[SCSI] lpfc 8.3.17: SLI Additions and Fixes

- Added driver support for management application to pass down two security
  specific mailbox commands (MBX_SECURITY_MGMT and MBX_AUTH_PORT)
- Added driver support for handling FIPS zeroization trap of host ERATT ER8,
  performing selective reset and bringing the device up.
- Added code to detect INIT_LINK mailbox command completion returning status
  MBXERR_SEC_NO_PERMISSION.
- Increased the wait timeout on host status register HS_FFRDY and HS_MBRDY
  being set.
- Remove the port offline code from the Heartbeat TMO handler.

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

1 files changed, 39 insertions, 16 deletions

diff --git a/drivers/scsi/lpfc/lpfc_sli.c b/drivers/scsi/lpfc/lpfc_sli.c
index bbbd8ba5c1a7..34dd87f542c2 100644
--- a/drivers/scsi/lpfc/lpfc_sli.c
+++ b/drivers/scsi/lpfc/lpfc_sli.c
@@ -1677,6 +1677,8 @@ lpfc_sli_chk_mbx_command(uint8_t mbxCommand)
 	case MBX_RESUME_RPI:
 	case MBX_READ_EVENT_LOG_STATUS:
 	case MBX_READ_EVENT_LOG:
+	case MBX_SECURITY_MGMT:
+	case MBX_AUTH_PORT:
 		ret = mbxCommand;
 		break;
 	default:
@@ -1781,6 +1783,13 @@ lpfc_sli_def_mbox_cmpl(struct lpfc_hba *phba, LPFC_MBOXQ_t *pmb)
 		pmb->context2 = NULL;
 	}
 
+	/* Check security permission status on INIT_LINK mailbox command */
+	if ((pmb->u.mb.mbxCommand == MBX_INIT_LINK) &&
+	    (pmb->u.mb.mbxStatus == MBXERR_SEC_NO_PERMISSION))
+		lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+				"2860 SLI authentication is required "
+				"for INIT_LINK but has not done yet\n");
+
 	if (bf_get(lpfc_mqe_command, &pmb->u.mqe) == MBX_SLI4_CONFIG)
 		lpfc_sli4_mbox_cmd_free(phba, pmb);
 	else
@@ -3658,11 +3667,15 @@ lpfc_sli_chipset_init(struct lpfc_hba *phba)
 	i = 0;
 	while ((status & (HS_FFRDY | HS_MBRDY)) != (HS_FFRDY | HS_MBRDY)) {
 
-		/* Check every 100ms for 5 retries, then every 500ms for 5, then
-		 * every 2.5 sec for 5, then reset board and every 2.5 sec for
-		 * 4.
+		/* Check every 10ms for 10 retries, then every 100ms for 90
+		 * retries, then every 1 sec for 50 retires for a total of
+		 * ~60 seconds before reset the board again and check every
+		 * 1 sec for 50 retries. The up to 60 seconds before the
+		 * board ready is required by the Falcon FIPS zeroization
+		 * complete, and any reset the board in between shall cause
+		 * restart of zeroization, further delay the board ready.
 		 */
-		if (i++ >= 20) {
+		if (i++ >= 200) {
 			/* Adapter failed to init, timeout, status reg
 			   <status> */
 			lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
@@ -3690,16 +3703,15 @@ lpfc_sli_chipset_init(struct lpfc_hba *phba)
 			return -EIO;
 		}
 
-		if (i <= 5) {
+		if (i <= 10)
 			msleep(10);
-		} else if (i <= 10) {
-			msleep(500);
-		} else {
-			msleep(2500);
-		}
+		else if (i <= 100)
+			msleep(100);
+		else
+			msleep(1000);
 
-		if (i == 15) {
-				/* Do post */
+		if (i == 150) {
+			/* Do post */
 			phba->pport->port_state = LPFC_VPORT_UNKNOWN;
 			lpfc_sli_brdrestart(phba);
 		}
@@ -5950,6 +5962,8 @@ lpfc_sli4_iocb2wqe(struct lpfc_hba *phba, struct lpfc_iocbq *iocbq,
 	uint8_t command_type = ELS_COMMAND_NON_FIP;
 	uint8_t cmnd;
 	uint16_t xritag;
+	uint16_t abrt_iotag;
+	struct lpfc_iocbq *abrtiocbq;
 	struct ulp_bde64 *bpl = NULL;
 	uint32_t els_id = ELS_ID_DEFAULT;
 	int numBdes, i;
@@ -6162,9 +6176,17 @@ lpfc_sli4_iocb2wqe(struct lpfc_hba *phba, struct lpfc_iocbq *iocbq,
 	case CMD_ABORT_XRI_CX:
 		/* words 0-2 memcpy should be 0 rserved */
 		/* port will send abts */
-		if (iocbq->iocb.ulpCommand == CMD_CLOSE_XRI_CN)
+		abrt_iotag = iocbq->iocb.un.acxri.abortContextTag;
+		if (abrt_iotag != 0 && abrt_iotag <= phba->sli.last_iotag) {
+			abrtiocbq = phba->sli.iocbq_lookup[abrt_iotag];
+			fip = abrtiocbq->iocb_flag & LPFC_FIP_ELS_ID_MASK;
+		} else
+			fip = 0;
+
+		if ((iocbq->iocb.ulpCommand == CMD_CLOSE_XRI_CN) || fip)
 			/*
-			 * The link is down so the fw does not need to send abts
+			 * The link is down, or the command was ELS_FIP
+			 * so the fw does not need to send abts
 			 * on the wire.
 			 */
 			bf_set(abort_cmd_ia, &wqe->abort_cmd, 1);
@@ -7895,7 +7917,7 @@ lpfc_sli_eratt_read(struct lpfc_hba *phba)
 		/* Check if there is a deferred error condition is active */
 		if ((HS_FFER1 & phba->work_hs) &&
 		    ((HS_FFER2 | HS_FFER3 | HS_FFER4 | HS_FFER5 |
-		     HS_FFER6 | HS_FFER7) & phba->work_hs)) {
+		      HS_FFER6 | HS_FFER7 | HS_FFER8) & phba->work_hs)) {
 			phba->hba_flag |= DEFER_ERATT;
 			/* Clear all interrupt enable conditions */
 			writel(0, phba->HCregaddr);
@@ -8211,7 +8233,8 @@ lpfc_sli_sp_intr_handler(int irq, void *dev_id)
 			 */
 			if ((HS_FFER1 & phba->work_hs) &&
 				((HS_FFER2 | HS_FFER3 | HS_FFER4 | HS_FFER5 |
-				HS_FFER6 | HS_FFER7) & phba->work_hs)) {
+				  HS_FFER6 | HS_FFER7 | HS_FFER8) &
+				  phba->work_hs)) {
 				phba->hba_flag |= DEFER_ERATT;
 				/* Clear all interrupt enable conditions */
 				writel(0, phba->HCregaddr);