);
 
+	if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS)
+		unlink_isochronous_tds(uhci, urb);
 	uhci_unlink_generic(uhci, urb);
 
 	uhci_get_current_frame_number(uhci);