EHCI: centralize controller initialization

This patch (as1564c) converts the EHCI platform drivers to use the
central ehci_setup() routine for generic controller initialization
rather than each having its own idiosyncratic approach.

The major point of difficulty lies in ehci-pci's many vendor- and
device-specific workarounds.  Some of them have to be applied before
calling ehci_setup() and some after, which necessitates a fair amount
of code motion.  The other platform drivers require much smaller
changes.

One point not addressed by the patch is whether ports should be
powered on or off following initialization.  The different drivers
appear to handle this pretty much at random.  In fact it shouldn't
matter, because the hub driver turns on power to all ports when it
binds to the root hub.  Straightening that out will be left for
another day.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1 files changed, 79 insertions, 81 deletions

diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c
index 6e767bce0605..21e5f963f331 100644
--- a/drivers/usb/host/ehci-pci.c
+++ b/drivers/usb/host/ehci-pci.c
@@ -54,6 +54,17 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 	u32			temp;
 	int			retval;
 
+	ehci->caps = hcd->regs;
+
+	/*
+	 * ehci_init() causes memory for DMA transfers to be
+	 * allocated.  Thus, any vendor-specific workarounds based on
+	 * limiting the type of memory used for DMA transfers must
+	 * happen before ehci_setup() is called.
+	 *
+	 * Most other workarounds can be done either before or after
+	 * init and reset; they are located here too.
+	 */
 	switch (pdev->vendor) {
 	case PCI_VENDOR_ID_TOSHIBA_2:
 		/* celleb's companion chip */
@@ -66,20 +77,6 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 #endif
 		}
 		break;
-	}
-
-	ehci->caps = hcd->regs;
-	ehci->regs = hcd->regs +
-		HC_LENGTH(ehci, ehci_readl(ehci, &ehci->caps->hc_capbase));
-
-	dbg_hcs_params(ehci, "reset");
-	dbg_hcc_params(ehci, "reset");
-
-        /* ehci_init() causes memory for DMA transfers to be
-         * allocated.  Thus, any vendor-specific workarounds based on
-         * limiting the type of memory used for DMA transfers must
-         * happen before ehci_init() is called. */
-	switch (pdev->vendor) {
 	case PCI_VENDOR_ID_NVIDIA:
 		/* NVidia reports that certain chips don't handle
 		 * QH, ITD, or SITD addresses above 2GB.  (But TD,
@@ -95,61 +92,28 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 				ehci_warn(ehci, "can't enable NVidia "
 					"workaround for >2GB RAM\n");
 			break;
-		}
-		break;
-	}
 
-	/* cache this readonly data; minimize chip reads */
-	ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
-
-	retval = ehci_halt(ehci);
-	if (retval)
-		return retval;
-
-	if ((pdev->vendor == PCI_VENDOR_ID_AMD && pdev->device == 0x7808) ||
-	    (pdev->vendor == PCI_VENDOR_ID_ATI && pdev->device == 0x4396)) {
-		/* EHCI controller on AMD SB700/SB800/Hudson-2/3 platforms may
-		 * read/write memory space which does not belong to it when
-		 * there is NULL pointer with T-bit set to 1 in the frame list
-		 * table. To avoid the issue, the frame list link pointer
-		 * should always contain a valid pointer to a inactive qh.
+		/* Some NForce2 chips have problems with selective suspend;
+		 * fixed in newer silicon.
 		 */
-		ehci->use_dummy_qh = 1;
-		ehci_info(ehci, "applying AMD SB700/SB800/Hudson-2/3 EHCI "
-				"dummy qh workaround\n");
-	}
-
-	/* data structure init */
-	retval = ehci_init(hcd);
-	if (retval)
-		return retval;
-
-	switch (pdev->vendor) {
-	case PCI_VENDOR_ID_NEC:
-		ehci->need_io_watchdog = 0;
+		case 0x0068:
+			if (pdev->revision < 0xa4)
+				ehci->no_selective_suspend = 1;
+			break;
+		}
 		break;
 	case PCI_VENDOR_ID_INTEL:
-		ehci->need_io_watchdog = 0;
 		ehci->fs_i_thresh = 1;
 		if (pdev->device == 0x27cc) {
 			ehci->broken_periodic = 1;
 			ehci_info(ehci, "using broken periodic workaround\n");
 		}
-		if (pdev->device == 0x0806 || pdev->device == 0x0811
-				|| pdev->device == 0x0829) {
-			ehci_info(ehci, "disable lpm for langwell/penwell\n");
-			ehci->has_lpm = 0;
-		}
-		if (pdev->device == PCI_DEVICE_ID_INTEL_CE4100_USB) {
+		if (pdev->device == PCI_DEVICE_ID_INTEL_CE4100_USB)
 			hcd->has_tt = 1;
-			tdi_reset(ehci);
-		}
 		break;
 	case PCI_VENDOR_ID_TDI:
-		if (pdev->device == PCI_DEVICE_ID_TDI_EHCI) {
+		if (pdev->device == PCI_DEVICE_ID_TDI_EHCI)
 			hcd->has_tt = 1;
-			tdi_reset(ehci);
-		}
 		break;
 	case PCI_VENDOR_ID_AMD:
 		/* AMD PLL quirk */
@@ -161,28 +125,17 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 			retval = -EIO;
 			goto done;
 		}
-		break;
-	case PCI_VENDOR_ID_NVIDIA:
-		switch (pdev->device) {
-		/* Some NForce2 chips have problems with selective suspend;
-		 * fixed in newer silicon.
-		 */
-		case 0x0068:
-			if (pdev->revision < 0xa4)
-				ehci->no_selective_suspend = 1;
-			break;
 
-		/* MCP89 chips on the MacBookAir3,1 give EPROTO when
-		 * fetching device descriptors unless LPM is disabled.
-		 * There are also intermittent problems enumerating
-		 * devices with PPCD enabled.
+		/*
+		 * EHCI controller on AMD SB700/SB800/Hudson-2/3 platforms may
+		 * read/write memory space which does not belong to it when
+		 * there is NULL pointer with T-bit set to 1 in the frame list
+		 * table. To avoid the issue, the frame list link pointer
+		 * should always contain a valid pointer to a inactive qh.
 		 */
-		case 0x0d9d:
-			ehci_info(ehci, "disable lpm/ppcd for nvidia mcp89");
-			ehci->has_lpm = 0;
-			ehci->has_ppcd = 0;
-			ehci->command &= ~CMD_PPCEE;
-			break;
+		if (pdev->device == 0x7808) {
+			ehci->use_dummy_qh = 1;
+			ehci_info(ehci, "applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround\n");
 		}
 		break;
 	case PCI_VENDOR_ID_VIA:
@@ -203,6 +156,18 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 		/* AMD PLL quirk */
 		if (usb_amd_find_chipset_info())
 			ehci->amd_pll_fix = 1;
+
+		/*
+		 * EHCI controller on AMD SB700/SB800/Hudson-2/3 platforms may
+		 * read/write memory space which does not belong to it when
+		 * there is NULL pointer with T-bit set to 1 in the frame list
+		 * table. To avoid the issue, the frame list link pointer
+		 * should always contain a valid pointer to a inactive qh.
+		 */
+		if (pdev->device == 0x4396) {
+			ehci->use_dummy_qh = 1;
+			ehci_info(ehci, "applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround\n");
+		}
 		/* SB600 and old version of SB700 have a bug in EHCI controller,
 		 * which causes usb devices lose response in some cases.
 		 */
@@ -231,6 +196,40 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 		break;
 	}
 
+	retval = ehci_setup(hcd);
+	if (retval)
+		return retval;
+
+	/* These workarounds need to be applied after ehci_setup() */
+	switch (pdev->vendor) {
+	case PCI_VENDOR_ID_NEC:
+		ehci->need_io_watchdog = 0;
+		break;
+	case PCI_VENDOR_ID_INTEL:
+		ehci->need_io_watchdog = 0;
+		if (pdev->device == 0x0806 || pdev->device == 0x0811
+				|| pdev->device == 0x0829) {
+			ehci_info(ehci, "disable lpm for langwell/penwell\n");
+			ehci->has_lpm = 0;
+		}
+		break;
+	case PCI_VENDOR_ID_NVIDIA:
+		switch (pdev->device) {
+		/* MCP89 chips on the MacBookAir3,1 give EPROTO when
+		 * fetching device descriptors unless LPM is disabled.
+		 * There are also intermittent problems enumerating
+		 * devices with PPCD enabled.
+		 */
+		case 0x0d9d:
+			ehci_info(ehci, "disable lpm/ppcd for nvidia mcp89");
+			ehci->has_lpm = 0;
+			ehci->has_ppcd = 0;
+			ehci->command &= ~CMD_PPCEE;
+			break;
+		}
+		break;
+	}
+
 	/* optional debug port, normally in the first BAR */
 	temp = pci_find_capability(pdev, 0x0a);
 	if (temp) {
@@ -238,7 +237,7 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 		temp >>= 16;
 		if ((temp & (3 << 13)) == (1 << 13)) {
 			temp &= 0x1fff;
-			ehci->debug = ehci_to_hcd(ehci)->regs + temp;
+			ehci->debug = hcd->regs + temp;
 			temp = ehci_readl(ehci, &ehci->debug->control);
 			ehci_info(ehci, "debug port %d%s\n",
 				HCS_DEBUG_PORT(ehci->hcs_params),
@@ -250,8 +249,6 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 		}
 	}
 
-	ehci_reset(ehci);
-
 	/* at least the Genesys GL880S needs fixup here */
 	temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params);
 	temp &= 0x0f;
@@ -275,10 +272,11 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 	}
 
 	/* Serial Bus Release Number is at PCI 0x60 offset */
-	pci_read_config_byte(pdev, 0x60, &ehci->sbrn);
 	if (pdev->vendor == PCI_VENDOR_ID_STMICRO
 	    && pdev->device == PCI_DEVICE_ID_STMICRO_USB_HOST)
-		ehci->sbrn = 0x20; /* ConneXT has no sbrn register */
+		;	/* ConneXT has no sbrn register */
+	else
+		pci_read_config_byte(pdev, 0x60, &ehci->sbrn);
 
 	/* Keep this around for a while just in case some EHCI
 	 * implementation uses legacy PCI PM support.  This test