wl1251: make wl1251_set_partition bus agnostic

The same partition setting code can be used for both SPI and SDIO
modes, if we remove the spi-specific commands and use the more
generic buffer write routines.  Do that and move it to io.c
since it deals with register/memory address offsets.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1 files changed, 0 insertions, 124 deletions

diff --git a/drivers/net/wireless/wl12xx/wl1251_spi.c b/drivers/net/wireless/wl12xx/wl1251_spi.c
index 61a0852b4ee7..ceb237b4e579 100644
--- a/drivers/net/wireless/wl12xx/wl1251_spi.c
+++ b/drivers/net/wireless/wl12xx/wl1251_spi.c
@@ -115,130 +115,6 @@ static void wl1251_spi_reset_wake(struct wl1251 *wl)
 	wl1251_spi_init(wl);
 }
 
-
-/* Set the SPI partitions to access the chip addresses
- *
- * There are two VIRTUAL (SPI) partitions (the memory partition and the
- * registers partition), which are mapped to two different areas of the
- * PHYSICAL (hardware) memory.  This function also makes other checks to
- * ensure that the partitions are not overlapping.  In the diagram below, the
- * memory partition comes before the register partition, but the opposite is
- * also supported.
- *
- *                               PHYSICAL address
- *                                     space
- *
- *                                    |    |
- *                                 ...+----+--> mem_start
- *          VIRTUAL address     ...   |    |
- *               space       ...      |    | [PART_0]
- *                        ...         |    |
- * 0x00000000 <--+----+...         ...+----+--> mem_start + mem_size
- *               |    |         ...   |    |
- *               |MEM |      ...      |    |
- *               |    |   ...         |    |
- *  part_size <--+----+...            |    | {unused area)
- *               |    |   ...         |    |
- *               |REG |      ...      |    |
- *  part_size    |    |         ...   |    |
- *      +     <--+----+...         ...+----+--> reg_start
- *  reg_size              ...         |    |
- *                           ...      |    | [PART_1]
- *                              ...   |    |
- *                                 ...+----+--> reg_start + reg_size
- *                                    |    |
- *
- */
-int wl1251_set_partition(struct wl1251 *wl,
-			  u32 mem_start, u32 mem_size,
-			  u32 reg_start, u32 reg_size)
-{
-	struct wl1251_partition *partition;
-	struct spi_transfer t;
-	struct spi_message m;
-	size_t len, cmd_len;
-	u32 *cmd;
-	int addr;
-
-	cmd_len = sizeof(u32) + 2 * sizeof(struct wl1251_partition);
-	cmd = kzalloc(cmd_len, GFP_KERNEL);
-	if (!cmd)
-		return -ENOMEM;
-
-	spi_message_init(&m);
-	memset(&t, 0, sizeof(t));
-
-	partition = (struct wl1251_partition *) (cmd + 1);
-	addr = HW_ACCESS_PART0_SIZE_ADDR;
-	len = 2 * sizeof(struct wl1251_partition);
-
-	*cmd |= WSPI_CMD_WRITE;
-	*cmd |= (len << WSPI_CMD_BYTE_LENGTH_OFFSET) & WSPI_CMD_BYTE_LENGTH;
-	*cmd |= addr & WSPI_CMD_BYTE_ADDR;
-
-	wl1251_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
-		     mem_start, mem_size);
-	wl1251_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
-		     reg_start, reg_size);
-
-	/* Make sure that the two partitions together don't exceed the
-	 * address range */
-	if ((mem_size + reg_size) > HW_ACCESS_MEMORY_MAX_RANGE) {
-		wl1251_debug(DEBUG_SPI, "Total size exceeds maximum virtual"
-			     " address range.  Truncating partition[0].");
-		mem_size = HW_ACCESS_MEMORY_MAX_RANGE - reg_size;
-		wl1251_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
-			     mem_start, mem_size);
-		wl1251_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
-			     reg_start, reg_size);
-	}
-
-	if ((mem_start < reg_start) &&
-	    ((mem_start + mem_size) > reg_start)) {
-		/* Guarantee that the memory partition doesn't overlap the
-		 * registers partition */
-		wl1251_debug(DEBUG_SPI, "End of partition[0] is "
-			     "overlapping partition[1].  Adjusted.");
-		mem_size = reg_start - mem_start;
-		wl1251_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
-			     mem_start, mem_size);
-		wl1251_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
-			     reg_start, reg_size);
-	} else if ((reg_start < mem_start) &&
-		   ((reg_start + reg_size) > mem_start)) {
-		/* Guarantee that the register partition doesn't overlap the
-		 * memory partition */
-		wl1251_debug(DEBUG_SPI, "End of partition[1] is"
-			     " overlapping partition[0].  Adjusted.");
-		reg_size = mem_start - reg_start;
-		wl1251_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
-			     mem_start, mem_size);
-		wl1251_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
-			     reg_start, reg_size);
-	}
-
-	partition[0].start = mem_start;
-	partition[0].size  = mem_size;
-	partition[1].start = reg_start;
-	partition[1].size  = reg_size;
-
-	wl->physical_mem_addr = mem_start;
-	wl->physical_reg_addr = reg_start;
-
-	wl->virtual_mem_addr = 0;
-	wl->virtual_reg_addr = mem_size;
-
-	t.tx_buf = cmd;
-	t.len = cmd_len;
-	spi_message_add_tail(&t, &m);
-
-	spi_sync(wl->spi, &m);
-
-	kfree(cmd);
-
-	return 0;
-}
-
 static void wl1251_spi_read(struct wl1251 *wl, int addr, void *buf,
 			    size_t len)
 {